Casio 5192 Watch User Manual

MA1011-EA
Operation Guide 5192
ENGLISH
Congratulations upon your selection of this CASIO watch.
E-1
About This Manual
B
@
+
Things to check before using the watch
Button operations are indicated using the letters A through
D shown in the illustration.
Hand Functions
1. Hold down C for about two seconds to enter the Timekeeping Mode, and
then observe the movement of the x Second Hand.
z
x
c
v
>
*
6
5
Hour Hand
Second Hand
Minute Hand
Left Dial Hand:
Indicates the current day of the week and current mode.
b 24-hour Hand:
Indicates the current 24-hour timekeeping hour.
The long end indicates the current hour between 18:00
and 6:00. The short end indicates the current hour
between 6:00 and 18:00.
Is the x Second Hand moving smoothly at one-second intervals?
NO
Is the x Second Hand moving at
two-second intervals or is it stopped
completely?
YES
The watch is charged sufficiently.
For details about charging, see
“Charging the Watch” (page E-8).
NEXT
YES
Power is low. Charge the watch by placing
it in a location where it is exposed to light.
For details, see “Charging the Watch”
(page E-8).
n Right Dial Hands: Indicate a time, in 24-hour format, depending on the current mode.
m Day
This User’s Guide uses numbers shown above to identify watch hands and indicators.
Go to step 2.
E-2
E-3
2. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To configure Home City settings” (page E-20) to configure
your Home City and daylight saving time settings.
Important!
Proper World Time setting depend on correct Home City, time, and date settings in
the Timekeeping Mode. Make sure you configure these settings correctly.
3. Set the current time.
x To set the time
See “Configuring Current Time and Date Settings” (page E-25).
The watch is now ready for use.
Contents
E-2
About This Manual
E-3
Things to check before using the watch
E-8
Charging the Watch
E-15 To recover from the sleep state
E-16 Mode Reference Guide
E-17 To determine the watch’s current mode
E-17 To return to the Timekeeping Mode from any other mode
E-18 To select a mode
E-19 Timekeeping
E-20 Configuring Home City Settings
E-20 To configure Home City settings
E-4
E-5
E-23
To toggle the Home City time between standard time and daylight
saving time
E-25 Configuring Current Time and Date Settings
E-25 To change the current time setting
E-29 To change the current date setting
E-45
E-45
E-45
To change the alarm time setting
To turn the alarm on or off
To stop the alarm
E-46 Adjusting Home Positions
E-47 To adjust home positions
E-34 Using the Stopwatch
E-34 To perform elapsed time measurement
E-35 To perform an elapsed time operation
E-35 To pause at a split time
E-51 Troubleshooting
E-56 Specifications
E-38 Checking the Current Time in a Different Time Zone
E-39 To view the time in another time zone
E-40 To specify standard time or daylight saving time (DST) for a time
zone
E-42 To swap your Home City and World Time City
E-44 Using the Alarm
E-6
E-7
Charging the Watch
The face of the watch is a solar cell that generates power from light. The generated
power charges a built-in rechargeable battery, which powers watch operations. The
watch charges whenever it is exposed to light.
Charging Guide
Whenever you are not
wearing the watch, leave
it in a location where it is
exposed to light.
x Best charging
performance is achieved
by exposing the watch to
light that is as strong as
possible.
E-8
When wearing the watch,
make sure that its face is
not blocked from light by the
sleeve of your clothing.
x The watch may enter a
sleep state (page E-14) if
its face is blocked by your
sleeve even only partially.
Warning!
Leaving the watch in bright light for charging can cause it to become quite hot.
Take care when handling the watch to avoid burn injury. The watch can become
particularly hot when exposed to the following conditions for long periods.
x On the dashboard of a car parked in direct sunlight
x Too close to an incandescent lamp
x Under direct sunlight
Important!
x Keep the watch in an area normally exposed to bright light when storing it for long
periods. This helps to ensure that power does not run down.
x Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause power to run down.
Make sure that the watch is exposed to bright light whenever possible.
E-9
Operation Guide 5192
Power Levels
B
Level
+
@
You can get an idea of the watch’s power level by
observing the movement of the x Second Hand in the
Timekeeping Mode.
x If the x Second Hand is moving normally at one-second
intervals, power is at Level 1.
x If the x Second Hand is moving at two-second intervals,
power is at Level 2, which is quite low. Expose the watch
to light as soon as possible so it can charge.
5
Moves at two-second
intervals.
