Specifications | Century 212 Automobile Accessories User Manual

INSTRUCTIONS
with 433MHz Radio Controls
QLD Office:
17 Oasis Court
Clontarf 4019
SA Office:
(07) 3883-0200
NSW Office:
34-36 Marigold Street
Revesby 2212
(02) 9722 5555
23 Frederick Road
Royal Park 5014
(08) 8447 4747
WA Office:
96 Mulgul Road
Malaga 6090
(08) 9247 8777
VIC/TAS Office: 147-153 Canterbury Road
Kilsyth 3137
C-Tick approval logo
min. size 3mm diam.;
letters min. 3mm high
(03) 9237 7766
B&D Doors
New Zealand:
70 Allens Road
EastTamaki
Auckland, New Zealand
(09) 273 8600
www.bnd.co.nz
The Controll-A-Door-P has
been tested and complies
with the standards:
AS/NZS 3350.2.95:2000
(incl. Amdt1) & AS/NZS
CISPR 14.1:2003
N1134
TABLE OF CONTENTS
Introduction
Adjustment Section
2-7
Adjust the travel limits ...............................................25
Adjust the force .........................................................26
Test the safety reverse system .................................27
Testing the safety infra-red safety sensors ...............27
Safety rule review........................................................2
Preparing your garage door ........................................3
Tools needed ...............................................................3
Planning ..................................................................4-5
Carton inventory ..........................................................6
Hardware inventory .....................................................7
Assembly
Operation
28-30
Operation safety instructions.....................................28
Using your garage door opener ................................28
To open the door manually........................................29
Care of your opener ..................................................29
Troubleshooting.........................................................30
8-10
Assemble the rail & attach the chain pulley bracket ...8
Install the trolley ..........................................................9
Fasten rail to motor unit ..............................................9
Install chain & attach chain spreader.....................9-10
Install the chain noise reduction pads.......................10
Installation
25-27
Programming
31
To code a hand-held remote control .........................31
To erase all codes .....................................................31
Multi-function remotes ...............................................31
11-24
Installation safety instructions....................................11
Determine the header bracket location................12-13
Install the header bracket..........................................14
Attach the rail to the header bracket.........................15
Position the opener ..............................................15-16
Hang the opener ..................................................16-17
Install the door control...............................................17
Install the remote control wall mount (optional) ........17
Wiring instructions for optional accessories..............18
Install the light globe .................................................19
Attach the emergency release rope and handle .......19
Connect electric power..............................................19
Installing the safety infra-red safety sensors.............20
Fasten the door bracket .......................................21-22
Connect door arm to trolley .................................23-24
Warranty
32
INTRODUCTION
Safety Rule Review
This garage door opener is designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the warnings, safety instructions and instructions contained in
this manual.
When you see these Safety Symbols and Signal
Words on the following pages, they will alert you to
the possibility of serious injury or death if you do
not comply with the corresponding instructions. The
hazard may come from something mechanical or
from electric shock. Read the instructions carefully.
WARN
ARNING
ING
WARN
ARNING
ING
Mechanical
CAUTION
WARN
ARNING
ING
WARN
ARNING
ING
WARN
ARNING
ING
WARN
ARNING
ING
Electrical
When you see this Signal Word on the following
pages it will alert you to the possibility of damage to
your garage door and/or the garage door opener if
you do not comply with the corresponding
instructions. Read them carefully.
WARN
ARNING
ING
CAUTION
114A2845
WARN
ARNING
ING
2
Preparing your garage door
WARN
ARNING
ING
• Disable locks. Insert wood screws or nails to keep
them unlocked.
• Remove any ropes connected to garage door.
To prevent possible SERIOUS INJURY OR DEATH:
• Always call for professional B&D garage door service if
garage door binds, sticks, or is out of balance. An
unbalanced garage door might not reverse when
required.
• NEVER try to loosen, move, or adjust garage door,
door springs, cables, pulleys, brackets or their
hardware, all of which are under EXTREME tension.
• Disable ALL locks and remove all ropes connected to
garage door before installing and operating garage
door opener to avoid entanglement.
• This unit should not be installed in a damp or wet space.
• The door must not extend over public byway during
operation.
• This product is provided with a power supply cord of
special design which, if damaged, must be replaced by
a power supply cord of the same type; such a power
supply cord may be obtained from you local B&D
distributor and must be fitted by a specialist.
• This unit is supplied as a plug-in-device and it is
strongly advised that this unit remain a plug-in device.
Any alterations or changes to this will result in the
opener warranty being void.
CAUTION
TESTING YOUR DOOR
Before you begin, complete the following test to
make sure your door is balanced and is not sticking
or binding:
• Lift the door about halfway as shown. Release the
door. It should stay in place, supported entirely by
its springs.
• Raise and lower the door to see if there is any
binding or sticking.
If your door binds, sticks, or is out of balance, call for
professional garage door service.
WARN
ARNING
ING
CAUTION
To avoid damage to the garage door and opener, disable
locks before installing and operating the opener. Use a
wood screw or nail to hold locks in the "open"
(unlocked) position.
Operation at other than 230V/50 Hz will cause opener
malfunction and damage.
ONE-PIECE DOOR
SECTIONAL DOOR
Sectional Door
Tools needed
During assembly, installation and adjustment of the
opener, instructions will call for hand tools as
illustrated.
ONE-PIECE DOOR
SECTIONAL DOOR
One-Piece Door
PORTE ARTICULÉE
PORTE RIGIDE
Carpenter's
Level
Pencil
1
2
Hack Saw
Tape Measure
Wire Cutters
Claw Hammer
Drill
PORTE ARTICULÉE
114A2845
Stepladder
PORTE RIGIDE
8mm, 5mm, and
4mm Drill Bits
13mm, 11mm, and 6mm
Sockets and Wrench
3
Pliers
Locking pliers
Screwdriver
Adjustable End Wrench
Planning
• Do you have an access door in addition to the
garage door? If not, Model T7012 Emergency
Access Device is required.
Identify the type and height of your garage door.
Survey your garage area to see if any of the
conditions below apply to your installation. Additional
materials may be required. You may find it helpful to
refer back to this page and the accompanying
illustrations as you proceed with the installation of
your opener.
Depending on your requirements, there are several
installation steps which may call for materials and/or
hardware not included in the carton.
• Installation Step 1 – Look at the wall or ceiling
above the garage door. The header bracket must
be securely fastened to structural supports.
• Installation Step 5 – Do you have a finished ceiling
in your garage? If so, a support bracket and
additional fastening hardware may be required.
B&D recommends the use of safety infrared
reversing sensors on all installations of
automatic garage door openers.
and vertical reinforcement
• Installation Step 10:Horizontal
is needed for lightweight garage doors
– Depending upon (fiberglass,
garage steel,
construction,
extension
aluminum, door
with
panels,
etc.). be needed to
brackets or woodglass
blocks
may
See page 21 for details.
install the infrared safety sensors.
– Alternate floor mounting of theHeader
infrared
safety
Wall
sensors will require hardware not provided.
SECTIONAL DOOR INSTALLATIONS
• Do you have a steel, aluminum, fibreglass or glass
panel door? If so, horizontal and vertical reinforcement is required (Installation Step 11).
• The opener is normally installed at the centre of
the door. If there is a torsion spring or centre
bearing plate in the way of the header bracket or
door bracket area, the opener may be installed
within 300mm to the left or right of the door centre.
See Installation Steps 1 and 11.
• Look at the garage door where it meets the floor. It
must close on the floor all the way across.
Otherwise, the safety reverse system may not work
properly. See Adjustment Step 3. Floor or door
should be repaired.
OPENER
ARM MOUNTING LOCATION
FINISHED CEILING
Supportbe
bracket
&
Must
mounted
on a stile. Add an additional stile if
fastening hardware
required
or
offset
mount
the opener (see below and
is required.
See page
page
5).17.Attach arm 1/3 panel height from top at 10O
as shown.
Motor Unit
Sectional Door Installation
FINISHED CEILING
Header Wall
Support bracket &
fastening hardware
is required.
See page 17.
Extension Spring
Excess MUST
be removed
OR
Torsion Spring
———
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fibreglass, steel, aluminum, door with
glass panels, etc.).
See page 21 for details.
Door
Center
Access
Door
Excess MUST
be removed
Motor Unit
———
10o
10o
Safety
Reversing
Sensor
Extension Spring
———
Centre Stile
optimum Safety Reversing Sensor
Door
location for
Centre
attachment
Gap between floor and bottom of OR
door must not exceed 6mm.Torsion Spring
Access
Door
1/3
Re-enforcement
Must be attached below
Panel Re-enforcement
if used.
Re-enforcement
———
CLOSED POSITION
Header
Bracket
——
Safety
Reversing
Sensor
Header
Sleeve Bracket
Trolley
Rail Assembly
Garage
Door
Spring
Emergency
Release
Rope & Handle
Gap between floor and bottom of
door must not exceed 6mm.
Straight
Door
Arm
Safety Reversing Sensor
Header
Wall
114A2845
Panel Height
——
1/3
Panel Height
10o
4
Header Header Door
Garage
Bracket
Bracket
Sleeve Bracket
Door
Trolley
Curved
Door
Arm
CLOSED POSITION
Rail Assembly
OFF CENTRE INSTALLATION OF OPENER
In situations where obstruction prevent mounting the
opener centrally, offsetting the opener attachment is
possible within the following range - 1/4 Door width
from centre.
NOTE: Even though it is acceptable practise to off
centre mount the opener, the further off centre the
opener is mounted the more dependent is the door
operation on a good installation. This relates to
correct set-up of opener and track, and correct door
balance.
