Operating instructions | Central Hydraulics 916315 Automobile Parts User Manual

SCISSOR LIFT
6,000 LBS. CAPACITY - 48” HEIGHT
Model 91315
Set up And Operating Instructions
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised 06k, 07j
SPECIFICATIONS
Electrical Requirements
220V / 50-60 Hz, 12 FLA / Duty Cycle: 5 min,
2 HP / Single Phase, Dedicated 20A circuit required
Requires a single phase, 3-prong 250V/20A (NEMA L6-20P) power plug (not
included).
Maximum Lifting
Capacity
6000 Pounds (48” Mid-Rise Scissor Lift)
Minimum Lift Height
7” At Pads
Maximum Lift Height
41/2’ At Pads
Overall Dimensions
993/4” L x 391/2” W x 7” H (Fully Lowered)
Piston Rod Travel
201/2”
Pump Type
Hydraulic/Electro w/Steel Dolly
Pump Hydraulic Oil
Capacity/Type
6.5 Quarts
ISO VG 32 Hydraulic Oil
(Extreme temperature conditions may require an oil with a different
viscosity – consult a qualified technician.)
Weight
849 Pounds
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists
on pages 17, 18, and 19 are included. If any parts are missing or broken, please
call Harbor Freight Tools at the number shown on the cover of this manual as soon as
possible.
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and assembly
diagram. Keep your invoice with this manual. Write the invoice number on the inside
of the front cover. Keep this manual and invoice in a safe and dry place for future
reference.
GENERAL SAFETY RULES
WARNING! Read all instructions
Failure to follow all instructions listed below may result in electric shock,
fire, and/or serious injury. The term “power tool” in all of the warnings listed
below refers to your line-operated (corded) power tool or battery-operated
(cordless) power tool.
SAVE THESE INSTRUCTIONS
REV 05l, 06k, 07j
SKU 91315
For technical questions, please call 1-800-444-3353.
Page WORK AREA
1.
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
2.
Do not operate power equipment in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power equipment can create
sparks which may ignite flammables.
3.
Keep bystanders, children, and visitors away while operating power
equipment. Distractions can cause you to lose control.
PERSONAL SAFETY
1.
Stay alert. Watch what you are doing, and use common sense when
operating power equipment. Do not use power equipment while tired or
under the influence of drugs, alcohol, or medication. A moment of inattention
while operating power equipment may result in serious personal injury.
2.
Risk of Entanglement! Dress properly. Do not wear loose
clothing or jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
3.
Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Plugging in power equipment with the Power Switch on invites accidents.
4.
Remove adjusting keys or wrenches before turning on power equipment.
A wrench or a key that is left attached to a moving part of power equipment may
result in personal injury.
5.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power equipment in unexpected
situations.
6.
Use safety equipment. Always wear ANSI approved safety impact eye
goggles underneath a full face shield.
TOOL USE AND CARE
1.
Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
2.
Do not force power equipment. Use the correct equipment for your
application. The correct equipment will do the job better and safer at the rate for
which it is designed.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 3.
Do not use power equipment if the Power Switch does not turn it on or off.
Any equipment that cannot be controlled with the Power Switch is dangerous and
must be repaired or replaced.
4.
Disconnect the Power Cord Plug from the power source before making
any adjustments, changing accessories, or storing the power equipment.
Such preventive safety measures reduce the risk of starting the equipment
accidentally.
5.
Store idle equipment out of reach of children and other untrained persons.
Power equipment is dangerous in the hands of untrained users.
6.
Maintain power equipment with care. Properly maintained equipment are less
likely to fail and are easier to control. Do not use damaged power equipment.
Tag damaged power equipment “Do not use” until repaired.
7.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the power equipment’s operation. If
damaged, have the equipment serviced before using. Many accidents are
caused by poorly maintained power equipment.
8.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one power equipment may become
hazardous when used on another power equipment.
SERVICE
1.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
2.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
ELECTRICAL SAFETY
1.
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
2.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation
eliminates the need for the
three wire grounded power cord and grounded power supply system.
3.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
4.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
5.
