Chamberlain 5580A-2GB Garage Door Opener User Manual

Instructions – Garage Door Operator Model 5580A-2GB
INT
Int. Service(+49) 6838/907 172
www.iftmaster.de
1-en
Warning
Start by reading These Import Safety Instructions
Failure to comply with the following instructions may result in serious personal injury or property damage.
• Read these instructions carefully
• The garage door opener is designed and tested to offer reasonable safe service provided it is installed and
operated in strict accordance with the instructions in this manual.
These safety alert symbols mean Caution – a personal safety or property damage instruction. Read these instructions
carefully.
WARNING: If your garage has no service entrance door, Model 1702E Outside Quick Release must be installed. This accessory
allows manual operation of the garage door from outside in case of power failure.
Keep garage door balanced. Sticking or binding doors
must be repaired. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under extreme
tension and can cause serious personal injury. Do not
attempt to loose, move or adjust them. Call for garage
door service.
Do not wear rings, watches or loose clothing while
installing or servicing a garage door opener.
To avoid serious personal injury from entanglement,
remove all ropes connected to the garage door
before installing the door opener.
Installation and wiring must be in compliance with your
local building and electrical codes. Connect the power
supply cord only to properly earthed mains.
Lightweight doors of fiberglass, aluminum or steel
must be substantially reinforced to avoid door
damage. (See page 4.) The best solution is to check
with your garage door manufacturer for an opener
installation reinforcement kit.
The safety reverse system test is very important.
Your garage door MUST reverse on contact with a
40mm obstacle placed on the floor. Failure to properly
adjust the opener may result in serious personal injury
from a closing garage door. Repeat the test once a
month and make any needed adjustments.
This unit should not be installed in a damp or wet
space.
Door must not extend over public byway during
operation.
Contents
Page
Illustration
The force, as measured on the closing edge of the
door, should not exceed 400 N (40kg). If the closing
force is more than 400 N, the Protector System must
be installed. Do not use the force setting procedure
to compensate for a binding or sticking garage door.
Excessive force will interfere with the proper operation of
the Safety Reverse System or damage the garage door.
Permanently fasten the caution label adjacent to the
lighted door control button as a reminder of safe
operating procedures.
Disengage all existing garage door locks to avoid
damage to garage door.
Install the lighted door control button (or any additional
push buttons) in a location where the garage door is
visible, at a height of at least 1,5m and out of the
reach of children. Do not allow children to operate
push button(s) or remote control(s). Serious personal
injury from a closing garage door may result from misuse
of the opener.
Activate opener only when the door is in full view,
free of obstructions and opener is properly adjusted.
No one should enter or leave the garage while the
door is in motion. Do not allow children to play near
the door.
Use manual release only to disengage the trolley and, if
possible, only when the door is closed. Do not use the
red handle to pull the door open or closed.
Disconnect electric power to the garage door opener
before making repairs or removing covers.
This product is provided with a power supply cord of
special design which, if damaged, must be replaced by
a power supply cord of the same type; such a power
supply cord may be obtained from your local LiftMaster
distributor and must be fitted by a specialist.
Programming your Opener & Remote . . 5 . . . . . . . . . . . . . . . 22
Program your Keyless Entry . . . . . . . . . .5 . . . . . . . . . . . . . . .23
Safety Rules . . . . . . . . . . . . . . . . . . . . . . . 1
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . 24-26
Before you Begin . . . . . . . . . . . . . . . . . . . 1
Install the Protector System™
Door Types . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . 1
(Optional) . . . . . . . . . . . . . . . . . . . . . . . . . 7 . . . . . . . . . . . . 27
Tools Required . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . 2
Special Features of the 5580-2GB . . . . . .7 . . . . . . . . . . . . 28
Hardware Provided . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . 3
Accessories . . . . . . . . . . . . . . . . . . . . . . . 7 . . . . . . . . . . . . 29
Completed Installation . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . 4
Replacement Parts . . . . . . . . . . . . . . . . . . 7 . . . . . . . . . . 30-31
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . 5-11
Having a Problem? . . . . . . . . . . . . . . . . . 8
Installation . . . . . . . . . . . . . . . . . . . . . . . 3-4 . . . . . . . . . . . . 12-21
Care of your Opener . . . . . . . . . . . . . . . . 9
Maintenance of your Operator . . . . . . . . 9
Operation of your Opener . . . . . . . . . . . . 9
Specifications . . . . . . . . . . . . . . . . . . . . . 10
Before You Begin
1. Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural supports.