The installation of the IR Safety Sensor is
recommended for an off centre mount application.
1/4 Door
Width
1/4 Door
W
idth
ONE-PIECE DOOR INSTALLATIONS
• Generally, a one-piece door does not require
reinforcement. If your door is lightweight, youFINISHED
can CEILING
e Chamberlain
Group, Inc.
Support bracket
refer to the information relating to sectional doors
e-Piece Doorinwith
TrackStep
Installation
(Cable -USA)& fastening
Installation
11.
hardware is required.One-Piece Door without Track
3/93Chamberlain
The
Group,
on Inc.
your door’sHeader
construction, you See
maypage 17.
• Depending
FINISHED CEILING
Wall
need
additional
mounting
hardware
for
the
door
One-Piece Door with Track Installation (Cable -USA)
Support bracket & fastening
hardware is required. See page 17.
bracket (Step 11).
/3/93
Header
• The gap between the bottom of the garage door
Wall
and the floor cannot exceed 6mm. Otherwise, the
safety reverse system may not work properly. See
Adjustment Step 3. The floor or the door should be
repaired.
Access Door
One-Piece Door with Track
Access Door
Access
Door
Access
Gap between floor
and bottom
Door
of door must not
exceed 6mm.
Safety
Reversing
Sensor
Safety Reversing Sensor
Gap between floor and bottom
of door must not exceed 6mm.
Safety
Reversing
Sensor
Safety Reversing Sensor
Safety
Reversing Sensor
Safety
Reversing Sensor
Gap between floor
and bottom of door
must not exceed 6mm.
Safety
Reversing Sensor
CLOSED POSITION
Safety
Reversing Sensor
Gap between floor
and bottom of door
must not exceed 6mm.
Header
Sleeve Bracket
Header
Bracket
CLOSED POSITION
Header
Wall
Header
Wall
Garage
Door
Garage
Door
114A2845
Header Sleeve Bracket
Trolley
Header
Door
Bracket
Bracket
Curved
Straight
Door
Arm
Door
Arm
Straight
Door
Bracket Door
Arm
Header
Wall
5
Garage
Door
Header
Sleeve Br
Header
Bracket
Emergency
Release
Rope &
Handle
Trolley
Rail
Emergency
Release
Rope & Handle
Rail
Emergency
Release
Rope & Handle
Chain
Rail
Door Bracket
CLOSED POSITION
Header Curved
Sleeve Bracket
Header
Bracket Door Arm
Trolley
Straight
Door
Arm
Door Bra
Curved
Door
Arm
Header
Wall
Gara
Door
Carton Inventory
Hardware for assembly and installation is shown on
the next page. Save the carton and packing material
until installation and adjustment is complete.
Your garage door opener is packaged in two cartons
which contains the motor unit and the parts illustrated
below. If anything is missing, carefully check the
packing material. Parts may be stuck in the foam.
Remote Control
Transmitter Visor Clip
1-Function Remote
Control Transmitter (1)
Remote Control
Wall Mount Bracket
3-Function Mini Remote
Control Transmitter (1)
Light Lens (1)
Illuminated
Push Button
Chain Spreader with Screws
and Washers
Trolley
Inner Trolley
Chain
1-Piece Rail
Bell Wire
4-Piece Rail
Header Sleeve Bracket
Rail
Centre
Section
Light globe
Vibration Isolators
Hanging Brackets
Header Bracket
Door Bracket
Rail Straps
Safety Labels
and
Literature
Chain Noise
Reduction Pads
114A2845
6
Curved Door
Arm Section
Straight Door
Arm Section
Hardware Inventory
Separate all hardware and group as shown below for the assembly and installation procedures.
ASSEMBLY
Washered Screw 25mm (4)
(mounted in opener)
Spring /Trolley Nut (1)
Screw (2)
Master
Link (2)
Carriage bolt (1)
INSTALLATION
Hex Screw
8mm x 20mm (4)
Nut
8mm (7)
Lock Washer
8mm (7)
Ring Fastener (4)
Lag Screw
8mm x 40mm (4)
Insulated
Staples
Rail Grease
Rope
Anchors
8mm x 40mm (6)
Sheet Metal Screw
8mm x 13mm (2)
NOTIC
E
Lag Screw
8mm x 45mm (2)
Screw
6AB x 25mm (2)
Carriage Bolt
8mm x 65mm (2)
Clevis Pin
8mm x 13mm (2)
114A2845
Handle
Dry Wall Anchors (2)
Clevis Pin
8mm x 25mm (2)
7
Stop Bolt (1)
Clevis Pin
8mm x 32mm (1)
HARDWARE SHOWN ACTUAL SIZE
ASSEMBLY STEP 1
Assemble the Rail
NOTE: If your opener came with a one piece rail,
proceed to Assembly step 2, page 9.
Grease inside edges of rail brace sections. Place rail
pieces on flat surface for assembly. All four rail
sections are interchangeable. Slide rail braces onto
rail section. Connect rail by sliding rail brace onto
next rail section. Tap rail assembly on piece of wood
until rail sections are flush. Repeat with remaining
rail sections.
Spring Trolley Nut
Carriage Bolt
Install the Chain
RAIL ASSEMBLY
Remove chain from carton and lay chain out on floor
(do not allow chain to twist). Push pins of master link
bar through chain link and hole in back end of trolley.
Push cap over pins and onto notches. Slide clip-on
spring over cap and onto pin notches until both pins
are securely locked in place.
Rail Piece
Insert Chain into Rail & Assemble
Header Sleeve
Rail Brace
Slide pulley bracket and inner trolley into back
(opener end) of rail assembly, be sure to insert pulley
bracket as shown with arrow pointing toward front
(header end) of rail. Push bracket toward front
(header end) of rail. Insert carriage bolt through
header sleeve bracket. Loosely thread spring nut
onto carriage bolt. Insert carriage bolt of header
sleeve assembly into bold cut out in pulley bracket.
Slide header sleeve assembly on to front (header
end) of rail.
Rail
Piece
Grease
Rail assembly
INSTALLING THE CHAIN
Back End of Trolley
Spring
Cap
Chain Link
Piece of Wood
Master Link Bar
Front (Header End)
of Rail
Carriage Bolt
Header Sleeve
Bracket
Back
(Opener End)
of Rail
Assembly
Spring Nut
Header Sleeve
Bracket
Ar
ro
w
Carriage Bolt
Pulley
Bracket
Pulley
Bracket
114A2845
Inner
Trolley
8
ASSEMBLY STEP 2
Attach Trolley to Rail
Slide outer trolley into rail assembly, be sure arrow
on trolley is heading in direction of door is heading in
direction of door. Slide outer trolley down rail until it
engages with inner trolley.
Arrow
Rail Assembly
WARN
ARNING
ING
Outer Trolley
Arrow
CAUTION
To avoid serious damage to opener, ONLY use screws
mounted in top of motor unit.
Towards Door
ASSEMBLY STEP 3
Attach Chain Spreader
AVERTISSEMENT
Phillips Pan Head Screws
Attach chain spreader to opener with phillips pan
head screws.
Chain Spreader
ATTENTION
WARN
ARNING
ING
WARN
ARNING
ING
Opener
To avoid possible SERIOUS INJURY to fingers from
moving garage door opener:
• ALWAYS keep hand clear of sprocket while operating
opener.
• Securely attach chain spreader before operating.
CAUTION
WARN
ARNING
ING
ASSEMBLY STEP 4
Fasten Rail to Opener & Install Chain
Remove four washered bolts from top of opener. Place
rail on opener, flush with stops on top of opener. Wrap
chain around slot in spreader and over sprocket. Push
idler pulley bracket assembly toward front of the rail to
eliminate excess slack in chain. Align bolt holes on
brackets with bolt holes on opener. Secure brackets to
opener with previously removed bolts . Tighten bolts
securely. The opener sprocket teeth must engage
the chain. Insert bolt into trolley stop bolt hole secure
with lock washer and nut.
CAUTION: Use only those bolts mounted in the
top of opener. Use of any other bolts will cause
serious damage to opener.
Set Chain Tension
Thread spring nut on carriage bolt unit finger tight.
Insert a screwdriver tip into one of the slots of the nut
ring and brace it firmly against the header sleeve.
Place an open end wrench on the square end of the
spring nut, slightly rotate nut about 1/4 turn clockwise
until nut ring is released against header sleeve. This
sets spring to optimum chain tension. chain may slip
off sprocket if chain is too loose. If chain does slip retighten spring nut by turing nut clockwise 1/2 turn.
Do NOT overtighten chain.
114A2845
9
FASTEN RAIL TO OPENER
SET CHAIN TENSION
Spreader
Stops
HARDWARE SHOWN
ACTUAL SIZE
Spring /Trolley Nut
Washered Bolt
Stops
Spreader
Sprocket
Sprocket
Nut Ring
Screwdriver
Tip
Wrench
Bolt
2
4
Trolley Stop
Bolt Hole
Spring Nut
Lock
Washer
Nut
Header Sleeve
Lock Washer
Bolt
Trolley
Square
End
Square
End
Nut Ring
BEFORE
25mm
Nut
Trolley
Nut Ring
AFTER RELEASE
32mm
Screwdriver Tip
ASSEMBLY STEP 5
Nut Ring
Install
Chain Noise Reduction Pads
(optional)
Wrench
114mm
Spring Nut
114mm
Header Sleeve
1. Clean and remove grease from
rail in areas where pads will be
installed.
114A2845
2. With chain tensioned, lift up the
chain and place noise reduction
pads under the chain in orientation
shown.
10
3. Install with adhesive side down
allowing pad to stick to rail.
