Celestron 21066-DX-AL Telescope User Manual

Instructions for use
WASHING MACHINE
Contents
GB
English, 1
GB
Installation, 2-3-4-5
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 4
Technical details, 5
Washing machine description, 6-7
Control panel, 6
Display, 7
“MEMO” Programme, 7
Starting and Programmes, 8
Briefly: how to start a programme, 8
Programme table, 8
Personalisations, 9
WIXE 127
Setting the spin cycle, 9
Setting the Delay Timer, 9
Setting the temperature, 9
Functions, 9
Detergents and laundry, 10
Detergent dispenser, 10
Bleach cycle, 10
Preparing your laundry, 10
Special items, 10
Woolmark, 10
Precautions and advice, 11
General safety, 11
Disposal, 11
Saving energy and respecting the environment, 11
Care and maintenance, 12
Cutting off the water or electricity supply, 12
Cleaning your appliance, 12
Cleaning the detergent dispenser, 12
Caring for your appliance door and drum, 12
Cleaning the pump, 12
Checking the water inlet hose, 12
Troubleshooting, 13
Service and Guarantee, 14-15-16
Before calling for Assistance, 14
Guarantee, 15-16
1
Installation
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
GB
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the 3
protective screws and
the rubber bush with the
respective spacer,
situated on the rear of
the appliance (see also
the installation leaflet).
NB:The plastic spacers
may fall down inside the
machine once the bolt
has been removed, and will not interfere with the
operation of the machine.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
3. Make sure there are no kinks or bends in the hose.
Packaging materials are not children's toys.
The water pressure at the tap must be within the
Levelling
Your machine may make a considerable amount of noise
if the two front feet have not been adjusted correctly.
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compensate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure);
the angle of inclination,
measured according to
the worktop, must not
exceed 2°.
2
A
1. Insert seal A into the
end of the inlet hose
and screw the latter
onto a cold water tap
with a 3/4 gas threaded
mouth (see figure).
Before making the
connection, allow the
water to run freely until
it is perfectly clear.
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Ensure that the supply taps are allowing water
through. Old taps may seize in the closed position
and thus prevent water reaching the machine.
Connecting the drain hose
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Before plugging the appliance into the mains
socket, make sure that:
• the socket is earthed and in compliance with the
applicable law;
Service
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow Earth
Blue
Neutral
Brown
Live
Troubleshooting
Electric connection
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Care
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self -syphon
ie. continuously empty as it is filling.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
the plug is replaced by a fused 13 ampere rewearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the
appliance.
Precautions
We advise against the use of hose extensions; in
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking
or the colour that is embossed in words on the base
of the plug. Replacements can be obtained directly
from your nearest Service Depot.
Detergents
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Programmes
Where it connects
to the waste water
pipe cut end off
spigot or remove the
blanking cap
The drain hose may be
connected to an
under-sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
Description
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
GB
Installation
65 - 100 cm
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
• the supply voltage is included within the values i
ndicated on the Technical details table
(see page 5);
3
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or coloured Green or Green & Yellow.
or
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
NEUTRAL (N)
BROWN
LIVE (L)
GREEN & YELLOW
EARTH (E)
GB
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
When the washing machine is installed, the mains
socket must be within easy reach.
Do not use extensions or multiple sockets.
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
4
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
GB
Technical details
59.5 cm wide
85 cm high
52.5 cm deep
Capacity
from 1 to 6 kg
Electric
connections
please refer to the technical data plate
fixed to the machine
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Spin speed
up to 1200 rpm
Control
programmes
according to
EN 60456
directive
programme 2; temperature 60°C;
run with a load of 6 kg.
Programmes
Dimensions
Description
WIXE 127
Installation
Model
Detergents
This appliance is compliant with the
following European Community
Directives:
- 73/23/CEE of 19/02/73 (Low
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
Precautions
Care
Troubleshooting
Service
5
Washing machine description
Control panel
FUNCTION
GB
Buttons
START/RESET
button
START/STOP
button
Display
Detergent dispenser
Control knob
TEMPERATURE
button
SPIN
button
Detergent dispenser to add detergent and fabric
softener (see page 10).
SPIN button to adjust the spin speed or exclude it
altogether (see page 9).
DELAY TIMER button to delay the start of the set
programme for a maximum period of 24 hours
(see page 9).
TEMPERATURE button to adjust the wash temperature (see page 9).
Display to programme the washing machine and
follow the wash cycle progress (see opposite page).
6
DELAY TIMER
button
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
START/RESET button to start the programmes or
cancel any incorrect settings.
START/STOP button to turn the washing machine
on and off.
Control knob to select the wash programmes.
The knob stays still during the cycle.
Display
GB
Description
Once you have pressed the START/RESET button to
start the programme, the display will indicate the
amount of time left until the end of the wash cycle. If
a delayed start has been set (using the Delay Timer,
see page 9), the delay time will be indicated on the
display.