2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not supplied) may be required.
3. Depending on your door's construction, you might need a special door arm. See your dealer.
4. Do you have an access door in addition to the garage door? If not, Model 1702E Outside Quick Release Accessory is required.
1
A.
B.
C.
D.
E.
One-Piece Door with Horizontal Track Only
One-Piece Door with Horizontal and Vertical Track – Special door
arm (E, The Chamberlain Arm™) required. See your dealer.
Sectional Door with Curved Track – See 20B – connect door
arm. The Protector System (29 (9) is required for doors that are
3m in height.
Canopy door – Special door arm (E, The Chamberlain Arm™)
and The Protector System (29 (9)) are required. See your dealer
The Chamberlain Arm™
Sleeve
Slide pulley bracket (1) and inner trolley (2) into back (opener end) of
rail assembly (3), be sure to insert pulley bracket as shown with arrow
(4) pointing toward front (header end) of rail (5). Push bracket toward
front (header end) of rail (5). Insert carriage bolt (6) through header
sleeve bracket (7). Loosely thread spring nut (8) onto carriage bolt.
Insert carriage bolt (6) of header sleeve assembly (7) into bold cut out
in pulley bracket (1). Slide header sleeve assembly (7) on to front
(header end) of rail (4).
2 Tools Required
8 Attach Trolley to Rail
3 Hardware Provided
(1) Clevis Pin
(2) Wood Screws
(3) Screws
(4) Clevis Pins
(5) Hex Screws
(6) Rope
(7) Handle
(8) Insulated Staples
(9) Anchors
(10) Lock Washer
(11) Nuts
(12) Ring Fastener
(13) 8mm Anchors
(14) Sheet Metal Screws
(15) Carriage Bolts
(16) Stop Bolt
4 Completed Installation
As you proceed with the assembly, installation and adjustment
procedures in this manual, you may find it helpful to refer back to
this illustration of a completed installation.
(1) Header Sleeve
(2) Chain Pulley Bracket
(3) Trolley
(4) Rail
(5) Chain
(6) Hanging Bracket
(7) Power Cord
(8) Opener
(9) Light Lens
(10) Manual Release
Rope & Handle
(11) Curved Door Arm
(12) Straight Door Arm
(13) Door Bracket & Plate
(14) Header Bracket
(15) Trolley Release Arm
ASSEMBLY SECTION
IMPORTANT: If you have a canopy or dual track one-piece door,
you need to use the instructions packed with The Chamberlain
Arm™ Accessory in conjunction with this Owner's Manual when
assembling the rail.
5 Assemble the Rail
Slide outer trolley (1) into rail assembly (2), be sure arrow on trolley
(3) is heading in direction of door is heading in direction of door (4).
Slide outer trolley down rail until it engages with inner trolley.
9 Attach Chain Spreader
Attach chain spreader (1) to opener (2) with phillips pan head
screws (3).
10 Fasten Rail to Opener & Install Chain
Remove four washered bolts (1) from top of opener. Place rail (2) on
opener, flush with stops (3) on top of opener. Wrap chain (4) around
slot in spreader (5) and over sprocket (6). Push idler pulley bracket
assembly toward front of the rail to eliminate excess slack in chain.
Align bolt holes on brackets (7) with bolt holes on opener. Secure
brackets to opener with previously removed bolts. Tighten bolts
securely. The opener sprocket teeth must engage the chain.
Insert bolt (8) into trolley stop bolt hole (9) secure with lock washer
(10) and nut (11).
CAUTION: Use only those bolts mounted in the top of opener.
Use of any other bolts will cause serious damage to opener.
11 Assemble Header Sleeve
Thread spring nut on carriage bolt unit finger tight. Insert a
screwdriver tip (1) into one of the slots of the nut ring (2) and brace it
firmly against the header sleeve. Place an open end wrench (3) on
the square end of the spring nut (4), slightly rotate nut about 1/4 turn
clockwise until nut ring (2) is released against header sleeve (5). This
sets spring to optimum chain tension. chain may slip off sprocket if
chain is too loose. If chain does slip re-tighten spring nut by turing nut
clockwise 1/2 turn. Do NOT overtighten chain.
NOTE: If your opener came with a one piece rail, proceed to step 8.
Grease inside edges of rail sections using grease (1). Place rail
pieces (2) on flat surface for assembly. All four rail sections are
interchangeable. Slide rail braces (3) onto rail section. Connect rail by
sliding rail brace onto next rail section. Tap rail assembly (4) on piece
of wood (5) until rail sections are flush. Repeat with remaining rail
sections.
