Chamberlain 3800C Garage Door Opener User Manual

The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.chamberlain.com
RESIDENTIAL GATE OPERATOR
Models GA400D and GA420D
For Residential Use Only
Owner’s Manual
■
Please read this manual and the enclosed safety materials carefully!
■
Periodic checks of the operator are required to ensure safe operation.
■
The model number label is located inside the control box of your operator.
■
Serial #
■
Installation Date
TABLE OF CONTENTS
2-7
INTRODUCTION
32-35 PROGRAMMING
2
3
4-5
6
6
7
7
Safety Symbol and Signal Word Review
Operator Specifications
Safety Installation Information
Carton Inventory
Hardware Inventory
Additional Items for Purchase
Tools Needed
32-33
34
35
35
35
8-12
PREPARATION AND OVERVIEW
8
9
10
11
12
Single Gate Overview
Dual Gate Overview
Check Your Gate
Gate Travel
Mounting Options
36
36
37
37
38
39
40-42
43-44
Important Safety Information
Using Your Gate Operator
Manual Release
Maintenance
Wiring Diagram
Diagnostic Chart
Troubleshooting
Repair Parts
45
ACCESSORIES
46
WARRANTY
46
REPAIR PARTS AND SERVICE
Program Limits
Force/Timer To Close/Party Mode Controls
To Add or Reprogram a Remote Control
To Add a Wireless Keyless Entry
To Erase All Codes
36-44 OPERATION AND MAINTENANCE
13-22 INSTALLATION
13-20
21-22
Attach Operator to Gate
Mount the Control Box
23-31 WIRING
23-24
25-28
29-31
Connect Gate Operator (Gate 1) to Control Box
Connect Gate Operator (Gate 2) to Control Box
(Model GA420D Only)
Connect Indoor Transformer to Low Voltage Wire
and Battery
BACK TEMPLATE FOR POST BRACKET MOUNTING
INTRODUCTION
Safety Symbol and Signal Word Review
This gate operator has been designed and tested to offer safe service provided it is installed, operated, maintained and
tested in strict accordance with the instructions and warnings contained in this manual.
When you see these Safety Symbols and Signal Words on
the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the
warnings that accompany them. The hazard may come
from something mechanical or from electric shock. Read
the warnings carefully.
When you see this Signal Word on the following pages, it
will alert you to the possibility of damage to your gate and/
or the gate operator if you do not comply with the
cautionary statements that accompany it. Read them
carefully.
WARNING
WARNING
Mechanical
CAUTION
WARNING
WARNING
WARNING
WARNING
Electrical
WARNING
CAUTION
Introduction
WARNING
2
Operator Specifications
Main Supply (Motor)
Accessory Power
Power Consumption
Battery Charger Supply
Maximum Gate Length
Maximum Gate Weight
Travel Time
Temperature
Protection Fuse Battery 1
Protection Fuse Battery 2
12Vdc Battery run. Operational between 11.5Vdc and 14.5Vdc.
12V nominal Class II battery voltage source is limited to:
• Solar or AC Cable up to 50' - 500 mA
• AC Cable 50' up to 250' - 250mA
• AC Cable 250' up to 1000' - 100mA
NOTE: Increased accessory power drawn from the operator will shorten the
battery life.
30 Watts max (during battery charging)
14.5Vac nominal, 30 VA max.
18 ft. at 350 lbs.
850 lbs. at 6 ft.
20 seconds (typical)
-20ºC to +50ºC, -4ºF to 122ºF Contact Technical Support for applications
below -20ºC
ATC 20A
ATC 20A
3
Introduction
Safety Installation Information
1. READ and FOLLOW all instructions.
2. The gate operator is intended for use with Class I
vehicular swing gates.
Class I denotes a vehicular gate operator (or system)
intended for use in a home of one to four single family
dwellings, or a garage or parking area associated
therewith.
Install the gate operator only when the operator is
appropriate for the construction and the usage class of
the gate.
3. Gate operating system designers, installers and users
must take into account the possible hazards associated
with each individual application. Improperly designed,
installed or maintained systems can create risks for the
user as well as the bystander. Gate system design and
installation must reduce public exposure to potential
hazards. All exposed pinch points must be eliminated
or guarded.
4. A gate operator can create high levels of force during
normal operation. Therefore, safety features must be
incorporated into every installation. Specific safety
features include safety sensors.
5. The gate must be properly installed and work freely in
both directions prior to the installation of the gate
operator.
6. The gate must be installed in a location so that enough
clearance is provided between the gate and adjacent
structures when opening and closing to reduce the risk
of entrapment. Swinging gates shall not open into
public access areas.
7. The operator is intended for use only on gates used for
vehicles. Pedestrians must be supplied with a separate
access opening. The pedestrian access opening shall
be designed to promote pedestrian usage. The
pedestrian access shall be located such that persons
will not come in contact with the moving vehicular gate.
9. For an installation utilizing non-contact sensors (safety
sensors), see product manual on the placement of
non-contact sensors (safety sensors) for each type of
application.
a. Care shall be exercised to reduce the risk of
nuisance tripping, such as when a vehicle trips the
safety sensor while the gate is still moving.
b. One or more non-contact sensors (safety sensors)
shall be located where the risk of entrapment or
obstruction exists, such as the perimeter reachable
by a moving gate or barrier.
10. For a gate operator utilizing a contact sensor such as
an edge sensor:
a. A hard wired contact sensor shall be located and its
wiring arranged so the communication between the
sensor and the gate operator is not subject to
mechanical damage.
b. One or more contact sensors shall be located on the
inside and outside leading edge of a swing gate.
Additionally, if the bottom edge of a swing gate is
greater than 6" (152 mm) above the ground at any
point in its arc of travel, one or more contact sensors
shall be located on the bottom edge.
11. Never mount any device that operates the gate
operator where the user can reach over, under, around
or through the gate to operate the controls. Controls
are to be placed at least 6' (1.8 m) from any part of the
moving gate:
• A hard wired control device shall be located and its
wiring arranged so that communication between the
control device and the gate operator is not subject to
mechanical damage.
8. Pedestrians should never cross the pathway of a
moving gate. The gate operator is not acceptable for
use on any pedestrian gate. Pedestrians must be
supplied with a separate pedestrian access.
Introduction
4
12. Controls intended to be used to reset an operator after
2 sequential activations of the entrapment protection
device or devices must be located in the line of sight
of the gate, or easily accessible controls shall have a
security feature to prevent unauthorized use. Never
allow anyone to hang on or ride the gate during the
entire travel of the gate.
13. Each gate operator is provided with two safety warning
placards. The placards are to be installed on the front
and back of the gate where they are plainly visible.
The placards may be mounted using cable ties
through the four holes provided on each placard.
All warning signs and placards must be installed where
visible in the area of the gate.
WARNING
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Install warning signs on the front and back of the gate in
PLAIN VIEW.
• Permanently secure each warning sign in a suitable manner
using fastening holes.
CAUTION
AVERTISSEMENT
ATTENTION
Moving Gate Can Cause
Injury or Death
KEEP CLEAR! Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance
14. To AVOID damaging gas, power, or other underground
utility lines, contact underground utility locating
companies BEFORE digging.
15. SAVE INSTRUCTIONS.
ADVERTENCIA
PRECAUCIÓN
5
Introduction
Carton Inventory
This operator comes with the hardware to install on a gate that pulls-to-open. If your application requires the gate to be
pushed open, accessory kit 919GA is required.
Gate Bracket
Model GA400D (1)
Model GA420D (2)
Extension Bracket
Model GA400D (1)
Model GA420D (2)
Post Bracket
Model GA400D (1)
Model GA420D (2)
Plug-In Transformer (1)
Cable Ties (4)
Moving Gate Can Cause
Injury or Death
KEEP CLEAR! Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only
Pedestrians must use separate entrance
Control Box (1) with:
1 Battery (GA400D)
2 Batteries (GA420D)
SECURITY✚®
3-Button Remote Control (1)
Warning Signs (2)
Wire Nuts (6)
Model GA420D ONLY
Arm End Cap
Model GA400D (1)
Model GA420D (2)
Gate Operator
Model GA400D (1)
Model GA420D (2)
Extension Cable
Model GA420D ONLY
Watertight Connector
Model GA420D ONLY
Installation DVD
Hardware Inventory
NOTE: Hardware quantities shown below are for GA400D. Quantities are doubled for GA420D.
Flange Nut 5/16"-18 (1)
Release Pin (1)
Flange Nut 3/8"-16 (1)
Ribbed Neck Bolt
3/8"-16x1-1/2" (1)
Lock Washer 3/8" (2)
Hex Nut 3/8"-16 (2)
Ribbed Neck Bolt
5/16"-18x1-1/2" (1)
Hairpin Clip (1)
Hex Head Shoulder
Bolt (1)
Lock Nut With
Nylon Insert (1)
Flat Washer 3/8" (2)
Carriage Bolt 3/8"-16x6" (2)
Introduction
6
Additional Items For Purchase
The following items are REQUIRED to complete the installation.
GA420D Only:
All Models:
JUNCTION BOX
SAFETY SENSORS
The Safety Sensors, model 916GA, are intended for
installation with the operators covered in this manual.
To order call: 1-866-826-4943 or visit
www.chamberlain-diy.com.
HARDWARE
• 5/16" mounting hardware for gate bracket.
• The following hardware is needed to mount the control box
depending on the mounting surface:
Wood: Four #8 1-1/4" zinc plated wood screws.
Metal: Four #10-32x6" zinc plated machine screws with
nut and lock washers.
Concrete, Brick, etc.: Four 1/4" x 1-3/4" masonry screws.
The Junction Box is needed to connect the second arm to
the extension cable (GA420D Installation Only).
• UL Listed outdoor/all-weather junction box with a
minimum of two 3/4" NPT threaded port and appropriate
all-weather cover.
• Conduit fitting to connect 3/4" PVC Schedule 40 conduit
to junction box.
CONDUIT
The conduit is needed to hold the interconnecting cable
between the Junction and Control Box (GA420D
Installation Only).
• 3/4" diameter UL Listed outdoor electrical conduit
LOW VOLTAGE WIRE
The low voltage wire is needed to connect the transformer
to the control box. The specific length required depends on
the distance from the indoor outlet to the control box.
Measure carefully, it is not recommended to splice low
voltage wire.
UL approved Class 1 or Class 3 direct burial/underground,
sunlight/UV resistant 16 gauge 2-conductor/stranded low
voltage lighting wire.
The following products are available at most home center
hardware stores and meet these specifications:
• Chamberlain Models 917GA or 918GA
AUTOMATIC GATE LOCK AND HARD STOPS (OPTIONAL)
In windy areas to ensure the gate stops at the same place
each time we recommended the purchase of an automatic
gate lock for the closed position and hard stop(s) for the
open position.
Tools Needed
During assembly, installation and adjustment of the operator, instructions will call for tools as illustrated below.
Deep Well Sockets
and Wrench
1/2", 5/8", 7/16", 9/16"
and 1/4"
Drill Bits
1/2", 3/16", 5/16"
and 5/32"
Drill
Clamps
Welder (Optional)
1
Carpenter's Level
Screwdriver
2
Pencil
Adjustable End Wrench
Tape Measure
Phillips Head Screwdriver
Hammer
Wire Strippers (Optional)
7
Wire Cutters (Optional)
Introduction
PREPARATION AND OVERVIEW
Single Gate Overview
Left-Hand Gate
ts
Ou
ide
To prevent SERIOUS INJURY or DEATH; one or more
non-contact sensors shall be located where the risk of
entrapment or obstruction exists.
p
Pro
y
er t
Warning Sign
Hinge
use
n Ca
Ca
te athat any
e
g Ga or De
mov
vin
or
e may .
