BCX-14G, BCX-14E, BX-14G, BX-14E, CNVX-14G aNd CNVX-14E INSTaLLaTION - OPERaTION - MaINTENaNCE

BCX-14G, BCX-14E, BX-14G, BX-14E, CNVX-14G aNd CNVX-14E INSTaLLaTION - OPERaTION - MaINTENaNCE
BCX-14G, BCX-14E, BX-14G, BX-14E,
CNVX-14G and CNVX-14E
INSTALLATION - OPERATION - MAINTENANCE
BLODGETT OVEN COMPANY
www.blodgett.com
44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: (802) 658-6600 Fax: (802)864-0183
PN 39678 Rev W (3/13)
© 2013 - G.S. Blodgett Corporation
Your Service Agency’s Address:
Model
Serial number
Oven installed by
Installation checked by
TABLE OF CONTENTS
IMPORTANT
WARNING: Improper installation, adjustment, alternation,
service or maintenance can
cause property damage, injury or death. Read the instllation, operation and maintenance instructions thoroughly
before installing or servicing
this equipment.
INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE
USER SMELLS GAS MUST BE
POSTED IN A PROMINENT LOCATION. This information may
be obtained by contacting your
local gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or any
other appliance.
INSTALLATION
The Blodgett Combi-Oven/Steamer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of the Combi-Oven/Steamer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Owner’s Responsibilities.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Utility Connections - Standards and Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Oven Location and Ventilation.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Leg Attachment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Caster Attachment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Deliming System Connection and Priming (BCX-14 units only). . . . . . . . . . . . . . . . 9
Plumbing Connections.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Gas Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Gas Hose Restraint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Final Check Lists.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OPERATION
Safety Information for Gas Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Power Switches.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Standard Controls for Models BCX-14 and BX-14. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
The information contained in this
manual is important for the proper installation, use, and maintenance of this oven. Adherence
to these procedures and instructions will result in satisfactory
baking results and long, trouble free service. Please read
this manual carefully and retain
it for future reference.
ERRORS: Descriptive, typographic or pictorial errors are
subject to correction. Specifications are subject to change
without notice.
MenuSelect™ Control for Models BCX-14 and BX-14. . . . . . . . . . . . . . . . . . . . . . . 21
Standard Controls for Models CNVX-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MenuSelect™ Control for Model CNVX-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SmartTouch Touchscreen Control for Model BX-14. . . . . . . . . . . . . . . . . . . . . . . . . . 34
MAINTENANCE
Spray Bottle Operating Procedure...................................................................... 48
Cleaning and Preventive Maintenance................................................................ 49
Daily Cleaning............................................................................................... 49
Preventive Maintenance............................................................................... 49
BX-14 Boilerless Oven Weekly Cleaning...................................................... 50
Flushing the Boiler - BCX Models Only............................................................... 51
Deliming.............................................................................................................. 52
BCX Combi Ovens........................................................................................ 52
BX-14 Boilerless Oven.................................................................................. 55
Deliming Interval Setting - BCX Only............................................................ 56
Installation
The Blodgett Combi-Oven/Steamer
You can also use two or three functions in sequence
during one cooking process. We call this:
The Blodgett Combi-Oven/Steamer offers a completely
new method of cooking. With the Oven/Steamer you have
the choice of two cooking processes: Steam and Hot Air,
either...
•
combi-steaming
•
Separately
•
combi-roasting
•
Combined, or
•
combi-baking
•
In Sequence
The combination of circulating hot air and steam in the
space saving, high performance Combi-Oven/Steamer
leads to improvements in the following areas:
And for easy operation you can choose from three modes:
•
increased productivity in the kitchen
•
a reduction in capital expenditures for multiple equipment replacement
•
a wider range of menu choices
•
a simplified cleaning process
The work process is simplified since products are prepared on or in steam table pans and trays. Food can be
cooked, stored, and transported with the same pans.
Small amounts of product can be processed efficiently;
pre-cooked and convenience foods can be reheated within minutes. Many frozen foods can be processed without pre-thawing. This flexibility in preparation reduces the
need for kettles and steam tables since there is no need
for large amounts of food to be kept warm for long periods
of time.
In the Steam mode you can:
steam reheatreconstitute
stew thawsimmer
blanche preservebraise
poach
In the Hot Air mode you can:
roast bakegrill
gratinatebroil
In the Combination Steam and Hot Air mode you can:
Today the improvement of food quality is more important
than ever. Vegetables are cooked in the Blodgett CombiOven/Steamer without water at the optimal temperature
of just under 100ºC (21ºF), maintaining valuable vitamins, minerals, nutrients and trace elements. Cooking
meat in the Combi results in less shrinkage and a firmer,
juicier product. The Blodgett Combi-Oven/Steamer is being used more and more for baking. Steam and Hot Air
modes make it a general purpose baking appliance.
defrostroastrethermalize
reheat
bake
forced steam
NOTE: CNVX models only operate in hot air mode.
4
Installation
Description of the Combi-Oven/Steamer
ABOUT THE OVEN/STEAMER
OVEN/STEAMER OPERATION
Blodgett Combi-Oven/Steamers are quality produced using high-grade stainless steel with first class workmanship.
The practical oven door, with a viewing window, has a
wide swing radius and handle which can be operated easily, even with wet or greasy hands.
The multiple speed fan, which is guarded against accidental finger contact, is driven by a quiet and powerful
motor. The condenser draws out excess steam from the
appliance. Condensation and waste water, which result
during steaming and cleaning, are continuously drained.
Ease of operation is guaranteed through the simple arrangement of the controls. Graphic symbols make the appliance easy for even inexperienced kitchen staff to operate. The Steam On Demand feature allows the operator
to add steam at any time while operating in either the Hot
Air or Combi modes. This feature is excellent for baking
as well as roasting operations. A fourth function, the Cool
Down mode, allows the oven cavity to cool down rapidly
with the door opened.
The use of high quality insulation impedes excessive heat
radiation and saves energy.
The Oven/Steamer has optional adjustable legs which
adapt easily to slightly uneven surfaces and optional floor
stands which are designed for use with all of the table
models.
Cleaning is kept to a minimum. The interior is sprayed
with a self-acting cleaning solution which interacts with
steam to easily remove crusts and stains. The oven is
designed for easy care and is welded water tight so that
the internal cooking cavity may be rinsed with a hose after
the steam cleaning process.
The high performance fresh steam generator with its control system makes it possible to enjoy all of the advantages of a high quality steamer at the flick of a switch. Fresh
steam enters the oven cavity without pressure and is circulated at high speed. This process enables quick and
gentle cooking and ensures high quality food while providing convenient working methods. The steam generator
is completely automatic and protected from running dry.
5
Installation
Owner’s Responsibilities
Installation responsibilities prior to service startup inspection
You are entitled to a free start-up inspection service by
our factory ASAP. Before a factory representative arrives
to perform a startup procedure, the owner must already
have satisfied the following requirements.
NOTE: Please refer to Leg Attachment and Stacking.
Maximum shelf loading - 60 lbs (27.3 Kg)
1. Oven(s) are uncrated, stacked (if applies) and put in
place.
plumbing specifications
BCX-14G/AA, BCX-14E/AA
BX-14G/AA, and BX-14E/AA
WATER
Water pressure
Water connection
30 PSI (207 kPa) minimum
50 PSI (345 kPa) maximum
3/4” garden hose - Hot and Cold water
Water pressure regulator setting
Minimum requirements
Preset to 30 PSI (207 kPa)
TDS - less than 100 parts per million
Total Hardness - 80-120 parts per million
Chlorides - less than 30 parts per million
pH Factor - 7.0-8.0
Chlorine - 0 parts per million
DRAINAGE
Drain type
Drain connection
Average water drain temperature
Atmospheric Vented Drain
2.00” (50.8mm) Copper
Approximately 140ºF (60ºC)
2
CNVX-14G/AA
CNVX-14E/AA
3/4” garden hose for spray hose - Cold
water only
Installation
Owner’s Responsibilities
electrical ratings - GAS OVENS
BCX-14G/AA, BX-14G/AA and CNVX-14G/AA
gas input
voltage
Phase
amps
Type of gas
BCX-14G/AA
Natural
Steam - 50,000 BTU/Hr
Motor
120
1
20
1/2 HP 208-240VAC, 3 phase,
50/60 Hz
120
1
20
1/2 HP 208-240VAC, 3 phase,
50/60 Hz
Total - 113,000 BTU/Hr
BX-14G/AA and CNVX-14G/AA
Natural
Hot Air - 65,000 BTU/Hr
120
1
20
Propane
120
1
20
1/2 HP 208-240VAC, 3 phase,
50/60 Hz
1/2 HP 208-240VAC, 3 phase,
50/60 Hz
Hot Air - 65,000 BTU/Hr
Propane
Total - 115,000 BTU/Hr
Steam - 48,000 BTU/Hr
Hot Air - 65,000 BTU/Hr
Hot Air - 65,000 BTU/Hr
3/4” NPT connector for all U.S. and Canadian installations
voltage
hz
kW
208
240
480
60
60
60
19
19
19
RATINGS - ELECTRIC APPLIANCES
BCX-14E/AA, BX-14E/AA and CNVX-14E/AA
max load (amps
Phase
Motor
L1
L2
L2
3
53
53
50
1/2 HP 208-240VAC, 50/60 Hz
3
46
46
43
1/2 HP 208-240VAC, 50/60 Hz
3
23
23
21
1/2 HP 208-240VAC, 50/60 Hz
3
Installation
Utility Connections - Standards and Codes
THE INSTALLATION INSTRUCTIONS CONTAINED
HEREIN ARE FOR THE USE OF QUALIFIED INSTALLATION AND SERVICE PERSONNEL ONLY. INSTALLATION OR SERVICE BY OTHER THAN QUALIFIED
PERSONNEL MAY RESULT IN DAMAGE TO THE OVEN
AND/OR INJURY TO THE OPERATOR.
U.S. and Canadian Installations
Qualified installation personnel are individuals, a firm,
a corporation, or a company which either in person or
through a representative are engaged in, and are responsible for:
Reference: National Electrical Code, ANSI/NFPA 70-Latest Edition and/or Canadian Electrical Code CSA C22.1
as applicable.
•
The installation or replacement of gas piping. The
connection, installation, repair or servicing of equipment.
•
The installation of electrical wiring from the electric
meter, main control box or service outlet to the electric appliance.
Installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code,
NFPA54/ANSI Z223.1-Latest Edition, the Natural Gas Installation Code CAN/CGA-B149.1 or the Propane Installation Code, CAN/CGA-B149.2 as applicable.
This equipment is to be installed in compliance with the
Basic Plumbing Code of the Building Officials and Code
Administrators International Inc. (BOCA) and the Food
Service Sanitation Manual of the Food and Drug Administration (FDA).
Appliance is to be installed with backflow prevention in
accordance with applicable federal, province and local
codes.
Qualified installation personnel must be experienced in
such work, be familiar with all precautions required and
have complied with all requirements of state or local authorities having jurisdiction.
General Export Installations
Installation must conform with Local and National installation standards. Local installation codes and/or requirements may vary. If you have any questions regarding the
proper installation and/or operation of your appliance,
please contact your local distributor. If you do not have a
local distributor, please call Blodgett Combi at 0011-802658-6600.
4
Installation
Oven Location and Ventilation
OVEN LOCATION
ventilation
The well planned and proper placement of your oven will
result in long term operator convenience and satisfactory
performance.
