CFM Corporation EF22 Indoor Fireplace User Manual

Electric Fireplace
Models: EF22
EF26/EF26FG
EF33
EF36
Homeowner's Installation and Operating Instructions
INSTALLER / CONSUMER SAFETY INFORMATION
PLEASE READ THIS MANUAL BEFORE
INSTALLING AND USING APPLIANCE
WARNING!
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, AN ELECTRICAL SHOCK OR FIRE MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR
LOSS OF LIFE.
FOR YOUR SAFETY
Service must be performed by a
qualified service agency.
DO NOT STORE OR USE
GASOLINE OR OTHER
FLAMMABLE VAPORS OR
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE.
C
US
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
10009816 8/07 Rev. 5
ARRÊT !
STOP!
¡ALTO!
NO NEED TO RETURN TO THE STORE
Questions With The Assembly?
Require Parts Information?
Product Under Manufacturer’s Warranty?
PAS BESOIN DE RETOURNER AU
MAGASIN
NO ES NECESARIO QUE REGRESE A LA
TIENDA
Des questions sur l’assemblage?
De l’information sur les pièces?
Le produit est-il garanti par le fabricant?
¿Tiene alguna pregunta sobre el ensamble?
¿Necesita información sobre las partes?
¿El producto tiene garantía del fabricante?
Appelez-nous sans frais
États-Unis : 1-800-668-5323
Canada : 1-800-668-5323
Du lundi au vendredi, de 9 h
00 à 17 h 00 HNE
Call Toll-Free
Canada: 1-800-668-5323
USA: 1-800-668-5323
Monday to Friday 9:00 A.M. to
5:00 P.M. E.S.T.
Llame sin costo
Estados Unidos: 1-800-668-5323
Canadá: 1-800-668-5323
de lunes a viernes de 9:00 A.M. a
5:00 P.M. hora estándar del este
TO HELP US HELP YOU
Fill In The Information Below:
Retain This Owner’s Manual And Proof Of Purchase For Future Reference
POUR NOUS AIDER À VOUS AIDER
Veuillez remplir les données suivantes :
Conservez ce Manuel du propriétaire et preuve d’achat pour consultation ultérieure
PARA AYUDARNOS A AYUDARLE
Complete la siguiente información:
Guarde este Manual del usuario y Prueba de compra para futuras referencias
Model Number
Numéro du modèle
Número de modelo
Date of Purchase
Date d’achat
Fecha de compra
Product Serial No.
Numéro de série du produit
Número de serie del producto
MODEL NUMBER AND PRODUCT SERIAL NUMBER CAN BE FOUND ON THE CERTIFICATION LABEL OF YOUR FIREPLACE
LE NUMÉRO DU MODÈLE ET LE NUMÉRO DE SÉRIE DU PRODUIT SE TROUVENT SUR L’ÉTIQUETTE DE CERTIFICATION
DE VOTRE FOYER
EL NÚMERO DE MODELO Y EL NÚMERO DE SERIE DEL PRODUCTO SE ENCUENTRA EN LA ETIQUETA DE CERTIFICACIÓN DE SU CHIMENEA
2
10009816
Table of Contents
Safety Information ................................................................................................................. 4
Installation Instructions
Fireplace Dimensions ................................................................................................... 5
Electrical Specifications ................................................................................................ 5
Locating Your Fireplace ................................................................................................ 6
Clearance to Combustibles ........................................................................................... 6
Cabinet Installations ..................................................................................................... 6
Electrical Connection .................................................................................................... 7
Grounding Instructions ................................................................................................. 7
Direct (Hard) Wiring Electric Fireplace ........................................................................... 8
Service Instructions
Remove Front Cover ..................................................................................................... 9
Glass Information ....................................................................................................... 10
Replacing the Light Bulbs ........................................................................................... 10
Maintenance of Motors ............................................................................................... 11
Cleaning ..................................................................................................................... 11
Electrical Wiring Diagram ............................................................................................ 12
Operating Instructions
Fireplace Control Functions ........................................................................................ 13
Flame Speed Control .................................................................................................. 14
Heater Control ............................................................................................................ 14
Overhead Light ........................................................................................................... 14
Replacement Parts ............................................................................................................... 15
Warranty ............................................................................................................................... 19
Thank you and congratulations on your purchase of a CFM Corporation electric fireplace.