Mo Injury
Gat ning gate
the
AR! r war
P CLEout prio operate
e
KEE with
dren .
only anc
time let chil area icles e entr
veh arat
not gate
Do in the e is foruse sep
anc t
play
entr mus
Thisestrians
Ped
Antenna
Post Bracket
Gate Bracket
Control Box
with Batteries
Gate Operator (Gate 1)
Operator Cable
o
on
i
t
ec
Dir avel
Tr
a
fG
te
1
PVC conduit (not provided) to
protect the power cable and
low voltage wire from lawn
mowers and string trimmers
I
de
nsi
P
e
rop
rty
Ou
ts
id
NOTE: One or more non-contact
sensors are located where the risk
of entrapment or obstruction exists
at either the opening or closing
direction. Exercise care to reduce
the risk of nuisance tripping, such
as, when a vehicle trips the sensor
while the gate is still moving.
e
Pr
op
Right-Hand Gate
er
Warning Sign
ty
Hinge
esu
a
yna
Cn
hta aC et
ta e eD aG
gn
vom ro
yam yru ivo
tag .gninra etaG jnI M
eht
w r !RA
o
etar
E
epo irp tuo LC PE
htiw EK
n
artnylno s
. erd
e et elcih aera e lihc te emit
l
t
ara ev
pes rof ag eht ton oD
esu si e
n
tsu cnar i yalp
m s tne
nair sih
tsed T
eP
ro e
ecn
Antenna
Post Bracket
Gate Bracket
Gate Operator (Gate 1)
Control Box
with Batteries
of
n l
io ve
ct ra
re T
Di te 1
Ga
Operator Cable
In
si
de
Pr
op
PVC conduit (not provided) to
protect the power cable and
low voltage wire from lawn
mowers and string trimmers
er
ty
Preparation and Overview
8
Dual Gate Overview
Junction Box
erty
ide
s
Out
p
Pro
Extension Cable
Warning Sign
Gate Operator (Gate 2)
Hinge
n Ca
PVC conduit (not provided)
to protect the power cable
and low voltage wire from
lawn mowers and
string trimmers.
use
Ca
te athat any
e
g Ga or De
mov
vin
or
e may .
Mo Injury
Gat ning gate
the
AR! r war
P CLEout prio operate
e
KEE with
dren .
only anc
time let chil area icles e entr
veh arat
not gate
Do in the e is foruse sep
anc t
play
entr mus
Thisestrians
Ped
Antenna
of el
n
o
cti Trav
e
r
Di ate 2
G
Post Bracket
Gate Bracket
Control Box
with Batteries
Gate Operator (Gate 1)
Operator Cable
of el
n
o
cti Trav
e
r
Di ate 1
G
rty
ide
Ins
pe
Pro
PVC conduit (not provided) to
protect the power cable and
low voltage wire from lawn
mowers and string trimmers.
9
Preparation and Overview
Check Your Gate
Gate and gate post MUST
be plumb.
Gate MUST be level.
Remove ANY/ALL wheels from the bottom of gate.
Gate MUST NOT hit or drag across ground.
Gate MUST swing freely and be supported entirely by its hinges.
Preparation and Overview
10
Gate Travel
Determine how your gate is to be opened.
Pull-to-Open
Gate opens into the property. Bracket for Pull-To-Open
installation is provided.
y
pe
rt
eP
ty
Di
Ga rec
In
te tio
si
Tr n o
de
av f
Pr
el
o
O
id
uts
er
rop
Push-to-Open
Gate opens away from the property and will require the Push-to-Open
kit 919GA. Refer to the Push-To-Open kit for instructions.
de
Pr
op
er
ty
of
n
o
ti avel
c
r
e
Dir ate T
G
si
P
rty
In
Ou
de
t si
e
rop
11
Preparation and Overview
Mounting Options
Mounting locations vary depending on type and style of your gate.
NOTES:
• The top of operator must be mounted at least 10" up from ground. Environmental conditions should be considered at
this time. In windy areas to ensure the gate stops at the same place each time we recommended the purchase of an
automatic gate lock for the closed position and hard stop(s) for the open position.
• Not recommended for plastic or vinyl gates. Refer to gate manufacturer for recommendation and options.
Recommended:
= Gate post bracket mounting locations
= Gate bracket mount locations
Right-Hand Hinge Mounted
Left-Hand Hinge Mounted
Typical Chain Link Gate
Typical Chain Link Gate
Typical Farm/Ranch Gate
Typical Farm/Ranch Gate
Typical Wood Gate
Typical Wood Gate
Typical Tubular Metal Gate
Typical Tubular Metal Gate
Preparation and Overview
12
INSTALLATION
Attach Operator to Gate
1
Identify Hinge Type
The illustrations below show common gate hinges. There are many styles of hinges available.
J-Bolt Hinge
Top View
Gate Post
Gate Post
J-Bolt Hinge Point
J-Bolt Hinge Point
Butt Hinge
Gate Post
Butt Hinge Point
Gate Post
Butt Hinge Point
Barrel Hinge
Gate Post
Barrel Hinge Point
13
Installation
2
Measuring and Marking for the Gate Bracket
Before proceeding, begin with the gate in the fully closed position. There are two methods described to determine
proper location of the post brackets:
• Paper template (to be cut out) located on the back page of this manual.
• Tape measure.
Either method will work depending on preference. NOTE: Be sure gate is in closed position before proceeding.
Template Method
Place the template (provided on the back page) under the gate hinge point. Use a screwdriver or dowel rod to
temporarily mark the location in front of the gate post.
Left Side Bracket Mounting
Right Side Bracket Mounting
Gate Post
Gate Hinge Point
Gate Hinge Point
Gate Post
TOP VIEW
TOP VIEW
Gate Post
Gate Post
Use a screwdriver or dowel rod to
temporarily mark measurement.
Use a screwdriver or dowel rod to
temporarily mark measurement.
Tape Measure Method
Place the measuring tape under the gate hinge point and measure 5-3/4". Use a screwdriver or dowel rod to
temporarily mark the location of the first measurement.
Right Side Bracket Mounting
Left Side Bracket Mounting
Gate Post
Gate Post
Gate Hinge Point
Gate Hinge Point
5-3/4" X
Gate Post
X 5-3/4"
Gate Post
Measure 5-3/4" from the previous mark.
Gate Post
Gate Hinge Point
Gate Post
Gate Hinge Point
X
X
5-3/4"
5-3/4"
Use the screwdriver or dowel rod to mark the location of the second measurement.
Gate Post
Gate Hinge Point
Gate Hinge Point
X First Marking
Installation
First Marking X
14
Gate Post
3
Position the Extension Bracket to Post Bracket
Assemble post bracket by placing the extension bracket on top of post bracket. Insert bolt through brackets
and fasten with flange nut. DO NOT TIGHTEN AT THIS TIME.
Right-Hand Gate
Left-Hand Gate
3/8 Ribbed Neck Bolt
3/8 Ribbed Neck Bolt
Extension Bracket
Extension Bracket
Post Bracket
Post Bracket
Flange Nut
Flange Nut
Hold post bracket in desired position. Align extension bracket to a position as CLOSE AS POSSIBLE
above the marker.
15
Installation
4
Remove Motor Assembly
Remove screws (4) and remove motor assembly. Set motor aside and place in clean, dry location.
NOTE: Turn operator over to remove screws.
Screws
Motor
THIS
TO G SIDE
ATE
5
Determine Maximum Piston Travel
To ensure proper operation, it is essential to keep the
piston from extending and retracting completely.
2
1
“Manually extend piston out
as far as possible, push back
1/4" (.64 cm) and then mark.”
Piston
“Slowly extend the piston 1/4"
(.64 cm) from collar and draw
a mark.”
3
Installation
“Always stay within these two marks
to prevent the piston from bottoming
out which could damage the
transmission.”
16
6
Attach Brackets to Gate Operator
Attach post bracket to gate operator using hex head shoulder bolt and lock nut with nylon insert. Attach gate
bracket to operator using release pin and hairpin clip.
Hex Head Shoulder Bolt
Release Pin
Post Bracket
Gate Bracket
Hairpin Clip
Lock Nut with
Nylon Insert
7
Position Gate Bracket
Hold the gate operator against the gate. The gate operator (arm) must be level. Clamp bracket to gate. Some
installations require a reinforcement be installed on the gate.
“After adjustments have been made,
make sure the piston is still within
marked range.”
Piston Range
17
Installation
Visually check the clearance. Holding the gate firmly, slowly walk the gate to the fully open position. Check for pinch
points at the post mount area.
av
el
Pa
th
Path
Ga
te
Gate
el
Tr a v
Tr
8
Check Piston Travel
Allow a minimum of 1/4" between the post bracket and operator. Adjust gate bracket if the piston marks are not
visible in both the open and close direction. Tighten both bolts after final adjustments are made. Bolts should be
fully seated into the brackets.
NOTE: If gate does not open and close completely, adjust the position of the gate bracket.
Minimum of 1/4"
Installation
18
9
Secure Gate Bracket to Gate
Remove the operator from the brackets. Mark and drill holes in gate or reinforcement (if necessary) according to
gate bracket mounting hardware. Secure the gate bracket to gate using hardware (not provided).
NOTE: The gate bracket can be secured to the gate using a welder (optional).
5/16"-18 U-Bolt
Hex Nut
Lock Washer
Lock Down Bolt 1/4"-20
Flat Washer
Gate
Bracket
10
NOTE: For mounting on flat
surfaces, use 5/16"-18 Hex Bolts (4)
through slots instead of U-Bolts.
Secure Post Bracket to Gate Post
Mark holes for the post bracket. Remove the clamp and operator. Drill clearance holes for 3/8"-16 bolt in gate post.
NOTE: The post bracket can be secured to the gate post using a welder (optional).
Welder Optional
Secure the post bracket to gate post using hardware. The gate operator (arm) must be level.
Flat Washers
Hex Nuts
Lock Washers
Carriage Bolts
19
Installation
Slide motor assembly onto arm and secure
with screws (4). NOTE: Turn operator over
to re-install screws. Attach arm cover.
If installing a second gate operator repeat
steps 1-12.
NOTE: The arm brackets must be reversed
or mirrored on the second operator.
NOTE: Motor housing screws must
be fully tightened with screw heads
recessed below housing surface.
Screws
Motor
Arm Cover
THI
S
TO GSIDE
ATE
11
Reattach Motor Assembly
“THIS SIDE TO GATE”
label MUST face the gate.
Arm
12
13
14
Attach Operator to Gate and Bracket
Make sure “THIS SIDE TO GATE” label faces the gate
when reattaching operator to gate. Tighten all bracket
connections.
For Model GA420D Only
Repeat Steps 1-12 for second operator.
Warning Sign Placement
WARNING
Warning placards MUST be installed on both
sides of the gate and in plain view. Fasten to
gate with cable ties.
Fence
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Install warning signs on the front and back of the gate
in PLAIN VIEW.
• Permanently secure each warning sign in a suitable manner
using fastening holes.
CAUTION
Gate Post
Gate
Moving Gate Can Cause
Injury or Death
KEEP CLEAR! Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only
Pedestrians must use separate entrance
GATE TRAVEL
PATH
AVERTISSEMENT
ATTENTION
Inside Property
Installation
20
Mount the Control Box
The control box MUST be mounted within 5' of the gate
operator. Mount the control box as high as possible for
best radio reception.
1
Open the Control Box
Screws (4)
Remove screws and open the control box.
RESET
2
Remove the Control Board
Coaxial
Connector
Disconnect reset button, alarm and coaxial
connector. Loosen screws and remove control
board and mounting bracket. Remove batteries and
set aside.
