Casio 2760 Watch User Manual

MO0406-EA
Operation Guide 2760 2761
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully and keep it on hand for later reference
when necessary.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright
light.
• Be sure to read “Power Supply” of this manual for important information you
need to know when exposing the watch to bright light.
About This Manual
• Button operations are indicated using the letters shown
Stopwatch 1/20
in the illustration.
second dial
• Most of the display examples in this manual show only
Hour hand
Minute hand the digital display, without the analog hands.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
If the digital display of the watch is blank...
Digital display
If the digital display of the watch is blank, it means that the
watch’s Power Saving function has turned it off to
conserve power.
Power Saving automatically turns off the display and
enters a sleep state whenever the watch is left for a
certain period where it is dark.
• The initial factory default setting is Power Saving on.
• The watch will recover from the sleep state if you move it
to a well-lit area,* if you press any button, or if you angle
the watch towards your face for reading.
* It can take up to two seconds for the display to turn on.
• See “Power Saving” for more information.
General Guide
• Press C to change from mode to mode.
• In any mode, press D to illuminate the face of the watch.
Timekeeping Mode
Second
Digital display
hand 24-hour dial
Battery level dial
• Entering the Stopwatch Mode causes the second hand and battery level dial hand to
move to the 12 o’clock position.
Recall Mode
Dual Time Mode
Stopwatch Mode
▲
▲
▲
Press C.
▲
Alarm Mode
Hand Setting Mode
▲
▲
Radio-controlled Timekeeping
Current Time Setting
lll
lll
Year Month – Day
Press A.
Hour : Minutes
▲
lllllll
2. Use D (+) and B (–) to select the time zone you want to use as your Home Time
Zone.
• The GMT differential values for major cities in the Western Europe time zones are
shown below. Note that if the time zone you selected is in Daylight Saving Time
and the signal receiving indicator ( ) is on the display (indicating that the watch
has received a signal and has adjusted its GMT differentials for Daylight Saving
Time), you must select the GMT differential values shown in the parentheses.
+ 1.0 (DST + 2.0): Paris, Berlin, Milan, Rome, Amsterdam, Hamburg, Frankfurt,
Vienna, Barcelona, Madrid
+ 0.0 (DST + 1.0): London
3. Press A to exit the setting screen.
• The second hand will advance at high speed to the correct position in accordance
with the seconds count of the digital time, and resume normal movement from there.
• Normally, your watch should show the correct time as soon as you specify your
Home Time Zone. If it does not, it should adjust automatically after the next auto
receive operation (in the middle of the night). You can also perform manual receive
or you can set the time manually.
• Selecting +1.0 or +0.0 as your Home Time Zone automatically turns on auto receive.
When auto receive is turned on and you are within the reception range, the watch
will automatically receive the time calibration signal from the applicable transmitter
(in the middle of the night) and update its settings accordingly. For information about
the relationship between time zones (GMT differential values) and transmitters, see
“Transmitters”.
• See the maps under “Reception Ranges” for information about the reception ranges
of the watch.
• If you are in an area that does not use Daylight Saving Time (summer time), turn off
the DST setting.
• If A, D77.5, M60, or OFF starts to flash in place of the GMT differential value when
you hold down A in step 1 of the above procedure, press A again to exit the
setting screen. After that, press B and then perform step 1 again.
Month – Day
▲
ll
To specify your Home Time Zone
1. In the Timekeeping Mode, hold down A until the GMT
DST indicator
differential value starts to flash, which indicates the
setting screen.
• The second hand will move at high speed to the 12
o’clock position, where it will stop.
l l l l llll
• The GMT differential value indicates the time
difference in hours between Greenwich Mean Time
and the currently selected time zone.
• The DST indicator indicates that Daylight Saving Time
(summer time) is turned on for the currently selected
GMT differential value
time zone.
Day of week
PM indicator
Seconds
▲
Receive time
▲
This watch automatically adjusts its digital time setting in accordance with a time
calibration signal. You can also perform a manual procedure to set the time and date,
when necessary.
• The first thing you should do after purchasing this watch is to specify your Home
Time Zone, which is the time zone where you will normally use the watch. For more
information, see “To specify your Home Time Zone” below.
• When using the watch outside the range of the Germany and England time signal
transmitters, you have to adjust the current time setting manually as required. See
“Timekeeping” for more information about manual time settings.
• The analog time of this watch is synchronized with the digital time. Because of this,
the analog time setting is adjusted automatically whenever you change the digital
setting. See “Analog Timekeeping” for more information.
To display the digital time and last signal screen
• In the Timekeeping Mode, press A to cycle through the digital time screens as
shown below.
• In the Timekeeping Mode, press B to display the last signal screen. The last signal
screen shows the date and time of the last successful time calibration signal
reception.
▲
This watch receives a time calibration signal and updates its time setting accordingly.
The time calibration signal includes both Standard Time and Daylight Saving Time
(summer time) data.
• This watch is designed to pick up the time calibration signal transmitted in Germany
(Mainflingen) and England (Rugby).
Receive date
Press B.
Last Signal Screen
• The last signal screen remains on the display for about one or two minutes. After
that, the Timekeeping Mode screen reappears.
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive. The second hand stops at the 12 o’clock position
while time calibration signal reception is in progress. After reception is complete, the
second hand moves automatically until it matches the digital time.
