Casio 3368 Watch User Manual

MA0504-EB
Operation Guide 3358/3368/3798
About This Manual
• The operational procedures for Modules 3358, 3368 and 3798 are identical. All of
the illustrations in this manual show Module 3358.
• Button operations are indicated using the letters shown in the illustration.
• All of the displays in this manual show black-on-white.
• For the sake of simplicity, the sample displays in this manual do not show the analog
hands of the watch.
Module 3358
Module 3368
Module 3798
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
General Guide
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Timekeeping Mode
World Time Mode
Press
Countdown Timer Mode
Stopwatch Mode
Alarm Mode
Hand Setting Mode
.
4. When the setting you want to change is flashing, use B and D to change it as
described below.
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
• In the Timekeeping Mode, you can press D to change the display format as shown
below.
Day of the Week
Month – Day
Day of week
Month – Day
Press
.
Hour : Minutes
Hour : Minutes
PM indicator
Seconds
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST), your Home City code (the code for the city where you
normally use the watch), the 12/24-hour format, and the illumination duration.
• This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City. If your location is not included in the
preset city codes, select the preset city code that is in the same time zone as your
location.
• Note that all of the times for the World Time Mode city codes are displayed in
accordance with the digital time and date settings you configure in the Timekeeping
Mode.
• After you correctly set your Home City time and date, you can set the watch up for
timekeeping with a different city code simply by changing the Home City code in the
Timekeeping Mode.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C twice to move the flashing to the Home City
code setting (see the illustration below), and then use
B and D to select the code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table”.
Screen
To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (ON) and
Standard Time (OF)
Change the Home City code
Change the hour or minutes
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Change the year
Change the month or day
Select three seconds or one second as the
illumination duration
Do this:
Press D.
Press D.
Use D (east) and B (west).
Use D (+) and B (–).
Press D.
Use D (+) and B (–).
Press D.
5. Press A to exit the setting screen.
• Resetting the seconds only (without changing the DST, Home City code, hour, or
minute setting) causes the analog minute hand setting to be adjusted to match the
seconds count automatically. If you change any of the other settings, you will have
to adjust the hand setting manually.
• See “Digital Time Daylight Saving Time (DST) Setting” below for details about the
DST setting.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• For details about illumination duration, see “Illumination”.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the seconds start to flash, which
indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON displayed) and Standard
Time (OF displayed).
4. Press A to exit the setting screen.
• The DST indicator appears on the Timekeeping, Alarm, and Hand Setting Mode to
indicate that Daylight Saving Time is turned on.
DST indicator
3. Press C to move the flashing in the sequence shown below to select the other settings.
Seconds
DST
Illumination Duration
Home City Code
Day
Month
Hour
Year
Minutes
Module 3358
Module 3368
Module 3798
12/24-Hour Format
1
Operation Guide 3358/3368/3798
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by
20 seconds.
• Holding down D advances the analog time setting at
high speed.
• If you need to advance the analog time setting a long way, hold down D until the
time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,
or countdown beeper) starts to sound.
4. Press A to exit the setting screen.
• The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
• To return to the Timekeeping Mode, press C.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
• Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
• 30 seconds before the end of the countdown, the watch emits four short beeps.
• The watch emits a short beep for each of the last 10 seconds of the countdown.
• If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Start Time
Auto-repeat
Progress Beeper
3. When the setting you want to change is flashing, use
B and D to change it as described below.
World Time
World Time digitally displays the current time in 27 cities
(29 time zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
City code
Current time for
the selected city code
To view the time in another city
In the World Time Mode, press D to scroll eastwardly
through city codes.
• For full information about city codes, see the “City Code
Table”.
• If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping Mode
time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary
adjustments.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code whose Standard Time/
Daylight Saving Time setting you want to change.
2. Hold down A for about two seconds to toggle between Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator not displayed).
• The DST indicator is on the display whenever you display a city code for which
Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
• Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT is selected as the city code.
DST indicator
Module 3358
Module 3368
Module 3798
Setting
Start Time
Screen
Auto-repeat
Progress Beeper
Button Operation
Use D (+) and B (–) to change the setting.
• You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Press D to toggle auto-repeat on (
displayed) and off
(
displayed).
Press D to toggle the progress beeper on (ON) and off
(OF).
4. Press A to exit the setting screen.
• You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
• The countdown timer operation continues even if you
exit the Countdown Timer Mode.
• Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
• To completely stop a countdown operation, first pause it
(by pressing D), and then press A. This returns the
countdown time to its starting value.
Stopwatch
The stopwatch lets you measure elapsed time, split times, and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero after it reaches its limit, until
you stop it.
• The stopwatch measurement operation continues even if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen on the display clears the split
time and returns to elapsed time measurement.
• All of the operations in this section are performed in the Stopwatch Mode, which you
enter by pressing C.
Minutes
Seconds
Minutes
1/100 second
Split indicator
Seconds
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
• See “To configure the countdown timer” for information
about setting up the timer.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
• Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you can
press A to reset to the countdown time starting value.
Split
indicator
Module 3358
Module 3368
Module 3798
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Split
Split release
Stop
Clear
Clear
Split Time
Start
Two Finishes
Start
(Split indicator
displayed)
Split
Stop
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
• When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
• When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
2
Operation Guide 3358/3368/3798
Alarms
Illumination
You can set five independent Daily Alarms. When an
Alarm time
alarm is turned on, the alarm tone sounds when the alarm
(Hour : Minutes) time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
Alarm number
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
AL1through AL4), one is for a snooze alarm
(indicated by SNZ), and one is for the Hourly Time
Signal (indicated by SIG).
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
This watch has an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark. The watch’s auto light switch automatically turns on
illumination when you angle the watch for reading towards your face.
• The auto light switch must be turned on (indicated by the auto light switch indicator)
for it to operate.
