Casio 3772 Watch User Manual

MO0505-EA
Operation Guide 3772
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
• This watch does not have a time zone that corresponds to the Greenwich
Mean Time differential of –3.5 hours. Because of this, the radio-controlled
timekeeping and World Time functions will not display the correct time for
Newfoundland, Canada.
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• Most of the display examples in this manual show only
the digital display, without the analog hands.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Stopwatch Mode
General Guide
Countdown Timer Mode
• Press C to change from mode to mode.
• In any mode, press B to illuminate the face of the watch.
▲
Timekeeping Mode
▲
World Time Mode
Press C.
▲
▲
▲
▲
Alarm Mode
Hand Setting Mode
Radio-controlled Atomic Timekeeping
To display the digital time and last signal screen
• In the Timekeeping Mode, press A to cycle through the digital time screens as
shown below.
• In the Timekeeping Mode, press D to display the last signal screen. The last signal
screen shows the time and date of the last successful time calibration signal
reception.
PM indicator
Press A.
▲
This watch receives a time calibration signal and updates
its time setting accordingly. The time calibration signal
includes both Standard Time and Daylight Saving Time
(summer time) data.
• This watch is designed to pick up the time calibration
signal transmitted in the United States (Fort Collins,
Colorado).
• The U.S. time calibration signal can be picked up by the
watch while in North America*.
term “North America” in this manual refers to the
* The
area that consists of Canada, the continental United
States, and Mexico.
Hour : Minutes
▲
Hour hand
Minute hand
A
Month – Day
Reception date
Day of week
Press D.
Seconds
Current Time Setting
This watch automatically adjusts its time setting in accordance with a time calibration
signal. You can also perform a manual procedure to set the time and date, when
necessary.
• The first thing you should do after purchasing this watch is to set your Home City,
which is the city where you will normally use the watch. For more information, see
“To set your Home City” below.
• When using the watch outside the ranges of the U.S. time signal transmitter, you
have to adjust the current time setting manually as required. See “Timekeeping” for
more information about manual time setting.
• The analog time of this watch is synchronized with the digital time. Because of this,
the analog time setting is automatically adjusted whenever you change the digital
setting. See “Analog Timekeeping” for more information.
To set your Home City
|||
|||
|||
|||
City code
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Use D (east) and B (west) to scroll through the city
codes until the one you want to use as your Home City
is displayed.
• The following are the city codes for major cities in
North America.
YVR: Vancouver
LAX: Los Angeles, San Francisco, Las Vegas,
Seattle/Tacoma, Tijuana
YEA: Edmonton
DEN: Denver, El Paso, Culiacan
MEX: Mexico City
YWG: Winnipeg
CHI: Chicago, Houston, Dallas/Fort Worth, New
Orleans
MIA: Miami
YTO: Toronto
New York, Detroit, Boston, Montreal
Halifax
St. Johns
• Note that this watch does not have a city code that corresponds to Newfoundland.
3. Press A to exit the setting screen.
• Normally, your watch should show the correct time as soon as you select your Home
City Code. If it does not, it should adjust automatically after the next auto receive (in
the middle of the night). You can also perform manual receive or you can set the time
manually.
• If you are in an area that does not use Daylight Saving Time (summer time), turn off
the DST setting.
Reception time
Last Signal
Screen
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
• Auto Receive
With auto receive, the watch automatically picks up the time calibration signal five
times a day at 0:00 a.m., 1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. For more
information, see “About Auto Receive”.
• Manual Receive
Manual receive lets you start a time calibration signal reception with the press of a
button. For more information, see “To perform manual receive”.
Important!
• When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o’clock side facing towards a window.
Make sure there are no metal objects nearby.
Resin Band
Metal Band
• The watch should not be on its side or facing the wrong way.
• Proper signal reception can be difficult or even impossible under the conditions listed
below.
NYC:
YHZ:
YYT:
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances,
office
equipment,
or a mobile
phone
Near a
Near highconstruction
tension
site, airport, or power lines
other sources
of electrical
noise
Among or
behind
mountains
1
Operation Guide 3772
• Signal reception is normally better at night than during the day.
• Time calibration signal reception takes from two to seven minutes, but in some
cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
600 miles
2,000 miles
Fort Collins
To turn auto receive on and off
1. In the Timekeeping Mode, press D to display the last
signal screen.
• The watch will automatically return to the Timekeeping
Mode if you do not perform any button operation for one
or two minutes after displaying the last signal screen.
2. Hold down A until the current auto receive setting
flashes on the display. This is the setting screen.
• If the auto receive setting does not appear when you
On/Off status
hold down A, it means that the city code currently
selected for the Home City is for an area that does not
support calibration signal reception. You cannot turn
auto receive on or off in this case.