Do not abuse the Power Cord. Never use the Power Cord to carry the
tools or pull the Plug from an outlet. Keep the Power Cord away from
heat, oil, sharp edges, or moving parts. Replace damaged Power Cords
immediately. Damaged Power Cords increase the risk of electric shock.
6.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
WARNING!
IMPORTANT! A 220V / 50-60 Hz, 12 FLA / Duty Cycle: 5 min, 2 HP /
Single Phase, Dedicated 20A circuit is required. It also requires a
single phase, 3-prong 250V/20A (NEMA L6-20P) power plug (not
included).
THIS WIRING PROCEDURE MUST ONLY BE DONE BY A QUALIFIED,
CERTIFIED ELECTRICIAN!
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~
A
Volts Alternating Current
Amperes
No Load Revolutions per Minute
n0 xxxx/min. (RPM)
SPECIFIC SAFETY RULES
1.
DANGER! Make sure you know the weight of the vehicle you are
going to lift before using the Scissor Lift. Do not exceed the maximum lift
capacity (6,000 pounds at 48” elevation) for the Scissor Lift. Overloading the
Scissor Lift could cause personal injury and/or property damage. Be aware of
REV 07j
SKU 91315
For technical questions, please call 1-800-444-3353.
Page dynamic loading! If a weight suddenly falls onto the Scissor Lift, it may create for
a brief instant an excess load which may result in personal injury and/or damage
to the vehicle and Scissor Lift.
2.
Use the Scissor Lift only in well ventilated areas. Carbon monoxide
exhausted from running vehicle engines is a colorless, odorless fume that, if
inhaled, can cause serious personal injury or death.
3.
Maintain labels and nameplates on the Scissor Lift. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement. There is a WARNING label attached to the Scissor Lift. Read and
fully understand the contents of the WARNING label. Do not remove the warning
label from the Scissor Lift.
4.
Make sure to read and understand all instructions and safety precautions
as outlined in the manufacturer’s manual for the vehicle you are lifting. All
four Rubber Saddles (39B) of the Scissor Lift must be used when lifting a vehicle.
Always use the manufacturer’s recommended lifting points.
5.
Do not use the Scissor Lift on any asphalt surface. Make sure the Scissor
Lift is used on a dry, oil/grease free, flat, level, CONCRETE surface capable
of supporting the weight of the Scissor Lift, the vehicle being lifted, and any
additional tools and equipment. The concrete floor surface should have a
minimum thickness of 5”. The concrete must have a minimum strength of 4,000
PSI, and should be aged at least 30 days prior to use. Do not use the Scissor
Lift on concrete expansion seams or on cracked, defective concrete.
6.
Always examine the Scissor Lift for structural cracks, bends, damage to
the hydraulic hoses and electrical wiring, and any other condition that may
affect the safe operation of the Lift. Do not use the Scissor Lift even if minor
damage is detected.
7.
IMPORTANT! Operation (raising or lowering) of the Scissor Lift can be
immediately stopped at any time by releasing pressure on the Power
Switch located on the Motor (1A).
8.
Make sure the Oil Tank (13A) is completely filled (approx. 6.5 quarts) with a
premium quality hydraulic oil prior to operating the Scissor Lift.
9.
Always allow at least two seconds after the Motor (1A) starts to raise or
lower the Scissor Lift. Failure to do so may cause the Motor to burn out.
10.
Prior to beginning a job, make sure the Safety Lock Assembly (36B) and its
Safety Catches are in the proper position. NEVER work underneath a vehicle
without using additional safety support devices (i.e., jack stands) to support the
vehicle.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 11.
Always keep hands, fingers, and feet away from the moving parts of the
Scissor Lift when applying or releasing a load. Remain clear of the Scissor
Lift when raising or lowering a vehicle.
12.
Use extreme caution when applying or releasing a load. Never allow the load
to suddenly release. Slowly and carefully apply and release the load.
13.
Never leave the Scissor Lift unattended when the Lift is under a load.
Whenever the Scissor Lift is under a load there is a very large amount of force
that has been stored in the Outside/Inside Scissors (24B, 25B) which must be
controlled until the load is relaxed.