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty.
Please Read the Installation & Operating Instructions
Before Using This Appliance
10009816
3
Safety Information
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains
at least 3 feet (914mm) from the front of this appliance.
3. CAUTION: Extreme caution is necessary when any heater is used
by or near children or invalids and whenever the heater is left operating unattended.
4. If possible always unplug this appliance when not in use.
5. Do not operate any heater with a damaged cord or plug or after the appliance
malfunctions, has been dropped or damaged in any manner.
6. Any repairs to this appliance should be carried out by a qualified service person.
7. Under no circumstances should this appliance be modified. Parts having to be
removed for servicing must be replaced prior to operating this appliance again.
8. Do not use outdoors.
9. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate this appliance where it may fall into a bathtub or
other water container.
10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or
the like. Arrange cord away from traffic areas and where it will not be tripped
over.
11. To disconnect this appliance, turn controls to the off position, then remove plug
from outlet.
12. Connect to properly grounded outlets only.
13. This appliance, when installed must be electrically grounded in accordance with
local codes, with the current CSA C22.1 Canadian Electrical codes or for USA
installations, follow local codes and the National Electric Code, ANSI/NFPA No.
70.
14. Do not insert or allow foreign objects to enter any ventilation or exhaust opening
as this may cause an electric shock, fire or damage the appliance.
15. To prevent possible fire, do not block air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed, where openings may become blocked.
16. This appliance has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint or flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas
stockings or decorations be hung on or near it.
17. Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.
18. Avoid the use of an extension cord because of the risk of overheating the cord
and the risk of fire. Extension cords are for temporary use only. If an extension
cord must be used, it must be UL/CSA certified, rated at 15A (1875W), 125V
maximum with 14 AWG minimum and constructed of two current carrying conductors with ground. A heavy duty extension cord with the shortest length possible for the connection is recommended and must not be longer than 50 ft. (15.2
m). Do not coil or cover the extension cord.
Save These Instructions
4
10009816
Installation Instructions
• EF22/26/33/36 Fireplace Dimensions
1” (25 mm)
C
F
J
L
E
K
J
A
D
H
B
G
Ref.
A
B
C
D
E
F
G
H
J
K
L
EF22
23¹⁄₂" (597 mm)
20³⁄₄" (527 mm)
22¹⁄₂" (571 mm)
20" (508 mm)
11¹⁄₂" (292 mm)
22" (559 mm)
21¹⁄₄" (540 mm)
15" (381 mm)
33⁷⁄₈" (860 mm)
46⁷⁄₁₆" (1179 mm)
23¹⁄₄" (590 mm)
EF26/EF26FG
27¹⁄₂” (699 mm)
25¹⁄₄” (641 mm)
26¹⁄₄” (667 mm)
24¹⁄₂” (622 mm)
11¹⁄₂” (292 mm)
18”
(457 mm)
25¹⁄₄” (641 mm)
19¹⁄₂” (495 mm)
31”
(787 mm)
43⁷⁄₈” (1114 mm)
21¹⁵⁄₁₆” (557 mm)
EF33
34¹⁄₂” (876 mm)
29³⁄₄” (743 mm)
33¹⁄₄” (845 mm)
29”
(737 mm)
11¹⁄₂” (292 mm)
25”
(635 mm)
32¹⁄₄” (819 mm)
22³⁄₄” (578 mm)
36¹⁄₁₆” (916 mm)
51” (1295 mm)
25¹⁄₂” (648 mm)
EF36
37¹⁄₂” (953 mm)
33¹⁄₄” (845 mm)
36¹⁄₄” (921 mm)
32¹⁄₂” (826 mm)
11¹⁄₂” (292 mm)
28”
(711 mm)
35¹⁄₄” (895 mm)
26¹⁄₄” (667 mm)
38¹⁄₄” (971 mm)
54¹⁄₁₆” (1373 mm)
27¹⁄₁₆” (687 mm)
NOTE: Add 1/4” (7 mm) to Ref. C and D dimensions for wall/cabinet opening clearance.