Hand Movement
Function Status
1
Normal.
All functions enabled
2
x Second Hand moves at two-second
intervals.
m Day changes to 1 (home position).
Beeper disabled
3
x Second Hand stopped.
z Hour Hand and c Minute Hand
stopped at 12 o’clock.
All functions disabled
x When power drops to Level 3, all functions will be disabled but the watch will
continue to keep time internally for about one week. If you recharge the battery
sufficiently during this period, the analog hands will move automatically to the
correct setting and regular timekeeping will resume. After one week, all settings
(including timekeeping) will be cleared. Recharging the battery will reset all settings
to their initial factory defaults.
E-10
E-11
Power Recovery Mode
Charging Times
The watch is designed to go into a power recovery mode that stops hand operation
temporarily whenever power suddenly drops below a certain level due to overuse
of the alarm tone over a short period. Note that all operations are disabled while the
watch is in the power recovery mode.
The hands will move to the correct positions and the watch will resume normal
operation after power recovers (in about 15 minutes). Putting the watch in a location
where it is exposed to light will help power to recover sooner.
Exposure Level (Brightness)
Daily
Operation
*1
Level Change *2
Level 3
Level 2
Level 1
Outdoor sunlight (50,000 lux)
8 minutes
2 hours
27 hours
Window sunlight (10,000 lux)
30 minutes
6 hours
100 hours
Window sunlight on cloudy day
(5,000 lux)
48 minutes
10 hours
–––
8 hours
112 hours
–––
Indoor fluorescent lighting (500 lux)
* 1 Approximate exposure each day to generate power for normal daily operation.
* 2 Approximate exposure to take power up one level.
x The above times are for reference only. Actual times depend on lighting conditions.
x For details about the operating time and daily operating conditions, see the “Power
Supply” section of the Specifications (page E-57).
E-12
E-13
Power Saving
Power Saving enters a sleep state automatically whenever the watch is left for a
certain period in an area where it is dark. The table below shows how watch functions
are affected by Power Saving.
x There actually are two sleep state levels: “second hand sleep” and “function sleep”.
Elapsed Time in Dark
Operation
60 to 70 minutes (second hand sleep)
x Second Hand only stopped at 12 o’clock, all
other functions enabled
6 or 7 days (function sleep)
x All functions, including analog timekeeping,
disabled
x Internal timekeeping maintained
To recover from the sleep state
Move the watch to a well-lit area or press any button.
x The watch will not enter a sleep state between 6:00 a.m. and 9:59 p.m. If the watch
is already in a sleep state when 6:00 a.m. arrives, however, it will remain in the
sleep state.
x The watch will not enter a sleep state while it is in the Stopwatch Mode.
E-14
E-15
Mode Reference Guide
Your watch has four “modes”. The mode you should select depends on what you
want to do.
Enter this mode:
See:
x View the current time in your Home City and in one of 29 other
cities around the globe
x View the current date in the Home City
x Configure Home City and daylight saving time (DST) settings
x Configure time and date settings
Timekeeping
Mode
E-19
Use the stopwatch to measure elapsed time
Stopwatch Mode
E-34
x Select one of 29 cities (time zones) around the world and view
the current time there
x Select daylight saving/summer time (DST) or standard time
for a time zone
World Time Mode
E-38
Set an alarm time
Alarm Mode
E-44
To determine the watch’s current mode
Check the position of the v Left Dial Hand as shown
under “To select a mode” (page E-18).
To return to the Timekeeping Mode from any other
mode
Hold down C for about two seconds until the x Second
Hand returns to 12 o’clock.
To do this:
Selecting a Mode
With this watch, everything starts from the Timekeeping Mode.
> @
E-16
E-17
To select a mode
Press C to cycle between the modes as shown below. The v Left Dial Hand
indicates the currently selected mode.
C
Timekeeping Mode
The hand indicates the day
of the week (SU, MO, TU,
WE, TH, FR, SA).
Timekeeping
Use the Timekeeping Mode to view the current time and date. To enter the
Timekeeping Mode from any other mode, hold down C for about two seconds.
Stopwatch Mode
B
@
+
The hand points to 0.
Alarm Mode
The hand points to ALM.
E-18
>
World Time Mode
The hand points to STD
or DST.
>
*
6
5
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
v Left Dial Hand: Indicates the day of the week.
b 24-hour Hand:
Indicates the current 24-hour timekeeping hour. The long
end indicates the current hour between 18:00 and 6:00.