6 Install the Chain
Remove chain from carton and lay chain out on floor (do not allow
chain to twist). Push pins of master link bar (3) through chain link (4)
and hole in trolley (5) (see picture). Push cap (2) over pins and onto
notches. Slide clip-on spring (1) over cap and onto pin notches until
both pins are securely locked in place.
2
2-en
7 Insert Chain into Rail & Assemble Header
1 Door Types
15 Position the Opener
Wear protective goggles when working overhead to protect your
eyes from injury.
NOTE: A 25mm (1") board (1) is convenient for setting an ideal doorto-rail distance (unless headroom is not sufficient).
Raise the opener onto a stepladder. Open garage door. Place a
25mm (1") board (1) laid flat on the top section of door near the
centerline as shown. Rest the rail on the board.
If the raised door hits the trolley, pull down on the trolley release arm
to disconnect the inner and outer trolley sections. The trolley can
remain disconnected until connecting door arm to trolley is
completed.
Disengage all existing garage door locks to avoid damage to the
garage door.
To avoid serious personal injury from entanglement, remove all
ropes connected to the garage door before installing the opener.
It is recommended that the opener be installed 2,1m (7 feet) or more
above the floor where space permits.
12 Position the Header Bracket
The header bracket must be rigidly fastened to a structural
support of the garage. Reinforce the wall or ceiling with a 40mm
(1-1/2") board if necessary. Failure to comply may result in
improper operation of safety reverse system.
You can attach the header bracket either to the header wall (1) or to
the ceiling (3). Follow the instructions which will work best for your
particular requirements.
With the door closed, mark the vertical centerline (2) of the garage
door. Extend line onto header wall above the door.
Open door to highest point of travel. Draw an intersecting horizontal
line (4) on header wall 5cm (2") above high point to provide travel
clearance for top edge of door.
13 Install the Header Bracket
NOTE: Refer to vertical center and horizontal lines created in
step 12 for proper placement or header bracket.
A. Wall Mount: Center the bracket (1) on the vertical guideline (2)
with the bottom edge of the bracket on the horizontal line (4)
(with the arrow pointing toward the ceiling). Mark all of the bracket
holes (5). Drill 4,5mm (3/16") pilot holes and fasten the bracket
with wood screws (3). For concrete mount, use concrete anchors
provided.
B. Ceiling Mount: Extend vertical guideline (2) onto the ceiling.
Center the bracket (1) on the vertical mark no more than 150mm
(6") from the wall. Make sure the arrow is pointing toward the wall.
Mark all of the bracket holes (5). Drill 4,5mm (3/16") pilot holes and
fasten the bracket with wood screws (3). For concrete ceiling
mount, use concrete anchors (6) provided.
14 Attach Rail to Header Bracket
Position opener on garage floor below the header bracket. Use
packing material to protect the cover. Raise rail until holes in the
header sleeve and holes in the header bracket align. Join with clevis
pin (1). Insert ring fastener (2) to secure.
NOTE: To enable the rail to clear sectional door springs, it may be
necessary to lift opener onto a temporary support. The opener must
either be secured to a support or held firmly in place by another
person.
16 Hang the Opener
The opener must be securely fastened to a structural support of
the garage.
Three representative installations are shown. Yours may be different.
Hanging brackets (1) should be angled (Figure A) to provide rigid
support. On finished ceilings, (Figure B) attach a sturdy metal bracket
(not supplied) (4) to a structural support before installing the opener.
For concrete ceiling mount, (Figure C), use concrete anchors (5)
provided.
On each side of opener measure the distance from the opener to the
structural support (or ceiling).
Cut both pieces of the hanging bracket to required lengths. Flatten
one end of each bracket and bend or twist to fit the fastening angles.
Do not bend at the bracket holes. Drill 4,5mm (3/16") pilot holes in
the structural supports (or ceiling). Attach flattened ends of brackets
to supports with wood screws (2).
Lift opener and fasten to hanging brackets with screw, lock washer
and nut (3). Check to make sure rail is centered over the door.
Remove 25mm (1") board. Operate door manually. If door hits the
rail, raise header bracket. Use rail grease and lubricate bottom
surface of rail (6).
17 Attach Emergency Release Rope &
Handle
Thread one end of rope (1) through hole in top of red handle so
"NOTICE" reads right side up as shown (3). Secure with an overhand
knot (2). Knot should be at least 25mm (1") from end of the rope to
prevent slipping.
