Casio 3347 Watch User Manual

Operation Guide 3390
MA0406-EA
Modes and Display Screens
Each press of the C button sounds a confirmation tone and cycles through available modes in the sequence shown below.
• The display will automatically revert to the Timekeeping screen if you leave the Alarm or Hand Setting screen displayed without performing
any operation for about two or three minutes.
World Time Mode
Alarm Mode
Timekeeping Mode
Alarm
Hourly Time Signal
• Alarm off
• Hourly Time Signal off
City Code
Changing Display Screen Contents
(Screen Switching)
(Light)
Button
Each press of the
button cycles display contents in the
following sequence: Calendar Screen \ Seconds Screen \
Current Time Screen.
Current Time
in Selected City
Button
Calendar Screen
Month.Day
Button
Button
Day of the Week
2-second interval
(Mode switching)
Hand Setting Mode
Current Time Screen
Seconds Screen
PM indicator
(no indicator for AM)
Days of the Week
SUN: Sunday
WED: Wednesday
SAT: Saturday
MON: Monday
THU: Thursday
Mode Indicator
Seconds
TUE: Tuesday
FRI: Friday
Mode
Indicator
Hour
What is a radio-controlled watch?
Calibration Signal
Your radio-controlled watch is designed to receive a time
calibration signal that contains standard time data, and adjust its
current time setting accordingly.
• The Japanese calibration signal (Call Sign: JJY) is maintained by
the National Institute of Information and Communications
Technology (NICT). It is a long wave signal transmitted 24 hours a
day from the Mt. Otakadoya transmitter (40kHz) located in
Tamura-gun, Fukushima Prefecture, and from the Mt. Hagane
transmitter (60kHz) located on the border between Saga
Prefecture and Fukuoka Prefecture.
• The U.S. calibration signal (Call Sign: WWVB) is transmitted by
the National Institute of Standards and technology from Fort
Collins, Colorado.
Signal is received
using built-in antenna.
Longwave time
calibration
signal
Signal data
Watch decodes
received data
and converts it
to time data.
Decode
Cesium
atomic
clock
Time data
Watch
Internally
Time is adjusted
according to time
data.
Elapsed Time
Minutes
How a Radio-controlled Watch Works
Transmitter
Stopwatch Mode
Reception Range
This watch is designed to receive the standard time calibration signal of Japan (JJY) or of the United States (WWVB). The signal that is
received depends on the current Home Time setting.
• For information about selecting a Home City, see “Configuring Home Time Settings”. For information about city codes, see the “World Time
City Code List”.
Home City
Transmitter
TYO
Either the Mt. Otakadoya signal (40kHz) or the Mt. Hagane signal (60kHz)
LAX, DEN, CHI, NYC
Fort Collins, Colorado signal
1000km
Japan Transmitter
Locations
Note that transmission of the standard wave may be
interrupted occasionally due to maintenance, lightening, etc.
U.S. Transmitter
Location
3000km
500km
Mt. Hagane
(60kHz)
500km
Mt. Otakadoya
(40kHz)
1000km
Fort Collins
After the watch receives the Standard Time signal, it performs
internal calculations to determine the current time. Because of
this, there may be an error of up to one second in the
displayed time.
1000km
• Under optimum conditions, the calibration signal should be
receivable up to 1,000 kilometers from the transmitter. Note
that the wave is relatively weak at distances greater than
500km, so reception may be poor at long distances.
• Under optimum conditions, the calibration signal should be
receivable up to 3,000 kilometers from the transmitter. Note
that the wave is relatively weak at distances greater than
1,000km, so reception may be poor at long distances.
• Geographic contours, nearby buildings, seasonal conditions, the time of day, can even make reception impossible even when you are within
range of the transmitter.
• Best reception is possible late at night.
1
Operation Guide 3390
Location
Receiving the Calibration Signal
❚ Time Required for Reception
❚ Receive Indicator
Reception is difficult and may even be impossible in the locations
described below. Avoid such locations when performing signal
reception.
• You should think of your watch operating like a radio or TV when it
is receiving the calibration signal.
There are two methods you can use to receive the time calibration signal.
• Auto receive (Reception is performed automatically at
midnight, 2:00, 3:00 and 4:00 each morning.)
• Manual receive (You initiate reception using a button operation.)
• If reception is not successful for any of the normal auto receive
operations shown above, auto receive is performed one more
time at 5:00 a.m.
