Casio 3768 Watch User Manual

MA0508-EC
Operation Guide 3768/3769
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully and keep it on hand for later reference
when necessary.
Important!
The fishing/hunting level indicator and moon phase indicator produced by this watch
are all based on calculations that use the watch’s current time, date, and Home Site
settings. Because of this, you should make sure that the current date and time, and
your Home Site data are all correct before using the indicators.
• When fishing or hunting, always take proper precautions to ensure your own
personal safety and the personal safety of others around you.
• Note that the fishing/hunting level indicator and moon phase indicator are all based
on calculated values. They are provided only for reference purposes.
• See the “Timekeeping” section of this manual for information about setting the
current time and date, and about specifying your Home Site.
About This Manual
Module 3768
• The operational procedures for Modules 3768 and 3769
are identical. All of the illustrations in this manual show
Module 3768.
• Button operations are indicated using the letters shown
in the illustration.
• For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Module 3769
General Guide
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the face of the watch.
Timekeeping
Mode
Fishing/Hunting
Mode
Press
Stopwatch
Mode
Day of week
Month – Day
Hour : Minutes Seconds
This watch features separate digital and analog
timekeeping. The procedures for setting the digital time
and analog time are different.
• The Moon phase indicator shows the current Moon
phase in accordance with the current date as kept in the
Timekeeping Mode.
• The fishing/hunting level indicator indicates the times
when fish or game can be expected to be feeding. For
more information, see “Fishing/Hunting Mode”.
Important!
• Be sure to configure the current time and date, and your
Home Site data (data for the site where you use the
watch) correctly before using the functions of this watch.
See “Home Site Data” for more information.
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST).
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Seconds
DST
Day
Hour
Month
Minutes
Year
3. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen
Alarm
Mode
Dual Time
Mode
Hand Setting
Mode
.
Timekeeping
Fishing/hunting level
indicator
PM indicator
Countdown Timer
Mode
To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (ON) and
Standard Time (OF)
Change the hour or minutes
Change the year
Change the month or day
Do this:
Press D.
Press D.
Use D (+) and B (–).
4. Press A twice to exit the setting screen.
• The first press of A displays the UTC differential setting screen. Pressing A again
exits the setting screen.
• Resetting the seconds only (without changing the DST, hour, or minute setting)
causes the analog minute hand setting to be adjusted automatically.
• See “Digital Time Daylight Saving Time (DST) Setting” below for details about the
DST setting.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the seconds
DST indicator
start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
4. Press A twice to exit the setting screen.
• The DST indicator appears on the Timekeeping, Fishing/
Hunting, Alarm, and Hand Setting Mode screens to
indicate that Daylight Saving Time is turned on. In the
On/Off status
case of the Fishing/Hunting Mode, the DST indicator
appears on the fishing/hunting level screen only.
Home Site Data
Moon phase, the fishing/hunting level indicator, and Fishing/Hunting Mode data will
not be displayed properly unless Home Site data (UTC differential and longitude) is
configured correctly.
• The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
• The letters “UTC” is the abbreviation for “Coordinated Universal Time”, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap seconds
are added or subtracted as necessary to keep UTC in sync with the Earth’s rotation.
• The “Site Data List” at the back of this manual provides UTC differential, latitude,
and longitude information around the world.
• The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch, and whenever you have the battery replaced. Change
these settings to match the area where you normally use the watch.
UTC differential (+9.0); Longitude (East 140 degrees)
1
Operation Guide 3768/3769
To configure Home Site data
1. In the Timekeeping Mode, hold down A until the
UTC differential
seconds start to flash, which indicates the setting
screen.
2. Press A again to display the UTC differential setting
screen.
3. Press C to move the flashing in the sequence shown
below to select other settings.
UTC
Differential
Longitude
Value
To view the current fishing/hunting level and Moon data
In the Fishing/Hunting Mode, press A to toggle between the fishing/hunting level
screen and the Moon Data screen.
• The fishing/hunting level indicator shows the level for the displayed time. The initial
fishing/hunting level screen shows the level for 6:00 a.m. The Moon data screen
shows the Moon age and Moon phase for the current date.