The necessity for a properly designed and installed ventilation system cannot be over emphasized. The ventilation
system will allow the unit to function properly while removing unwanted vapors and products of combustion from
the operating area.
Certain minimum clearances must be maintained between the oven and any combustible or non-combustible
construction. See the table below.
The appliance must be vented with a properly designed
mechanically driven exhaust hood. The hood should be
sized to completely cover the equipment plus an overhang of at least 6” (15 cm) on all sides not adjacent to a
wall. The capacity of the hood should be sized appropriately and provisions made for adequate makeup air.
In addition, the following clearances are recommended
for servicing.
•
Oven body sides - 12” (30cm)
•
Oven body back - 12” (30cm)
NOTE: On gas models, routine servicing can usually
be accomplished within the limited movement
provided by the gas hose restraint. If the oven
needs to be moved further from the wall, the
gas must first be turned off and disconnected
from the oven before removing the restraint.
Reconnect the restraint after the oven has been
returned to its normal position.
WARNING!!
Failure to properly vent the oven can be hazardous to the health of the operator; and will
result in operational problems, unsatisfactory
baking, and possible damage to the equipment. Damage sustained as a direct result of
improper ventilation will not be covered by the
Manufacturer’s warranty.
Left Side Heat Shield
When installed in the Commonwealth of Massachusetts,
this appliance must be interlocked with the hood exhaust
system so that the appliance may be operated only when
the hood exhaust system is running.
Heat sources should not be near the air vents located on
the left hand side of the gas appliance.
Oven
Model
BCX-14G
CNVX-14G
BX-14G
BCX-14E
BX-14E
CNVX-14E
U.S. and Canadian Installations
MINIMUM REQUIRED
CLEARANCES
Right Side
Left Side
Back
1”
6”
6”
(25.4mm)
(152.4mm) (152.4mm)
1”
0”
6”
(25.4mm)
(0mm)
(152.4mm)
2”
2”
3”
(50.8mm)
(50.8mm)
(76.2mm)
Refer to your local ventilation codes. In the absence of
local codes, refer to the National ventilation code titled,
“Standard for the Installation of Equipment for the Removal of Smoke and Grease Laden Vapors from Commercial
Cooking Equipment”, NFPA-96- Latest Edition.
General Export Installations
Installation must conform with Local and National installation standards. Local installation codes and/or requirements may vary. If you have any questions regarding the
proper installation and/or operation of your unit, please
contact your local distributor. If you do not have a local
distributor, please call Blodgett Combi at 0011-802-6586600.
5
Installation
Leg Attachment
leg options
attachment
Legs are available in 4” (101mm), 6” (152mm) or 25”
(635mm) lengths or low profile casters.
•
The 4” (101mm) legs may be used when mounting
on a counter.
1. Align the threaded stud on one of the front legs to the
bolt hole located in the bottom corner of the
appliance. Turn the leg clockwise and tighten to the
nearest full turn.
•
The 6” (152.4mm) legs are used on the lower section of a double stacked appliance.
2. Align the leg plate holes with the bolt holes. Secure
with the two 1/2” bolts provided.
•
The 25” (635mm) legs are used for a single appliance located on the floor.
3. Repeat the above steps with the other front leg. If low
profile casters are used, install them with the locking
casters in the front of the oven. The rear casters do
not lock. Ensure that the locks are set on the front
casters.
NOTE: For safety reasons, casters must not be used
with the 25” (635mm) legs.
4. Tip the oven up on the newly installed front legs. If
casters are used, check that the locks are set on
the front casters. Repeat the above steps for the
rear legs.
5. Level the oven by screwing the adjustable feet in or
out as necessary.
25” (635mm) Adjustable Leg
6” (152,4mm) Adjustable Leg
4” (101mm) Leg
Low Profile Casters
Figure 1
Figure 2
6
Installation
Caster Attachment
1. Place a level on the floor where the casters are to
rest.
2. Place shims under the low side until it is level.
3. Mount the shims between the casters and the oven
as follows:
a. Align the shims and caster holes with the bolt
holes.
Add shims as necessary
b. Secure with the 1/2” bolts provided.
Floor
NOTE: Install them with the locking casters in the
front of the oven. The rear casters do not
lock. Ensure that the locks are set on the
front casters.
Exaggerated for clarity
Figure 3
4. Tip the oven up on the newly installed casters.
7
Installation
Stacking
1. Attach the legs or casters to the bottom oven.
WARNING!!
2. Place the top oven on the bottom oven. Be sure all
four sides are flush.
Stacking should be performed by qualified
installation personnel only. The ovens are
heavy. Take care to use proper tools and techniques when lifting and stacking units.
3. Remove left side oven panels.
4. Bolt the two ovens together from underneath into the
two threaded nut retainers.
5. GAS APPLIANCES ONLY: Attach the flue vents and
gas manifold as shown.
Hot Air Flue
Left Side of Ovens
with Side Panels
Removed
Threaded Nut Retainer
Bolt
Gas Manifold
Rear View BCX-14G
Figure 4
8
Steam Generator
Flue (BCX-14 only)
Installation
Deliming System Connection and Priming (BCX-14 units only)
Deliming System Connection
1. Push deliming tube onto barbed fitting on oven back.
NOTE: If needed use supplied hose retainers and self
drilling screws to route the deliming tube away
from hot exhaust ports.
Prime the deliming Pump
To prime the delime pump, use the following procedure for
your oven control.
Standard Control
1. Rotate the mode switch to COOL DOWN.
2. Press and hold both the Timer knob and the Steam on
Demand knob simultaneously. This will turn the pump
on.
Figure 5
3. Watch for deliming solution to flow through the tube.
Release the two knobs once the delime solution has
reached the barbed fitting on the back of the oven.
2. Cut deliming tube to length using the bottom of the
deliming fluid reservoir in its mounted position as a
guide. Install the jug weight on the deliming fluid reservoir end of the deliming tube.
4. Once the pump is primed, you may turn the mode
switch to any position.
MenuSelect™ Control
1. Press the Maintenance key.
2. Scroll to select MANAGER PROGRAM. Push the
knob.
NOTE: If the manager password is engaged, it will
need to be entered to proceed.
3. Scroll to PRIME DELIME PUMP and push the knob.
4. The display reads, PUSH KNOB TO PRIME. Hold the
knob to activate the pump.
Figure 6
5. Watch for deliming solution to flow through the tube.
Release the knob once the delime solution has
reached the barbed fitting on the back of the oven.
3. Insert the end of the deliming tube with the jug weight
into the deliming solution reservoir.
6. Once primed, press the ESC key three times to exit.
Figure 7
9
Installation
Plumbing Connections
Water Connection
Drain Connection
NOTE: Hot water maximizes steam production but is not
required. Cold water may be supplied to both
inlets if hot water is not available.
The drain should be run to an open floor drain avoiding
flexible hose that could sag and allow trapped water to
accumulate. The customer must supply the piping from
the oven to the drain.
Connect the appliance to quality water via a pressure
hose with 3/4” GHT (19mm) couplings. See below for
connections. A shut off valve is to be provided adjacent
to the oven.
Specific water/drain connection for City of Los Angeles
1. Each drain line from the appliance shall be routed
without dips or sags to terminate above the flood level
rim of an approved indirect waste receptor.
WARNING!!
Operating the appliance without the water regulator installed will invalidate your warranty.
2. The appliance shall be installed in accordance with
the manufacturer’s printed instructions and the LAPC
and LAMC, 1999 editions.
This product must be installed by a licensed Plumber or
Gas Fitter when installed within the Commonwealth of
Massachusetts.
3. A backflow protection device may be required by local codes. If so, install on the potable water system
directly ahead of the appliance. The backflow protection device shall be any of the following: an approved
pressure type vacuum breaker installed at least 12”
above the highest point of use, a double check valve
backflow preventer or a reduced pressure principal
backflow preventer.
Gas connection
BCX-14G and BX-14G
BCX-14E and BX-14E
Electrical connection
Filtered/boiler
connection
Unfiltered/condensate
and spray hose
connection
CNVX-14G
CNVX-14E
Figure 8
10
Installation
Electrical Connections
electrical connection
Electric Models
All Models
A strain relief for the power supply cord is provided. The
installer must supply a cord that meets all Local and National installation standards.
NOTE: Electrical connections must be performed by a
qualified installer only.
Before making any electrical connections to these appliances, check that the power supply is adequate for the
voltage, amperage, and phase requirements stated on
the rating name plate mounted on the appliance.
Gas Models
The circuit breaker that is used to provide power to this
appliance must have a minimum of .076” (3mm) contact
spacing. The circuit breaker must meet all Local and National installation standards.
This oven model uses a variable frequency inverter drive.
Appliances that use variable frequency inverter drives
produce high frequency noise and require filters and
shielded motor cabling. This causes higher leakage current toward Earth Ground. Especially, at the moment of
switching ON this can cause an inadvertent trip of the appliance’s ground fault interrupter (GFCI). Some GFCIs
are more sensitive than others. Blodgett has qualified
the Pass and Seymour brand, part number 2095, 20 A,
125 VAC, 60 Hz, specification grade GFCI duplex receptacle as being immune to the variable frequency inverter
drive’s noise. Blodgett recommends using this specific
GFCI for this model oven.
U.S. and Canadian Installations
A power cord (115V units only) is supplied with a plug attached. Plug the power cord into the desired receptacle.
All appliances must be installed in accordance with Local
or National Electrical codes.
A wiring schematic is located on the inside of the removeable side panel.
NOTE: Disconnect the power supply to the appliance
before servicing.
WARNING!!
Improper installation may invalidate your warranty.
WARNING!!
If the supply cord is damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.
11
Installation
Gas Connection
gas piping
Maximum Capacity of Iron Pipe in Cubic Feet of
Natural Gas Per Hour
A properly sized gas supply system is essential for maximum oven performance. Piping should be sized to provide a supply of gas sufficient to meet the maximum demand of all appliances on the line without loss of pressure
at the equipment.
(Pressure drop of 0.5 Inch W.C.)
Nominal Size, Inches
3/4”
1”
1-1/4” 1-1/2”
2”
10
360
680
1400 2100 3950
20
250
465
950
1460 2750
30
200
375
770
1180 2200
40
170
320
660
990
1900
50
151
285
580
900
1680
60
138
260
530
810
1520
70
125
240
490
750
1400
80
118
220
460
690
1300
90
110
205
430
650
1220
100
103
195
400
620
1150
From the National Fuel Gas Code Part 10 Table 10-2
Pipe
Length (ft)
Example:
NOTE: BTU values in the following example are for
natural gas.
You purchase a BCX-14G to add to your existing cook
line.
1. Add the BTU rating of your current appliances.
Pitco Fryer
120,000 BTU
6 Burner Range
60,000 BTU
Deck Oven
50,000 BTU
Total
230,000 BTU
2. Add the BTU rating of the new oven to the total.
Previous Total
230,000 BTU
BCX-14G
115,000 BTU
New Total
345,000 BTU
Maximum Capacity of Pipe in Thousands of
BTU/hr of Undiluted L.P. Gas at 11” W.C.
(Pressure drop of 0.5 Inch W.C.)
3. Measure the distance from the gas meter to the cook
line. This is the pipe length. Let’s say the pipe length
is 40’ (12.2 m) and the pipe size is 1” (2.54 cm).
