Casio EX-ZR400 Camcorder User Manual

SG2, SG3 Spray Guns
English
Models: 243011, 243012, 246506, 243238, 243382, 289843, 257359
312830C
IMPORTANT SAFETY INSTRUCTIONS. Refer to your
sprayer instruction manual for Pressure Relief, priming and
spray instructions. Keep these instructions.
ti11562a
Maximum Working Pressure: 3600 psi (248 bar, 24.8 MPa)
-
For the application of architectural paints and coatings -
The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point
symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings.
Additional, product-specific warnings may be found throughout the body of this manual where applicable.
EQUIPMENT MISUSE HAZARD
WARNINGS
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured
components will pierce skin. This may look like just a
cut, but it is a serious injury that can result in amputation. Get
immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove,
or rag.
• Do not spray without tip guard and trigger guard
installed.
• Engage trigger lock when not spraying.
• Follow Pressure Relief Procedure in this manual, when
you stop spraying and before cleaning, checking, or servicing equipment.
Instructions/Parts
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes,
in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths
(potential static arc).
• Keep work area free of debris, including solvent, rags
and gasoline.
• Do not plug or unplug power cords, or turn power or light
switches on or off when flammable fumes are present.
• Ground all equipment in the work area. See Grounding
instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering
into pail.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2008, Graco Inc. is registered to I.S. EN ISO 9001
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component.
See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment
manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material,
request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s
replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your
distributor for information.
• Route hoses and cables away from traffic areas, sharp
edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull
equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum
equipment. Such use can cause serious chemical reaction
and equipment rupture, and result in death, serious injury,
and property damage.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment
when operating, servicing, or in the operating area of
the equipment to help protect you from serious
injury. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and
solvent manufacturer
• Gloves
• Hearing protection
Pressure Relief Procedure
Installing Tip (26) and Guard (25) on Gun
WARNING
WARNING
Follow this Pressure Relief Procedure
whenever instructed to relieve pressure,
stop spraying, check or service equipment,
or install or clean spray tip.
1.
2.
Turn OFF power and turn sprayer pressure control to lowest pressure setting.
Hold gun against side of flushing pail. Trigger gun into pail
to relieve pressure.
If you suspect spray tip or hose is clogged or that pressure has
not been fully relieved after following the steps above, VERY
SLOWLY loosen tip guard retaining nut or hose end coupling
to relieve pressure gradually, then loosen completely. Clear
hose or tip obstruction.
Gun Trigger Lock
3.
4.
Operation
Spraying
1.
2.
3.
4.
WARNING
To prevent injury when the gun is not in use, always
set the gun’s trigger lock if unit is being shut down
or left unattended.
Trigger Locked
Trigger Unlocked
(no spray)
(spray)
WARNING
1.Relieve pressure. Set trigger lock.
3.
ti11308a
Setup
4.
1.
2.
Connect Gun to Sprayer
3.
3.
2
(4) Vertical
ti11563a
WARNING
Make sure sprayer is turned off and unplugged from power
source. Refer to your sprayer instruction manual for priming
and spray instructions.
Attach supply hose to sprayer fluid outlet.
Attach other end of supply hose to gun swivel (5). Use two
wrenches (one on the swivel (5) and one on the hose), to
tighten all connections securely.
Refer to sprayer instruction manual for priming
instructions.
Loosen guard
(3) Horizontal
retaining nut.
Align guard (25)
horizontally to
spray a horizontal
pattern.
Align guard (25)
vertically to spray ti11564a
a vertical pattern.
Clearing Clogs
WARNING
1.
2.
Unlock trigger lock.
Be sure the arrow shaped tip (26) faces forward (spray).
Hold gun perpendicular and approximately 12-inches
(30 cm) from surface. Move gun first, then pull gun trigger
(3) to spray a test pattern.
Slowly increase pump pressure until coverage is uniform
and even (see sprayer instruction manual for additional
information).
Aligning Spray
2.
ti11309a
1.If equipment has recently been operated,
relieve pressure. Set trigger lock.
2.Using a pencil or similar object, insert seal
(24) into back of guard (25).
Install guard (25) over end of gun (1).
Insert tip (26) in guard (25). Tighten retaining nut.
Relieve pressure. Set trigger lock.
Rotate tip (26) 180°. Unlock trigger lock. Trigger gun into
pail or onto ground to remove clog.
Set trigger lock. Rotate tip (26) 180° back to spray
position.
Cleanup
Flush gun after each work shift and store in a dry location. Do
not leave the gun or any parts in water or cleaning solvents.
312830C
Parts
33
*Kit 288817 repairs both
series A and B guns.
1c
1a
26
8
1a replaces these three
components of series A.
10
32
Series A
7
6
1b
1a
Series B
4
3
23
22
24
5
Ref.