3. Use D to turn auto receive on (ON) or off (OFF).
• Under good reception conditions, signal reception is possible within a radius of
about 2,000 miles (3,000 kilometers) from the Fort Collins transmitter.
• At distances further than about 600 miles (1,000 kilometers) from the Fort Collins
transmitter, signal reception may not be possible during certain times of year or
times of day. Radio interferance may also cause problems with reception.
• See the information under “Signal Reception Troubleshooting” if you experience
problems with time calibration signal reception.
4. Press A to exit the setting screen.
• To return to the Timekeeping Mode from the last signal screen, press D.
• For information about city codes that support signal reception, see “To set your
Home City”.
About Auto Receive
When auto receive is turned on, the watch automatically starts to receive the time
calibration signal when the time in the Timekeeping Mode reaches 0:00 a.m., 1:00
a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. each day (calibration times). The watch will
also perform an additional auto receive at 5:00 a.m. if none of the regularly scheduled
auto receive operations are successful.
When any auto receive is successful, the remaining auto receive operations are not
performed.
Problem
Probable Cause
What you should do
Cannot perform • The watch is not in the Timekeeping
• Enter the Timekeeping Mode
manual receive.
Mode.
and try again.
• Your current Home City is not one of the • Select YVR, LAX, YEA,
following city codes: YVR, LAX,
DEN, MEX, YWG, CHI,
YEA, DEN, MEX, YWG, CHI,
MIA, YTO, NYC, YHZ, or
MIA, YTO, NYC, YHZ, or YYT.
YYT as your Home City.
• Stop the countdown timer
• A countdown timer operation is in
progress.
operation.
Note
• Auto receive is performed only if the watch is in the Timekeeping Mode or World
Time Mode when one of the calibration times is reached. It is not performed if a
calibration time is reached while an alarm is sounding, or while you are configuring
settings (while settings are flashing on the display).
• Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can easily receive the signal.
• When auto receive is turned on, the watch receives the calibration signal for two to
seven minutes everyday when the time in the Timekeeping Mode reaches each of
the five calibration times. Do not perform any button operation within seven minutes
before or after any of the five calibration times. Doing so can interfere with correct
calibration.
• Remember that reception of the calibration signal depends on the time kept in the
digital display. Reception will be performed whenever the display shows one of the
five calibration times, regardless of whether or not the displayed time is actually the
correct time.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
Auto receive is
turned on, but
the Level 3
receiving
indicator does
not appear on
the display.
• You changed the time setting manually.
• You were performing some button
operation during the auto receive.
• Even if reception is successful, the
Level 3 receiving indicator disappears
every day at 0 a.m.
Time setting is
incorrect
following signal
reception.
• If the time is one hour off, the DST
• Change the DST setting to
setting may be incorrect.
Auto DST.
• The Home City code setting is not
• Select the correct Home City
correct for the area where you are using
code.
the watch.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
• For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Atomic Timekeeping Precautions”.
World Time
City code
Receiving indicator
Current time in
selected city
Weak
(Level 0)
Strong
(Level 3)
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal reception.
• The Level 3 receiving indicator remains on the display in all modes following
reception of the time calibration signal and calibration of the watch’s time setting.
The Level 3 receiving indicator is not displayed if signal reception was unsuccessful
or after manual adjustment of the current time setting.
• The Level 3 receiving indicator indicates that at least one of the five calibration
signal receive operations was successful. Note, however, that the Level 3 receiving
indicator is cleared from the display at 0:00 a.m. each day.
To perform manual receive
1. Place the watch on a stable surface so its top (12
o’clock side) is facing towards a window.
2. In the Timekeeping Mode, hold down D for about two
seconds until the watch beeps.
3. After you release D the display will show the current
time and the letters RC!. This indicates that signal
reception is in progress.
• Perform manual receive or
wait until the next auto signal
receive is performed.
• Check to make sure the
watch is in a location where it
can receive the signal.
The World Time Mode digitally displays the current time in
48 cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
• The watch will perform a signal reception even if it is in
the World Time Mode when a calibration time is
reached. If this happens, the World Time Mode time
settings will be adjusted in accordance with the
Timekeeping Mode’s Home City time.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city
While in the World Time Mode, press D to scroll through the city codes (time zones)
to the east.
• For full information on city codes, see the “City Code Table”
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
DST indicator
• Note that you cannot use the World Time Mode to change the DST setting of the
Home City code you currently have selected in the Timekeeping Mode. See “To
change the Daylight Saving Time (summer time) setting” for information about
turning the Home City code DST setting on and off.
• The DST indicator will appear on the display whenever you display a city code for
which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
• Time calibration signal reception normally takes from two to seven minutes. Take
care that you do not perform any button operations or move the watch during this
time.
• After signal reception is complete, the display of the watch changes to the last signal
screen.
Note
• To interrupt a reception and return to the Timekeeping Mode, press D.