Outside Diameter, Inches
3/4”
1”
1-1/2”
10
608
1146
3525
20
418
788
2423
30
336
632
1946
40
287
541
1665
50
255
480
1476
60
231
435
1337
70
215
404
1241
80
198
372
1144
90
187
351
1079
100
175
330
1014
From the National Fuel Gas Code Part 10 Table 10-15
Pipe
Length (ft)
4. Use the appropriate table to determine the total capacity of your current gas piping.
The total capacity for this example is 375,000 BTU. Since
the total required gas pressure, 345,000 BTU is less than
375,000 BTU, the current gas piping will not have to be
increased.
NOTE: The BTU capacities given in the tables are for
straight pipe lengths only. Any elbows or other
fittings will decrease pipe capacities. Contact
your local gas supplier if you have any questions.
12
Installation
Gas Connections
pressure regulation and testing
The gas pressure to the appliance must be rated for each
appliance while the burners are on. A sufficient gas pressure must be present at the inlet to satisfy these conditions. Refer to the table below for correct gas pressure.
Prior to connecting the appliance, gas lines should be
thoroughly purged of all metal filings, shavings, pipe
dope, and other debris. After connection, the appliance
must be checked for correct gas pressure.
Each appliance has been adjusted at the factory to operate with the type of gas specified on the rating plate.
U.S. and Canadian Installations
Installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code,
NFPA54/ANSI Z223.1-Latest Edition, the Natural Gas Installation Code CAN/CGA-B149.1 or the Propane Installation Code, CAN/CGA-B149.2 as applicable.
Each oven is supplied with a regulator to maintain the
proper gas pressure. The regulator is essential to the
proper operation of the oven and should not be removed.
DO NOT INSTALL AN ADDITIONAL REGULATOR
WHERE THE UNIT CONNECTS TO THE GAS SUPPLY
UNLESS THE INLET PRESSURE IS GREATER THAN
14” W.C. (1/2 PSI) (37mbar).
General Export Installations
Installation must conform with Local and National installation standards. Local installation codes and/or requirements may vary. If you have any questions regarding the
proper installation and/or operation of your appliance,
please contact your local distributor. If you do not have a
local distributor, please call Blodgett Combi at 0011-802658-6600.
The oven and its individual shutoff valve must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 1/2 psig (3.45kPa).
The oven must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during any pressure testing of the gas piping system at test
pressures equal or less than 1/2 psig (3.45kPa).
Gas Type
Inlet Pressure
BCX-14G
Natural
7-14” W.C.
Propane
12-14” W.C.
BX-14G and CNVX-14G
Natural
7-14” W.C.
Propane
12-14” W.C.
GAS PRESSURE
Orifice Size at Sea Level
Hot Air
Steam
Manifold Pressure
Hot Air
Steam
.0531” dia
.032” dia
.042” dia
.026” dia
3.5” W.C.
10” W.C.
3.5” W.C.
10” W.C.
.0531” dia
.032” dia
—
—
3.5” W.C.
10” W.C.
—
—
13
Installation
Gas Hose Restraint
U.S. and Canadian installations
If the appliance is mounted on casters, a commercial flexible connector with a minimum of 3/4” (1.9 cm) inside diameter must be used along with a quick connect device.
The connector must comply with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or
Connectors For Moveable Gas Appliances CAN/CGA6.16 and a quick disconnect device that complies with the
Standard for Quick-Disconnect Devices for Use With Gas
Fuel, ANSI Z21.41 or Quick Disconnect For Use With Gas
Fuel CAN 1-6.9. Adequate means must be provided to
limit the movement of the appliance without depending
on the connection and the quick disconnect device or its
associated piping.
A restraint must be used to limit the movement of the appliance so that no strain is placed upon the flexible connector. The restraint should be fastened to the base frame
of the oven as close to the flexible connector as possible.
It should be short enough to prevent any strain on the
connector. With the restraint fully stretched the connector
should be easy to install and quick connect.
The restraint (ie: heavy gauge cable) should be attached
without damaging the building. DO NOT use the gas piping or electrical conduit for the attachment of the permanent end of the restraint! Use anchor bolts in concrete or
cement block. On wooden walls, drive hi test wood lag
screws into the studs of the wall.
A drip leg must be used at each appliance. Refer to
NFPA54/ANSI Z223.1 - Latest Edition (National Fuel Gas
Code) for proper drip leg installation.
General export installations
Installation must conform with Local and National installation standards. Local installation codes and/or requirements may vary. If you have any questions regarding the
proper installation and/or operation of your appliance,
please contact your local distributor. If you do not have a
local distributor, please call Blodgett Combi at 0011-802658-6600.
WARNING!!
If the restraint is disconnected for any reason
it must be reconnected when the appliance is
returned to its original position.
Attachment Plate
(secure with leg mount bolt)
Quick Connect
Gas Hose
Gas Supply Line
IMPORTANT: Cable restraint
should be fastened as close
as possible to the flexible
connector and short enough
to prevent any strain on the
flexible connector.
Restraint
Installation of Gas Hose and Restraint
(Single Section Shown)
Figure 9
14
At maximum stretch of shortened restraint, the flexible
connector should be easy to
install and quick to connect.
Installation
Adjustments
DOOR ADJUSTMENT
Before applying power to the appliance for the first time,
check for the following conditions:
•
The door catch may be adjusted in and out using the following procedure:
All electrical safety provisions have been adhered
to and the electrical connections are correct.
1. Flip the rubber boot on the catch towards you.
•
Water is connected, turned on and all of the connections are water tight.
•
The pan holders are inserted into the oven cavity.
3. Rotate the catch clockwise or counter clockwise to
get proper adjustment.
•
Cardboard has been removed from oven cavity.
4. Retighten locknut, assuring the catch is vertical.
•
Gas has been turned on, if gas unit.
5. Flip the rubber boot back into position.
2. Loosen the locknut to make adjustment.
The hinges can also be adjusted as follows:
1. Loosen the two 1/4-20 bolts on the top of the hinge
plate and the two bolts on the bottom hinge plate.
2. Apply pressure to the door on the corners to get the
proper seal. While pushing, tighten the bolts in place.
Figure 10
15
Installation
Final Check Lists
Combi Mode - BCX-14 and BX-14 only
WARNING!!
Turn to COMBI mode, set thermostat to 350ºF (177ºC)
and verify:
Final check list must be performed by a qualified installer only.
•
Heat demand lamp is on.
ELECTRICAL CONTROL COMPARTMENT
•
Oven is heating.
•
•
Heat demand lamp shuts off at 350ºF (177ºC) and
oven maintains 350ºF (177ºC).
•
Fan shuts off with door open.
Voltage to appliance matches rating plate
PLUMBING FINAL CHECK
•
Incoming water pressure within appliance specification.
•
Atmospheric vented drain in place.
•
Water feed lines intact without leaks.
•
Ensure proper clearance as detailed.
•
Delime system has been primed. BCX-14 only.
Hot Air Mode - All models
Turn to HOT AIR mode and set thermostat to 400ºF
(204ºC) and verify:
oven operational tests
NOTE: Checks to be made by customer or authorized
service agent.
Heat demand lamp is on.
•
Oven is heating.
•
Heat demand lamp shuts off at 400ºF (204ºC) and
oven maintains 400ºF (204ºC).
•
Fan shuts off with door open.
Steam On Demand Mode - BCX-14 and BX-14 only
Cool Down Mode
•
•
Turn the oven to Hot Air mode. Set Steam On Demand for
1 minute. Press the Steam On Demand knob and verify:
Check that the fan runs with the door open.
Steam Mode - BCX-14 and BX-14 only
•
Steam demand lamp is on.
Turn on STEAM mode and set thermostat to steam. Verify
the following:
•
Steam demand lamp shuts off after approximately 1
minute.
•
Heat demand lamp is on.
Lights
•
Heat demand lamp shuts off at approximately 212ºF
(100ºC).
•
•
Set timer for 1 minute by rotating the knob. Be sure
the buzzer sounds when the time expires.
•
•
Run light (power light) turns on.
Fan Speed
•
Unit produces steam, window fogs, door seal does
not leak.
•
Press switch to ensure lights come on.
Cavity Vent
16
Press switch to ensure that the vent opens and
closes.
Press switch to ensure all fan speeds work.
Operation
Safety Information for Gas Units
What to do in the event of a power failure:
The information contained in this section is provided for
the use of qualified operating personnel. Qualified operating personnel are those who have carefully read the information contained in this manual, are familiar with the
functions of the oven and/or have had previous experience with the operation of the equipment described. Adherence to the procedures recommended herein will assure the achievement of optimum performance and long,
trouble-free service.
•
Turn all switches to off.
•
DO NOT attempt to operate the appliance until the
power is restored.
NOTE: In the event of a shut-down of any kind, allow a
five (5) minute shut off period before attempting
to restart the oven.
General safety tips:
Please take the time to read the following safety and operating instructions. They are the key to the successful
operation of your Blodgett oven.
SAFETY TIPS
For your safety read before operating
•
DO NOT use tools to turn off the gas control. If the
gas cannot be turned off manually do not try to repair it. Call a qualified service technician.
•
If the oven needs to be moved for any reason,
the gas must be turned off and disconnected from
the appliance before removing the restraint cable.
Reconnect the restraint after the oven has been
returned to its original location.
•
DO NOT remove the control panel cover unless the
oven is unplugged.
What to do if you smell gas:
•
What to do if you smell gas:
•
DO NOT try to light any appliance.
•
DO NOT touch any electrical switches.
•
Use an exterior phone to call your gas supplier immediately.
•
If you cannot reach your gas supplier, call the fire
department.
17
Operation
Power Switches
controls identification
1. HEAT CONTROL SWITCH
Gas Ovens - Used to turn gas on or off.
Electric Ovens - Used to turn power to the elements on or off.
2. CIRCUIT BREAKER - Used to turn power to the unit on or off. This switch should always stay ON.
Circuit
Breaker
See View A
Heat Shutoff
View A
Figure 11
18
Operation
Standard Controls for Models BCX-14 and BX-14
CONTROLS IDENTIFICATION
1. MODE SELECTOR SWITCH - turns power to the
oven on or off. Allows selection of Steam, Hot Air,
Combi or Cool Down Modes.
2. DISPLAY - displays time and temperature information.
3. TEMPERATURE DIAL - used to set desired cooking
temperature.
4. HEAT LAMP - lights when the oven is calling for heat
5. TIMER LED - lights when the cook time is displayed
6. PROBE ACTUAL LED - lights when the actual probe
temperature is displayed
7. PROBE SETPOINT LED - lights when the core setpoint temperature is displayed
8. TIMER/PROBE KNOB - use to select and set either
cook time or probe temperature
9. STEAM ON DEMAND DISPLAY - displays the steam
on demand time
10. STEAM ON DEMAND LAMP - lights when steam on
demand is activated.
11. STEAM ON DEMAND KNOB - use to set duration for
steam on demand
12. LIGHTS KEY - press to turn the oven lights on and off
13. FAN SPEED KEY - used to select fan speed.
14. CAVITY VENT KEY - used to open or close vent to
release steam from cavity. The vent is open when the
LED is lit.
15. DELIME LAMP (BCX-14 ovens only) - Flashes when
steam generator deliming is needed. Remains steady
when deliming process is active.
16. FILL LAMP - illuminated until the steam generator is
filled with water.
NOTE: Model BX-14 ovens do not have a fill lamp.
17. PROBE CONNECTION - used to connect the core
temperature probe to the control.
Figure 12
19
Operation
Standard Controls for Models BCX-14 and BX-14
TIMER COOKING
cool down
1. Press the TIMER/PROBE KNOB (8) to select the timer mode. The TIMER LED lights.
NOTE: The unit can be cooled down rapidly for steaming, cleaning, etc.