INSTALLATION
NING
WARN
ARNING
INGINSTRUCTIONS
IMPORTANT INSTALLATION
ION
WARN
ARNING
ING
To reduce the risk of severe injury or death:
1. READ AND FOLLOW ALL INSTALLATION
WARNINGS AND INSTRUCTIONS.
2. Install garage door opener only on properly
balanced and lubricated garage door. An
improperly balanced door may not reverse when
required and could result in severe injury or
death.
3. All repairs to cables, spring assemblies and other
hardware MUST be made by a trained door
systems technician before installing opener.
4. Disable all locks and remove all ropes connected
to garage door before installing opener to avoid
entanglement.
5. Install garage door opener 2.1m or more above
floor.
6. Mount emergency release handle 1.8m feet above
floor.
7. NEVER connect garage door opener to power
source until instructed to do so.
114A2845
8. NEVER wear watches, rings or loose clothing
while installing or servicing opener. They could
be caught in garage door or opener
mechanisms.
9. Install wall-mounted garage door control:
• within sight of the garage door
• out of reach of children at minimum height
of 1.5m
• away from all moving parts of the door.
10. Place entrapment warning label on wall next to
garage door control.
11. Place manual release/safety reverse test label in
plain view on inside of garage door.
12. Upon completion of installation, test safety
reversal system. Door MUST reverse on contact
with a 40mm high object on the floor.
11
INSTALLATION STEP 1
Finished
Ceiling
Vertical
Centreline
Determine the Header Bracket
Location
40mm
Reinforcement
Board
Structural
Supports
Header
Wall
Installation procedures vary according to garage door
types. Follow the instructions which apply to your
door.
SECTIONAL DOOR A
ONE-PIECE DOOR WITH
WARN
ARNING
ING
WARN
ARNING
ING
To prevent possible SERIOUS INJURY or DEATH:
• Header bracket MUST be RIGIDLY fastened to
structural support on header wall or ceiling, otherwise
garage door might not reverse when required. DO NOT
install header bracket over drywall.
• Concrete anchors MUST be used if mounting header
bracket or 40mm reinforcement board into masonry.
• NEVER try to loosen, move or adjust garage door,
springs, cables, pulleys, brackets, or their hardware, all
of which are under EXTREME tension.
• ALWAYS call a trained door systems technician if
garage door binds, sticks, or is out of balance. An
unbalanced garage door might not reverse when
required.
Vertical
Centreline
CAUTION
WARN
ARNING
ING
Ceiling
SECTIONAL DOOR
AND ONE-PIECE DOOR WITH TRACK
1. Close the door and mark the inside vertical
centreline of the garage door.
2. Extend the line onto the header wall above the
door.
NOTE: You can fasten the header bracket within
300mm of the left or right of the door center only if a
torsion spring or centre bearing plate is in the way; or
you can attach it to the ceiling (see page 14) when
clearance is minimal. (It may be mounted on the wall
upside down if necessary, to gain approximately
12mm.)
If you need to install the header bracket on a 40mm
reinforcement board (on wall or ceiling), use lag
screws (not provided) to securely fasten the 40mm
reinforcement board to structural supports as shown
here and on page 13. If installing into masonry, use
concrete anchors.
3. Open your door to the highest point of travel as
shown. Draw an intersecting horizontal line on the
header wall 50mm above the high point. This
height will provide travel clearance for the top edge
of the door.
Header Wall
50mm
114A2845
Header Wall
50mm
Highest Point
of Travel
Sectional door
with curved
Door
track
Trac
Highest Point
of Travel
Door
Sectional
door with curved track
Ceiling
One-piece door with horizontal
Header Wall
50mm
Track
Header Wall
50mm
Highest Point
of Travel
Door
Proceed to Step 2, page 14.
Track
One-piece
door with
horizontal
track
Sectional door with curved track
12
Track
Highest Point
of Travel
Door
One-piece door with horizontal track
One Piece Door Without Track
1/30/92 - 4/7/92
ONE-PIECE DOOR WITHOUT TRACK
Unfinished
1. Close the door and mark the inside vertical
Ceiling
40mm
centreline of your garage door. Extend the line
Reinforcement
onto the header wall above door, as shown.
Board
Header
Vertical
Wall
If headroom clearance is minimal, you can install
Centreline
the header bracket on the ceiling. See page 14.
If you need to install the header bracket on a
40mm reinforcement board (on wall or ceiling),
Theuse
Chamberlain Group, Inc.
lag screws (not provided) to securely fasten the
Position Header Bracket
40mm reinforcement board to structural supports
Doors Without Track
as shown. If installing into masonry, use concrete
anchors (not provided).
1/30/92 - 4/7/92
Vertical
2. Open your door to the highest point of travel as
Centreline
of Garage
shown. Measure the distance from the top of the
Door
door to the floor. Subtract the actual height of the
door. Add 200mm to the remainder.
(See Example).
3. Close the door and draw an intersecting horizontal
line on the header wall at the determined height.
If the total number of millimeters exceeds the
height available in your garage, use the
maximum height possible, or refer to page 14
for ceiling installation.
Header Wall
40mm
Reinforcement
Board
OPTIONAL
CEILING MOUNT
FOR
HEADER BRACKET
Highest Po
of Travel
Highest Point
of Travel
Header Wall
Inc.
Distance
Door
Door
Distance
EXAMPLE
Distance from top of door
Chamberlain
Group,
(at highest point of travel)The
to floor
................ 2300mm
Position Header Bracket
Actual height of door....................................-2100mm
Doors Without Track
Remainder....................................................
200mm
Add...............................................................
1/30/92 - 4/7/92+200mm
Bracket height on header wall ..................... =400mm
(Measure UP from top of CLOSED door.)
Structural
Supports
Jamb
Hardware
Pivot
Proceed to Step 2, page 14.
Floor
One-piece door without track:
jamb hardware
Header Wall
Highest Point
of Travel
Highest Point
of Travel
Header Wall
Distance
Door
Jamb
Hardware
Distance
Door
Pivot
Floor
114A2845
13
Floor
One-piece door without track:
pivot hardware
INSTALLATION STEP 2
Install the Header Bracket
Bracket Holes
WALL HEADER BRACKET INSTALLATION
Wall Mounting Holes
• Centre the bracket on the vertical guideline with the
bottom edge CEILING
of the
bracket
on the horizontal line
MOUNT
ONLY
The nail hole is for
(with the arrow pointing towardpositioning
the ceiling).
only.
You must use lag screws
UP
• Mark all of the bracket holes. Drill
4.5mm
(3/16")
to mount
the header
bracket.
pilot holes and fasten the bracket with wood
screws. For concrete mount, use concrete anchors
provided.
Optional
Wall Mounting Holes
HARDWARE SHOWN ACTUAL SIZE
Bracket Holes
Vertical
Center Line
Header
Wall
NLY
TO
G
MO
UN
ILIN
Lag Screw
8mm x 40mm
CE
UP
25mm
Board
Header
Bracket
Lag Screws
8mm x 40mm
25mm
Board
Lag Screws
8mm x 40mm
Header
Bracket
Door Spring
Anchors
8mm x 40mm
– Finished Ceiling –
CEILING HEADER BRACKET INSTALLATION
Highest Point of
Highest Point of
Garage Door Travel
Vertical
Garagevertical
Door Travel
• Extend
guideline onto the
ceiling.
Center Line
15cm Maximum
• Centre the bracket on the vertical mark no more
Door
than 150mm (6") from the wall. Make sure the
Spring
arrow is pointing toward
theMounting
wall. Holes
Ceiling
• Mark all of the bracket holes
Drill 4.5mm (3/16")
CEILING (5).
MOUNT ONLY
pilot holes and fasten the bracket with wood
screws. For concrete ceiling mount,
use concrete
UP
anchors
provided.
The nail hole is for
Garage Door
Header
Bracket
Vertical Centreline
UP
50mm
(2")
Garage
Door
positioning only.
You must use lag screws
to mount the header bracket.
Vertical
Centre Line
Header
Wall
Garage
Door
Lag Screws
8mm x 40mm
Vertical
Centre Line
Header Wall
Vertical
Centreline
– Finished Ceiling –
Bracket Holes
Header
Bracket
Vertical Centreline
150mm
(6")
Door
Spring
Lag Screws
8mm x 40mm
Bracket Holes
Header Wall
114A2845
14
INSTALLATION STEP 3
Attach the Rail to the Header Bracket
• Position opener on garage floor below the header bracket. Use packing material to protect the cover. Raise
rail until holes in the header sleeve and holes in the header bracket align. Join with clevis pins. Insert ring
fasteners to secure.
NOTE: To enable the rail to clear sectional door springs, it may be necessary to lift opener onto a temporary
support. The opener must either be secured to a support or held firmly in place by another person.
Header Wall
Header Bracket
Ring Fastener
Header
Sleeve
Bracket
Ring Fastener
Clevis Pin
8mm x 13mm
Clevis Pin
8mm x 13mm
Clevis PIn
8mm x 13mm (2)
Header Sleeve
Bracket
Rail
Garage Door
Ring fastener (2)
HARDWARE SHOWN
ACTUAL SIZE
Temporary Support
INSTALLATION STEP 4
Position the Opener
Follow instructions which apply to your door type as illustrated.
SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK
A 25 mm board laid flat is convenient for setting an ideal door-to-rail distance.
• Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough.
• Open the door all the way and place a 25mm board laid flat on the top section beneath the rail.
• If the top section or panel hits the trolley when you raise the door, pull down on the trolley release arm
to disconnect inner and outer sections. Slide the outer trolley toward the motor unit. The trolley can remain
disconnected until Installation Step 12 is completed.