• The watch is set up for auto receive at the factory, so all you need to
do is to place it in a location that allows good reception each night.
A calibration signal receive operation takes anywhere from about
two to six minutes.
• Note that when “AUTO” (Auto Select) is specified as the
transmitter selection mode, signal reception can take up to
12 minutes.
• See “Configuring Auto Receive Settings” for more information.
The receive indicator cycles from
“Unstable” through “Stable” as
shown below while reception is in
progress. How far it cycles depends
on the signal strength. Keep the
watch in a location where reception
is stable while reception is in
progress.
Among or near buildings
Near high-voltage lines
❚ To position the watch for optimum reception
Remove the watch from your wrist and place it somewhere so its
top (12 o’clock side, where the antenna is located) is facing
approximately in the direction of the signal transmitter. Keep the
watch away from metal objects.
Inside a vehicle
(automobile, train, plane, etc.)
Next to a household appliance
or office equipment (TV, speaker,
fax, computer, cell phone, etc.)
❚ To perform manual receive
In the Timekeeping Mode, hold
down the D button for about
two seconds.
• The watch will beep and
reception will start. An indicator
will appear on the display to
indicate reception conditions.
❚ To interrupt reception
Resin band
Receive Indicator
Press the D button.
Unstable
Stable
• Even under optimum reception conditions, it can take about 10
seconds for reception to stabilize.
• Use the receive indicator to check reception status and to
determine the best location for signal reception.
• Note that weather, the time of day, surroundings, and other
factors can all affect reception.
• All other buttons besides D are disabled during signal reception.
When reception is successful
In a location where there is
radio interference
(construction site, airport, etc.)
The watch terminates reception and adjusts the current time. Next
it beeps and then displays the date and time that the adjustment
was performed.
Near mountains
Metal band
If you are experiencing problems with reception, move away
from the types of locations described above to a location with
better reception, and try again.
❚ To view the last reception date and time
In the Timekeeping Mode, press the D button.
• This causes the display to start cycling through the “
”
screen, last reception date screen, and last reception time screen
at two-second intervals.
• To return to the Timekeeping Mode, press the D button again.
• The watch will return to the Timekeeping Mode automatically if
you do not perform any operation for about one or two minutes.
• Orienting the watch so it is sideways to the transmitter makes it
more difficult to receive the signal.
• Do not move the watch while it is receiving the calibration signal.
The watch does not adjust its current time setting, and displays
“ERR” when signal reception is unsuccessful for some reason.
• The watch will return to the Timekeeping Mode automatically if
you do not perform any operation for about one or two minutes.
Configuring Auto Receive Settings
3.
Use the procedure below to turn auto receive of the time
calibration signal on or off. When TYO (Tokyo) is selected as your
Home City, you can also specify the transmitter selection mode,
which controls which Japanese transmitter signal should be used
for time calibration.
• For information about selecting you Home City, see “Configuring
Home Time Settings”.
• The initial factory default settings for auto receive are Home City =
TYO (Tokyo); Auto Receive = On; Transmitter = AUTO
• The following procedure can be performed only when TYO, LAX,
DEN, CHI, or NYC is selected as the Home City.
❚ To configure auto receive settings
1.
Last Reception
Date
Last Reception
Time
Reception Error (ERR Indicator)
In the Timekeeping Mode,
press the D button.
• This will cause the display to
start cycling through the last
reception date and time
screens.
• The watch will return to the
Timekeeping Mode
automatically if you do not
perform any operation for
about one or two minutes.
2.
4.
Press the D button to
cycle through the
available auto receive
settings.
Auto Receive Settings when the Home City is TYO
• AUTO
Auto receive turned on with automatic selection of either the
Mt. Otakadoya signal (40kHz) or the Mt. Hagane signal
(60kHz), whichever is strongest.
• 40
Auto receive turned on for the Mt. Otakadoya signal (40kHz).
When the setting is the
way you want, press the
A button.
• This will exit the setting
screen and return to the last
reception date and time
screens.
• To return to the Timekeeping
Mode, press the D button
again.
• The watch will return to the
Timekeeping Mode
automatically if you do not
perform any operation for
about one or two minutes.
• 60
Auto receive turned on for the Mt. Hagane signal (60kHz).
• OFF
Auto receive turned off.
Auto Receive Settings when the Home City is NYC,
CHI, DEN, or LAX
• ON
Auto receive turned on for the Ft. Collins, Colorado signal.
• OFF
Auto receive turned off.