• Auto Receive
With auto receive, the watch automatically picks up the time calibration signal five
times a day at 0:00 a.m., 1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. For more
information, see “About Auto Receive”.
• Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive”.
Important!
• When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o’clock side facing towards a window.
Make sure there are no metal objects nearby.
Resin Band
Metal Band
• The watch should not be on its side or facing the wrong way.
1
Operation Guide 2760 2761
lll
l l l l lll
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances,
office
equipment,
or a mobile
phone
Near a
construction
site, airport, or
other sources
of electrical
noise
Near hightension
power lines
Among or
behind
mountains
• Signal reception is normally better at night than during the day.
• Time calibration signal reception takes from two to seven minutes, but in some
cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
• When within range of the applicable transmitter, this watch can receive either the
Germany (Mainflingen) or England (Rugby) time calibration signals. See
“Transmitters” for more information.
lll
To perform manual receive
1. Place the watch on a stable surface so its top (12
o’clock side) is facing towards a window.
2. While any screen other than the last signal screen is on
ll llllll
the display in the Timekeeping Mode, hold down B for
about two seconds until the watch beeps.
3. Release B and the current date or time will flash to
indicate that signal reception has started.
• When a receive operation starts, the second hand will
Receiving indicator
move at high speed to the 12 o’clock position where it
will stop until the receive operation is complete.
lll
• Proper signal reception can be difficult or even impossible under the conditions listed
below.
• Time calibration signal reception takes from two to seven minutes, but in some
cases it can take up to 14 minutes. Take care that you do not perform any button
operations or move the watch during this time.
• After signal reception is complete, the watch beeps and the display of the watch
changes to the last signal screen.
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press B.
• If the receive operation is unsuccessful, – – – – – – appears on the display for about
one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the last signal or – – – – – – screen to the normal
timekeeping screen by pressing B.
Reception Ranges
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
1,500 kilometers
Problem
Cannot
perform
manual
receive.
Rugby
500 kilometers
Mainflingen
• Under good reception conditions, signal reception is possible within a radius of
about 1,500 kilometers from a transmitter.
• At distances further than about 500 kilometers from a transmitter, signal reception
may not be possible during certain times of year or times of day. Radio interferance
may also cause problems with reception.
• See the information under “Signal Reception Troubleshooting” if you experience
problems with time calibration signal reception.
About Auto Receive
When auto receive is turned on, the watch automatically starts to receive the time
calibration signal when the digital time in the Timekeeping Mode reaches 0:00 a.m.,
1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. each day (calibration times). The watch
will also perform an additional auto receive operation at 5:00 a.m. if none of the
regularly scheduled auto receive operations are successful.
Probable Cause
What you should do
• The watch is not in the Timekeeping • Enter the Timekeeping Mode
Mode.
and try again.
• Your current Home Time Zone
• Select +1.0 or +0.0 as your
setting is not one of the following:
Home Time Zone.
+1.0 or + 0.0.
• Select the transmitter setting
• The transmitter setting is incorrect.
appropriate for your current
location.
Auto receive • The transmitter setting is incorrect. • Select the transmitter setting
is turned on, • You changed the time setting
appropriate for your current
but the Level
manually.
location.
4 receiving
• Perform manual signal
• The watch was not in the
indicator
receive or wait until the next
Timekeeping or Dual Time Mode, or
does not
you performed some button operation auto signal receive operation
appear on
is performed.
during the auto receive operation.
the display.
• Check to make sure the
• Even if receive is successful, the
watch is in a location where it
Level 4 receiving indicator
disappears every day at 3 a.m.
can receive the signal.
Time setting • If the time is one hour off, the DST • Change the DST setting to
setting may be incorrect.
Auto DST.
is incorrect
• The Home Time Zone setting is not
• Select the correct Home
following
Time Zone.
signal
correct for the area where you are
reception.
using the watch.
Note
• Auto receive turns on automatically whenever you select +1.0 or +0.0 as your Home
Time Zone. For information about turning off auto receive, see “To select the
transmitter mode”.
• The auto receive operation is performed only if the watch is in the Timekeeping
Mode or Dual Time Mode when one of the calibration times is reached. It is not
performed if a calibration time is reached while an alarm is sounding, or while you
are configuring settings (while settings are flashing on the display).
• Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can easily receive the signal.
• When auto receive is turned on, the watch receives the calibration signal for two to
seven minutes everyday when the time in the Timekeeping Mode reaches each of
the calibration times. Do not perform any button operation within seven minutes
before or after any one of the calibration times. Doing so can interfere with correct
calibration.
• Remember that reception of the calibration signal depends on the current time on
the digital display. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the displayed
time is actually the correct time.
• When two, three, four, or five receptions are successful, the watch uses the data of
the last reception for calibration. When only one reception is successful, the watch
uses the data of the successful reception.
• For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Timekeeping Precautions”.
About the Receiving Indicator
Note
• “Lap time” is the time spent to cover a specific segment of a race, such as one lap
around a track. “Split time” is the time spent from the beginning of a race up to a
certain point.
• The stopwatch continues to run, restarting from zero after it reaches its limit, until
you stop it.
• The stopwatch measurement operation continues even if you exit the Stopwatch
Mode.
• The hand of the stopwatch 1/20 second dial revolves for the first minute of each
elapsed time operation. After that, it stops automatically at the 12 o’clock position. If
you exit the Stopwatch Mode while an elapsed time operation is in progress, the
1/20 second hand will revolve for the first minute after you re-enter the Stopwatch
Mode. When you stop an elapsed time measurement, the 1/20 second hand will
move automatically from the 12 o’clock position to the current 1/20 second count.
