WASHING MACHINE
ZWX 1505 W
ZWX 1605 W
ZWX 1605 W
On/Off
Cottons
Synthetics
Delicates
Wool
95°C
60°C
50°C
40°C
30°C
1200
900
700
500
Rinse Hold
1600 aquacycle 5.5 kg
Prewash
Extra
Quick
40° AA
Start/
Pause
Skip
Prewash
Wash
Rinse
Rinse Hold
Spin
Drain
Filter
End
Reset
Temp.
Spin
Quick Installation Guide:
visit our WEB SITE to view an install video
www.video.uk.electrolux.com
132987021
INSTRUCTION BOOKLET
GB
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.
Installation
●
●
●
●
●
●
●
●
Use
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
Always be sure, that there is no water leakage from
hoses and their connections after the installation.
●
●
●
●
●
●
●
Child Safety
●
●
●
●
●
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
Pets and children have been known to climb into
washing machines. Please check your drum before
use.
The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.
Keep all packaging well away from children.
Keep all detergents in a safe place out of children’s
reach.
●
●
●
●
2
Always unplug the appliance and turn off the water
supply after use.
Do not overload the appliance. See relevant section
in the instruction book.
Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the clothes.
Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.
Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.
Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.
Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.
Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.
As some duvets and eiderdowns should be washed
in large commercial machines because of their bulk,
please check with the manufacturer of the item
before washing in a domestic machine.
Leave the porthole door slightly ajar between washes
to preserve the door seal.
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre. Always insist on genuine spare parts.
Contents
For the User
Maintenance and Cleaning
4
5
5
5
Detergent dispenser drawer
Child safety feature
6-8
The Control Panel
Operating Sequence
Load the laundry
Measure out the detergent
Measure out the fabric softener
Switch the machine on
Select the desired programme/fabric
Select the temperature
Select the spin speed or the Rinse Hold option
Select the desired options
Start the programme
How to change a programme during its cycle
How to cancel a programme during its cycle
How to open the door during the cycle of
a programme
End of programme
Washing Hints
Which detergent?....
And in which form?
Wash Care Symbols
Washing Programmes
Descaling
After each wash
Maintenance Wash
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the pump
Cleaning the water inlet filter
The dangers of freezing
Emergency emptying out
2
Important Safety Information
Your New Washing Machine
Description of the Appliance
9-11
9
9
9
9
9
9
10
10
10
10
10
Something Not Working
Service and Spare Parts
Guarantee Conditions
16-18
16
16
16
16
16
16
16-17
17
17
18
19-20
20
21
For the Installer
Installation Instructions
Technical Specifications
Unpacking
Positioning
Water inlet
Water drainage
Levelling
Special conditions
In the interest of the environment
Electrical connection
10-11
11
12-13
13
13
14
15
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
22
22
23
23
24
24-25
25
25
26
26-27
Your New Washing Machine
Your new washing machine meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption.
Even small loads are washed “economically” because the amount of water used is regulated
automatically according to the load and type of fabric.
●
●
●
Automatic cooling of the wash water to 60°C
before draining, with the 95°C programme. This
reduces thermal shock to fabrics, helping to prevent
creasing.
The special wool programme with its new delicate
wash system treats your woollens with extreme care.
The balance control device ensures that the
washing machine remains stable when spinning.
In the interest of the
environment
●
●
●
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
● Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
● The machine works more economically if it is fully
loaded.
● With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
● Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
●
Materials marked with the symbol
are
recyclable.
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste handling
of this product. For more detailed information about
recycling of this product, please contact your local
city office, your household waste disposal service or
the shop where you purchased the product.
How do we help to protect the environment?
We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed “Something
Not Working”.
4
Description of the Appliance
This new machine meets all modern requirements for effective treatment of laundry with low water, energy and
detergent consumption.
• The possibility of selecting the temperature and all the options offered by this washing machine gives you truly
“customised” washing.
• The automatic cooling of the washing water from 95° to 60°C before draining reduces thermal shock to fabrics,
helping to prevent creasing.
• The ECO valve allows total use of detergent and reduces water consumption so saving energy.
• The balance control device prevents vibration during spinning.
2
1
1
2
3
4
5
Detergent dispenser drawer
Control panel
Door opening handle
Drain pump
Adjustable feet
ZWX 1605 W
On/Off
Cottons
Synthetics
Delicates
Wool
95°C
60°C
50°C
40°C
30°C
1200
900
700
500
Rinse Hold
1600 aquacycle 5.5 kg
Prewash
Extra
Quick
40° AA
Start/
Pause
Skip
Prewash
Wash
Rinse
Rinse Hold
Spin
Drain
Filter
End
Reset
Temp.
