Technical information | Casio 3017 Watch User Manual

MO0602-EA
Operation Guide 3017
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Keep the watch exposed to bright light
l
l l l l l l l l l
l
Bright Light
Solar cell
The electricity generated by the solar cell of the watch is
stored by a built-in battery. Leaving or using the watch where
it is not exposed to light causes the battery to run down.
Make sure the watch is exposed to light as much as possible.
• When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright light.
• You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is only partially covered.
• The actual level at which some functions are disabled depends on the watch model.
• Frequent display illumination can run down the battery quickly and require charging.
The following guidelines give an idea of the charging time required to recover from a
single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately 50 minutes exposure to indoor fluorescent lighting
• Be sure to read “Power Supply” for important information you need to know
when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
• See “Power Saving Function” for more information.
About This Manual
• Depending on the model of your watch, display text
appears either as dark figures on a light background, or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light.
Solar cell
(Converts light to
electrical power.)
Battery discharges in the dark.
Bright Light
Electrical
energy
LEVEL 1
LEVEL 2
All
functions
enabled
LEVEL 1
LEVEL 2
Dis- LEVEL 3
charge
LEVEL 3
Charge LEVEL 4
LEVEL 4
Some or all
functions
disabled
Rechargeable battery
World Time Mode
General Guide
▲
Timekeeping Mode
Alarm Mode
▲
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Press C.
Countdown Timer Mode
▲
▲
▲
Stopwatch Mode
Radio-controlled Timekeeping
PM
indicator
Day of week
This watch receives a time calibration signal and updates
its time setting accordingly. The time calibration signal
includes both Standard Time and Daylight Saving Time
(summer time) data.
• This watch is designed to pick up the time calibration
signal transmitted from Mainflingen, Germany and the
signal from Rugby, England.
• In the Timekeeping Mode, you can press A to toggle
the display contents.
Current Time Setting
Hour : Minutes
Seconds
This watch adjusts its time setting automatically in
accordance with a time calibration signal. You can also
perform a manual procedure to set the time and date,
when necessary.
• The first thing you should do after purchasing this watch is to set your Home City,
which is the city where you will use the watch normally. For more information, see
“To set your Home City” below.
• When using the watch outside the range of the time signal transmitter, you have to
adjust the current time setting manually as required. See “Timekeeping” for more
information about manual time settings.
To set your Home City
City code
ll
ll
lll llll
Important!
• Normally, your watch should show the correct time as soon as you select your Home
City code. If it does not, it should adjust automatically after the next auto receive
operation (in the middle of the night). You can also perform manual receive or you
can set the time manually.
• If you are in an area that does not use Daylight Saving Time (summer time), turn off
the DST setting.
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
• Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to
six times a day. When any auto receive is successful, the remaining auto receive
operations are not performed. For more information, see “About Auto Receive”.
• Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive”.
Important!
• When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o’clock side facing towards a window.
Make sure there are no metal objects nearby.
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Use D(east) and B(west) to select the city code you
want to use as your Home City.
• The following are the city codes for major cities in the
Western Europe time zones.
ll l l lll
City
City
Other major cities in same time zone
Code
LIS
Lisbon
Dublin, Casablanca, Dakar, Abidjan
LON London
BCN Barcelona
MAD Madrid
Paris
Amsterdam, Algiers, Hamburg,
MIL
Milan
Frankfurt, Vienna
ROM
Rome
BER
Berlin
STO Stockholm
Helsinki, Istanbul, Beirut, Damascus,
ATH
Athens
Cape Town
Resin Band
Metal Band
• The watch should not be on its side or facing the wrong way.
• Proper signal reception can be difficult or even impossible under the conditions listed
below.
PAR
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances or
office
equipment,
or a mobile
phone
Near a
Near highconstruction
tension
site, airport, or power lines
other sources
of electrical
noise
Among or
behind
mountains
3. Press A to exit the setting screen.
1
Operation Guide 3017
1,500 kilometers
Rugby
Mainflingen
About Auto Receive
The watch receives the time calibration signal automatically up to six times a day.