Fishing/Hunting
Level Screen
East Longitude/
West Longitude
Moon Data Screen
Moon phase indicator
Moon age
Time
Press
.
4. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
UTC Differential
Screen
Longitude Value
East Longitude/
West Longitude
Button Operations
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of –12.0 to +14.0,
in 0.5-hour units.
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of 0° to 180°, in
1-degree units.
Use D to switch between east longitude (E) and west
longitude ( ).
• When the digital time DST setting is on, the UTC differential can be set in a range
of –11.0 to +15.0 in 0.5-hour units.
5. Press A to exit the setting screen.
Fishing/hunting level indicator
To specify a date
1. In the Fishing/Hunting Mode, hold down A until the
year setting starts to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Year
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and
24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and the A (AM) indicator appears to the left
of the hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
• The A and P indicators are not displayed with the Timekeeping Mode time on the
Countdown Timer Mode and Dual Time Mode screens.
Year Month – Day
• While the fishing/hunting level screen is displayed, press D to advance to the next
hour.
• While the Moon Data screen is displayed, press D to advance to the next day.
• You can also specify a particular date (year, month, day) to view its fishing/hunting
level and Moon data. See “To specify a date” for more information.
• When you enter the Fishing/Hunting Mode, the screen (fishing/hunting level or Moon
data) that was displayed the last time you exited the mode appears first.
Year
Month
Day
Month – Day
3. While a setting is flashing, use D (+) or B (–) to change it.
• You can specify a date in the range of January 1, 2000 to December 31, 2099.
4. Press A to exit the setting screen.
5. Use A to display either the fishing/hunting level screen or the Moon Data screen.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
Stopwatch
To adjust the analog time
Hours
Minutes
Seconds
1. In the Timekeeping Mode, press C six times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by
20 seconds.
• Holding down D advances the analog time setting at
high speed.
1/100 second
• If you need to advance the analog time setting a long way, hold down D until the
time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (multi-function alarm, Hourly Time
Signal, or countdown beeper) starts to sound.
4. Press A to exit the setting screen.
• The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
• To return to the Timekeeping Mode, press C.
Moon phase indicator
Time
Year Month – Day
Fishing/hunting level
indicator
Fishing/Hunting
Level Screen
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Split
Split release
Stop
Clear
Clear
Split Time
Start
Fishing/Hunting Mode
(SPL displayed)
The Fishing/Hunting Mode displays an indicator that
shows, as one of five levels, the suitability of a specific
date and time (minute 00 to minute 59 of a particular
hour) for fishing or hunting. This mode also can be used
to display Moon Data (Moon age and Moon phase) for a
specific date.
• If you doubt that the fishing/hunting level indicator or
current Moon data is wrong for some reason, check the
current Timekeeping Mode settings (time, date, and
Home Site), and correct them if required.
• See “Moon Phase Indicator” for information about the
Moon phase indicator.
• All of the operations in this section are performed in the
Fishing/Hunting Mode, which you enter by pressing C.
Two Finishes
Start
Split
Stop
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Countdown Timer
Hours
Minutes
Seconds
Fishing/Hunting Level Indicator
The fishing/hunting level indicator shows the relative favorability of a fishing/hunting
time (calculated in accordance with Moon transit and phase) as shown in the table
below.
Level 5
Level 4
Level 3
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
Level 2
Level 1
Moon Transit
Moon Phase
New moon*
Full moon
First quarter
Last quarter
Upper
Lower
West
East
Other
Level 5
Level 4
Level 3
Level 4
Level 3
Level 2
Other
Level 3
Level 2
Level 1
* These indicators
actually appear
during Moon ages
13.0 to 16.6 (Full
Moon and phase
immediately
preceding it) and
27.7 to 1.8 (New
Moon and phase
immediately
preceding it).
• With Module 3769, the level indicator is .
• The fishing/hunting level indicator changes in accordance with the Moon data.
• In the Timekeeping Mode, the FISH/HUNT indicator flashes whenever the fishing/
hunting level of the current time is 4 or 5.