Thread other end of rope through hole in release arm of the outer
trolley (4). Adjust rope length so that handle is 1,8m (6 feet) above
the floor. Secure with an overhand knot.
NOTE: If it is necessary to cut rope, heat seal cut end with a match or
lighter to prevent fraying.
3
3-en
INSTALLATION SECTION
20 Fasten Door Bracket
Press the release tabs on both sides of lens (2). Gently rotate lens
back and downward until the lens hinge is in the fully open position.
Do not remove the lens. Install a 40 watt (socket size E27), maximum
light bulb (1) in the socket (3) as shown. The light will turn on and
remain lit for 2-1/2 minutes when power is connected. After 2-1/2
minutes it will turn off. Reverse the procedure to close the lens.
Replace burned out bulbs with rough service light bulbs.
If yours is a canopy or dual-track one-piece style garage door, a door
arm conversion kit is required. Follow the installation instructions
included with the replacement door arm. Exercise care in removing and
assembling arm conversion kit. Keep fingers away from the sliding
parts.
Connect Electric Power
Sectional and One-Piece Door Installation Procedure:
TO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN THE
GARAGE DOOR OPENER UNTIL INSTRUCTED TO DO SO.
Door bracket (1) has left and right side fastening holes. Assemble
and install the bracket and plate (2) if your installation requires top
and bottom fastening holes.
Connect the opener to a mains which is properly EARTHED
according to the wiring instruction tag attached to power supply
cord (and as specified by local code).
NOTE: Horizontal and vertical reinforcement is needed for lightweight
garage doors.
19 Install Lighted Door Control Button
1. Center bracket (with or without plate, as required) at the top of
inside face of door as shown. Mark holes.
A.Standard Sectional or One-piece doors: locate bracket at
inside face of the door.
B. Sectional doors with two horizontal roller channels: 150 250mm below the top of the door.
Locate push buttons where the garage door is visible (at a
height of at least of 1,5m), away from door and door hardware
and out of the reach of children.
2. A. Wooden doors
Drill 8mm holes (5/16") and fasten the door bracket with nut,
lock washer, and carriage bolt (3) or use wood screws.
Serious personal injury from a moving garage door may result
from misuse of opener. Do not allow children to operate the
lighted door control button or remote control transmitter.
Permanently fasten the caution label on the wall near the lighted
door control button as a reminder of safe operating procedures.
There are 2 screw terminals (1) on the back of the lighted door
control button (2). Strip about 6mm (1/4") of insulation from bell wire
(4). Separate wires enough to connect the white/red wire to terminal
screw 1 and the white wire to terminal screw 2.
Fasten the lighted door control button to an inside garage wall with
sheet metal screws (3) provided. Drill 4mm (5/32") holes and use
anchors (6) if installing into drywall. A convenient place is beside the
service door and out of reach of children.
Run the bell wire up the wall and across the ceiling to the garage
door opener. Use insulated staples (5) to secure wire. The receiver
quick connect terminals are located on the back panel of the opener.
Connect the bell wire to the terminals as follows: white/red to red (7)
and white to white (8).
Operation of the Lighted Door Control Button
Press to open or close the door. Press again to reverse the door
during the closing or opening cycle.
B. Sheet metal doors
Fasten with sheet metal screws (4).
C. One-piece door optional
Fasten with sheet metal screws (4).
21 Assemble Door Arm and Set Limits
NOTE: For one-piece doors, do not connect door arm to trolley
before adjusting limits. Failure to follow instructions may result in
damage to door. See below.
A. ONE-PIECE DOOR INSTALLATION:
Connect straight door arm (1) and curved door arm sections (2) to
obtain the longest possible length with hardware (3, 4 & 5). With door
closed, connect straight door arm section to door bracket with a
clevis pin (6). Secure with a ring fastener (7).
Before connecting door arm to trolley, adjust travel limits. Limit
adjustment screws are located on left side panel.
Open Door Adjustment: Decrease up limit. Turn up limit adjustment
screw counterclockwise 4-1/2 turns.
Press door control button. Trolley will travel to full open position (8).
Manually raise door to open position (parallel to floor) and lift door
arm (9) to trolley. The arm should touch trolley just in back of door
arm connector hole (10) as shown in solid line drawing. Increase up
limit if necessary. One full turn equals 7,5cm (3") of door travel.
Closed Door Adjustment: Decrease down limit. Turn down limit
adjustment screw clockwise 4 complete turns.