When any auto receive is successful, the remaining auto receive operations are not
performed. The reception schedule (calibration times) depends on your currently
selected Home City, and whether standard time or Daylight Saving Time is selected
for your Home City.
Note
• Auto receive is turned on whenever LIS, LON, BCN, MAD, PAR, MIL, ROM, BER,
STO, or ATH is selected as the Home City code.
1
2
Auto Receive Start Times
3
4
5
PM indicator
Last Signal Screen
Day of week
Press D.
1:00 am 2:00 am 3:00 am 4:00 am 5:00 am Midnight
BCN, MAD Standard Time
PAR, MIL
ROM, BER
Daylight Saving
STO
(GMT +1) Time
2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am
next day
ATH
Standard Time
(GMT +2)
3:00 am 4:00 am 5:00 am Midnight 1:00 am 2:00 am
next day next day
2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am
next day
3:00 am 4:00 am 5:00 am Midnight 1:00 am 2:00 am
next day next day
4:00 am 5:00 am Midnight 1:00 am 2:00 am 3:00 am
next day next day next day
Note
• Auto receive works only while the watch is in the Timekeeping Mode or World Time
Mode. Auto receive is not performed if an auto receive time is reached while an
alarm is sounding, while a countdown timer operation is in progress, or while a
setting screen (a screen with a flashing setting) is on the display.
• Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
• When auto receive is turned on, the watch receives the calibration signal for two to
five minutes everyday when the Timekeeping Mode time reaches each of the
calibration times. Do not perform any button operation within five minutes before or
after any one of the calibration times. Doing so can interfere with correct calibration.
• Remember that reception of the calibration signal depends on the time kept in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the
Timekeeping Mode time actually is the correct time.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
Receiving indicator
Weak
(Level 0)
To display the Last Signal screen
In the Timekeeping Mode, press D to display the Last Signal screen (indicated by
GET). The Last Signal screen shows the date and time of the last successful time
calibration signal reception.
• In the Timekeeping Mode, you can press A to toggle the display contents.
6
LIS, LON Standard Time
(GMT +0)
Daylight Saving
Time
Daylight Saving
Time
4. Press A to exit the setting screen.
• For information about city codes that support signal receive, see “To set your Home
City”.
Receive time
Hour : Minutes
Seconds
Receive date
Signal Receive Troubleshooting
Check the following points whenever you experience problems with calibration signal
reception.
Problem
Probable Cause
Cannot perform • The watch is not in the Timekeeping
manual receive.
Mode.
• Your current Home City is not one of the
following city codes:
LIS, LON, BCN, MAD, PAR, MIL, ROM,
BER, STO, or ATH.
Auto receive is • You changed the time setting manually.
• The watch was not in the Timekeeping
turned on, but
or World Time Mode, or you performed
the Level 3
some button operation during the auto
receiving
receive operation.
indicator does
• Even if receive is successful, the Level
not appear on
3 receiving indicator disappears from
the display.
the display each day when the first
auto receive operation of the day is
performed.
• Time data (hour, minutes, seconds) only
was received during the last receive
operation. The Level 3 receiving
indicator appears only when time data
and date data (year, month, day) are
both received.
Time setting is • If the time is one hour off, the DST
incorrect
setting may be incorrect.
following signal • The Home City code setting is not
reception.
correct for the area where you are using
the watch.
What you should do
• Enter the Timekeeping Mode
and try again.
• Select LIS, LON, BCN, MAD,
PAR, MIL, ROM, BER, STO,
or ATH as your Home City.
• Perform manual signal receive
or wait until the next auto
signal receive operation is
performed.
• Check to make sure the
watch is in a location where it
can receive the signal.
• Change the DST setting to
Auto DST.
• Select the correct Home City
code.
• For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Timekeeping Precautions”.
World Time
City code
Strong
(Level 3)
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• Following reception of the time calibration signal and calibration of the watch’s time
setting, the Level 3 receiving indicator will remain on the display in all modes. The
Level 3 receiving indicator will not be displayed if signal reception was unsuccessful
or after you adjust the current time setting manually.
• The Level 3 receiving indicator is displayed only when the watch is able to receive
both time and date data successfully. It does not appear when only time data is
received.
