Casio 5288 Watch User Manual

MA1305-EB
Ú#!3)/#/-054%2#/,4$
Operation Guide 5288
ENGLISH
Congratulations upon your selection of this CASIO watch.
E-1
E-2
E-3
About This Manual
x Depending on the model of your watch, display text
appears either as dark figures on a light background, or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
x Button operations are indicated using the letters shown in
the illustration.
x Note that the product illustrations in this manual are
intended for reference only, and so the actual product may
appear somewhat different than depicted by an illustration.
Things to check before using the watch
1. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To configure Home City settings” (page E-14) to
configure your Home City and daylight saving time settings.
Important!
Proper World Time Mode data depend on correct Home City, time, and date
settings in the Timekeeping Mode. Make sure you configure these settings
correctly.
2. Set the current time.
x See “Adjusting the Digital Time and Date Settings” (page E-17).
The watch is now ready for use.
E-4
E-5
E-22
Contents
E-4
About This Manual
E-5
Things to check before using the watch
E-9
Mode Reference Guide
E-13 Timekeeping
E-14 Configuring Home City Settings
E-14 To configure Home City settings
E-16 To change the Daylight Saving Time (summer time) setting
E-17 Adjusting the Digital Time and Date Settings
E-17 To configure the digital time and date settings
E-21 Checking the Current Time in a Different Time Zone
E-21 To enter the World Time Mode
E-21 To view the time in another time zone
To specify standard time or daylight saving time (DST) for a city
E-23 Countdown Timer
E-23 To enter the Countdown Timer Mode
E-26 To configure the countdown timer
E-28 To perform a countdown timer operation
E-28 To stop the alarm
E-29 Using the Stopwatch
E-29 To enter the Stopwatch Mode
E-30 To perform an elapsed time operation
E-30 To pause at a split time
E-30 To measure two finishes
E-32 Using the Alarm
E-33 To enter the Alarm Mode
E-34 To set an alarm time
E-35 To test the alarm
E-6
E-7
E-35
E-35
To turn an alarm and the Hourly Time Signal on and off
To stop the alarm
E-36 Adjusting the Analog Hand Setting
E-36 To adjust the analog time
E-38 Illumination
E-38 To turn on illumination
E-39 To change the illumination duration
E-40 Troubleshooting
E-41 Specifications
E-8
Mode Reference Guide
Your watch has 6 “modes”. The mode you should select depends on what you
want to do.
To do this:
Enter this mode:
x View the current date in the Home City
x Configure Home City and daylight saving time (DST) Timekeeping Mode
settings
x Configure time and date settings
View the current time in one of 27 cities
World Time Mode
(29 time zones) around the globe
Use the countdown timer
Countdown Timer Mode
Use the stopwatch to measure elapsed time
Stopwatch Mode
Set an alarm time
Alarm Mode
Adjust the analog hands
Hand Setting Mode
See:
E-13
E-21
E-23
E-29
E-32
E-36
E-9
Operation Guide 5288
Selecting a Mode
x Press C to cycle between the modes as shown below.
x In any mode (except when a setting mode, with flashing digits is on the display),
press B to illuminate the display.
Timekeeping Mode
World Time Mode
C
Countdown Timer Mode
C
Stopwatch Mode
C
Alarm Mode
C
Hand Setting Mode
C
C
E-10
E-11
General Functions (All Modes)
The functions and operations described in this section can be used in all of the
modes.
Auto Return Features
x The watch returns to the Timekeeping Mode automatically if you do not perform
any button operation for two or three minutes in the Alarm Mode.
x If you leave a setting mode with flashing digits on the display for two or three
minutes without performing any operation, the watch exits the setting mode
automatically.
Timekeeping
Minutes
Hour
Use the Timekeeping Mode to set and view the current
time and date.
x Each press of D cycles the digital display contents as
shown below.
Day of the Week
Month-Day
D
Initial Screens
When you enter the World Time Mode or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
Hour : Minutes
D
Seconds
D
PM indicator
Scrolling
The B and D buttons are used on the setting mode to scroll through data on the
display. In most cases, holding down these buttons during a scroll operation scrolls
through the data at high speed.
