Casio 3400 Watch User Manual

© 2012 CASIO COMPUTER CO., LTD.
MO1207-EA
Operation Guide 3267 3400
About This Manual
• Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
• Button operations are indicated using the letters shown
in the illustration.
• Note that the product illustrations in this manual are
intended for reference only, and so the actual product
may appear somewhat different than depicted by an
illustration.
E-1
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
Contents
General Guide ......................................................................................................... E-6
Timekeeping ............................................................................................................ E-8
Stopwatch .............................................................................................................. E-12
Recall Mode ........................................................................................................... E-21
Countdown Timer .................................................................................................. E-25
Alarms .................................................................................................................... E-29
Dual Time ............................................................................................................... E-36
Illumination ............................................................................................................ E-38
Reference .............................................................................................................. E-42
Specifications ....................................................................................................... E-47
E-2
E-3
Procedure Lookup
To use the countdown timer ................................................................................ E-26
The following is a handy reference list of all the operational procedures contained in
this manual.
To configure countdown start time and auto-repeat settings .......................... E-27
To set the time and date ......................................................................................... E-8
To test the alarm ................................................................................................... E-33
To set an alarm time ............................................................................................. E-31
To toggle between 12-hour and 24-hour timekeeping ....................................... E-10
To select the operation of Alarm1 ...................................................................... E-34
To toggle the Timekeeping Mode between DST and
Standard Time .................................................................................................. E-11
To turn Alarms 2 and 3 on and off ..................................................................... E-35
To measure elapsed time ..................................................................................... E-15
To measure elapsed time with lap times ............................................................ E-15
To measure elapsed time with split times .......................................................... E-17
To time first and second place finishes .............................................................. E-18
To recall stopwatch time records ........................................................................ E-22
To delete a log ....................................................................................................... E-24
To turn the hourly time signal on and off ........................................................... E-35
To set the Dual Time ............................................................................................. E-36
To illuminate the display manually ...................................................................... E-38
To specify the illumination duration ................................................................... E-39
To turn the auto light switch on and off .............................................................. E-41
To turn the button operation tone on and off ..................................................... E-43
E-4
E-5
Recall Mode
General Guide
Countdown Timer Mode
lll
lll
l
l
▲
▲
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the face of the watch.
Stopwatch Mode
Timekeeping Mode
Press C.
▲
Dual Time Mode
Alarm Mode
lll
lll
l
▲
▲
▲
l
E-6
E-7
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Timekeeping
Day of week
Month – Day
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
Minutes
Seconds screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Hours
PM indicator
llll
Day
lll
l ll
Seconds
lll
E-8
Use the Timekeeping Mode to set and view the current
time and date.
Seconds
DST
Month
Hour
Minutes
Year
Screen:
To do this:
Do this:
Reset the seconds to 00
Press D.
Toggle between Daylight Saving
Time (ON) and Standard Time (OF)
Change the hour or minutes
Press D.
Change the year
Use D (+) and B (–).
Use D (+) and B (–).
Change the month or day
4. Press A to exit the setting screen.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
• See “Daylight Saving Time (DST) Setting” below for details about the DST setting.
E-9
Operation Guide 3267 3400
ll
lll
lll
llll
To toggle the Timekeeping Mode between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C once and the DST setting screen appears.
3.
Press D to toggle between Daylight Saving Time (ON
l
ll
displayed) and Standard Time (OF displayed).
lllll
4. Press A to exit the setting screen.
• The DST indicator appears on the Timekeeping and
On/Off status
Alarm Mode screens to indicate that Daylight Saving
DST indicator
Time is turned on.
l
l
lll l
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and 24hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and the A (AM) indicator appears to the left
of the hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
• The A and P indicators are not displayed with the Timekeeping Mode time on the
Countdown Timer Mode and Dual Time Mode screens.
Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
E-10
E-11
Stopwatch
Remaining
free records
1/100
second
Hours
Minutes
Seconds
The stopwatch lets you measure elapsed time, lap times,
split times, and two finishes. Lap times and split times can
be stored in memory.
