Casio 2888 Watch User Manual

MO0407-EA
Operation Guide 2888
About This Manual
• Button operations are indicated using the letters shown
in the illustration. Keypad keys are indicated by their
main keycap markings within square brackets in bold,
such as [2].
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Keypad
General Guide
Calculator Mode
Alarm Mode
• Press B to change from mode to mode.
• In any mode, press L to illuminate the display.
▲
▲
Data Bank Mode
Timekeeping Mode
▲
▲
Stopwatch Mode
Dual Time Mode
▲
▲
Press B.
Timekeeping
Hour : Minutes
Seconds
Day of week
Use the Timekeeping Mode to set the time and date. You
can also view the Dual Time Mode screen or Data Bank
Mode screen from the Timekeeping Mode.
Note
This watch is capable of displaying text for the day of the
week in any one of 13 different languages (English,
Portuguese, Spanish, French, Dutch, Danish, German,
Italian, Swedish, Polish, Romanian, Turkish, and
Russian).
Year Month–Day
PM indicator
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds digits start to flash. This is the setting screen.
2. Use C and B to move the flashing in the sequence
shown below to select other settings.
Language indicator
llll
llll
llll
llll
Press C.
Seconds
Press B.
Year
Minutes
Month
Hour
Day
Language
• The currently selected language indicator flashes on the display while the
Language setting is selected in the above sequence.
3. When the setting you want to change is flashing, use the keypad to change it as
described below.
• You must input two digits for the hour, minutes, year, month, and day settings. If
you want to specify 3 o’clock, for example, input 03 for the hour. For the year
setting, input the two rightmost digits.
To do this:
Reset the seconds to 00
Change the year, month,
day, hour, or minutes
Change the language
Do this:
Press [0].
Input values on the keypad keys.
• The flashing moves to the right each time you
input a value.
• While the hour or minutes is flashing (12-hour
timekeeping only), press [=PM] to toggle between
AM (A indicator) and PM (P indicator).
Use [+] and [÷].
• While the language indicator is flashing on the display, use [+] and [÷] to cycle
through the language indicators as shown below until the one for the language
you want to select is displayed.
[+] Indicator Language Indicator Language Indicator Language
ENx
POR
ESP
FRA
[÷] NED
English
Portuguese
Spanish
French
Dutch
DAN
DEU
ITA
SVE
POL
Danish
German
Italian
Swedish
Polish
RO
T)R
PUC
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press C to toggle between 12-hour timekeeping (indicated
by A or P on the display), or 24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
Holding down C for about two seconds in the
Timekeeping Mode toggles between Daylight Saving Time
(DST displayed) and Standard Time (DST not displayed).
• Note that pressing C in the Timekeeping Mode also
toggles between 12-hour timekeeping and 24-hour
timekeeping.
• The DST indicator appears on the Timekeeping and
Alarm Mode displays to indicate that Daylight Saving
Time is turned on.
To display the Dual Time screen and Data Bank screen in the Timekeeping Mode
Holding down [÷] in the Timekeeping Mode displays the Dual Time screen. Holding
down [+] displays the record you were viewing when you last used the Data Bank
Mode.
Hold down [÷]
Dual Time Screen
Data Bank Screen
Data Bank
Remaining number
of records
Name
Romanian
Turkish
Russian
4. Press A to exit the setting screen.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
• See the “Day of the Week List” for information on abbreviations used.
• In addition to the day of the week display, the language setting also affects the type
of characters you can input for the name in the Data Bank Mode.
• Holding down A in the Timekeeping Mode displays the indicator for the currently
selected language. Keeping A depressed for one second changes to the
Timekeeping Mode setting screen (indicated by the flashing seconds digits). If you
accidentally display the setting screen, press A again to exit.
Hold down [+]
Telephone number
The Data Bank Mode lets you store up to 25 records,
each containing name and telephone number data.
Records are automatically sorted based on the characters
of the name. You can recall records by scrolling through
them on the display.