Electrical Specifications
Voltage
Total Amps
Total Watts
Heater Rating
EF22 / EF26/EF26FG
120V AC, 60 Hz
12
1450
1350 Watts
EF33 / EF36
120V AC, 60Hz
12.5
1500
1350 Watts
Units: EFJU4D0, EF0U4F0, EF0U4I0, EF0U4J0, EFJUF50
10009816
5
• Locating Your Fireplace
Your new fireplace may be installed in a prefabricated cabinet available from your
dealer.
When choosing a location for your new fireplace, ensure the general instructions are
followed. Also, for best effect install the fireplace out of direct sunlight.
• Clearance to Combustibles
Sides. . . . . . . . . . . . . . . . . . . . 0” (0
Floor . . . . . . . . . . . . . . . . . . . 0” (0
Top. . . . . . . . . . . . . . . . . . . . . 0” (0
Front . . . . . . . . . . . . . . . . 36" (914
mm)
mm)
mm)
mm)
• Cabinet Installations
Cabinets are available from your dealer which allow for fast, convenient installation
of your fireplace against existing walls.
For instructions on handling and assembly of your cabinet, refer to separate installation instructions that come with the cabinet.
If it is necessary to secure your fireplace into a cabinet or wall opening, the following
instructions apply (hardware not supplied).
Remove the glass door from the unit and set aside. 3/16” (5 mm) clearance holes,
two (2) per side must be drilled through the fireplace sides for #8 x 3/4” long black
oxide wood screws or similar. The mounting holes can be located on left and right
sides approximately 2” (51 mm) from the top and 5” (127 mm) from the bottom of
the glass door area. The mounting hole location distance from the front of the unit
must not interfere with the glass door and the refractory (brick pattern) when reinstalled. If necessary, modify the cabinet or wall opening for the mounting screws to
attach. Double check the mounting hole’s locations on the fireplace before drilling. A
small 1/16” (2 mm) pilot hole or center punch before drilling is recommended. Mark
and drill from the outside to avoid marking or damaging the interior of the fireplace.
Tighten the screws evenly so the unit remains centered in the opening and without
distorting the sides of the fireplace unit. It is advisable to place wood shims or similar between the fireplace sides and the cabinet to prevent distortion when tightening
the screws. 1/2” (13 mm) Velcro strips for securing the log to the grate tines and
away from the screen are recommended.
6
10009816
• Electrical Connection
A 15 amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required.
Preferably, the fireplace will be on a dedicated circuit as other appliances on the
same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with a 6 ft. (1.8 m) long three wire cord,
exiting the right side of the fireplace. Plan the installation to avoid the use of an
extension cord. Extension cords are for temporary use only. If an extension cord must be
used, it must be UL/CSA certified, rated at 15A (1875W), 125V maximum with 14 AWG minimum and constructed of two current carrying conductors with ground. A heavy duty extension
cord with the shortest length possible for the connection is recommended and must not be
longer than 50 ft. (15.2 m). Do not coil or cover the extension cord.
Electrical outlet wiring must comply with local building codes and
other applicable regulations to reduce the risk of fire, electrical shock
and injury to persons.
Do not use this fireplace if any part of it has been under water.
Immediately call a qualified service technician to inspect the fireplace
and replace any part of the electrical system which has been under
water.
• Grounding Instructions
This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 1.
An adapter as shown at C is available for connecting three-blade grounding-type
plugs to two-slot receptacles. The green grounding lug extending from the adapter
must be connected to a permanent ground such as a properly grounded outlet box.
The adapter should not be used if a three-slot grounded receptacle is available.
A
Figure 1
Grounding Pin
B
Cover of
Grounded
Outlet Box
C
Metal Screw
Adapter
Grounding Means
10009816
7
• Direct (Hard) Wiring Electric Fireplace
This instruction is intended as a guide for replacing the power cord supplied with
Models EF22/26/33/36 electric fireplace with direct (hard) wiring.