2. Turn the MODE SELECTOR Switch (1) to the desired
function.
1. To cool down the oven cavity, open the door and select Cool Down on the MODE SELECTOR Switch (1).
3. Set the TEMPERATURE DIAL (3) to the desired cook
temperature.
Steam on Demand
How to set the Steam On Demand feature:
For Steam mode, set the temperature no higher than
212ºF (100ºC).
For poaching, turn the temperature dial to the POACH
position, 180ºF (82ºC).
While in the Hot Air or Combi mode, the unit can be set
to steam for a timed period. At the end of the timed cycle
the unit reverts back to the original setting. Steam On Demand can be used at any time during the cook cycle.
The optimum temperature for Combi mode is 300350ºF (149-177ºC).
NOTE: Steam On Demand is not available in steam
mode.
4. When the oven has reached the cook temperature,
load the product.
1. Turn the STEAM ON DEMAND KNOB (11) to set the
desired length of time. The time is displayed in the
STEAM ON DEMAND DISPLAY (9).
5. Rotate knob to enter the desired cook time in the
display. You can clear the display by rotating counter
clockwise. The timer begins on its own.
2. Press the STEAM ON DEMAND KNOB (11). The
STEAM ON DEMAND LAMP (10) lights.
Uses for Steam On Demand:
6. The temperature, time and mode can be altered at
any time during the cooking process.
Most of the ideas came from our creative customers. Experiment with this feature on your own and let us know of
any new uses.
7. When the timer reaches 00:00, the buzzer sounds.
Press or rotate the TIMER/PROBE KNOB (8) counter
clockwise to silence the buzzer. Remove the product.
•
Add a minute or two at the beginning when baking
bread for a shiny crust.
•
Kick start large loads such as 20 or more chickens.
By starting large loads with 5 to 8 minutes of steam
you help the oven recover and cut the cooking time
by more than 10%.
2. Rotate the knob to enter the desired final cook temperature in the display.
•
3. Insert the core probe into the product. Load product
into the oven and close the door. Be sure that the
terminal end of the core probe is outside of the oven
and clear of the door.
Bake bagels without boiling. By starting raw bagels
with 1 to 2 minutes of steam you can achieve a
beautiful crust.
•
Cream caramel is great at 230ºF to 250ºF in the
Combi mode using 2 minutes of on demand steam.
•
When cooking chicken wings, try setting the oven
in the Combi mode at 375ºF and use 3 minutes of
Steam On Demand. This method will stop the tips
from burning. Total cooking time is approximately 12
minutes.
•
Pork ribs tend to pull off the bone better when using
5 to 8 minutes of Steam On Demand. Try ribs in the
Combi mode at 350ºF.
probe cooking
1. Press the TIMER/PROBE knob (8) to select the
probe setpoint mode. The PROBE SETPOINT LED
(7) lights.
4. Connect the core probe to the PROBE CONNECTION (17) at the bottom of the control.
5. The display gives the actual core probe temperature
by pressing the TIMER/PROBE knob (8) again.
6. When the product reaches the final cook temperature
the buzzer sounds.
20
Operation
MenuSelect™ Control for Models BCX-14 and BX-14
Control Description
1. START/STOP KEY - press to start, cancel or pause
the bake
2. COOL DOWN KEY - initiates oven cool down cycle
3. BAKE MORE KEY - press at the end of a bake cycle
to add additional bake time in one minute increments.
4. DISPLAY - displays time or temperature and other
information related to oven function and/or programming.
5. DIAL - used to enter set points, time, and programmable settings. Also used to select the programmed
product.
6. TEMP KEY - used to set or change the bake temperature
7. TIME KEY - used to set or change the bake time.
8. COMBI KEY - press to enter combi mode
9. STEAM KEY - press to enter steam mode
10. HOT AIR KEY - press to enter hot air mode
11. RETHERM KEY - press to enter retherm mode, this
mode uses steam to reheat frozen or precooked product. Retherm has a temperature limit of 250-300ºF.
12. STEAM ON DEMAND KEY - used to initiate steam
injection cycle
13. PROBE KEY - press to use core probe cooking
14. FAN KEY - press to select the fan speed
15. LIGHT KEY - press to turn the lights on and off.
16. VENT KEY - press to manually open and close the
oven vent
17. PROGRAM KEY - press to enter product programming and save programmed settings.
18. ESCAPE KEY - press to back up one step during programming
19. MAINTENANCE KEY - press to enter manager programming and save programmed settings
20. ALPHA/NUMERIC KEYPAD - used to program recipes.
21. POWER KEY - used to place control in and out of
standby mode.
Figure 13
21
Operation
MenuSelect™ Control for Models BCX-14 and BX-14
22. CORE PROBE CONNECTION - plug core temperature probe in here when using probe cooking
5. When the display flashes READY / IDLE, open the
doors. Load the product.
23. USB Port and COVER - Use to transfer recipes and
data to/from the control
6. Press the START/STOP KEY (1) to begin the bake
cycle. The timer counts down and the display alternates between the cooking mode and the name of
the product.
24. BUZZER - The buzzer is turned on/off through the
oven control.
PROGRAMMED COOKING
OVEN STARTUP
1. Turn the DIAL (1) until the name of the product is
highlighted. Press the center of the dial to select. The
oven preheats to the programmed temperature in the
correct cooking mode. The display flashes READY /
IDLE and the alarm beeps 5 times when the oven is
at temperature and ready to bake.
1. Be sure the gas shutoff switch and/or circuit breaker
switch below the control panel are in the on position.
The display flashes OFF PRESS POWER KEY TO
START.
NOTE: If the real time clock and auto wake up functions are enabled the display reads PRESS
POWER KEY TO START AUTO START.
2. Open the doors. Load the product.
2. Press the POWER KEY (21). The display reads
PREHEAT and the oven heats to the last manual set
temperature in the hot air mode. The display flashes
READY / IDLE and the alarm beeps 5 times when the
oven is at temperature and ready to bake.
3. Press the START/STOP KEY (1) to begin the bake
cycle. The timer counts down and the display alternates between the cooking mode and the name of
the product.
MANUAL COOKING
1. Press the PROBE key (13) to select the probe mode.
The display reads CORE PROBE COOK & HOLD.
Turn the dial to select either YES or NO. Press the
center of the dial to select.
PROBE COOKING
1. Turn the DIAL (5) until the display reads MANUAL.
2. Press the TIME KEY (7). Rotate the dial, or use the
alpha/numeric keypad to enter the desired bake time.
Press the center of the dial to set the bake time.
If YES is selected, Cook & Hold has been enabled.
In the Cook & Hold mode, the oven cavity lowers to
the product pull temperature as the product cooks.
NOTE: Time is set in one minute increments using
the dial. To set time in less than one minute
increments use the alpha/numeric keypad.
If NO is selected, Cook & Hold has not been enabled
the cavity maintains the cook temperature.
3. Press the TEMP KEY (6). Rotate the dial, or use the
alpha/numeric keypad to enter the desired bake temperature. Press the center of the dial to set the bake
temperature. The oven preheats to the new temperature.
2. Turn the DIAL to enter the desired product pull temperature in the display. Press the center of the dial to
save the pull temperature.
3. Press the TEMP KEY (6). Rotate the dial, or use the
alpha/numeric keypad to enter the desired bake temperature. Press the center of the dial to set the bake
temperature. The oven preheats to the new temperature.
NOTE: Temperature is set in 5 degree increments
using the dial. To set time in less than 5
degree increments use the alpha/numeric
keypad.
NOTE: Temperature is set in 5 degree increments
using the dial. To set time in less than 5
degree increments use the alpha/numeric
keypad.
4. Press the desired mode key, combi, steam, hot air or
retherm.
If Combi or Retherm are selected, rotate the dial, or
use the alpha/numeric keypad to enter the desired
percentage of steam.
NOTE: Retherm has a temperature limit of 250300ºF.
22
Operation
MenuSelect™ Control for Models BCX-14 and BX-14
4. Press the desired mode key, combi, steam, hot air or
retherm.
3. The Steam on Demand LED flashes until the steam
time has expired.
Venting Moisture from the Oven Cavity
If Combi or Retherm are selected, rotate the dial, or
use the alpha/numeric keypad to enter the desired
percentage of steam.
1. Press the VENT KEY (16). This manually opens the
vent until the key is pressed again to close it.
NOTE: Retherm has a temperature limit of 250300ºF.
Pause a Bake Cycle
5. Insert the core probe into the product. Load product
into the oven and close the door. Be sure that the
terminal end of the core probe is outside of the oven
and clear of the door.
1. To pause a cook cycle, press the START/STOP KEY
(1). The LED on the start/stop key flashes. The bake
cycle will pause until the key is pressed again.
6. Connect the core probe to the PROBE CONNECTION (22) at the bottom of the control.
1. To cancel the cook cycle, press and hold the START/
STOP KEY (1).
Cancel a Cook Cycle
At the End of Any COOK Cycle
NOTE: Do not connected the probe before the cook
mode has been selected.
1. An alarm sounds, the display reads DONE.
7. The display gives the actual core probe temperature
as well as the oven set temperature.
2. If more bake time is desired, press the BAKE MORE
KEY (3). This will add an additional one minute of
time for each press of the key.
8. When the product reaches the pull temperature the
buzzer sounds.
3. When you are satisfied with the bake, press the
START/STOP KEY (1) to silence the alarm. Open the
door to remove the product.
9. Press the START/STOP KEY (1) to silence the buzzer.
Oven Shutdown
If using Cook & Hold - The cavity temperature continues to drop to the product pull temperature and the
display counts up, telling the operator long the product has been held. Disconnect the core probe and
remove the product when ready.
1. Press the COOL DOWN KEY (2). The display reads
AUTO COOL DOWN ACTUAL TEMP. To speed up
the cool down process, open the doors and press the
VENT KEY (16) to open the vent.
If not using Cook & Hold - The cavity remains at
the cook temperature. The display does not count up.
Disconnect the core probe and remove the product
when the buzzer sounds.
2. When the oven has cooled down, the display reads
OFF PRESS POWER KEY TO START.
NOTE: The lights shut off and the vent closes automatically at the end of the cool down cycle.
During Any COOK Cycle
Steam On Demand
While in the Hot Air, Combi or retherm modes, the unit can
be set to steam for a timed period of up to 20 minutes.
At the end of the timed cycle the unit reverts back to the
original setting. Steam On Demand can be used at any
time during the cook cycle.
1. Press the STEAM ON DEMAND KEY (12).
2. Rotate the dial, or use the alpha/numeric keypad to
enter the desired steam on demand time. Press the
center of the dial to initiate Steam on Demand cycle.
NOTE: Steam on Demand time is set in one minute
increments using the dial. To set time in less
than one minute increments use the alpha/
numeric keypad.
23
Operation
MenuSelect™ Control for Models BCX-14 and BX-14
PRODUCT programming
4. Rotate the dial to select the desired cooking mode.
Choose from combi, steam, hot air or retherm. Press
the center of the dial to set the cook mode.
Entering the Program Mode
1. Press the PROGRAM KEY (17). If the control is password protected, the display reads ENTER CODE.
Use the alpha/numeric keypad to enter the manager
passcode 3124, then press the center of the dial to
enter the program mode.
If Combi or Retherm are selected, rotate the dial, or
use the alpha/numeric keypad to enter the desired
percentage of steam.
5. Rotate the dial, or use the alpha/numeric keypad to
enter the desired cook temperature. Press the center
of the dial to set the bake temperature.