You can set the countdown timer within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations is this section are performed in the
Countdown Timer Mode, which you can enter using C.
Timekeeping Mode time
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds to signal when the countdown
reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
2
Operation Guide 3768/3769
To set up the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Hours
Auto-repeat
Minutes
3. While a setting is flashing, use D and B to change it as described below.
Screen
To do this:
Do this:
Change the hours or minutes
Use D (+) and B (–).
Toggle auto-repeat on (ON) and off (OF)
Press D.
• To specify a countdown start time of 24 hours, set 0:00.
4. Press A to exit the setting screen.
• The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode screen
while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
Alarms
Alarm number
Alarm time
(Hour : Minutes)
Alarm date (Month – Day)
To turn Alarms 2 and 3, and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select a one-time alarm
(alarm number 2 or 3) or the Hourly Time Signal (:00).
2. Press A to toggle it on and off.
• Turning on a one-time alarm (2 or 3) displays the alarm
on indicator on its screen.
• Turning on the Hourly Time Signal displays the hourly
time signal on indicator.
Alarm on indicator
• The alarm on (ALM) indicator and Hourly time Signal on
(SIG) indicator are displayed in all modes.
You can set up to three independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other two are
one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are three alarms numbered1 through 3. You can
configure Alarm1 as a snooze alarm or a one-time
alarm. Alarms 2 and 3 can be used as one-time alarms
only.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Hourly time signal on
indicator
To select the operation of Alarm1
1. In the Alarm Mode, use D to select Alarm1.
2. Press A to cycle through the available settings in the sequence shown below.
Alarm on
Snooze
alarm on
Alarm off
• The applicable alarm on indicator (SNZ ALM) is displayed in all modes when an
alarm is turned on.
• SNZ indicator flashes during the 5-minute intervals between alarms.
• Displaying the Alarm1 setting screen while the snooze alarm is turned on
automatically turns off the snooze alarm (making Alarm1 a one-time alarm).
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone. You can
select Standard Time or Daylight Saving Time for the Dual Time Mode time.
• In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the current digital time.
To set the Dual Time
DST indicator
Dual time
(Hour : Minutes)
Alarm Types
1. Press C to enter the Dual Time Mode.
2. In the Dual Time Mode, hold down A until the DST
setting starts to flash, which indicates the setting
screen.
3. Press C to move the flashing in the sequence shown
below to select the other setttings.
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a one-time alarm, display one of the screens
indicated by alarm number 2 or 3. To set the snooze
alarm, display the screen indicated by1.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing in the sequence shown below to select other
settings.
Hour
Minutes
Month
DST
Hour
Minutes
Timekeeping Mode time
4. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen
To do this:
Toggle between Daylight Saving Time (ON) and
Standard Time (OF)
Change the hour or minutes
Do this:
Press D.
Use D (+) and B (–).
5. Press A to exit the setting screen.
• The DST indicator on the Dual Time Mode screen indicates that DST is turned on for
the Dual Time Mode time.
Illumination
Two LEDs (light-emitting diodes) and a light guide panel
illuminate the face of the watch for easy reading in the
dark.
• See “Illumination Precautions” for more important
information.
To illuminate the face of the watch
In any mode (except when a setting screen is on the
display), press B to illuminate the face of the watch.
• You can use the procedure below to select either
1.5 seconds or 3 seconds as the illumination duration.
When you press B, the illumination will remain on for
about 1.5 seconds or 3 seconds, depending on the
current illumination duration setting.
Day
4. While a setting is flashing, use D (+) and B (–) to change it.
• To set an alarm that does not include a month (daily alarm, monthly alarm),
set x for the month. Use D and B until the x mark appears (between 12 and 1)
while month setting is flashing.
• To set an alarm that does not include a day (daily alarm, 1-month alarm),
set xx for the day. Use D and B until the xx mark appears (between the end
of the month and 1) while the day setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. While the seconds are flashing, press B to toggle the
illumination duration between 1.5 seconds (x) and 3
seconds ( ).
3. Press A twice to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off or change it to a onetime alarm.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the alarm1 setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
3
Operation Guide 3768/3769
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below.