Spin
3
4
5
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
C0063
Child safety feature
This machine incorporates a special child safety feature
to prevent small children from being trapped inside the
machine.
To activate this device, rotate the button (without
pressing it) inside the door clockwise until the groove is
horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
P1131
5
The Control Panel
ZWX 1605 W
On/Off
1
Cottons
Synthetics
Delicates
Wool
2
3
95°C
60°C
50°C
40°C
30°C
1600
900
700
500
Rinse Hold
Temp.
Spin
4
5
Prewash
Prewash
Extra
Quick
40° AA
Start/
Pause
Skip
Wash
Rinse
Rinse Hold
Spin
Drain
Filter
End
Reset
6
7
1 “On/Off” button
8
9
IMPORTANT!
By pressing the TEMPERATURE and SPIN SPEED
buttons simultaneously for about 3 secondes, the
acoustic signal is deactivated at the end of the cycle,
when selecting the programmes and in case of an
incorrect option selection .
By pressing these 2 buttons again the acoustic signal
is reactivated.
Press this button to switch the washing machine on.
Press the ON/OFF button again to switch the machine
off.
2 MAINS-ON light
This light is connected to the ON/OFF button. It lights
up when you press the button, and goes out when you
press it again.
5 “Spin” button
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a speed different
from the one proposed by the washing machine. The
relevant light will light up.
Maximum speeds are:
• for cotton: 1600 rpm (ZWX 1605) or 1500 rpm
(ZWX 1505);
• for synthetic fabrics and wool: 900 rpm;for
• for delicate fabrics: 700 rpm.
3 FABRICS button
Press this button repeatedly to select the programme on
the basis of the type of laundry to be washed. The light
relevant to the selected programme will light up. The
washing machine will propose a temperature and
automatically select the maximum spin value provided
for the programme you have chosen. You can change
these values by operating buttons 4 and 5.
“Rinse Hold” position: when you choose this option,
the machine will not drain the water of the last rinse, so
as not to crease the laundry.
At the end of the cycle, the light of the “Start/Pause”
button goes out, the “End” and “Rinse Hold” lights
illuminate to indicate that the water must be drained.
To complete the cycle, first press “Skip/Reset” button
and then choose one of the following options:
4 “Temp.” button
Press this button repeatedly to increase or decrease the
temperature, if you want your laundry to be washed at a
temperature different from the one proposed by the
washing machine. The relevant light will light up.
Maximum temperatures are 95°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics and wool.
• Drain only:
- Press FABRICS button in order to select the desired
programme and press 3 times “Skip/Reset” button
until the “Drain” light illuminates. Then depress
“Start/Pause” button.
6
• Drain and Spin:
- Choose the previously selected programme by means
of the FABRICS button, afterwards change the spin
speed if needed, by means of the “Spin” button and
then press “Skip/Reset” button twice until the ‘Spin”
light illuminates and then depress “Start/Pause”
button.
Important! You must set the washing machine to
Pause before you make any change in the programme
in progress.
8 “Skip/Reset” button
At the end of a programme, you must press this button
once or repeatedly, in order to clear the contents of the
memory; otherwise, the next time you switch the
washing machine on, the audible warning signals
relevant to the end of the previous cycle will be given.
You can also press the “Skip/Reset” button to exclude
one or several phases of the programme which is
running, as indicated below.
6 OPTIONS button
Press this button to select the following options:
● Prewash: select this option if you wish your laundry
to be prewashed before the main wash (not available
for wool).
The prewash ends with a short spin in programmes
for cotton and synthetic fabrics, whereas in the
programme for delicate fabrics the water is only
drained.
● Extra Quick: select this option for laundry that is
only slightly soiled (not for Wool programme).
The washing time will be reduced according to the
type of fabric and the selected temperature.
● 40° AA: this option can be selected for cottons and
synthetics lightly or normally soiled with a
temperature of 40°C or higher.
If you select 40°C together with option 40° AA, the
machine will prolong the time at 40°C in the washing
phase. On cotton programme this will allow an AA
class in energy efficiency and washing performance to
be achieved.
If you select 95°C, 60°C or 50°C and press the
40° AA button, the washing temperature will be
reduced and the washing time will be prolonged.
- set the washing machine to Pause by pressing the
“Start/Pause” button (the relevant light will flash);
- press the “Skip/Reset” button once or several times, until
the required phase(s) is(are) cancelled (the light next to
the symbol of the phase(s) will go out).