The short end indicates the current hour between 6:00
and 18:00.
n Right Dial Hands:
Indicate the current time in the World Time City (page
E-38) in 24-hour format.
m Day
E-19
Operation Guide 5192
x For details about city codes, see the “City Code Table” at the back of this
manual.
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
B
2. To change the Home City setting, press D to move the
x Second Hand clockwise.
x Keep pressing D until the x Second Hand is pointing
at the city code you want to select as your Home City.
x Each time you change the city code setting, the
z Hour Hand, c Minute Hand, b 24-hour Hand and
m Day move to the current time and date for that city
code. Do not perform the next operation until these
hands stop moving.
+
To configure Home City settings
Note
x This watch does not have a city code that corresponds
to Newfoundland.
1. In the Timekeeping Mode, keep A depressed (for about
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
x This is the city code setting mode.
x The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
@
>
*
@ 5
E-20
E-21
3. Press B to toggle the time for the currently selected city code between STD
(standard time)/DST (daylight saving time).
x While you are selecting the Home City code, the v Left Dial Hand will indicate
whether the currently selected city code is configured for standard time (STD) or
daylight saving/summer time (DST).
x Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
4. After all the settings are the way you want, press A to return to the Timekeeping
Mode.
To toggle the Home City time between standard time and daylight saving time
1. Perform the step 3 under “To configure Home City settings” on page E-20.
x Each time you select a city code, the z Hour Hand, c Minute Hand, and
b 24-hour Hand move to the current time for that city code. Do not perform the
next operation until these hands stop moving.
x While you are selecting the Home City code, the v Left Dial Hand will indicate
whether the currently selected city code is configured for standard time (STD) or
daylight saving/summer time (DST).
2. Press B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
x Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
3. After the setting is the way you want, press A to return to the Timekeeping Mode.
E-23
E-22
Note
x After you specify a city code, the watch will use UTC* offsets to calculate the World
Time based on the current time in your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping. The
reference point for UTC is Greenwich, England.
Configuring Current Time and Date Settings
You can configure current time and date settings in the Timekeeping Mode.
To change the current time setting
1. In the Timekeeping Mode, keep A depressed (for about
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
x The v Left Dial Hand will indicate whether the
currently selected city code is configured for standard
time (STD) or daylight saving/summer time (DST).
>
@
E-24
E-25
2. Change the Home City and daylight saving time (DST) settings, if you want.
x For details about these settings, see steps 2 and 3 under “To configure Home
City settings” (page E-20).
x In the following steps, each press of C cycles between settings as shown
below.
Home city/DST
Hour/Minute
B
4. Use D (+) and B (–) to change the time (hour and
minute) setting.
x Each press of either button will move the hands
(z Hour Hand and c Minute Hand) one minute.
x Holding down D or B will start high-speed z Hour
Hand and c Minute Hand movement in the applicable
direction. To stop high-speed hand movement, press
any button.
x The b 24-hour Hand and z Hour Hand move in sync
with each other.
x When setting the time, make sure that the b 24-hour
Hand indicates the proper a.m./p.m. hour.
Year
(tens digit)
Year
(ones digit)
Day
3. Press C.
x The x Second Hand will move to 12 o’clock. This is
the time setting mode.
@ +
*
Month
E-26
x If you want to change the date setting at this time, press C and perform the
procedure starting from step 3 under “To change the current date setting” (page
E-29).
E-27
To change the current date setting
@
00
5. After the time setting is the way you want, press A to return to regular
timekeeping.
x This will cause the x Second Hand to move automatically to 12 o’clock and
resume movement from there.
10
20
90
30
80
40
70
1. In the Timekeeping Mode, keep A depressed
(for about five seconds) as the x Second Hand
moves to the city code of the currently selected
Home City.
2. Press C twice.
x The x Second Hand will move to the tens digit
of the current year setting. This is the year
setting mode.
x The year can be set in the range of 2000 to
2099.
50
60
Setting the year (tens digit)
E-28
E-29
Operation Guide 5192
3. Press D to move the x Second Hand clockwise
until it is pointing at the year tens digit you want
to select.
@
0
1
4. After you select the year tens digit, press C.
x The x Second Hand will move to the ones digit
of the current year.
2
9
3
8
4
5. Press D to move the x Second Hand clockwise
until it is pointing at the year ones digit you want
to select.
Dec
Jan
Nov
Feb
Oct
Sep
Mar
Apr
Aug
Jul
7
5
6
Setting the year (ones digit)
@
May
6. After you select the year ones digit, press C.
x The x Second Hand will move to the currently
selected month. This is the month setting
mode.