• The display range of the stopwatch is 99 hours,
59 minutes, 59 seconds.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-6).
Note
• “Lap time” is the time spent to cover a specific segment
of a race, such as one lap around a track. “Split time” is
the time spent from the beginning of a race up to a
certain point.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even if you exit the Stopwatch
Mode.
• For information about how stopwatch times are stored in memory, see “Memory
Management” (page E-19).
Viewing the Stopwatch Displays
The information that appears in the watch’s upper and lower displays depends on
whether you are measuring lap times or split times.
Lap Time Measurement
Upper Display: Lap time
Lower Display: Elapsed time
Split Time Measurement
Upper Display: Lap time
Lower Display: Elapsed time (Split time appears here for eight seconds as it is stored
in memory.)
• See “To measure elapsed time with lap times” (page E-15) and “To measure elapsed
time with split times” (page E-17) for more information about each type of measurement.
E-12
E-13
• You can perform elapsed time measurement starting from either the lap time screen
or the split time screen (page E-15 and E-17). Whenever you enter the Stopwatch
Mode, the screen (lap time or split time) that was displayed when you last exited the
mode will appear first.
• During a stopwatch elapsed time operation, the upper display initially shows
minutes, seconds, and a 1/100-second value. This changes to hours, minutes, and
seconds when the time in the upper display exceeds 60 minutes.
• The lower display initially shows hours, minutes, seconds, and a 1/100-second
value. This changes to hours, minutes, and seconds when the time in the lower
display exceeds 10 hours.
Seconds
Minutes 1/100 second
Minutes
Hours Seconds
▲
More than one hour
Minutes
Hours
Seconds
To measure elapsed time with lap times
1. When the stopwatch display shows all zeros, press
A to display the lap time screen (indicated by LAP/ ).
2. Press D to start an elapsed time measurement.
• At the time, both the upper and lower displays will
show identical times.
3. Press A to record the time of the first lap.
▲
Minutes
1/100 second
Seconds
More than 10 hours
Hours
To measure elapsed time
Note
• You can perform the following steps starting from either the lap time screen or the
split time screen.
1. Press D to start the stopwatch.
2. Press D again to stop the stopwatch.
• You can resume the measurement operation by pressing D.
3. Press A to clear the stopwatch to all zeros.
E-14
E-15
ll
ll
ll
ll
ll
ll
ll
ll
ll
ll
ll
ll
lll
ll
• Split numbers are incremented automatically starting from 1 whenever you press A
in step 3 of the above procedure. The maximum split number is 99. Recording a split
time after that causes the split number count to restart from 00.
To time first and second place finishes
1. When the stopwatch display shows all zeros, press A to display the split time
screen (indicated by SPL/ ).
2. Press D to start a time measurement.
3. Press A when the first finisher crosses the finish line.
• This freezes the time of the first finisher in the lower part of the display for about
eight seconds. After that, the display returns to elapsed time measurement.
4. Press D when the second finisher crosses the finish line.
• The second finisher’s time will appear in the lower display.
• The difference between the first finisher’s and the second finisher’s time will
appear in the upper display.
5. Press A to clear the stopwatch to all zeros.
E-18
ll
ll
Lap number
E-16
ll
lll
ll
ll
lll
ll
ll
ll
ll
lll
ll
ll
ll
ll
Lap time
ll
Elapsed time
To measure elapsed time with split times
Lap time
1. When the stopwatch display shows all zeros, press A
ll lll
to display the split time screen (indicated by SPL/ ).
2. Press D to start an elapsed time measurement.
• At the time, both the upper and lower displays will
show identical times.
lll
lll
3. Press A to record the time of the first split.
• The current split time appears in the lower display for
Elapsed time
about eight seconds, as the total elapsed time, next
lap time, and next split time continue to be timed
Split Time Recording
(Displayed for eight seconds
internally by the watch. The split number of the
after A is pressed.)
displayed time appears in the upper display.