D
Day of week
E-12
E-13
3. Press D (East) and B (West) to select the city code
you want to use as your Home City.
x Keep pressing D or B until the city code you want
to select as your Home City appears on the display.
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City, and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
1. In the Timekeeping Mode, hold down A for about two
seconds until the seconds start to flash. This is the
setting mode.
x The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
4. After the setting is the way you want, press A to
return to the Timekeeping Mode.
City Code
2. Press C twice to move the flashing to the city code.
x For details about city codes, see the “City Code
Table” at the back of this manual.
Seconds
Note
x After you specify a city code, the watch will use UTC*
offsets in the World Time Mode to calculate the current
time for other time zones based on the current time in
your Home City.
* Coordinated Universal Time, the world-wide scientific
standard of timekeeping.
The reference point for UTC is Greenwich, England.
E-14
E-15
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
DST indicator
seconds until the seconds start to flash. This is the
setting mode.
Adjusting the Digital Time and Date Settings
Use the procedure below to adjust the digital time and date settings.
3. Press D to toggle between Daylight Saving Time (On)
and Standard Time (OFF).
Note
x After adjusting the digital time and date setting, be sure to adjust the analog hands
so the settings match.
x See “Adjusting the Analog Hand Setting” (page E-36).
4. After the setting is the way you want, press A to
return to the Timekeeping Mode.
x The DST indicator appears to indicate that Daylight
Saving Time is turned on.
To configure the digital time and date settings
1. In the Timekeeping Mode, hold down A for about two
seconds until the seconds start to flash. This is the
setting mode.
2. Press C to display the DST setting mode.
Seconds
E-16
E-17
2. Press C to move the flashing in the sequence shown below to select the other
settings.
C
Seconds
C
DST
C
Home City Code
C
Hour
Minutes
C
C
Illumination Duration
C
Day
C
Month
C
Year
C
12/24-Hour Format
x The following steps explain how to configure timekeeping settings only.
3. When the timekeeping setting you want to change is flashing, use D and/or B
to change it as described below.
Screen
To do this:
Do this:
Reset the seconds to 00
Press D.
Toggle between Daylight Saving Time (ON)
and Standard Time (OFF)
Press D.
Change the city code
Use D (East) and B (West).
Change the hour or minute
Use D (+) and B (–).
Toggle between 12-hour (12H) and 24-hour
Press D.
(24H) timekeeping
Change the year, month, or day
Use D (+) and B (–).
4. Press A to exit the setting mode.
E-18
E-19
Operation Guide 5288
Note
x For information about selecting a Home City and configuring the DST setting, see
“Configuring Home City Settings” (page E-14).
x While 12-hour format is selected for timekeeping, a P (PM) indicator will appear
for times from noon to 11:59 p.m. No indicator appears for times from midnight to
11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without any
P (PM) indicator.
x The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
x The day of the week changes automatically when the date changes.
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current
time in one of 29 time zones (27 cities) around the
globe. The city that is currently selected in the World
Time Mode is called the “World Time City”.
Currently selected
World Time City
To enter the World Time Mode
Use C to select the World Time Mode as shown on
page E-10.
To view the time in another time zone
In the World Time Mode, use D (East) to scroll through
city codes.
Current time in the currently
selected World Time City
E-21
E-20
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use D (East) to display the
DST indicator
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
Countdown Timer
The countdown timer can be set within a range of
one minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
2. Hold down A for about two seconds.
x This toggles the city code you selected in step 1
between Daylight Saving Time (DST indicator
displayed) and standard time (DST indicator not
displayed).
x Using the World Time Mode to change the DST setting of the city code that is
selected as your Home City also will change the Timekeeping Mode time DST
setting.
x Note that you cannot switch between standard time/daylight saving time (DST)
while GMT is selected as the World Time City.
x The standard time/daylight saving time (DST) setting affects only the currently
selected time zone. Other time zones are not affected.
To enter the Countdown Timer Mode
Use C to select the Countdown Timer Mode as shown
on page E-10.