7. Use D to move the x Second Hand to the
month setting you want.
8. After the month setting is the way you want,
press C.
x The x Second Hand will move to 12 o’clock,
and the watch will enter the day setting mode.
Jun
Setting the month
E-30
E-31
9. Use D (+) and B (–) to change the m Day setting.
x If you want to change the time setting at this time,
press C and then perform the procedure starting
from step 3 under “To change the current time setting”
(page E-25).
@
>
5
Note
x The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s rechargeable battery replaced or after
power drops to Level 3.
10. After the settings are the way you want, press A to
return to regular timekeeping.
x This will cause the x Second Hand to move
automatically to 12 o’clock and resume movement
from there.
x The day of the week indicated by the v Left Dial
Hand changes automatically in accordance with the
date (year, month, and day).
E-32
E-33
Using the Stopwatch
The stopwatch measures elapsed time and split times.
Hand Functions
x Second Hand: Indicates the stopwatch 1/10-second
count.
v Left Dial Hand: Indicates the stopwatch 1/100-second
count.
n Right Dial Hands: Indicate the stopwatch minutes and
seconds.
@
>
6
To perform elapsed time measurement
1. Use C to move the v Left Dial Hand to 0.
x This indicates the Stopwatch Mode.
2. Now you can perform either of following stopwatch operations.
x You will not be able to perform any stopwatch operation while the hands are
moving to their initial positions after you enter the Stopwatch Mode.
To perform an elapsed time operation
B
B
Start
B
Stop
(Restart)
B
D
(Stop)
Reset
To pause at a split time
B
Start
D
Split
Normal stopwatch hand movement will
resume automatically after five seconds.
B
Stop
D
Reset
E-34
E-35
Note
x The Stopwatch Mode can indicate elapsed time up to 23 minutes, 59.99 seconds.
x In the following cases, the hands of the watch are moving, so pressing D or B will
not perform any stopwatch operation.
− While the hands are moving to elapsed timekeeping after you enter the Stopwatch
Mode
− While the watch is changing dates at midnight
x Once started, stopwatch timing continues until you press B to stop it, even if you
exit the Stopwatch Mode to another mode or timing reaches the stopwatch limit
defined above.
x Whenever you enter the Stopwatch Mode, the hands of the watch move to their
initial Stopwatch Mode positions. If you did not reset the stopwatch the last time you
used it, the hands will return to the positions they were in the last time you exited
the Stopwatch Mode.
x The x Second Hand indicates the 1/10-second count for the first 30 seconds of
a stopwatch elapsed time operation. After that, the hand stops at 0. 1/10-second
timing continues internally after the first 30 seconds, and the x Second Hand will
jump to the current value whenever B (Stop) or D (Split) is pressed.
x Though the v Left Dial Hand is stopped while an elapsed time measurement
operation is in progress, the watch keeps track of the 1/100-second count
internally. The v Left Dial Hand will jump to the current 1/100-second reading
whenever you stop the stopwatch or perform a split time operation (page E-35).
E-36
E-37
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 29 time
zones around the globe. Each time zone has a “city code”, which is a three-letter
abbreviation of a representative city in the zone. The representative city of the time
zone that is currently selected in the World Time Mode is called the “World Time City”.
Hand Functions
x Second Hand: Indicates the currently selected World
Time City.
v Left Dial Hand: Indicates the current STD (standard
time) or DST (daylight saving time)
setting of the currently selected World
Time City.
n Right Dial Hands: Indicate the current time in the
selected World Time City in 24-hour
format.
@
>
E-38
To view the time in another time zone
1. Use C to move the v Left Dial Hand to STD or DST.
x This indicates the World Time Mode.
2. Use D to move the x Second Hand to the city code you want to select as the
World Time City.
x The n Right Dial Hands will move to the current time in the currently selected
World Time City. At this time, the z Hour Hand and c Minute Hand will continue
to indicate the current time in the Home City.
x For full information on city codes, see the “City Code Table” at the back of this
manual.
x If you think that the time indicated for the selected World Time City is not correct,
it probably means that there is something wrong with your Home City settings.
Use the procedure under “To configure Home City settings” (page E-20) to
correct the Home City settings.