Split number
• After eight seconds, the ongoing lap time
measurement appears in the upper display and the
ongoing elapsed time measurement appears in the
lower display.
lll
lll
4. Repeat step 3 to record more split times.
5. Press D to stop the stopwatch.
6. Press A to clear the stopwatch to all zeros.
Split time
ll
ll
ll
lll
lll
• This freezes the current lap time in the upper part of
the display for about eight seconds, while
measurement of total elapsed time and the next lap
time continue internally. The lap number of the
displayed time appears in the lower display.
• After eight seconds, the ongoing elapsed time
measurement re-appears in the lower display.
4. Repeat step 3 to record more lap times.
5. Press D to stop the stopwatch.
6. Press A to clear the stopwatch to all zeros.
• Lap numbers are incremented automatically starting
from 1 whenever you press A in step 3 of the above
procedure. The maximum lap number is 99. Recording
a lap after that causes the lap number count to restart
from 00.
ll
lll
ll
ll
ll
ll
Lap time
E-17
Memory Management
A new log is created each time you press D in the Stopwatch Mode to start a new
elapsed time measurement operation. A log contains a log title screen, and records of
all the lap or split times you record during the current elapsed time measurement
operation.
• The capacity of the watch’s memory is 60 records.
• If you are adding records to the only log in memory and watch memory becomes
full, adding another record causes the oldest record in the log to be deleted
automatically to make room for the new record.
• If you are adding records to a log when there are multiple logs in memory and watch
memory becomes full, adding another record causes the oldest log in memory and
all of its records to be deleted automatically to make room for new records.
E-19
Operation Guide 3267 3400
How stopwatch data is stored
The following table shows how stopwatch data is stored when you perform stopwatch
button operations.
Stopwatch Button
Operation
Data Storage Description
From all-zeros,
press D to start.
Creates a new log. Stores the date the button was pressed,
and the new log number.
Press A to
display lap/split
time.
Creates a new record with each button operation. Stores the
lap and split times and total elapsed time at each point the
button is pressed.
Resets the elapsed time to all zeros without recording data.
Press D to stop
elapsed time
measurrement and
then press A to reset.
Recall Mode
Day of week
Month – Day
Log number
Log Title Screen
Use the Recall Mode to recall and delete logs and records
you stored in the Stopwatch Mode. You can use the Recall
Mode to view both lap and split time records.
• When you enter the Recall Mode, the newest log
recorded in the Stopwatch Mode will appear first. If there
are no logs in memory, xxxx appears on the display.
• You can use the Recall Mode to check memory data
even while a stopwatch elapsed time measurement
operation is in progress. However, the time data that is
currently being measured will not appear in the Recall
Mode.
• You can convert a lap time saved in the Stopwatch
Mode to a split time (page E-22).
• See “Recall Mode” (page E-21) for details on how to recall time records from
memory.
E-20
First record
Lap time
Last record
Lap number
Log Title Screen
▲
▲
Press D.
Log number
▲
▲
To recall stopwatch time records
1. In the Stopwatch Mode, check to make sure that the displays reset to all zeros
(page E-15).
• If all zeros are not displayed, reset the stopwatch.
2. Use the A button to select either the lap time screen (to view lap time records) or
the split time screen (to view split time records) (page E-15 and E-17).
• To convert a lap time saved in the Stopwatch Mode to a split time, select the split
time screen.
3. Press the C button to enter the Recall Mode.
4. Use the A button to scroll through the log title screens from the newest to the
oldest until the title screen of the log whose records you want to view is displayed.
5. Press D to scroll through the records contained in the log you selected in step 4,
from the oldest to the newest.
E-21
▲
Split time
Split number
• Whether you will be able to view lap time records or split time records will depend on
the screen you selected in step 2, above.
E-22
Countdown Timer
Timekeeping
Auto-repeat Mode time
on indicator
lll
l
lll
l
To delete a log
1. In the Recall Mode, display the title screen of the log you want to delete.
2. Hold down B and D until CLR stops flashing on the display.
• This deletes the log and all the records inside it.
