Casio 2821 Watch User Manual

MA0309-EA
Operation Guide 2548/2821
About This Manual
• The operational procedures for Modules 2548 and 2821
are identical. All of the illustrations in this manual show
Module 2548.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
(Light)
Module 2548
Module 2821
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping Mode
e-DATA MEMORY Mode
Press
• Module 2821 does not display an AM indicator (A).
World Time Mode
Alarm Mode
Countdown Timer Mode
Stopwatch Mode
.
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
Hour : Minutes
Day of week
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.
Read This Before You Set the Time and Date !
The times displayed in the Timekeeping Mode and World
Time Mode are linked. Because of this, make sure you
select a city code for your Home City (the city where you
normally use the watch) before you set the time and date.
Month – Day
PM indicator
Daylight Saving Time (DST)
Seconds
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
City code
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time
(ON displayed) and Standard Time (OFF displayed).
• Note that you cannot switch between Standard Time
and Daylight Saving Time while GMT is selected as
the Home City code.
4. Press A to exit the setting screen.
• The DST indicator appears on the display to indicate
that Daylight Saving Time is turned on.
e-DATA MEMORY
You can use the watch’s e-DATA MEMORY to store e-mail
addresses, Web page URLs, and other text data.
You can also use a password to limit access to e-DATA
MEMORY contents.
• All of the operations in this section are performed in the
e-DATA MEMORY Mode, which you enter by pressing
C.
Text
Seconds
Day
DST
City Code
Hour
Year
12/24-Hour
Format
Month
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Screen
To do this:
Do this:
Reset the seconds to 00
Press D.
OFF
Toggle between Daylight Saving Time (0N)
and Standard Time (0FF)
Press D.
TYO
Change the city code
Use D (east) and B (west).
Change the hour or minutes
Use D (+) and B (–).
12H
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Press D.
2003
Change the year
Use D (+) and B (–).
6-30
Change the month or day
50
10:58
P
e-DATA MEMORY Management
Minutes
• For full information on city codes, see the “City Code Table”.
• See “Daylight Saving Time (DST)” for details about DST setting.
4. Press A to exit the setting screen.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m. Note that Module 2821 does not display an AM indicator
(A).
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Record number
(Page number)
e-DATA MEMORY can hold up to 315 characters total,
while each record can contain up to 63 characters. The
maximum number of records depends on the number of
characters per record, as shown below.
• 63 characters per record: 5 records
• 7 or fewer characters per record: 40 records
To create a new e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, press D and B at the
Remaining memory (%)
same time to display the remaining memory screen.
• If 0 % is shown for remaining memory, it means that
memory is full. To store another record, you will first
have to delete some of the records stored in memory.
2. Hold down A until the flashing cursor ( #) appears on
the display, which indicates the setting screen.
• The setting screen also shows the record number that
is automatically assigned to the new record.
3. Input the text you want.
• When inputting the text, use D (+) and B (–) to
cycle through characters at the current cursor
location, and C to move the cursor to the right. See
“Inputting Text”.
4. Press A to store your data and return to the e-DATA MEMORY record screen
(without the cursor).
• Pressing A causes the message SET to appear for about two seconds as the
data is stored. After that, the e-DATA MEMORY record screen appears.
• The text can show only three characters at a time, so longer text scrolls
continuously from right to left. The last character is indicated by the symbol s after
it. Press A to stop and restart scrolling.
• Records are stored in memory in the sequence they are created.
1
Operation Guide 2548/2821
To recall e-DATA MEMORY records
In the e-DATA MEMORY Mode, use D (+) and B (–) to cycle through e-DATA
MEMORY records as shown below.
Press
Record 1
(
)
World Time shows the current time in 27 cities (29 time
zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
City code
.
Remaining
memory
screen
Record 2
(
)
Press
World Time
Password
setting
screen
.
Timekeeping
Mode time
Current time in the zone
of the selected city code
Remaining Memory Screen
Password Setting Screen
• The value on the remaining memory screen is the percentage of memory that
is still available. It does not indicate the number of records that can be stored.
• The Password Setting screen shows xxxx when a password is already
registered.
• You can use the Password Setting screen to register, edit, or delete your
password. See “Using a Password to Protect e-DATA MEMORY Data” for
more information.
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record
you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D (+) and B (–) to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B (–) to display the record
you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The message CLR appears to indicate that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for
input.