WARN
ARNING
ING
CAUTION
ENGAGED
114A2845
To prevent damage to garage door, rest garage door
opener rail on 25mm board or equivalent placed on top
section of door.
Trolley
Release Arm
RELEASED
15
Rail
Door
25mm
Board laid flat
Door
ONE-PIECE DOOR WITHOUT TRACK
• With the door fully open and parallel to the floor,
measure the distance from the floor to the top of
the door.
• Using a stepladder as a support, raise the top of
the opener to this height.
• The top of the door should be level with the top of
the motor unit. Do not position the opener more
than 50mm above this point.
Rail
25mm
Board laid flat
Door
Header
Bracket
Top of Motor Unit
Top of door
Header
Bracket
WARN
ARNING
ING
Top of Motor Unit
Top of doorSERIOUS INJURY from a falling
To avoid possible
garage door opener, fasten it SECURELY to structural
supports of the garage. Concrete anchors MUST be used
if installing any brackets into masonry.
CAUTION
INSTALLATION STEP 5
Hang the Opener
The opener must be securely fastened to a
structural support of the garage.
Two representative installations are shown. Yours may
be different. Hanging brackets should be angled
(Figure 1) to provide rigid support. On finished ceilings,
(Figure 2) attach a sturdy metal bracket (not supplied)
to a structural support before installing the opener.
1. On each side of opener measure the distance from
the opener to the structural support (or ceiling).
2. Cut both pieces of the hanging bracket to required
lengths. Flatten one end of each bracket and bend
or twist to fit the fastening angles. Do not bend at
the bracket holes. Drill 4.5mm (3/16") pilot holes in
the structural supports (or ceiling). Attach flattened
ends of brackets to supports with wood screws.
3. Lift opener and fasten to hanging brackets with
screw, lock washer and nut. Check to make sure
rail is centered over the door.
4. Remove 25mm (1") board. Operate door manually.
If door hits the rail, raise header bracket.
5. Use rail grease and lubricate inside surface of rail.
Structural
FigureSupports
1
Structural
Supports
Lag Screws
8mm x 45mm
1
Lag Screws
8mm x 45mm
Figure 2
Hidden
Support
Hidden
Support
Bracket
(Not provided)
Lag Screws
8mm x 45mm
Lag Screws
8mm x 45mm
114A2845
Lock
Washer 8mm
Measure
Screw
8mm
Distance
Nut 8mm
FINISHED CEILING
Lag Screw
8mm x 45mm
Nut 8mm
Measure
Distance
Lock Washer 8mm
Screw 8mm
Nut 8mm
HARDWARE SHOWN ACTUAL SIZE
Hex Screw
8mm x 20mm
1
FINISHED CEILING
Bracket
(Not provided)
Lock Washer 8mm
Screw 8mm
Nut 8mm
Lock Washer 8mm
Screw 8mm
Nut 8mm
Lock Washer 8mm
16
INSTALLATION STEP 6
Lighted Door
Control Button
Terminal Screws
Install the door control
Bell Wire
WHT
-2
Locate the door control within sight of the door at a
minimum height of 1.5m where small children
cannot reach, and away from all moving parts of
the door and door hardware.
1. Strip 6mm of insulation from one end of the bell
wire. Connect it to the two screw terminals on the
back of the door control by color: white wire to 2
and white/red wire to 1.
2. Fasten the Lighted Door Control Button securely
with 6ABx1-1/2” screws. If installing into drywall,
drill 4mm holes and use the anchors provided.
3. Run the bell wire up the wall and across the
ceiling to the opener. Use insulated staples to
secure the wire in several places. Do not pierce
wire with a staple, creating a short or open circuit.
4. Receiver terminals are located on the back panel
of the opener.
5. Strip 11mm of insulation from the end of the bell
wire and insert in wire trap: white to 2 and
white/red to 1.
6. Permanently attach the entrapment warning label
to the wall near the door control, and the manual
release/safety reverse test in a prominent location
on the inside of the garage door.
RED
-1
Lighted Door
Control Button
HARDWARE SHOWN ACTUAL SIZE
Screw 6ABx1-1/2”
Lighted Door Control Button
Remote Control Wall Mount (optional)
1. Locate wall mount bracket at least 1.5m above the
floor.
2. Attach to the wall with 2 x ø 3.5 max flat head
screws (not provided).
3. Slide remote control onto wall mount bracket.
NOTE: Tightening the wall mount screws will reduce
clearance between bracket and wall.
114A2845
Bell Wire
17
Drywall Anchors
Insulated
Staples
WARN
ARNING
ING
WARNING
WIRING INSTRUCTIONS FOR
ACCESSORIES
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door
control.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door, out of
reach of children at a minimum height of 1.5m, and
away from all moving parts of door.
• NEVER permit children to operate or play with door
control push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep garage door in sight until completely
closed. NEVER permit anyone to cross path of closing
garage door.
AVERTISSEMENT
• Place entrapment warning label on the inside of
door as a reminder of safe operating procedures.
Place the manual release/safety reverse test
label in plain view on the inside of the garage
door.
AVERTISSEMENT
KEY SWITCH MODEL 059009
To opener terminal: white to 2; white/red to 1.
SAFETY INFRARED REVERSING SENSOR
MODEL 062153
To opener terminal screws: white to 2; Black to 3.
DOOR CONTROL PANEL 062159
To opener terminal: white to 2; white/red to 1.
INSTALLATION STEP 7
Install the Light
• Press the release tabs on both sides of lens.
Gently rotate lens back and downward until the
lens hinge is in the fully open position. Do not
remove the lens. Install a 40 watt maximum (socket
size E27), light globe in the socket as shown.
• The light will turn on and remain lit for 2-1/2
minutes when power is connected. After 2-1/2
minutes it will turn off.
• Reverse the procedure to close the lens.
Replace burned out globes with rough service
light globes.
114A2845
40W Max
Light Globe
Release tabs
of lens
Socket
18
WARN
ARNING
ING
INSTALLATION STEP 8
Attach the Emergency Release
Rope and Handle
• To prevent possible SERIOUS INJURY or DEATH from
a falling garage door:
– If possible, use emergency release handle to
disengage trolley ONLY when garage door is
CLOSED. Weak or broken springs or unbalanced
door could result in an open door falling rapidly
and/or unexpectedly.
– NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope
knot becomes untied, you could fall.
CAUTION
• Thread one end of the rope through the hole in the
top of the red handle so "NOTICE" reads right side
up as shown. Secure with an overhand knot at
least 25mm from the end of the rope to prevent
slipping.
• Thread the other end of the rope through the hole
in the release arm of the outer trolley.
• Adjust rope length so the handle is 1.8m above
the floor. Secure with an overhand knot.
If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
Overhand
Knot
Trolley
Trolley Release Arm
Rope
NOT
ICE
WARN
ARNING
ING STEP 9
INSTALLATION
WARN
ARNING
ING
Connect Electric Power
To prevent possible SERIOUS INJURY or DEATH from
electrocution or fire:
• Be sure power is not connected to the opener, and
disconnect power to circuit BEFORE removing cover to
establish permanent wiring connection.
• Garage door installation and wiring MUST be in
compliance with all local electrical and building codes.
• NEVER use an extension cord, 2-wire adapter, or
change plug in any way to make it fit outlet. Be sure
the opener is earthed.
CAUTION
WARN
ARNING
ING
To avoid installation difficulties, do not run the opener
at this time.
Connect the operator to a mains which is properly
earthed according to the wiring instruction tag
attached to the power supply cord (and as specified
by local code).
114A2845
Emergency
Release Handle
19
The units must be installed inside the garage so that
the sending and receiving eyes face each other
across the door, between 100-150mm above the
floor. Either can be installed on the left or right of the
door as long as the sun never shines directly into the
receiving eye lens.
The brackets must be securely fastened to a solid
surface such as the wall framing. If installing in
masonry construction, add a piece of wood at each
location to avoid drilling extra holes in masonry if
repositioning is necessary.
The invisible light beam path must be unobstructed.
No part of the garage door (or door tracks, springs,
hinges, rollers or other hardware) may interrupt the
beam while the door is closing.
INSTALLATION STEP 10
Install the Safety Infrared
Reversing Sensors (Optional)
It is recommended that safety infrared reversing
sensors be connected and aligned correctly to
the garage door opener.
The force, as measured on the closing edge of
the door, should not exceed 400N (40kg). If the
force is adjusted
to more than 400N, this
Theclosing
Chamberlain
Group, Inc.
safety system must be installed.
Safety Sensor
IMPORTANT INFORMATION ABOUT
Instruction
Sheet Page 1
THE SAFETY REVERSING SENSORS
Protector
System
Disk #1and
(Yellow)
When properly
connected
aligned, the safety
infrared
reversing sensors will detect an obstacle in
11/5/91
- 1/15/92
the path of its electronic beam. The sending eye
transmits an invisible light beam to the receiving eye.
If an obstruction breaks the light beam while the door
is closing, the door will stop and reverse to full open
position, and the opener light will flash 10 times.
Sensor Beam
100-150mm max.
above floor
Sensor Beam
100-150mm max.
above floor
Invisible Light Beam
Protection Area
Facing the door from inside the garage
Note: This operator, when used with safety reversing
sensor 062153, meets product standard
requirements for a monitored sensor system.
If the operator detects that the safety sensors no
longer function properly, the operator will not close
until the sensor continuity has been returned.
