Casio 3238 Watch User Manual

MA0508-EC
Operation Guide 3320/3352
About This Manual
• Depending on the model of your watch, display text
appears either as dark figures on a light background
(Module 3320), or light figures on a dark background
(Module 3352). All of the illustrations in this manual
show Module 3320.
• Button operations are indicated using the letters shown
in the illustration.
• All of the displays in this manual show black-on-white.
• For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Module 3320
Module 3352
Warning!
• The longitude, lunitidal interval, Moon phase indicator and tide graph data that
appear on the display of this watch are not intended for navigation purposes.
Always use proper instruments and resources to obtain data for navigation
purposes.
• This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of
tidal movements only.
• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.
General Guide
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Timekeeping Mode
Moon/Tide Data Mode
Press
Countdown Timer Mode
Stopwatch Mode
Alarm Mode
Hand Setting Mode
.
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
• In the Timekeeping Mode, you can press D to change the display format as shown
below.
Tide Graph
Moon phase
indicator
Day of the Week
Month – Day
Day of week
Month – Day
Tide Graph
Press
.
PM indicator
Hour : Minutes Seconds
• The tide graph shows tidal movements throughout the current date. The flashing
location in the tide graph indicates the tide for the current time (the digital time kept
by the Timekeeping Mode).
• The Moon phase indicator shows the current Moon phase in accordance with the
current date as kept in the Timekeeping Mode.
Important!
• Moon phase, tide graph data, and Moon/Tide Data Mode data will not be displayed
properly unless the Timekeeping Mode current date and time settings and Home
Site data are configured correctly. See “Home Site Data” for more information.
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST), the 12/24-hour format, and the illumination duration.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Seconds
DST
Illumination Duration
Hour
Day
Minutes
Month
12/24-Hour Format
3. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen
To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (ON) and
Standard Time (OF)
Change the hour or minutes
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Change the year
Change the month or day
Select three seconds or one second as the
illumination duration
Do this:
Press D.
Press D.
Use D (+) and B (–).
Press D.
Use D (+) and B (–).
Press D.
4. Press A twice to exit the setting screen.
• The first press of A displays the GMT differential setting screen. Pressing A again
exits the setting screen.
• Resetting the seconds only (without changing the DST, hour, or minute setting)
causes the analog minute hand setting to be adjusted automatically.
• See “Digital Time Daylight Saving Time (DST) Setting” below for details about the
DST setting.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• For details about illumination duration, see “Display Illumination”.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the seconds
start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
4. Press A twice to exit the setting screen.
• The DST indicator appears on the Timekeeping, Moon/
Tide Data, Alarm, and Hand Setting Mode screens to
On/Off status
indicate that Daylight Saving Time is turned on. In the
DST indicator
case of the Moon/Tide Data Mode, the DST indicator
appears on the Tide Data screen only.
Year
1
Operation Guide 3320/3352
Home Site Data
Tide graph data will not be displayed properly unless Home Site data (GMT
differential, longitude, and lunitidal interval) is configured correctly.
• The GMT differential is the time difference of the time zone where the site is located
and Greenwich Mean Time.
• The lunitidal interval is the time elapsing between the Moon’s transit over a meridian
and the next high tide at that meridian. See “Lunitidal Interval” for more information.
• This watch displays lunitidal intervals in terms of hours and minutes.
• The “Site/Lunitidal Interval Data List” provides GMT differential, longitude, and
lunitidal interval information around the world.
• The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch, and whenever you have the battery replaced. Change
these settings to match the area where you normally use the watch.
GMT differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,
20 minutes)
To configure Home Site data
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press A again to display the GMT differential setting
screen.
3. Press C to move the flashing in the sequence shown
below to select other settings.
• While the Tide Data screen is displayed, pressing D advances to the next hour.
• While the Moon Data screen is displayed, pressing D advances to the next day.
• You can also specify a date for tide data or Moon data. For details, see “To specify a
date” below.