4. Input data or press A to return to the remaining memory screen.
Using a Password to Protect e-DATA MEMORY Data
You can register a 4-digit password to keep e-DATA MEMORY data secure.
Important!
Use a 4-digit password that is easy for you to remember, but difficult for others
to decipher. If you forget the password, you will have to have your watch
initialized (which deletes all data in memory) in order to access the e-DATA
MEMORY again. To have the watch initialized, contact the store or dealer where
you purchased it, and ask to have the AC operation performed.
To register a new password
1. In the e-DATA MEMORY Mode, use D (+) and
B (–) to display the Password Setting screen.
• This displays a screen that shows SET PA55.
2. Hold down A for about one second until NEW
appears, with the first 0 flashing.
• This is the New Password Setting screen.
3. Use D (+) and B (–) to scroll through numbers at the first digit.
4. When the first digit is the number you want, press C to advance to the next digit.
5. Repeat steps 3 and 4 to input all four digits of the password you want.
• Pressing A while inputting a new password clears your input and returns to the
Password Setting screen.
6. After all four of the password digits are the way you want, press C to register
them.
• Pressing C causes the message SET to appear for about one second as the
password is stored. After that, the Password Setting screen appears.
• After registering a password, you can input, recall, edit and delete data, if you want.
After you exit the e-DATA MEMORY Mode, you will have to input the password
every time you want to enter it again.
To view the time in another city code
In the World Time Mode, press D to scroll through city
codes (time zones) to the east or B to scroll to the west.
• For full information about city codes, see the “City Code
Table”.
• If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make the necessary changes.
• When the currently selected time zone is one that includes
mostly ocean, a value indicating the zone’s Greenwich
Mean Time differential appears in place of a city code.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use B and D to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
• Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT is selected as the city code.
Alarms
Alarm number
Alarm time
(Hour : Minutes)
Timekeeping Mode time
You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms is a snooze alarm, while the
other four are one-time alarms. You can also input
reminder text that appears when the alarm time is
reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered AL1through
AL4 for the one-time alarm, a snooze alarm screen
indicated by SNZ. The Hourly Time Signal screen is
indicated by SIG.
• In the case of the snooze alarm screen, the snooze
alarm indicator (
) appears in the lower right corner
of the display.
• Alarm settings (and Hourly Time Signal settings) are available in the Alarm Mode,
which you enter by pressing C.
Alarm Types
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D and B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
Press
.
Press
.
To input the password
1. Enter the e-DATA MEMORY Mode.
2. On the Password Input screen (xxxx PA55), press D
or B. This causes the first digit of the password to
flash.
3. Input the password.
• Use D (+) and B (–) to scroll through numbers at
each digit.
• Press C to advance to the next digit.
• Pressing A while inputting the password clears your
input and returns to the Password Input screen.
4. After the password is the way you want, press C.
• If the input password matches the one registered, the message OK!appears,
followed by an e-DATA MEMORY screen.
• If the password does not match, the message ERR appears, followed by the
Password Input screen.
To change the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Perform the procedure starting from step 2 under “To register a new password” to
specify the new password.
• To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1through AL4. To set the snooze alarm, display the screen indicated
by SNZ.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour
Minutes
Month
Day
Text
• Selecting the text causes the text input cursor ( #) to appear. There are eight
spaces in the text, so you have to press C eight times to move to the Hour
setting.
To delete the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Hold down A for about one second until NEW appears, with the first 0 flashing.
4. Press B and D at the same time to delete the password.
• The message CLR appears to indicate that the password is being deleted. After the
password is deleted, the Password Setting screen appears.
2
Operation Guide 2548/2821
4. While a setting is flashing, use D, B, and C to change it as described below.
Screen
To do this:
Do this:
A
12:00
Change the hour
and minutes
x-xx
Change the
month and day
Use D (+) and B (–).
• With the 12-hour format, set the time correctly as a.m.
(A indicator) or p.m. (P indicator).
• To set an alarm that does not include a month and/or
day, set x for each setting.
#
Input reminder
text
Use D (+) and B (–) to cycle through characters at the
current cursor location, and C to move the cursor to the
right. See “Inputting Text”.
• Note that Module 2821 does not display an AM indicator (A).
• Pressing B and D at the same time while any setting is flashing automatically
sets the time to AM12:00 and the date to x-xx. It also clears any text that is input
for the alarm.
Alarm on indicator
5. Press A to exit the setting screen.
• If you input reminder text, the text appears in place of
the alarm number.