Screws
Screws
ALARM
ON
LEARN
XMITTER
OFF
LOCK /
BIPART DELAY
C7
C7Ø
C71
BR
C72
K2
K2
GR
C73
WH
18
YL
BL
Alarm
Control Board
Z22
Z22
L1
LOCK
GATE 1
GATE 1
RD
K1
K1
F8
F8
SET
CLOSE
LIMIT
Q9
Q9
Z12
Z12
SET
SET
OPEN
OPEN
LIMIT
LIMIT
24V
24V
LEARN
LIMITS
GATE 2
TIMER
RUNNING
CTRL PWR
OVLD
R9Ø
R9
R9
R9Ø
OPEN
BR
BR
SINGLE BUTTON
GR
GR
RESET
K4
K4
WH
WH
STOP
YL
YL
COM
BL
BL
COM
K3
K3
RD
RD
R184
GATE22
GATE
F7
F7
Z4
Z4
D16
D16
C13
C13
D2
D2
D129
D129
F9
F9
C2
C2
R4
R4
DB1
DB1
JU2
JU2
MOV2
MOV2
30
30
MOV1
MOV1
C69
C69
C11
C11
AC PWR
/SOLAR
K6
K6
C64
C64
JU1
3ØA
3 3ØA
32V
3AA 32V
30
30
U2 R22
U2 R22
JU1
JU1
F3
F3
F2
F2
R42
R42Ø
R42Ø
R42
R423
R423
R329
R329
R27
R27
D1
D1
J21
J21
J24
33
AA 32V
J24 J23
J23 3ØA
3ØA
32V
F1
F1
CHGR
OVLD
Reset Button
Connections
Screws
Z22
Z22
L1
ON
LEARN
XMITTER
OFF
LOCK /
BIPART DELAY
Screws
C7Ø
C71
BR
C72
K2
K2
GR
C73
WH
18
YL
BL
GATE 1
RD
K1
K1
F8
F8
SET
CLOSE
LIMIT
Q9
Q9
Z12
Z12
SET
SET
OPEN
OPEN
LIMIT
LIMIT
24V
24V
LEARN
LIMITS
GATE 2
TIMER
RUNNING
CTRL PWR
OVLD
R9Ø
R9Ø
BR
BR
GR
GR
K4
K4
WH
WH
YL
YL
BL
BL
K3
K3
RD
RD
R184
F7
F7
Z4
Z4
D16
D16
C13
C13
D2
D2
D129
D129
F9
F9
F2
F2
Knock Outs
Knock Outs
CHGR
OVLD
MOV1
MOV1
JU1
JU1
C11
C11
F3
F3
C69
C69
R42Ø
R42Ø
R423
R423
R329
R329
R27
R27
D1
D1
F1
F1
J24
J24 J23
J23 3ØA
3ØA 32V
32V
AC PWR
/SOLAR
R4
R4
JU2
JU2
JU1
Knock Outs
Knock Outs
Z22
Z22
L1
ON
LEARN
XMITTER
OFF
LOCK /
BIPART DELAY
C7Ø
C71
BR
C72
K2
K2
GR
C73
WH
18
YL
BL
GATE 1
RD
K1
K1
F8
F8
SET
CLOSE
LIMIT
Q9
Q9
Z12
Z12
SET
SET
OPEN
OPEN
LIMIT
LIMIT
24V
24V
LEARN
LIMITS
GATE 2
TIMER
RUNNING
CTRL PWR
OVLD
R9Ø
R9Ø
BR
BR
GR
GR
K4
K4
WH
WH
YL
YL
BL
BL
K3
K3
RD
RD
R184
GATE22
GATE
F7
F7
Z4
Z4
D16
D16
C13
C13
D2
D2
D129
D129
F9
F9
MOV1
MOV1
CHGR
OVLD
AC PWR
/SOLAR
C2
C2
K6
K6
R4
R4
JU2
JU2
MOV2
MOV2
C64
C64
DB1
DB1
C69
C69
C11
C11
Knock Outs
JU1
3ØA
32V
3ØA 32V
30
30
U2 R22
U2 R22
JU1
JU1
F3
F3
F2
F2
R42Ø
R42Ø
R423
R423
R329
R329
R27
R27
D1
D1
J21
J21
J24
J24 J23
J23 3ØA
3ØA 32V
32V
F1
F1
30
30
DB1
DB1
MOV2
MOV2
30
30
K6
K6
C64
C64
3ØA
32V
3ØA 32V
30
30
U2 R22
U2 R22
C2
C2
Select holes to be used for mounting and knock out
using a screwdriver and hammer.
J21
J21
3
Select Mounting Holes
GATE22
GATE
21
Installation
Z22
Z22
L1
ON
LEARN
XMITTER
OFF
LOCK /
BIPART DELAY
C7Ø
C71
BR
WH
YL
K2
K2
GR
C72
C73
18
4
Mount the Control Box
Secure the control box to mounting surface (post,
wall, column, etc.) using appropriate hardware
(not provided).
Square
Gate Post
Wall
Concrete
Anchor
U-Bolt
(Not Provided)
Screw
5
Install the Control Board
Attach antenna. Reinstall batteries, control board,
alarm, and reset button. Reconnect coaxial connector.
NOTE: Make sure battery leads are on the left side of
the control box and not pinched.
Coaxial
Connector
Screws
Screws
ALARM
ON
LEARN
XMITTER
OFF
LOCK /
BIPART DELAY
GATE 1
C7
C7Ø
C71
BR
C72
K2
K2
GR
C73
WH
18
YL
BL
Alarm
Control Board
Z22
Z22
L1
LOCK
GATE 1
RD
K1
K1
F8
F8
SET
CLOSE
LIMIT
Q9
Q9
Z12
Z12
SET
SET
OPEN
OPEN
LIMIT
LIMIT
24V
24V
LEARN
LIMITS
GATE 2
TIMER
RUNNING
CTRL PWR
OVLD
R9Ø
R9
R9
R9Ø
OPEN
BR
BR
SINGLE BUTTON
GR
GR
RESET
K4
K4
WH
WH
STOP
YL
YL
COM
BL
BL
COM
K3
K3
RD
RD
R184
GATE22
GATE
F7
F7
Z4
Z4
D16
D16
C13
C13
D2
D2
D129
D129
F9
F9
AC PWR
/SOLAR
C2
C2
R4
R4
JU2
JU2
MOV2
MOV2
30
30
MOV1
MOV1
DB1
DB1
C69
C69
C11
C11
K6
K6
C64
C64
JU1
3ØA
3 3ØA
32V
3AA 32V
30
30
U2 R22
U2 R22
JU1
JU1
F3
F3
F2
F2
R42
R42Ø
R42Ø
R42
R423
R423
R329
R329
R27
R27
D1
D1
J21
J21
J24
33
AA 32V
J24 J23
J23 3ØA
3ØA
32V
F1
F1
CHGR
OVLD
Reset Button
Connections
Screws
Z22
Z22
Screws
CTRL PWR
OVLD
R184
CHGR
OVLD
C2
C2
AC PWR
/SOLAR
R4
R4
MOV2
MOV2
Installation
22
Antenna
NG
WARNING
WIRING
N
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
• ANY maintenance to the operator or in the area near the
operator MUST not be performed until disconnecting the
electrical power and locking-out the power via the operator
power switch. Upon completion of maintenance the area
MUST be cleared and secured, at that time the unit may be
returned to service.
• Disconnect power at the fuse box BEFORE proceeding.
Operator MUST be properly grounded and connected in
accordance with local electrical codes. NOTE: The operator
should be on a separate fused line with a 15 amp
circuit breaker.
• ALL electrical connections MUST be made by a qualified
individual.
EMENT
• DO NOT install ANY wiring or attempt to run the operator
without consulting the wiring diagram. We recommend that
you install an optional reversing edge BEFORE proceeding
with the control station installation.
• ALL power wiring should be on a dedicated circuit and well
protected. The location of the power disconnect should be
visible and clearly labeled.
• ALL power and control wiring MUST be run in separate
conduit.
• BEFORE installing power wiring or control stations be sure to
follow ALL specifications and warnings described below.
Failure to do so may result in SEVERE INJURY to persons
and/or damage to operator.
AVERTISSEMENT
ON
AVERTISSEMENT
Connect Gate Operator (Gate 1) to Control Box
1
Watertight Connector Nut
Insert operator cable through watertight connector nut.
Watertight Connector Nut
Operator
Cable
NCIA
2
ADVERTENCIA
Insert Operator Cable
Insert watertight connector into the bottom of the control box and tighten with nut. Insert operator
cable through watertight connector mounted in the bottom of the control box.
ADVERTENCIA
ÓN
P1
C66
C65
D36
C68
J18
Nut
Z22
P1
Q6
K6
U4
D42
Z1
C75
C33
NO
F12
K5
ALARM
R2
C
K5
MAGLOCK
C7Ø
C7
Ø
D1Ø
D1
Ø
C71
C72
K2
L1
Q12
NO
C73
C
U4
NC
OFF
18
Z9
MAGLOCK
LEARN
XMITTER
R1
F11
ON
R2
Z1
use
n Ca
Ca
R93
te ath any
g Ga De ve at
vin y or mo
Mo InjurGate mayning. gate or
the
AR! r war
P CLE prio operate
e
KEEe without dren .
only anc
tim let chil area icles e entr
veh arat
not gate
Do in the e is foruse sep
anc st
play
entr mu
Thisestrians
Ped
GATE 1
Q1
10A 32V
GATE 1
F3
BRN
GRN
F8
K2
SET
OPEN
LIMIT
K1
D1Ø
Z8
WHT
SET
CLOSE
LIMIT
LEARN
LIMITS
Z12
Q9
DIAGNOSTIC
GATE 2
YEL
BLU
GATE 1
24V
J2Ø
J2
Ø
R9Ø
R9
Ø
RED
K1 Q9
Z12
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
BR
R1ØØ
R1
ØØ
R1Ø1
R1
1
GR
GATE 2
TIMER
RUNNING
WH
K4
R9Ø
ACCESSORY
POWER
YL
24V
TIMER TO
CLOSE
BL
D44
D8
FORCE
R1Ø1
K3
RD
R1ØØ
GATE 2
F4
F7
Z4
Q22
F9
R196
MAX
F2
OFF
C2
R4
JU2
MOV2
30
K6
U2 R22
32V
32V
Control Box
C11
3ØA
3 A
C11
3ØA
3 A
C4
C64
30
C13
U3
JU1
F7
Z4
D22
F3
J23
J21
D27 Z3
MOV1
F1
D9
C12
R329
R27
J24
R35
D8
Q22
R42Ø
R42
Ø
R423
D1
D21
K3
C69
F5
BLU
RED
GATE 2
C13
D2
D129
K4
YEL
R9
WHT
U3
ACCESSORY
OVLD
10A 32V
D4
BRN
GRN
D16
Watertight
Connector
DB1
D15
R4
C2
R196
F6
24 VAC/
SOLAR
INPUT
J4
F2
MOV2
R9
MOV1
D4
D1
C64
JMPR2
JMPR1
D2
U2
FUSE
OPEN
D6
DB1
Watertight
Connector
Operator
Cable
Watertight
Connector Nut
23
Wiring
3
Connect Operator to Control Board
Extend operator cable and wires to GATE 1 connector and
connect as shown. Tighten watertight connector nut.
NC
R223
P1
CLOSE
EDGE
K6
ALARM
R2Ø7
NO
Z2Ø
R227
C
K5
MAGLOCK
OPEN EDGE/
PHOTO
NO
Z1
L1
R224
C
Z22
R92
U4
NC
ON
R2
Z1
10A 32V
OFF
Terminal blocks
can be removed
to simplify wiring.