NOTE: When direct wiring this appliance, it must be connected to a 15 Amp
dedicated circuit breaker or fuse in the electrical panel of the dwelling. The cable
between the circuit/fuse panel and the fireplace must meet all local and national
codes, and in no case shall the wires be less than 14 gauge.
1. Make sure the power to the unit has been turned off, the power cord is
unplugged from the wall outlet and the unit has cooled down if it has been operating.
2. Follow Steps 3 through 6 in “Replacing Light Bulbs” section, Page 8, to gain
access to control panel behind the touchpad controls.
3. Locate where the power cord enters the control compartment on the right hand
side of the unit. Using wire cutters, cut the power cord within three inches (75
mm) of the point where it exits the cabinet.
4. Carefully separate the three (3) wires of the power cord into separate wires
by gently pulling them apart. DO NOT use a knife, as this may expose bare
conductor. The hot wire is connected on the right hand side and is terminated
with a 90° terminal (marked as “power” on the control board). The neutral wire
is connected on the left hand side and is terminated with a straight terminal
marked as “Neutral” on the control board. The green ground wire is attached to
a ground stud.
5. Using wire strippers, strip approximately 5/8" (15 mm) from the ends of the hot
and neutral wires.
6. Using a wrench, remove the #10-24 hex nut from the ground stud where the
green wire from the power cord is attached. Remove and discard the green
wire. Reinstall the nut but do not tighten yet.
7. While standing on the right side of the unit, locate the power cord where it exits
the cabinet. Using pliers, gently cut and remove the power cord. Dispose of the
power cord.
8. Using a slotted screwdriver, remove the 7/8" (22 mm) diameter knockout from
the right hand side of the cabinet above where the strain relief was located.
9. Route the electrical cable from the breaker/fuse panel through the 7/8" (22mm)
diameter hole and secure to the cabinet using an approved clamp. The power
wires should extend approximately 6" (152mm) into the control compartment.
10. Connect the ground wire from the power cable by wrapping it around the
ground stud of the unit and securing it using the #6-32 nut.
11. Using a wire nut, connect the hot lead (black), of the power cable to the power
cord wire that ends in 90° terminal (on the control board side, it ends on your
right hand side). Similarly, connect the neutral wire (white), of the power cable
to the power cord ending with the straight terminal (on the control board side, it
ends on your left hand side) using a wire nut. It is recommended that the wire
nuts be taped to the wires, using electrical tape, as an extra safety measure.
12. Visually check that none of the wires in the control compartment have been dislodged from the controls. If they have, use the wiring diagram on the unit or in
the instruction manual to replace them in their proper location.
13. Turn the power to the unit on at the breaker/fuse panel. Place the unit into operation and check to make sure that all of the systems are working properly.
8
WA R N I N G : T h i s
procedure
must
be conducted by a
qualified electrician, in accordance with National and
local codes. In the U.S.A.,
the installation must conform
to the National Electrical
Code, ANSI/NFPA No. 70.
In Canada, the installation
must conform to the current CSA C22.1 Canadian
Electrical Code.
WARNING: Make
sure the power to
the unit is off, and
the power cord is unplugged
from the wall outlet before
proceeding with this conversion. Failure to do so may
result in property damage,
personal injury or loss of
life.
WARNING: Make
sure the power to
the power cable
has been turned off at the
breaker/fuse panel of the
residence before proceeding.
10009816
Service Instructions
• Remove Front Cover
Access to heater/fan
1. Turn off power to the unit.
2. Let fireplace cool if it has been
operating.
3. To remove the doors, locate
and remove the two (2) screws
holding the door at the top.
(Fig. 2) Hold the door at all
times with one hand to prevent
the door from falling when you
undo the hinge screws.
4. Locate the screws that hold the
front cover in place. There are
six (6) screws, three (3)
located on the front of the
unit (Fig. 3), and three (3)
located underneath the top
shelf of the unit. (Fig. 4)
5. Remove screws using
appropriate screwdriver.
6. Pull out the front cover.
holding both sides of the
cover, pull gently towards
you and down.
7. You now have access to
the heater/fan unit, for cleaning
and/or maintenance.
8. To reinstall the front cover,
please follow reverse procedure, paying attention not to
damage any wiring in the process.