• Whenever you enter the Moon/Tide Data Mode, the screen (Moon Data or Tide
Data) that was displayed when you last exited the mode appears first. The initial
Tide Data screen shows the data for the 6 a.m. for the current date, while the Moon
Data screen shows the data for the current date.
To specify a date
1. In the Moon/Tide Data Mode, hold down A until the
year setting starts to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Month – Day
Year
Month
Day
3. While a setting is flashing, use D (+) or B (–) to
change it.
• You can specify a date in the range of January 1,
2000 to December 31, 2039.
Year
4. Press A to exit the setting screen.
5. Press A to toggle between the Moon Data screen and Tide Data screen.
GMT differential
GMT
Differential
Longitude
Luntidal Interval
Hours
Luntidal Interval
Minutes
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
4. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
GMT Differential
Screen
Longitude
Lunitidal Interval
Hours, Minutes
Button Operations
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of –11.0 to
+14.0, in 0.5-hour units.
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of 179°W to
180°E, in 1-degree units.
Use D (+) and B (–) to change the setting.
Minutes
Seconds
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
• See “To configure the countdown timer” for information
about setting up the timer.
• When the digital time DST setting is on, the GMT differential can be set in a range
of –10.0 to +15.0 in 0.5-hour units.
5. Press A to exit the setting screen.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by
20 seconds.
• Holding down D advances the analog time setting at
high speed.
• If you need to advance the analog time setting a long way, hold down D until the
time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,
or countdown beeper) starts to sound.
4. Press A to exit the setting screen.
• The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
• To return to the Timekeeping Mode, press C.
Moon/Tide Data
Tide graph
Time
Moon phase indicator
Moon/tide data lets you view the Moon age and Moon
phase for a particular date, and tidal movements for a
particular date and time for the Home Site.
• If you suspect that the Moon/tide data is not correct for
some reason, check the Timekeeping Mode data (current
time, date, and Home Site settings), and make changes
as required.
• See “Moon Phase Indicator” for information about the Moon
phase indicator and “Tide Graph” for information about
the tide graph.
• All of the operations in this section are performed in the
Moon/Tide Data Mode, which you enter by pressing C.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
• Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you can
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
• When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
• When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
• Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
• 30 seconds before the end of the countdown, the watch emits four short beeps.
• The watch emits a short beep for each of the last 10 seconds of the countdown.
• If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Start Time
Progress Beeper
Tide Data Screen
To view current Moon/Tide Mode data
In the Moon/Tide Data Mode, each press of A toggles between the Tide Data screen
and the Moon Data screen.
• The tide graph shows tidal movements throughout the current date. The flashing
location in the tide graph indicates the tide for the currently displayed time. The
Moon data screen shows the Moon age and Moon phase for the current date.
Tide Data Screen
Moon Data Screen
Tide graph
Month – Day
Press
Time
Auto-repeat
3. When the setting you want to change is flashing, use
B and D to change it as described below.
Setting
Start Time
Auto-repeat
Progress Beeper
.
Screen
Button Operations
Use D (+) and B (–) to change the setting.
• You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Press D to toggle auto-repeat on (
displayed) and off
(
displayed).
Press D to toggle the progress beeper on (ON) and off
(OF).
4. Press A to exit the setting screen.
• You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
Moon phase
indicator
Moon age
2
Operation Guide 3320/3352
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
• The countdown timer operation continues even if you
exit the Countdown Timer Mode.
• Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
• To completely stop a countdown operation, first pause it
(by pressing D), and then press A. This returns the
countdown time to its starting value.
Stopwatch
1/100 second
Minutes
Seconds
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes,
59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
Alarm on indicator
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
• Turning on a one-time alarm (AL1through AL4)
displays the alarm on indicator on its Alarm Mode
screen.
• Turning on the snooze alarm (SNZ) displays the alarm
on indicator and snooze alarm indicator on the Alarm
Mode snooze alarm screen, and in all other modes.
Snooze alarm
On/Off
• In all modes (except for the Alarm Mode), the alarm on
indicator
status
indicator is shown for any alarm that is currently turned
on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Hourly time signal
Signal (SIG).
on indicator
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
• The Hourly Time Signal on indicator is shown on the
display on the Alarm Mode Hourly Time Signal screen,
and in all other modes while the Hourly Time Signal is
turned on.