14.
Before driving a vehicle onto the Scissor Lift make sure the Lift is fully
lowered. Before driving a vehicle onto the Scissor Lift, position the Plates (42B)
and Rubber Saddles (39B) inward. Do not hit or run over the Plates and Rubber
Saddles, as this could damage the vehicle. Make sure the Scissor Lift is fully
lowered before driving the vehicle off.
15.
Should any weight component be removed from, or added to the vehicle,
use a jack stand (not included) to support the over balanced end during the
maintenance procedure. Do not operate the Scissor Lift if the vehicle load tilts
or binds during the up or down movement. Always position the vehicle with the
center of gravity midway between the Rubber Saddles (39B). Avoid excessive
rocking of the vehicle while it is in its raised position.
16.
Never lift a vehicle with anyone inside it. Do not allow others in the lift area
while operating the Scissor Lift. Do not allow anyone to ride on the Scissor Lift
while it is being raised or lowered.
17.
When lifting a vehicle raise the Rubber Saddles (39B) slowly until the
Rubber Saddles securely contact the vehicle manufacturer’s recommended
lifting points. Then, lift the vehicle to the desired working height. ALWAYS lift
the vehicle high enough for the Safety Lock Assembly (36B) to operate properly.
18.
Do not use the Scissor Lift as a permanent stand for a vehicle. Use the
Scissor Lift only while making repairs. Then, immediately remove the vehicle
from the Scissor Lift.
19.
Before lowering the Scissor Lift, make sure tool trays, stands, and all other
tools and equipment are removed from under the vehicle.
20.
Make sure to squeeze and hold in on the Brake Lever (13B) before
attempting to lower the vehicle. Do not release pressure on the Brake Lever
until the Scissor Lift is completely lowered.
21.
Before removing a vehicle from the Scissor Lift make sure the Plates (42B)
and Rubber Saddles (39B) are moved inward to provide an unobstructed
exit.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 22.
People with pacemakers should consult their physician(s) before use.
Electromagnetic fields in close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
23.
This product contains or produces a chemical known to the State of California to
cause cancer and birth defects (or other reproductive harm). (California Health &
Safety Code § 25249.5, et seq.)
ASSEMBLY INSTRUCTIONS
Note: For additional references to the parts listed in the following pages, refer to the
Assembly Diagrams on pages 17, 18, and 19.
Determine The Proper Scissor Lift Location:
1.
Do not use the Scissor Lift on any asphalt surface. Make sure the Scissor
Lift is used on a dry, oil/grease free, flat, level, CONCRETE surface capable
of supporting the weight of the Scissor Lift, the vehicle being lifted, and any
additional tools and equipment. The concrete floor surface should have a
minimum thickness of 5”. The concrete must have a minimum strength of 4,000
PSI, and should be aged at least 30 days prior to use. Do not use the Scissor
Lift on concrete expansion seams or on cracked, defective concrete.
2.
Make sure to check the desired location for possible obstructions such as a low
ceiling, overhead lines, adequate working area, access ways, exits, etcetera.
3.
Make sure to allow a minimum space of 14 feet in front and behind the Scissor
Lift to accommodate all vehicles. Certain allowances should be made for special
vehicle requirements or unusual floor plans.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page To Attach The Hydraulic Pump To The Scissor Lift:
HYDRAULIC PUMP - SIDE VIEW
MOTOR
(1A)
POWER
SWITCH
POWER CORD
HYDRAULIC OIL DELIVERY PORT
PRESSURE RELIEF
VALVE HANDLE
(3A)
OIL TANK FILL CAP
OIL TANK
(13A)
DOLLY ARM
HANDLE
(11B)
BOLT (14B)
BRAKE LEVER ASS’Y.
(13B)
OIL PIPE CONNECTOR
(17B)
BRAKE STEEL CABLE
(10B)
GENERAL INLET PIPE
(18B)
FIGURE D
1.
Locate the Hydraulic Pump unit (1A through 15A) in an area where it will be out
of the way, is safe from damage and weather, and where it can be easily reached
to operate. (See Figure D.)
2.