Press door control button. Trolley will travel to full closed position
(11). Manually close door and lift door arm (12) to trolley. The arm
should touch trolley just ahead of door arm connector hole (10) as
shown in dotted line drawing. Decrease down limit if necessary. One
full turn equals 7,5cm (3") of door travel.
Connect Door Arm to Trolley: With door closed, connect curved arm
to trolley with remaining clevis pin. Secure with ring fastener. NOTE:
Lift door slightly to make connection if necessary.
Run opener through a complete travel cycle. If door has a slight
"backward" slant in full open position, decrease up limits until door
is parallel to floor.
B. SECTIONAL DOOR INSTALLATION:
Connect according to Figure B, then proceed to Step 24.
4
4-en
18 Install Light
23 Program your Keyless Entry (optional)
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or leave
garage while door is in motion. Do not allow children to operate
push button(s) or remote(s). Do not allow children to play near
the door.
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or leave
garage while door is in motion. Do not allow children to operate
push button(s) or remote(s). Do not allow children to play near
the door.
Your garage door opener receiver and remote control transmitter are
set to a matching code. If you purchase additional remote controls,
the garage door opener must be programmed to accept the new
remote code.
Program the Receiver to Match Additional Remote Control
Codes:
NOTE: Your new Keyless Entry must be programmed to operate your
garage door opener.
Program the Receiver to Match Additional Remote Control Code
Using the orange “LEARN” Button:
Using the “LEARN” Button
2. Within 30 seconds, enter a four digit personal identification number
(PIN) of your choice on the keypad (2), then press and hold the
ENTER button.
1. Press and release the “learn” button on the motor unit. The learn
indicator light will glow steadily for 30 seconds (1).
2. Within 30 seconds, press and hold the button on the hand-held
remote that you wish to operate your garage door (2).
3. Release the button when the motor unit light blinks. It has learned
the code. If light bulb is not installed, two clicks will be heard (3).
Using the Multi-Function Door Control (optional):
1. Press and hold the button on the hand-held remote that you wish
to operate your garage door (4).
2. While holding the remote button, press and hold the LIGHT button
on the Multi-Function Door Control (5).
3. Continue holding both buttons while you press the push bar on the
Multi-Function Door Control (all three buttons are held) (6).
4. Release buttons when the motor unit light blinks. It has learned the
code. If light bulb is not installed, two clicks will be heard (7).
Now the opener will operate when the remote control push button is
pressed. If you release the remote control push button before the
opener lights flash, the opener has not learned the code.
To Erase all Remote Control Codes
1. Press and release the orange “learn” button (1) on opener. The
learn indicator light will glow steadily for 30 seconds.
3. Release the button when the opener light blinks (3). It has learned
the code. If light bulb is not installed, two clicks will be heard.
NOTE: This method requires two people if the Keyless Entry is
already mounted outside the garage.
Using the Multi-Function Door Control (optional):
1. Enter a four digit personal identification number (PIN) of your
choice on the keypad, then press and hold ENTER (4).
2. While holding the ENTER button, press and hold the LIGHT button
on the Multi-Function Door Control (5).
3. Continue holding the ENTER and LIGHT buttons while you press
the push bar on the Multi-Function Door Control (all three buttons
are held) (6).
4. Release buttons when the opener light blinks. It has learned the
code. If light bulb is not installed, two clicks will be heard (7).
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor unit until the learn
indicator light goes out (approximately 6 seconds). All previous codes
are now erased. Reprogram each remote or keyless entry you wish to
use.
3-Channel Remote:
If provided with your garage door opener, the large button is factory
programmed to operate it. Additional buttons on any rolling code
3-channel remote or mini-remote can be programmed to operate
other rolling code garage door openers or gates.
5
5-en
22 Program your Opener & Remote
25 Force Settings
Run the opener through a complete travel cycle. Limit adjustments
are not necessary when the door opens and closes completely and
doesn't reverse unintentionally in the fully closed position.
Locate the orange button (1) on the back panel of motor unit. Push
the orange button twice to enter into Force Setting Mode.
NOTE: Repeated operation of the opener during adjustment
procedures may cause motor to overheat and shut off. Allow a 15
minute cooling period after 5 continuous operations of the opener.
Read the following carefully before proceeding to Force Adjustment.
Use a screwdriver to make limit adjustments.
If Door Doesn't Open Completely but Opens at Least 1,5m (5
feet): Increase up travel. Turn the up limit adjustment screw (3)
clockwise. One turn equals 5cm (2") of travel.