WARNING:
Disconnect
power
before
attempting any
maintenance or cleaning to reduce the risk of
fire, electrical shock or
personal injury.
Figure 2
Remove
Screws
FP1733
Figure 3
������
������������������
Remove Screws
����
Remove Screws
FP1734
Figure 4
������
�������������������
����
Figure 5
�������
�����������������������
����
FP1736
10009816
9
• Glass Information
1.
2.
3.
4.
Under no circumstances should this product be operated with broken glass.
Do not strike or slam the glass.
Do not use abrasive cleaners to clean the glass.
This product uses tempered glass. Replacement of the glass supplied by the
manufacturer should be done by a qualified service person.
• Replacing the Light Bulbs
Depending on your model, the fireplace uses two (2) or three (3) clear 120 Volt,
60 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located
under the ember bed. Units with overhead lights (Fig. 9) use two (2) clear 120 Volt,
5 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located
above the logs. For convenience, if one of the light bulbs burns out, it may be easier
to replace all of the light bulbs at the same time.
Do not exceed 60 Watts per bulb for the ember bed bulbs and 5 Watts per
bulb for the overhead lights. Use of higher rated bulbs may result in a fire,
causing property damage, personal injury or loss of life.
1.
2.
3.
4.
Turn off power to the unit.
Let fireplace cool if it has been operating.
Open the front doors.
Locate two (2) screws that hold the refractory (brick patterned) bracket together
with the ember bed. (Fig. 6) NOTE: Some units may have two (2) screws securing the refractories to the ember bed. These screws must also be removed.
(not shown)
Figure 6
FP1737
Remove Screws
5. Remove those two (2) screws using an appropriate screwdriver. One screw is
located on either side of the unit.
6. Pull the ember bed out of the unit by gently pulling towards you and only slightly
upwards. Depending on the model, you can remove the refractory prior to
removing the ember bed.
������
������������������������
����
Figure 7
Pull Here
(both sides)
FP1738
10009816
10
������
��������������
7. Looking into the opening of the unit under the ember bed, visually locate the
light bulbs.
8. Remove the light bulbs by unscrewing them out of the bases turning them counterclockwise. You can use one hand to hold the light socket in place, if required.
9. Install the new light bulb(s) by turning the light bulb into the base clockwise. You
can use one hand to hold the light socket in place, if required.
10. Reposition the ember bed. If required, gently raise the refractory panels, one at
a time, to tuck the ember bed edge underneath them.
11. Reposition the refractory bracket, aligning the refractory in place as required.
12. Reinstall the two (2) screws removed in Step 5.
Figure 8
Figure 9
4W (Max. 5W)
Light Bulb
FP1618
60W Light Bulbs
FP1739
• Maintenance
of Motors
������
Always disconnect
the appliance from the main power supply and allow ������
it to
�����������������
cool before any servicing
operation.
����
WARNING: Make
�������������� sure the power
is turned OFF
The motors used on the fan heater and flame blower are pre-lubricated for extended
����
before
proceeding.
bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the appliance around the air intake and exhaust, as well as the fan heater is
recommended. For heavy or continuous use, periodic cleaning must be done more
frequently. If the heater blows alternating cold and warm air, check the fan for free
movement and for debris restricting air flow. If the fan does not move freely, the unit
must be turned off and the fan replaced immediately in order to prevent further damage to the unit.
• Cleaning
Cleaning of the touchpad label at the bottom front of the unit is to be done only
using a soft cloth, slightly dampened in water (if needed, a small amount of dish
soap can be added to the water) and dried using a clean, dry soft cloth. Cleaning of
the screen diffuser is to be done using only water and a lint free cloth. DO NOT use
any abrasive household cleaners as these products will damage the touchpad controls and the diffusing screen.
10009816
11
• Electrical Wiring Diagram
Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with
national and local codes.
If repairing or replacing any electrical component or wiring, the original wire routing, color coding
and securing locations must be followed.
6
1
BLACK
RED
BLUE
FAN
MOTOR
LIMIT SWITCH
1.
2.
3.
4.
5.
6.
7.
8.
9.