• Deleting a single log slides all newer logs (ones with higher log numbers) upwards to
fill the empty space. This cause the log numbers of all the newer logs to be reduced
by 1. If there are six logs currently in memory (numbered 01 through 06) and you
delete log 03, the numbers of logs that previously were numbered 04, 05, and 06 will
change to 03, 04, and 05.
E-23
You can set the countdown timer within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
• You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Hours
Seconds
Minutes
E-24
lll
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Auto-repeat on indicator
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
l
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-26) to display it.
lll
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
lll
llll
l
llll
lll
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is reset automatically to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds when the countdown reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
E-25
On/Off status
E-26
3. Perform the following operations, depending on which setting currently is selected
on the display.
• While the start time setting is flashing, use D (+) and B (–) to change it.
• Set 0:00 to specify 24 hours.
• While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press
D to toggle auto-repeat on (0N) and off (0F).
4. Press A to exit the setting screen.
• The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
Start Time
(Hours)
Start Time
(Minutes)
Auto-Repeat
On/Off
E-27
Alarms
Alarm date
(Month – Day)
Alarm number
You can set up to three independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other two are
one-time alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are three alarm screens numbered 1 through 3.
The hourly time signal screen is indicated by :00.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page E-7).
Alarm time
(Hour : Minutes)
E-28
E-29
Operation Guide 3267 3400
To set an alarm time
Alarm Types
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
x1
x2
x3
:00
• You can configure Alarm1 as a snooze alarm or a one-time alarm. Alarms 2 and
3 can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour
Minutes
Month
Day
E-30
E-31
4. While a setting is flashing, use D (+) and B (–) to change it.
• To set an alarm that does not include a month (daily alarm, monthly alarm), set x
for the month. Use D and B until the x mark appears (between 12 and 1) while
month setting is flashing.
• To set an alarm that does not include a day (daily alarm, 1-month alarm), set xx
for the day. Use D and B until the xx mark appears (between the end of the
month and 1) while the day setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Note
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-8)
Displaying the Alarm1 setting screen (page E-31)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes, until
you turn the alarm off or change it to a one-time alarm (page E-34).
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
E-32
E-33
To select the operation of Alarm1
1. In the Alarm Mode, use D to select Alarm1.
2. Press A to cycle through the available settings in the sequence shown below.
Snooze indicator
One-time alarm on
Snooze alarm on
Alarm off
• The applicable alarm on indicator is displayed in all modes when an alarm is turned
on.
• The snooze indicator flashes while the snooze alarm is sounding and during the 5minute intervals between alarms.
• Displaying the Alarm1 setting screen (page E-31) while the snooze alarm is turned
on turns off the snooze alarm automatically (making Alarm1 a one-time alarm).
To turn Alarms 2 and 3 on and off
1. In the Alarm Mode, use D to select a one-time alarm
Alarm on indicator
(alarm number 2 or 3).
2. Press A to toggle the displayed alarm on and off.
• Turning on a one-time alarm (2 or 3) displays the alarm
on indicator on its screen.
• The alarm on indicator is displayed in all modes.
• If any alarm is on, the alarm on indicator is shown on
the display in all modes.
To turn the hourly time signal on and off
Hourly time signal on
1. In the Alarm Mode, use D to select the Hourly Time
indicator
Signal.
2. Press A to toggle the displayed item on and off.
• Turning on the Hourly Time Signal displays the hourly
time signal on indicator on its screen.
• The hourly time signal on indicator is displayed in all
modes.
E-34
E-35
4. When the setting you want to change is flashing, use B and D to change it as
described below.
Dual Time
Timekeeping Mode time
lll
lll
l
l
Dual time
(Hour : Minutes Seconds)
The Dual Time Mode lets you keep track of time in a
different time zone. You can select Standard Time or
Daylight Saving Time for the Dual Time.
• The seconds count of the Dual Time is synchronized
with the seconds count of the Timekeeping Mode.
To set the Dual Time
1. Press C to enter the Dual Time Mode (page E-7).
2. In the Dual Time Mode, hold down A until the DST
setting starts to flash, which indicates the setting
screen.