114A2845
20
WARN
ARNING
ING
CAUTION
INSTALLATION STEP 11
Fasten the Door Bracket
Fibreglass, aluminum or lightweight steel garage doors
WILL REQUIRE reinforcement BEFORE installation of
door bracket. To prevent damage to garage doors
reinforce inside of door with angle iron both vertically
and horizontally.
Follow instructions which apply to your door type as
illustrated below or on the following page.
A horizontal reinforcement brace should be long
enough to be secured to two or three vertical
supports. A vertical reinforcement brace should
cover the height of the top panel.
Figure 1 shows one piece of angle iron as the
horizontal brace. For the vertical brace, two pieces of
angle iron are used to create a U-shaped support.
The best solution is to check with your garage door
manufacturer for an opener installation door
reinforcement kit.
NOTE: Many door reinforcement kits provide for
direct attachment of the clevis pin and door arm. In
this case you will not need the door bracket; proceed
to Step 12.
HARDWARE SHOWN ACTUAL SIZE
Carriage Bolt 8mm x 65mm
Nut 8mm
Lock Washer 8mm
SECTIONAL DOORS
Sheet Metal Screw
1. Centre the door bracket on the previously marked
vertical centreline used for the header bracket
installation. Note correct UP placement, as
Figure 1
stamped inside the bracket.
Vertical
Vertical
2. Position the top edge of the bracket 50mm Reinforcement
Reinforcement
100mm (2"-4") below the top edge of the door, OR
Vertical
Vertical
Vertical
Reinforcement
directly below any structural support across the top
Centreline
Reinforcement
Vertical
of Garage Door
Vertical
of the door.
Centreline
Centreline
of Garage Door
Vertical
of Garage Door
Bolt
3. Mark, drill holes and install as follows, depending
Centreline
8mm x 65mm
of Garage Door
on your door’s construction:
Bolt
UP
Metal or light weight doors using a vertical angle
iron brace between the door panel support and Door
Bracket
the door bracket:
Door
Self-Threading
• Drill 4.5mm (3/16") fastening holes. Secure the
Screw Bracket
8mm x 13mm
Self-Threading
door bracket using the two 8mm x 13mm (1/4"Screw
14x5/8") self-threading screws. (Figure 2A)
8mm x 13mm
• Alternately, use two 8mm (5/16") bolts, lock
Figure 2A
washers and nuts. (Figure 2B)
Metal, insulated or light weight factory reinforced
doors:
• Drill 4.5mm (3/16") fastening holes. Secure the
door bracket using the self-threading screws.
(Figure 3)
UP
UP
Figure 2B
Inside Edge
of Door or
Reinforcement Board
Bolt
8mm x 65mm
Vertical
Centreline
of Garage Door
UP
Wood Doors:
• Use top and bottom or side to side door bracket
holes. Drill 8mm (5/16") holes through the door
and secure bracket with 8mm x 65mm (5/16"x2")
carriage bolts, lock
HARDWARE
washers and nuts (not
SHOWN
ACTUAL SIZE
provided). (Figure 4)
NOTE: The 8mm x 13mm
(1/4"-14x5/8") self-threading
Self-Threading
Screw
screws are not intended for
8mm x 13mm
use
on
wood
doors.
Self-Threading Screw
Vertical
Centreline
of Garage Door
Self-Threading
Screw
8mm x 13mm
UP
Self-Threading
Screw
8mm x 13mm
Figure 3
1/4"-14x5/8"
114A2845
UP
8mm x 65mm
Door
Bracket
Door
Lock Washer
8mm Bracket
Nut
Lock Washer
8mm
8mm
Nut
8mm
21
Inside Edge
of Door or
Reinforcement Board
Bolt
8mm x 65mm
UP
Vertical
Centreline
of Garage
Door
UP
Vertical
Figure
Centreline
of Garage
Door
4
ONE-PIECE DOORS
Please read and comply with the warnings and
reinforcement instructions on the previous page.
They apply to one-piece doors also.
• Centre the door bracket on the top of the door, in
line with the header bracket as shown. Mark either
the left and right, or the top and bottom holes.
• Metal Doors: Drill 4.5mm (3/16") pilot holes and
fasten the bracket with the 8 x 13mm (1/4"14x5/8") self-threading screws provided.
• Wood Doors: Drill 8mm (5/16") holes and use
8mm x 2" (5/16"x2") carriage bolts, lock washers
and nuts or 8 x 40mm (5/16"x1-1/2") lag screws
depending on your installation needs.
NOTE: The door bracket may be installed on the top
edge of the door if required for your installation.
(Refer to the dotted line optional placement drawing.)
HARDWARE SHOWN ACTUAL SIZE
Carriage Bolt 8mm x 65mm
Nut 8mm
Lock Washer 8mm
Sheet Metal Screw
Self-Threading
Screw
1/4"-14x5/8"
Header Wall
2x4 Support
Finished Ceiling
Door
Bracket
Top of Door
(Inside
Garage)
Top Edge
of Door
Header
Bracket
Optional
Placement
Door
Bracket
METAL DOOR
Optional
Placement
of Door
Bracket
Vertical
Centreline of
Garage Door
HORIZONTAL AND VERTICAL
REINFORCEMENT IS NEEDED
FOR LIGHTWEIGHT GARAGE
DOORS (FIBREGLASS,
ALUMINUM, STEEL, DOORS
WITH GLASS PANEL, ETC.).
(NOT PROVIDED)
Nut
5/16"-18
Door
Bracket
Lock
Washer
5/16"
Top of Door
(Inside
Garage)
Top Edge
of Door
Optional
Placement
Carriage Bolt
5/16"x2"
(Not Provided)
For a door with no exposed framing,
or for the optional installation, use
lag screws 5/16"x1-1/2" (Not Provided)
to fasten door bracket.
114A2845
22
WOOD DOOR
INSTALLATION STEP 12
Inner Trolley
Connect Door Arm to Trolley
Outer Trolley
Follow instructions which apply to your door type as
illustrated below and on the following page.
SECTIONAL DOORS ONLY
• Make sure garage door is fully closed. Pull the
emergency release handle to disconnect the outer
trolley from the inner trolley. Slide the outer trolley
back (away from the door) about 200mm as shown
in Figures 1, 2 and 3.
Ring
Fastener
Clevis Pin
8mm x 25mm
Straight
Door Arm
Door
Bracket
Figure 1:
• Fasten straight door arm section to outer trolley
with the 8mm x 25mm clevis pin. Secure the
connection with a ring fastener.
• Fasten curved section to the door bracket in the
same way, using the 8mmx 32mm clevis pin.
Curved
Door Arm
Clevis Pin
8mm x 32mm
Figure 1
Figure 2:
• Bring arm sections together. Find two pairs of
holes that line up and join sections. If possible, use
the top and bottom holes on the curved door arm,
as shown.
Figure 3, Hole Alignment Alternative:
• If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 150mm
from the solid end. Reconnect to trolley with cut
end down as shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
• Pull the emergency release handle toward the
opener at a 45° angle so that the trolley release
arm is horizontal. Proceed to Adjustment Step 1,
page 25. Trolley will re-engage automatically when
opener is operated.
Lock
Washers
8mm
Nuts
8mm
Emergency
Release
Handle
Hex Screws
8mm x 20mm
Door Bracket
Figure 2
HARDWARE SHOWN ACTUAL SIZE
Lock
Washers
8mm
Nut 8mm
Lock Washer 8mm
Clevis Pin
8mm x 25mm (Trolley)
Nuts
8mm
Ring Fastener
Hex Screws
8mm x 20mm
Hex Screw
8mm x 20mm
Cut This End
Figure 3
Clevis Pin
8mm x 32mm (Door Bracket)
114A2845
23
ALL ONE-PIECE DOORS
Door
Bracket
Assemble the Door Arm:
• Fasten the straight and curved door arm sections
together to the longest possible length (with a 2 or
3 hole overlap).
• With the door closed, connect the straight door
arm section to the door bracket with the
8mm x 32mm clevis pin.
• Secure with a ring fastener.
Ring
Fastener
Lock
Washers
8mm
Clevis Pin
8mm x 32mm
Nuts
8mm
Straight
Arm
Screws
8mm x 20mm
Curved
Door Arm
• Press the Remote Control transmitter button. The
Adjustment Procedures for One-Piece Doors
trolley will travel to the fully closed position.
On one-piece doors, before connecting the door arm
• Manually close the door and lift the door arm to the
to the trolley, the travel limits must be adjusted. Limit
trolley. The arm should touch the trolley just ahead
adjustment screws are located on the left side panel
of the door arm connector hole. Refer to the fully
as shown on page 25. Follow adjustment procedures
closed trolley/door arm positions in the illustration.
below.
If the arm is behind the connector hole, adjust the
A. Open Door Adjustment: Decrease UP
limit further. One full turn equals 50mm of trolley
Travel Limit
travel.
Fully Closed
Door
• Turn the UP limit adjustment screw counterConnect
the door arm to the trolley.
Trolley
Bracket
Ring
clockwise 4 1/2 turns.
Fastener
• Close the door and join
the curved arm to
the
Nuts
Door Arm button. The
• Press the Remote Control transmitter
connector hole in the trolley withLock
the remaining
8mm
Connector Hole
Washers
trolley will travel to the fully open position.
clevis pin. It may be necessary to
lift the door
8mm
Door Arm
Straight
slightly
the connection.
Clevis Pin to make
• Manually raise the door to
the open position
Arm
8mm x 25mm
(parallel to the floor), and lift the door arm to the
• Secure
with a ring fastener.
Emergency
Release Handle
Screws
trolley. The arm should touch the trolley just in
Curved
8mmthrough
x 20mm a complete travel cycle.