BLUE
7
6
3
6
5
FLAME
MOTOR
BLACK/BLUE
WHITE
4
7 BLACK/BLUE
RED
1 RED
8 BLACK/BLUE
BLACK
6 WHITE
LIGHT
RETURN
2 WHITE
4
WHITE
5 WHITE
Fan/Heater
Circuit Board
Motor DC
Light Socket w/Wiring Assy
Light Bulb
Wire Clip
Bushing Snap
Strain Relief
Power Cord 16/3
BLACK/BLUE
LAMP
LIGHT
LAMP
RETURN
5
2
NEUTRAL
4
5
N.O.
HEATER
RETURN
GROUND
COM.
+
MOTOR
LINE
8
9
GREEN
NEUTRAL
NOTE: EF22/26 use 2 instead of 3
light bulbs for flame and ember bed.
WARNING: Disconnect Power Before Servicing
FP1572
HEF wiring
Any electrical05
re-wiring of this appliance must be done by a qualified
4/05
electrician. This wiring must be done in accordance with local codes and/
or in Canada with the current CSA C22.1 Canadian Electrical Code, and
for US installations, the National Electrical Code ANSI/NFPA NO 70.
12
10009816
Operating Instructions
• Fireplace Control Functions
All of the fireplace control functions can be accessed in two (2) ways:
•
•
Using a multifunction remote control unit.
Using touchpad control panel, located in the lower right-hand corner of the fireplace behind the door front.
The infrared remote control relies on a line of sight and must be pointed at the
touchpad control panel of the fireplace to work. The remote control unit has all the
controls required to operate any electronic features on the unit. If you prefer to use
the touchpad control on the fireplace unit itself, open the doors to access the touchpad buttons. The layout of the buttons on touchpads and remote control unit can be
seen in Figures 10 & 11, respectively.
The fireplace features conveniently separate controls for flame effect and for heater
control. This allows you to operate the unit in three (3) different modes:
•
•
•
As a full-featured fireplace - both flame effect and heater are on. This mode
allows you to enjoy the look of the fire along with the heat output of a heater.
As a visual effect - only flame effect is on, the heater is off. We recommend this
mode for warm weather application, when you want the ambiance of a fire, without any heat output.
As a heater - only heater is on, while the flame effect is off. This mode allows you
to use your fireplace as an electric heater, without any flame effect
Refer to Figures 10 & 11 for locations of the buttons on both, the touchpad and
remote control unit, described in the following operating instructions. Note that in
both cases, button numbers as shown in the figures are the same.
NOTE: When the flame or heater is activated by buttons 1 or 4 on either the remote
control or touchpad control panel, the respective LED lights up to indicate and allow
settings to be changed. After 20 seconds of inactivity, a feature of the fireplace is for
the LED visuals on the touchpad control panel to go out. You must activate the fireplace electronics by depressing any buttons on the remote control or the touchpad
control panel for the LED visuals to reappear before any settings can be made or
changed.
Figure 11
Figure 10
3
3
B
A
6
2
1
6
4
2
5
5
7
I/O
I/O
4
7
1
FP1614
10009816
FP1614
VCEF touchpad
4/06
FP1615
13
• Flame Speed Control
Your fireplace features a flame speed that can be controlled either by remote control or at the touchpad control panel. By depressing button 1 once, the flame effect
will be activated and turn on. By repeatedly depressing buttons 2 or 3, you can
decrease or increase the flame effect speed to achieve the desired flame effect.
Refer to the visual indicator A to monitor the relative speed of the flame effect
between the slowest (lowest light bar) and fastest (highest light bar). For your added
convenience, the flame effect speed setting is stored in memory when the flame
effect is turned off.
• Heater Control
Your fireplace features a heater with a built-in thermostat and a variable temperature setting that can be controlled either by remote control or at the touchpad control panel. By depressing button 4 once, the heater will be activated and the LED
visual indicator B lights up to indicate the temperature setting of the heater between
the lowest (lowest light bar) and highest (highest light bar). To determine the room
temperature, depress button 5 or 6 to decrease or increase until the heater goes
off or comes on. The heater is designed to safely deliver the maximum amount of
heat when it is turned on. To increase the room temperature, depress button 6 to
increase room temperature setting. When the set temperature is reached, the heater
will automatically cycle on and off to maintain the temperature setting for the room.