Naming a Product Recipe
NOTE: Use the following procedure to name a new
product or edit the name of an existing product.
NOTE: Temperature is set in 5 degree increments
using the dial. To set time in less than 5
degree increments use the alpha/numeric
keypad.
1. For a new recipe, turn the dial to the first open product. Press the center of the dial to select.
To edit an existing name, rotate the dial to the name
to be changed. Press the center of the dial to select.
NOTE: Retherm has a temperature limit of 250300ºF.
2. Use the dial to scroll down to Edit Name. Press the
center of the dial to enter the edit name menu.
6. Rotate the dial to select the desired fan sprrd.
7. Rotate the dial to select the fan rotation cycle. Choose
between manual or auto.
3. Turn the dial or use the alpha/numeric keypad to select the first character. Press the center of the dial to
advance to the next character. Repeat for all remaining characters.
NOTE: This is the length of time the fan will rotate
in one direction before reversing.
If manual is selected, rotate the dial or use the alpha/
numeric keypad to enter the desired fan cycle. Press
the dial to set the fan cycle.
NOTE: Product names may be up to 10 characters
long and can contain spaces. Use the #1
key to insert spaces in a recipe name.
If auto is selected, the program will use the default
fan cycle setting. The default is set through the Manager Programming.
NOTE: To select letters using the keypad, press the
appropriate key once if you need the first
letter on the key, twice for the second and
three times for the third. For example to enter the letter L press the #5 key three times.
8. Rotate the dial to set the vent position. Choose between OPEN or CLOSE. Press the center of the dial
to set the vent position.
4. Press the PROG KEY (17). With SAVE highlighted,
press the dial to save the product name.
9. Use the dial to scroll down to PRODUCT NAME:
STAGE 2. Press the center of the dial to select stage
2.
Programming a Product Recipe
NOTE: The control can hold 99 recipes. Each recipe
may have up to 6 cooking stages.
10. Repeat steps 2-9 for all remaining stages.
1. Turn the dial to highlight the name of the product to
be programmed. Press the center of the dial to select
the product.
11. When all stages have been programmed, press the
PROGRAM KEY (17). To save the programming, use
the dial to scroll to YES. Press the center of the dial.
The control exits the program mode.
2. The display reads PRODUCT NAME: STAGE 1.
Press the center of the dial to select the stage.
3. Rotate the dial, or use the alpha/numeric keypad to
enter the desired bake time. Press the center of the
dial to set the bake time.
NOTE: Time is set in one minute increments using
the dial. To set time in less than one minute
increments use the alpha/numeric keypad.
24
Operation
MenuSelect™ Control for Models BCX-14 and BX-14
Using the USB Port
Programming Oven Setup
1. With the power on, remove the cover of the USB port
(23) and insert the USB drive.
These menus allow the manager to set up basic oven
functions
2. Press the MAINTENANCE KEY (19).
1. Turn the dial to highlight OVEN SETUP. Press the
center of the dial to select.
3. Turn the dial to highlight MANAGER PROGRAM.
Press the center of the dial to select.
2. Turn the dial to highlight MANAGER PROGRAM.
Press the center of the dial to select.
4. Turn the dial to highlight either COPY RECIPE FROM
USB or COPY RECIPE TO USB, then press the center of the dial to select.
3. Turn the dial to highlight the oven function you with to
change. Press the center of the dial to select. Choose
from the following functions:
5. When the transfer is complete, press any key to return to the menu.
Recipe Password - Select YES or NO to enable
password protection on recipe programming. If YES
is selected the passcode 3124 must be entered to
change recipe programming.
6. Turn the dial to highlight EXIT. Press the center of
the dial to select. The display returns to the previous
menu.
Temp Unit - Select either degrees F or C.
7. Turn the dial to highlight EXIT. Press the center of the
dial to select.
Cool Down Temp - Select the set temperature for
the oven to achieve in Cool Down mode
MANAGER programming
Temp Disp Rate - Set the rate, in seconds, at which
the display switches between actual and setpoint
temperature
Entering the Manager Program Mode
Input Rsp Time - Set the length of time allowed to input each variable when programming recipes before
control automatically exits out
1. Press the MAINTENANCE KEY (19). If the control
is password protected, the display reads ENTER
CODE. Use the alpha/numeric keypad to enter the
manager passcode 3124, then press the center of the
dial to enter the program mode.
Setback Time - When not used for a period of time,
the oven temperature will automatically reduce to
conserve energy. This variable sets the length of time
the oven remains at the idle temperature before being lowered.
2. Turn the dial to highlight OVEN SETUP. Press the
center of the dial to select the product.
Programming Auto Start
Ready Beep - Select either ON or OFF. This is the audible alarm that sounds when the oven has reached
the set temperature.
NOTE: The Auto Start function enables the oven to turn
on at a programmed time of day and preheat to
a programmed temperature.
Cook Done Beep - Select either ON or OFF. This is
the audible alarm that sounds when the product cook
time has expired.
1. Turn the dial to highlight AUTO START. Press the
center of the dial to select.
Cook Cool Fan - Select either YES or NO. This function allows the control to display OPEN OVEN DOOR
when you are attempting to lower the set temperature
of the oven.
2. Turn the dial to select either ON or OFF. Press the
center of the dial to select.
If ON is selected, the display reads AUTO START 24
HOUR TIME 00:00. Turn the dial to enter the time you
would like the oven to begin preheating. Press the
center of the dial to select.
Restore Manual SE - Select either YES or NO. This
variable enables the oven to remember the last settings used for manual cooking.
The display reads AUTO START TEMP XXX. Turn
the dial to enter the desired preheat temperature.
Press the center of the dial to select.
NOTE: The following apply to BCX models only.
Boiler Set Temp Preheat - Select the temperature in
the boiler when it is in stand by
Boiler Set Temp Cook - Select the temperature in
the boiler when steam is being produced
25
Operation
MenuSelect™ Control for Models BCX-14 and BX-14
Delime Fill Time - Set the length of time the boiler
continues to fill with deliming solution beyond the
standard water level in order to ensure all of the scale
present in the boiler is removed.
Delime Interval - Set the length of time between deliming intervals
Delime Time - Set the time during the day when the
display alerts the user to delime
Flush Interval - Set the length of time between boiler
flushes
Flush Time - Set the time during the day when the
display alerts the user to flush the boiler
4. After editing a function, press the center of the dial
to save.
5. When all desired functions have been edited, turn the
dial to highlight EXIT. Press the center of the dial to
exit the manager programming mode.
26
Operation
Standard Controls for Models CNVX-14
CONTROLS IDENTIFICATION
1. MODE SELECTOR SWITCH - turns power to the
oven on or off. Allows selection of Hot or Cool Down
Modes.
2. TEMPERATURE DIAL - used to set desired cooking
temperature.
3. DISPLAY - displays time and temperature information.
4. HEAT LAMP - lights when the oven is calling for heat
5. PROBE ACTUAL LED - lights when the actual probe
temperature is displayed
6. PROBE SETPOINT LED - lights when the core setpoint temperature is displayed
7. TIMER/PROBE KNOB - use to select and set either
cook time or probe temperature
8. LIGHTS KEY - press to turn the oven lights on and off
9. FAN SPEED KEY - used to select fan speed.
10. CAVITY VENT KEY - used to open or close vent to
release steam from cavity.
11. PROBE CONNECTION - used to connect the core
temperature probe to the control.
Figure 14
27
Operation
Standard Controls for Models CNVX-14
TIMER COOKING
probe cooking
1. Press the TIMER/PROBE KNOB (7) to select the timer mode. The TIMER LED lights.
1. Press the TIMER/PROBE knob (7) to select the
probe setpoint mode. The PROBE SETPOINT LED
(6) lights.
2. Turn the MODE SELECTOR Switch (1) to the desired
function.
2. Rotate the knob to enter the desired final cook temperature in the display.
3. Set the TEMPERATURE DIAL (2) to the desired cook
temperature.
3. Insert the core probe into the product. Load product
into the oven and close the door. Be sure that the
terminal end of the core probe is outside of the oven
and clear of the door.
4. When the oven has reached the cook temperature,
load the product.
5. Rotate knob to enter the desired cook time in the
display. You can clear the display by rotating counter
clockwise. The timer begins on its own.
4. Connect the core probe to the PROBE CONNECTION (11) at the bottom of the control.
5. The display gives the actual core probe temperature
by pressing the TIMER/PROBE knob (7) again.
6. The temperature and time can be altered at any time
during the cooking process.
6. When the product reaches the final cook temperature
the buzzer sounds.
7. When the timer reaches 00:00, the buzzer sounds.
Press or rotate the TIMER/PROBE KNOB (2) counter
clockwise to silence the buzzer. Remove the product.
cool down
NOTE: The unit can be cooled down rapidly for cleaning, etc.
1. To cool down the oven cavity, open the door and select Cool Down on the MODE SELECTOR Switch (1).
28
Operation
MenuSelect™ Control for Model CNVX-14
CONTROLS IDENTIFICATION
1. START/STOP KEY - press to start, cancel or pause
the bake
2. COOL DOWN KEY - initiates oven cool down cycle
3. BAKE MORE KEY - press at the end of a bake cycle
to add additional bake time in one minute increments.
4. DISPLAY - displays time or temperature and other
information related to oven function and/or programming.
5. DIAL - used to enter set points, time, and programmable settings. Also used to select the programmed
product.
COOKIES
FRENCH FRY
ROAST CHIX
6. TEMP KEY - used to set or change the bake temperature
7. TIME KEY - used to set or change the bake time.
8. FAN KEY - press to select fan speed.
9. LIGHT KEY - press to turn the oven interior lights on
or off
10. VENT KEY - press to manually open and close the
oven vent
11. PROGRAM KEY - press to enter product programming and save programmed settings
12. ESCAPE KEY - press to back up one step during programming
13. MAINTENANCE KEY - press to enter manager programming and save programmed settings
14. ALPHA/NUMERIC KEYPAD - used to program recipes.
15. POWER KEY - used to place control in and out of
standby mode.
16. PROBE KEY - press to use core probe cooking
17. PROBE CONNECTION - used to connect the core
temperature probe to the control.
18. USB Port and COVER - Use to transfer recipes and
data to/from the control
19. BUZZER - The buzzer is turned on/off through the
oven control.
Figure 15
29
Operation
MenuSelect™ Control for Model CNVX-14
operation
PROGRAMMED COOKING
1. Turn the DIAL (5) until the name of the product is
highlighted. Press the center of the dial to select. The
oven preheats to the programmed temperature in the
correct cooking mode. The display flashes READY /
IDLE and the alarm beeps 5 times when the oven is
at temperature and ready to bake.
OVEN STARTUP
1. Be sure the gas shutoff switch and/or circuit breaker
switch below the control panel are in the on position.
The display flashes OFF PRESS POWER KEY TO
START.
NOTE: If the real time clock and auto wake up functions are enabled the display reads PRESS
POWER KEY TO START AUTO START.
2. Open the doors. Load the product.
3. Press the START/STOP KEY (1) to begin the bake
cycle. The timer counts down and the display alternates between the cooking mode and the name of
the product.
2. Press the POWER KEY (15). The display reads
PREHEAT and the oven heats to the last manual set
temperature in the hot air mode. The display flashes
READY / IDLE and the alarm beeps 5 times when the
oven is at temperature and ready to bake.
PROBE COOKING
1. Press the PROBE key (16) to select the probe mode.
The display reads CORE PROBE COOK & HOLD.