On/Off status
To measure times with the stopwach
Display Illumination
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Split
Split release
Stop
Clear
Split Time
Start
(SPL displayed)
Two Finishes
Start
Auto light switch indicator
Split
Stop
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Clear
Alarms
On/Off status
Alarm number
Alarm time
(Hour : Minutes)
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
AL1through AL4), one is for a snooze alarm
(indicated by SNZ), and one is for the Hourly Time
Signal (indicated by SIG).
• When you enter the Alarm Mode, the data you were
viewing when you last exited the mode appears first.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1through AL4. To set the snooze alarm, display the screen indicated
by SNZ.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
Display illumination uses an EL (electro-luminescent)
panel that causes the entire display to glow for easy
reading in the dark. The watch’s auto light switch
automatically turns on display illumination when you angle
the watch for reading towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” for more important
information.
To illuminate the display
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of the current auto light switch
setting.
• You can use the procedure below to select either one second or three seconds as
the illumination duration. When you press B, the illumination will remain on for
about one second or three seconds, depending on the current illumination duration
setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C eight times so the illumination duration setting
screen is on the display.
3. While the illumination duration setting is flashing, press
D to toggle the setting between one second ( ) and
three seconds ( ).
4. Press A twice to exit the setting screen.
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on for about one second or
three seconds, whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
Parallel to ground
More than 40 °
Warning!
• Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged in
any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not surprise or distract
others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode, hold down B for about two seconds to toggle the auto light switch on
(auto light switch indicator displayed) or off (auto light switch indicator not displayed).
• The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
• In order to protect against running down the battery, the auto light switch
automatically turns off approximately six hours after you turn it on.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
3
Operation Guide 3320/3352
Illumination Precautions
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below.
Module 3320
Module 3352
Moon phase
indicator
(part you cannot see)
Moon
Module
Phase
3320
Indicator Module
3352
Moon Age
0, 1, 29
New
Moon Phase
Moon
2-5
6-9
10 - 13
First
Quarter
(Waxing)
Moon phase (part you can see)
14 - 16
Full
Moon
17 - 20
21 - 24 25 - 28
Last
Quarter
(Waning)
• The Moon phase indicator shows the Moon as viewed at noon from a position in the
Northern Hemisphere looking south. Note that at times the image shown by the
Moon phase indicator may differ from that of the actual Moon in your area.
• The left-right orientation of the Moon phase is reversed when viewing from the
Southern Hemisphere or from a point near the equator.
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle during which it appears to wax and
wane due to how the Sun illuminates the Moon and the relative positioning of the
Earth, Moon, and Sun. The greater the angular distance between the Moon and the
Sun,* the more we see illuminated.
* The angle to the Moon in relation to the direction at which the Sun is visible from the
Earth.
This watch performs a rough calculation of the current Moon age starting from day 0
of the moon age cycle. The actual Moon age average cycle is 29.53 days, but this can
vary anywhere from –1 day to +1 day for specific months. Since this watch performs
calculations using integer values only (no fractions), the margin for error of the
displayed Moon age is ± 2 days.
Tide Graph
The Tide Graph screen shows one of three different waveforms to indicate spring tide,
intermediate tide, or neap tide as the current tide pattern. In addition, the current tide
level is indicated within the displayed tide pattern as a column of flashing dots.
High
Middle
Low
Spring Tide
Intermediate Tide
Neap Tide
• Spring Tide: Tides occurring at new and full Moons, when the range between high
and low tide is greatest.
• Neap Tide: Tides occurring at first and third Moon quarters, when the range between
high tide and low tide is smallest.
• Intermediate Tide: Indicates tide at the midpoint between spring tide and neap tide.
Tidal Movements
Tides are the periodic rise and fall of the water of oceans, seas, bays, and other
bodies of water caused mainly by the gravitational interactions between the Earth,
Moon and Sun. Tides rise and fall about every six hours. The tide graph of this watch
indicates tidal movement based on the Moon’s transit over a meridian and the lunitidal
interval. The lunitidal interval differs according to your current location, so you must
specify a lunitidal interval in order to obtain the correct tide graph readings.