Example:
In this case, the spin (at
Prewash
the speed provided for
Wash
the selected type of
Rinse
fabric) will be
Rinse Hold
performed.
Spin
Drain
Filter
End
This button allows you also to select special
programmes, such as Rinse, Spin and Drain.
• If the machine is already switched on because it has
just performed a washing programme, proceed as
follows:
- depress “Skip/Reset” button once or repeatedly to
cancel the previously performed programme (all the
phase indicator lights must be off);
- select the type of fabric by means of the relevant
button;
- select the special programme:
• Rinse and Spin
Depress “Skip/Reset” once, the “Wash” pilot light
goes out.
• Spin
Depress “Skip/Reset” twice, the pilot lights “Wash”
and “Rinse” go out.
The Prewash, the Extra Quick and the 40° AA options
cannot be selected together by means of the relevant
button.
7 “Start/Pause” button
This button has two functions:
• Start: after you have selected the desired programme
and options, press this button to start the washing
machine. The light above the button will stop flashing
and remain lit.
• Pause: when you press this button again, the
programme in progress is interrupted. The light above
the button will start flashing. To restart the
programme, press the button again.
7
9 Programme phase indicator
lights
•Drain
Depress “Skip/Reset” three times, the pilot lights
“Wash”, “Rinse”and “Spin” go out.
When you select a programme, the lights relevant to the
phases that form the programme light up.
Example:
Prewash
Wash
Rinse
Rinse Hold
Spin
Drain
Filter
End
Prewash
In this case the machine
will perform the rinses
and spin.
Wash
Rinse
Rinse Hold
Spin
Drain
Filter
End
After you have started the programme, only the light
relevant to the phase that is currently being carried out
will remain lit.
At the end of the programme the “End “pilot light
illuminates.
If the “Filter” light lights up at the end of the programme
this means that the drain pump is clogged.
In the event of operating problems the “End “pilot light
starts to flash:
1 flash = the machine does not fill
2 flashes = the machine does not empty
4 flashes = the door has not been closed
To eliminate the problem, see paragraph “Something not
working”.
• If the machine is switched off:
- depress “On/Off” button to switch it on;
- select the type of fabric by means of the relevant
button:
- select the special programme as previously
described.
8
Operating Sequence
4.Switch the machine on
Before the first wash we recommend that you pour 2
litres of water into the main wash compartment
of
the detergent drawer in order to activate the ECO valve.
Then run a cotton cycle at 95°C, with the machine
empty, in order to remove any manufacturing residue
from the drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
Press the ON/OFF button to switch the machine on: the
light above the button will light up.
O N / OFF
1.Load the laundry
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
5. Select the desired programme/
fabric
Press the FABRICS button repeatedly, in order to select
the desired programme/fabric. The relevant light will
light up.
The lights relevant to the phases that form the
programme will light up.
The “Start/Pause” button light will start flashing.
P0004
Cottons
Synthetics
Delicates
Wool
2.Measure out the detergent
Pull out the dispenser drawer until it stops. Measure out
the amount of detergent required and pour it into the
main wash compartment
.
If you wish to carry out the prewash, pour detergent into
the appropriate compartment marked
.
6. Select the temperature
3.Measure out the fabric
softener
Press the “Temp.” button if you wish to select a
temperature value different from the one proposed by
the washing machine.
The relevant light will light up.
If required, pour fabric softener into the compartment
marked , without exceeding the «MAX» mark.
95°C
60°C
50°C
40°C
30°C
C0064
Prewash
Wash
Rinse
Rinse Hold
Spin
Drain
Filter
End
Temp.
C0065
Close the drawer gently.
9
7. Select the spin speed or the
RINSE HOLD option
10. How to change an option or
a programme during its cycle
Press the “Spin” button repeatedly, in order to select the
desired spin speed or the Rinse Hold option. The
relevant light will light up.
If you select the Rinse Hold option, the machine will
stop at the end of the programme with the water still in
the tub.
ZWX 1605 W
ZWX 1505 W
Before you make any change, you must pause the
washing machine by pressing the “Start/Pause” button.
It is possible to change any option or temperature before
the programme carries it out.
Changing the type of fabric is possible, obviously, only
during the washing phase and after you have cancelled
the running programme by means of the “Skip/Reset”
button. When you make a change in this parameter, the
washing machine will resume the cycle from the
beginning maintening the water in the drum.
If it is necessary to drain the water in order to change
the programme in progress, proceed as follows:
• Pause the machine by pressing the “Start/Pause”
button;
• press the “Skip/Reset” button repeatedly, until only
the “Drain” light remains lit;
1600
900
700
500
Rinse Hold
Spin
1500
900
700
500
Rinse Hold
Spin
8. Select the desired options
• press the “Start/Pause” button again.