Hold down the A button
for about two seconds.
• This will cause the currently
auto receive setting to flash
on the display.
2
Operation Guide 3390
Calibration Signal Reception
Precautions
Troubleshooting
The watch cannot receive the time calibration signal.
• Auto reception can be performed while the watch is in the
Timekeeping Mode or World Time Mode only.
• When a time calibration signal is received, the watch corrects its
digital time setting first, and then adjusts the analog time setting
accordingly. In order to ensure that the analog time matches the
digital time, make sure you adjust the analog time to match the
digital time before signal reception is performed.
• Pressing any button while auto reception is in progress will cause
the watch to beep and then exit the receive operation.
• Make sure you are within the range of the calibration signal
transmitter before performing the reception operation. Remember
that geographic contours, nearby buildings, seasonal conditions,
the time of day, can even make reception impossible even when
you are within range of the transmitter.
• Proper reception may be impossible if there is something blocking
the signal. If reception is unsuccessful, try again.
• This watch is designed to adjust its current time setting in
accordance with the calibration signal transmitted in Japan and
the United States only. It operates like a standard (non-radio
controlled) watch outside of the range of the receivable time
calibration signal transmitters.
• When the watch is unable to adjust its time signal using the
calibration signal for some reason, timekeeping accuracy is within
±15 seconds per month.
• Strong electrostatic charge can cause timekeeping error.
• Signal reception is cancelled if an alarm starts to sound while it is
being performed.
• The watch’s calendar shows dates up to the year 2099.
Attempting a receive operation after that causes an error.
The auto receive ON/OFF settings don’t appear when
configuring auto receive settings.
• Check the auto signal reception setting whenever you have
problems with signal reception or when the time setting produced
by signal reception is incorrect.
• The initial factory default configuration of the reception settings
are shown below. You do not need to change these settings if
you use the watch in Japan.
• Auto receive ON/OFF settings do not appear on the display
unless TYO (Japan), NYC (New York), CHI (Chicago), DEN
(Denver), or LAX (Los Angeles) is selected as the Home City.
Use the procedure under “To configure home time settings” to
select your correct Home City.
The auto receive AUTO, 40, and 60 settings do not appear when
configuring auto receive settings.
• The AT, JP40, and JP60 transmitter selection mode options are
available only when TYO (Tokyo) is selected as the Home City
code.
Use the procedure under “To configure home time settings” to
select your correct Home City.
Auto Receive
Auto Japan transmitter select
(40kHz/ 60kHz)
Home City
Tokyo
Summer Time
Auto switching in accordance
with signal data
• Is the signal being transmitted?
Though the Japanese calibration signal (Call Sign: JJY) is
continually transmitted by the National Institute of Information and
Communications Technology (NICT) in theory, it may sometimes
be interrupted for periodic maintenance work, or because of
lightening or other problems.
• Are you within the reception range of a transmitter?
See “Reception Range” for information about areas where the
watch can receive the signal.
• Is there something in the immediate area that may be interfering
with reception?
Even if you are within the reception range of a transmitter, objects
between you and the transmitter or electrical noise can interfere
with reception. Avoid such areas during signal reception. See
“Location” for more information.
• Do you have the correct Home City code selected?
Remember that auto receive is not performed unless TYO
(Japan), NYC (New York), CHI (Chicago), DEN (Denver), or LAX
(Los Angeles) is selected as the Home City. Select the correct
Home City code using the procedure under “To configure home
time settings”.
• Is auto receive turned off (OFF)?
Use the procedure under “Configuring Auto Receive Settings” to
turn on auto receive.
• Is the watch in any mode other than the Timekeeping Mode or
World Time Mode during the auto receive times (midnight, 2:00
a.m., 3:00 a.m., 4:00 a.m., and 5:00 a.m.)?
Auto receive is performed only when the watch is in the
Timekeeping Mode or World Time Mode. It is not performed if the
watch is in any other mode.
Pressing the B button in any mode (except when a flashing
setting screen is displayed) illuminates the face of the watch for
easy reading in the dark.
• You can use the procedure under
“To specify the illumination
duration” to configure the
illumination duration as
approximately 1.5 seconds or
3 seconds.
Important!
• Auto receive is performed in the middle of the night, when
reception conditions are best.
Before going to bed at night, place the watch near a window, with
its 12 o’clock position facing in the general direction of the
transmitter.
• The light may be difficult to see if you turn it on under bright
sunlight.