• The characters you can input for the name depend on the
language you select in the Timekeeping Mode. See “To
set the time and date” for more information. Changing the
language setting does not affect names that are already
stored.
• All of the operations in this section are performed in the
Data Bank Mode, which you enter by pressing B.
• Holding down [=PM] in the Data Bank Mode displays
the number of remaining records.
Creating a New Data Bank record
When creating a new Data Bank record, you can input the name and then the
telephone number, or you can input the telephone number and then the name. Being
able to input the phone number first helps to avoid forgetting a number as you input
the name.
1
Operation Guide 2888
Calculator
||
You can use the Calculator Mode to perform arithmetic calculations, as well as
currency conversion calculations. You can also use the Calculator Mode to turn the
input tone on and off.
• All of the operations in this section are performed in the Calculator Mode, which you
enter by pressing B.
• Before starting a new calculation or currency conversion operation in the Calculator
Mode, first use C to display one of the screens shown below.
Press C.
▲
▲
||
To input the name and then the phone number of new Data Bank record
1. In the Data Bank Mode, press C to display the new
Name area
record screen.
• The new record screen is the one that is blank
(contains no name and telephone number).
• If the new record screen does not appear when you
press C, it means that memory is full. To store
Number area
another record, you will first have to delete some of
New Record Screen
the records stored in memory.
2.
Hold
down A until the flashing cursor (_) appears in
|
|
|
the name area of the display. This is the record input
screen.
Timekeeping
Mode time
Value input area
||
Calculator Screen
(space)
[÷]
A to Z
(alphabet)
@ to (symbol)
0 to 9
(number)
• The above character sequence is for English input. See “Character List” for the
character sequences of other languages.
4. When the character you want is at the cursor position, press C to move the cursor
to the right.
5. Repeat steps 3 and 4 until the name is complete.
• You can input up to eight characters for the name.
6. After you input the name, press C as many times as necessary to move the cursor
to the number area.
• When the cursor is located at the eighth space of the name area, moving the
cursor to the right causes it to jump to the first digit of the number. When the
cursor is at the 15th digit of the number, moving it to the right (by pressing C)
causes it to jump to the first character in the name.
• Pressing C moves the cursor the right, while B moves it to the left.
7. In the number area, use the keypad to input the telephone number.
• Each time you input a digit, the cursor automatically moves to the right.
• The number area initially contains all hyphens. You can leave the hyphens or
replace them with numbers or spaces.
• Use [.SPC] to input a space and [–] to input a hyphen.
• If you make a mistake while inputting numbers, use C and B to move the cursor
to the location of the error and input the correct data.
• You can input up to 15 digits for the number.
8. Press A to store your data and exit the Data Bank record input screen.
• When you press A to store data, the name and number you input flash for about
one second as Data Bank records are sorted. After the sort operation is complete,
the Data Bank record screen appears.
• The name can show only three characters at a time, so longer text scrolls
continuously from right to left. The last character is indicated by the symbol s after it.
lll
lll
To input the telephone number and then the name of new Data Bank record
1. In the Data Bank Mode, press C to display the new
Name area
record screen.
2. Use the keypad to input the telephone number.
• Pressing a number key as the first input in a new Data
Bank record will input the number at the first position
of the number area, and automatically move the
Number area
cursor to the next position to the right. Input the rest of
New Record Screen
the phone number.
• Use [.SPC] to input a space and [–] to input a
hyphen.
• If you make a mistake while inputting the phone
ll l
number, press C. This will return to the blank new
record screen, so you can restart your input.
lll
• If you do not input anything for about two or three minutes, or if you press B, the
watch will exit the input screen and change to the Timekeeping Mode. Anything
you have input up to that point will be cleared.
3. After inputting the telephone number, hold down A until the flashing cursor (_)
appears in the name area of the display. This is the record input screen.
4. Input the name that goes with the number.
• Use [+] and [÷] to cycle through the characters at the cursor position. Use C
and B to move the cursor. For details about character input, see steps 3 through 5
under “To input the name and then the phone number of new Data Bank record”.