• The Level 3 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 3 receiving
indicator is cleared from the display when the first auto receive operation of the day
is performed.
▲
Your City Code
To turn auto receive on and off
1. In the Timekeeping Mode, press D to display the Last
On/Off Status
Signal screen.
2. Hold down A until the receiving indicator and current
auto receive setting (
or
) start to flash. This is
the setting screen.
lllll
• Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press D to toggle auto receive on (
) and off (
).
ll
• This watch is designed to receive the time calibration signal transmitted from
Mainflingen, Germany and the signal from Rugby, England. Signal reception is
possible within the area represented by a circle with a radius of about 1,500
kilometers.
• At distances further than about 500 kilometers from a transmitter, signal reception
may not be possible during certain times of year or times of day. Radio interference
may also cause problems with reception.
• Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• See the information under “Signal Reception Troubleshooting” if you experience
problems with time calibration signal reception.
▲
500 kilometers
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press D.
• If the receive operation is unsuccessful, the message ERR appears on the display
for about one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the Last Signal or ERR screen to the normal
timekeeping screen by pressing D.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
ll
Reception Ranges
To perform manual receive
1. Place the watch on a stable surface so its top (12
o’clock side) is facing towards a window.
Receiving indicator
2. In the Timekeeping Mode, hold down D for about two
seconds until RC! appears on the display.
• Time calibration signal reception takes from two to six
minutes, but some cases it can take as long as 12
minutes. Take care that you do not perform any button
operations or move the watch during this time.
• After signal reception is complete, the display of the
watch changes to the Last Signal screen.
lll l l
• Signal reception is normally better at night than during the day.
• Time calibration signal reception takes from two to six minutes, but some cases it
can take as long as 12 minutes. Take care that you do not perform any button
operations or move the watch during this time.
• When within range of the applicable transmitter, this watch can receive either the
Germany (Mainflingen) or England (Rugby) time calibration signals.
See “Transmitters” for more information.
The World Time Mode shows you the current time in 48
cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
Current time in selected city
To view the time in another city
While in the World Time Mode, press D to scroll through the city codes (time zones)
to the east.
• For full information on city codes, see “City Code Table”.
2
Operation Guide 3017
Countdown Timer
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
• The DST indicator will appear whenever you display a
city code for which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the
DST indicator
currently displayed city code. Other city codes are not
affected.
Alarms
Alarm number
Alarm time
(Hour : Minutes)
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(SIG) on and off.
• There are five alarms numbered AL1 through AL4,
and SNZ. You can configure SNZ as a snooze alarm
only. Alarms AL1 through AL4 can be used as onetime alarms only.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
AL1
AL2
AL3
SIG
SNZ
AL4
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation turns on the alarm automatically.
3. Use C to move the flashing between the hour and
minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting screen.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the snooze alarm setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
Alarm on indicator
2. Press A to toggle the alarm on and off.
• Turning on a one-time alarm (AL1, AL2, AL3,
AL4) displays the alarm on indicator on its Alarm
Mode screen. Turning on the snooze alarm (SNZ)
displays the alarm on indicator and snooze alarm
indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that is currently turned on. When the snooze
alarm is on, the snooze alarm indicator is displayed in all
Snooze alarm indicator
modes.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (SIG).
2. Press A to toggle it on (Hourly Time Signal on
indicator displayed) and off (Hourly Time Signal on
indicator not displayed).
• The Hourly Time Signal on indicator is displayed in all
modes when the Hourly Time Signal is turned on.
Hourly time signal
on indicator
You can set the countdown timer within a range of one to
60 minutes. An alarm sounds when the countdown
reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Seconds
Minutes
1/10 second
To set the countdown start time
1. While the countdown start time is on the display in the Countdown Timer Mode,
hold down A until the current countdown start time starts to flash, which indicates
the setting screen.
• If the countdown start time is not displayed, use the procedure under “To use the
countdown timer” to display it.