Lunitidal Interval
Theoretically, high tide is at the Moon’s transit over the meridian and low tide is about
six hours later. Actual high tide occurs somewhat later, due to factors such as
viscosity, friction, and underwater topography. Both the time differential between the
Moon’s transit over the meridian until high tide and the time differential between the
Moon’s transit over the meridian until low tide are known as the “lunitidal interval”.
When setting the lunitidal interval for this watch, use the time differential between the
Moon’s transit over the meridian until high tide.
Graphic Area
The following describes the information indicated by the graphic area in each mode.
Graphic area
Mode
Timekeeping
Moon/Tide Data
Countdown Timer
Stopwatch
Alarm
Hand Setting
Graphic Area
Timekeeping Mode seconds
No indication
Countdown time minutes
Stopwatch time seconds
No indication
No indication
• The electro-luminescent panel that provides illumination loses power after very long
use.
• Display illumination may be hard to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Illumination automatically turns off whenever an alarm sounds.
• Frequent use of the light shortens the battery life.
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist.
More than 15 degrees
Doing so causes the auto light switch to operate when it
too high
is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the
auto light switch feature.
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off in about one second or three seconds, even if you keep the
watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back towards you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Site/Lunitidal Interval Data List
Site
Anchorage
Bahamas
Baja, California
Bangkok
Boston
Buenos Aires
Casablanca
Christmas Island
Dakar
Gold Coast
Great Barrier Reef, Cairns
Guam
Hamburg
Hong Kong
Honolulu
Jakarta
Jeddah
Karachi
Kona, Hawaii
Lima
Lisbon
London
Los Angeles
Maldives
Manila
Mauritius
Melbourne
Miami
Noumea
Pago Pago
Palau
Panama City
Papeete
Rio De Janeiro
Seattle
Shanghai
Singapore
Sydney
Tokyo
Vancouver
Wellington
GMT Differential
Standard
DST/
Time
Summer Time
–9.0
–8.0
–5.0
–4.0
–7.0
–6.0
+7.0
+8.0
–5.0
–4.0
–3.0
–2.0
+0.0
+1.0
+14.0
+15.0
+0.0
+1.0
+10.0
+11.0
+10.0
+11.0
+10.0
+11.0
+1.0
+2.0
+8.0
+9.0
–10.0
–9.0
+7.0
+8.0
+3.0
+4.0
+5.0
+6.0
–10.0
–9.0
–5.0
–4.0
+0.0
+1.0
+0.0
+1.0
–8.0
–7.0
+5.0
+6.0
+8.0
+9.0
+4.0
+5.0
+10.0
+11.0
–5.0
–4.0
+11.0
+12.0
–11.0
–10.0
+9.0
+10.0
–5.0
–4.0
–10.0
–9.0
–3.0
–2.0
–8.0
–7.0
+8.0
+9.0
+8.0
+9.0
+10.0
+11.0
+9.0
+10.0
–8.0
–7.0
+12.0
+13.0
Longitude
Lunitidal
Interval
149°W
77°W
110°W
101°E
71°W
58°W
8°W
158°W
17°W
154°E
146°E
145°E
10°E
114°E
158°W
107°E
39°E
67°E
156°W
77°W
9°W
0°E
118°W
74°E
121°E
57°E
145°E
80°W
166°E
171°W
135°E
80°W
150°W
43°W
122°W
121°E
104°E
151°E
140°E
123°W
175°E
5:40
7:30
8:40
4:40
11:20
6:00
1:30
4:00
7:40
8:30
9:40
7:40
4:50
9:10
3:40
0:00
6:30
10:10
4:00
5:20
2:00
1:10
9:20
0:10
10:30
0:50
2:10
7:30
8:30
6:40
7:30
3:00
0:10
3:10
4:20
1:20
10:20
8:40
5:20
5:10
4:50
*Based on data as of 2003.
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s batteries replaced.
4