5. After inputting the name, press A to store your data and exit the Data Bank record
input screen.
To recall Data Bank records
In the Data Bank Mode, use [+] (+) and [÷] (–) to scroll through Data Bank records
on the display.
• See “Sort Table” for details on how the watch sorts records.
• Pressing [+] while the last Data Bank record is on the display displays the new
record screen.
To delete a Data Bank record
1. In the Data Bank Mode, use [+] (+) and [÷] (–) to scroll through the records and
display the one you want to delete.
2. Hold down A until the flashing cursor appears on the display. This is the record
input screen.
3. Press B and C at the same time to delete the record.
• CLR appears to indicate that the record is being deleted. After the record is
deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Data Bank record screen.
Performing Arithmetic Calculations
You can perform the following types of arithmetic calculations in the Calculator Mode:
addition, subtraction, multiplication, division, arithmetic constants, powers, and
approximate values.
To perform arithmetic calculations
When the calculator screen is displayed in the Calculator
Operator area
Mode, you can use the keypad to input calculations just as
Operator symbol you do with any standard calculator. See the examples
below for details.
• Be sure to press C to clear the arithmetic calculator
screen to zero before beginning each calculation. If the
screen is already cleared, pressing C will switch to the
currency converter screen.
Value input area
• While you are inputting a calculation, values are
displayed in the value input area, and operators are
displayed in the operator area of the display.
Example
Display
Operation
(Basic Calculation)
12.3 + 74 - 90 = -3.7
[1] [2] [.SPC] [3] [+] [7] [4][–] [9] [0]
[=PM]
(12 - 0.5) × 3 ÷ 7
=4.9285714
×] [3] [÷] [7] [=PM]
[1] [2] [–] [.SPC] [5] [×
x3 &
4 9285&14
(Constant Calculation)
10 + 7 = 17
12 + 7 = 19
[7] [+] [+] [1] [0] [=PM]
[1] [2] [=PM]
+K
+K
(2.3)4 = 27.9841
×] [×
×] [=PM] [=PM] [=PM]
[2] [.SPC] [3] [×
XK
1&
19
2& 9841
• To perform a constant calculation, input the value you want to use as a constant and
then press one of the arithmetic operator keys twice. This makes the value you input
a constant, which is indicated by the n indicator next to the operator symbol.
• An E (error) indicator will appear whenever the result of a calculation exceeds 8
digits. Press C to clear the error indicator. After that, you will be able to continue the
calculation using an approximate result.
• The following table describes how to correct input errors and how to clear the
calculator after you finish using it.
When you need to do this:
Correct or change the value you are
currently inputting, without deleting the
part of the calculation you have input up
to the current value
Correct or change the arithmetic operator
(+, –, ×, ÷) you have just input
Completely clear the calculation you are
inputting
Clear a displayed calculation result
(produced by pressing the [+], [–],
×], [÷], or [=PM] key) and its
[×
calculation
Perform this key operation:
Press C to clear the displayed value
and return to the 0 display. Next, input
the value you want.
Without pressing C, press the key for
the correct arithmetic operator.
Press C to clear the displayed value
and return to the 0 display. Next, press
C again.
Press C.
Currency Conversion Calculations
You can register a single currency exchange rate for quick and easy conversion to
another currency.
• The default conversion rate is × 0 (multiply the input value by 0). × represents the
multiplication operator and 0 is the exchange rate. Be sure to change the value to
the exchange rate value and the operator (multiplication or division) you want to use.
To change the exchange rate and the operator
1. While the currency converter screen is displayed in the
Operator symbol
Calculator Mode, hold down A until the exchange rate
starts to flash on the display. This is the setting screen.
l lll
2. Use the keypad to input the exchange rate and the
×]or [÷]) you want to use.
operator ([×
• To clear the displayed exchange rate to zero, press
C.