(part you cannot see)
Moon phase (part you can see)
Moon Phase
Indicator
0.0 - 1.8
27.7 - 29.5 1.9 - 5.5 5.6 - 9.2 9.3 - 12.9 13.0-16.6 16.7- 20.2
Full
First
Moon Phase New
Moon
Moon
Quarter
(Waxing)
Moon Age
20.3-23.9 24.0-27.6
Last
Quarter
(Waning)
• The Moon phase indicator shows the Moon as viewed at noon from a position in the
Northern Hemisphere looking south. Note that at times the image shown by the
Moon phase indicator may differ from that of the actual Moon in your area.
• The left-right orientation of the Moon phase is reversed when viewing from the
Southern Hemisphere or from a point near the equator.
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle. During each cycle, the Moon
appears to wax and wane as the relative positioning of the Earth, Moon, and Sun
changes. The greater the angular distance between the Moon and the Sun,* the more
we see illuminated.
* The angle to the Moon in relation to the direction at which the Sun is visible from the
Earth.
This watch performs a rough calculation of the current Moon age starting from day 0
of the moon age cycle. Since this watch performs calculations using integer values
only (no fractions), the margin for error of the displayed Moon age is ±1 day.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• The multi-function alarms and Countdown Timer Mode
alarm will sound even if the button operation tone is
turned off.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down C to toggle the button operation tone
on ( not displayed) and off ( displayed).
• Holding down C to turn the button operation tone on or
off also causes the watch’s current mode to change.
• The indicator is displayed in all modes when the
bxDton operation tone is turned off.
Auto Return Features
• If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
• If you leave the watch in the Fishing/Hunting Mode, Alarm Mode, and Hand setting
Mode for two or three minutes without performing any operation, it automatically
changes to the Timekeeping Mode.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
Illumination Precautions
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination automatically turns off whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Site Data List
Site
ABIDJAN
ABU DHABI
ADDIS ABABA
ADEN
AMSTERDAM
ANCHORAGE
ATHENS
AZORES
BANGKOK
BEIJING
BEIRUT
BOGOTA
BOSTON
BRASILIA
BUENOS AIRES
CAPE TOWN
CARACAS
CASABLANCA
CHICAGO
CHRISTCHURCH
DAKAR
UTC Differential
DST/
Standard Time Summer Time
+0.0
+1.0
+4.0
+5.0
+3.0
+4.0
+3.0
+4.0
+1.0
+2.0
–9.0
–8.0
+2.0
+3.0
+
–1.0
0.0
+7.0
+8.0
+8.0
+9.0
+2.0
+3.0
–5.0
–4.0
–5.0