It is suggested that you increase the temperature setting gradually to a room temperature that you are comfortable with. For your added convenience, the temperature setting is stored in memory when the heater is turned off.
• Overhead Light
Your fireplace features overhead lights that add warmth and glow to the refractories
and logs. It is turned on or off either by remote control or at the touchpad control
panel. Depressing button 7 switches the overhead lights on or off while the flame is
on. If the flame is switched off, the overhead lights will go off but will come back on
when the flame is switched back on. This feature is not available on the EF22.
14
10009816
1
4
3
2
6
5
15
7
8
12
9
10
14
216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS)
216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS}
305mm [12"]
11
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,
without notice.
EF22/26/33/36 Electric Fireplace
Ref.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Description
Logset
Ember Lava Rock
Circuit Board
Refractory Right side
Refractory Left Side
DC Motor
Flame Generator Assembly
Glass Operable Door Assembly - Left
Glass Operable Door Assembly - Right
Socket w/Wire Assembly
Power Cord
Heater Fan Assembly
Screen Diffuser (not shown)
Transmitter
Fixed Glass
10009816
EF22
10006656
10009800
10009815
10010090
10010090
10009621
10003566
--10006453
10003095
10006538
10007912
10009283
10008175
EF26/EF26FG
10009234
10009801
10009815
10010091
10010091
10009621
10003566
10009269
10009270
10006453
10003095
10006538
10007874
10009275
10008721
EF33
10009235
10009238
10009815
10010093
10010092
10009621
10003350
10009271
10009272
10006454
10003095
10006538
10006422
10009275
--
EF36
10009236
10009239
10009815
10010095
10010094
10009621
10003350
10009273
10009274
10006454
10003095
10006538
10006576
10009275
--
15
1 YEAR WARRANTY
For CFM Corporation Electric Fireplace
BASIC WARRANTY:
CFM Corporation (hereinafter referred to collectively as
the "Company") warrants that your new electric fireplace
is free from manufacturing and material defects for a
period of one year from date of installation, subject to
the following conditions and limitations.
1. This electric fireplace must be installed and operated at all times in accordance with the Installation
and Operating instructions furnished with the product.
Any alteration, willful abuse, accident, or misuse of the
product shall nullify this warranty.
2. This warranty is non-transferrable, and is made to the
original owner, provided that the purchase was made
through an authorized supplier of the Company.
3. This warranty is limited to the repair or replacement of
part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected to
normal conditions of use and service, after said defect is
confirmed by the Company's inspection.
4. This warranty does not cover the lightbulb(s)
included with the fireplace.
5. The Company may, at its discretion, fully discharge all
obligations with respect to this warranty by refunding the
wholesale price of the defective part(s).
6. Any installation, labor, construction, transportation, or
other related costs/expenses arising from defective
part(s), repair, replacement, or otherwise of same, will
not be covered by this warranty, nor shall the Company
assume responsibility for same. Further, the Company
will not be responsible for any incidental, indirect, or
consequential damages, except as provided by law.
7. All other warranties - expressed or implied - with respect
to the product, its components and accessories, or any
obligations/liabilities on the part of the Company are
hereby expressly excluded.
8. The Company neither assumes, nor authorizes any third
party to assume, on its behalf, any other liabilities with
respect to the sale of this Northern Flame product.
9. The warranties as outlined within this document do not
apply to non-CFM Corporation accessories used in conjunction with the installation of this product.
This warranty is void if:
a) The fireplace has been operated in atmospheres
contaminated by chlorine, fluorine or other damaging
chemicals.
b) The fireplace is subjected to prolonged periods of
dampness or condensation.
c) Any alteration, willful abuse, accident, or misuse of the
product.
IF WARRANTY SERVICE IS NEEDED . . .
1) Contact your supplier. Make sure you have your
warranty, your sales receipt, and the model/serial number
of your CFM Corporation product.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK
YOURSELF.
CFM Corporation
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6
800-668-5323 • www.cfmcorp.com