• If reception is unsuccessful, the message ERR appears on the display for one or
two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the last signal or ERR screen to the normal timekeeping
screen by pressing D.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
2
Operation Guide 3772
Stopwatch
Minutes
Seconds
1/100 second
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Start
Alarm On Indicator / Hourly Time Signal On Indicator
Alarm Off
Signal Off
➤D
Stop
➤D
Re-start
➤D
Stop
➤A
Clear
Start
➤A
Split
➤A
Split release
➤D
Stop
➤A
Clear
An LED (light-emitting diode) and light guide panel
illuminate the digital display for easy reading in the dark.
• See “Illumination Precautions” for other important
information.
To turn on illumination
In any mode, press B to illuminate the display.
• You can specify 1.5 seconds or 2.5 seconds as the
illumination duration. See “To set the current digital time
and date manually” for more information.
Two Finishes
➤A
Split release
➤A
Clear
Display time of
second runner.
Countdown Timer
Minutes
Seconds
To set the countdown start time
1. While the countdown start time is on the display in the Countdown Timer Mode,
hold down A until the current countdown start time starts to flash, which indicates
the setting screen.
• If the countdown start time is not displayed, use the procedure under “To use the
countdown timer” to display it.
2. While a setting is flashing, use D (+) and B (–) to change it.
3. Press A to exit the setting screen.
PM indicator
Press A.
Hour : Minutes
A
Reception date
Press D.
Reception time
Last Signal
Screen
Setting the Digital Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the current digital time and date manually
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
|||
2. Press C to move the flashing in the sequence shown
below to select other settings.
|||
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm sounds for 10 seconds or until
you stop it by pressing any button. The countdown time is automatically reset to its
starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
• When setting the time, you can also configure settings for the illumination duration
and the 12/24-hour format.
• All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing C.
▲
You can set the countdown timer within a range of one to
60 minutes. An alarm sounds when the countdown
reaches zero.
• Calibration signal reception (both auto and manual) is
disabled while a countdown timer operation is in
progress.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Timekeeping
▲
Second runner
finishes.
|||
First runner
finishes.
Display time of
first runner.
|||
➤D
Stop
➤A
Split
D
Start
Alarm On
Signal On
Illumination
Split Time
D
Alarm Off
Signal On
Alarm On
Signal Off
• The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
Elapsed Time
D
To turn the Daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press D to cycle through the settings shown below.
Alarm
Alarm time
When the alarm is turned on, the alarm sounds when the
(Hour : Minutes) alarm time is reached. You can also turn on an Hourly
PM indicator
Time Signal, which will cause the watch to beep twice
every hour on the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
City code
City Code
DST
Day
12/24-Hour
Format
Month
Seconds
Year
Hour
Minutes
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
Screen:
Hourly time signal
on indicator
Alarm on indicator
To set the alarm time
1. In the Alarm Mode, hold down A until the hour setting of the alarm time starts to
flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
2. Press C to move the flashing between the hour and minute settings.
3. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
4. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
• To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To do this:
Do this:
Change the city code
Use D (east) and B (west).
Cycle between Daylight Saving Time
(ON), Standard Time (OFF), and
Auto DST (A t )
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Reset the seconds to 00
Toggle the illumination duration
setting between 1.5 seconds ( ) and
2.5 seconds ( )
Press D.
Change the hour or minutes
Use D (+) and B (–).
Press D.
Press D.
Press B.
Change the year
Change the month or day
• See “City Code Table” for a complete list of available city codes.
• For information about settings other than the time and date, see the following.
Illumination duration: Illumination
3
Operation Guide 3772
Reference
4. Press A to exit the setting screen.
• When you exit the setting screen, the analog hands are adjusted automatically to
match the digital time. See “Analog Timekeeping” for more information.
Note
• Auto DST (A t ) can be selected only while HNL, ANC, YVR, LAX, YEA,
DEN, MEX, YWG, CHI, MIA, YTO, NYC, YHZ, YYT, HKG, SEL, or
TYO is selected as the Home City code. For more information, see “Daylight Saving
Time (DST)” below.
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display
Auto Display continually changes the contents of the
digital display.
To turn off Auto Display
Press any button to turn off Auto Display. This returns to
the Timekeeping Mode.
To turn on Auto Display
In the Timekeeping Mode, hold down C for about two
seconds until the watch beeps.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the digital time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight Saving Time.
The time calibration signal transmitted from Fort Collins includes both Standard Time
and DST data. When the Auto DST setting is turned on, the watch switches between
Standard Time and DST (summer time) automatically in accordance with the Fort
Collins signal.
• The default DST setting is Auto DST (A t ) whenever you select ANC, YVR,
LAX, YEA, DEN, MEX, YWG, CHI, MIA, YTO, NYC, YHZ, YYT, or
TYO as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it is
probably best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
indicates the setting screen.