6
E-39
Operation Guide 5192
To specify standard time or daylight saving time (DST) for a time zone
1. In the World Time Mode, use D to select the city code
for the time whose setting you want to change.
x Wait until the n Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
>
6
Hold down
A for two
seconds
2. Hold down A for about two seconds until the watch
beeps. This will cause the v Left Dial Hand to toggle
between DST (daylight saving time) and STD (standard
time).
x Note that you cannot switch between STD (standard
time)/DST (daylight saving/summer time) while UTC is
selected as the World Time City.
x Note that the STD (standard time)/DST (daylight
saving/summer time) setting affects only the currently
selected time zone. Other time zones are not affected.
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
capability can come in handy when you frequently travel between two locations in
different time zones.
The following example shows what happens when the Home City and World Time
City are swapped while the Home City originally is TYO (Tokyo) and the World Time
City is NYC (New York).
Before swapping
After swapping
Home City
World Time City
Tokyo
10:08 p.m.
(Standard time)
New York
9:08 a.m.
(Daylight saving time)
New York
9:08 a.m.
(Daylight saving time)
Tokyo
10:08 p.m.
(Standard time)
E-40
E-41
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World
Time City you want.
x In this example, you would move the x Second Hand
to NYC in order to select New York as the World
Time City.
x Wait until the n Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
@
@
6
6
2. Hold down B for about three seconds until the watch
beeps.
x This will make the World Time City (NYC in this
example) your new Home City. At the same time, it
will change the Home City you had selected prior to
step 2 (TYO in this example) to your World Time City.
x After swapping the Home City and World Time City,
the watch will stay in the World Time Mode. The
x Second Hand will point to your new World Time City
(TYO in this example).
x The n Right Dial Hands will indicate the current time
in your new World Time City.
E-42
E-43
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
@
>
Hand Functions
x Second Hand: Indicates the current alarm ON/OFF
setting.
v Left Dial Hand: Points to ALM.
n Right Dial Hands: Indicate the current alarm time
setting in 24-hour format.
To change the alarm time setting
1. Use C to move the v Left Dial Hand to ALM.
x This indicates the Alarm Mode.
2. Use D (+) and B (–) to change the alarm time setting.
x Each press of either button will move the n Right Dial Hands one minute.
x Holding down D or B will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
x The alarm always works based on the time kept in the Timekeeping Mode.
x The watch will return to the Timekeeping Mode automatically if you do not
perform any operation in the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm on and off. The x Second Hand will
indicate the current ON/OFF setting.
To stop the alarm
Press any button.
6
E-44
E-45
Adjusting Home Positions
Strong magnetism or impact can cause the hands and/or date of the watch to be off.
If this happens, perform the applicable home position adjustment procedures in this
section.
x Hand home position adjustment is not required if the time and day settings are
correct.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in the home position adjustment mode. In either case,
any adjustments you made before the watch returned to the Timekeeping Mode will
be applied.
To adjust home positions
1. Hold down C for about two seconds until the x Second
B @ +
Hand stops and then starts moving again.
>
*
6
5
E-46
2. Hold down D for about three seconds.
x The x Second Hand will start to move when you first
press D. Keep D depressed until the x Second
Hand stops.
x The watch is now in the home position adjustment
mode.
x The watch will exit the home adjustment mode
automatically if you do not perform any operation for
about two or three minutes.
x First is x Second Hand home position adjustment.
x If the x Second Hand moves to 12 o’clock, it is in the
correct home position. If it doesn’t, use D to move it
to 12 o’clock.
E-47
x When adjusting a hand or the date home position, it is recommended that after
you move to a proper home position, you press B to move the setting back one
step. Next, press D again to return it to the home position. This helps to ensure
better home position adjustment accuracy.
x Each press of C in the home position adjustment mode will cycle through the
adjustment settings as shown below.
x Second
z Hour/ c Minute/ b 24-hour
B @ +
n Right Dial Hands
m Day
v Left Dial Hand
*
6
3. After confirming that the x Second Hand is at the proper
home position, press C. This will switch to z Hour
Hand and c Minute Hand home position adjustment.
x The z Hour Hand and c Minute Hand are at their
proper home positions if they both move to 12 o’clock.
The b 24-hour Hand also will move along with
z Hour Hand movement, and cannot be adjusted
individually. If the hands are not positioned correctly,
use D (+) and B (–) to move them to their proper
home positions.
4. After confirming that the z Hour Hand and c Minute
Hand are in their correct home positions, press C.
This will switch to n Right Dial Hands home position
adjustment.
x The n Right Dial Hands are at their proper home positions if they both move
to 24. If the hands are not positioned correctly, use D (+) and B (–) to move
them to 24.