Turn the dial to select either YES or NO. Press the
center of the dial to select.
MANUAL COOKING
1. Turn the DIAL (5) until the display reads MANUAL.
2. Press the TIME KEY (7). Rotate the dial, or use the
alpha/numeric keypad to enter the desired bake time.
Press the center of the dial to set the bake time.
If YES is selected, Cook & Hold has been enabled.
In the Cook & Hold mode, the oven cavity lowers to
the product pull temperature as the product cooks.
NOTE: Time is set in one minute increments using
the dial. To set time in less than one minute
increments use the alpha/numeric keypad.
If NO is selected, Cook & Hold has not been enabled
the cavity maintains the cook temperature.
2. Turn the DIAL to enter the desired product pull temperature in the display. Press the center of the dial to
save the pull temperature.
3. Press the TEMP KEY (6). Rotate the dial, or use the
alpha/numeric keypad to enter the desired bake temperature. Press the center of the dial to set the bake
temperature. The oven preheats to the new temperature.
3. Press the TEMP KEY (6). Rotate the dial, or use the
alpha/numeric keypad to enter the desired bake temperature. Press the center of the dial to set the bake
temperature. The oven preheats to the new temperature.
NOTE: Temperature is set in 5 degree increments
using the dial. To set time in less than 5
degree increments use the alpha/numeric
keypad.
NOTE: Temperature is set in 5 degree increments
using the dial. To set time in less than 5
degree increments use the alpha/numeric
keypad.
4. When the display flashes READY / IDLE, open the
doors. Load the product.
5. Press the START/STOP KEY (1) to begin the bake
cycle. The timer counts down and the display alternates between the cooking mode and the name of
the product.
4. Insert the core probe into the product. Load product
into the oven and close the door. Be sure that the
terminal end of the core probe is outside of the oven
and clear of the door.
5. Connect the core probe to the PROBE CONNECTION (17) at the bottom of the control.
NOTE: Do not connected the probe before the cook
mode has been selected.
6. The display gives the actual core probe temperature
as well as the oven set temperature.
30
Operation
MenuSelect™ Control for Model CNVX-14
7. When the product reaches the pull temperature the
buzzer sounds.
PRODUCT programming
8. Press the START/STOP KEY (1) to silence the buzzer.
1. Press the PROGRAM KEY (11). If the control is password protected, the display reads ENTER CODE.
Use the alpha/numeric keypad to enter the manager
passcode 3124, then press the center of the dial to
enter the program mode.
Entering the Program Mode
If using Cook & Hold - The cavity temperature continues to drop to the product pull temperature and the
display counts up, telling the operator long the product has been held. Disconnect the core probe and
remove the product when ready.
Naming a Product Recipe
NOTE: Use the following procedure to name a new
product or edit the name of an existing product.
If not using Cook & Hold - The cavity remains at
the cook temperature. The display does not count up.
Disconnect the core probe and remove the product
when the buzzer sounds.
1. For a new recipe, turn the dial to the first open product. Press the center of the dial to select.
To edit an existing name, rotate the dial to the name
to be changed. Press the center of the dial to select.
During Any COOK Cycle
Venting Moisture from the Oven Cavity
2. Use the dial to scroll down to Edit Name. Press the
center of the dial to enter the edit name menu.
1. Press the VENT KEY (10). This manually opens the
vent until the key is pressed again to close it.
3. Turn the dial or use the alpha/numeric keypad to select the first character. Press the center of the dial to
advance to the next character. Repeat for all remaining characters.
Pause a Bake Cycle
1. To pause a cook cycle, press the START/STOP KEY
(1). The LED on the start/stop key flashes. The bake
cycle will pause until the key is pressed again.
NOTE: Product names may be up to 10 characters
long and can contain spaces. Use the #1
key to insert spaces in a recipe name.
Cancel a Cook Cycle
1. To cancel the cook cycle, press and hold the START/
STOP KEY (1).
NOTE: To select letters using the keypad, press the
appropriate key once if you need the first
letter on the key, twice for the second and
three times for the third. For example to enter the letter L press the #5 key three times.
At the End of Any COOK Cycle
1. An alarm sounds, the display reads DONE.
2. If more bake time is desired, press the BAKE MORE
KEY (3). This will add an additional one minute of
time for each press of the key.
4. Press the PROG KEY (11). With SAVE highlighted,
press the dial to save the product name.
3. When you are satisfied with the bake, press the
START/STOP KEY (1) to silence the alarm. Open the
door to remove the product.
Oven Shutdown
1. Press the COOL DOWN KEY (2). The display reads
AUTO COOL DOWN ACTUAL TEMP. To speed up
the cool down process, open the doors and press the
VENT KEY (10) to open the vent.
2. When the oven has cooled down, the display reads
OFF PRESS POWER KEY TO START.
NOTE: The lights shut off and the vent closes automatically at the end of the cool down cycle.
31
Operation
MenuSelect™ Control for Model CNVX-14
Programming a Product Recipe
the dial to scroll to YES. Press the center of the dial.
The control exits the program mode.
NOTE: The control can hold 99 recipes. Each recipe
may have up to 6 cooking stages.
1. Turn the dial to highlight the name of the product to
be programmed. Press the center of the dial to select
the product.
Using the USB Port
2. The display reads PRODUCT NAME: STAGE 1.
Press the center of the dial to select the stage.
2. Press the MAINTENANCE KEY (13).
1. With the power on, remove the cover of the USB port
(18) and insert the USB drive.
3. Turn the dial to highlight MANAGER PROGRAM.
Press the center of the dial to select.
3. Rotate the dial, or use the alpha/numeric keypad to
enter the desired bake time. Press the center of the
dial to set the bake time.
4. Turn the dial to highlight either COPY RECIPE FROM
USB or COPY RECIPE TO USB, then press the center of the dial to select.
NOTE: Time is set in one minute increments using
the dial. To set time in less than one minute
increments use the alpha/numeric keypad.
5. When the transfer is complete, press any key to return to the menu.
4. Rotate the dial, or use the alpha/numeric keypad to
enter the desired cook temperature. Press the center
of the dial to set the bake temperature.
6. Turn the dial to highlight EXIT. Press the center of
the dial to select. The display returns to the previous
menu.
NOTE: Temperature is set in 5 degree increments
using the dial. To set time in less than 5
degree increments use the alpha/numeric
keypad.
7. Turn the dial to highlight EXIT. Press the center of the
dial to select.
MANAGER programming
NOTE: Retherm has a temperature limit of 250300ºF.
Entering the Manager Program Mode
5. Rotate the dial to select the desired fan speed.
Choose from gentle, low, high or turbo. Press the
center of the dial to set the fan speed.
1. Press the MAINTENANCE KEY (13). If the control
is password protected, the display reads ENTER
CODE. Use the alpha/numeric keypad to enter the
manager passcode 3124, then press the center of the
dial to enter the program mode.
6. Rotate the dial to select the fan rotation cycle. Choose
between manual or auto.
2. Turn the dial to highlight OVEN SETUP. Press the
center of the dial to select the product.
NOTE: This is the length of time the fan will rotate
in one direction before reversing.
Programming Auto Start
If manual is selected, rotate the dial or use the alpha/
numeric keypad to enter the desired fan cycle. Press
the dial to set the fan cycle.
NOTE: The Auto Start function enables the oven to turn
on at a programmed time of day and preheat to
a programmed temperature.
If auto is selected, the program will use the default
fan cycle setting. The default is set through the Manager Programming.
1. Turn the dial to highlight AUTO START. Press the
center of the dial to select.
7. Rotate the dial to set the vent position. Choose between OPEN or CLOSE. Press the center of the dial
to set the vent position.
2. Turn the dial to select either ON or OFF. Press the
center of the dial to select.
If ON is selected, the display reads AUTO START 24
HOUR TIME 00:00. Turn the dial to enter the time you
would like the oven to begin preheating. Press the
center of the dial to select.
8. Use the dial to scroll down to PRODUCT NAME:
STAGE 2. Press the center of the dial to select stage
2.
9. Repeat steps 2-9 for all remaining stages.
The display reads AUTO START TEMP XXX. Turn
the dial to enter the desired preheat temperature.
Press the center of the dial to select.
10. When all stages have been programmed, press the
PROGRAM KEY (11). To save the programming, use
32
Operation
MenuSelect™ Control for Model CNVX-14
Programming Oven Setup
4. After editing a function, press the center of the dial
to save.
These menus allow the manager to set up basic oven
functions
5. When all desired functions have been edited, turn the
dial to highlight EXIT. Press the center of the dial to
exit the manager programming mode.
1. Turn the dial to highlight OVEN SETUP. Press the
center of the dial to select.
2. Turn the dial to highlight MANAGER PROGRAM.
Press the center of the dial to select.
3. Turn the dial to highlight the oven function you with to
change. Press the center of the dial to select. Choose
from the following functions:
Recipe Password - Select YES or NO to enable
password protection on recipe programming. If YES
is selected the passcode 3124 must be entered to
change recipe programming.
Temp Unit - Select either degrees F or C.
Cool Down Temp - Select the set temperature for
the oven to achieve in Cool Down mode
Temp Disp Rate - Set the rate, in seconds, at which
the display switches between actual and setpoint
temperature
Input Rsp Time - Set the length of time allowed to input each variable when programming recipes before
control automatically exits out
Setback Time - When not used for a period of time,
the oven temperature will automatically reduce to
conserve energy. This variable sets the length of time
the oven remains at the idle temperature before being lowered.
Ready Beep - Select either ON or OFF. This is the audible alarm that sounds when the oven has reached
the set temperature.
Cook Done Beep - Select either ON or OFF. This is
the audible alarm that sounds when the product cook
time has expired.
Cook Cool Fan - Select either YES or NO. This function allows the control to display OPEN OVEN DOOR
when you are attempting to lower the set temperature
of the oven.
Restore Manual SE - Select either YES or NO. This
variable enables the oven to remember the last settings used for manual cooking.
33
Operation
SmartTouch Touchscreen Control for Model BX-14
Control Description
1. DISPLAY - displays information related to oven function and/or programming.
BX-14
2. CORE PROBE CONNECTION - plug core temperature probe in here when using probe cooking
3. USB Port and COVER - Use to transfer recipes and
data to/from the control
1
4. HEAT CUTOFF - used to turn gas on or off (HV-100G
only)
5. CIRCUIT BREAKER - Used to turn power to the unit
on or off.
2
5
3
HEAT CUTOFF CIRCUIT BREAKER
4
Figure 16
34
Operation
SmartTouch Touchscreen Control for Model BX-14
manual mode cooking
1. Select the POWER button to turn on the oven and
proceed to the manual screen.
Figure 17
35
Operation
SmartTouch Touchscreen Control for Model BX-14
ity. Press SAVE & EXIT to return to the manual cook
screen. The steam on demand timer will start and the
icon will flash blue while active. To stop the timer, hit
the icon and press CLEAR then SAVE & EXIT.
2. Set the desired cook settings.
Temperature - Press the temperature text and enter
the desired oven temperature on the keypad provided. Press SAVE & EXIT key to return to this screen.
Fan Speed - With the FAN icon highlighted, press the
fan speed text (Gentle, Low, High or Turbo). When
Turbo is displayed, press the text again to reduce the
fans speed to Gentle.
Cook Time - Press the time text and enter the desired cook time on the keypad provided. Press SAVE
& EXIT to return to this screen.
Core Probe Cooking - To use the core probe cooking feature, press the PROBE COOK icon. Press the
temperature text that appears and enter the desired
product core temperature on the keypad provided.