1
1a
1b
1c
3
Part
288817
115483
243639
4
5
195495
238817
195384
243084
218131
179733
195395
115484
6✓
7✓
8
10
Description
KIT, repair, gun (includes 1a, 1b, 1c)
SEAT, valve
NEEDLE, gun
NUT, lock
TRIGGER, repair kit
includes 32, 33
GUARD, trigger
KIT, swivel
ADAPTER, gun inlet (SG2)
FILTER, gun, SG2/SG3
FILTER, gun, SG3-E/SG3-A
SEAL, sleeve
CAP, end
PIN, actuator
Qty.
1
1
1
1
1
1
1
1
1
1
1
2
Ref.
22
23
Part
113409
195393
195788
195920
115485
195389
195390
177538
105334
24
26
32
33
Description
RETAINER, guard
HANDLE, gun (SG2)
HANDLE, gun (SG3, SG3-E)
HANDLE, gun (SG3-A)
O-RING
HOUSING, fluid (SG2)
HOUSING, fluid, (SG3 ALL)
STUD, trigger
NUT, lock, hex
▲ Replacement Warning labels, tags and cards are available
at no cost.
✓ Keep these spare parts on hand to reduce down time
Ref Part
24
26
24
25
RAC X
26
ti11561a
ti11739a
24
25
312830C
Qty.
1
1
1
1
1
1
1
1
1
RAC 5
RAC IV
25
ti15355a
26
Description
24 243004 OneSeal™, RAC IV (2-pack)
243281 OneSeal™, RAC 5 (5-pack)
246453 OneSeal™, RAC X (5-pack)
25 237859 GUARD, RAC IV
243161 GUARD, RAC 5
246215 GUARD, RAC X
26 221515 TIP, spray 515, RAC IV
286515 TIP, spray 515, RAC 5
LTX515 TIP, spray 515, RAC X
Qty
1
1
1
1
1
1
1
1
1
ti8505b
3
Maintenance
WARNING
WARNING
Before performing any maintenance on gun, read all warnings
on front cover of this manual and relieve pressure.
Cleaning/Replacing Filter (6)
1.Relieve pressure. Set trigger lock
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect fluid hose from gun at swivel (5).
Disconnect trigger guard (4) from guard retainer (22).
Unscrew handle (23) from gun (1).
Remove filter (6) through top of handle (23).
Clean filter (6). Use a soft brush to loosen and remove
excess debris.
Insert clean filter (6) into handle (23).
Reattach handle (23) to gun (1). Tighten securely.
Reconnect trigger guard (4) to guard retainer (22).
Repair
Replacing Needle
1
a
15b
17
15a
16
ti11311b
Technical Data
1.Relieve pressure. Set trigger lock.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Remove tip (26) and guard (25) from gun (1).
Disconnect fluid hose from gun at swivel (5).
Squeeze trigger while unscrewing diffuser.
Remove locknut and end cap.
Tap out needle.
Use a soft brush to clean out internal passages of gun.
Grease o-rings of new needle using a non-silicon grease.
Guide new needle (15b) through front of gun .
Install end cap and locknut, loosely.
For needle housing (15a), apply medium strength (blue)
thread sealant to threads. Place gasket on diffuser/seat.
12. Squeeze trigger while installing needle housing. Torque
to 26-32 ft-lb (35-43 N•m).
Translated Manuals
French - 312831
Estonian - 312845
Spanish - 312832
Latvian - 312846
Dutch - 312833
Lithuanian - 312847
German - 312834
Polish - 312848
Italian - 312835
Hungarian - 312849
Turkish - 312836
Czech - 312850
Greek - 312837
Slovakian - 312851
Croatian - 312838
Slovenian - 312852
Portuguese - 312839
Romanian - 312853
Danish - 312840
Bulgarian - 312854
Finnish - 312841
Chinese - 312855
Swedish - 312842
Japanese - 312856
Norwegian - 312843
Korean - 312857
Russian - 312844
Translated manuals can be requested through a
distributor or at www.graco.com.
Maximum working pressure
3600 psi (248 bar, 24.8 MPa)
Fluid orifice size
0.125 in. (3.18 mm)
Weight (with tip and guard)
22 oz. (630 g)
Inlet
1/4 npsm swivel
Maximum material temperature
120°F (49°C)
Wetted parts
Stainless steel, polyurethane, nylon, aluminum, tungsten carbide, brass
Noise Level*
Sound power
87 dBa
Sound pressure
78 dBa
*Measured at 3.1 feet (1m) while spraying water-based paint, specific gravity 1.36, through a 517 tip at 3000 psi (207 bar, 20.7 MPa) per ISO 3744
For complete warranty information contact your local Graco distributor, call Graco customer service:
1-800-690-2894 or visit our website: www.graco.com.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 312830
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Revised 02/2010