3. Press C to move the flashing in the sequence shown
below to select the other setttings.
DST
Hour
Screen:
To do this:
5. Press A to exit the setting screen.
• The DST indicator on the Dual Time Mode screen indicates that DST is turned on for
the Dual Time Mode time.
Minutes
E-36
E-37
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, illumination will remain on for about 1.5
seconds or 3 seconds, depending on the current
illumination duration setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. While the seconds are flashing, press B to toggle the
setting between 1.5 seconds ( ) and 3 seconds ( ).
l
l l
3. Press A to exit the setting screen.
lll
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Illumination Precautions” (page E-45) for other
important information about using illumination.
lll
Auto light switch on
indicator
llll
Illumination
E-38
Do this:
Toggle between Daylight Saving Time (ON) Press D.
and Standard Time (OF)
Change the hour or minutes
Use D (+) and B (–).
E-39
Operation Guide 3267 3400
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
More than
40°
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down B for about three seconds to toggle the auto
light switch on (auto light switch on indicator displayed) and off (auto light switch on
indicator not displayed).
• The auto light switch on indicator remains in all modes while the auto light switch is
turned on.
• In order to protect against running down the battery, the auto light switch will turn off
automatically approximately six hours after you turn it on. Repeat the above
procedure to turn the auto light switch back on if you want.
E-40
Reference
E-41
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• The multi-function alarms and Countdown Timer Mode
alarm will sound even if the button operation tone is
turned off.
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Return Feature
• If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch saves any settings you have made up to
that point and exits the setting screen automatically.
• The watch will change to the Timekeeping Mode automatically if you do not perform
any operation in the Recall Mode or Alarm Mode for two or three minutes.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the display), hold down C to toggle
the button operation tone on (mute indicator not displayed) and off (mute indicator
displayed).
• Holding down C to turn the button operation tone on or off also causes the watch’s
current mode to change.
• The mute indicator is displayed in all modes when the button operation tone is
turned off.
E-42
E-43
Scrolling
Illumination Precautions
Timekeeping
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the auto light switch feature.
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s batteries replaced.
• Illumination may be difficult to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
More than 15 degrees
too high
E-44
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
E-46
Alarms: 3 Multi-function*alarms (Two one-time alarms; one snooze/one-time alarm);
Hourly Time Signal
*Alarm type: Daily alarm, Date alarm, 1-month alarm, Monthly alarm
Dual Time: Hour, minutes, seconds, a.m. (A)/p.m. (P)
Other: Daylight Saving Time (summer time)/Standard Time
Illumination: LED (light-emitting diode), Auto Light Switch; Selectable illumination
duration (approximately 1.5 seconds or 3 seconds)
Other: Button operation tone on/off
Battery:
Module 3267: One lithium battery (Type: CR2016)
Approximately 5 years on type CR2016 (10 seconds of alarm
operation per day, one illumination operation (1.5 seconds) per
day)
Module 3400: One lithium battery (Type: CR2025)
Approximately 7 years on type CR2025 (10 seconds of alarm
operation per day, one illumination operation (1.5 seconds) per
day)
• The module number of your watch is stamped on its back cover.
E-48
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off in about 1.5 seconds or 3 seconds,
even if you keep the watch pointed towards your face.
E-45
Specifications
Accuracy at normal temperature: ± 15 seconds a month
Timekeeping: Hour, minutes, seconds, a.m. (A)/ p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Daylight Saving Time (summer time)/Standard Time
Stopwatch:
Measurement Capacity: 99 hours, 59 minutes, 59 seconds
Measurement Unit: 1/100 second (from 0 to 59 minutes, 59.99 seconds) or
1 second (from 1 hour to 99 hours, 59 minutes, 59 seconds)
Measurement Types: Elapsed time, lap times, split times, two finishes
Memory Capacity: 60 records (used for lap times and split times)
Other: Lap/split numbers
Countdown Timer:
Measuring unit: one second
Input range: one minute to 24 hours (1-minute increments and 1-hour
increments)
Other: Auto-repeat timing
E-47