You may now select a new programme and press the
“Start/Pause” button to start it.
If your laundry is very dirty, it may be advisable to
select the Prewash option.
If your laundry is only slightly soiled, select the Extra
Quick option
If your laundry is lightly or normally soiled and it is
necessary to prolong the washing time, select the
40° AA option.
11. How to cancel a programme
during its cycle
To cancel a programme that is being carried out, first
pause the washing machine by pressing the
“Start/Pause” button, then press the “Skip/Reset” button
repeatedly, until the phase indicator lights go out.
Prewash
Extra
Quick
40° AA
12. How to open the door during
the cycle of a programme
You can open the door, after having set the washing
machine to PAUSE, provided the following conditions
exist:
• the washing machine is not in the heating phase
beyond 55°C;
• the level of the water is not high;
• the drum is not turning.
If these requirements are met, when you pause the
washing machine, the door can be opened.
Should it not be possible to open the door, and should it
be absolutely necessary to do so, switch the machine off
by pressing the “On/Off” button.
After approximately 3 minutes, you can open the door.
9. Start the programme
Press the “Start/Pause” button. The relevant light will
stop flashing and only the light relevant to the phase that
is in progress will remain lit.
Start/
Pause
10
Note: when you switch the machine on, if you must
erase the previously performed programme, it is also
sufficient to press the FABRICS button and select a new
programme.
Press the “On/Off” button to switch the machine off.
The relevant light will go out.
Remove the laundry from the washing machine.
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get damaged
in a subsequent wash (e.g. by shrinking) or bleed colour
into another load of laundry.
We advise you to close the water supply tap and
disconnect the plug from the socket.
Leave the door ajar in order to air the washing machine.
Pay attention to the level and temperature of the
water in the washing machine!
When you close the door and press the “On/Off”button
again, the washing machine will resume the programme
from the point where it had been interrupted.
13. End of programme
At the end of the programme, the washing machine
stops automatically and gives an audible signal.
If you had selected the “Rinse Hold option, the light of
the “Start/Pause” button goes off, the phase indicator
lights “Rinse Hold”and “End” illuminate to indicate that
the water must be drained.
To complete the cycle, first press “Skip/Reset” button
and then choose one of the following options:
• Drain only:
- Press FABRICS button in order to select the desired
programme and press 3 times “Skip/Reset” button
until the “Drain” light illuminates. Then depress
“Start/Pause” button.
• Drain and Spin:
- Choose the previously selected programme by means
of the FABRICS button, afterwards change the spin
speed if needed, by means of the “Spin” button and
then press “Skip/Reset” button twice until the ‘Spin”
light goes on and then depress “Start/Pause”button.
When the programme has been completed the audible
signal is given.
Press the “Skip/Reset” button repeatedly to erase the
programme that has just been carried out. If you
omit to do this, the next time you switch the washing
machine on, you will hear the audible signal.
11
Washing Hints
Do NOT overload the machine. Weigh the laundry the
first few times you use the appliance.
●
●
The average weights of the most common items are
listed below as a guide:
●
1000g = 1 kg
●
Sheet
700-1000 g
Pillow case
100-200 g
Tablecloth
400-500 g
Serviette
50-100 g
Tea towel
70-120 g
Linen hand towel
100-150 g
Towelling hand towel
150-250 g
Towelling bath towel
700-1000 g
Bath robe
●
●
1000-1500 g
Man’s shirt
200-300 g
Apron
150-200 g
●
●
●
●
●
●
●
●
●
●
●
●
Load the laundry loosely alternating large items with
small ones.
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
12
Use the correct quantities of detergent.
For wool, use gentle detergent only in small
quantities.
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special presoak product or biological detergent.
Only wool marked “Pure New Wool - washable,
preshrunk” can be washed in the the wool
programme; other types of wool should be washed
by hands.
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Once you have finished using the machine, you are
advised to unplug it and turn off the water tap.
Which detergent?....
And in which form?
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.
Not only are there different types of detergent, but they
are also available in different forms. Whether you chose
a powder or liquid in traditional or compact form is
your own personal choice.
TRADITIONAL POWDERS
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
TRADITIONAL LIQUIDS
WHITES
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol
, start
the machine immediately upon placing the
detergent in the dispenser drawer.
Alternatively the detergent is measured into the
specially designed dosing device* which should be
placed on top of the laundry, and at the back of the
machine drum.