• For information about how stopwatch times are stored in memory, see “Memory
Management”.
• You can adjust the positions of the stopwatch 1/20 second dial and battery level dial
hands if they do not align exactly with the 12 o’clock position. See “Adjusting Dial
Hand Positions” for more information.
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
Weak
(Level 1)
Strong
(Level 4)
Receiving indicator
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• The Level 4 receiving indicator remains on the display in all modes following
reception of the time calibration signal and calibration of the watch’s time setting.
The Level 4 receiving indicator is not displayed if signal reception was unsuccessful
or after manual adjustment of the current time setting.
• The Level 4 receiving indicator indicates that at least one of the calibration signal
receive operations was successful. Note, however, that the Level 4 receiving
indicator is cleared from the display at 3:00 a.m. each day.
Stopwatch
The stopwatch lets you measure elapsed time, lap times,
Second hand
Battery
Stopwatch 1/20 split times, and two finishes. Stopwatch times are also
stored in memory.
level dial
second dial
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
• Entering the Stopwatch Mode causes the second hand
and battery level dial hand to move to the 12 o’clock
position.
• In the Stopwatch Mode, the second hand shows the
seconds of the elapsed time measurement, the battery
level dial shows elapsed minutes, and the stopwatch
1/20 second dial shows elapsed 1/20 second.
Minutes 1/100 second
Seconds
To measure elapsed time
1. Press B to start the stopwatch.
2. Press B again to stop the stopwatch.
• You can resume the measurement operation by pressing B.
3. Press A to clear the stopwatch to all zeros.
2
Operation Guide 2760 2761
To measure lap times
1. When the stopwatch display shows all zeros, press A
to display the lap time screen (indicated by LAP).
2. Press B to start a time measurement.
3. Press A to record the time of the first lap.
• This freezes the current lap time on the digital display
for about five seconds, while measurement of the next
lap time continues internally and elapsed time
continues to be indicated by the analog hands.
• After five seconds, the lap number of the displayed
time appears for one second, and then the elapsed
time display for the next lap appears.
4. Repeat step 3 to record more lap times.
5. Press B to stop the stopwatch.
6. Press A to clear the stopwatch to all zeros.
• Lap numbers are automatically incremented starting from 1 whenever you press A
in step 3 of the above procedure. The maximum lap number is 99. Recording a lap
after that causes the lap number count to restart from 00.
To delete all stopwatch time records
In the Recall Mode, hold down A and B for about two seconds. During that time
– –:– –. – – will flash on the digital display. Keep A and B depressed until
– –:– –. – – stops flashing.
• If you release A and B before – –:– –. – – stops flashing, the watch will return to
the stopwatch time record screen without deleting time records.
• The lap number will show LAP – – after all of the stopwatch time records are
deleted.
• Note that lap and split times cannot be deleted individually.
• Stopwatch time records can be deleted only when the Stopwatch Mode elapsed time
display is cleared to all zeros.
Dual Time
GMT differential value
To measure split times
1. When the stopwatch display shows all zeros, press A
to display the split time screen (indicated by SPL).
2. Press B to start a time measurement.
3. Press A to record the time of the first split.
• This freezes the current split time on the digital
display for about five seconds, while measurement of
the next split time continues internally and elapsed
time continues to be indicated by the analog hands.
• After five seconds, the elapsed time display for the
next split appears.
4. Repeat step 3 to record more split times.
5. Press B to stop the stopwatch.
6. Press A to clear the stopwatch to all zeros.
To time first and second place finishes
1. When the stopwatch display shows all zeros, press A to display the split time
screen (indicated by SPL).
2. Press B to start a time measurement.
3. Press A when the first finisher crosses the finish line.
• This freezes the time of the first finisher on the digital display for about five
seconds. After that, the display returns to elapsed time measurement.
4. Press B when the second finisher crosses the finish line, and display the time.
5. Press A to clear the stopwatch to all zeros.
Memory Management
Any time you start a new elapsed time measurement (from all zeros) in the Stopwatch
Mode, the watch automatically deletes all of the stopwatch time records currently in
memory.
• The following table shows Stopwatch Mode operations, and how they affect memory
storage.
To do this:
Clear all stopwatch times from memory and
start elapsed time measurement
Pause an elapsed time measurement without
storing data in memory
Restart a paused elapsed time measurement
without storing data in memory
Record a lap or split time in memory during
ongoing elapsed time measurement
Record the currently paused elapsed, lap, or
split time in memory
Press this button:
B (when all zeroes are displayed)
B
B
Current time in the
selected time zone
To view the time in another time zone
While in the Dual Time Mode, press B to scroll westward through time zones.
• When you release B, the displayed GMT differential value is replaced by the
current time in that time zone after about one second.
• Pressing A causes the applicable GMT differential value of the currently selected
time zone to appear on the digital display for about one second.
• If the current time shown for a time zone is wrong, check the Timekeeping Mode
time setting and your Home Time Zone setting, and make the necessary changes.
To toggle a time zone between Standard Time and Daylight Saving Time
1. In the Dual Time Mode, use B to display the time zone
DST indicator
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator appears on the display whenever you display a time zone for
which Daylight Saving Time is turned on.
• The DST/Standard Time setting you configure affects only the currently displayed
time zone. Other time zones are not affected.