Z9
MAGLOCK
LEARN
XMITTER
R1
OPEN
PHOTO
10A 32V
GATE 1
R91
F3
BRN
D1Ø
GRN
GATE 1
Brown
R94
K2
Z8
WHT
CLOSE
PHOTO
DIAGNOSTIC
U4
YEL
R93
BLU
GATE 1
RED
BRN
K1 Q9
Z12
D1Ø
GRN
SET
OPEN
LIMIT
LEARN
LIMITS
GATE 2
24V
TIMER
RUNNING
CONTROL
INPUTS
OPEN
R1ØØ
SINGLE BUTTON
F4
GRN
RESET
ACCESSORY
OVLD
10A 32V
STOP
K4
YEL
OFF
MAX
COM
F5
WHT
BLU
COM
D21
RED
POWER
R35
D9
K3
D8
GATE 2
C12
D27 Z3
F7
Z4
Q22
Yellow
COM
OVLD
TIMER TO
CLOSE
FORCE
R1Ø1
BRN
WHT
White
SET
CLOSE
LIMIT
R9Ø
ACCESSORY
POWER
Green
C13
D22
LOOP
INPUTS
C4
SHADOW
U3
INTERRUPT
C11
MAX
YEL
R196
F6
24 VAC/
SOLAR
INPUT
J4
Blue
C2
F2
MOV2
R9
MOV1
C4
JMPR1
JMPR2
D2
U2
FUSE
OPEN
BATT 2
BATT 1
D6
DB1
F1 20A 32V
D4
D1
C64
C13
BLU
COM
CHGR
OVLD
D15
R4
F6
F2
Red
FUSE
OPEN
RED
Z12
CONTROL BOX
ACCESSORY
POWER
R9Ø
Operator Cable
Watertight Connector Nut
use
n Ca
Ca
te ath any
g Ga De ve at
vin y or mo
Mo InjurGate mayning. gate or
the
AR! r war
P CLEout prion operate
e
KEEe with
dre .
only anc
tim let chil area icles e entr
veh arat
not gate
Do in the e is foruse sep
anc st
play
entr mu
Thisestrians
Ped
Operator Cable
If installing one operator, proceed to page 29.
If installing two operators, continue to the next page.
Wiring
24
P1
C66
C65
C68
J18
D36
Z22
Connect Gate Operator (Gate 2) to Control Box (Model GA420D Only)
Q6
U4
K5
C33
Z1
C75
F12
D42
R2
C7Ø
D1Ø
C71
Q12
K2
C72
C73
F11
18
R93
GATE 1
Q1
SET
OPEN
LIMIT
K1
F8
SET
CLOSE
LIMIT
LEARN
LIMITS
Z12
Q9
GATE 2
Occasionally in dual gate installations, one gate would need to open first and close second. This would happen if there
was an ornamental overhang on one gate or if using a solenoid lock, for example. This gate is called the Primary gate
and needs to be connected to Gate 1 connections on the control board. Thus, it is preferred that the control box be
installed on the same side as this gate. If there is no appropriate location on that side for the control box, then mount the
control box on the opposite side, but connect the operator closest to the control box to the Gate 2 connector and the
operator on the opposite side to the Gate 1 connector.
24V
J2Ø
R9Ø
P1
R1ØØ
BR
R1Ø1
C66
C65
GR
D36
BL
C68
J18
YL
K4
WH
D44
Z22
D8
K3
RD
F7
D4
GATE 2
Z4
D2
C75
Q6
U4
C13
Q22
U3
F12
K5
D16
D42
C33
D129
F9
R2
R9
Z1
R196
F2
R42Ø
R423
Q12
C2
C73
C11
C72
JU1
K6
32V
32V
DB1
R4
F11
JU2
U2 R22
R93
MOV2
18
C64
3ØA
3ØA
30
30
J21
R329
R27
C71
MOV1
D1
J24
K2 J23
F3
C69
C7Ø
D1Ø
F1
GATE 1
Q1
SET
OPEN
LIMIT
K1
F8
SET
CLOSE
LIMIT
LEARN
LIMITS
Z12
Q9
24V
R9Ø
R1ØØ
J2Ø
BR
GATE 2
R1Ø1
GR
K4
WH
YL
BL
D44
D8
K3
RD
F7
D4
GATE 2
Z4
C13
D2
U3
D16
Q22
D129
R9
F9
R196
F2
C2
C11
JU1
MOV1
J23
J21
R329
R27
F3
C69
R42Ø
R423
D1
J24
F1
JU2
R4
U2 R22
MOV2
3ØA
3ØA
C64
30
30
K6
32V
32V
DB1
Set the Lock/Bipart Delay
The LOCK/BIPART DELAY switch on the control board
needs to be set to the ON position.
The following illustration shows a dual gate configuration
with a decorative overlapping piece on the outside of the
gate.
ON
OFF
LOCK/
BIPART DELAY
P1
C66
C65
C7Ø
C71
C68
J18
D36
Z22
Q6
U4
C75
C33
Z1
F12
K5
D42
R2
C7Ø
C7
D1Ø
D1
C71
Q12
K2
C72
C73
F11
18
R93
GATE 1
Q1
SET
OPEN
LIMIT
K1
F8
SET
CLOSE
LIMIT
LEARN
LIMITS
Z12
Q9
24V
BR
R9Ø
R9
R1ØØ
R1ØØ
J2Ø
J2
Outside Property
GATE 2
R1Ø1
R1
GR
K4
WH
YL
BL
D44
D8
K3
RD
F7
D4
GATE 2
Z4
C13
D2
U3
D16
Q22
D129
R9
F9
R196
F2
MOV1
JU1
C2
JU2
R4
U2 R22
MOV2
3ØA
3 A
3
3ØA
A
30
K6
C64
30
32V
32V
Control Box
C11
J23
J21
R329
R27
F3
C69
R42
R42Ø
R423
D1
J24
F1
DB1
Primary Gate - Connect to Gate 1 Connector on Control
Board.
Primary Gate
Outside Property
If a solenoid lock is being used on a gate, the gate with
the lock attached to it would be the primary gate.
25
Wiring
WARNING
1
Connect second Operator to Control
Board (Model Ga420D Only)
CAUTION
To AVOID damaging gas, power or other underground utility
lines, contact underground utility locating companies BEFORE
digging.
• Before digging, contact local underground utility
locating companies.
• Trench across driveway to bury the extension
cable.
• Use PVC conduit to prevent damage to cables.
• Insert extension cable through watertight
connector nut and through an available watertight
connector mounted in the control box.
• Extend cable and wires to GATE 2 connector and
connect as shown.
• Secure extension cable to control box using
watertight connector nut.
AVERTISSEMENT
ATTENTION
ACCESSORY
POWER
R9Ø
R223
P1
CLOSE
EDGE
K6
ALARM
R2Ø7
NO
Z2Ø
R227
C
K5
MAGLOCK
P1
24V
R224
ON
R2
Z1
GATE 1
NO
R91
BRN
D1Ø
GRN
R94
K2
OFF
WHT
CLOSE
PHOTO
DIAGNOSTIC
MAGLOCK
LEARN
XMITTER
R1
YEL
R93
BLU
F3
D1Ø
GRN
GATE 1
RED
K2
K1 Q9
Z12
WHT
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
Terminal blocks
can be removed
to simplify wiring.
DIAGNOSTIC
YEL
R9Ø
ACCESSORY
POWER
BLU
GATE 2
TIMER
RUNNING
COM
OVLD
GATE 1
RED
24V
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
10A 32V
R9Ø
24V
LEARN
LIMITS
BRN
TIMER
RUNNING
STOP
OFF
MAX
COM
F5
COM
D21
POWER
R35
D9
K3
D8
C12
D27 Z3
F7
Z4
ACCESSORY
OVLD
WHT
CONTROL
INPUTS
OPEN
RESET
ACCESSORY
OVLD
K4
BLU
RED
GATE 2
F4
10A 32V
SINGLE BUTTON
F4
10A 32V
WHT
YEL
TIMER TO
CLOSE
R1ØØ
GRN
R1ØØ
GRN
GATE 2
FORCE
R1Ø1
BRN
TIMER TO
CLOSE
FORCE
R1Ø1
K1 Q9
Z12
ACCESSORY
POWER
Q22
C13
D22
LOOP
INPUTS
C4
SHADOW
U3
K4
YEL
OFF
MAX
INTERRUPT
C11
F5
BLU
R4
R35
D9
K3
D8
C12
D27 Z3
C13
D22
C2
R196
C4
J4
F2
MOV2
R9
MOV1
JMPR2
JMPR1
D2
U2
FUSE
OPEN
BATT 2
BATT 1
D6
DB1
F1 20A 32V
D4
D1
C64
U3
C11
COM
F6
24 VAC/
SOLAR
INPUT
F7
Z4
Q22
CHGR
OVLD
D15
D21
RED
GATE 2
BLU
Control Box
Z8
U4
ON
R2
10A 32V
BRN
YEL
Z9
OPEN
PHOTO
F3
L1
NC
WHT
OFF
MAGLOCK
LEARN
XMITTER
R1
10A 32V
C
GATE 1
GRN
Z22
R92
U4
K5
Z1
BRN
L1
NC
NO
C
MAGLOCK
Brown
Green
White
Yellow
Blue
Red
OPEN EDGE/
PHOTO
NO
C
K6
ALARM
D15
R4
C2
R196
F6
24 VAC/
SOLAR
INPUT
J4
F2
MOV2
R9
MOV1
D4
D1
C64
JMPR2
JMPR1
D2
U2
D6
DB1
RED
GATE 2
D15
R4
C2
R196
24 VAC/
SOLAR
INPUT
Operator
Cable
Extension Cable
PVC Conduit
ADVERTENCIA
Junction Box
Extension Cable
PRECAUCIÓN
Gate Operator (Gate 2)
se
Can
Cau
te ath any
g Ga De e at
vin ry or mov
Mo Inju Gate maying. gate or
R! warn the
ate
P CLEAut prior oper
KEE witho
ren
only nce
time let child area. les entra
vehic rate
not gate
Do in the is for sepa
nce t use
play
entrans mus
This stria
Pede
Gate Operator (Gate 1)
PVC conduit (not provided) to protect the
power cable and low voltage wire from lawn
mowers and string trimmers.
Wiring
26
PVC conduit at
least 18" below
ground level
(grade)
2
Junction Box
The following items are required to complete the junction box (not provided) installation:
• 4 x 4 Junction Box with 3/4 NPT threaded port holes
• Screws
• PVC Conduit
Open the junction box by removing screws (4) and set aside.
Mount the junction box within 5' of second operator.
Junction Box
(not provided)
Junction Box Cover
Screws (4)
Within 5'
Junction Box
Extension Cable
Gate Operator (Gate 2)
Can
Cau
se
te ath any
g Ga De e at
vin ry or mov
Mo Inju Gate maying. gate or
R! warn the
ate
P CLEAut prior oper
KEE witho
ren
only nce
time let child area. les entra
vehic rate
not gate
Do in the is foruse sepa
nce t
play
entrans mus
This stria
Pede
Control Box
Gate Operator (Gate 1)
Within 5' PVC conduit (not provided) to
protect the power cable and low voltage wire
from lawn mowers and string trimmers.
27
Wiring
3
Connect Watertight Connectors
Route operator cable and extension cable through watertight connector nut and watertight connector. Insert cables
and watertight connectors into the holes in the bottom of the junction box (not provided). Feed extension cable
through PVC conduit and secure with connector nut.
Junction Box (not provided)
Operator
Cable
Watertight Connector
Watertight Connector
Extension Cable
Watertight Connector Nut
Watertight Connector Nut
4
PVC Conduit
Connect Wires in Junction Box
Remove terminals from operator cable. Strip wires and twist like colored wires together with wire nuts.
Wire Nut
Bro
wn
wn
Bro
G
en
re
re
en
G
Operator Cable
White
White
Yellow
Bl
ue
Bl
ue
Yellow
d
R
ed
Re
5
Extension Cable
Secure Junction Box
Put wires inside of junction box. Secure operator and
extension cables with watertight nut. Reinstall cover.
Junction Box
(not provided)
Junction Box
Operator Cable
Screws (4)
Extension Cable
Watertight Connector Nut
Watertight Connector Nut
PVC Conduit
Wiring
28
WARNING
Connect Indoor Transformer to Low Voltage
Wire and Battery
CAUTION
To AVOID damaging gas, power or other underground utility lines,
contact underground utility locating companies BEFORE digging.
• Before digging, contact local underground utility
locating companies.
• Trench and run low voltage (16 AWG) wire for
transformer from control box to an outlet inside the
home or building.
• Run wires through PVC conduit to protect the power
wires from lawn mowers, string trimmers, etc.