• See “Illumination Precautions” for more important information.
Auto light switch indicator
On/Off status
Module 3358
Module 3368
Module 3798
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1through AL4. To set the snooze alarm, display the screen indicated
by SNZ.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
To illuminate the display
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of the current auto light switch
setting.
• You can use the procedure below to select either one second or three seconds as
the illumination duration. When you press B, the illumination will remain on for
about one second or three seconds, depending on the current illumination duration
setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C nine times so the illumination duration setting
screen is on the display.
3. While the illumination duration setting is flashing, press
D to toggle the setting between one second ( ) and
three seconds ( ).
4. Press A to exit the setting screen.
Alarm Operation
About the Auto Light Switch
The alarm sounds at the preset time for about 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
While the auto light switch is enabled, illumination turns on whenever you position
your wrist as described below in any mode.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on (ON displayed) and off (OF displayed).
• Turning on a one-time alarm (AL1through AL4) causes the alarm on indicator to
appear on its Alarm Mode screen. In all other modes, the alarm on indicator is
displayed when one or more of the alarms is turned on.
• Turning on the snooze alarm (SNZ) displays the alarm on indicator and snooze
alarm indicator on the Alarm Mode snooze alarm screen, and in all other modes.
• The alarm on indicator flashes while the alarm is sounding.
• The snooze alarm indicator flashes during the 5-minute intervals between alarms.
Snooze alarm indicator Alarm on indicator
Snooze alarm indicator
Alarm on indicator
On/Off
status
Module 3358
Module 3368
Moving the watch to a position that is parallel to the ground and then tilting it
towards you at more than 40 degrees causes illumination to turn on.
Parallel to ground
More than 40 °
Warning!
• Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged in
any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not startle or distract others
around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode, hold down B for about two seconds to toggle the auto light switch on
(auto light switch indicator displayed) or off (auto light switch indicator not displayed).
• The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
• In order to protect against running down the battery, the auto light switch
automatically turns off approximately six hours after you turn it on.
Module 3798
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time Signal (SIG).
2. Press A to toggle it on (ON displayed) and off (OF displayed).
• The Hourly Time Signal on indicator is shown on the display on the Alarm Mode
Hourly Time Signal screen, and in all other modes while the Hourly Time Signal is
turned on.
On/Off status
Module 3358
Hourly time signal on indicator
Module 3368
Module 3798
3
Operation Guide 3358/3368/3798
Reference
City Code Table
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Indicators
The following describes the information indicated by the two graphic indicators in each
mode.
Outer graphic
indicator
Inner graphic
indicator
Module 3358
Mode
Timekeeping
World Time
Countdown Timer
Stopwatch
Alarm
Hand Setting
Inner graphic
indicator
Module 3368
Outer Graphic Indicator
Timekeeping Mode seconds
Timekeeping Mode seconds
Countdown time minutes
Stopwatch time seconds
No indication
No indication
Outer graphic
indicator
City
Code
–––
HNL
ANC
Honolulu
Anchorage
GMT
Differential
–11.0
–10.0
–09.0
LAX
Los Angeles
–08.0
DEN
Denver
–07.0
CHI
Chicago
–06.0
NYC
New York
–05.0
City
CCS
Caracas
RIO Rio De Janeiro
–––
–––
GMT
LON
London
Module 3798
Inner Graphic Indicator
Timekeeping Mode minutes
World Time Mode minutes
Countdown time seconds
Stopwatch time 1/10-second
No indication
No indication
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons scrolls at high
speed.
–04.0
–03.0
–02.0
–01.0
+00.0
PAR
Paris
CAI
JRS
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
Cairo
Jerusalem
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
+01.0
+03.0
+03.5
+04.0
+04.5
+05.0
+05.5
+06.0
+06.5
+07.0
HKG
Hong Kong
+08.0
+02.0
Tokyo
TYO
+09.0
ADL
Adelaide
+09.5
Sydney
SYD
+10.0
NOU
Noumea
+11.0
WLG
Wellington
+12.0
*Based on data as of December 2004.
Other major cities in same time zone
Pago Pago
Papeete
Nome
San Francisco, Las Vegas, Vancouver, Seattle/Tacoma,
Dawson City
El Paso, Edmonton
Houston, Dallas/Fort Worth, New Orleans,
Mexico City, Winnipeg
Montreal, Detroit, Miami, Boston, Panama City,
Havana, Lima, Bogota
La Paz, Santiago, Port Of Spain
Sao Paulo, Buenos Aires, Brasilia, Montevideo
Praia
Dublin, Lisbon, Casablanca, Dakar, Abidjan
Milan, Rome, Madrid, Amsterdam, Algiers, Berlin,
Hamburg, Frankfurt, Vienna, Stockholm
Athens, Helsinki, Istanbul, Beirut, Damascus,
Cape Town
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi, Moscow
Shiraz
Abu Dhabi, Muscat
Male
Mumbai, Kolkata
Colombo
Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Beijing, Taipei, Manila,
Perth, Ulaanbaatar
Seoul, Pyongyang
Darwin
Melbourne, Guam, Rabaul
Port Vila
Christchurch, Nadi, Nauru Island
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s batteries replaced.
World Time
• The World Time Mode times are calculated from the current Home City time setting
in the Timekeeping Mode, using the Greenwich Mean Time (GMT) differentials
associated with each city code.
• The GMT differential is a value that indicates the time difference between Greenwich
Mean Time and the time zone where a city is located.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC) data.
Illumination Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• Illumination may be hard to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Illumination automatically turns off whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist.
More than 15 degrees
Doing so causes the auto light switch to operate when it
too high
is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the
auto light switch feature.
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off after the preset illumination
duration (see “To specify the illumination duration”),
even if you keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back towards you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
4