• Note that you cannot use the Dual Time Mode to change the DST setting of the
Home Time Zone you currently have selected in the Timekeeping Mode. See “To
change the Daylight Saving Time (summer time) setting” for information about
turning the Home Time Zone DST setting on and off.
• The G0.0 time (Greenwich Mean Time) zone cannot be switched between Standard
Time and Daylight Saving Time.
A
A (clears display to all zeros)
Alarms
The Alarm Mode gives you a choice of four one-time
Alarm number alarms and one snooze alarm. One of the one-time
• The watch has enough memory to hold up to 50 lap/split time records. Recording a
lap or split time while there are already 50 records in memory deletes the oldest
record to make room for the new one.
• See “Recall Mode” for details on how to recall time records from memory.
Recall Mode
Lap number
The Dual Time Mode lets you view the current time in 29
time zones around the world.
• Time zones are indicated on the digital display by their
GMT differential values.
• For full information on time zones, see the “Time Zone
Table”.
• The watch will perform a signal receive operation even if
it is in the Dual Time Mode when a calibration time is
reached. If this happens, the Dual Time Mode time
settings will be adjusted in accordance with the current
time in the Timekeeping Mode’s Home Time Zone.
• All of the operations in this section are performed in the
Dual Time Mode, which you enter by pressing C.
Use the Recall Mode to recall and delete time records
stored in the Stopwatch Mode. You can use the Recall
Mode to view both lap and split time records.
• All of the operations in this section are performed in the
Recall Mode, which you enter by pressing C.
• Entering the Recall Mode displays the number of the
last lap recorded in the Stopwatch Mode. After that, the
applicable lap time appears. If there are no stopwatch
time records in memory, LAP – – appears on the
display.
Alarm time On/Off status
(Hour : Minutes)
alarms functions as a “target alarm”, which counts the
time remaining from the current time in your Home Time
Zone until the target alarm time.
Also use the Alarm Mode to turn the Hourly Time Signal
on and off.
• There are five alarms numbered AL1, AL2, AL3, AL4
(target alarm), and AL5 (snooze alarm). You can
configure AL5 as a snooze alarm only. Alarms AL1,
AL2, AL3, and AL4 can be used as one-time alarms
only.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Hourly Time
Signal Screen
To set an alarm time
1. In the Alarm Mode, use B to scroll through the alarm
screens until the one whose time you want to set is
displayed.
Minutes 1/100 second
Seconds
To recall stopwatch time records
1. In the Recall Mode, press A to select the either lap time or split time format.
▲
llll
lll
▲
Lap Time Format
llll
lll
Press A.
Split Time Format
2. Press B to scroll through the stopwatch time records from the newest to the
oldest.
• Each press of B displays the next lap or split number for about one second, and
then displays the applicable lap or split time.
• Regardless of whether you are viewing time records using lap time format or split
time format, the lap/split number is indicated on the display as LAP 1, LAP 2, etc.
AL 1
AL 2
AL 3
:00
AL 5
AL 4
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
• With the target alarm (AL4), the time starts to countdown as soon as you set the
alarm time.
Target Alarm Time
Countdown (Hours, Minutes, Seconds)
3
Operation Guide 2760 2761
Alarm Operation
Daylight Saving Time (DST)
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
The target alarm counts the time remaining from the current time in your Home Time
Zone until the target alarm time. Note that the target alarm repeats automatically each
day, as long as it is turned on. You need to turn off the target alarm to disable it.
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the snooze alarm (AL5) setting screen
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
The time calibration signals include both Standard Time and DST data. When the auto
DST setting is turned on, the watch switches between Standard Time and DST
(summer time) automatically in accordance with the signal it receives.
• The auto DST setting can be turned on only while +0.0, +1.0 or +2.0 is selected as
the Home Time Zone.
• If you experience problems receiving the time calibration signal in your area, it is
probably best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
To test the alarm
In the Alarm Mode, hold down B to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use B to select an alarm or the
Snooze alarm indicator
Hourly Time Signal.
2. Press A to toggle it on (on displayed) and off (oF
displayed).
• You need to display the screen of a daily alarm (AL1 to
AL5) or the Hourly Time Signal in order to check its
current on/off status.
• Turning on the snooze alarm displays the snooze alarm
On/Off status
indicator on its Alarm Mode screen and in all modes.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Hourly Time Signal Screen
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
• All of the operations in this section are performed in the Timekeeping Mode, which
you enter by pressing C.
Day of week
Month – Day
Year Month – Day
Hour : Minutes
▲
▲
Press A.
▲
PM indicator
To change the Daylight Saving Time (summer time) setting
1. While any screen other than the last signal screen is on the display in the
Timekeeping Mode, hold down A until the GMT differential value starts to flash,
which indicates the setting screen.
2. Press C to display the DST setting screen.
3. Press D to cycle through the DST settings in the sequence shown below.
Auto DST (A)
4. Press A to exit the setting screen.
• The DST indicator appears on the display to indicate that Daylight Saving Time is
turned on.
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
• The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting manually
When the digital time setting is changed by time calibration signal reception
When you change the Home Time Zone and/or DST setting
• Whenever you need to adjust both the digital and the analog time settings manually,
make sure you adjust the digital setting first.
• Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
1. In the Timekeeping Mode, press C five times to enter
Second hand
the Hand Setting Mode.