One end of the General Inlet Pipe (18B) has been pre-attached to the Scissor
Lift by the manufacturer. To attach the remaining end of the General Inlet Pipe to
the Hydraulic Pump wrap the male threads of the Oil Pipe Connector (17B) with
about 4” of pipe thread seal tape (not included). Remove the Oil Filler Nut Cap
(4A) from the threaded Hydraulic Oil Delivery Port. Then, wrench tighten the Oil
Pipe Connector into the Hydraulic Oil Delivery Port. (See Figure D.)
3.
One end of the Brake Steel Cable (10B) has been pre-attached to the Scissor
Lift by the manufacturer. The Brake Lever Assembly (13B) is located on the
remaining end of the Brake Steel Cable, and must be attached to the Handle
(11B) of the Dolly. To do so, slide the Brake Lever Assembly onto the Handle.
Then, secure the Brake Lever Assembly to the Handle by tightening the Bolt
(14B). (See Figure D.)
SKU 91315
For technical questions, please call 1-800-444-3353.
Page To Fill The Oil Tank With Hydraulic Oil:
The hydraulic Oil Tank (13A) has a holding capacity of 6.5 quarts. To fill the Oil
Tank, squeeze and hold the Brake Lever (13B) to release any load on the Scissor
Lift. Remove the Oil Tank Fill Cap on the Oil Tank. Add a premium quality
hydraulic oil until the level of the oil is even with the Oil Tank’s fill hole. Then,
replace the Oil Tank Fill Cap. (See Figure D.) Before the first use and before
all subsequent uses, check the hydraulic oil tank to make sure the Oil Tank is
properly filled.
OPERATING INSTRUCTIONS
Check The Safety Lock Assembly:
PLATE
(42B)
RUBBER SADDLE
(39B)
SAFETY LOCK ASSEMBLY
(1C THROUGH 11C)
GENERAL INLET PIPE
(18B)
FIGURE E
BRAKE STEEL CABLE
(10B)
1.
WARNING! Never operate the Scissor Lift if the Safety Lock Assembly
(1C through 11C) is not working properly. (See Figure E.)
2.
Insert the Power Plug (not included) of the Lift into a properly grounded, 3-hole,
220 volt electrical receptacle, and allow several seconds for the Motor (1A) to
warm up. (See Figure D.)
3.
Squeeze and release the Brake Lever (13B) several times and, while doing so,
observe that the Safety Lock Assembly (1C through 11C) operates properly in
REV 07j
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 10
response to the Brake Lever. Then, release pressure on the Brake Lever.
(See Figures D and E.)
4.
Press on the Power Switch and hold, and observe that the Safety Lock Assembly
(1C through 11C) “clicks” into place as the Scissor Lift rises. NOTE: There are
safety catches on the Safety Lock Assembly as the Scissor Lift rises. Once the
Safety Lock Assembly locks into each of these safety catches, you must squeeze
and hold in on the Brake Lever (13B) to lower the Scissor Lift.
(See Figures D and E.)
5.
Once the Scissor Lift is fully elevated, release pressure on the Power Switch.
(See Figure D.)
6.
Without squeezing the Brake Lever (13B), press in on the Pressure Relief Valve
Handle (3A) and hold. Observe that the Scissor Lift will not lower, as the Safety
Lock Assembly (1C through 11C) is engaged. CAUTION! If the Safety Lock
Assembly does not engage, fully lower the Scissor Lift and have a qualified
service technician immediately repair the Safety Lock Assembly.
(See Figures D and E.)
7.
Should the Safety Lock Assembly (1C through 11C) not operate as described
in Step #6, raise the Scissor Lift slightly to take pressure off the safety catches.
Then, while squeezing the Brake Lever (13B) lower the Scissor Lift fully to the
floor.
Note: When working properly, you must BOTH squeeze in and hold the Brake Lever
and press in and hold the Pressure Relief Valve Handle (3A) to lower the Scissor
Lift. (See Figure D.)
To Position, Lift, And Lower A Vehicle On The Scissor Lift:
1.