• If the reminder text is more than three characters, it will
scroll form right to left.
• If the alarm has a month and/or day setting, the month/
day appears at the bottom of the display, in place of the
Timekeeping Mode time.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• When the end of the countdown is reached and auto-repeat is turned on, the alarm
sounds, but the countdown starts again automatically whenever the countdown
reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press B. This returns the countdown time to its starting value.
To set up the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure “To use the countdown timer” to display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Hours
Snooze alarm indicator
3. While a setting is flashing, use D and B to change it as described below.
Alarm Operation
Graphic areas
All of the graphic area segments start to flash, starting
from the point the Timekeeping Mode time reaches one
hour before an alarm time. This pre-alarm feature lets you
know that an alarm time is about to be reached.
The alarm tone sounds at the preset time for 10 seconds,
regardless of the mode the watch is in. In the case of the
snooze alarm, the alarm operation is performed a total of
seven times, every five minutes, until you turn the alarm
off.
• To stop the alarm tone after it starts to sound, press any button.
• The pre-alarm feature works in the Timekeeping Mode only. To stop the pre-alarm
after it starts, press any button. Note, however, that pressing C also changes to the
e-DATA MEMORY Mode.
• If you input reminder text for an alarm, the text appears for one minute on the
Timekeeping Mode screen when the alarm time is reached. You can clear the
reminder text display by pressing A, B, or D, or by exiting the Timekeeping
Mode.
• In the case of the snooze alarm, the reminder text appears on the Timekeeping
Mode screen for the initial alarm operation only.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
Changing the DST setting of the Home City code in the World Time Mode
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D and B to select an alarm.
Alarm on indicator
2. Press A to toggle it on and off.
• Turning on a alarm (AL1to AL4, or SNZ) displays
the alarm on indicator (
) on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that is currently turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator (
) flashes while the
snooze alarm is sounding and during the
5-minute intervals between alarms.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D and B to select the Hourly
Time Signal (SIG).
2. Press A to toggle it on (ON) and off (OFF).
• The Hourly Time Signal on indicator (
) is shown on
the display in all modes while this function is turned on.
Screen
To do this:
Do this:
0:15
Change the hours or minutes
Use D (+) and B (–).
Toggle auto-repeat on (ON) and off (OFF)
Press D.
OFF
• To specify a countdown start time of 24 hours, set 0:00.
4. Press A to exit the setting screen.
• The auto-repeat on indicator ( ) appears on the display while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
Stopwatch
Seconds
Hours
Minutes
1/100 second
Stop
Start
Split
Start
(
Seconds
Stop
Clear
Split release
Stop
Clear
Clear
displayed)
Two Finishes
Start
Split
Stop
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
• The time on the screen may not appear to stop immediately when you press a
button to stop timing or to perform a split operation. Despite this, the time recorded
by your button operation is accurate.
Backlight
Countdown Timer
You can set the countdown timer within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• The initial default countdown start time when you
purchase the watch or after you have its battery
replaced is 15 minutes.
• Countdown timer functions are available in the
Countdown Timer Mode, which you can enter using C.
Re-start
Split Time
Hourly time signal on
indicator
Minutes
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Auto light switch on
indicator
Hours
Auto-repeat
Minutes
The backlight uses an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch automatically turns on
the backlight when you angle the watch towards your
face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Backlight Precautions” for other important
information about using the backlight.
To turn on the backlight manually
In any mode, press L to illuminate the display for about
one second.
• The above operation turns on the backlight regardless of
the current auto light switch setting.
Module 2821
Timekeeping Mode time
3
Operation Guide 2548/2821
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for about one second,
whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes the backlight to turn on.
More than 40 °
Parallel to ground
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
surprise or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down L for about one second to toggle the auto light
switch on (
displayed) and off (
not displayed).
• With Module 2821, the auto light switch on indicator is
.
• The auto light switch on indicator is on the display in all modes while the auto light
switch is turned on.
• In order to protect against running down the battery, the auto light switch
automatically turns off approximately six hours after you turn it on. Repeat the above
procedure to turn the auto light switch back on if you want.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
World Time
• The current time in all World Time Mode cities is calculated in accordance with the
Greenwich Mean Time (GMT) differential for each city, based on the current Home
City time setting in the Timekeeping Mode.
• The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
• The GMT differential is the time difference of the time zone where the city is located
from Greenwich Mean Time.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC) data.