Exchange rate
3. Press A to exit the setting screen.
lll
To edit a Data Bank record
1. In the Data Bank Mode, use [+] (+) and [÷] (–) to scroll through the records and
display the one you want to edit.
2. Hold down A until the flashing cursor appears on the display. This is the record
input screen.
3. Use C (right) and B (left) to move the flashing to the character you want to
change.
4. Use the keypad to change the character.
• For details about character input, see steps 3 (name input) and 7 (number input)
under “To input the name and then the phone number of new Data Bank record”.
5. After making the changes that you want, press A to store them and exit the Data
Bank record input screen.
How the C button affects the current screen in the Calculator Mode
• Pressing C while the current screen (arithmetic calculator or currency converter
screen) shows a value other than zero will clear the screen to zero, without changing
to the other screen.
• Pressing C while an E (error) indicator is displayed clears the E (error) indicator,
but does not clear the current calculation to zero.
• Pressing C while the current screen (arithmetic calculator or currency converter
screen) is cleared to zero, will switch to the other screen.
llll
[+]
Currency Converter Screen
• Arithmetic and currency conversion calculation input and result values can be up to
eight digits for positive values, and seven digits for negative values.
• Exiting the Calculator Mode causes all currently displayed values to be cleared.
llll
3. In the name area, use [+] and [÷] to cycle through characters at the cursor
position. The characters cycle in the sequence shown below.
To check the current exchange rate and operator setting
1. While the currency converter screen is displayed in the Calculator Mode, hold down
A until the exchange rate starts to flash on the display. This is the setting screen.
• The setting screen will also show the current exchange rate and operator setting.
2. Press A to exit the setting screen.
2
Operation Guide 2888
To perform a currency conversion calculation
1. While the currency converter screen is displayed in the Calculator Mode, use the
keypad to input the value from which you want to convert.
2. Press [=PM] to display the conversion result.
3. Press C to clear the conversion result.
• An E (error) indicator appears on the display when the result of a calculation
exceeds 8 digits. Press C to clear the error indicator.
• Pressing [=PM] while a calculation result is displayed will apply the conversion rate
again to the displayed value.
Turning the Input Tone On and Off
An input tone causes the watch to beep each time you press a button or keypad key.
You can turn off the input tone if you want.
• The input tone on/off setting you select in the Calculator Mode is applied to all other
modes, except the Stopwatch Mode.
• Note that alarms will continue to sound even if the input tone is turned off.
To turn the input tone on and off
While the calculator screen or currency converter screen
MUTE indicator
is displayed in the Calculator Mode, hold down C for
about two seconds to toggle the input tone on (MUTE
indicator not displayed) and off (MUTE indicator
displayed).
• Holding down C will also switch the Calculator Mode
screen.
• The MUTE indicator is displayed in all modes when the
input tone is turned off.
Alarms
Alarm number
Alarm time
Timekeeping
Mode time
Alarm date
Alarm Screen
You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
• There are five alarm screens numbered 1 through 5.
The Hourly Time Signal screen is indicated by :00.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm tone operation is performed a
total of seven times, every five minutes, until you turn the alarm off or change it to a
one-time alarm.
• Pressing any button or key stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the alarm 1 setting screen
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
• Pressing C also toggles the currently display alarm or the Hourly Time Signal on
and off.
To turn alarms 2 through 5 and the Hourly Time Signal on and off
1. In the Alarm Mode, use [+] and [÷] to select a onetime alarm (alarms 2 through 5) or the Hourly Time
Hourly time signal
Signal.
on indicator
2. Press C to toggle it on and off.
• The current on/off status of alarms 2 through 5 is
shown by indicators along the bottom of the displays
(al-2 through al-5). The SIG indicator shows the on (SIG
displayed)/off (SIG not displayed) status of the Hourly
Time Signal.
Alarm 2 on Alarm 4 on
• The alarm on indicators and Hourly Time Signal on
indicator
indicator
indicator are displayed in all modes.
• While an alarm is sounding, the applicable alarm on
indicator flashes on the display.