Before driving a vehicle onto the Scissor Lift make sure that the Lift is fully
lowered, and position the Plates (42B) and Rubber Saddles (39B) inward.
(See Figure E.)
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 11
UNDERNEATH
VEHICLE
DRIVE-ON
DIRECTION
OF VEHICLE
DIMENSIONAL
CENTER OF
VEHICLE
CENTER
OF
GRAVITY
VEHICLE
ENGINE
FIGURE F
2.
Drive the vehicle over the Scissor Lift while keeping the vehicle parallel with
the Lift and aligning the center of gravity of the vehicle with the center of the
Lift. NOTE: The “Center of Gravity” (COG) of the vehicle is the balance point at
which there is equal weight in front of and behind the COG, and equal weight on
both sides of the COG. The COG is not necessarily the dimensional center of
the vehicle, but is often slightly toward the engine from the dimensional center of
the vehicle. (See Figure F.)
3.
Turn off the vehicle’s engine and engage the parking brake of the vehicle.
4.
Read the vehicle owner’s manual to identify the recommended vehicle lifting
points.
5.
Move the Plates (42B) outward, and position the Rubber Saddles (39B) to
contact the vehicle lifting points. (See Figures E and F.)
6.
WARNING! Do not lift the vehicle if you cannot establish secure and level
lifting points. Do not use substandard shims or other devices in place of
approved and recommended Rubber Saddle (39B) adapters. Never use the
Scissor Lift without the Rubber Saddles in place on each Plate (42B) and in
contact with the lifting points of the vehicle. (See Figure E.)
7.
Once the Rubber Saddles (39B) have been positioned under the vehicle lifting
points, operate the Power Switch to lift the vehicle slightly, and test to make sure
the vehicle is well balanced and the contact between the Rubber Saddles and
vehicle lifting points are secure. Then, proceed to lift the vehicle to the desired
height. (See Figure E.)
8.
NOTE: When the vehicle has been lifted to the desired height, and the Safety
Lock Assembly (1C through 11C) has locked in place, make sure to install proper
safety jack stands (not included), under the vehicle once it is lifted to the desired
height, as an additional safety measure.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 12
9.
Once the repair work to the vehicle is completed make sure to remove all tools,
safety jack stands, and materials from under the vehicle and Scissor Lift. Also,
make sure the work area is clear and it is safe to lower the vehicle.
10.
To lower the Scissor Lift, use the Power Switch and raise the vehicle slightly
to take weight off the Safety Lock Assembly (1C through 11C). Then, release
pressure on the Power Switch. (See Figure D.)
11.
Stand well away from the Scissor Lift and vehicle. Then squeeze and hold in the
Brake Lever (13B) while at the same time pushing in and holding the Pressure
Release Valve Handle (3A) to slowly lower the Scissor Lift all the way down to
the floor. (See Figure D.)
12.
Move the Rubber Saddles (39B) and Plates (42B) inward, out of the path of the
vehicle. (See Figure E.)
13.
Disengage the vehicle parking brake. Start the vehicle’s engine, and drive the
vehicle off the Scissor Lift slowly and carefully.
INSPECTION, MAINTENANCE, AND CLEANING
WARNING! Always unplug the Power Cord from its electrical outlet before
performing any inspection, adjustments, maintenance, or cleaning.
1.
Before each use, inspect the general condition of the Scissor Lift. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring and hoses, and any other condition that may affect its
safe operation. If abnormal noise or vibration occurs, have the problem corrected
before further use.
Do not use damaged equipment.
2.
Daily: With compressed air or a vacuum, remove all dirt and debris from the
Scissor Lift. Also, use a detergent or mild solvent to remove oil and grease from
the unit. Then, use a premium quality, machine oil to lubricate all moving parts.
3.
Daily: Check the level of hydraulic oil in the Oil Tank. The Oil Tank (13A) has a
holding capacity of 6.5 quarts. To fill the Oil Tank, squeeze and hold the Brake
Lever (13B) to release any load on the Scissor Lift. Remove the Oil Tank Fill Cap
on the Oil Tank. Add a premium quality hydraulic oil until the level of oil is even
with the Oil Tank’s fill hole. Then, replace the Oil Tank Fill Cap. (See Figure D.)