Minutes
Seconds
Configuring the Countdown Timer
The following are the settings you should configure
before actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
E-22
E-23
x See “To configure the countdown timer” on page E-26 for information about setting
up the timer.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is
repeated a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
x Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you
can press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes
the types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
x When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
x When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
x Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
x 30 seconds before the end of the countdown, the watch emits four short beeps.
x The watch emits a short beep for each of the last 10 seconds of the countdown.
x If the countdown start time is six minutes or greater, the watch emits a short beep
for each second of the final 10 seconds before the five-minute point is reached.
Four short beeps are emitted to signal when the five-minute point is reached.
E-24
E-25
To configure the countdown timer
1. While the countdown start time is on the display in
the Countdown Timer Mode, hold down A until the
current countdown start time starts to flash, which
indicates the setting mode.
x If the countdown start time is not displayed, use the
procedure under “To perform a countdown timer
operation” (page E-28) to display it.
2. Press C to move the flashing in the sequence shown below to select other
settings.
C
Start Time
Setting
Screen
Button Operation
Start Time
Use D (+) and B (–) to change the setting.
x You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Auto-repeat
Press D to toggle auto-repeat on (
displayed).
(
Progress Beeper
Press D to toggle the progress beeper on (
(
).
displayed) and off
) and off
4. Press A to exit the setting mode.
x You can also perform steps 1 and 2 of the above procedure whenever you need
to view the current auto-repeat and progress beeper settings.
C
Auto-repeat
3. When the setting you want to change is flashing, use B and D to change it as
described below.
Progress Beeper
C
E-26
E-27
To perform a countdown timer operation
Using the Stopwatch
D
D
D
D
A
Start
Stop
(Restart)
(Stop)
Reset
The stopwatch measures elapsed time, split times, and two finishes.
To enter the Stopwatch Mode
Use C to select the Stopwatch Mode as shown on page
E-11.
x Before starting a countdown timer operation, check to make sure that a
countdown operation is not in progress (indicated by the seconds counting down).
If it is, press D to stop it and then A to reset to the countdown start time.
To stop the alarm
Press any button.
Minutes
E-28
Seconds
E-29
Operation Guide 5288
To perform an elapsed time operation
D
D
D
D
A
Start
Stop
(Restart)
(Stop)
Reset
To pause at a split time
D
A
A
D
A
Start
Split
(SPL displayed)
Split release
Stop
Reset
D
A
A
Split release
Display time of
second runner.
Reset
Note
x The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59 seconds.
x Once started, stopwatch timing continues until you press D to stop it, even if
you exit the Stopwatch Mode to another mode and even if timing reaches the
stopwatch limit defined above.
x Exiting the Stopwatch Mode while a split time is frozen on the display clears the
split time and returns to elapsed time measurement.
To measure two finishes
D
A
Start
Split
Stop
(SPL displayed)
Second runner
First runner finishes. finishes.
Display time of first
runner.
E-30
E-31
Using the Alarm
Alarm number
You can set five independent daily alarms. When a
daily alarm is turned on, an alarm tone will sound
for about 20 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time.
This is true even if the watch is not in the Timekeeping
Mode. One of the alarms is a snooze alarm, while the
other four are one-time alarms. The snooze alarm
operation repeats every five minutes.
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
To enter the Alarm Mode
Use C to select the Alarm Mode as shown on page E-11.
x The snooze alarm screen is indicated by SNZ, while the other alarm screens are
numbered AL1 through AL4. The Hourly Time Signal screen is indicated by SIG.
x When you enter the Alarm Mode, the data you were viewing when you last exited
the mode appears first.
Alarm time (Hour : Minutes)
E-32
E-33
5. Press A to exit the setting mode.
To set an alarm time
Alarm ON/OFF indicator
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
D
AL1
D
AL2
D
AL3
D
AL4
D
SNZ
SIG
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select an alarm or the
Hourly time signal
Hourly Time Signal.
on indicator
2. When the alarm or the Hourly Time Signal you want is
selected, press A to toggle it between on and off.
x The alarm on indicator (when any alarm is on), snooze
alarm indicator (when the snooze alarm is on), and the
Hourly Time Signal on indicator (when the Hourly Time
Signal is on) are shown on the display in all modes.
D
2. Hold down A for about two seconds until the alarm time starts to flash. This is
the setting mode.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
x When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
Snooze alarm indicator
To stop the alarm
Press any button.