To select the operation of alarm 1
1. In the Alarm Mode, use [+] and [÷] to select alarm 1.
2. Press C to cycle through the available settings in the
sequence shown below.
SNZ indicator and alarm 1 on indicator
Press C.
SNZ al-1
SNZ
indicator
Alarm 1 on
indicator
Hourly Time Signal Screen
Timekeeping
Mode time
Seconds
Hours
Press [+]
AM indicator
Hour : Minutes
lllll
lll lll
l ll
lll
Month – Day
Press [÷]
x1
x2
x3
:00
x5
x4
• You can configure alarm 1 as a snooze alarm or a
one-time alarm. Alarms 2 through 5 can be used as
one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the left
hour setting of the alarm time starts to flash, which
indicates the setting screen.
• This operation automatically turns on the alarm.
3. Use the keypad to input the alarm time and date.
• The flashing automatically advances to the right each time you input a number.
You can also use B and C to move the flashing between input digits.
• To set an alarm that does not use a month and/or day setting, input 00 for each
of the unused settings.
• If you are using 12-hour timekeeping, press [=PM] while the hour or minute
setting is flashing to toggle between AM and PM.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as am (A indicator) or pm (P indicator).
4. Press A to exit the setting screen.
• Note that the month and day setting each appear as 00 on the setting screen when
no month or day is set. On the alarm screen, however, an unset month is shown as
x and an unset day is shown as xx. See the sample displays under “To set an
alarm time”.
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The elapsed time measurement operation continues
even if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
Minutes
1/100 second
To set an alarm time
Alarm number
One-time alarm on
Stopwatch
Note
The 12-hour/24-hour format of the alarm time matches the format you select in the
Timekeeping Mode.
1. In the Alarm Mode, use [+] and [÷] to scroll through
the alarm screens until the one whose time you want to
set is displayed.
al-1
Alarm off
• The SNZ indicator and alarm 1 on indicator (al-1) are
displayed in all modes.
• The SNZ indicator flashes during the 5-minute intervals
between alarms.
• The alarm indicator (al-1 and/or SNZ) flashes while the
alarm is sounding.
Alarm Types
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
Snooze alarm on
To measure times with the stopwatch
Elapsed Time
C
Start
Split Time
C
Start
➤C
Stop
➤C
Re-start
➤C
Stop
➤A
Clear
➤A
Split
➤A
Split release
➤C
Stop
➤A
Clear
➤C
Stop
➤A
➤A
(SPL displayed)
Two Finishes
C
Start
➤A
Split
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Split release
Clear
Display time of
second runner.
3
Operation Guide 2888
Dual Time
Reference
Dual time
(Hour : Minutes Seconds)
Timekeeping
Mode time
The Dual Time Mode lets you keep track of time in a
different time zone. You can select Standard Time or
Daylight Saving Time for the Dual Time Mode time, and a
simple operation lets you view the Timekeeping Mode or
Data Bank Mode screen.
• The seconds count of the Dual Time is synchronized
with the seconds count of the Timekeeping Mode.
• All of the operations in this section are performed in the
Dual Time Mode, which you enter by pressing B.
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display
Auto Display continually changes the contents of the
digital display.
To turn off Auto Display
Press A, B, or C to turn off Auto Display. This returns
to the Timekeeping Mode.
To set the Dual Time
1. In the Dual Time Mode, hold down A until the left hour
setting start to flash, which indicates the setting screen.
2. Use the keypad to input the dual time.
• The flashing automatically advances to the right each
time you input a number. You can also use B and C
to move the flashing between input digits.
• If you are using the 12-hour timekeeping format, press
[=PM] to toggle between AM and PM.
3. Press A to exit the setting screen.
ll l l ll
lllll
llll
lll
To toggle Dual Time Mode time between DST and Standard Time
Holding down C for about two seconds in the Dual Time
Mode toggles between Daylight Saving Time (DST
displayed) and Standard Time (DST not displayed).
• The DST indicator on the display indicates that Daylight
Saving Time is turned on.