We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.
NON BIOLOGICAL
If you prefer to use a non
biological detergent, which does
not contain enzymes we
recommend Fairy. Fairy provides
good cleaning and stain removal.
COMPACT POWDERS AND LIQUIDS
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which
should be placed on top of the laundry, and at the back
of the machine drum.
COLOUREDS
For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach
and therefore helps to preserve
colours.
* If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
DELICATE ITEMS
FABRIC CONDITIONERS
When washing delicates such as
woollens, you should use a product
which is specially designed to care for
fine fabrics.
Dreft Automatic is suitable for
woollens and other delicates.
These are ideal for improving ‘softness’, and also
reduce static cling on synthetics and make ironing
easier. They are available in two types:
For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The
liquid fabric softener should be
poured into the compartment
marked with the symbol .
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.
LAUNDRY BLEACH
For additional stain removal you may
wish to use a product such as Ace
Gentle Bleach which is used in addition
to your chosen detergent. Ace is
suitable for all washable fabrics
including silks, woollens and coloureds.
Bounce conditioning sheets for use
in a tumble dryer. We recommend
the conditioning sheets are pinned
(using a safety pin) to an article
of laundry and placed in the
tumble dryer.
13
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
95
Normal (Maximum)
White Cotton or Linen
without Special Finishes
60
Normal (Maximum)
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.
50
Reduced (Medium)
Nylon, Polyester/Cotton, Viscose
with Special Finishes,
Cotton/Acrylic Mix.
40
Normal (Maximum)
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
40
Reduced (Medium)
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
40
Much Reduced (Minimum)
Hand wash only
FABRIC
Wool, wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Hot iron
Cotton, Linen, Viscose
Warm iron
Polyester mixtures, Wool
Cool iron
Acrylic, Nylon, Polyester
DRY CLEANING
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
with high heat setting
with low heat setting
May be tumble dried
X
A cross through any symbol means «DO NOT»
Important Notes
fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash programme,
place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing it
in gently. This is particularly important if you are using
14
Washing programmes
Type of
laundry and
symbols on
labels
60
Load
ZWX 1605W
95
White cotton:
5.5 kg
e.g. sheets,
ZWX 1505W
tablecloths,
5.0 kg
household
linen
60
40
ZWX 1605W
30
5.5 kg
Coloured
ZWX 1505W
cotton: e.g.
5.0 kg
shirts, blouses,
underwear,
towels, household linen
60
50
40
30
30
30
Wool
Main wash at
60°-50°-40°30°C
3 rinses
Long spin
Main wash at
Cottons
60°C + 40°AA 60°C
ZWX 1505W
3 rinses
5.0 kg
Long spin
Consumption*
Energy
kWh
Water
litres
Time
h/min.
ZWX 1605W ZWX 1605W ZWX 1605W
2.1
56
2.25
ZWX 1505W ZWX 1505W ZWX 1505W
2.0
53
2.25
SPIN SPEED ZWX 1605W ZWX 1605W ZWX 1605W
RINSE HOLD
1.3
52
2.00
PREWASH
ZWX 1505W ZWX 1505W ZWX 1505W
EXTRA QUICK
1.2
49
2.00
40° AA
SPIN SPEED
RINSE HOLD
ZWX 1605W ZWX 1605W ZWX 1605W
0.93
52
2.26
ZWX 1505W ZWX 1505W ZWX 1505W
0.85
49
2.20
2.5 kg
Synthetics
60°-50°-40°30°C
Main wash at
60°-50°-40°30°C
3 rinses
Short spin
SPIN SPEED
RINSE HOLD
PREWASH
EXTRA QUICK
40° AA
0.9
54
1.29
2.5 kg
Delicates
40°-30°C
Main wash at
40°-30°C
3 rinses
Short spin
SPIN SPEED
RINSE HOLD
PREWASH
EXTRA QUICK
0.5
55
1.00
2 kg
Wool
40°-30°C
Main wash at
40°-30°C
3 rinses
Short spin
SPIN SPEED
RINSE HOLD
0.35
55
0.55
Delicate fabrics: e.g.
acrylic fabrics,
viscose, polyester, synthetic
blends
40
Cottons
60°-50°-40°30°C
Available
options
SPIN SPEED
Main wash at
RINSE HOLD
60°-95°C
PREWASH
3 rinses
EXTRA QUICK
Long spin
40° AA
5.5 kg
Synthetic
fabrics and
blends: e.g.
shirts, blouses,
underwear
40
Cottons
60°-95°C
Description of
programme
ZWX 1605W
40
White and
coloured
cotton: e.g.
shirts, blouses,
underwear,
towels, household linen
60
Programme/
temperature
The “white/coloured cotton programme” at 60°C + 40°AA is the reference programme for the data entered in the
energy label, in compliance with EEC 92/75 standards.