Installation
In addition to being a practical tool to programme your appliance (see page 9), the display provides useful
information concerning the wash cycle.
Programmes
At the end of the programme, the word END is displayed.
Detergents
Door lock:
If the symbol is on, the washing machine door is locked to prevent it from being opened accidentally. To avoid
any damages, wait for the symbol to switch itself off before you open the appliance door.
In the event of an anomaly, an error code will appear, such as: F-01, (see page 13).
Precautions
Care
Service
This programme allows you to store your favourite or most-used wash cycle.
; the
All you have to do is set the desired programme and, once it has started, turn the KNOB to position
wash cycle will be stored automatically and the word MEMO appears on the display, flashing for a few seconds.
; you will be able to
Subsequently, you can start the "MEMO" cycle by simply turning the KNOB to position
see the temperature/spin cycle/delay timer values by pressing the corresponding buttons; you will also be able to
modify them but this variation will only be valid for the programme in progress and it will not be stored in the
"MEMO" cycle.
If you want to store a new wash cycle, repeat the above-mentioned operations.
Troubleshooting
"MEMO" Programme
7
Starting and Programmes
Briefly: starting a programme
GB
5. Add the detergent and any fabric softener
(see page 10).
6. Start the programme by pressing the START/RESET
button for one second.
To cancel it, keep the START/RESET button
pressed for at least 2 seconds.
7. When the programme has ended, the word END is
displayed. Take out your laundry and leave the
appliance door ajar to allow the drum to dry
thoroughly.
.
8. Turn the washing machine off by pressing button
1. Turn the washing machine on by pressing button
.
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the knob to the desired programme. The
estimated duration of the selected programme is
displayed. The temperature and spin speed are
automatically set according to the programme
(to change them, see page 9).
4. Select any functions (see page 9).
Programme table
Typ e of fab ric and
d e gre e of soil
P rogr.
Te m p era ture
D e tergent
Fabric
softener
p rew as h
w as h
•
•
•
M ax.
C ycle
Sp in
Stain rem ova l
length
D e scrip tion of wash c ycle
Sp eed s
op tion/b le ach
(m inutes)
(r.p .m .)
S tan d ard
Cotton: Extremely soiled whites
1
9 0 °C
2
9 0 °C
•
•
2
6 0 °C
•
•
2
4 0 °C
•
•
3
4 0 °C
•
•
4
5 0 °C
•
4
4 0 °C
W ool
5
Very delicate fabrics
(cu rtain s , silk, visco se, etc.)
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
18 0
Max.
16 5
Max.
15 0
Max.
105
Max.
D elicate/
Traditio n al
70
Max.
•
D elicate
72
800
•
•
D elicate
60
800
4 0 °C
•
•
D elicate
50
600
6
3 0 °C
•
•
45
no
7
6 0 °C
•
•
60
Max.
Wash cycle, rinse cycles,
intermediate and final spin cycles
8
4 0 °C
•
•
50
Max.
Wash cycle, rinse cycles,
intermediate and final spin cycles
9
40 °C
•
•
40
800
10
3 0 °C
•
•
30
800
Sports shoes (MAX. 2 pairs)
11
30 °C
•
•
50
800
Cold w ash (w ithout detergents),
w ash cycle, rinse cycles, and
delicate spin cycle
Fabrics for sportswear
(Tracksuits, shorts, etc.)
12
3 0 °C
•
•
60
600
Wash cycle, rinse cycles,
intermediate and final spin cycles
800
R in se cycles an d s pin cycle
Spin
800
Draining and spin cycle
D rain
no
(sheets, tablecloths, etc.)
Cotton: Extremely soiled whites
(sheets, tablecloths, etc.)
Cotton: Heavily soiled w hites
and fast colours
Cotton: Heavily soiled w hites
and delicate colours
C otton: Sligh tly so iled w h ites
an d delicate colo u rs (s h irts ,
ju mpers, etc.)
Synthetic s: Heavily so iled
fas t co lo u rs (baby lin en , etc.)
Synthetic s: Heavily so iled
fas t co lo u rs (baby lin en , etc.)
D elicate/
Traditio n al
D elicate/
Traditio n al
D elicate/
Traditio n al
Wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rin se cycles, an ticrease or delicate spin cycle
Wash cycle, rin se cycles, an ticrease or delicate spin cycle
W as h cycle, rin se cycles an d
delicate spin cycle
W as h cycle, rin se cycles, an ticreas e or drain in g cycle
Tim e 4 y o u
C otton: Heavily so iled w h ites
an d fas t co lo u rs
C otton: Sligh tly so iled w h ites
an d delicate colo u rs (s h irts ,
ju mpers, etc.)