• Run the opener
If
Door Arm
back of the door arm connector hole. Refer to the
the door has a slight "backward" slant in full open
fully open trolley/door Closed
arm positions in the
position as shown in the illustration, decrease the
Door not extend far enough,
illustration. If the arm does
UP limit until the door is parallel to the floor.
adjust the limit further. One full turn equals 50mm
NOTE: When setting the up limit on the following
of trolley travel.
page, the door should not have a "backward" slant
B. Closed Door Adjustment: Decrease DOWN
when fully open as illustrated below. A slight
Fully Open
Travel Limit
backward slant will cause unnecessary
bucking
Trolley
• Turn the DOWN limit adjustment screw clockwise
and/or jerking operation as the door is being opened
4 complete turns.
or closed from the fully open position.
Correct Angle
Door Arm
Connector Hole
Fully Closed
Trolley
Door Arm
Connector Hole
Door Arm
Door with
Backward Slant
(Undesirable)
Open Door
Door Arm
Emergency Release Handle
Closed
Door
Fully Open
Trolley
Correct Angle
Door with
Backward Slant
(Undesirable)
Open Door
114A2845
24
Door Arm
Connector Hole
Door Arm
WARN
ARNING
ING
ADJUSTMENT STEP 1
Limit Adjustment
Without a properly installed safety reversal system,
persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage
door.
• Incorrect adjustment of garage door travel limits will
interfere with proper operation of safety reversal
system.
• If one control (force or travel limits) is adjusted, the
other control may also need adjustment.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on
contact with 40mm high object on floor.
CAUTION
Run the opener through a complete travel cycle.
Force adjustments are not necessary when the door
opens and closes completely and doesn't reverse
unintentionally in the fully closed position.
Locate the button on the back panel of motor unit.
NOTE: if the operator stops or reverses and will not
allow the run through of a complete travel cycle, it
may be necessary for the operator to adjust the force
profile.
WARN
ARNING
ING
Push the button twice to enter into Force Setting
Mode. Proceed with limit setting.
NOTE: Repeated operation of the opener during
adjustment procedures may cause motor to overheat
and shut off. Allow a 15 minute cooling period after 5
continuous operations of the opener.
Read the following carefully before proceeding to
Force Adjustment. Use a screwdriver to make limit
adjustments.
If Door Doesn't Open Completely but Opens at
Least 1.5m (5 feet): Increase up travel. Turn the up
limit adjustment screw clockwise. One turn equals
5cm (2") of travel.
If door does not open at least 1.5m (5 feet).
Adjust force, see Force Adjustment: Place the
opener into the Force Adjustment Mode, see Force
Adjustment.
If Door Doesn't Close Completely: If door arm is at
maximum length, increase down travel. Turn down
limit adjustment screw counterclockwise. One turn
equals 5cm (2") of travel. If the door still will not
close completely, the header bracket is positioned
too high.
If Opener Reverses in Fully Closed Position:
Decrease down travel. Turn down limit adjustment
screw clockwise. One turn equals 5cm (2") of travel.
If Door Reverses when Closing and there is no
Interference to Travel Cycle: Test door for
binding. Pull manual release handle. Manually open
and close door. If door is binding, call a door
serviceman. If door is not binding or unbalanced,
place the opener into the Force Setting Mode, see
Force Settings.
PROCEED TO “FORCE SETTINGS” TO
COMPLETE STEP “LIMIT ADJUSTMENT”. Forces
must be learned in order for limit adjustments to
operate properly.
114A2845
CAUTION
To prevent damage to vehicles, be sure fully open door
provides adequate clearance.
Limit Adjustment
Screws
25
ADJUSTMENT STEP 2
WARN
ARNING
ING
Adjust the Force
The force, as measured on the closing edge of
the door, should not exceed 400N (40kg). If the
closing force is measured to more than 400N, a
Safety Infrared Reversing Sensor must be
installed See step 3 on page 27.
The force setting button is located on the back panel
of the motor unit. The force setting
regulates
the- SEARS
Adjust
Force
amount of power required to open and close the
door. If the forces are too light, door travel may be
interrupted by nuisance reversals.
Locate the button on the back panel of motor unit.
Push the button twice to enter into Force Setting
Mode. The LED (Indicator Light) will flash. Push the
wall control or the programmed remote control that
was shipped with your opener. The door will travel to
either the OPEN or CLOSE position. Push the button
again, the door will travel to the opposite position.
Push the button again if the LED is stilling blinking.
The door must travel through a complete cycle UP
and DOWN in order for the force to be set properly. If
the unit reverses before it reaches the Open or Close
Limit repeat the process. The LED (indicator light) will
stop flashing when the force has been learned.
Without a properly installed safety reversal system,
persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage
door.
• Too much force on garage door will interfere with
proper operation of safety reversal system.
• NEVER increase force beyond minimum amount
required to close garage door.
• NEVER use force adjustments to compensate for a
binding or sticking garage door.
• If one control (force or travel limits) is adjusted, the
other control may also need adjustment.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on
contact with 40mm high object on floor.
• The force, as measured on the closing edge ot the
door, should not exceed 400N (40kg). If the closing
force is more than 400N, a Safety Infrared Reversing
Sensor must be installed. Do not use the force setting
procedure to compensate for a binding or sticking
garage door. Excessive force will interfere with the
proper operation of the Safety Reverse System or
damage the garage door.
CAUTION
Note: If unable to set limits return to page 25.
Button
Button
Press 2 times
114A2845
26
Step 3 Test Safety Reverse System SEARS 315-699 (Yellow Disk #2)
Models 53315, 53415, 535156, 53625 & 53699
ADJUSTMENT STEP
3
WARN
ARNING
ING
6/20/89 - 6/27/89
Test the Safety Reverse System
Without a properly installed safety reversal system,
persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage
door.
• Safety reversal system MUST be tested every month.
• If one control (force or travel limits) is adjusted, the
other control may also need adjustment.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on
contact with 40mm high object on the floor.
CAUTION
TEST
• With the door fully open, place a 40mm board on
the floor, centered under the garage door.
• Operate the door in the down direction. The door
must reverse on striking the obstruction.
ADJUST
• If the door stops on the obstruction, it is not
traveling far enough in the down direction.
Increase the DOWN limit by turning the DOWN
limit adjustment screw counterclockwise 1/4 turn.
NOTE: On a sectional door, make sure limit
adjustments do not force the door arm beyond a
straight up and down position. See the illustration
on page 23.
• Repeat the test.
• When the door reverses on the 40mm board,
remove the obstruction and run the opener through
3 or 4 complete travel cycles to test adjustment.
If the door will not reverse on the board after
repeated adjustment attempts, call for professional
B&D garage door service.
IMPORTANT SAFETY CHECK:
Repeat Adjustment Steps 1, 2 and 4 after:
• Each adjustment of door arm length, limits, or
force controls.
The Chamberlain Group, Inc.
• Any repair to or adjustment of the garage door
Safety
Sensor
(including
springs
and hardware).
Instruction
SheetofPage
1 floor.
• Any repair
to or buckling
the garage
• Any repair
to or adjustment
of the#1
opener.
Protector
System Disk
(Yellow)
GARAGE DOOR
40mm board laid flat
11/5/91 - 1/15/92
WARN
ARNING
ING
ADJUSTMENT STEP 4
Without a properly installed safety reversing sensor,
persons (particularly small children) could be SERIOUSLY
INJURED or KILLED by a closing garage door.
The force, as measured on the closing edge ot the door,
should not exceed 400N (40kg). If the closing force is
more than 400N, the Safety Infrared Reversing Sensor
must be installed. Do not use the force setting procedure
to compensate for a binding or sticking garage door.
Excessive force will interfere with the proper operation of
the Safety Reverse System or damage the garage door.
Test the Safety Infrared Reversing
Sensors (if installed)
CAUTION
• Press the remote control push button to open the
door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the
door. The door will not move more than 25mm,
and the door control will blink 10 times.
The garage door opener will not close from a remote
if the indicator light in either sensor is off (alerting
you to the fact that the sensor is misaligned or
obstructed).
If the opener closes the door when the safety
reversing sensor is obstructed (and the sensors
are no more than 150mm above the floor), call for
professional B&D garage door service.
Safety Reversing Sensor
114A2845
27
Safety Reversing Sensor
OPERATION
NING
WARN
ARNING
ING
IMPORTANT SAFETY INSTRUCTIONS
WARN
ARNING
ING
To reduce the risk of severe injury or death:
TION
ION
1. READ AND FOLLOW ALL WARNINGS AND
INSTRUCTIONS.
2. ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate or play with garage
door control push buttons or remote controls.
3. ONLY activate garage door when it can be seen clearly, it
is properly adjusted, and there are no obstructions to
door travel.
4. ALWAYS keep garage door in sight until completely
closed. NO ONE SHOULD CROSS THE PATH OF THE
MOVING DOOR.
5. If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or
broken springs or unbalanced door could result in an
open door falling rapidly and/or unexpectedly.
6. NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
7. NEVER use handle to pull garage door open or closed. If
rope knot becomes untied, you could fall.
8. If one control (force or travel limits) is adjusted, the
other control may also need adjustment.
9. After ANY adjustments are made, the safety reversal
system MUST be tested.
10. Safety reversal system MUST be tested every month.
Garage door MUST reverse on contact with 40mm high
object on the floor.
11. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED
(see page 3). An improperly balanced door may not
reverse when required and could result in severe injury
or death.
12. All repairs to cables, spring assemblies and other
hardware, all of which are under EXTREME tension,
MUST be made by a trained door systems technician.
13. ALWAYS disconnect electric power to garage door
opener before making any repairs or removing covers.