• If you press a button that sounds a confirmation tone to sound or
if an alarm operation starts while the face is illuminated,
illumination will turn off.
• Illumination is disabled while a manual time calibration signal
receive operation is in progress.
• Hold down the lower right D button for about two seconds.
The watch will beep to indicate that manual receive has started.
Place it near a window, with its 12 o’clock position facing in the
general direction of the transmitter.
How can I view the last reception date and time?
• In the Timekeeping Mode, press the lower right D button.
This will display the date and time that the time calibration signal
was last received successfully. To return to the Timekeeping
Mode, press the D button again.
• After the watch receives the time calibration signal, it performs an
internal decoding process before updating its time setting.
Because of this, the time setting may be slightly off (within one
second).
Time calibration signal reception is successful, but the current
time is one hour fast.
• Do you have summer time (DST) turned on (ON)?
Use the procedure under “To configure home time settings” to turn
off summer time.
Time calibration signal reception is successful, but the current
time setting is wrong.
• Is the correct city code selected for your Home City?
If you are in Japan, you should have TYO selected for your Home
City. For other areas, select the correct Home City code using the
procedure under “To configure home time settings”.
Face Illumination
What time is auto receive performed?
How can I perform manual receive?
Time calibration signal reception is successful, but the hourly
time signal and current time are slightly off.
❚ To specify the illumination duration
1.
In the Timekeeping Mode,
hold down the A button
for about two seconds.
2.
Press the C button three
times to display the
flashing seconds count.
(3 times)
Seconds
3.
Press the B button to
toggle the illumination
duration between about
1.5 seconds ( indicator)
and 3 seconds
(
indicator).
4.
After the setting is the way you want, press the A
button to exit the setting screen.
• The watch will also exit the setting screen automatically if you
do not perform any operation for about two or three minutes.
• This will cause your city code
to flash on the display.
City Code
3
Operation Guide 3390
Using Summer Time (DST)
World Time Mode
World time lets you display the current time in any one of 30 cities
(29 time zones) around the world.
• When you enter the World Time Mode, the screen for the city that
was displayed when you last exited the mode appears first.
• The seconds count in the World Time Mode is linked with the
Timekeeping Mode seconds count.
• The same 12-hour/24-hour format you select for the Timekeeping
Mode time is also applied in the World Time Mode.
Summer time, or Daylight Saving Time (DST) as is it is known in
some countries, calls for setting clocks ahead one hour during the
summer season. Note that the use of summer time depends on
the country and even the local area.
❚ To search for a city code
In the World Time Mode, press the D button.
• This scrolls westward through the available city codes. A short
while after a city code appears, the display will change to show
the current time in that city.
• Holding down the D button scrolls at high speed.
❚ To turn summer time on or off
1.
City Code
Important!
If the World Time Mode time is incorrect, correct the setting of the
current time or change to another Home City in the Timekeeping
Mode.
• For information about configuring timekeeping settings, see “To
configure home time settings”.
2.
(Scrolls westward)
Current Time in Selected City
• Pressing the A button in the World Time Mode displays the city
code of the currently selected city for about two seconds.
• Selecting a time zone that does not have a city code displays the
GMT time differential for that zone.
The stopwatch measures elapsed time in units of 1/100 second up to 59 minutes, 59.99 seconds (60 minutes total). When the maximum
limit is reached, the elapsed time automatically returns to zero and timing continues from there.
In the Stopwatch Mode, press the D button to start and
stop elapsed time measurement.
Hold down the A button
for about two seconds.
• This toggles summer time on
and off.
• The “DST” indicator appears
on the display and
timekeeping is advanced by
one hour when summer time
is turned on.
• You can turn summer time on
or off independently for each
World Time Mode city. Note,
however, that you cannot turn
on summer time for the “GMT”
city code.
DST Indicator
City
GMT
Code Differential
–––
–11
City Name
City
GMT
Code Differential
JRS
+2
City Name
Jerusalem
HNL
–10
Honolulu
JED
+3
Jeddah
ANC
–9
Anchorage
THR
+3.5
Teheran
Dubai
LAX
–8
Los Angeles
DXB
+4
DEN
–7
Denver
KBL
+4.5
Kabul
CHI
–6
Chicago
KHI
+5
Karachi
NYC
–5
New York
DEL
+5.5
Delhi
CCS
–4
Caracas
DAC
+6
Dakar
RIO
–3
Rio de Janeiro
RGN
+6.5
Yangon
–––
–2
BKK
+7
Bangkok
Hong Kong
–––
–1
HKG
+8
GMT
+0
Greenwich Mean Time SEL
+9
Seoul
LON
+0
TYO
+9
Tokyo
Adelaide
London
PAR
+1
Paris
ADL
+9.5
BER
+1
Berlin
SYD
+10
Sydney
ATH
+2
Athens
NOU
+11
Noumea
CAI
+2
Cairo
WLG
+12
Wellington
• The contents of the above table are current as of December 2003.