Synthetics: Delicate colours (all
types of slightly soiled garments)
Synthetics: Delicate colours (all
types of slightly soiled garments)
Wash cycle, rin se cycles,
delicate spin cycle
W as h cycle, rin se cycles an d
delicate spin cycle
S p o rt
M EM O
A llow s fo r an y w ash cycle to be sto red (s ee pag . 7)
PAR TIAL P R O G R AM M E S
R in se
•
D elicate/
Traditio n al
D rain in g
Notes
-For programmes 7 and 8, we advise against exceeding a wash load of 3.5 kg.
-For programme 12 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily (programme 10 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (10 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
8
Personalisations
FUNCTION buttons
Setting the spin cycle
Programmes
Press the button
and you will see the word OFF on the
display, while the relative symbol flashes.
Press the button again and "1h" appears, that is, a delay of one
hour (this can reach up to 24h); stop on the "desired" delay; after
approximately 2 seconds the setting is accepted, following which,
the time for the set programme appears on the display and the
remains on.
symbol
If you now press the START/RESET button, the set "delay"
appears; this decreases every hour until the start of the cycle. In this phase, the "delay" can only be modified by
decreasing it. The Delay Timer regulation is enabled with all programmes.
Description
Setting the Delay Timer
GB
Installation
If, when the appliance is switched on, the KNOB is positioned on
appears. Press button
a programme with a spin cycle, a fixed
and the maximum spin speed allowed for the programme set
will be displayed, and the
icon flashes. Press it again and the
values lower until they reach OFF, which indicates that the spin
cycle has been excluded (press it again to go back to the
maximum value); stop on the desired speed, after approximately
remains fixed.
2 seconds the setting is accepted: the symbol
The spin cycle setting is enabled with all the programmes except
for 6 and the Draining cycle.
Setting the temperature
Detergents
If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs
to be regulated, a fixed appears. Press button and the maximum temperature allowed for the programme set
will be displayed and the icon flashes. Press it again and the temperature lowers until it reaches OFF, which
indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value, after
approximately 2 seconds the setting is accepted: the symbol remains fixed.
The temperature adjustment is enabled with all wash programmes.
Functions
Enabled with
programmes:
Stain
removal
Bleaching cycle
designed to
remove the
toughest stains.
Please remember to pour the bleach into extra compartment 4
(see page 10).
This function is incompatible with the EASY IRON function.
2, 3, 4, 5,
Rinse cycle.
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, 3, 4, 7,
8, 9, 11, 12,
Rinse cycle.
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 4 and 6 will end, with the
laundry left to soak (Anti-crease), and the relative button flashes:
- to conclude the cycle, press the START/RESET button or the
EASY IRON button;
- to run the draining cycle alone, set the knob to the relative
symbol
and press the START/RESET button.
This function is incompatible with the STAIN REMOVAL function.
3, 4, 6, 7, 8, 9,
Rinse cycle.
Extra Rinse
Easy iron
The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the
final spin speed if an unbalanced load is detected.
Service
Comments
Troubleshooting
Effect
Care
Function
Precautions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set. If you set a function that is incompatible with another function you selected previously, only the
last one selected will be enabled.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.
9
Detergents and laundry
GB
Detergent dispenser
Preparing your laundry
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
• Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
• Empty all pockets and check for loose buttons.
• Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 6 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1,5 kg
4
1
2
3
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
How much does your laundry weigh?
compartment 1: Detergent for pre-wash
(powder)
Before pouring in the detergent, make sure that
extra compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
extra compartment 4: Bleach
Do not use hand wash detergent because it may
form too much foam.
Bleach cycle
Traditional bleach should be used on sturdy
white fabrics, and delicate bleach for coloured
fabrics, synthetics and for wool.
Place extra
compartment 4,
provided, into
compartment 1.
When pouring in the
bleach, be careful not to
exceed the "max" level
indicated on the central
pivot (see figure).
To run the bleach cycle alone, pour the bleach into extra
and
compartment 4, set the Rinse programme
enable the Stain removal function (see page 9).
To bleach during a wash cycle, pour in the detergent
and fabric softener, set the desired programme and
enable the Stain removal function (see page 9).
The use of extra compartment 4 excludes the
possibility of using the pre-wash cycle.
10
1
1
1
1
1
sheet 400-500 g
pillow case 150-200 g
tablecloth 400-500 g
bathrobe 900-1,200 g
towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 6
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1,5 kg.
Woolmark
As gentle as a hand wash.
Indesit sets a new standard of superior
performance that has been endorsed by The
Woolmark Company with the prestigious Woolmark
brand. Look for the Woolmark logo on the washing
machine to ensure you can safely and effectively
wash wool garments labelled as "hand wash"
(M.0303):
Set programme 5 for all "Hand wash" garments
(max 1,5 kg), using the appropriate detergent.