Press SAVE & EXIT key to return to the manual cook
screen. Insert a product probe in the probe outlet on
the control panel. To use the HOLD option, press the
HOLD key. Once activated, key will be blue. To escape from probe cooking press the time icon.
Fan Reversal Interval - To adjust the fan reversal
time, press the FAN REVERSAL icon. Then press
the time text and enter the desired reversal interval
on the keypad provided. Press SAVE & EXIT key to
return to this screen.
Vent Position - At any time the vent can be opened
or closed by toggling the VENT icon. When the icon
is highlighted the vent is open.
Lights - At any time the lights can be turned on or off
by toggling the LIGHT icon.
Modes - Press the HOT AIR icon to run in Hot Air
mode. The hot air icon highlights in red when active.
The Steam icon highlights in blue when active. Press
the Combi icon and enter the desired humidity percentage on the keypad provided. Press SAVE & EXIT
to return to the manual cook screen
3. Press START Icon to begin cooking. Press Cancel
key to stop cooking. Press +1 MIN to add 1 minute to
the cook time.
Steam on Demand - Press the Steam On Demand
key and enter the desired time period of 100% humid-
Temperature
Probe Cooking
Time
Combi Mode
Steam on Demand
Hot Air Mode
Steam Mode
Fan Reversal Increment
Fan Speed
Vent Position
Lights
36
Operation
SmartTouch Touchscreen Control for Model BX-14
Menu mode cooking
1. On a manual screen, press the ESC key to exit the
the screen.
4. Select the desired food category for your product.
2. Select the MENU icon to cook using the pre programmed menu items.
Figure 20
5. Within the food category, select the desired product
you wish to cook.
Figure 18
3. Push the SELECT ITEM key in the top right corner of
the screen.
Figure 21
6. Once selected the control returns to the Menu Cooking screen. Press the START KEY to begin the cook
cycle.
Figure 19
37
Operation
SmartTouch Touchscreen Control for Model BX-14
shelf cooking
1. Select the SHELF COOKING key.
3. During the cook cycle, individual shelf cook timers will
count down as the product is cooked. If you wish to
cancel the bake, you can press the STOP ALL key, or
you can stop individual shelves.
To add time, select +1 MIN key for individual shelves
or +1 MIN ALL key to add time to all shelves. Each
time the key is pressed, 1 minute of cook time is added.
Press STOP again to reset to the original values.
CLEAR ALL to clear all products from all shelves. All
Shelves must be cleared to escape the screen.
Once the bake is complete the beeper will sound.
Figure 22
2. Select which shelves you intend to place the selected
food item on. Press selected item icon in the upper
right corner of the screen to add different items that
share the same cook temperature but may have different cook times.
Once preheated, start icons will appear. You can
choose start all or start individual shelves.
Figure 24
Figure 23
38
Operation
SmartTouch Touchscreen Control for Model BX-14
editing a menu
1. Select the MENU/EDIT icon to edit the recipes in the
menu mode.
3. To edit an existing item, select the item while the EDIT
ITEMS key is highlighted.
To delete an Item, select the item while the DELETE
key is highlighted.
To create a new item, select the NEW ? icon while the
EDIT key is highlighted.
Figure 25
2. Select the EDIT ITEMS icon to edit the menu items.
Figure 27
Figure 26
39
Operation
SmartTouch Touchscreen Control for Model BX-14
4. Each recipe is made up of steps containing seven
settings - temperature, time, fan, etc. A new step is
needed when you desire a different setting within a
step.
To edit a setting within a particular step, press the
icon for that setting. A keypad will appear for you to
input your value.
To add a step, press the + key icon.
To edit a step, press the arrow keys on the bottom left
hand corner of the screen to highlight the step you
wish to edit. Follow the instructions above to edit the
settings.
To delete a step, use the arrow keys on the bottom
left hand corner of the screen to highlight the step
you wish to delete. Press the red X icon to delete the
highlighted step.
Once you are finished, press the DISK icon to save
the changes.
Figure 28
40
Operation
SmartTouch Touchscreen Control for Model BX-14
editing a category
1. Select the MENU/EDIT icon to edit the recipes in the
menu mode.
To delete a category, select the category while the
DELETE key is highlighted.
To create a new category, select the NEW ? icon
while the EDIT key is highlighted.
Figure 29
Figure 31
2. Select the EDIT CATEGORIES icon to select which
items are in each category.
4. Select what you would like to edit.
To edit the name, press the EDIT NAME key. A keyboard will appear, enter the desired name and press
ENTER to return to this menu.
Figure 30
3. To edit an existing category, select the category while
the EDIT key is highlighted.
Figure 32
41
Operation
SmartTouch Touchscreen Control for Model BX-14
5. To edit the category icon, press the category icon displayed in the category edit screen. The Select Icon
screen is displayed. Select the desired icon. To view
more icon options, press the arrow key.
6. To edit items within a category, press the SELECT
ITEMS key on the edit category screen.
Select the items you would like to appear within the
category. When complete, press ESC key to return
to the previous menu. Press the DISK icon to save
your changes.
Once the category icon is selected, the category edit
screen is displayed. Press the DISK icon to save your
changes.
Figure 34
Figure 33
42
Operation
SmartTouch Touchscreen Control for Model BX-14
creating new menu items
5. Program the recipe steps - Each recipe is made
up of steps containing seven settings - temperature,
time, fan, etc. A new step is needed when you desire
a different setting within a step.
1. Select the EDIT ITEMS key.
To edit a setting within a particular step, press the
icon for that setting. A keypad will appear for you to
input your value.
To add a step, press the + key icon.
To edit a step, press the arrow keys on the bottom left
hand corner of the screen to highlight the step you
wish to edit. Follow the instructions above to edit the
settings.
To delete a step, use the arrow keys on the bottom
left hand corner of the screen to highlight the step
you wish to delete. Press the red X icon to delete the
highlighted step.
Once you are finished, press the DISK icon to save
the changes.
6. To file recipe under an existing category, press the
EDIT CATEGORIES key. Select the desired category. Press the SELECT ITEMS key. Highlight the new
item. Press the ESC key. The disk will be displayed,
press to save your changes.
Figure 35
2. Select New?
3. Select the food icon to be displayed. Use the arrow keys to page through the available icons. Press
the desired icon to select and return to the previous
screen.
4. Name the item. Press the blank shelf below the icon
to name the recipe. A keyboard will appear. Enter the
desired name. Press ENTER when finished to return
to the previous screen.
43
Operation
SmartTouch Touchscreen Control for Model BX-14
creating new categories
1. Select the EDIT CATEGORIES key.
4. Press EDIT NAME. A keyboard will appear. Enter the
desired name. Press ENTER when finished to return
to the previous screen.
5. Press SELECT ITEMS. Select items to be filed in the
new category. Items will be highlighted as they are
selected. Press ESC key to return to the previous
screen. The disk will be displayed, press to save your
changes.
6. To display the category, it must be added to the default menu as follows:
Press the EDIT MENUS key. Select the DEFAULT
key. Select the CATEGORIES key. Highlight the new
category. Press the ESC key to return to the previous
screen. The disk will be displayed, press to save your
changes.
Figure 36
2. Select New?
3. Select the category icon to be displayed. Use the arrow keys to page through the available icons. Press
the desired icon to select and return to the previous
screen.
44
Operation
SmartTouch Touchscreen Control for Model BX-14
transferring recipes using the usb
To Store Menu Data to a USB
1. Return to the power screen.
1. Press the STORE MENU DATA to USB key to transfer recipes to the USB.
Figure 37
Figure 39
2. Press the TOOLS key. Enter the code 6647 on the
keypad.
2. The keyboard screen is displayed. Use to enter desired file name. Press the ENTER key when finished.
Figure 38
Figure 40
3. Press the MANAGE MENU DATA key. Insert the USB
drive into the Intelliport.
45
Operation
SmartTouch Touchscreen Control for Model BX-14
3. The status screen appears to display the download
status. The display returns to the previous screen
when download is complete.
Figure 43
Figure 41
3. The overwrite warning screen appears. Press YES to
continue
4. Press the ESC key to exit USB screen.
To Retrieve Menu Data from USB
1. Press the GET MENU DATA from USB key to transfer
recipes from the USB.
Figure 44
4. The status screen appears to display the upload status. The display returns to the previous screen when
upload is complete.
Figure 42
5. Press the ESC key to exit USB screen.
2. The control displays all menu (.MNU) files on the USB
drive. Select the desired file.
46
Operation
SmartTouch Touchscreen Control for Model BX-14
cool down
1. To cool down the unit, press the COOL DOWN icon.
2. The oven will toggle between cooling and open door
in yellow until the oven is cool. Once cool, the oven
will go to standby.
NOTE: If the oven is shut down with the circuit
breaker switch at the bottom of the front
panel, the display will return to the power
screen. Select your option to begin.
Figure 45
Figure 46
47
Maintenance
Spray Bottle Operating Procedure
3. To spray, depress the trigger with your thumb.
NOTE: Only use a commercial oven cleaner/degreaser
with the spray bottle. DO NOT use chemicals
that are not intended as oven cleaners. See
chemical manufacturer’s information for intended
use.
1. Unscrew the sprayer head and fill the container to
the MAX mark. Screw the head assembly on firmly
to ensure an airtight seal. The liquid must be clean
and free from foreign matter. Do not overfill - space
must be left for compressing air.
Figure 49
4. Adjust spray nozzle for a wide spray pattern.
5. After a period of spraying, the pressure will drop. Restore the pressure by operating the air pump.
Figure 47
6. Release pressure after use by inverting the spray
head and depressing the trigger or by slowly unscrewing the spray head assembly which will allow
air to escape from around the filling aperture.
2. To build up pressure, pump approximately 20 full
strokes when the container is filled with liquid. The
higher the pressure, the finer the spray. If the container is only partially filled, then more pumping is required to compress the additional air space.
7. After use, rinse the spray bottle with clean water and
check that the hole in the nozzle is perfectly clean
and clear. Warm water (not hot) used with a household detergent is a useful cleaning agent for this purpose.
NOTE: Further information can be found in the
instruction leaflet supplied with your spray
bottle.
WARNING!!
Protective clothing and eyewear should be
worn while using cleaning and deliming
agents.
To order additional bottles or spray heads use the following part numbers:
Complete Spray Bottle - P/N R0006
Spray Head Repair Kit - P/N R6332
Figure 48
48
Maintenance
Cleaning and Preventive Maintenance
Daily Cleaning
Cleaning the Interior
6. Leave the door open overnight to vent the oven. If the
oven will not be used for an extended period of time,
place the oven in hot air mode to dry.
Daily cleaning of the oven is essential for sanitation, and
to ensure against operational difficulties. The stainless
steel cavity may corrode with improper cleaning of the
oven. Use an oven cleaning detergent in conjunction with
the supplied spray bottle.
For difficult cleaning, allow the spray-on oven cleaner to
work longer before rinsing.
1. Open the oven door. Place the oven in cool down
mode. Let the oven cool to below 140ºF (60ºC).
2. Fill the spray bottle with a mild oven detergent. DO
NOT use abrasive cleaners on your Blodgett
Combi. Be sure to follow the MSDS or safety instructions on the bottle of your oven cleaner. We
recommend the following cleaners:
Greasecutter Plus by Ecolab
EZ Clean by Cellow
Figure 51
Advance Oven Cleaner by Diversey-Lever
Cleaning the Exterior
3. Pump the bottle twenty times to build up pressure.
The higher the pressure, the finer the spray. Spray
the oven interior. Turn the nozzle to adjust the spray
pattern.