To turn on Auto Display
Hold down B for about two seconds until the watch
beeps.
• Note that Auto Display cannot be performed while a
setting screen is on the display.
Auto Return Features
• The watch automatically returns to the Timekeeping Mode if you do not perform any
operation under the conditions described below.
– For two or three minutes in the Data Bank or Alarm Mode
– For six or seven minutes in the Calculator Mode
• If you do not perform any operation for two or three minutes while a setting or input
screen (one with flashing digits or a cursor) is displayed, the watch will automatically
exit the setting or input screen.
• After you perform any button or key operation (except for L) in any mode, pressing
B returns directly to the Timekeeping Mode.
Scrolling
To display the Timekeeping screen and Data Bank screen in the Dual Time Mode
Holding down [÷] in the Dual Time Mode displays the Timekeeping screen. Holding
down [+] displays the record you were viewing when you last used the Data Bank
Mode.
Hold down [÷]
Hold down [+]
The B and C buttons, and [+] and [÷] keys are used in various modes and setting
screens to scroll through data on the display. In most cases, holding down these
buttons during a scroll operation scrolls through the data at high speed.
Initial Screens
When you enter the Data Bank, Calculator, or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
Timekeeping
Timekeeping Screen
Data Bank Screen
Illumination
Auto light switch on
indicator
The display of the watch is illuminated by an LED (lightemitting diode) and a light guide panel for easy reading in
the dark. The watch’s auto light switch automatically turns
on illumination when you angle the watch towards your
face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• You can specify 1.5 seconds or 3 seconds as the
illumination duration.
• See “Illumination Precautions” for other important
information about using illumination.
To turn on illumination manually
In any mode, press L to illuminate the display.
• The above operation turns on illumination regardless of the current auto light switch
setting.
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
Illumination Precautions
•
•
•
•
Keypad keys are disabled and do not input anything while the display is illuminated.
Illumination may be hard to see when viewed under direct sunlight.
Illumination automatically turns off whenever an alarm sounds.
Frequent use of illumination shortens the battery life.
Auto light switch precautions
• Wearing the watch on the inside of your wrist and movement or vibration of your arm
can cause the auto light switch to activate and illuminate the display. To avoid
running down the battery, turn off the auto light switch whenever engaging in
activities that might cause frequent illumination of the display.
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off after the preset illumination
duration (see “To specify the illumination duration”), even
if you keep the watch pointed towards your face.
More than 15 degree
too high
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wist.
Parallel to
ground
More than
40°
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down L for about two seconds to toggle the auto light
switch on (auto light switch on indicator displayed) and off (auto light switch on
indicator not displayed).
• In order to protect against runnning down the battery, the auto light switch will turn
off automatically approximately six hours after you turn it on. Repeat the above
procedure to turn the auto light switch back on if you want.
• The auto light switch on indicator is on the display in all modes while the auto light
switch is turned on.
llll
Day of the Week List
ENx
POR
ESP
FRA
NED
DAN
DEU
ITA
SVE
POL
ROo
TgR
RUS
Sunday
SUN
DOo
DOo
DIo
ZON
SvN
SON
DOo
SiN
NIE
DUo
PAZ
CS
Monday Tuesday Wednesday Thursday
oON
TUE
WED
THU
SEx
TER
QUA
QUI
LUN
oAR
oIb
JUE
LUN
oAR
oER
JEU
oAA
DIN
WOE
DON
oAN
TIR
ONS
TOR
oON
DIE
oIT
DON
LUN
oAR
oER
xIO
owN
TIS
ONS
TOR
PON
WTO
qRO
CZW
LUN
oAR
oIE
JOI
PZT
SAL
mAR
PER
QO
BT
SR
YT
Friday
FRI
SEX
VIE
VEN
VRI
FRE
FRE
VEN
FRE
PIl
VIN
CUo
QT
Saturday
SAT
SaB
SaB
SAo
ZAT
LvR
SAo
SAB
LiR
SOB
Sjo
CTS
SB
llll
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
3 sec. indicator
screen.