2. Press C once and the DST setting screen appears.
3. Use D to cycle through the DST settings in the sequence shown below.
Auto DST (A
t
)
DST off (OFF)
DST on (ON)
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator (
) appears on the display to indicate that Daylight Saving
Time is turned on.
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
• The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting manually
When the digital time setting is changed by time calibration signal reception
When you change the Home City code and/or DST setting
• If the analog time does not match the digital time for any reason, use the procedure
described under “To adjust the analog time” to match the analog setting to the digital
setting.
• Whenever you need to adjust both the digital and the analog time settings manually,
make sure you adjust the digital setting first.
• Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
To adjust the analog time
|||
|||
|||
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the setting screen.
3. Use D and B to adjust the analog setting as
described below.
|||
When you want to do this:
Move the hand setting
forward 20 seconds
Move the hand setting a short
way forward at high speed
Move the hand setting a long
way forward at high speed
Perform this button operation:
• Press D.
• Hold down D.
• Release D when the hands reach the setting
you want.
• While holding down D to move the hands at
high speed, press B to lock the high-speed
hand movement.
• To stop the hand movement, press any
button.
• Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.
4. Press A to exit the setting screen.
• The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
• To return to the Timekeeping Mode, press C.
Note
• Calibration signal reception is disabled while Auto
Display is being performed.
• Auto Display cannot be performed while a setting screen
is on the display.
Auto Return Features
• If you leave the watch in the Alarm or Hand Setting Mode for two or three minutes
without performing any operation, it automatically returns to the Timekeeping Mode.
• If you leave the watch with a flashing setting on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Initial Screens
When you enter the World Time Mode, the data you were viewing when you last exited
the mode appears first.
Radio-controlled Atomic Timekeeping Precautions
• Strong electrostatic charge can result in the wrong time being set.
• Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• The time calibration signal bounces off the ionosphere. Because of this, such factors
as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make manually.
• The watch is designed to automatically update the date and day of the week for the
period January 1, 2000 to December 31, 2099. Setting of the date by the time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps time within ±15 seconds a month at normal temperature.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your current city code, DST (summer
time), and auto receive settings. The following are the initial factory defaults for these
settings.
Setting
Initial Factory Default
City code
NYC (New York)
DST (summer time)
(Auto switching)
Auto receive
(Auto receive)
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Greenwich Mean Time (GMT) differential for each
city, based on your Home City time setting.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC*) data.
* UTC is the world-wide scientific standard of timekeeping. It is based upon carefully
maintained atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s rotation.
The reference point for UTC is Greenwich, England.
12-hour/24-hour Timekeeping Formats
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes.
• With the 12-hour format, the PM indicator (P) appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
Illumination Precautions
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination automatically turns off whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
4
Operation Guide 3772
City Code Table
City
Code
City
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
YWG
CHI
MIA
YTO
NYC
CCS
YHZ
YYT
RIO
RAI
LIS
LON
BCN
MAD
PAR
MIL
ROM
BER
STO
ATH
CAI
JRS
MOW
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Winnipeg
Chicago
Miami
Toronto
New York
Caracas
Halifax
St. Johns
Rio De Janeiro
Praia
Lisbon
London
Barcelona
Madrid
Paris
Milan
Rome
Berlin
Stockholm
Athens
Cairo
Jerusalem
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
HKG
Hong Kong
SEL
TYO
ADL
GUM
SYD
NOU
WLG
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
GMT
Differential
–11.0
–10.0
–09.0
Other major cities in same time zone
–08.0
Papeete
Nome
San Francisco, Las Vegas,
Seattle/Tacoma, Dawson City, Tijuana
–07.0
El Paso, Culiacan
–06.0
Houston, Dallas/Fort Worth, New Orleans
–05.0
Montreal, Detroit, Boston,
Panama City, Havana, Lima, Bogota
–04.0
La Paz, Santiago, Port Of Spain
–03.5
–03.0
–01.0
Sao Paulo, Buenos Aires, Brasilia, Montevideo
+00.0
Dublin, Casablanca, Dakar, Abidjan
+01.0
Amsterdam, Algiers, Hamburg, Frankfurt, Vienna
+02.0
Helsinki, Istanbul, Beirut, Damascus,
Cape Town
+03.0
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi
+03.5
+04.0
+04.5
+05.0
+05.5
+06.0
+06.5
+07.0
Shiraz
Abu Dhabi, Muscat
Male
Mumbai, Kolkata
Colombo
+08.0
Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Beijing, Taipei, Manila, Perth,
Ulaanbaatar
+09.0
Pyongyang
+09.5
Darwin
+10.0
Melbourne, Rabaul
+11.0
+12.0
Port Vila
Christchurch, Nadi, Nauru Island
• Based on data as of December 2004.
5