Backlight Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight shortens the battery life.
Auto light switch precautions
• Wearing the watch on the inside of your wrist and movement or vibration of your arm
can cause the auto light switch to activate and illuminate the display. To avoid
running down the battery, turn off the auto light switch whenever engaging in
activities that might cause frequent illumination of the display.
More than 15 degrees
too high
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Areas
The following describes the information indicated by the three graphic areas in each
mode.
• In the Timekeeping Mode, World Time Mode, and Alarm Mode, the graphic areas
indicate the passage of each minute and second of the current time (Timekeeping
Mode time).
• In the e-DATA MEMORY Mode, the graphic areas indicate the number at the
flashing digit during password input.
• In the Countdown Timer Mode, the graphic areas indicate the passage of each
minute and second of the countdown.
• In the Stopwatch Mode, the graphic areas indicate the passage of each second and
1/10 second of the elapsed time.
Minutes
Seconds
Input number
Timekeeping Mode
Seconds
e-DATA MEMORY Mode
• The backlight may not light if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• The backlight turns off in about one second, even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If the backlight
does not light, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back
toward you again. If this does not work, drop your arm
all the way down so it hangs at your side, and then bring
it back up again.
• Under certain conditions, the backlight may not light until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Character List
1/10 seconds
Stopwatch Mode
Inputting Text
The following describes how to input text in the e-DATA
MEMORY and Alarm Modes.
Cursor
To input characters
1. When the cursor is on the display, use D and B to
cycle through the available letters, numbers and
symbols, in the sequence shown below.
Press
.
to
(lower-case)
(space)
to
(symbol)
Press
City Code Table
.
to
(upper-case)
to
(number)
2. When the character you want is at the cursor position, press C to move the cursor
to the right.
3. Repeat steps 1 and 2 to input the rest of the characters you want.
• See the “Character List” for information about the characters you can input.
Auto Return Features
• If you leave the watch in the e-DATA MEMORY or Alarm Mode for two or three
minutes without performing any operation, it automatically changes to the
Timekeeping Mode.
• If you leave a screen with flashing digits or a cursor on the display for two or three
minutes without performing any operation, the watch automatically exits the setting
screen. Except for password input, any settings you have made up to that point are
saved automatically.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
Initial Screens
When you enter the e-DATA MEMORY, World Time, or Alarm Mode, the data you were
viewing when you last exited the mode appears first.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2039.
City
Code
–11
HNL
ANC
Honolulu
Anchorage
LAX
Los Angeles
DEN
Denver
–07.0
CHI
Chicago
–06.0
NYC
New York
–05.0
City
CCS
Caracas
RIO Rio De Janeiro
–2
–1
GMT
LON
London
PAR
Paris
CAI
JRS
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
Cairo
Jerusalem
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
HKG
Hong Kong
GMT
Differential
–11.0
–10.0
–09.0
–08.0
–04.0
–03.0
–02.0
–01.0
+00.0
+01.0
+02.0
+03.0
+03.5
+04.0
+04.5
+05.0
+05.5
+06.0
+06.5
+07.0
+08.0
TYO
Tokyo
+09.0
ADL
Adelaide
+09.5
SYD
Sydney
+10.0
NOU
Noumea
+11.0
WLG
Wellington
+12.0
*Based on data as of June 2003.
Other major cities in same time zone
Pago Pago
Papeete
Nome
San Francisco, Las Vegas, Vancouver, Seattle/Tacoma,
Dawson City
El Paso, Edmonton
Houston, Dallas/Ft. Worth, New Orleans,
Mexico City, Winnipeg
Montreal, Detroit, Miami, Boston, Panama City,
Havana, Lima, Bogota
La Paz, Santiago, Pt. Of Spain
Sao Paulo, Buenos Aires, Brasilia, Montevideo
Praia
Dublin, Lisbon, Casablanca, Dakar, Abidjan
Milan, Rome, Madrid, Amsterdam, Algiers,
Hamburg, Frankfurt, Vienna, Stockholm, Berlin
Athens, Helsinki, Istanbul, Beirut, Damascus,
Cape Town
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi, Moscow
Shiraz
Abu Dhabi, Muscat
Male
Mumbai, Kolkata
Colombo
Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Beijing, Taipei, Manila,
Perth, Ulaanbaatar
Seoul, Pyongyang
Darwin
Melbourne, Guam, Rabaul
Pt. Vila
Christchurch, Nadi, Nauru Is.
4