NOTE: Calculated using NEC guidelines. Local codes and
conditions must be reviewed for suitability of wire
installation.
AVERTISSEMENT
ATTENTION
e
Caus
Can h
Gate
at any
ng y or Deat
move
MoviInjur may .
or
! Gatewarning gate
the
CLEARprior
operate
KEEPwithout
e
only
time let children
area.
entranc
vehicles e
not gate
Do in the is for separat
e
use
play
entrancmust
This ians
Pedestr
Indoor Outlet
ADVERTENCIA
Insert transformer wires (power wires)
through watertight connector nut.
PRECAUCIÓN
Watertight
Connector Nut
Power Wires
Power
Wires
Indoor Outlet
29
Operator Cable
Wiring
1
Connect indoor Transformer to Control Board
Insert wires from the indoor transformer through the bottom of the control box. Connect wires from the indoor
transformer to AC PWR/SOLAR terminal located on the control board as shown. Plug indoor transformer into a
dedicated outlet. The DIAGNOSTIC LED will blink once every 10 seconds and the STOP LED will light up for 10
seconds.
NOTE: As an alternative to the supplied transformer, a UL listed 12 Volt, up to 30 Watt solar panel with Class 2
output may be used.
P1
R182
C1Ø1
Ø1
C66
J19
K2
C71
C72
C73
C65
C68
J18
LE BUTTON
Z22
L1
DIAGNOSTIC
C75
OFF
C33
LOCK /
BIPART DELAY
GATE 1
CTRL PWR
OVLD
Q6
U4
ON
LOCK
C7Ø
C7
OPEN
C71
Q12
K2
C72
C73
F11
18
SINGLE BUTTON
R93
GATE 1
K1
SET
OPEN
LIMIT
SET
OPEN
SET
CLOSE
LIMIT
RESET
LEARN
LIMITS
TIMER
RUNNING
GATE 2
24V
R9Ø
R9
R1ØØ
R1
ØØ
J2Ø
J2
BR
CTRL PWR
OVLD
STOP
OPEN
R1Ø1
R1
CTRL PWR
WR
SINGLE BUTTON
GR
RESET
OFF
YL
STOP
R186
K4
WH
MAX
OFF
MAX
CTRL PWR
C12
BL
D44
COM
D8
K3
RD
R184
F7
D4
GATE 2
Z4
C13
D2
U3
D16
Q22
D129
R9
F9
R196
F2
MOV1
AC PWR
/SOLAR
C64
R4
3ØA
3 A
3ØA
3 A
30
30
K6
U2 R22
JU2
32V
32V
DB1
MOV1
C2
C11
JU1
J23
J21
R329
R27
F3
C69
R42Ø
R42
R423
D1
J24
F1
CHGR
OVLD
R4
JU1
Indoor Outlet
Control Box
Indoor Transformer
PVC Conduit
30
MOV2
14.5V
Indoor Transformer
Wiring
C2
AC PWR
/SOLAR
JU1
Common
CHGR
OVLD
WARNING
CAUTION
To reduce the risk of FIRE or INJURY to persons use ONLY
Chamberlain part 922GA for replacement batteries.
The batteries are charged in circuit by using the transformer (provided).
Locate the two white battery plugs on the left-hand side of the control box. Connect the plug from the battery to
connector on the control board.
NOTES: Batteries will degrade over time depending on temperature and usage. For best performance, the batteries
should be changed every 3 years.
Batteries do not perform well in extremely cold temperatures. For locations where the temperatures are below -20°C
(-4°F) contact technical support.
AVERTISSEMENT
ATTENTION
Battery Connectors
Board Connectors
Control Board
P1
C66
J19
R182
C1Ø1
C1
Ø1
C65
C68
J18
D36
SOL
Z22
L1
GND
Q6
MAGR
U4
K5
D42
LOCK
ON
LEARN
XMITTER
R2
C75
OFF
C33
Z1
F12
LOCK /
BIPART DELAY
R1
GATE 1
C7Ø
C7
D1Ø
D1
C71
C72
K2
GR
Q12
BR
C73
WH
BL
F11
18
YL
R93
GATE 1
Q1
RD
F8
K1
Battery Connection (GA400D Only)
SET
OPEN
LIMIT
Battery Connectors
SET
CLOSE
LIMIT
LEARN
LIMITS
Z12
Q9
BR
R1ØØ
R1
ØØ
TIMER
RUNNING
GATE 2
R9Ø
R9
CTRL PWR
OVLD
J2Ø
J2
OR
24V
OPEN
R1Ø1
R1
SINGLE BUTTON
GR
RESET
OFF
YL
STOP
R186
K4
WH
MAX
OFF
MAX
COM
ADVERTENCIA
C12
BL
D44
COM
D8
K3
RD
R184
F7
D4
GATE 2
Z4
C13
D2
U3
D16
Q22
D129
R9
F9
R196
F2
MOV1
CHGR
OVLD
AC PWR
/SOLAR
C2
C11
JU1
J23
J21
R329
R27
F3
C69
R42Ø
R42
R423
D1
J24
F1
K6
32V
32V
PRECAUCIÓN
R4
U2 R22
JU2
DB1
MOV2
3
3ØA
A
C64
3
3ØA
A
30
30
2
Connect Batteries
JU1
Board Connectors
Battery Connection (GA420D Only)
31
Wiring
PROGRAMMING
Program Limits
The limits are internal settings that indicate when the gates are in the fully open position and the fully closed position. For
proper functionality, the limits must be learned during the installation process. The programmed limit process uses a
combination of buttons on the control board.
The specific buttons used for programming depends on which side of the gates the control box is mounted on and how
many operators the installation includes. Refer to pages 11-12 to determine if the gate is Left- or Right-handed and for
explanation of PULL-TO-OPEN and PUSH-TO-OPEN.
If a mistake is made during the programming process press the RESET button on the outside of the control box to start
over.
Single Arm Left-Hand Side
Single Arm Right-Hand Side
NOTE: The “Learn Limits” mode can be exited at any time by pressing the RESET button. The mode will time-out
automatically after 60 seconds of inactivity.
Program Open
Program Open
With the gate in the closed position, press the LEARN
LIMITS button (SET OPEN LIMIT LED will blink).
With the gate in the closed position, press the LEARN
LIMITS button (SET OPEN LIMIT LED will blink).
LEARN LIMITS button
LEARN LIMITS button
OPEN EDGE/
R223
P1
CLOSE
EDGE
K6
ALARM
OPEN EDGE/
R223
P1
OPEN EDGE/
Z2Ø
R227
SET
OPEN
LIMIT
Z22
R92
OFF
OPEN
PHOTO
R91
F3
R94
K2
Z8
CLOSE
PHOTO
DIAGNOSTIC
R93
GATE 1
K1 Q9
Z12
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
COM
OVLD
LEARN
LIMITS
DIAGNOSTIC
CONTROL
INPUTS
OPEN
R9Ø
ACCESSORY
POWER
GATE 1
GATE 2
ACCESSORY
OVLD
24V
SET
CLOSE
LIMIT
BRN
TIMER
RUNNING
SINGLE BUTTON
Z8
SET
CLOSE
LIMIT
BRN
SINGLE BUTTON
RESET
TIMER TO
CLOSE
FORCE
R1Ø1
LEARN
LIMITS
TIMER
RUNNING
STOP
COM
R1ØØ
F4
GRN
COM
POWER
10A 32V
GATE 2
WHT
K4
YEL
OFF
MAX
F5
FORCE
BLU
OPEN EDGE/
D21
RED
R35
D9
K3
D8
GATE 2
C12
Z3
F7
Z4
Q22
C13
D22
LOOP
INPUTS
C4
SHADOW
U3
D27
INTERRUPT
C11
Z3
F7
Z4
C13
LOOP
INPUTS
C4
ACCESSORY
OVLD
SHADOW
U3
R4
C2
R196
F6
D9
24 VAC/
SOLAR
INPUT
Z3
Z4
J4
COM
F2
MOV2
R9
MOV1
JMPR2
JMPR1
D2
U2
FUSE
OPEN
BATT 2
BATT 1
D6
DB1
F1 20A 32V
D4
D1
C64
U3
C11
F1 20A 32V
COM
CHGR
OVLD
D15
R35
C12
INTERRUPT
CHGR
OVLD
F6
F2
D27
R9
MOV1
D4
D1
C64
JMPR2
JMPR1
D2
U2
FUSE
OPEN
BATT 2
BATT 1
D6
DB1
R9
MOV1
D4
D1
C64
JMPR1
JMPR2
D2
U2
D6
DB1
R9
CONTROL
INPUTS
OPEN
MAX
D9
C11
MOV2
C11
LEARN
LIMITS
GATE 2
R35
C12
D22
R196
U3
MOV1
SET
CLOSE
LIMIT
ACCESSORY
OVLD
24V
COM
OFF
D21
K3
D8
J4
SET
OPEN
LIMIT
R9Ø
ACCESSORY
POWER
GATE 1
F5
C2
24 VAC/
SOLAR
INPUT
Z4
D27
K1 Q9
Z12
COM
OVLD
DIAGNOSTIC
POWER
K4
Q22
D15
R4
D9
Z3
CLOSE
PHOTO
R93
GATE 1
COM
F4
10A 32V
BLU
RED
R35
R94
K2
DIAGNOSTIC
WHT
GATE 2
D27
C12
Z9
OPEN
PHOTO
R91
F3
D1Ø
OFF
MAGLOCK
STOP
R1ØØ
GRN
YEL
FORCE
Z22
R92
OFF
MAGLOCK
LEARN
XMITTER
R1
10A 32V
RED
U4
ON
RESET
TIMER TO
CLOSE
FORCE
R1Ø1
LEARN
LIMITS
GATE 2
OPEN EDGE/
PHOTO
R224
U4
ON
R2
Z1
BLU
L1
SET
OPEN
LIMIT
Z9
MAGLOCK
LEARN
XMITTER
R1
10A 32V
D1Ø
L1
NC
WHT
YEL
R224
U4
ON
R2
Z1
BLU
RED
OFF
MAGLOCK
Z2Ø
R227
NO
C
GRN
PHOTO
L1
NC
WHT
BRN
K5
NO
C
GRN
K5
MAGLOCK
GATE 1
R2Ø7
NO
C
MAGLOCK
BRN
YEL
U4
ON
R2Ø7
NO
C
CLOSE
EDGE
K6
ALARM
GATE 1
L1
D4
D1
C64
JMPR1
JMPR2
D2
U2
D6
DB1
OPEN EDGE/
ACCESSORY
OVLD
RESET
BUTTON
D27
RESET
BUTTON
Press the GATE 1 right button to move gate to the desired
OPEN position. When gate is in the desired position, press
the LEARN LIMITS button again. Control board will beep.
D27
OPEN EDGE/
Press the GATE 1 left button to move gate to the desired
OPEN position. When gate is in the desired position, press
the LEARN LIMITS button again. Control board will beep.
ACCESSORY
OVLD
D27
DIAGNOSTIC
DIAGNOSTIC
GATE 1
GATE 1
SET
CLOSE
SET
CLOSE
Program Close
Program Close
Press the GATE 1 left button to move gate to the desired
CLOSED position. When gate is in the desired closed
position, press the LEARN LIMITS button again.
When the SET CLOSE LIMIT LED blinks, press the
GATE 1 right button. When gate is in the desired closed
position, press the LEARN LIMITS button.
DIAGNOSTIC
DIAGNOSTIC
GATE 1
GATE 1
SET
CLOSE
SET
CLOSE
The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking,
programming is now complete.
Test the limits by pressing the SBC to open and close the gate.
NOTE: If the SET OPEN LIMIT LED is still blinking, the limits were not programmed successfully. Repeat the
programming making sure the gate is fully opened and closed for each respective limit. If the problem persists, refer to the
Troubleshooting section.
Programming
32
NOTES:
• If one gate is overlapping the other, the gate that is overlapping must be connected to GATE 1 so it will start moving
before the other gate; gate 2 may need to be closed first if there is overlap or a gate lock is being used.