• Time differentials in the above table are in accordance with
Universal Time Coordinated (UTC).
❚ Elapsed Time Measurement
Stopwatch Mode
❚ To perform elapsed time measurement
In the World Time Mode,
use the D button to
display the screen for the
city code whose summer
time setting you want to
change.
World Time City Code List
❚ Stopwatch Mode Display Screens
• Elapsed Time Screen
The display shows the minutes and seconds.
Start
Stop
Reset
Pressing the A button while timing is stopped resets the stopwatch to all zeros.
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting it to all zeros causes the elapsed time measurement to resume from
where it was last stopped.
❚ Split Time Measurement
Start
Record Split
Clear Split
Stop
Pressing the A button while timing is being performed displays the split time screen, but timing continues internally.
• Changing to another mode while a split time is displayed clears the split time operation.
(Split/Reset)
Reset
❚ 1st and 2nd Place Finishers
Minutes
(Start/Stop)
Seconds
• Paused Elapsed Time Measurement Screen
When elapsed time measurement is paused, the display alternates
between a minute/second screen and a 1/100 second screen at 2second intervals.
2-second
interval
Start
1st Finish
2nd finish
Displays time of 2nd finisher.
Reset
(Displays time of 1st finisher.)
Pressing the D button while the split time screen is on the display stops elapsed time measurement, and leaves the split time screen on
the display. Press the A button to exit the split time screen and display the elapsed time when the measurement was stopped.
Split Time Screen
Split Indicator
Minutes
Seconds
1/100 Second
The split time screen cycles alternately cycle through the split
indicator, a minute/second screen, and a 1/100 second screen.
Minutes
Seconds
1/100 Second
4
Operation Guide 3390
Using the Alarms and Hourly Time Signal
You can set the daily alarms in 1-minute increments. The watch
beeps for 10 seconds when the current time in the Timekeeping
Mode reaches the alarm time you set.
The Hourly Time signal causes the watch to beep every hour on
the hour.
❚ To set the alarm time
1.
When you enter the Alarm Mode, the screen that was displayed
when you last exited the mode appears first.
Alarm Screen
Hourly Time Signal Screen
2.
In the Alarm Mode, press
the D button to display
the alarm screen.
Hold down the A button
for about two seconds.
• This will cause the hour digits
of the displayed alarm time to
flash.
• Displaying the setting screen
automatically turns on the
alarm.
(Back)
Use the D (+) and B (–)
buttons to change the
hour setting.
• Holding down either button
changes the setting at high
speed.
• When setting the hour, make
sure you specify AM (no
indicator) or PM (P) correctly
when using 12-hour
timekeeping, or that you
specify the correct 24-hour
time.
• The same 12-hour/24-hour
format you select for the
Timekeeping Mode home time
is also applied in the Alarm
Mode.
❚ To display the alarm screen
In the Alarm Mode, press the D button to toggle the display
between the alarm screen and the Hourly Time Signal
screen.
3.
Hour
4.
(Forward)
5.
(Back)
Use the D (+) and B (–)
buttons to change the
minute setting.
• Holding down either button
changes the setting at high
speed.
6.
(Forward)
When the setting is the way you want, press the A
button.
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
Press the C button to
select the minute setting.
• This causes the minute digits
to flash.
• Alarm off
Minutes
• Hourly Time Signal off
❚ To turn the alarm on or off
❚ To turn the hourly time signal on or off
1.
In the Alarm Mode, use the D button to display the
alarm screen.
1.
Press the A button to toggle the alarm
on (“
” displayed) or off (“
” displayed).
2.
2.
Alarm Off
Alarm On
In the Alarm Mode, use the D button to display the
Hourly Time Signal screen.
Press the A button to toggle the Hourly Time Signal on
(“
”) or off (“
”).
Hourly Time Signal Off
Hourly Time Signal On
Configuring Home Time Settings
Home time settings include your Home City (the city where you
will normally use the watch), the current time and date in your
Home City, and other settings.