* This data is given purely as an indication: the consumption values may vary in relation to the quantity and type of
laundry, the temperature of the water supply and the ambient temperature. The data refers to the highest temperature
provided for each programme.
15
Maintenance and Cleaning
To aid cleaning, the top part of the additive compartment
should be removed.
Before any maintenance or cleaning is carried out you must
DISCONNECT the appliance from the electricity supply.
Descaling
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
C0066
C0067
C0068
P1086
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
To run a maintenance wash:
● The drum should be empty of laundry.
● Select the hottest cotton wash programme.
● Use a normal measure of detergent, must be a
powder (such as Ariel Futur).
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
External cleaning
Clean the exterior cabinet of the appliance with soap and
water only, and then dry thoroughly.
P0038
Cleaning the dispenser drawer
Cleaning the pump
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
any traces of accumulated powder.
The pump should be inspected if
• the machine does not empty and/or spin
• the machine makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump.
Proceed as follows:
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
16
Warning
When the appliance is in use and depending on the
programme selected there can be hot water in the pump.
Never remove the pump cover during a wash cycle,
always wait until the appliance has finished the cycle,
and is empty. When replacing the cover, ensure it is
securely retightened so as to stop leaks and young
children being able to remove it.
P1114
• Place a container close to the pump to collect any
spillage.
• Pull out the emergency emptying hose, place it in the
container and remove its cap.
• When no more water comes out, unscrew the pump
cover and remove it. Always keep a rag nearby to dry
up spillage of water when removing the cover.
Cleaning the water inlet filter
If your water is very hard or contains traces of lime
deposit, the water inlet filter may become clogged.
It is therefore a good idea to clean it from time to time.
Turn off the water tap. Unscrew the water inlet hose.
Clean the filter using a hard bristle brush.
Tighten up the inlet hose.
P1115
• Remove any objects from the pump impeller by
P1090
rotating it.
The dangers of freezing
If the machine is installed in a place where the
temperature could drop below 0°C, proceed as follows:
• Remove the plug from the socket.
• Close the water tap and unscrew the water inlet hose
from the tap.
• Place the end of the emergency emptying hose and
that of the inlet hose in a bowl placed on the floor and
let water drain out.
• Screw the water inlet hose back on and reposition the
emergency emptying hose after having put the cap on
again.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.
When you use the machine again, make sure that the
ambient temperature is above 0°C.
• Put the cap back on the emergency emptying hose and
place the latter back in its seat.
P1117
• Screw the pump cover fully in.
• Close the pump door.
17
Important!
Every time you drain the water through the emergency
emptying hose you must pour 2 litres of water into the
main wash compartment of the detergent drawer and
then run the special programme “Drain”.
To do this :
• depress the “On/Off” button
to switch the machine
on;
• select a programme by means of the FABRICS
button;
• depress “Skip/Reset” button
three times until only
the “Drain’ light remains lit;
• depress “Start/Pause button .
This will activate the ECO valve allowing a total use of
the detergent in the next wash.
Emergency emptying out
If the water is not discharged, proceed as follows to
empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water
stops flowing out;
• clean the pump if necessary as previously described;
• replace the emergency emptying hose in its seat after
having plugged it;
• screw the pump cover again and close the door.
18
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without
calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed
below.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
During machine operation it is possible that the “End” light starts to flash and at the same time an acoustic signal will
sound:
- 1 flash: problem with the water supply
- 2 flashes: problem with water draining
- 4 flashes: door open
Once the problem has been eliminated, press the START/PAUSE button
to restart the programme. If after all
checks, the problem persists, contact your local Service Force Centre.
Symptom
Possible causes
The machine does not start
●
●
●
●
●
The machine does not fill
●
●
●
●
The machine fills then empties
immediately
●
●
●
The machine does not empty and/or
does not spin
●
●
●
●
●
●
There is water on the floor
●
●
●
●
●
●
Unsatisfactory washing results
●
●
●
●
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no supply at the socket.
The main fuse or the fuse in the plug has blown.
The “Start/Pause” button has not been depressed.
The water tap is closed.
The filter in the inlet hose is blocked.
The inlet hose may be squashed or kinked.
The door has not been closed.
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
The drain hose may be squashed or kinked.
The “Rinse Hold’ option has been selected.