Hour hand
Minute hand 2. Hold down A until – 0 0 – starts to flash, which
▲
Press B.
Last Signal Screen
lll
lllllll
DST
12/24-Hour
Format
Seconds
Hour
Power
Saving
Day
Month
Year
Minutes
|||
||
|| |||
|||||
GMT differential
value
||||||
ll
GMT differential value
• The GMT differential value indicates the time difference in hours between
Greenwich Mean Time and the currently selected time zone.
• The DST indicator indicates that Daylight Saving Time (summer time) is turned on
for the currently selected time zone.
2. Use D (+) and B (–) to select the time zone you want to use as your Home Time
Zone.
• For full details about GMT differential values, see the “Time Zone Table”.
3. Press C to move the flashing in the sequence shown below to select other
settings.
||||||
|||
To set the digital time and date manually
1. While any screen other than the last signal screen is on
DST indicator
the display in the Timekeeping Mode, hold down A
until the GMT differential value starts to flash, which
indicates the setting screen.
l
l
l
l
l
ll
l
• The second hand will move at high speed to the 12
o’clock position, where it will stop.
24-hour dial
|||
Make sure you select your Home Time Zone before you change the current time and
date settings. Dual Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, Dual Time Mode times will not be correct
if you do not select the proper Home Time Zone before setting the time and date in the
Timekeeping Mode.
• When setting the time and date, you can also configure settings for your Home Time
Zone (the time zone where you normally use the watch), summer time (Daylight
Saving time or DST), 12/24-hour format, and power saving on/off.
|||
Setting the Digital Time and Date Manually
lll
DST on (on)
To adjust the analog time
Seconds
▲
Illumination
Auto light switch
on indicator
Toggle between Daylight Saving Time (on),
Standard Time (OFF), or Auto DST (A)
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Reset the seconds to 00
Change the hour or minutes
Change the year, month, or day
Press D.
Press D.
Use D (+) and B (–).
Use D (+) and B (–).
Toggle power saving on (on) and off (OFF)
Press D.
Press D.
To illuminate the face of the watch
In any mode (except when a setting screen is on the display), press D to illuminate
the face of the watch.
• The above operation turns on illumination regardless of the current auto light switch
setting.
To specify the illumination duration
1. While any screen other than the last signal screen is on
the display in the Timekeeping Mode, hold down A
until the GMT differential value starts to flash, which
llll
indicates the setting screen.
2. Press C three times to move the flashing to the
second setting.
3. Press B to toggle the illumination duration setting
between 2 seconds (“.” displayed in front of seconds)
and 1.5 seconds (“.” not displayed).
4. Press A to exit the setting screen.
llll
Do this:
Use D (+) and B (–).
llll
5. Press A to exit the setting screen.
• When you exit the setting screen, the analog hands are adjusted automatically to
match the digital time. See “Analog Timekeeping” for more information.
• Auto DST (A) can be selected only while +0.0, +1.0 or +2.0 is selected as the Home
Time Zone. For more information, see “Daylight Saving Time (DST)” below.
Two LEDs (light-emitting diodes) illuminate the face of the
watch for easy reading in the dark.
The watch’s auto light switch automatically illuminates the
face when you angle the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• You can specify 1.5 seconds or 2 seconds as the
illumination duration.
• See “Illumination Precautions” for other important
information.
llll
To do this:
Change the time zone
indicates the analog setting screen.
• The second hand will move at high speed to the 12
o’clock position, where it will stop.
3. If the second hand is not pointing precisely at 12 o’clock
at this time, use D to adjust its position.
• Each press of D causes the second hand to advance
by one second.
4. Press C. This will cause the Timekeeping Mode time
on the digital display to flash, which indicates that
adjustment of hour and minute hands is selected.
5. Use D (+) and B (–) to move the hands in 20-second
units.
• Holding down either button moves the hands at high
speed.
• Adjust the analog time so it matches the digital time. Note that the 24-hour dial
hand moves in coordination with the hour and minute hands. When adjusting the
analog time, keep an eye on the 24-hour dial hand to make sure that it is in the
correct am/pm position.
• To move the hands forward a long way, hold down D, press B, and then release
both buttons.
• To move the hands back a long way, hold down B, press D, and then release
both buttons.
• The above operations cause the hands to move at high speed until you press any
button or until the hands complete one 24-hour cycle (two revolutions). Hand
movement also stops if an alarm starts to sound.
6. Press A twice to exit the setting screen.
• The first press of A causes 00:00.00 to appear on the display (indicating the
stopwatch 1/20 second dial hand adjustment screen). Pressing A the second time
exits the setting screen.
• To return to the Timekeeping Mode, press C.
4. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen
DST off (OFF)
4
Operation Guide 2760 2761
About the Auto Light Switch
Turning on the auto light switch causes the face to illuminate, whenever you position
your wrist as described below in any mode. Note that this watch features a “Full Auto
LED Light”, so the auto light switch operates only when available light is below a
certain level. It does not illuminate the face under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
More than
40°
Warning!
• Always make sure you are in a safe place whenever you are reading the face
of the watch using the auto light switch. Be especially careful when running or
engaged in any other activity that can result in accident or injury. Also take
care that sudden illumination by the auto light switch does not surprise or
distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode (except when a setting screen is on the display), hold down D for about
two seconds to toggle the auto light switch on (
displayed) and off (
not
displayed).
• The auto light switch on indicator (
) is on the display in all modes while the auto
light switch is turned on.