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 13
PARTS LIST/ASSEMBLY DIAGRAM A
Part
1A
2A
3A
4A
5A
6A
7A
8A
Description
Motor
Nut (M20 x 1.5)
Pressure Relief Valve Handle
Oil Fill Cap
Release Valve Assy.
Check Valve Assy.
9 Gear Bearing Cap
Safety Valve Nut Cap
Qty.
1
1
1
1
1
1
1
1
Part
9A
10A
11A
12A
13A
14A
15A
Description
Safety Valve Assy.
Valve Seat
Gear Pump
Bolt
Oil Tank
Bolt
Bumper Assy.
Qty.
1
1
1
2
1
4
1
1A
6A
2A
3A
7A
5A
4A
9A
10A
11A
8A
15A
12A
13A
14A
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 14
PARTS LIST/ASSEMBLY DIAGRAM B
Part #
1B
2B
3B
4B
5B
6B
7B
8B
9B
10B
11B
12B
13B
14B
15B
16B
17B
18B
19B
20B
21B
22B
Description
Part #
Qty.
Table
Retaining Ring (18)
Locking Nut (M20)
Oil Pipe Connector (3)
Branch Inlet Pipe
Oil Pipe Connector (2)
Oil Supply Fitting
Nut (M8)
Washer (8)
Brake Steel Cable
Handle
Hex Screw (M8)
Brake Lever Assy.
Bolt (M8)
Transmission Holder
Rubber Cap
Oil Pipe Connector (1)
General Inlet Pipe
Check Valve
Safety Locking Pin
Retaining Ring (20)
Cylinder Pin
1
8
1
3
2
2
1
4
4
4
1
4
1
4
1
3
1
1
2
1
20
2
23B
24B
25B
26B
27B
28B
29B
30B
31B
32B
35B
36B
37B
38B
39B
40B
41B
42B
43B
44B
45B
46B
Description
Scissor Pin
Outer Scissor
Inner Scissor
Wheel Pin
Large Wheel
Small Wheel
Wheel Pin
Connecting Pin
Cylinder Pin
Safety Locking Pin
Cylinder Assy.
Safety Lock Assy.
Retaining Ring (24)
Saddle Holder
Rubber Saddle
Locking Nut
Washer (20)
Plate
Bolt (M8 x 20)
Ring (15)
Wheel
Nut
Qty.
2
1
1
2
2
2
2
2
2
1
2
1
2
4
4
4
4
4
4
2
2
2
1B
42B
2B
41B
43B
40B
39B
16B
12B
11B
10B
6B
6B
8B
9B
13B
14B
15B
16B
45B
46B
7B
5B 4B
38B
3B
32B
37B
30B
31B
44B
29B
28B
35B
36B
17B
18B
19B
20B21B 22B
23B
24B 25B
27B
26B
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
REV 01/07
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 15
PARTS LIST/ ASSEMBLY DIAGRAM C
Part #
1C
2C
3C
4C
5C
6C
7C
8C
9C
10C
11C
12C
12C
9C
11C
10C
Description
Pin
Spring
Lock Block
Lock Pole
Lock Wheel
Nut M (8)
Bolt (M8)
Steel Wire Cable
Lock Sheath
Washer (12)
Bolt (M12)
Check Valve
1C
8C
7C
Qty.
1
1
1
3
1
1
1
1
1
1
1
1
4C
2C
3C
6C
5C
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF
ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 16
Limited 1 year / 90 day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that for a
period of one year from date of purchase that the tank is free of defects in materials and
workmanship (90 days if used by a professional contractor or if used as rental equipment).
Harbor Freight Tools also warrants to the original purchaser, for a period of ninety days
from date of purchase, that all other parts and components of the product are free from
defects in materials and workmanship. This warranty does not apply to damage due
directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations
outside our facilities, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. This warranty is expressly in lieu of all
other warranties, express or implied, including the warranties of
merchantability and fitness.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
REV 07j
SKU 91315
For technical questions, please call 1-800-444-3353.
Page 17
Download PDF

advertising