14. The force, as measured on the closing edge ot the door,
should not exceed 400N (40kg). If the closing force is
more than 400N, a Safety Infrared Reversing Sensor
must be installed. Do not use the force setting
procedure to compensate for a binding or sticking
garage door. Excessive force will interfere with the
proper operation of the Safety Reverse System or
damage the garage door.
15.
When the opener is activated:
1. If open, the door will close. If closed, it will open.
2. If closing, the door will stop and reverse.
3. If opening, the door will stop.
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse. If
the obstruction interrupts the sensor beam, the
opener lights will blink for five seconds.
6. If obstructed while opening, the door will stop.
7. If fully open and the Infrared Safety Reversing
Sensor is installed, the door will not close when
the beam is broken. The sensor has no effect in
the opening cycle.
The opener light will turn on under the following
conditions: when the opener is initially plugged in;
when power is restored after interruption; when the
opener is activated.
It will turn off automatically after 2-1/2 minutes. Globe
power is 40 watts maximum.
Using Your Garage Door Opener
Your opener will operate with up to twelve remote
control transmitters, one entry keypad, and one dipswitch code transmitter. If you purchase a new
remote, or if you wish to deactivate any remote,
follow the instructions in the Programming section.
Activate your opener with any of the following:
• The hand-held Remote Control: Hold the large
push button down until the door starts to move.
• The wall-mounted Door Control: Hold the push
button down until the door starts to move.
• The Keyless Entry (Optional): Must be
programmed before use.
114A2845
SAVE THESE INSTRUCTIONS.
28
To Open the Door Manually
Care of Your Opener
LIMIT AND FORCE ADJUSTMENTS:
Weather conditions may
Limit Controls
cause some minor changes in
door operation requiring some
re-adjustments, particularly
during the first year of
Adjustment Label
operation.
(Located on the left side panel)
Pages 25 and 26 refer to the
limit and force adjustments.
Force Controls
Repeat the safety reverse test (Adjustment
Step 3, page 27) after any adjustment of limits or
force.
WARN
ARNING
ING
Emergency
Release
Handle
(Pull Down)
WARN
ARNING
ING
• To Trolley
prevent possible SERIOUS INJURY or DEATH from
Releasegarage door:
a falling
Arm
– If possible, use emergency release handle to
disengage trolley ONLY when garage door is
CLOSED. Weak or broken springs or unbalanced
door could result in an open door falling rapidly
and/or unexpectedly.
– Trolley
NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
Release
Trolley
Arm
• NEVER
use handle to pull door open or closed. If rope
Release
knotArm
becomes untied, you could fall.
CAUTION
WARN
ARNING
ING
NO
TIC
E
9
Emergency
Release
Handle
NO
TIC
E
(Pull Down)
Emergency
Release Handle
(Pull Down & Back
DISCONNECT
NOTICE
Towards Opener)
1
7
MAINTENANCE SCHEDULE
NO
TIC
E
Emergency
Release
NO
TIC
Handle
E
Emergency
(Pull
Down)
Release Handle
TROLLEY:
(Pull Down & Back
Towards Opener)
TO RE-CONNECT THE
Pull the emergency release
handle toward the opener at
a 45° degree angle so that
the trolley release arm is
horizontal. The trolley will
reconnect on the next UP or
DOWN operation, either
manually or by using the
door control or remote.
Arm
3
5
5
KG
KG
THE REMOTE CONTROL BATTERY
The lithium battery should produce power for up to
5 years. To replace battery, use the visor clip or
screwdriver blade to pry open the case. Insert battery
positive side up.
Dispose of old battery properly.
NOTICE
WARN
ARNING
ING
To reconnect
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
CAUTION
114A2845
1
7
NOTICE
Trolley
Release
Arm
Emergency
Release Handle
(Pull Down & Back
Towards Opener)
9
Adjustment Label
Once a Month
(Located on the back panel)
• Manually operate door. If it is unbalanced or
binding, call for professional garage door service.
• Check to be sure door opens & closes fully. Adjust
limits and/or force if necessary. (See pages 25
and 26.)
• Repeat the safety reverse test. Make any
necessary adjustments. (See Adjustment Step 3.)
Twice a Year
• Check chain tension. Disconnect trolley first. Adjust
if necessary (see page 11).
Once a Year
• Oil door rollers, bearings and hinges. The opener
does not require additional lubrication. Do not
grease the door tracks.
• Lubricate the chain.
THE TROLLEY:
The door should be fully
closed if possible. Pull down
on theTrolley
emergency release
Release
handle
Arm(so that the trolley
Trolley
release arm snaps into a
Release
Emergency
Arm
Emergency
Release Handlevertical position) and lift the
Release
(Pull Down & Back
door manually. The lockout
Handle
Towards Opener)
feature prevents the trolley
(Pull Down)
from reconnecting
automatically, and the door
Lockout position
can be raised and lowered
(Manual disconnect)
Trolley
manually as often as
Trolley
Release
Release
necessary.
Arm
NOTICE
3
29
Troubleshooting
1. Opener doesn't operate from either door control or
remote:
• Does the opener have electric power? Plug lamp into outlet.
If it doesn't light, check the fuse box or the circuit breaker.
(Some outlets are controlled by a wall switch.)
• Have you disengaged all door locks? Review installation
instruction warnings on page 1.
• Is there a build-up of ice or snow under door? The door may
be frozen to ground. Remove any obstruction.
• The garage door spring may be broken. Have it replaced.
• Repeated operation may have tripped the overload protector
in the motor. Wait 15 minutes. Try again.
2. Opener operates from remote but not from door
control:
• Is door control button lit? If not, remove the bell wire from
the opener terminals. Short the red and white terminals by
touching both terminals at the same time with a piece of
wire. If the opener runs, check for a faulty wire connection at
the door control, a short under the staples, or a broken wire.
• Are wiring connections correct? Review page 3.
3. Door operates from door control but not from remote:
• Check battery. Replace battery if necessary.
• Is the light at the wall control flashing? Press button with
key-symbol to unlock the opener against remote controls.
• Is the receiver LED flashing at the back-side of the opener
when the transmitter is pressed? The opener receiver must
re-learn the remote control code. Follow the instructions on
page 4.
• If you purchased a new remote control then check at carton
of remote control for compatibility or call the Service Hotline.
4. Remote has short range:
• Is battery installed? If needed, change the battery.
• Change the location of the remote control on the car.
• A metal garage door, foil-backed insulation or metal siding
will reduce the transmission range.
• Use outside coaxial antenna adapter to move antenna.
5. Door reverses for no apparent reason and opener light
doesn't blink:
• Is something obstructing the door? Pull manual release
handle. Operate door manually. If it is unbalanced or
binding, call for professional garage door service.
• Clear any ice or snow from garage floor area where garage
door closes.
• Review Force Settings. Open and close the door in learn
mode for several (3-5) consecutive cycles to allow the
operator to adjust to inconsistent doors.
• If door reverses in FULLY CLOSED position, re-learn travel
limits.
Repeat safety reverse test after adjustment is complete.
The need for occasional adjustment of the force and limit
settings is normal. Weather conditions in particular can affect
door travel.
6. Door reverses for no apparent reason and opener light
blinks for 5 seconds after reversing:
Check The Safety Infrared Reversing Sensor (if you have
installed this accessory). If the light is blinking, correct
alignment.
Note: Continuously holding down the door control button will
allow the door to close if the protector system is not properly
aligned. The transmitter will not close the door. The opener
lights will blink.
114A2845
30
7. Opener noise is disturbing in living quarters of home:
If operational noise is a problem because of proximity of the
opener to the living quarters, Vibration Isolator Kit 062155
(included with the operator) can be installed. This kit was
designed to reduce the "sounding board effect" and is easy to
install.
8. The garage door opens and closes by itself:
• Delete all remote controls and reprogram.
• Make sure remote push button is not stuck "on".
• Disconnect all push buttons or key switches attached and
wait one day.
9. Door stops but doesn't close completely:
Review Limit Adjustment section.
Repeat safety reverse test after any adjustment of door arm
length, close force or down limit.
10. Door opens but won't close:
• Check The Safety Infrared Reversing Sensor (if you have
installed this accessory). If the light is blinking, correct
alignment.
• If opener light does not blink and it is a new installation,
check the down force.
Repeat the safety reverse test after the adjustment is
complete.
11. Opener light does not turn on:
Replace light bulb (40 Watts maximum). Replace burned out
bulbs with rough service light bulbs.
12. Opener light does not turn off:
There may be a defective earth at the ceiling or wall
receptacle. The unit must be earthed.
13. Opener strains or reversed during opening:
Door may be unbalanced or springs are broken. Close door
and use manual release rope and handle to disconnect trolley.
Open and close door manually. A properly balanced door will
stay in any point of travel while being supported entirely by its
springs. If it does not, call for professional garage door service
to correct the problem. Do not change force settings.
14. Opener motor hums briefly, then won't work:
• Garage door springs are broken. SEE ABOVE.
• If problem occurs on first operation of opener, door is locked.
Disable door lock. If chain was removed and reinstalled, the
motor may be out of phase. Remove chain; cycle motor to
down position. Observe drive sprocket. When it turns in
clockwise direction and stops in down position, re-install
chain.
Repeat safety reverse test after adjustment is complete.
15. Opener won't activate due to power failure:
• Pull manual release rope and handle down and back to
disconnect trolley. Door can be opened and closed manually.
When the power is restored, pull the manual release handle
straight down. The next time the opener is activated, the
trolley will reconnect.
• The Outside Quick Release accessory (if fitted) disconnects
the trolley from outside the garage in case of power failure.