• The programming can be exited at any time by pressing the RESET button. Programming times-out automatically after
60 seconds of inactivity.
Dual Gate (Right-Side Primary Operator)
Dual Gate (Right-Side Primary Operator)
Program Open
Program Open
With the gate in the CLOSED position, press the LEARN
LIMITS button (SET OPEN LIMIT LED will blink).
With the gate in the CLOSED position, press the LEARN
LIMITS button (SET OPEN LIMIT LED will blink).
SET
OPEN
N
T
LIMIT
Press the GATE 1 right button to open the left side
operator.
Press the GATE 1 left button to open the right side
operator.
DIAGNOSTIC
DIAGNOSTIC
GATE 1
GATE 1
SET
CLOSE
SET
CLOSE
Press the GATE 2 right button to move the right side
operator into the OPEN position.
SET
CLOSE
LIMIT
Press the GATE 2 left button to move the left side
operator into the OPEN position.
LE
LIMITS
SET
CLOSE
LIMIT
LE
LIMIT
GATE 2
GATE 2
FORCE
FORCE
Press the LEARN LIMITS button. Control board will beep.
Press the LEARN LIMITS button. Control board will beep.
Program Close
Program Close
When the SET CLOSE LIMITS LED blinks, press the
GATE 2 left button to close the right operator.
When the SET CLOSE LIMITS LED blinks, press the
GATE 2 right button to close the left operator.
SET
CLOSE
LIMIT
SET
CLOSE
LIMIT
LE
LIMIT
GATE 2
FORCE
LE
LIMIT
GATE 2
FORCE
Press the GATE 1 left button to close the left operator.
Press the GATE 1 right button to close the right operator.
DIAGNOSTIC
DIAGNOSTIC
GATE 1
GATE 1
SET
CLOSE
SET
CLOSE
Press the LEARN LIMITS button.
Press the LEARN LIMITS button.
The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking,
programming is now complete.
Test the limits by pressing the SBC to open and close the gate.
NOTE: If the SET OPEN LIMIT LED is still blinking, the limits were not programmed successfully. Repeat the
programming making sure the gate is fully opened and closed for each respective limit. If the problem persists, refer to the
Troubleshooting section.
33
Programming
Force/Timer to Close/Party Mode Controls
WARNING
Force Adjustment
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing gate.
• Too much force on gate will interfere with proper operation
of safety reversal system.
• NEVER increase force beyond minimum amount required to
close gate.
• NEVER use force adjustments to compensate for a binding or
sticking gate.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Gate MUST reverse on contact with a rigid
object.
The operator is equipped a with an obstruction sensing
feature. If the gate encounters an obstruction the operator
will automatically reverse direction and stop. Based on the
length and weight of the gate it may be necessary to make
force adjustments. The force adjustment should be high
enough that small objects such as branches or wind will
not cause nuisance interruptions but low enough to prevent
serious injury to a person or a vehicle.
To adjust the force:
Using the 3-button remote or the Single Button Control
(SBC) button on the control board, open and then close
the gate.
If the gate stops and or reverses before reaching the fully
open or closed position increase the force by turning the
force control slightly. Run operator through a complete
cycle.
CAUTION
Party ModeAVERTISSEMENT
TTC can be temporarily disabled by pressing RESET
button (located on the outside side of the control box)
when the gate is fully open. This will allow the gate to
remain open until another command is received. Following
this command, TTC is re-enabled at the previously set
time period.
NOTE: Weather conditions can affect the gate
movement, so seasonal adjustment may be required. The
force control is factory set to the mid position.
ATTENTION
FORCE
Maximum Force
OPEN EDGE/
R223
P1
Minimum Force
CLOSE
EDGE
K6
ALARM
R2Ø7
NO
K5
PHOTO
NO
BRN
L1
R224
C
GRN
Timer-to-Close (TTC)
Z2Ø
R227
LEARN
XMITTER
C
MAGLOCK
GATE 1
Z22
R92
U4
NC
WHT
ON
R2
Z1
Z9
OPEN
PHOTO
R1
YEL
10A 32V
BLU
R91
F3
RED
D1Ø
GATE 1
TIMER TO
CLOSE
R94
K2
Z8
FORCE
CLOSE
PHOTO
DIAGNOSTIC
R93
The TIMER TO CLOSE feature can be set to
automatically close the gate after a specified time period.
If the TTC is set to the OFF position, then the gate will
remain open until the operator receives another
command from a remote control or SBC.
To set the TIMER TO CLOSE:
Rotate the TIMER TO CLOSE dial to the desired setting.
The range is 0 to 180 seconds, 0 seconds is OFF.
NOTE: Any radio command, SBC, or CLOSE command
on the control board prior to the TTC expiring will close
the gate. The TTC is reset by any signals from the loops,
close edges, and close safety sensors (IR’s).
GATE 2
ACCESSORY
POWER
K1 Q9
Z12
BRN
TIMER TO
CLOSE
FORCE
R9Ø
COM
OVLD
GRN
ACCESSORY
OVLD
24V
WHT
CONTROL
INPUTS
OPEN
R1Ø1
YEL
BRN
BLU
R1ØØ
SINGLE BUTTON
F4
GRN
RED
WHT
GATE 2
Z9
RESET
10A 32V
STOP
OFF
YEL
MAX
COM
BLU
COM
POWER
R35
RED
Z8
D9
K3
D8
GATE 2
C12
Z3
F7
Z4
Q22
C13
D22
LOOP
INPUTS
C4
SHADOW
U3
OFF
MAX
INTERRUPT
C11
ADVERTENCIA
C2
R196
F6
24 VAC/
SOLAR
INPUT
J4
COM
CHGR
OVLD
D15
R4
F2
MOV2
MOV1
R9
F1 20A 32V
D4
D1
BATT 2
BATT 1
D4
D2
PRECAUCIÓN
TIMER TO
CLOSE
OFF
MAX
34
Programming
To Add or Reprogram a Remote Control
(not provided)
WARNING
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate
or door.
1. Press LEARN XMITTER button and release (LED will
light up).
2. Press remote button, the LED will flash, alarm output
will activate twice.
3. Repeat steps 1 and 2 until all remote controls are
programmed (9 remote controls maximum).
NOTE: For highest level of security, we recommend the
Security✚® line of products. Refer to Accessories.
CAUTION
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
AVERTISSEMENT
ATTENTION
To Add a Wireless Keyless Entry
(not provided)
Remote Control LEARN XMITTER Button
1. Press LEARN XMITTER button and release (LED will
light up).
2. Enter a four digit personal identification number (PIN)
of your choice on the keypad.
3. Then press ENTER, the LED will flash, alarm output
will activate twice.
OPEN EDGE/
R223
P1
CLOSE
EDGE
K6
ALARM
R2Ø7
NO
Z2Ø
R227
LEARN
XMITTER
C
K5
MAGLOCK
LEARN
XMITTER
R1
GATE 1
PHOTO
NO
BRN
L1
R224
C
GRN
Z22
R92
U4
NC
WHT
ON
R2
Z1
Z9
OPEN
PHOTO
R1
YEL
10A 32V
BLU
R91
F3
RED
D1Ø
GATE 1
R94
K2
Z8
CLOSE
PHOTO
DIAGNOSTIC
R93
GATE 2
ACCESSORY
POWER
K1 Q9
Z12
BRN
TIMER TO
CLOSE
FORCE
R9Ø
COM
OVLD
GRN
ACCESSORY
OVLD
24V
WHT
CONTROL
INPUTS
OPEN
R1Ø1
YEL
BRN
BLU
R1ØØ
RED
SINGLE BUTTON
F4
GRN
RESET
10A 32V
WHT
GATE 2
STOP
OFF
YEL
MAX
COM
BLU
COM
POWER
R35
RED
D9
K3
D8
GATE 2
C12
Z3
F7
Z4
Q22
C13
D22
LOOP
INPUTS
C4
SHADOW
U3
INTERRUPT
C11
CHGR
OVLD
D15
ADVERTENCIA
R4
C2
R196
24 VAC/
SOLAR
INPUT
J4
OPEN
MOV2
MOV1
R9
COM
F6
F2
F1 20A 32V
D4
PRECAUCIÓN
To Erase All Codes
To deactivate any unwanted remote controls or keyless
entries, first erase all codes:
Press and hold the LEARN XMITTER button on control
board until the learn indicator light goes out (approximately
6 seconds). All previous codes are now erased.
Reprogram each remote control or keyless entry you wish
to use.
Make sure the rubber seal around the cover is intact and close the cover. Secure the control box cover with screws (4).
Installation is complete.
35
Programming
OPERATION AND MAINTENANCE
G
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
MENT
N
NCIA
ÓN
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. NEVER let children operate or play with gate controls. Keep
the remote control away from children.
3. ALWAYS keep people and objects away from the gate. NO
ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
4. Test the gate operator monthly. The gate MUST reverse on
contact with a rigid object or stop when an object activates
the non-contact sensors. After adjusting the force or the
limit of travel, retest the gate operator. Failure to adjust and
retest the gate operator properly can increase the risk of
INJURY or DEATH.
5. Use the emergency release ONLY when the gate is not
moving.
6. KEEP GATES PROPERLY MAINTAINED. Read the owner’s
manual. Have a qualified service person make repairs to
gate hardware.
7. The entrance is for vehicles ONLY. Pedestrians MUST use
separate entrance.
8. Disconnect ALL power BEFORE performing ANY
maintenance.
9. SAVE THESE INSTRUCTIONS.
AVERTISSEMENT
Using Your Gate Operator
AVERTISSEMENT
Your operator will operate with up to nine Security✚®
remote controls and one Security✚® Keyless Entry System.
If you purchase a new remote, or if you wish to deactivate
any remote, follow the instructions in the Programming
section.
Activate your operator with any of the following:
Hand Held Remote Control (See Accessories): Hold
push button down until the gate begins to move. While gate
is moving, the next command sent from the remote will stop
the gate. Next command will reverse the gate direction.
Keyless Entry (See Accessories): If provided with your
gate operator, it must be programmed before use. See
Programming.
Vehicle Exit Sensor: See accessory page.
Automatic Timer To Close Feature
TIMER TO
CLOSE
The Timer-To-Close (TTC) Feature comes
from the factory in the OFF setting.
The “TIMER RUNNING LED” will flash once
for every second of adjusted time. The gate(s)
OFF
must fully open for the timer feature to be
MAX
active and close the gate(s). Any radio
command or pressing the single button on the control
board prior to the TCC time expiring will close the gate.
The TTC is reset by any signals from the loops, close
edges, and close safety sensors (IR’s).
Party mode
Entrapment Features
When the operator is activated (with the safety sensors
correctly installed and aligned) and the safety sensors
encounter an obstruction, the following will occur:
Opening Cycle: Gate will stop, reverse direction for
approximately 2 seconds and then stop. The next
command will continue the gate in the close direction.
Closing Cycle: Gate will stop, reverse direction for
approximately 2 seconds and then stop. The next
command will open the gate.
If the Timer-to-Close feature is enabled and you would like
the gate to remain open, simply push the reset button
(located on the outside of the control box). The next
command given to the operator will close the gate and
return the operator to normal operation.
ADVERTENCIA
ADVERTENCIA
Alarm Sounds
The operator alarm will sound under the following condition:
If gate encounters two consecutive obstructions, the
operator will stop, the alarm will sound (up to 5 minutes)
and the control board will require resetting. Reset the
control board by pressing the “Reset Button” located on the
outside of the control box. No commands at this time will
operate gate. After the operator is reset, normal functions
will be available.
Operation and Maintenance
36
Sleep mode (battery conservation)
Sleep Mode (Battery Conservation): The operator enters
sleep mode 10 seconds after the last command is given.
The diagnostic LED will blink in this mode. The safety
sensors (photo eyes) indicator LEDs will not be on. The
next operation command will return
the operator to normal operation.