2. While a setting is flashing, use D (+) and B (–) to change it.
3. Press A to exit the setting screen.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm sounds for 10 seconds or until
you stop it by pressing any button. The countdown time is reset automatically to its
starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
Stopwatch
Minutes
Seconds
1/100 second
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
D
Start
➤D
Stop
➤D
Re-start
➤D
Stop
➤A
Clear
➤A
Split
(SPL displayed)
➤A
Split release
➤D
Stop
➤A
Clear
➤A
Split
➤D
Stop
➤A
Split release
➤A
Clear
Split Time
D
Start
Two Finishes
D
Start
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Illumination
Auto light switch
indicator
The watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch illuminates the display
automatically when you angle the watch towards your
face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” for other important
information.
To turn on illumination manually
In any mode (except when a setting is on the display),
press B to illuminate the display.
• You can specify 1.5 seconds or 2.5 seconds as the
illumination duration. See “To set the time and date” for
more information.
• The above operation turns on illumination regardless of
the current auto light switch setting.
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on whenever you position
your wrist as described below in any mode. Note that this watch features a “Full Auto
EL Light,” so the auto light switch operates only when available light is below a certain
level. It does not illuminate the display under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you at more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
More than
40°
3
Operation Guide 3017
Warning!
• Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged in
any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not startle or distract others
around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle, or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode, hold down B for about two seconds to toggle the auto light switch on
(auto light switch indicator displayed) and off (auto light switch indicator not displayed).
• The auto light switch indicator remains in all modes while the auto light switch is
turned on.
Power Supply
This watch is equipped with a solar cell and a special rechargeable battery (secondary
battery) that is charged by the electrical power produced by the solar cell. The
illustration shown below shows how you should position the watch for charging.
Solar cell
After a full charge, timekeeping remains enabled for up to about 9 months.
• The following table shows the amount of time the watch needs to be exposed to light
each day in order to generate enough power for normal daily operations.
Exposure Level (Brightness)
Approximate Exposure Time
Outdoor Sunlight (50,000 lux)
5 minutes
Sunlight Through a Window (10,000 lux)
24 minutes
Daylight Through a Window on a Cloudy Day
(5,000 lux)
48 minutes
Indoor Fluorescent Lighting (500 lux)
8 hours
• Since these are the specs, we can include all the technical details.
• Display on 18 hours per day, sleep state 6 hours per day
• 1 illumination operation (1.5 seconds) per day
• 10 seconds of alarm operation per day
• 10 minutes of signal reception per day
• Stable operation is promoted by frequent exposure to light.
Recovery Times
The table below shows the amount exposure that is required to take the battery from
one level to the next.
Exposure Level
Approximate Exposure Time
(Brightness)
Level 5 Level 4 Level 3
Level 2
Level 1
25 hours
7 hours
6 hours
127 hours
35 hours
Daylight Through a Window
on a Cloudy Day (5,000 lux)
11 hours
257 hours
71 hours
Indoor Fluorescent Lighting
(500 lux)
120 hours
2
All functions enabled.
3
Alarm, hourly time signal,
illumination and time calibration
signal reception disabled.
–––
• The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• When setting the time, you can also configure settings for the illumination duration,
the 12/24-hour format, and power saving on/off, and you can specify the screens
that are displayed in the Timekeeping Mode.
• In the Timekeeping Mode, you can press A to toggle the display contents as shown
below.
Day of the Week/Date
PM indicator
Day of week
Month – Day
▲
Press A.
▲
All functions enabled.
▲
2 hours
Sunlight Through a Window
(10,000 lux)
The battery power indicator shows you the current power level of the rechargeable
battery.
Level Battery Power Indicator
Function Status
1
▲
Outdoor Sunlight
(50,000 lux)
Battery Power Indicator and Recover Indicator
Battery power indicator
▲
Important!
• Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Make sure that the watch is normally exposed to bright light
whenever possible.
• This watch uses a special rechargeable battery to store power produced by the solar
cell, so regular battery replacement is not required. However, after very long use, the
rechargeable battery may lose its ability to achieve a full charge. If you experience
problems getting the special rechargeable battery to charge fully, contact your dealer
or CASIO distributor about having it replaced.
• Never try to remove or replace the watch’s special battery yourself. Use of the wrong
type of battery can damage the watch.
• The current time and all other settings return to their initial factory defaults whenever
battery power drops to Level 5 and when you have the battery replaced.