• Leaving the watch exposed to direct sunlight or some other very strong light source
can cause the battery level dial to temporarily show a reading that is higher than the
actual battery level. The correct battery level should be indicated after a few minutes.
• If you use the illumination or alarms a number of times during a short period, the
recover indicator (R) appears on the display and the following operations become
disabled until battery power recovers.
Illumination; Beeper tone; Coordination between digital and analog timekeeping;
Time calibration signal reception
After some time, battery power will recover and the recover indicator will disappear,
indicating that the above functions are enabled again.
• If the recover indicator appears frequently, it probably means that remaining battery
power is low. Leave the watch in bright light to allow it to charge.
Charging Precautions
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to a lower temperature.
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it
to become quite hot. Take care when handling the watch to avoid burn injury.
The watch can become particularly hot when exposed to the following
conditions for long periods.
• On the dashboard of a car parked in direct sunlight
• Too close to an incandescent lamp
• Under direct sunlight
Charging Guide
After a full charge, timekeeping remains enabled for up to about five months.
• The following table shows the amount of time the watch needs to be exposed to light
each day in order to generate enough power for normal daily operations.
Exposure Level (Brightness)
Approximate Exposure Time
Outdoor Sunlight (50,000 lux)
5 minutes
Power Supply
Sunlight Through a Window (10,000 lux)
24 minutes
This watch is equipped with a solar cell and a special rechargeable battery (secondary
battery) that is charged by the electrical power produced by the solar cell. The
illustration shown below shows how you should position the watch for charging.
Daylight Through a Window on a Cloudy Day
(5,000 lux)
48 minutes
Indoor Fluorescent Lighting (500 lux)
8 hours
Example: Orient the watch so its face is
pointing at a light source.
• The illustration shows how to position
a watch with a resin band.
• Note that charging efficiency drops
when any part of the solar cell is
blocked by clothing, etc.
• Normally, you should try to keep the
watch outside of your sleeve as much
as possible. Charging is significantly
reduced if the face is only partially
covered.
Solar cell
Recovery Times
The table below shows the amount exposure that is required to take the battery from
one level to the next.
Dial and
Digital Display
1
All functions enabled.
2
All functions enabled.
Except for internal timekeeping
and the C indicator, all functions
and display indicators are
A
(Charge soon alert) disabled.
All functions disabled.
lllll
lll
lll
3
lll
ll
ll
llll
Function Status
llllll
Recover indicator
4
• The battery level dial shows the battery power level in all modes except for the
Stopwatch Mode. In the Stopwatch Mode, the battery level dial indicates elapsed
minutes.
• The flashing C indicator at Level 3 tells you that battery power is very low, and that
exposure to bright light for charging is required as soon as possible.
• When battery power is at Level 3, analog hand movement and time calibration signal
reception are disabled.
• At Level 4, all functions are disabled and settings return to their initial factory
defaults. Functions are enabled once again after the rechargeable battery is
charged, but you need to set the digital time and date, after the battery reaches
Level 3 from Level 4. You will not be able to set any of the other settings until the
battery reaches Level 2 after dropping to Level 4.
• Display indicators reappear as soon as the battery is charged from Level 4 to Level
3.
Level 3
Outdoor Sunlight (50,000 lux)
Sunlight Through a Window
(10,000 lux)
Daylight Through a Window
on a Cloudy Day (5,000 lux)
Indoor Fluorescent Lighting
(500 lux)
Level 2
Level 1
▲
Level
Level 4
▲
The battery level dial and digital display show you the current level of the rechargeable
battery’s power. The digital display also shows a recover indicator, which lets you know
when there is a large load being placed on the battery.
Approximate Exposure Time
▲
Battery Power Levels
Exposure Level
(Brightness)
▲
Important!
• Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Make sure that the watch is normally exposed to bright light
whenever possible.
• This watch uses a special rechargeable battery to store power produced by the solar
cell, so regular battery replacement is not required. However, after very long use, the
rechargeable battery may lose its ability to achieve a full charge. If you experience
problems getting the special rechargeable battery to fully charge, contact your
dealer or CASIO distributor about having it replaced.
• Never try to remove or replace the watch’s special battery yourself. Use of the wrong
type of battery can damage the watch.
• All data stored in memory is deleted, and the current time and all other settings
return to their initial factory defaults whenever battery power drops to Level 4 and
when you have the battery replaced.
• Turn on the watch’s Power Saving function and keep it in an area normally exposed
to bright light when storing it for long periods. This helps to keep the rechargeable
battery from going dead.
Battery level dial
• Since these are the specs, we can include all the technical details.
• Watch is not exposed to light
• Internal timekeeping
• Display on 18 hours per day, sleep state 6 hours per day
• 1 light operation (1.5 seconds) per day
• 10 seconds of alarm operation per day
• 5 times calibration reception per day
• Stable operation is promoted by frequent charging.
1 hour
14 hours
4 hours
3 hours
71 hours
20 hours
5 hours
–––
49 hours
–––
• The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Return Features
• If you leave the watch in the Recall, Alarm (except for the target alarm countdown
screen), or Hand Setting Mode for two or three minutes without performing any
operation, it automatically returns to the Timekeeping Mode.
• If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Initial Screens
When you enter the Dual Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Radio-controlled Timekeeping Precautions
• Strong electrostatic charge can result in the wrong time being set.
• Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• The time calibration signal bounces off the ionosphere. Because of this, such factors
as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
5
Operation Guide 2760 2761
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make manually.
• The watch is designed to automatically update the date and day of the week for the
period January 1, 2000 to December 31, 2099. Setting of the date by the time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
• Though this watch is designed to receive both time data (hour, minutes, seconds)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
• Normally, the signal reception date shown by the last signal screen is the date data
included in the received time calibration signal. When only time data is received,
however, the last signal screen shows the date as kept in the Timekeeping Mode at
the time of signal reception.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps time within ±15 seconds a month at normal temperature.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your Home Time Zone value and DST
(summer time) settings, and transmitter mode setting. The following are the initial
factory defaults for these settings.
Setting
Initial Factory Default
GMT Differential Value
+1.0 (or DST +2.0): Module 2760
+0.0 (or DST +1.0): Module 2761
DST (summer time)
DS A (Auto switching)
Transmitter mode
A (Automatic selection)
2760
• To find out the module number of your watch, look at its
back cover. The Module number (2760 or 2761) will be
engraved inside the box on the back cover.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC*) data.
is the world-wide scientific standard of timekeeping. It is based upon carefully
* UTC
maintained atomic (cesium) clocks that keep time accurately to within
microseconds. Leap seconds are added or subtracted as necessary to keep UTC
in sync with the Earth’s rotation. The reference point for UTC is Greenwich,
England.
12-hour/24-hour Timekeeping Formats
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
Power Saving
When turned on, Power Saving automatically enters a sleep state whenever the watch
is left for a certain period in an area where it is dark. The table below shows how
watch functions are affected by Power Saving.
• There are actually two sleep state levels: “display sleep” and “function sleep”.
Elapsed Time in Dark
Operation
3 to 4 days
(Display Sleep)
Digital display off, but all functions enabled
8 days or more
(Function Sleep)
• Digital display off
• All functions, including analog timekeeping, disabled
• Internal timekeeping maintained
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
The watch does this:
The first signal search operation after
1. Checks the Mainflingen signal first.
factory default settings are in effect, or after 2. If the Mainflingen signal cannot be
the Home Time Zone has been changed.
received, checks the Rugby signal.
1. Checks the last successfully received
Any case other than the above.
signal first.
2. If the last successfully received signal
cannot be received, checks the other
signal.
To turn Power Saving on and off
1. While any screen other than the last signal screen is on
the display in the Timekeeping Mode, hold down A
until the GMT differential value starts to flash, which
| || | |
indicates the setting screen.
2. Press C nine times until the Power Saving on/off
screen appears.
3. Press D to toggle Power Saving on (on) and off (OFF).
4. Press A to exit the setting screen.
|||||
In this case:
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area. It can take up to two seconds for the display to turn
on.
• Press any button.
• Angle the watch towards your face for reading.
|||||
This watch is able to receive time calibration signals transmitted in Germany
(Mainflingen) and England (Rugby). You can select either one of the transmitters, or
you can configure the watch to select the transmitter that has the strongest signal
automatically.
• The following explains how the watch determines which transmitter it should check
first while the watch is configured for automatic transmitter selection.
Module 2760
|||||
Transmitters
Adjusting Dial Hand Positions
You can use the procedure in this section to adjust the position of the stopwatch 1/20
second dial hand and the battery level dial hand whenever they do not align with the
12 o’clock position when you enter the Stopwatch Mode.
Module 2761
1. Checks the last successfully received
signal first.
2. If the last successfully received signal
cannot be received, checks the other
signal.
• Auto receive is turned on whenever the transmitter mode is A, D77.5, or M60. Auto
receive is turned off when the transmitter mode setting is OFF.
• Note that you can change the transmitter mode setting when +0.0 or +1.0 is
selected as the Home Time Zone.
• See “To select the transmitter mode” below.
|||||
|||||
To select the transmitter mode
1. In the Timekeeping Mode, press B to display the last
signal screen.
2. Hold down A until the transmitter mode setting starts
| || | |
to flash, which indicates the setting screen.
• If holding down A does not display the setting
screen, check the current Home Time Zone setting.
Press B to return to the Timekeeping Mode screen.
See “To specify your Home Time Zone” for more
information.
3. Use B or D to select the transmitter mode setting you
want to use.
|||||
• The following are the available transmitter mode settings.
A: Automatic selection of the Mainflingen or Rugby signal
D 77.5: Reception of the Mainflingen signal
M 60: Reception of the Rugby signal
OFF: Auto receive off
4. Press A to exit the setting screen and return to the last signal screen.
• If you want to the return to the Timekeeping Mode screen, press B.
• Signal reception can take up to 14 minutes when the A option is selected.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099. The day of the week is calculated
automatically in accordance with the date.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced or when battery power drops to
Level 4.
• The current time for all time zones in the Timekeeping Mode and Dual Time Mode is
calculated in accordance with the Greenwich Mean Time (GMT) differential of each
zone, based on your Home Time Zone time setting.
Stopwatch 1/20
second dial
lll llll
llll
1. Checks the Rugby signal first.
2. If the Rugby signal cannot be received,
checks the Mainflingen signal.
lllllll
The watch does this:
The first signal search operation after
factory default settings are in effect, or
after the Home Time Zone has been
changed.
Any case other than the above.
llll
In this case:
Battery level dial
Important!
Never move the battery level dial hand to any position
other than 12 o’clock. If you do, it will not correctly indicate
the battery power level.