The exterior of the appliance may be cleaned and kept in
good condition with a light oil. Saturate a cloth and wipe
the appliance when it is cold; wipe dry with a clean cloth.
4. Close the door. Place the oven in steam mode for 10
minutes.
WARNING!!
DO NOT spray the outside of the oven with
water or clean with a water jet. Cleaning with
a water jet can impregnate chlorides into the
stainless steel, causing the onset of corrosion.
5. When finished steaming, open the door and rinse the
interior with the attached spray hose.
Clean the air intake / cooling fan behind the oven so that
it is free of all lint, grease or other inhibitors of air flow.
Keeping this area free of obstruction will extend the life of
the components.
Preventive Maintenance
The best preventive maintenance measures are the
proper initial installation of the equipment and a program
for cleaning the appliance routinely. The Oven/Steamer
requires no lubrication. Contact the factory, the factory
representative or a local Blodgett Combi service company to perform maintenance and repairs should they be
required.
Figure 50
49
Maintenance
Cleaning and Preventive Maintenance
BX-14 Boilerless Oven Weekly Cleaning
In addition to the daily cleaning, it is necessary to clean
behind the fan guard of this oven on a weekly basis. This
is necessary for proper functioning of the oven. Scale will
build up on the fan and heat source leading to a less efficient oven.
5. Fill the spray bottle as described in the Daily Cleaning procedure. Thoroughly spray cleaner onto the fan,
heat source and back of the fan guard. Resecure the
fan guard.
1. Open the oven door. Place the oven in cool down
mode. Let the oven cool to below 140ºF (60ºC).
2. Once cool, turn the oven off.
3. Remove the oven racks and the rack guides on the
left side.
Figure 54
6. Close the door. Place the oven in the steam mode for
approximately 10 minutes.
7. After ten minutes, swing the fan guard towards the
front of the oven. Use plenty of water to rinse all of
the cleaner off.
Figure 52
4. Rotate the two screws on the left side of the fan guard.
Swing the fan guard toward the front of the oven.
Figure 55
8. Return the fan guard to the closed position. Rotate
the two screws to secure the fan guard.
Figure 53
9. Reintall the rack guides and oven racks.
10. Leave the oven door open overnight to vent the oven.
If the oven will not be used for an extended period of
time, place the oven in hot air mode to dry the interior
cavity.
50
Maintenance
Flushing the Boiler - BCX Models Only
Standard Control
Menuselect™ control
A flush of the boiler is required every 24 hours and happens either automatically or can be initiated at any time.
A flush of the boiler is required every 24 hours and happens either automatically or can be initiated at any time.
NOTE: In order to flush the oven, the water and gas
supply must be left on.
NOTE: In order to flush the oven, the water and gas
supply must be left on.
•
If the mode switch is in the OFF position and a flush
is required, the flush will automatically run.
•
•
If the boiler is too hot to drain, the flush will begin
when the boiler water temperature drops below
140ºF (60ºC).
If the oven is off (the display reads “OFF - PRESS
POWER KEY TO START”) and a flush is required,
the flush will automatically run.
•
If the boiler is too hot to drain, the flush will begin
when the boiler water temperature drops below
140ºF (60ºC).
To manually initiate a flush sequence
To manually initiate a flush sequence
1. If the oven is hot, place it in the Cool Down mode with
the door open until the cavity is below 140ºF (60ºC).
1. If the oven is hot, place it in the Cool Down mode with
the door open until the cavity is below 100ºF (38ºC).
2. Close the door, turn the mode switch to the Cool
Down position. Push and hold the timer knob until the
flush begins.
2. Close the door, press the MAINT key, turn the knob
until “FLUSH” is highlighted. Push the knob to select.
3. Scroll to “START FLUSH”. Push the knob to select.
NOTE: If the boiler water temperature is too high,
the flush will start automatically when the
water temperature drops below 140ºF
(60ºC).
4. The display reads “FLUSH PROGRAMMING - START
FLUSH - NO”. Rotate the knob until the display reads
“FLUSH PROGRAMMING - START FLUSH - YES”.
Push the knob to select.
3. The flush completes in about 25 minutes. When complete, the oven shuts off automatically.
5. The flush completes in about 25 minutes. When complete, the oven shuts off automatically.
To cancel a flush sequence
1. Push and hold the Steam on Demand knob. The display reads “FLUSH ABORT NO”.
To cancel a flush sequence
1. Press the ESC key. The display reads “NEXT FLUSH
TIME - HH:MM 24:00”. Rotate the knob or use the
keypad to enter the amount of time (HH:MM) desired
before the next automatic flush sequence.
2. Rotate the timer knob until the display reads “FLUSH
ABORT YES”. Push in the timer knob to cancel the
flush.
If the flush was required and tries to start again, push
and hold the timer knob until 24:00 appears in the
display. Rotate the knob to enter the amount of time
(HH:MM) desired before the next automatic flush sequence.
51
Maintenance
Deliming
BCX Combi Ovens
bcx with Standard Control
Deliming of the steam generator is the single most important preventative maintenance task. Lime will build up
inside the steam generator, reducing efficiency and causing damage to the boiler.
This control comes equipped with a delime lamp to indicate when the steam generator needs to be delimed.
The delime lamp will flash when the steam generator has
been run for the preset interval. This is a warning only,
the oven can be used all day before deliming. The delime
sequence can be run at anytime regardless of the flashing
delime indicator.
WARNING!!
Problems caused by insufficient deliming are
not covered by the warranty.
WARNING!!
Deliming solutions are hazardous and can
cause burns to the skin and eyes. Wear protective clothing and eyewear.
WARNING!!
Figure 57
DO NOT cook while deliming.
1. Be sure the container delivering the deliming agent to
the appliance is full. Be sure to follow the MSDS or
safety instructions on your deliming agent. Use a
non-diluted deliming agent.
NOTE: Once the deliming process has been started, the
oven cannot be used until deliming is complete,
approximately 45 minutes.
Deliming the Boiler with the Standard Control
1. If the oven is hot, place in the Cool Down mode with
the door open until the cavity is below 140ºF (60ºC).
2. With the mode switch in Cool Down, push and hold
the Steam on Demand knob until the delime lamp
flashes faster. Then release the knob. The display
reads “To start delime turn mode switch
to off”.
Figure 56
2. Ensure that the deliming pump has been primed. Refer to the Deliming System Connection & Priming if
you are uncertain.
Figure 58
3. Close the oven door. Turn the oven to the Off mode.
The display reads “DELIME STEP 1 OF 14”.
The remainder of the process is automatic. The delime lamp stays lit until deliming is completed.
52
Maintenance
Deliming
4. When the delime lamp goes out, the oven can be
used normally.
2. After the cool down the unit will automatically turn itself off. Close the door. Press the maintenance key.
To Cancel the Deliming Process
If a delime is required when the power key is pressed,
the display reads “DELIME REQUIRED START DELIMING YES”. In this case, skip to step 5.
1. To cancel the deliming process, push and hold the
Steam on Demand knob. The display reads “DELIME
ABORT NO”.
2. Rotate the timer knob until the display reads “DELIME
ABORT YES”. Push the timer knob.
If the delime process was not required or chemical
has not been pumped into the boiler yet, the delime
is immediately cancelled.
If chemical is in the boiler, the delime process will advance to step 9 of the process in order to flush the
chemical from the boiler.
bcx with Menuselect™ Control
When it is time to delime your BCX, the display reads
“DELIME REQUIRED START DELIME YES”. To postpone
the delime, turn the knob until the display reads “DELIME
REQUIRED START DELIME NO”. Push the knob.
Figure 60
3. Turn the dial to highlight “DELIME”. Press the center
of the dial to select.
DELIME REQUIRED
START
DELIME
YES
1. OVEN SETUP
2. SERVICE
3. DELIME
4. FLUSH
Figure 59
The message will return until the unit is delimed. This is a
warning only, the oven can be used all day before deliming. The delime sequence can be run at anytime.
Figure 61
NOTE: Once the deliming process has been started, the
oven cannot be used until deliming is complete,
approximately 45 minutes.
Deliming the Boiler with the MenuSelect™ Control
1. If the oven is hot, place in the Cool Down mode with
the door open until the cavity is below 140ºF (60ºC).
53
Maintenance
Deliming
4. Turn the dial to highlight “START DELIME”. Press the
center of the dial to select.
6. When the deliming process is complete, the control
will turn itself off. The oven can now be used normally.
1. START DELIME
2. DELIME INT 2 DY
3. NEXT DELIME
4. DELIME TIME
ENERGY SAFE MODE
SET TEMP XXXF
Figure 62
Figure 64
To Cancel the Deliming Process
5. Turn the dial to highlight YES, this confirms that you
want to begin the deliming process. Press the center
of the dial to select. The remainder of the process is
automatic. The display shows the step number and
progress by %.
1. To cancel the deliming process, push and hold the
ESC key. The display reads “DELIME ABORT? NO”.
2. Rotate the knob until the display reads “DELIME
ABORT? YES”. Press the knob to select.
3. The control returns to the Off mode.
DELIME PROGRAMMING
START
DELIME
YES
Figure 63
54
Maintenance
Deliming
BX-14 Boilerless Oven
It may be necessary to delime the oven interior and behind the fan guard. This is necessary for proper functioning of the oven. Lime will build up on the fan and heat
source leading to a less efficient oven.
6. Thoroughly spray deliming agent onto the fan, heat
source and back of fan guard. Wait 10 minutes.
1. Open the oven door. Place the oven in cool down
mode. Let the oven cool to below 140ºF (60ºC).
2. Fill the spray bottle with a non-diluted deliming agent.
Be sure to follow the MSDS or safety instructions
on your deliming agent.
3. Pump the bottle twenty times to build up pressure.
The higher the pressure, the finer the spray
4. Remove the oven racks and the rack guides on the
left side.
Figure 67
7. After ten minutes, use the spray hose and plenty of
water to rinse all of the deliming agent off. Repeat
steps 6 & 7 if necessary.
NOTE: If the lime scale is hard to remove or takes
multiple applications, your water filtration
system may be insufficient or your filters
may need to be changed.
Figure 65
5. Rotate the two screws on the left side of the fan guard.
Swing the fan guard toward the front of the oven.
Figure 68
8. Return the fan guard to the closed position. Rotate
the two screws to secure the fan guard.
9. Reintall the rack guides and oven racks.
10. Leave the oven door open overnight to vent the oven.
If the oven will not be used for an extended period of
time, place the oven in hot air mode to dry the interior
cavity.
Figure 66
55
Maintenance
Deliming
Deliming Interval Setting - BCX Only
Refer to figure below to determine the correct deliming interval for your appliance. Find your location and the corresponding
potentiometer setting. These values are general and are guidelines only. Your specific water quality may be harder or softer.
Adjust the deliming interval to your specific water quality.
NOTE: If you have the oven connected to a filter system, the water hardness may be reduced. Check with filter supplier
for details.
Over 14 gpg
Extremely Hard
Setting A
10 to 14 gpg
Very Hard
Setting B
Most of Canadian water contains 112
mg/L (8 gpg).
7 to 10 gpg
Hard
Setting B
Moderately Hard
Setting C
This would place Canada in the hard
water catagory and setting B should be
used. If your water exceeds 196 mg/L
(14 gpg), setting A should be used.
Slightly Hard
Setting C
3 to 7 gpg
Less than 3 gpg
Canadian Water Quality
Figure 69
56
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement