Cateye CC-RD200 Microphone User Manual

START
CATEYE STRADA CADENCE
CC-RD200
Quick Start
Click the button and follow the instructions.
Thank you for purchasing our cyclocomputer CATEYE STRADA.
This Quick Start Manual explains how to set up the computer and how to install the unit on
your bicycle.
Please set up the unit according to the specified procedure, then it will be ready for use as a
cyclocomputer.
Before use, read the instruction manual that comes with the product thoroughly
to the end to understand the functions of this unit, and to use it safely in a
correct manner.
Next
This PDF contains a movie file.
When you click on the movie screen, a message regarding security appears. Click the
“Trust in the text” or “Play” button to close the message.
Click the screen again to play the movie.
Next
CATEYE STRADA CADENCE
Quick Start Manual
Click the item you wish to view.
Setting up the computer
How to install the sensor
How to install the bracket (movie)
Return to Cover
Contents
Operation of buttons
Set up the computer by operating the buttons as follows.
Check the button position before you start setting up.
Back
MENU
MODE
Press the MENU button and the MODE
button on the back of the computer.
Next
CATEYE STRADA CADENCE
Quick Start Manual
Setting up the computer
Clear all data (initialization)
Clear all data (initialization)
Press the AC button on the back of the computer.
After full lighting of the screen, the computer switches to the speed unit setting screen to start setup.
Setting the speed unit
Entering the tire
circumference
Return to Contents
AC
Setting the clock display
Setting the hour
Setting the minute
Full lighting
Measuring screen
(Setup completed)
Return
Setting the speed unit
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
Setting up the computer
Setting the speed unit
Clear all data (initialization)
When the MODE button is pressed, either “km/h” or “mph”
is selected for the speed unit display. Select the display of
your choice.
After selecting, press the MENU button to proceed to the
next step “Entering the tire circumference”.
Setting the speed unit
Entering the tire
circumference
Setting the clock display
Setting the speed unit
km/h ↔ mph
Setting the hour
To the next step
MENU
Setting the minute
MODE
Measuring screen
(Setup completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
Setting up the computer
Entering the tire circumference
Clear all data (initialization)
Enter the tire circumference (mm) of your bicycle with 4
digits using the tire circumference reference table.
Pressing the MODE button increases the value flashing,
and pressing and holding the MODE button moves to the
next digit.
After entering, press the MENU button to proceed to the
next step “Setting the clock display”.
Setting the speed unit
Entering the tire
circumference
Setting the clock display
Entering the tire
circumference
To the next step
Move digit
To the next step
Setting the hour
Setting the minute
Tire circumference reference table
Measuring screen
(Setup completed)
Return
MENU
MODE
MODE
(Press and hold)
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
Setting up the computer
Setting the clock display
Clear all data (initialization)
When you press and hold the MODE button, “24h” flashes.
When the MODE button is pressed, either “12h” or “24h”
is selected for the clock display. Select the display of
your choice.
After selecting, press and hold the MODE button to proceed to the next step “Setting the hour”.
Setting the speed unit
Entering the tire
circumference
Setting the clock display
Clock display
24h ↔ 12h
To the next step
MODE
MODE
Setting the hour
Setting the minute
Measuring screen
(Setup completed)
Return
(Press and hold)
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
Setting up the computer
Setting the hour
Clear all data (initialization)
Pressing the MODE button increases the value flashing
(“Hour” of the clock). Enter any value.
After entering, press and hold the MODE button to proceed to the next step “Setting the minute”.
Setting the speed unit
Entering the tire
circumference
Setting the clock display
Hour
To the next step
To the next step
MODE
MODE
Setting the hour
Setting the minute
Measuring screen
(Setup completed)
Return
(Press and hold)
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
Setting up the computer
Setting the minute
Clear all data (initialization)
Pressing the MODE button increases the value flashing
(“Minute” of the clock). Enter any value (Pressing and
holding MODE rapidly increases the value).
After entering, press the MENU button to switch to the
measuring screen.
Setting the speed unit
Entering the tire
circumference
Setting the clock display
Minute
To the next step
Setting the hour
Setup is completed
To the measuring screen
MENU
Setting the minute
MODE
Measuring screen
(Setup completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
Setting up the computer
Now, setup of the computer is completed.
Clear all data (initialization)
If the bracket and sensor are not installed on your bicycle,
return to Contents, click “How to install the bracket” and
How to install the sensor”, and then install them according to the instructions.
Setting the speed unit
Entering the tire
circumference
Setting the clock display
Measuring screen
Setting the hour
Setting the minute
Measuring screen
(Setup completed)
Return
Return Next
to Contents
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the bracket
• The Bracket being used in this movie is for wireless products and there is no wire attached.
• When you install the bracket band to your bicycle, tighten it so the wire will not be pinched by the stem
or handlebar.
Prepare the following parts from the packaged items.
Wheel magnet
Cadence magnet
Cadence sensor
Speed sensor
Nylon ties (x10)
Sensor rubber pad
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the sensor
Install the speed sensor
Install the speed sensor
Temporarily secure the speed sensor to the inside
of the left chain stay of your bicycle with two nylon
ties.
Tighten the speed sensor to such an extent that it
can be moved.
Install the wheel magnet
Install the cadence sensor
Install the cadence magnet
Speed sensor
Adjust the positions of the
sensor and magnet
Adjust the clearance between
the sensor and magnet
Nylon ties
Front
Route the cable
Left Chain Stay
Fixing the sensor and magnet
(Installation is completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the sensor
Install the wheel magnet
Install the speed sensor
Temporarily secure the wheel magnet to the left
spoke of the rear wheel.
Tighten the wheel magnet to such an extent that it
can be moved.
Install the wheel magnet
Install the cadence sensor
Install the cadence magnet
Rear wheel spoke
Adjust the positions of the
sensor and magnet
Wheel magnet
Adjust the clearance between
the sensor and magnet
Speed sensor
To the SENSOR LINE
Route the cable
Fixing the sensor and magnet
(Installation is completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the sensor
Install the cadence sensor
Install the speed sensor
Temporarily secure the cadence sensor to the outside of the left chain stay of your bicycle with two
nylon ties.
*When the clearance with the cadence magnet is
more than 3 mm, install the cadence sensor with
sensor rubber pads in layers. When temporarily
securing, keep allowance for sensor rubber pads.
Install the wheel magnet
Install the cadence sensor
Install the cadence magnet
Adjust the positions of the
sensor and magnet
Left Chain Stay
Nylon ties
Adjust the clearance between
the sensor and magnet
Front
Route the cable
Cadence sensor
Fixing the sensor and magnet
(Installation is completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the sensor
Install the cadence magnet
Install the speed sensor
Temporarily secure the cadence magnet to the inside of the left crank with nylon ties.
Tighten the cadence magnet to such an extent that
it can be moved.
Install the wheel magnet
Install the cadence sensor
Left crank (Inside)
Install the cadence magnet
Nylon ties
Adjust the positions of the
sensor and magnet
Cadence magnet
Adjust the clearance between
the sensor and magnet
Cadence sensor
To the SENSOR LINE
Route the cable
Fixing the sensor and magnet
(Installation is completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the sensor
Adjust the positions of the sensor and magnet
Install the speed sensor
Adjust the positions so that the wheel magnet passes through the SENSOR LINE of the speed sensor, and the cadence magnet passes through the
SENSOR LINE of the cadence sensor.
Install the wheel magnet
Install the cadence sensor
SENSOR LINE
(Cadence sensor)
Install the cadence magnet
Wheel magnet
Adjust the positions of the
sensor and magnet
Adjust the clearance between
the sensor and magnet
SENSOR LINE
(Speed sensor)
Route the cable
Cadence
magnet
Fixing the sensor and magnet
(Installation is completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Adjust the clearances between the speed sensor and
wheel magnet and the cadence sensor and cadence
magnet, so that both of them are within 3 mm.
*When the clearance between the cadence sensor
and cadence magnet is more than 3 mm, install the
cadence sensor with sensor rubber pads in layers.
Install the wheel magnet
Install the cadence sensor
Install the cadence magnet
Left Chain Stay (Outside)
Left Chain Stay (Inside)
3 mm
Adjust the clearance between
the sensor and magnet
Route the cable
How to install the sensor
Adjust the clearance between the sensor and magnet
Install the speed sensor
Adjust the positions of the
sensor and magnet
Return to Contents
3 mm
Speed sensor
Wheel magnet
Cadence sensor
Fixing the sensor and magnet
(Installation is completed)
Cadence magnet
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the sensor
Route the cable
Install the speed sensor
Fix the wire to the frame with nylon ties where applicable, and route it to the handle while winding
around the brake cable. Cut off any excess nylon tie
using a nipper.
section so that the wire is
Caution:Adjust this
not stretched when you turn the handle.
Install the wheel magnet
Install the cadence sensor
Install the cadence magnet
Nylon ties
Adjust the positions of the
sensor and magnet
Adjust the clearance between
the sensor and magnet
Route the cable
Fixing the sensor and magnet
(Installation is completed)
Return
Next
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
How to install the sensor
Fixing the sensor and magnet
Install the speed sensor
Firmly tighten each sensor and magnet, and cut off
any excess nylon tie using a nipper.
Install the wheel magnet
Now, sensor installation is completed. See how to install the bracket, and then complete the installation.
When the computer is not set up, return to Contents, click “Setting up the computer”, and follow
the instructions.
Install the cadence sensor
Install the cadence magnet
Adjust the positions of the
sensor and magnet
Adjust the clearance between
the sensor and magnet
Route the cable
Fixing the sensor and magnet
(Installation is completed)
Return
Return Next
to Contents
CATEYE STRADA CADENCE
Quick Start Manual
Return to Contents
Setting up the computer
Tire circumference reference table
ETRTO
47-203
54-203
40-254
47-254
40-305
47-305
54-305
28-349
37-349
32-369
40-355
47-355
32-406
35-406
Tire size
12x1.75
12x1.95
14x1.50
14x1.75
16x1.50
16x1.75
16x2.00
16x1-1/8
16x1-3/8
17x1-1/4 (369)
18x1.50
18x1.75
20x1.25
20x1.35
L (mm)
935
940
1020
1055
1185
1195
1245
1290
1300
1340
1340
1350
1450
1460
ETRTO
40-406
47-406
50-406
28-451
37-451
37-501
40-501
47-507
50-507
54-507
25-520
Tire size
20x1.50
20X1.75
20x1.95
20x1-1/8
20x1-3/8
22x1-3/8
22x1-1/2
24x1.75
24x2.00
24x2.125
24x1 (520)
24x3/4 Tubular
28-540 24x1-1/8
32-540 24x1-1/4
L (mm)
1490
1515
1565
1545
1615
1770
1785
1890
1925
1965
1753
1785
1795
1905
ETRTO
25-559
32-559
37-559
40-559
47-559
50-559
54-559
57-559
58-559
75-559
28-590
37-590
37-584
Tire size
L (mm)
26x1 (559)
1913
26x1.25
1950
26x1.40
2005
26x1.50
2010
26x1.75
2023
26x1.95
2050
26x2.10
2068
26x2.125
2070
26x2.35
2083
26x3.00
2170
26x1-1/8
1970
26x1-3/8
2068
26x1-1/2
2100
650C Tubular 26x7/8
1920
ETRTO
20-571
23-571
25-571
40-590
40-584
25-630
28-630
32-630
37-630
18-622
19-622
20-622
23-622
25-622
Tire size
650x20C
650x23C
650x25C 26x1 (571)
650x38A
650x38B
27x1 (630)
27x1-1/8
27x1-1/4
27x1-3/8
700x18C
700x19C
700x20C
700x23C
700x25C
L (mm)
1938
1944
1952
2125
2105
2145
2155
2161
2169
2070
2080
2086
2096
2105
ETRTO
28-622
30-622
32-622
35-622
38-622
40-622
42-622
44-622
45-622
47-622
54-622
60-622
Tire size
700x28C
700x30C
700x32C
700C Tubular
700x35C
700x38C
700x40C
700x42C
700x44C
700x45C
700x47C
29x2.1
29x2.3
L (mm)
2136
2146
2155
2130
2168
2180
2200
2224
2235
2242
2268
2288
2326
Measure the tire circumference (L) of your bicycle
Adjust the tire pressure properly. With the rider’s weight applied on the bicycle,
roll the wheel one tire revolution with reference to a marker such as the valve, and
measure the travel distance on the ground.
Return
L mm
Download PDF

advertising