The drain pump may be blocked.
The drain hose extension, if fitted, is not correct. Follow the
instructions for connecting to the waste.
The drainage system pipes are blocked.
The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.
Too much detergent or unsuitable detergent has been used (creates too
much foam).
Check whether there are any leaks from the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if
it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
The cap on the emergency emptying hose has not been replaced after
cleaning the pump.
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct wash programme/temperature has not been selected.
Too much laundry has been placed in the drum.
19
Symptom
Possible causes
The machine vibrates when spinning
●
●
●
●
●
The door will not open
●
●
●
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not level and stable (check diagonally).
The washing load is badly distributed in the drum.
Maybe there is very little laundry in the drum.
The water level is above the bottom edge of the door.
The machine is heating the water.
The drum is turning.
Spinning starts late or the machine
does not spin
●
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume.
If, after 10 minutes, the laundry is still not evenly distributed in the
drum, the machine will not spin. In this case, redistribute the load
manually and select the spin programme.
The machine makes an unusual
noise
●
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor ensures
a softer start and more even distribution of the laundry in the drum
when spinning, as well as increased stability of the machine.
No water is visible in the drum
●
Machines based on modern technology operate very economically
using very little water without affecting performance.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance (found
on the rating plate - see picture)
5. The purchase date.
Please note that a valid purchase receipt or
guarantee documentation is required for inguarantee service calls.
Service & Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk.
For Customer Service in Ireland please contact us at the
address below:
Mo
Pro d. .....
d.
No .....
. .....
.....
.
Ser
. No
. .....
....
Zanussi Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Mod. ..........
Prod. No. ...........
Tel: +353 (0)1 4090751
Email: service.eid@electrolux.ie
P0042 BD
To buy accessories, consumables and spare parts at
our online shop please visit: http://www.zanussielectrolux.co.uk
20
Ser. No. .........
Customer Care Department - Zanussi Electrolux
Major Appliances
Addington Way - Luton - Bedfordshire
LU4 9QQ
Tel 08705 727727*
Customer Care Department
For general enquiries concerning your Zanussi
Electrolux appliance or for further information on
Zanussi Electrolux products, please contact our
Customer Care Department by letter or telephone at the
address below or visit our website at www.zanussi.co.uk
* calls to this number may be recorded for training
purposes.
Guarantee Conditions
Standard guarantee conditions
●
We, Zanussi Electrolux, undertake that if, within 12
months of the date of the purchase, this ZANUSSI
ELECTROLUX appliance or any part thereof is proved
to be defective by reason only of faulty workmanship or
materials, we will, at our option repair or replace the
same FREE OF ANY CHARGE for labour, materials or
carriage on condition that:
● The appliance has been correctly installed and used
only on the electricity supply stated on the rating plate.
● The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.
● The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
● All service work under this guarantee must be
undertaken by a Service Force Centre.
● Any appliance or defective part replaced shall
become the Company’s property.
● This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
●
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:
● The guarantee starts from the date you first
purchased your product.
● The guarantee is for the same period and to the same
extent for labour and parts as exists in the new
country of use for this brand or range of products.
● The guarantee relates to you and cannot be
transferred to another user.
● Your new home is within the European Community
(EC) or European Free Trade Area.
● The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household.
● The product is installed taking into account
regulations in your new country.
Before you move please contact your nearest Customer
Care Centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0) 344 62 29 29
Germany
Nurnberg
+49 (0) 800 234 7378
Italy
Pordenone
+39 0434 39 4700
Sweden
Stockholm
+46 (0) 8 672 53 90
UK
Luton
+44(0) 8705 727 727
Ireland
Dublin
+44 (0)1 4090751
Exclusions
This guarantee does not cover:
●
●
Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
Products of Zanussi Electrolux manufacture which
are NOT marketed by Zanussi Electrolux.
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
21
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Technical Specifications
DIMENSIONS
Height
Width
Depth
POWER SUPPLY VOLTAGE
TOTAL POWER ABSORBED
85 cm
60 cm
59 cm
230-240 V/50 Hz
2050 W (10A)
WATER PRESSURE
Minimum
Maximum
0.05 MPa (0.5 bar)
0.80 MPa (8. bar)
MAXIMUM RECOMMENDED LOAD
Cotton, linen
5.5 kg (ZWX 1605W)
5.0 kg (ZWX 1505W)
Synthetics
2.5 kg
Delicate fabrics
2.5 kg
Wool
2.0 kg
MaximumZ 16 S
1600 rpm (ZWX 1605W)
1500 rpm (ZWX 1505W)
SPIN SPEED
CONSUMPTION DATA FOR WASHING
5.5 KG (ZWX 1605W) and 5 KG
(ZWX 1505W) OF COTTONS
AT 60°C + 40°AA
Energy
Water
ZWX 1605W
0.93 kWh
52 litres
ZWX 1505W
0.85 kWh
49 litres
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
22
Unpacking
Remove the polystyrene base. Set the machine upright
and unscrew the remaining rear screw. Slide out the
relevant pin.