E-34
E-35
Adjusting the Analog Hand Setting
Use the following procedure to adjust the analog hands so their settings match the
digital time.
To adjust the analog time
1. Use C to select the Hand Setting Mode as shown on
page E-11.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting mode.
x If you need to advance the analog time setting a long way, hold down D until
the time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,
or countdown beeper) starts to sound.
4. Press A to exit the setting mode.
x The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting mode.
x To return to the Timekeeping Mode, press C.
3. Press D to advance the analog time setting by
20 seconds.
x Holding down D advances the analog time setting
at high speed.
E-36
E-37
Illumination
The face of the watch is illuminated for easy reading in
the dark.
To turn on illumination
In any mode (except when a setting mode, with flashing
digits is on the display), press B to illuminate the display.
x You can use the procedure below to select either
1.5 seconds or 3 seconds as the illumination duration.
When you press B, the display will remain illuminated
for about 1.5 seconds or 3 seconds, depending on the
current illumination duration setting.
E-38
To change the illumination duration
1. In the Timekeeping Mode, hold down A until the seconds start to flash. This is
the setting mode.
2. Press C nine times so the illumination duration setting mode is on the display.
3. Press D to toggle the illumination duration between 1.5 seconds ( ) and
3 seconds ( ).
4. After the settings are the way you want, press A to exit the setting mode.
Illumination Precautions
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
E-39
Operation Guide 5288
Troubleshooting
Specifications
Time Setting
■ The current time setting is off by hours.
Your Home City setting may be wrong (page E-14). Check your Home City setting
and correct it, if necessary.
Accuracy at normal temperature: ±30 seconds a month
Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to
2039
Other: 4 screen formats (Day of the Week, Month - Day, Hour : Minutes,
Seconds); Home City code (can be assigned one of 31 city codes);
Standard Time/Daylight Saving Time (summer time)
World Time: 27 cities (29 time zones)
Other: Daylight Saving Time/Standard Time
Stopwatch:
Measuring unit: 1 second
Measuring capacity: 59' 59"
Measuring modes: Elapsed time, split time, two finishes
■ The current time setting is off by one hour.
You may need to change your Home City’s standard time/daylight saving time
(DST) setting. Use the procedure under “Adjusting the Digital Time and Date
Settings” (page E-17) to change the standard time/daylight saving time (DST)
setting.
World Time Mode
■ The time for my World Time City is off in the World Time Mode.
This could be due to incorrect switching between standard time and daylight saving
time. See “To specify standard time or daylight saving time (DST) for a city” (page
E-22) for more information.
E-40
E-41
Countdown Timer:
Measuring unit: 1 second
Countdown range: 60 minutes
Countdown start time setting range: 1 to 60 minutes (1-minute increments)
Alarms: 5 daily alarms (with 1 snooze alarm); Hourly time signal
Illumination: Ultraviolet LED (light-emitting diode); selectable illumination duration
(approximately 1.5 seconds or 3 seconds)
Power Supply: Two silver oxide batteries (Type: SR726W)
Approximately 2 years on type SR726W (assuming alarm operation 20 seconds
per day and one illumination operation 1.5 seconds per day)
City Code Table
Frequent use of illumination runs down the battery.
E-42
L-1
City Code Table
City
Code
–––
HNL
ANC
LAX
DEN
CHI
NYC
CCS*
RIO
–––
–––
GMT
LON
PAR
CAI
JRS
L-2
UTC Offset/
GMT Differential
–11
Honolulu
–10
Anchorage
–9
Los Angeles
–8
Denver
–7
Chicago
–6
New York
–5
Caracas
–4
Rio De Janeiro
–3
–2
–1
City
London
Paris
Cairo
Jerusalem
0
+1
+2
City
Code
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
HKG
TYO
ADL
SYD
NOU
WLG
City
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
Hong Kong
Tokyo
Adelaide
Sydney
Noumea
Wellington
UTC Offset/
GMT Differential
+3
+3.5
+4
+4.5
+5
+5.5
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
xBased
on data as of December 2010.
xThe
rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
* In December 2007, the UTC offset for Caracas, Venezuela (CCS) was changed
from –4 to –4.5. However, this watch still uses the old UTC offset of –4 when the
Caracas (CCS) city code is selected.
L-3