RESET
RESET
Manual Release
In case of a power failure, the operator can be disengaged from the gate. Follow the directions below to disconnect and
reconnect the operator to the gate.
Release
1. Remove the hairpin clip and release pin that secures the gate bracket to the gate.
2. Move operator away from gate and out of the way of gate travel.
If a gate lock (automatic or manual) is used; disengage the lock.
Engage
1. Align the hole in the arm with the hole in the gate bracket.
2. Insert release pin and secure with hairpin clip.
Release Pin
Gate Bracket
Hairpin Clip
Maintenance
Description
Entrapment
Protection Systems
Manual Release
Gate
Accessories
Electrical
Mounting Hardware
Batteries
Total Unit
CHECK AT LEAST ONCE EVERY
Task
Check for proper operation
1 Month 3 Months
●
●
Check and operate
Inspect for wear or damage
Check all for proper operation
Inspect all wire connections
Check for tightness
Replace
Inspect for wear or damage
NOTES:
1. Disconnect power before servicing.
2. Severe or high cycle usage will require more frequent
maintenance checks.
3. Inspection and service should always be performed
anytime a malfunction is observed or suspected.
4. When servicing, please do some “house cleaning” of the
operator and the area around the operator. Pick up any
debris in the area. Clean the operator as needed.
6 Months
●
12 Months
●
●
●
●
●
●
●
●
●
●
●
●
●
3 Years
●
●
●
●
●
●
●
●
5. It is suggested that while at the site voltage readings be
taken at the operator. Using a Digital Voltmeter, verify
that the incoming voltage to the operator it is within ten
percent of the operator’s rating.
6. See page 34 for instructions on how to check gate force
and sensitivity adjustments.
37
Operation and Maintenance
Wiring Diagram
To protect against fire and electrocution:
To protect against
fire and
electrocution:
• DISCONNECT
power
and
battery BEFORE installing or
• DISCONNECT
power and battery BEFORE installing or servicing operator.
servicing
operator.
For continuedprotection
protection against
fire: fire:
For continued
against
•
Replace
ONLY
with
fuse
of
same
type and
rating.
• Replace ONLY with fuse of same
type
and rating.
* Class 2 circuit 15 v maximum output
2. Close edge
17. Learn Xmitter
Primary Gate Jog
3. Open edge/photo 18.
eye
19. Learn Limits
4. Open photo eye 20. Secondary Gate Jog
21. Force
5. Close photo eye 22. Timer To Close
23. Receiver Module
6. Control inputs
24. Fuses (20 Amp)
7. Loop inputs
10. Accessory power
12. Automatic gate lock
13. Fault alarm
9. Gate 2
10. Accessory Power*
11. Gate 1
12. Lock (Solenoid/Maglock) Output*
13. Alarm Output*
14. Battery 1 Connector
15. Battery 2 Connector
16. Lock/BiPart Delay
*Class 2 circuit 15 V maximum output
1. Antenna Input
2. Close Edge*
3. Open Edge/Photo*
4. Open Photo*
5. Close Photo*
6. Control Inputs*
7. Loop Inputs*
8. AC PWR/SOLAR
Fault Alarm
23
P1
R182
C1Ø1
C66
J19
13 *
Automatic Gate Lock
(optional)
1
CLOSE
EDGE
C65
2*
ALARM
BLK
EDGE
D36
C68
J18
12 * RED
ACCESSORY
0VLD
RED
OPEN EDGE/
PHOTO
SOL
Z22
BLK
GND
U4
LEARN
XMITTER
R2
LOCK /
BIPART DELAY
C7Ø
D1Ø
BRN
4*
916GA SAFETY SENSORS
CLOSE
PHOTO
5*
916GA SAFETY SENSORS
C73
BL
GATE 1
R93
19
Q1
RED
F11
18
18
DIAGNOSTIC
YL
BLU
Q12
WH
YEL
C72
17
K2
GR
WHT
RD
SET
OPEN
LIMIT
K1
F8
SET
CLOSE
LIMIT
LEARN
LIMITS
Z12
Q9
ACCESSORY
POWER
TIMER
RUNNING
GATE 2
20
BRN
BR
GRN
FORCE
R9Ø
R1ØØ
R1Ø1
21
MAX
RESET
STOP
STOP
R186
OFF
YL
OFF
MAX
CTRL PWR
C12
BL
D44
D8
CTRL PWR
K3
RED
SINGLE BUTTON (SBC)
22
K4
YEL
OPEN (EXI T LOOP)
RESET
WH
BLU
CONTROL
INPUTS
OPEN
SINGLE BUTTON
GR
WHT
CTRL PWR
OVLD
SINGLE BUTTON
TIMER TO
CLOSE
J2Ø
12 V
9
RD
R184
F7
D4
GATE 2
Z4
SHADOW
R9
F9
R196
F2
INTERRUPT LOOP
CTRL PWR
AC PWR
/SOLAR
7
C2
C11
JU1
MOV1
CHGR
OVLD
*
R4
U2 R22
JU2
32V
32V
DB1
NOTE: Batteries MUST
be connected to operate.
MOV2
2Ø
K6
C64
3ØA
3ØA
30
14
C69
R42Ø
R423
R329
R27
J23
J21
15
F3
SHADOW LOOP
INTERRUPT
D1
J24
F1
6*
LOOP
INPUTS
C13
D2
U3
D16
Q22
D129
24
OPEN
PHOTO
16
C71
BR
GRN
Gate 2 (Second)
OPTIONAL GROUND ROD
8
OR OPTIONAL SOLAR PANEL
RED
BLK
NOTE: For all installations use
the 14.5V output on transformer.
Operation and Maintenance
OR
C75
OFF
R1
GATE 1
10 *
F12
Z1
ON
C33
11
Gate 1 (Master)
K5
D42
916GA SAFETY SENSORS
EDGE
Q6
MAGR
LOCK
3*
38
Diagnostic Chart
Your gate operator is programmed with self-diagnostic capabilities. The diagnostic LED will flash a number of times then
pause signifying it has found a potential issue. Consult Diagnostic Chart below.
1 FLASH
Normal Operation
Power ON
2 FLASHES
STOP not connected
3 FLASHES
Low Battery Voltage
4 FLASHES
Low Battery
Capacity
5 FLASHES
RPM Reversal Gate 1
or Arm Disconnected
6 FLASHES
Force Reversal Gate 1
7 FLASHES
RPM Reversal Gate 2
or Arm Disconnected
8 FLASHES
Force Reversal Gate 2
9-11 FLASHES
Potential chip failure
Stop is not connected.
• Press the RESET button and make sure the STOP LED turns on.
• Check to make sure the jumper wire is connected between the COM and STOP input
on the control board. Stop is a normally closed input.
Battery voltage is below the recommended operating level.
• Battery may not be properly charged. Disconnect all batteries and make sure AC
power or solar power is connected. Verify AC power outlet.
• Verify that the battery fuses are intact and not blown. Replace blown fuses with same
type and rating.
• Batteries are no longer capable of holding a charge due to age or excessive depleting
of the battery. Replace the batteries (see accessories page). Dispose of old batteries
properly.
Battery voltage is below the recommended operating level.
• Battery may not be properly charged. Disconnect all batteries and make sure AC
power or solar power is connected. Verify AC power outlet.
• Verify that the battery fuses are intact and not blown. Replace blown fuses with same
type and rating.
• Batteries are no longer capable of holding a charge due to age or excessive depleting
of the battery. Replace the batteries (see accessories page). Dispose of old batteries
properly.
Gate 1 has encountered an obstruction or the arm is disconnected.
• Make sure the path of the gate is clear and the gate moves freely.
• Incorrect or poor connection to Gate 1 arm. Check the green and white wires on the
motor arm to make sure connections are correct and secure.
• Bad arm or control board. Press the LEARN LIMITS button and press the GATE 1
buttons to move the arm. If the arm does not move continuously, disconnect arm from
Gate 1 and connect the arm to the Gate 2 connector and repeat the attempt to move
the arm. If the arm does not move continuously on either Gate 1 or 2, replace the arm.
Gate 1 has encountered an obstruction.
• Make sure the path of the gate is clear and the gate moves freely.
• If there is no obstruction the force adjustment is set too low. Increase the force setting
and verify that the gate moves without reversing and will reverse if an obstruction is
encountered.
Gate 2 has encountered an obstruction or the arm is disconnected.
• Make sure the path of the gate is clear and the gate moves freely.
• Incorrect or poor connection to Gate 2 arm. Check the green and white wires on the
motor arm to make sure connections are correct and secure.
• Bad arm or control board. Press the LEARN LIMITS button and press the GATE 2
buttons to move the arm. If the arm does not move continuously, disconnect arm from
Gate 2 and connect the arm to the Gate 1 connector and repeat the attempt to move
the arm. If the arm does not move continuously on either Gate 1 or 2, replace the arm.
Gate 2 has encountered an obstruction.
• Make sure the path of the gate is clear and the gate moves freely.
• If there is no obstruction the force adjustment is set too low. Increase the force setting
and verify that the gate moves without reversing and will reverse if an obstruction is
encountered.
Potential RAM, Flash, or EEPROM failure.
• Turn power off and on.
• If problem does not resolve itself by turning power off and on, replace the control
board.
39
Operation and Maintenance
Troubleshooting
SYMPTOM
POSSIBLE SOLUTION
Operator does not run.
Diagnostic LED not on.
• Power not connected. Make sure the AC/Solar input is connected and that at least
one battery is connected with the corresponding fuse intact.
• Low or defective battery. Check the battery to make sure that the red wire goes to
the positive terminal of the battery and the black wire goes to the negative terminal
of the battery. Replace the battery if the open circuit voltage is below 11.5Vdc.
• Bad control board. Call technical support for more options.
• Low or defective battery. At least one charged battery must be connected for the
unit to operate. Verify the battery fuse is intact. Check battery connections and
battery voltage to be above 11.5V Replace batteries if necessary.
• STOP button connection loose or disconnected. Press the RESET button and verify
that the STOP LED lights up and then turns off after 10 seconds. Verify the wire
connects between the STOP and CTRL PWR terminals.
• Obstruction blocking safety sensors. Press the RESET button and verify that all the
safety LEDs (OPEN EDGE/PHOTO, OPEN PHOTO, CLOSE PHOTO) are OFF. If
any are ON, clear any obstructions and verify the LED turns off
NOTE: The RESET button may need to be hit multiple times since the LEDs turn
off after 10 seconds when the unit goes to sleep.
• (Optional Accessory) Safety edge is damaged or on an obstruction. Press the
RESET button and verify that the Safety LEDs (OPEN EDGE and CLOSE EDGE/
PHOTO) are OFF. If either is ON, clear any obstructions and verify the LED turns
off.
NOTE: The RESET button may need to be hit multiple times since the LEDs turn
off after 10 seconds when the unit goes to sleep.
• (Optional Accessory) Interrupt loop or Shadow loop is obstructed. Press the RESET
button and verify that the INTERRUPT and SHADOW LEDs are OFF. If either is on,
check the loop detector and its wiring to insure that it is not incorrectly being
triggered.
• Bad control board. Call technical support for help with replacement parts.
• Battery not connected. At least one charged battery must be connected for the unit
to operate. Verify battery fuse is intact. Check battery connections and battery
voltage to be above 11.5V. Replace batteries if necessary.
• Arm cable loose or disconnected. Verify that all of the wires, especially the red and
blue wires, going to the arm are secure and that the connector is properly mated to
the header.
• Arm is jammed or incorrectly installed. Disconnect the motor housing from the arm
and verify that the arm moves freely. With the motor housing still disconnected,
enter the Learn Limits mode and verify that the motor spins. Reconnect the motor
housing to the arm and make sure that all 4 screws are securely tightened and that
the motor seats correctly against the worm drive. Relearn limits for the operator.
• Bad control board. Call technical support for help with replacement parts.
Operator powers up but
does not run.
Relays “click” when remote
control or single button
control (SBC) command
is given, but the operator
does not move.
Operation and Maintenance
40
SYMPTOM
POSSIBLE SOLUTION
The arm moves but cannot
exit Learn Limits mode.
Cannot learn limits.
• Arm does not extend or contract enough during travel. The arm piston must extend
and contract close to its full length to Learn Limits. Adjust the arm mounting so that
this can be achieved.
• Motor cable wire not connected. Make sure that all the motor wires are connected
properly.
• Motor housing is not properly seated. Make sure that the motor housing for the
arm(s) is properly seated so there are no gaps between the motor housing and arm
assembly. Make sure all 4 screws are tightened.
• Over extending or contracting arm. Disconnect the motor housing from the arm and
make sure that the arm moves freely throughout the full length of travel. Adjust arm
mounting and positioning if necessary.
• Arm is interfering with the gate mount bracket. Examine the hinge point where the
arm mounts to the gate post. Make sure that the arm housing does not hit or
interfere with the gate post or mounting bracket throughout the full length of travel.
Adjust the arm mounting and positioning if necessary.
• Gate is excessively heavy or hinges are bad. Verify that the gate is within the ratings
for this product. Disconnect the arms and verify that both gates swing easily.
Lubricate or replace hinges as necessary.
• Battery not connected. At least one charged battery must be connected for the unit
to operate. Verify the battery fuse is intact. Check battery connections and battery
voltage to be above 11.5V. Replace batteries if necessary.
• STOP button connection loose or disconnected. Press the RESET button and verify
that the STOP LED lights up and then turns off after 10 seconds. Verify the wire
connects between STOP and CTRL PWR terminals.
• Single Button Control (SBC) button connection loose. Check wiring for SBC button.
Use the on-board single button to verify operator will respond.
• Bad control board. Call technical support for help with replacement parts.
• Battery not connected. At least one charged battery must be connected for the unit
to operate. Verify battery fuse is intact. Check battery connections and battery
voltage to be above 11.5V. Replace batteries if necessary.
• STOP button connection loose or disconnected. Press the RESET button and verify
that the STOP LED lights up and then turns off after 10 seconds. Verify the wire
connects between the STOP and CTRL PWR terminals.
• Radio module not plugged in. Verify the green Radio module (located next to the
coaxial connector) is properly mated with both 4-pin connectors.
• Antenna not connected. Verify the antenna and coaxial cable are properly
connected to the control board.
• Transmitter not learned. Refer to Programming Remote Control section for steps to
program the transmitter.
• Bad control board. Call technical support for help with replacement parts.
• Obstruction sensed. Check safety devices and gate for obstructions.
• A fault has occurred. Check Diagnostic LED for possible error codes.
• Force set too low. Adjust FORCE setting until gate completes a full open/close cycle
without reversing. The force setting may need to be adjusted in cold weather, as the
gate will not move freely.
• Loops are reversed. Make sure that the Safety loop and Shadow loop are
connected properly. The gate may trigger the Shadow loop as it moves, so it must
be connected to the correct input.
• Low or defective battery. At least one charged battery must be connected for the
units to operate. Verify battery fuse is intact. Check battery connections and battery
voltage to be above 11.5V. Replace batteries if necessary.
Gate does not fully open or
close when trying to learn
limits.
Unit does not respond to
single button control (SBC)
command.
Unit does not respond to
remote control command.
Gate stops and reverses
immediately after it starts
moving.
41
Operation and Maintenance
SYMPTOM
POSSIBLE SOLUTION
Gate opens but does not
close.
• An open input is continuously activated. Check the open loop or vehicle probe to
make sure they are clear of objects. Verify connections and operation for these
devices.
• Low battery. Measure the voltage across the battery. Voltage should be above
11.5Vdc. Replace battery if required.
• (Optional Accessory) Entry system output is connected to the OPEN input, and is
“stuck” opening. Verify entry system connections and operations.
• Obstruction blocking close photo eyes, shadow loop, or safety loop. Check eyes for
alignment and verify all connections and operation for safety devices.
• (Optional Accessory) Close safety edge is damaged or on an obstruction. Verify
operation and connection of close edge.
• Verify that the Timer to Close is ON and adjusted to desired delay.
• Gate opened by a force obstruction reversal. Check the Diagnostic LED and clear
gate path of any obstructions.
• The Interrupt loop or Shadow loop is obstructed (optional accessories).
• Obstructed close safety sensor or safety edge (optional accessory). Check
connections and operations of safety devices.
• Low battery. Measure the voltage across the battery. Voltage should be above
11.5Vdc. Replace battery is required.
• An open input is continuously activated. Check the open loop or vehicle probe to
make sure they are clear of objects. Verify connections and operation for these
devices.
• (Optional Accessory) Entry system output is connected to the OPEN input, and is
“stuck” opening. Verify entry system connections and operation.
• Operator in “Party” mode after RESET button pressed while at the OPEN limit. Use
a remote or the SBC to close the gate and reopen it. Verify that the
TIMER RUNNING LED is flashing.
• Double entrapment occurred. Two successive obstructions were encountered while
moving the gate. Press the RESET button and ensure that the gate path is clear of
all obstructions. Check the FORCE setting to make sure it is properly set.
Gate does not close
automatically with Timer to
Close enabled.
Alarm constantly sounds
for 5 minutes. Sounds
whenever a command is
issued.
Alarm is beeping 3 times on
a command.
Gate runs too slow.
Gate 2 closes before Gate 1.
Alarm beeps when running.
Gate does not open/close at
the same place each time.
Operation and Maintenance
• Low battery. Measure the voltage across the battery. Voltage should be above
11.5Vdc. Replace battery if required.
• Open and Close Limits are set too close together. If the Open and Close Limits are
set within the ramp down distance of each other, the gate will run at slow speed all
the time.
• The gate is starting within the ramp down distance from the Open or Close Limit.
Gate will run slow to limits if motion is started within the ramp-down distance from
the limit.
• Lock/Bipart Delay not set. Slide the Lock/Bipart Delay switch to ON. Verify that
Gate 1 starts moving first on open and last on close.
• Gate is excessively heavy or hinges are bad. Verify that the gate is within the ratings
for this product. Disconnect the arms and verify that both gates swing easily.
Lubricate or replace hinges as necessary.
• Gate is unbalanced. Disconnect the arms and verify that both gates swing easily in
both directions. If the gates are harder to move in one direction verses the other, the
gate is not properly balanced and the hinges must be adjusted.
• Bad motor connection. Check the motor wires and connections for possible loose or
corroded terminals.
• Low battery. Measure the voltage across the battery. Voltage should be above
11.5Vdc. Replace battery if required.
• In windy areas, an automatic gate lock for close and a hard stop for open is
recommended to ensure the gate stops in the same place each time.
• Periodic limit adjustments may be necessary.
42
Repair Parts
Control Box
3
4
6
2
1
5
ITEM
1
2
3
4
5
6
PART #
K1A6426
K23-19380
K74-34392
922GA
K204B0195
K29-20095
K74-33975
K1A5747
K1A5747-2
DESCRIPTION
QTY
Control Board with
Mounting Bracket
1
Reset Switch
1
Antenna
1
Battery with Harness
1
Indoor Transformer
1
Alarm
1
Not Shown
Complete Control Box (without battery) 1
Receiver Module - 315MHz
1
Receiver Module - 390MHz (optional)
1
NOTE: The fuse is a standard 20 Amp fuse that is available from your local
automotive store.
43
Operation and Maintenance
Repair Parts
Gate Operator Arm
1
2
ITEM
1
2
PART #
DESCRIPTION
K-41ADBL-0004
K-LA-6
Arm Cover
Complete Arm Assembly
Includes: Arm, Motor and
Plastic Cover
Not Shown
Hardware Kit
Includes: One Extension
Bracket, One Gate Bracket,
One Post Bracket and
One Hardware Bag)
Owner’s Manual
Owner’s Manual - Spanish
Screws for housing (pack of 4)
K-DBL-0095SA
01-33859
01-33859SP
K-41ADBL-1011SA
Operation and Maintenance
44
QTY
1
1
1
1
1
Accessories
OPEN
CLOSE
®
953D
940D
3-Button SECURITY✚ Remote
Control:
Includes visor clip.
OPEN
Protector System® Safety Sensors:
The Safety Sensors are intended
for installation with the operators
covered in this manual. To order call:
1-866-826-4943 or visit our website
www.chamberlain-diy.com.
916GA
OPEN
7
915GA
917GA
918GA
OPEN
OPEN
956D
SECURITY✚® Keyless Entry:
Enables homeowner to operate gate
operator from outside by entering a
four digit code on a specially designed
keyboard.
3-Button Mini-Remote Control with
SECURITY✚ :
With key ring and fastening strip.
®
914GA
Gate Arm Pin Lock:
The pin lock kit is designed to prevent
disconnection of the gate operator and
the gate while providing a means to
open the gate in case of power failure.
921GA
Vehicle Exit Sensor:
One piece outdoor buried vehicle
motion detector with sensing probe is
housed in a small relay type housing
so it is easy to integrate with gate,
providing for free exit only.
Low Voltage Wire (250')
Low voltage wire is required to connect
the transformer to the control box. Also
can be used to connect optional safety
sensors to the control box. UL
approved for burial.
919GA
Push-To-Open Bracket:
Used to allow the gate operator to
push the gate open.
Wireless Gate Doorbell
922GA
Automatic Gate Lock:
Solenoid-driven lock that automatically
unlocks when gate is open and locks
when gate is closed. Can be mounted
onto gate or post. Can be released in
case of emergency.
Low Voltage Wire (100')
Low voltage wire is required to connect
the transformer to the control box. Also
can be used to connect optional safety
sensors to the control box. UL
approved for burial.
OPEN
OPEN
CLOSE
CLOSE
OPEN
CLOSE
920GA
PRESS
TO
R ING
Allows guests to ring a doorbell
in the house from the keypad.
Homeowner can open gate
from inside the home using the
included remote control button.
No wiring required. Keypad can
be programmed to allow access to
selected guests using a 4 digit code.
Gate Access System Battery
The Gate Access System Battery is
designed to add a battery for solar
applications or as a replacement
battery (includes cable harness).
OPEN
CLOSE
45
Operation and Maintenance
WARRANTY POLICY
CHAMBERLAIN ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first retail purchaser of this product, for the structure in which this product is originally
installed, that it is free from defect in materials and/or workmanship for a period of ONE year from the date of purchase. The proper
operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and
testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety.
If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-866-826-4943,
toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You
will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-ofpurchase receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt
by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no
cost to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole
option.
ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE ONE YEAR LIMITED
WARRANTY PERIOD SET FORTH ABOVE, AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some
States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS
LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION
OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY
MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A
REPAIRED OR REPLACED UNIT, OR REPLACEMENT OF BATTERIES.
THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE HARDWARE,
INCLUDING BUT NOT LIMITED TO THE GATE SPRINGS, GATE ROLLERS, GATE ALIGNMENT OR HINGES. THIS LIMITED
WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE
PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN
CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF
WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED
HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS
PRODUCT.
Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or
exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
HOW TO ORDER REPAIR PARTS
OUR LARGE SERVICE ORGANIZATION SPANS AMERICA
INSTALLATION AND SERVICE INFORMATION
CALL OUR TOLL FREE NUMBER
1-866-826-4943
www.chamberlain.com
WHEN ORDERING REPAIR PARTS
PLEASE SUPPLY THE FOLLOWING INFORMATION:
PART NUMBER DESCRIPTION MODEL NUMBER
ADDRESS ORDER TO:
THE CHAMBERLAIN GROUP, INC.
Technical Support Group
6050 S. Country Club Road
Tucson, AZ 85706
Warranty
46
NOTES
47
Notes
2
3
4
5
53/4"
TEMPLATE FOR POST BRACKET MOUNTING
1
53/4"
5
01-33859D
4
3
2
© 2009, The Chamberlain Group, Inc.
All Rights Reserved
1