• Turn on the watch’s Power Saving function and keep it in an area normally exposed
to bright light when storing it for long periods. This helps to keep the rechargeable
battery from going dead.
▲
▲
Example: Orient the watch so its face
is pointing at a light source.
• The illustration shows how to position
a watch with a resin band.
• Note that charging efficiency drops
when any part of the solar cell is
blocked by clothing, etc.
• You should try to keep the watch
outside of your sleeve as much as
possible. Charging is reduced
significantly if the face is only partially
covered.
Charging Guide
Hour : Minutes Seconds
Day of the Week/Date
Press D.
▲
▲
Press D.
Last Signal Screen
▲
Press A.
▲
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to a lower temperature.
▲
Time/Date
Charging Precautions
Press D.
Press D.
▲
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it
to become quite hot. Take care when handling the watch to avoid burn injury.
The watch can become particularly hot when exposed to the following
conditions for long periods.
• On the dashboard of a car parked in direct sunlight
• Too close to an incandescent lamp
• Under direct sunlight
Press A.
▲
• The LOW indicator flashes on the display in the Timekeeping Mode when battery is
at Level 3.
• The LOW indicator at Level 3 and the flashing charge indicator (CHG) at Level 4 tell
you that battery power is very low, and that exposure to bright light for charging is
required as soon as possible.
• At Level 5, all functions are disabled and settings return to their initial factory
defaults. Functions are enabled once again after the rechargeable battery is
charged, but you need to set the time and date, after the battery reaches Level 4
(indicated by the flashing charge indicator) from Level 5. You will not be able to
configure any of the other settings until the battery reaches Level 3 (no charge
indicator) after dropping to Level 5.
• Leaving the watch in direct sunlight or some other very strong light source can cause the
battery power indicator to show a reading that is momentarily higher than the actual
battery level. The correct battery power indicator should appear after a few minutes.
• If you use the light or alarms a number of times during a short period, the recover
indicator (RECOV) appears and the following operations become disabled until
battery power recovers.
Illumination
Beeper tone
After some time, battery power will recover and the recover indicator will disappear,
indicating that the above functions are enabled again.
• Pressing D in the Timekeeping Mode will display the Last Signal screen.
▲
|||
▲
Month – Day
Seconds
All functions, including
timekeeping, disabled and
initialized.
▲
5
All functions, including auto
light swich, disabled.
▲
▲
(Charge Soon Alert)
Press A.
▲
|||||
4
|||
Recover indicator
|||||
Day of week
Hour : Minutes
▲
(Charge Soon Alert)
Time/Date
Last Signal Screen
4
Operation Guide 3017
Setting the Time and Date
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the time and date
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C to change the flashing contents in the
sequence shown below to select other settings.
City code
ll
ll
lllll
lllll
City Code
12/24-Hour
Format
DST
Timekeeping Mode Screens
(Day of the Week/Date or Time/Date)
Seconds
Power
Saving
Minutes
Hour
Day
Month
Year
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
Screen:
To do this:
Do this:
Change the city code
Use D (east) and B
(west).
Press D.
Cycle between auto DST (
), Standard
Time (
), and Daylight Saving Time
(
)
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Reset the seconds to
Toggle the illumination duration setting
between 1.5 seconds ( ) and 2.5 seconds
( )
Change the hour, minutes, or year
Press D.
* If you leave the calendar screen displayed for two or three minutes without
performing any operation, the watch will automatically return to the timekeeping
screen.
To specify the Timekeeping Mode screens
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
indicates the setting screen.
2. Press C 10 times so the current Timekeeping Mode screens setting is flashing.
• Day of the Week/Date are selected if the setting screen shows the current date
flashing.
• Time/Date are selected if the setting screen shows “---” flashing in place of
the current date.
3. Press D to toggle the Timekeeping Mode screens between Day of the Week/Date
(current date displayed) and Time/Date ( “---” displayed).
4. Press A to exit the setting screen.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, the alarm,
Hourly Time Signal, and Countdown Timer Mode alarm
all operate normally.
MUTE indicator
Press D.
Press B.
• Since the C button is also the mode change button, holding it down to turn the
button operation tone on or off also causes the watch’s current mode to change.