Fill all the holes with the plastic plugs supplied with the
instruction booklet.
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
Using a spanner unscrew and remove the two rear
bottom screws. Slide out the two plastic pins.
Lay the machine gently on its back, making sure that the
hoses are not squashed.
P1128
P0002
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to a suitable existing tap with the
drain hose discharging into a sink.
The appliance has an inlet hose, with female 3/4” BSP
thread connector. If this connection is not compatible
with the plumbing of the existing installation, a variety
of connectors are available from good hardware stores
and plumbers merchants to suit most domestic
plumbing. Any alteration to your existing plumbing
must be carried out by a competent person, or qualified
plumber.
P0001
P1129
Remove the polystyrene block from the bottom of the
machine and release the two plastic bags.
Very carefully slide out the left polythene bag, removing
it towards the right and then downwards.
1
2
3
P1124
P1126
Repeat the operation for the right polythene bag,
removing it towards the left and then upwards.
Carry out the bottom cover placed into the drum of your
appliance, lay its hook as the arrow «A» indicates and
push the top of the cover to seal it closed.
Installation on a Suspended Floor
Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.
A
P1127
P1205
Important!
You can find more detailed instructions regarding the
bottom cover assemblig in its relative bag.
23
Water inlet
Water drainage
Connect the hose to a tap with a 3/4” thread.
Always use the hose supplied with the appliance to
connect to the water supply.
This appliance is designed to be permanently plumbed
into your home's drainage system using one of the
following methods.
1. Into a drainage standpipe.
Firstly form a hook in the end of the drain hose using
the “U” piece” suppl3ied.
P1088
Installation should comply with local water authority
and building regulations’ requirements.
The appliance must be connected to a cold water
supply.
A minimum water pressure of 0.05 MPa (0.5 bar) is
required for safe operation of the appliance.
“U” piece
supplied
P1199
Place the drain hose into your standpipe, which should
have an internal diameter of approximately 38mm thus
ensuring there is an air break between the drain hose
and standpipe.
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
Set the hose correctly by loosening the ring nut. After
positioning the inlet hose, be sure to tighten the ring nut
again to prevent leaks.
30 cm (12")
38 mm (11.2”)
standpipe
diameter
P1200
When discharging into a standpipe ensure that the top of
the standpipe is no more than 90cm (35.4'') and no less
than 60cm (23.6'') above floor level.
3 pin
Max. 90 cm (35.4”)
Min. 60 cm (23.6”)
P0021
P1201
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
24
Levelling
If your drain hose looks like this (see below) you do not
require the “U” piece”. Just push the hose firmly into
the standpipe.
Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable (check diagonally).
P1212
P1051
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before, remove
any blanking plug that may be in place.
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Some vibration is inevitable, especially if mounted on a
wooden floor.
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
Special conditions
P1197
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.
Push the drain hose onto the spigot and secure with a
clip if required, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the sink
entering the washing machine.
Warning
The machine should NOT be placed on deep pile
carpeting.
Loop
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
P1198
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
Important
Before connecting up the machine to new pipework or
to pipework that has not been used for some time, run
off a reasonable amount of water to flush out any debris
that may have collected in the pipes.
25
In the interest of the environment
Electrical connection
Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution.
If you require any further advice please contact your
local water authority.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the top of the
rim of the open door.
Mo
Pro d. .....
d.
No .....
. .....
.....
.
Ser
. No
. .....
....
SHOWER
SINK
TOILET
BATH
Mod. ..........
Prod. No. ...........
BIDET
Ser. No. .........
P0042 BD
WASHING
MACHINE
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363/A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
TREATED
DISCHARGE
RIVER
RIVER
P0987
GREEN & YELLOW
13 A
E
N
L
BROWN
BLUE
P1041
26
CORD CLAMP
The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the
earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal marked «N» or coloured black.
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
WARNING:
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely. Should the appliance power supply
cable need to be replaced, this must be carried
out by our Service Force Centre.
The power supply cable must be easily accessible
after installing the appliance.
Permanent connection
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
27
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use.
More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum
cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150
countries around the world.
© Electrolux plc 2004