Chamberlain 3575 3 HP Garage Door Opener User Manual

Model 98LM
Motion Detecting Door Control Panel
WARNING
OWNERS INSTRUCTIONS
WARNING
FOR USE WITH GARAGE DOOR OPENERS
MANUFACTURED AFTER JANUARY 1, 1995.
This door control contains a motion detector
that will automatically turn on the light when
it detects a person entering the garage. This
feature can be easily turned off for extended
work light use.
Locate the door control within sight of the door at a
minimum height of 5 feet where small children cannot
reach, and away from all moving parts of the door and
door hardware.
INSTALLATION
The door control is typically attached directly to the wall.
For pre-wired installations (as in new home construction) it
can be mounted to a standard single gang box. See
illustrations. If installing the door control adjacent to
existing door controls be sure the detector switch is
accessable.
• Disconnect power to the garage door opener.
• Strip 1/4" of insulation from one end of the bell wire.
Connect the wire to the two screw terminals on the back
of the door control as follows: white wire to W and
white/red wire to R.
NOTE: After installation, the green indicator light behind
the push bar cover will indicate proper connection.
• Remove the push bar cover by gently prying off the top
edge with a coin or screwdriver.
• For standard wall mount, mark the wall about 3/4" up the
centerline from the bottom of the door control. Install a
6ABx1-1/4" self-tapping screw at this point, allowing about
1/8" to protrude from the
STANDARD WALL MOUNT
wall. Slip the lower part
To
Replace
of the door control over
Insert Top
the screw head and
Tabs First
adjust for snug fit. Drill
and install the top screw
with care to avoid
Detector
cracking the plastic
Switch
ON
housing. Do not
OFF
Push Bar Cover
overtighten. Run the bell
wire up the wall and
across the ceiling to the opener. Use insulated staples to
secure the wire in several places. Be careful not to pierce
the wire with a staple, creating a short.
CAUTION
LOCK
LIGHT
WARNING
DO NOT CONNECT TO LIVE ELECTRICAL WIRING. CONNECT ONLY
TO 24 VOLT LOW VOLTAGE WIRES. CONNECTION TO LIVE WIRES
OR HIGHER VOLTAGE MAY CAUSE SERIOUS INJURY FROM SHOCK,
BURN OR ELECTROCUTION.
Children operating or playing with a garage door opener can injure
themselves or others. The garage door could close and cause
serious injury or death.
Install the door control (or any additional push buttons) out of the
reach of children and away from all moving parts of the door and
door hardware, but where the garage door is visible. Do not allow
children to operate the push button(s) or the remote control
transmitter(s).
A moving garage door could injure someone under it. Activate the
opener only when the door is properly adjusted, you can see it
clearly, and there are no obstructions to door travel.
• For pre-wired installations, partially install a 6-32x1"
machine screw into the bottom of the gang box, allowing
about 1/8" to protrude. Slip the lower part of the door
control over the screw head and adjust for snug fit. Install
top screw with care to avoid cracking plastic housing. Do
not overtighten.
• Connect the bell wire to the opener terminal screws as
follows: white to 2 and white/red to 1.
• After testing, replace the cover by inserting top tabs and
snapping into place.
NOTE: The automatic light feature will become functional
6-1/2 minutes after power is restored.
PRE-WIRED INSTALLATION
24 Volt
2-Conductor Bell Wire
To Replace
Insert Top
Tabs First
LOCK
LIGHT
LOCK
Push Bar Cover
Opener Terminal Screws
Push Bar
2-Conductor
Bell Wire
1
2
E
WHIT
2
3
9
1
7
1
RED
Door
Control
Terminal
Screws
3
9
1
7
3
5
5
KG
KG
LOCK
Lock
Button
LIGH
T
Light Button
Opener Panel
Antenna
LIGHT
Detector
Switch
ON
OFF
OPERATION
Door Control Push Bar: Press to open or close the door.
Press again to reverse the door during the closing cycle, or
to stop the door while it is opening.
Light Feature: Press the Light button to switch the opener
light on or off. When the door is opened or closed, the light
will remain on for 4-1/2 minutes. Press the Light button to
turn it off sooner. The Light button will not control the
opener light when the door is in motion. When using the
opener lights as working lights, we recommend that you
first disable the motion sensor. See Automatic Light
Override Feature, below.
When used with openers manufactured after
December 1, 1999, (check the date on the opener panel)
the 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or
3-1/2 minutes as follows: Press and hold the Lock button
until the light blinks (about 10 seconds). A single blink
indicates that the timer is reset to 1-1/2 minutes. Repeat
the procedure and the light will blink twice, resetting the
timer to 2-1/2 minutes. Repeat again for a 3-1/2 minute
interval, etc., up to a maximum of four blinks and 4-1/2
minutes.
Automatic Light Feature: The opener light will turn on
automatically when a person enters the garage. When a
person walks in front of the door control, the opener light
will come on for five minutes, then shut off. This feature
works by detecting body heat. It is more sensitive in front
of the door control than at its sides, and works better as a
person moves closer. It may not work in temperatures
around 100˚F.
To disable this feature, slide the Detector Switch on the
right side of the door control down (off).
Special note for older garage door openers: If this door
control is installed on an opener manufactured from
January 1, 1995 to December 1, 1999, the following
difference may apply: If the light is on when the opener is
actuated, the light may go off for a moment, then turn on
again as the detector senses you.
Automatic Light Override Feature: We recommend that
you disable the motion sensor when using the opener
lights as working lights. Otherwise, they will turn off
automatically if you are working beyond the sensor’s
range. Slide the Detector Switch on the right side of the
door control down (off), then press the light button to
control the lights.
114A2396B
Energy Saving Feature: This door control senses the
brightness inside the garage, and will not turn the light on if
it is already bright enough. If the light sensor turns on the
light when it is not needed or does not turn it on when it is
dark, the sensitivity can be adjusted. Remove the push bar
cover by gently prying off the top edge with a coin or
screwdriver. Underneath there is a dial below the green
light on the right side. Use a small screwdriver to turn the
dial by 1/4 turns: counterclockwise to make the light come
on, or clockwise to make the light go off. Replace the cover
by inserting top tabs and snapping into place.
Lock Feature: Designed to prevent operation of the door
from portable remote controls. However, the door will open
and close from the Door Control push bar and from the
Keylock and Keyless Entry accessories.
To activate: Press and hold the Lock button for 2 seconds.
The push button indicator light will flash as long as the lock
is on.
To turn off: Press and hold the Lock button again for
2 seconds. The indicator light will stop flashing. Normal
operation will resume. The Lock feature will also turn off
whenever the Smart button on the opener end panel is
activated.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-528-2817
© 2000, The Chamberlain Group, Inc.
All Rights Reserved
Printed in China