• The MUTE indicator is displayed in all modes when the button operation tone is
turned off.
Use D (+) and B (–).
Power Saving Function
When turned on, the Power Saving function enters a sleep
state automatically whenever the watch is left in an area
where it is dark for a certain period. The table below
shows how watch functions are affected by the Power
Saving function.
Change the month or day
Toggle Power Saving on (
(
)
) and off
Press D.
Specify Day of the Week/Date or Time/Date Press D.
(indicated by ---) for the Timekeeping
Mode screens.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
indicates the setting screen.
2. Press C and the DST setting screen appears.
3. Use D to cycle through the DST settings in the sequence shown below.
)
DST off (
)
DST on (
6 or 7 days
Blank, with Power Saving
indicator (PS) not flashing
Operation
All functions enabled, except
for the display
Beeper tone, backlight, and
display are disabled.
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
• The watch will not enter the sleep state between 6:00 AM and 10:59 PM. If the
watch is already in the sleep state when 6:00 AM arrives, however, it will remain in
the sleep state.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area.
• Press any button.
• Angle the watch towards your face for reading.
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C nine times until the Power Saving on/off
ll l l l ll
screen appears.
3. Press D to toggle Power Saving on (
) and off
(
).
4. Press A to exit the setting screen.
• The Power Saving indicator (PS) is on the display in all
On/Off status
modes while Power Saving is turned on.
ll
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
The time calibration signal transmitted from Mainflingen and Rugby includes both
Standard Time and DST data. When the Auto DST setting is turned on, the watch
switches between Standard Time and DST (summer time) automatically in
accordance with the received time signal.
• The default DST setting is Auto DST (
) whenever you select LIS, LON, BCN,
MAD, PAR, MIL, ROM, BER, STO, or ATH as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it
probably is best to switch between Standard Time and Daylight Saving Time
(summer time) manually.
Elapsed Time
Display
in Dark
60 to 70 minutes Blank, with Power Saving
indicator (PS) flashing
ll
Daylight Saving Time (DST)
Power saving
indicator
lll l lll
• See “City Code Table” for a complete list of available city codes.
• Auto DST (
) can be selected only while LIS, LON, BCN, MAD, PAR, MIL,
ROM, BER, STO, or ATH is selected as the Home City code. For more
information, see “Daylight Saving Time (DST)” below.
• For information about settings other than the time and date, see the following.
Illumination duration: Illumination
Power Saving: Power Saving Function
Timekeeping Mode Screens (Day of the Week/Date or Time/Date)
4. Press A to exit the setting screen.
Auto DST (
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down C to toggle the button operation tone
on (MUTE not displayed) and off (MUTE displayed).
Auto Return Features
)
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
• If you leave the watch in the Alarm Mode for two or three minutes without performing
any operation, it returns to the Timekeeping Mode automatically.
• If you leave the watch with a flashing setting on the display for two or three minutes
without performing any operation, the watch exits the setting screen automatically.
Timekeeping Mode Screens (Day of the Week/Date or Time/Date)
Scrolling
Use the procedure below to select either Day of the Week/Date or the Time/Date for
the Timekeeping Mode screens.
• In the Timekeeping Mode, you can press A to toggle the display contents as shown
below.
Day of the Week/Date
The B and D buttons are used in various modes and setting screens to scroll
through data. In most cases, holding down these buttons during a scroll operation
scrolls through the data at high speed.
Day of week
Month – Day
Hour : Minutes Seconds
Hour : Minutes
Day of week
Press A.
Seconds
▲
▲
Time/Date
Timekeeping Screen
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Radio-controlled Timekeeping Precautions
Press A.
▲
▲
PM indicator
Month – Day
Calendar Screen
• Strong electrostatic charge can result in the wrong time being set.
• The time calibration signal is bounced off the ionosphere. Because of this, such
factors as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make.