9
1
7
9
3
1
7
5
3
5
KG
KG
PROGRAMMING
SPECIFICATIONS
Below are instructions for programming your opener
to operate with remote control transmitters.
Horsepower ....................1/2
Rated Pull Force.............800N
Stand-by power rating
@ 230V...........................5.5W
9
9
1
7
3
5
USING THE “SMART” BUTTON
9
1
7
9
3
1. Press and hold the button on the
hand-held remote* that you wish
to operate your garage door.
L ift M
3
5
2. Press and release the “Learn”
button on the back panel of the
opener.
KG
as
te
as
te
r
te
1
7
3
5
KG
L ift M
as
te
Receiver
Operating Frequency......433.92MHz
Computer Codes ............8
Code Switch Code..........1
Keypad Code..................1
r
r
To deactivate any unwanted remote,
first erase all codes:
Press and hold the “Learn” button on
opener until the smart indicator light
goes out (approximately 6 seconds).
All previous codes are now erased.
Reprogram each remote or keyless
entry you wish to use.
*Multi-Function Remotes
If provided with your
garage door opener,
the large button is
factory programmed to
operate it. Additional
buttons on any multifunction remote or
mini-remote can be programmed to operate other
garage door openers.
114A2845
9
Dimensions
Length (Overall)..............3.1m (122-1/2")
Headroom Required .......5cm (2")
Hanging Weight ..............14.5 kg (32 lb)
To Erase All Codes From Opener
Receiver Memory
as
3
5
KG
Safety
Personal..........................Push button and stop. Push button
and automatic reversal in down
direction. Push button and automatic
stop in up direction.
Electronic ........................Independent up and down force
adjustment screws.
Electrical .........................Motor overload protector and low
voltage push button wiring.
Limit Device ....................Circuit actuated by limit nut.
Limit Adjustment .............Screwdriver adjustment on side panel.
Start Circuit.....................Low voltage push button circuit.
r
L ift M
1
7
Drive Mechanism
Gears ..............................16:1 worm gear reduction
Drive ...............................Chain with one-piece trolley on
steel C-rail.
Length of Travel..............Adjustable to 2.29m (7-1/2 feet)
Travel Rate .....................127mm (5") per second
Lamp...............................On when door starts, off 2-1/2
minutes after stop.
Door Linkage ..................Adjustable door arm. Pull cord
trolley release.
1
7
5
KG
9
Motor
Type ................................Permanent split capacitor
Speed .............................1500 rpm
Volts ................................230-240 Volts AC-50Hz Only
Current............................2.0 amperes
KG
L if t M
3
5
KG
To Code a Hand-held Remote
Control Transmitter
3. The light bulb will blink when the
code has been accepted. If light
bulb is not installed, two clicks
will be heard.
1
7
31
WARRANTY
Controll-A-Door® Automatic Garage Door Opener
1. Definitions
‘B&D’ means
(a) in Australia - B&D Doors of 17 Oasis Court Clontarf, Queensland
4019
(b) in New Zealand - B&D Doors (NZ) Ltd of 70 Allens Road East
Tamaki Auckland, which is a subsidiary of Alesco NZ Ltd.
‘Purchaser’ means the purchaser of the Opener.
‘Opener’ means the ‘Controll-A-Door Automatic Garage Door Opener’
‘Approved Distributor’ means an approved B&D distributor of the Opener.
‘Major Components’ means all components of the Opener that make up
the power head (including any track assembly, if any), that is attached to
a garage door.
‘Ancillary Components’ means all components of the Opener which are
not Major Components.
‘Manufacturer’s Written Instruction Manual’ means the instruction
manual provided with the Opener.
2. This warranty applies to every sale of an Opener to a Purchaser by B&D
or its Approved Distributor, and is the only warranty given on behalf
of B&D.
3. B&D warrants that it will, at its option, either repair or replace any
defects:
(i) in materials or workmanship in the Opener, subject to the following:
(a) for Major Components of the Opener that are installed by B&D or
an Approved Distributor the warranty shall be valid for a period of
sixty (60) months;
(b) for Major Components of the Opener that are not installed by
B&D or an Approved Distributor the warranty shall be valid for a
period of twelve (12) months, provided that all costs of
disconnection, reinstallation and freight shall be borne by the
Purchaser.
(c) for Ancillary Components of the Opener the warranty shall be
valid for a period of twelve (12) months. Globes and batteries
excluded.
(ii) in installation for a period of twelve (12) months from the date of
installation where the Opener has been installed by B&D or its
Approved Distributor.
4. The warranties provided in clause 3(i) shall only apply to an Opener
which is being used under normal use and service in accordance with
the Manufacturer’s Written Instruction Manual and are limited to the
repair or replacement, at B&D’s option, of any defective Opener or parts
thereof.
5. The warranty provided in clause 3(i) shall apply from:
(i) the date of delivery of the Opener by B&D; or
(ii) the date of installation of the Opener by B&D or one of its Approved
Installers; or
(iii) the date of purchase of the Opener by the Purchaser; whichever is
the later.
6. (i) Where the Opener has been sold to the Purchaser by B&D, the
Purchaser shall make all warranty claims hereunder directly with B&D;
(ii) Where the Opener has been sold to the Purchaser by an Approved
Distributor, the Purchaser shall make all warranty claims hereunder
directly with the Approved Distributor.
7. The Purchaser will pay for any service call made by B&D or an
Approved Distributor where such a call is made for the purpose of
adjustment (as described in the Manufacturers Written Instruction
Manual) and not for rectification of a defect pursuant to the warranty
hereunder.
8. (i) The Purchaser shall be responsible for any expense incurred by
B&D or an Approved Distributor in ensuring that the Opener is
readily accessible for any repair work carried out under this warranty.
(ii) Where an Opener is installed outside a capital city metropolitan area
and a warranty claim is made pursuant to this warranty, any
travelling expenses and costs of transporting the Opener, incurred by
B&D or its Approved Distributor, shall be borne by the Purchaser.
9. Subject to paragraph 12 hereof;
(i) the obligations of B&D under this warranty are limited to those
contained herein and such warranties are expressly in lieu of all
other warranties, express or implied, including any implied warranty
of merchantability or fitness for a particular purpose and
notwithstanding any course of dealing between the parties or custom
and usage in the trade to the contrary.
(ii) B&D shall not be subject to nor incur and the Purchaser releases B&D
from any claim or liability (including consequential loss or damage and
loss or use or profit) by reason of delay, defective or faulty materials or
workmanship, negligence or any act, matter or thing done, admitted or
omitted by B&D.
114A2845
10. Subject to Clause 12 hereof, this warranty does not extend to and B&D
will be relieved of all obligations, responsibilities and liabilities (direct or
consequential) in the event that defects in manufacture of the Opener
are directly or indirectly in the opinion of B&D due to or result from:
(i) being fitted to any door or other closing device which is not of the
type or condition defined in the Manufacturers Written Instruction
Manual as suitable for installation of the Opener.
(ii) Lack of proper maintenance or care of the Door and Opener. Door
must be serviced in accordance to the door’s care and
maintenance instructions. Failure to maintain the door may result
in the opener warranty being voided.
(iii) Incorrect and unreasonable use.
(iv) Faulty installation or adjustment of the Opener or door to which
the Opener is connected where such installation or adjustment is
not carried out by B&D or one of its Authorised B&D Distributors.
(v) Failure to observe any instructions or directions provided with the
Opener or given to the Purchaser by B&D or an Approved
Distributor.
(vi) Modifications or repairs made or attempted to be made by any
unauthorised person.
(vii) Faulty electrical wiring of structures to which the Opener is affixed.
(viii) Radio (including citizen brand transmissions) or other electronic
interference.
(ix) Water damage, including effects from rust and corrosion.
(x) Use with doors locked.
(xi) Operation of the opener with excessively high opening or closing
force settings.
11. The warranty contained in Clause 3 does not cover batteries or globes
and B&D shall not be liable for any defect, malfunction or failure of
such items.
12. It is expressly provided that the warranties or any terms and conditions
of them or other statement contained in this document or other
literature given to the Purchaser shall not be read or applied so as to
purport to exclude, restrict or modify or have the effect of excluding,
restricting or modifying the application in relation to the supply of the
Opener of all or any of the provisions of Divisions 2 and 2A of Part V of
the Trade Practices Act, 1974, or the Consumer Guarantees Act 1993 if
the purchase is a ‘consumer’ and purchased the opener in New
Zealand, (“The Act”) as amended or the exercise of a right conferred by
such a provision or any other condition or warranty implied by any
relevant State Act or Territorial Ordinance or by the general law and
which by law cannot be excluded, restricted or modified provided that
to the extent that the Act permits B&D to limit its liability for a breach of
condition or warranty implied by the Act, B&D’s liability for such breach
shall be limited to the payment of the cost of replacing the Opener or
acquiring an equivalent Opener or repairing the Opener.
13. This warranty shall be governed by and construed in accordance with
Australian law if the opener was purchased in Australia, or New
Zealand law if the opener was purchased in New Zealand.
14. Upon making a claim under this warranty the purchaser must produce
proof of the date of purchase, together with the warranty certificate set
out below:
Purchased from:
Installed by:
Installed on (date):
The Purchaser shall complete this certificate and keep it together with
a copy of the receipt of purchase in a safe place – production of such
information will assist the handling of a claim made under this warranty.
The B&D Diamond and Controll-A-Door are registered Trademarks of
B&D Australia Pty Ltd., an Alesco company. ABN 25010473971.
©2005, All Rights Reserved
Printed in Mexico
Download PDF

advertising