Precautions and advice
General safety
• This appliance has been designed for nonprofessional, household use and its functions must
not be changed.
• Never touch the washing machine when barefoot
or with wet or damp hands or feet.
• Do not open the detergent dispenser while the
appliance is in operation.
• Do not touch the drain water as it could reach
very high temperatures.
• In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
• The appliance door tends to get quite hot during
the wash cycle.
• Before loading your laundry into the washing
machine, make sure the drum is empty.
• Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
• Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
• If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 9) helps to
organise your wash cycles accordingly.
• If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
Service
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal
waste stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the
• Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
Troubleshooting
Disposal
• The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Care
• Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
Saving on detergent, water, energy and time
• To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
Precautions
• Always keep children well away from the
appliance while in operation.
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Indesit
technology, your washing machine only needs less
than half the amount of water to get the best
results: an objective reached to respect the
environment.
Detergents
• Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
Saving energy and respecting the
environment
Programmes
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
GB
Description
• This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
environment. The crossed out "wheeled bin"
symbol on the product reminds you of your
obligation, that when you dispose of the appliance
it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Installation
The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
11
Care and maintenance
Cutting off the water or electricity
supply
GB
• Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
• Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
2. unscrew the lid
rotating it anticlockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
Caring for your appliance door and
drum
• Always leave the appliance door ajar to prevent
unpleasant odours from forming.
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
Never use hoses that have already been used.
12
Troubleshooting
Your washing machine could fail to work. Before calling for Assistance (see page 14), make sure the problem
can't easily be solved by consulting the following list.
GB
The washing machine does not
drain or spin.
• Some programs have a slower final spin to taked best care of the
fabrics. See page 8 for details of the final spin speed for each program.
• The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 8).
• The “Easy iron” function is enabled: to complete the programme,
press the START/RESET button (see page 9).
• The drain hose is bent (see page 3).
• Remove the drain hose from the standpipe or under-sink trap and check for
blockages, ensuring that the water can drain freely away from the machine.
The washing machine vibrates
too much during the spin cycle.
• When the machine is installed, the locking screws for the oscillating
assembly are still in place. Remove the screws (see page 2).
• The washing machine is not level (see page 2).
• The washing machine is closed in between furniture cabinets and
the wall (see page 2).
The machine is locked and the
display flashes, indicating an
error code (e.g. F-01, F-..).
• This means there is a problem with the machine. Before calling
Assistance, please follow the set of instructions below:
1. Switch off the machine;
2. Remove the plug connecting the appliance to the mains supply
and wait for at least 40 seconds;
3. Place the plug back into the socket;
4. Switch on the machine;
5. If the problem is still evident after this process has been carried out,
contact Assistance.
The washing machine leaks.
• The water inlet hose is not screwed on correctly (see page 2).
• The detergent dispenser is obstructed (to clean it, see page 12).
• The drain hose is not secured properly (see page 3).
There is too much foam.
• The detergent is not suitable for machine washing (it should bear the
definition "for washing machines" or "hand and machine wash", or the like).
• You used too much detergent.
Service
• The drain hose is too low or too far in to the stand pipe (see page 3) for
correct installation.
• The wall drainage system doesn't have a standard pipe (min. 38 mm).
Troubleshooting
The machine continuously fills
and empties with water.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
Care
•
•
•
•
•
•
Precautions
The washing machine does not
fill with water (The wording
H2O is displayed).
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly (the word DOOR is displayed).
button has not been pressed.
The
The START/RESET button has not been pressed.
NB: It should be held minimum one second.
• The water tap is not turned on.
• A delayed start has been set (using the Delay Timer, see page 9).
Detergents
•
•
•
•
•
Programmes
The washing machine won't
start.
Description
Possible causes/Solution:
Installation
Problem
13
Service
Before calling for Assistance:
• Check whether you can solve the problem on your own (see page 13);
• Restart the programme to check whether the problem has been solved;
• If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
GB
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout service.
Always request the assistance of authorised servicemen.
Notify the operator of:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
14
Guarantee
12 Months Parts and Labour Guarantee
GB
Installation
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
-
Description
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
Programmes
The guarantee does not cover:
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory . These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
Detergents
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
Extended Guarantees
Precautions
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on
08709 088 088 (ROI 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any
technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08709 066 066
(ROI 0818 313 413)for telephone assistance, or, where necessary, to arrange for an engineer to call.
Care
Troubleshooting
Service
15
195064819.00
05/2007 - Xerox Business Services
After Sales Service
GB
No one is better placed to care for your Indesit appliance during the course of its working life than us - the
manufacturer.
Essential Contact Information
Indesit Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified
engineers on call to ensure you receive fast, reliable, local service.
UK: 08709 066 066
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean
your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08709 077 077
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality,
recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door,
plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the
appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.
16