• Use the Timekeeping Mode to configure home time settings.
If you are planning to manually adjust both the digital and
analog settings, be sure to adjust the digital setting first.
❚ To configure home time settings
1.
Alarm Time
❚ To stop the alarm beeper
In the Timekeeping Mode,
hold down the A button
for about two seconds.
• This will cause the city code
currently selected as the
Home City to flash on the
display.
2.
• See the “World Time City
Code List” for information
about city codes.
• Holding down either button
scrolls at high speed.
3.
City Code
Press the D button to
scroll through the city
codes until the one you
want to select is
displayed.
TYO=Tokyo
(Forward)
When the city code you
want is displayed, press
the C button.
• This will display the summer
time (DST) setting screen.
Press any button.
❚ To test the alarm
In the Alarm Mode, hold down the D button to sound the alarm.
5
Operation Guide 3390
4.
Press the D button to
cycle through the
available summer time
(DST) settings until the
one you want to select is
displayed.
5.
Home City
Code
• AUTO
This setting enables the auto summer time setting, which
turns summer time on or off in accordance with the received
time calibration signal.
• This setting uses Japan summer time data when TYO is
selected as the Home City, and U.S. summer time data
when NYC, CHI, DEN, or LAX is selected as the Home
City.
• Note that “AUTO” can be selected only when TYO, LAX,
DEN, CHI, or NYC is selected as the Home City.
6.
When the summer time
setting is the way you
want, use the C button to
cycle the display through
the settings shown below.
Summer Time
Day
Month
12/24-hour
Timekeeping
Seconds
Year
Minute
Hour
• OFF
This setting turns off summer time and returns to normal
timekeeping.
• ON
This setting turns on summer time and advances the current
time by one hour. The DST indicator appears on the display
when this setting is selected.
9.
When all of the settings are the way you want, press the
A button.
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
Digital-Analog Synchronization
After adjustment of the digital time, the watch automatically
adjusts its analog setting to match.
• When adjusting the analog time, the hands move clockwise.
• Depending on how many hours different the digital and analog
time settings are, it may take some time for the analog hand
setting procedure to be finished.
Adjusting the Analog Time Setting
You can use the Hand Setting Mode to manually adjust the analog
time when it does not match the digital time.
1.
In the Hand Setting Mode,
hold down the A button
for about two seconds.
• This will cause the hour and
minute setting of the digital
time to flash on the display.
2.
7.
8.
Indicates 12-hour or
24-hour timekeeping.
While the seconds are
selected, press the D
button to reset them to 00
in accordance with the
time signal on the radio,
TV, etc.
• Pressing the D button while
the seconds count is in the
range of 30 to 59 resets it to
00 and also adds 1 to the
minutes. Pressing the D
button in the range of 00 to 29
resets the seconds count
without changing the minutes.
• Pressing the B button while
the seconds count is flashing
changes the face illumination
duration. See “Face
Ilumination” for more
information.
While the hour, minutes,
year, month, or day setting
is flashing, use the D (+)
button to change the
setting.
• Holding down the D button
changes the setting at high
speed.
Hour
(Forward)
Minutes
Use the C button to select each of the settings and the
D button to change them.
Seconds reset to 00.
• When setting the hour, make sure you specify AM (no indicator) or
PM (P) correctly, or that you specify the correct 24-hour time.
• You can set a year in the range of 2000 to 2099. The day of the
week is set automatically in accordance with the date you set.
• The watch automatically makes adjustments for leap years and
month lengths.
High-speed Lock
• While holding down the D button to start high-speed clockwise
movement of the hands, press the B button to lock the
high-speed hand movement. You can then release the buttons.
• High-speed hand movement will continue until it completes a
12-hour cycle, or until you press any button to stop it.
• High-speed hand movement will also stop momentarily if an alarm
starts to sound. High-speed movement will resume after the alarm
stops.
3.
When the setting is the way you want, press the A
button.
• This exits the setting screen and automatically synchronizes
the minute hand with the current seconds count.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
Use the D (+) button to
adjust the hour and
minute hands so they
match the digital time.
• Each press of the D button
moves the hands 20 seconds
clockwise.
• Holding down the D button
moves the hands at high
speed.
While the 12/24-hour
timekeeping setting is
flashing, press the D
button to toggle between
12-hour (“12H”) and
24-hour (“24H”)
timekeeping.
(Forward)
6