To adjust dial hand positions
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until – 0 0 – starts to flash, which
indicates the analog setting screen.
3. Press A to display the dial hand setting screen.
• The dial hand setting screen shows 00:00.00, with the
two zeros on the far right flashing. This indicates that
the stopwatch 1/20 second dial is selected for
adjustment.
4. Press D to advance the hand of the stopwatch 1/20 second dial one step, until it is
aligned with the 12 o’clock position.
5. After the 1/20 second dial hand is aligned properly, press C.
• This causes the two far left zeros of the 00:00.00 figures to flash, which indicates
that the battery level dial is selected for adjustment.
6. Press D to advance the hand of the battery level dial one step, until it is aligned
with the 12 o’clock position.
7. Press A to exit the setting screen.
• To return to the Timekeeping Mode, press C.
Illumination Precautions
• The illumination provided by the light may be hard to see when viewed under direct
sunlight.
• Illumination automatically turns off whenever an alarm sounds.
• Frequent use of illumination shortens the battery operating time.
Auto light switch precautions
• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of
your arm can cause frequent activation of the auto light switch and illuminate the
face of the watch. To avoid running down the battery, turn off the auto light switch
whenever engaging in activities that might cause frequent illumination of the face.
• Note that wearing the watch under your sleeve while the auto light switch is turned
on can cause frequent illumination of the face and can run down the battery.
More than 15 degrees
too high
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off after about two seconds, even if
you keep the watch pointed towards your face.
6
Operation Guide 2760 2761
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back towards your face again. If this
does not work, drop your arm all the way down so it hangs at your side, and then
bring it back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Tachymeter
Tachymeter bezel
200
80
70
360
ER
70
60 TACH
YME
T
10
0
120
0
15
If your watch has a tachymeter bezel, you can perform the
steps below to calculate average speed after using the
Stopwatch Mode to measure the amount of time that it
takes to travel one kilometer (or one mile).
• Never try to perform stopwatch operations while you
are driving an automobile, riding a bicycle, or
operating any type of vehicle. Doing so is very
dangerous and can result in accident.
1 In the Stopwatch Mode, start an elapsed time
operation at any point you like.
2 Stop the elapsed time operation after you travel one
kilometer or one mile.
3 Your average speed will be the value that the second
hand is pointing to on the tachymeter bezel.
• The illustration shows an example where it took 50 seconds to travel one kilometer
by car. The second hand is pointing at 70, which indicates that the average speed is
70 kilometers per hour.
• See “Stopwatch” for details about using the stopwatch.
• The tachymeter can be used only when you are traveling by car or some other
means that can cover one kilometer or one mile within 60 seconds.
Time Zone Table
GMT Differential Value
Standard Time DST/Summer Time
–11.0
DST –10.0
–10.0
DST –9.0
–9.0
DST –8.0
–8.0
DST –7.0
–7.0
–6.0
DST
DST
–6.0
–5.0
–5.0
DST
–4.0
–4.0
–3.0
DST
DST
–3.0
–2.0
–2.0
–1.0
G 0.0
+0.0
+1.0
DST –1.0
DST +0.0
G 0.0
DST +1.0
DST +2.0
+2.0
DST
+3.0
+3.0
DST
+4.0
+3.5
+4.0
+4.5
+5.0
+5.5
+6.0
+6.5
+7.0
+8.0
DST
DST
DST
DST
DST
DST
DST
DST
DST
+4.5
+5.0
+5.5
+6.0
+6.5
+7.0
+7.5
+8.0
+9.0
+9.0
+9.5
+10.0
+11.0
+12.0
DST
DST
DST
DST
DST
+10.0
+10.5
+11.0
+12.0
+13.0
Major Cities in Time Zone
Pago Pago
Honolulu, Papeete
Anchorage, Nome
Los Angeles, San Francisco, Las Vegas, Vancouver,
Seattle/Tacoma, Dawson City, Tijuana
Denver, El Paso, Edmonton, Culiacan
Chicago, Houston, Dallas/Fort Worth, New Orleans,
Mexico City, Winnipeg
New York, Montreal, Detroit, Miami, Boston,
Panama City, Havana, Lima, Bogota
Caracas, La Paz, Santiago, Port of Spain
Rio De Janeiro, Sao Paulo, Buenos Aires, Brasilia,
Montevideo
Praia
(GMT)
London, Dublin, Lisbon, Casablanca, Dakar, Abidjan
Paris, Milan, Rome, Madrid, Amsterdam, Algiers,
Hamburg, Frankfurt, Vienna, Stockholm, Berlin
Cairo, Jerusalem, Athens, Helsinki, Istanbul, Beirut,
Damascus, Cape Town
Jeddah, Kuwait, Riyadh, Aden, Addis Ababa, Nairobi,
Moscow
Tehran, Shiraz
Dubai, Abu Dhabi, Muscat
Kabul
Karachi, Male
Delhi, Mumbai, Kolkata
Dhaka, Colombo
Yangon
Bangkok, Jakarta, Phnom Penh, Hanoi, Vientiane
Hong Kong, Singapore, Kuala Lumpur, Beijing, Taipei,
Manila, Perth, Ulaanbaatar
Tokyo, Seoul, Pyongyang
Adelaide, Darwin
Sydney, Melbourne, Guam, Rabaul
Noumea, Port Vila
Wellington, Christchurch, Nadi, Nauru Island
• Based on data as of December 2003.
7