E-48
E-49
Operation Guide 5192
>
6
5
5. After confirming that the n Right Dial Hands are in the
correct home position, press C. This will advance to
v Left Dial Hand home position adjustment.
x The v Left Dial Hand is in the correct home position if
it is pointing at 12 o’clock. If it isn’t, use D (+) and B
(–) to move it to 12 o’clock.
6. After confirming that the v Left Dial Hand is in the
correct home position, press C. This will advance to
day home position adjustment.
x The m Day is in the correct home position if it shows
1. If it doesn’t, use D (+) and B (–) to change the
day to 1.
7. Press A to return to the Timekeeping Mode.
x The m Day moves to the current day, and then the z Hour Hand and the
c Minute Hand will move to the current time. Wait until everything stops moving.
Troubleshooting
Hand Movement and Position
■ I lost track of what mode the watch is in.
Refer to “To select a mode” (page E-18). To return directly to the Timekeeping Mode
from any other mode, hold down C for about two seconds.
■ The x Second Hand is moving at two second intervals.
■ All the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the x Second Hand starts moving
normally, at one-second intervals (page E-10).
■ The hands of the watch suddenly start moving at high speed, even when I do
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
x The watch is recovering from a sleep state (page E-14).
E-50
E-51
x The watch is returning to the Timekeeping Mode automatically from the Alarm Mode
(page E-44).
■ Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode (page E-12). Do not perform any
operation until the hands return to their normal positions (in about 15 minutes). The
hands should return to their correct positions when power recovers. To help power
recover, leave the watch in a location where it is exposed to light.
■ The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it, if
necessary (page E-20).
■ The current time setting is off by one hour.
You may need to change your Home City’s STD (standard time)/DST (daylight
saving/summer time) setting. Use the procedure under “To toggle the Home City time
between standard time and daylight saving time” (page E-23) to change the STD/
DST setting.
■ The hands and/or day indications are off.
This could indicate that the watch has been exposed to magnetism or strong impact,
which has caused problems with proper hand and day alignment. Adjust the watch’s
hand and day home position alignment (page E-46).
E-52
E-53
World Time Mode
■ The World Time indicated by the n Right Dial Hands in the World Time Mode is
one hour off from the actual time in the selected World Time City.
The STD (standard time)/DST (daylight saving/summer time) setting of the selected
World Time City may be wrong. Select the correct STD (standard time)/DST (daylight
saving/summer time) setting (page E-40).
■ The World Time indicated by the n Right Dial Hands in the World Time Mode
is off.
Your Home City settings may be wrong. Check your Home City settings and correct
them, if necessary (page E-20).
Charging
■ The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3 (page E-10). Continue
exposing the watch to light until the x Second Hand starts moving normally (at onesecond intervals).
■ The x Second Hand starts to move at one-second intervals, but then suddenly
returns to moving at two-second intervals.
The watch probably is not sufficiently charged yet. Continue keeping it exposed to
light.
E-54
E-55
Specifications
Accuracy at normal temperature: ±15 seconds a month
Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds, 24-hour,
day, day of the week
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 29 city codes and Coordinated
Universal Time); Daylight Saving Time (summer time) / Standard Time
Stopwatch: Measuring capacity: 23'59.99"
Measuring unit: 1/100 second
Measuring mode: Elapsed time, split time
World Time: 29 cities (29 time zones) and Coordinated Universal Time
Other: Standard Time/Daylight Saving Time (summer time); Home City/World Time
City swapping
Alarm: Daily alarm
Other: Power Saving
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 6 months (no exposure to light after a full
charge; 10 seconds alarm beeper operation)
E-56
E-57
City Code Table
City
UTC Offset/
City
Code
GMT Differential
PPG
Pago Pago
–11
HNL
Honolulu
–10
ANC
Anchorage
–9
LAX
Los Angeles
–8
DEN
Denver
–7
CHI
Chicago
–6
NYC
New York
–5
SCL
Santiago
–4
RIO Rio De Janeiro
–3
FEN Fernando de Noronha
–2
RAI
Praia
–1
UTC
0
LON
London
PAR
Paris
+1
ATH
Athens
+2
L
City
Code
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
HKG
TYO
ADL
SYD
NOU
WLG
City
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
Hong Kong
Tokyo
Adelaide
Sydney
Noumea
Wellington
UTC Offset/
GMT Differential
+3
+3.5
+4
+4.5
+5
+5.5
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
xBased
on data as of July 2010.
xThe
rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
L-1