–4.0
–3.0
–2.0
–3.0
–2.0
+2.0
+3.0
–4.0
–3.0
+0.0
+1.0
–6.0
–5.0
+12.0
+13.0
+0.0
+1.0
Longitude
Latitude
4°W
54°E
39°E
45°E
5°E
149°W
24°E
25°W
101°E
116°E
36°E
74°W
71°W
48°W
58°W
18°E
67°W
8°W
88°W
173°E
17°W
5°N
24°N
9°N
13°N
52°N
61°N
38°N
38°N
14°N
40°N
34°N
5°N
42°N
16°S
35°S
34°S
11°N
34°N
42°N
44°S
15°N
Site
UTC Differential
DST/
Standard Time Summer Time
DALLAS
–6.0
FORT WORTH
+2.0
DAMASCUS
DENVER
–7.0
DETROIT
–5.0
+6.0
DHAKA
+4.0
DUBAI
+0.0
DUBLIN
EDMONTON
–7.0
EL PASO
–7.0
+1.0
FRANKFURT
+10.0
GOLD COAST
+10.0
GUAM
+1.0
HAMBURG
+7.0
HANOI
+2.0
HELSINKI
+8.0
HONG KONG
HONOLULU
–10.0
HOUSTON
–6.0
+2.0
ISTANBUL
+7.0
JAKARTA
+3.0
JEDDAH
+5.0
KARACHI
+8.0
KUALA LUMPUR
+3.0
KUWAIT
LA PAZ
–4.0
LAS VEGAS
–8.0
LIMA
–5.0
+0.0
LISBON
+0.0
LONDON
LOS ANGELES
–8.0
+1.0
MADRID
+8.0
MANILA
+10.0
MELBOURNE
MEXICO CITY
–6.0
MIAMI
–5.0
+1.0
MILAN
MONTEVIDEO
–3.0
MONTREAL
–5.0
+4.0
MUSCAT
+12.0
NADI
+3.0
NAIROBI
+12.0
NAURU ISLAND
NEW ORLEANS
–6.0
NEW YORK
–5.0
NOME
–9.0
+11.0
NOUMEA
PAGO PAGO
–11.0
PANAMA CITY
–5.0
PAPEETE
–10.0
+1.0
PARIS
+8.0
PERTH
+7.0
PHNOM PENH
PORT OF SPAIN
–4.0
+11.0
PORT VILA
PRAIA
–1.0
+9.0
PYONGYANG
+3.0
RIYADH
+1.0
ROME
SAN FRANCISCO
–8.0
SANTIAGO
–4.0
SAO PAULO
–3.0
SEATTLE
–8.0
+9.0
SEOUL
+8.0
SHANGHAI
+8.0
SINGAPORE
+1.0
STOCKHOLM
+10.0
SYDNEY
+8.0
TAIPEI
+9.0
TOKYO
+8.0
ULAANBAATAR
VANCOUVER
–8.0
+1.0
VIENNA
+7.0
VIENTIANE
+12.0
WELLINGTON
WINNIPEG
–6.0
• Based on data as of 2003.
Longitude
Latitude
–5.0
97°W
33°N
+3.0
–6.0
–4.0
+7.0
+5.0
+1.0
–6.0
–6.0
+2.0
+11.0
+11.0
+2.0
+8.0
+3.0
+9.0
–9.0
–5.0
+3.0
+8.0
+4.0
+6.0
+9.0
+4.0
–3.0
–7.0
–4.0
+1.0
+1.0
–7.0
+2.0
+9.0
+11.0
–5.0
–4.0
+2.0
–2.0
–4.0
+5.0
+13.0
+4.0
+13.0
–5.0
–4.0
–8.0
+12.0
–10.0
–4.0
–9.0
+2.0
+9.0
+8.0
–3.0
+12.0
+0.0
+10.0
+4.0
+2.0
–7.0
–3.0
–2.0
–7.0
+10.0
+9.0
+9.0
+2.0
+11.0
+9.0
+10.0
+9.0
–7.0
+2.0
+8.0
+13.0
–5.0
36°E
105°W
83°W
90°E
55°E
6°W
114°W
106°W
9°E
154°E
145°E
10°E
106°E
25°E
114°E
158°W
95°W
29°E
107°E
39°E
67°E
102°E
48°E
68°W
115°W
77°W
9°W
0°E
118°W
4°W
121°E
145°E
99°W
80°W
9°E
56°W
74°W
59°E
177°E
37°E
167°E
90°W
74°W
165°W
166°E
171°W
80°W
150°W
2°E
116°E
105°E
62°W
168°E
24°W
126°E
47°E
13°E
122°W
71°W
47°W
122°W
127°E
121°E
104°E
18°E
151°E
121°E
140°E
107°E
123°W
16°E
103°E
175°E
97°W
34°N
40°N
42°N
24°N
25°N
53°N
54°N
32°N
50°N
28°S
13°N
54°N
21°N
60°N
22°N
21°N
30°N
41°N
6°S
22°N
25°N
3°N
29°N
17°S
36°N
12°S
39°N
52°N
34°N
40°N
15°N
38°S
19°N
26°N
45°N
35°S
46°N
24°N
18°S
1°S
1°S
30°N
41°N
64°N
22°S
14°N
9°N
18°S
49°N
32°S
12°N
11°N
18°S
15°N
39°N
25°N
42°N
38°N
33°S
24°S
48°N
38°N
31°N
1°N
59°N
34°S
25°N
36°N
48°N
49°N
48°N
18°N
41°S
50°N
4