5
Operation Guide 3017
City Code Table
• The watch is designed to update the date and day of the week automatically for the
period January 1, 2000 to December 31, 2099. Setting of the date by a time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
• Though this watch is designed to receive both time data (hour, minutes, seconds)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
• Normally, the signal reception date shown by the Last Signal screen is the date data
included in the received time calibration signal. When only time data is received,
however, the Last Signal screen shows the date as kept in the Timekeeping Mode at
the time of signal reception.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps time within ±15 seconds a month at normal temperature.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your current city code, DST (summer
time), and auto receive settings. The following are the initial factory defaults for these
settings.
Setting
Initial Factory Default
City code
(Berlin)
DST (summer time)
(Auto switching)
Auto receive
(Auto receive)
Transmitters
This watch is designed to receive the time calibration signal transmitted from
Mainflingen, Germany and the signal from Rugby, England. You can configure the
watch to automatically select the transmitter that has the strongest signal.
In this case:
The watch does this:
The first signal auto search operation
1. Checks the Mainflingen signal first.
after factory default settings are in effect, 2. If the Mainflingen signal cannot be
or after the city code has been changed
received, checks the Rugby signal.
Any case other than the above.
1. Checks the last successfully received
signal first.
2. If the last successfully received signal
cannot be received, checks the other
signal.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced or when battery power drops to
Level 5.
• The times for the Timekeeping Mode and all the city codes of the World Time Mode
are calculated in accordance with each city’s UTC differential.
• The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
• The letters “UTC” is the abbreviation for “Universal Time Coordinated”, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the
Earth’fs rotation.
City
Code
City
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
YWG
CHI
MIA
YTO
NYC
CCS
YHZ
YYT
RIO
RAI
LIS
LON
BCN
MAD
PAR
MIL
ROM
BER
STO
ATH
CAI
JRS
MOW
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Winnipeg
Chicago
Miami
Toronto
New York
Caracas
Halifax
St. Johns
Rio De Janeiro
Praia
Lisbon
London
Barcelona
Madrid
Paris
Milan
Rome
Berlin
Stockholm
Athens
Cairo
Jerusalem
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
HKG
Hong Kong
SEL
TYO
ADL
GUM
SYD
NOU
WLG
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
GMT
Differential
–11.0
–10.0
–09.0
Other major cities in same time zone
–08.0
Papeete
Nome
San Francisco, Las Vegas,
Seattle/Tacoma, Dawson City, Tijuana
–07.0
El Paso, Edmonton, Culiacan
–06.0
Houston, Dallas/Fort Worth, New Orleans
–05.0
Montreal, Detroit, Miami, Boston,
Panama City, Havana, Lima, Bogota
–04.0
La Paz, Santiago, Port Of Spain
–03.5
–03.0
–01.0
Sao Paulo, Buenos Aires, Brasilia, Montevideo
+00.0
Dublin, Casablanca, Dakar, Abidjan
+01.0
Amsterdam, Algiers, Hamburg, Frankfurt, Vienna
+02.0
Helsinki, Istanbul, Beirut, Damascus,
Cape Town
+03.0
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi
+03.5
+04.0
+04.5
+05.0
+05.5
+06.0
+06.5
+07.0
Shiraz
Abu Dhabi, Muscat
Male
Mumbai, Kolkata
Colombo
+08.0
Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Beijing, Taipei, Manila, Perth,
Ulaanbaatar
+09.0
Pyongyang
+09.5
Darwin
+10.0
Melbourne, Rabaul
+11.0
+12.0
Port Vila
Christchurch, Nadi, Nauru Island
• Based on data as of June 2005.
12-hour/24-hour Timekeeping Formats
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes.
• With the 12-hour format, the PM indicator (P) appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
Illumination Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• Illumination may be hard to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• The auto light switch is turned off automatically whenever battery power is at Level
4.
• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of
your arm can cause frequent activation of the auto light switch and illumination of the
display. To avoid running down the battery, turn off the auto light switch whenever
engaging in activities that might cause frequent illumination.
• Note that wearing the watch under your sleeve while the auto light switch is turned
on can cause frequent illumination of the display and can run down the battery.
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off after the preset illumination
duration (see “To set the time and date”), even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If illumination
does not turn on, try moving the watch back to the
starting position (parallel with the ground) and then tilt it
back towards you again. If this does not work, drop your
arm all the way down so it hangs at your side, and then
bring it back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
6
Download PDF

advertising