2. Press L to toggle the illumination duration setting
between 3 seconds (3 sec. indicator displayed) and 1.5
ll
seconds (3 sec. indicator not displayed).
3. Press A to exit the setting screen.
• The 3 sec. indicator is displayed in all modes when the
illumination duration setting is three seconds.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination does not turn on until about one second after
you turn the face of the watch towards you. This does not indicate malfunction.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
lll
4
Operation Guide 2888
Character List
ENx: (space) A B C D E F x H I J n L o N O P Q R S T U V W X Y Z @ ]
?'.:/+-0123p56q89
POR: (espaço) A ; ( , h B C ^ D E = [ F x H I > J n L o N O ? ] i P
QRSTU@VWXYZ@]?'.:/+-0123p56q89
ESP: (espacio) A ; B C D E = F x H I > J n L o N ` O ? P Q R S T U @
)VWXYZ@]?'.:/+-0123p56q89
FRA: (espace) A ( , B C ^ D E = a [ c F x H I e d J n L o N O ] g P Q
RSTUbf)VWXYZ@]?'.:/+-0123p56q89
NED: (Spatie) A B C D E F x H I J n L o N O P Q R S T U V W X Y Z @
]?'.:/+-0123p56q89
DAN: (Mellemsrum) A B C D E F x H I J n L o N O P Q R S T U V W X Y
Zuvw@]?'.:/+-0123p56q89
DEU: (Leerzeichen) A h B C D E F x H I J n L o N O i P Q R S T U ) V
WXYZ@]?'.:/+-0123p56q89
ITA: (spazio) A ( B C D E = a F x H I j e J n L o N O ? k P Q R S T
UbVWXYZ@]?'.:/+-0123p56q89
SVE: (Mellanslag) A B C D E F x H I J n L o N O P Q R S T U V W X Y Z
whi@]?'.:/+-0123p56q89
POL: (epacja) A l B C m D E n F x H I J n L o o N p O ? P Q R S q T
UVWXYZrs@]?'.:/+-0123p56q89
ROo: (spa iu) A r , B C D E F x H I e J n L o N O P Q R S s T t U V W
XYZ@]?'.:/+-0123p56q89
T)R: (bo luk) A B C ^ D E F x y H I t J n L o N O i P Q R S s T U )
VWXYZ@]?'.:/+-0123p56q89
PUC: (npo en) A B C D E F G * I J K L M o O P Q R S T U V W X Y
bciefh@]?'.:/+-0123p56q89
a
Sort Table
1 (space) 13
2
A
14
3
a
15
4
f
16
5
r
17
6
j
18
7
h
19
8
h
20
9
l
21
10
B
22
11
C
23
12
m
24
m
D
E
b
a
[
c
n
F
x
y
H
25
26
27
28
29
30
31
32
33
34
35
36
I
>
j
e
d
t
J
n
L
o
o
N
37
38
39
40
41
42
43
44
45
46
47
48
p
`
O
?
k
l
i
+
g
P
Q
R
49
50
51
52
53
54
55
56
57
58
59
60
S
q
s
T
t
U
@
b
f
)
V
W
61
62
63
64
65
66
67
68
69
70
71
72
X
Y
Z
r
s
u
v
w
h
i
B
C
73
74
75
76
77
78
79
80
81
82
83
84
D
E
F
c
*
I
J
K
L
M
o
O
85
86
87
88
89
90
P
Q
R
S
T
U
91
92
93
94
95
96
V
W
X
Y
a
97
98
99
100
101
102
b
c
i
e
f
h
103
104
105
106
107
108
@
]
?
'
.
:
109
110
111
112
113
114
/
+
0
1
2
115
116
117
118
119
120
3
p
5
6
q
8
121
9
• Character 7 ( h) is for German, character 69 ( h) is for Swedish.
• Character 43 ( i) is for German and Turkish, character 70 ( i) is for Swedish.
• Characters 71 through 102 are for Russian.
5