If door does not open at least 1,5m (5 feet). Adjust force, see
Force Adjustment: Place the opener into the Force Adjustment
Mode, see Force Adjustment.
If Door Doesn't Close Completely: If door arm is at maximum
length, increase down travel. Turn down limit adjustment screw (2)
counterclockwise. One turn equals 5cm (2") of travel. If the door still
will not close completely, the header bracket is positioned too high.
If Opener Reverses in Fully Closed Position: Decrease down
travel. Turn down limit adjustment screw (2) clockwise. One turn
equals 5cm (2") of travel.
If Door Reverses when Closing and there is no Interference to
Travel Cycle: Test door for binding. Pull manual release handle.
Manually open and close door. If door is binding, call a door
serviceman. If door is not binding or unbalanced, place the opener
into the Force Setting Mode, see Force Settings.
PROCEED TO STEP 25 “FORCE SETTINGS” TO COMPLETE
STEP 24 “LIMIT ADJUSTMENT”. Forces must be learned in order
for limit adjustments to operate properly.
The force, as measured on the closing edge of the door, should not
exceed 400N (40kg). If the closing force is measured to more than
400N, the Protector System must be installed See step 27.
The force setting button is located on the back panel of the motor
unit. The force setting regulates the amount of power required to
open and close the door. If the forces are set too light, door travel
may be interrupted by nuisance reversals in the down direction and
stops in the up direction.
Locate the orange button (1) on the back panel of motor unit. Push
the orange button twice to enter into Force Setting Mode. The LED
(Indicator Light) will flash. Push the wall control or the programmed
remote control that was shipped with your opener. The door will travel
to either the OPEN or CLOSE position. Push the button again, the
door will travel to the opposite position. Push the button again if the
LED is stilling blinking.
The door must travel through a complete cycle UP and DOWN in
order for the force to be set properly. If the unit stops before it
reaches the Open or Close Limit repeat the process. The LED
(indicator light) will stop flashing when the force has been learned.
To restore factory force settings, first enter force learn mode by
pressing the orange button twice. With the door open, press and hold
the wall control until door is fully closed.
26 Test the Safety Reverse System
The safety reverse system test is important. Garage door must
reverse on contact with a 40mm obstacle laid flat on the floor.
Failure to properly adjust opener may result in serious personal
injury from a closing garage door. Repeat test once a month and
adjust as needed.
Procedure: Place a 40mm obstacle (1) laid flat on the floor under the
garage door. Operate the door in the down direction. The door must
reverse on the obstruction. If the door stops on the obstruction, it is
not traveling far enough in the down direction. Increase the down
limit by turning down limit adjustment screw counterclockwise 1/4
turn. Repeat test.
When the door reverses on the 40mm obstacle, remove the
obstruction and run the opener through a complete travel cycle. Door
must not reverse in closed position. If it does, adjust Limits and
Force and repeat safety reverse test.
Place 20kg at the center of the door and ensure that the door will not
move up more than 500mm.
6
6-en
24 Limit Adjustment
29 Accessories
(See accessories)
The force, as measured on the closing edge of the door, should
not exceed 400 N (40kg). If the closing force is adjusted to more
than 400 N, the Protector System must be installed.
After opener has been installed and adjusted, The Protector
System™ accessory can be installed. Instructions are included with
this accessory.
The Protector System™ provides an additional measure of
safety against a small child being caught under a garage door.
It uses an invisible beam which, when broken by an obstruction,
causes a closing door to open and prevents an open door from
closing and is strongly recommended for homeowners with young
children.
(1) Model 94330E
(2) Model 94333E
(3) Model 94335E
(4) Model 94334E
(5) Model 975EML
(6) Model 128LM
(7) Model 9747E
(8) Model 78LM
(9) Model 760E
(10) Model 1702E
(11) Model 770E
(12) Model 1703E
(13) Model FLA230
(14) Model 16200LM
(15) Model MDL100LM
(16) Model EQL01
Model EQL02
(17) Model 100027
28 Special Features
A.
Door within a door connection
B.
Disconnect opener from power!
Remove cover. Locate auxiliary terminal block (TB1) on the
control board. Remove jumper from terminal leads 1 and 2 (not
shown). Replace with contact switch leads as shown.
Flashing light connection
C.
The flashing light can be installed anywhere. Connect light leads
to terminals 3 and 4 on the terminal block.
Coaxial antenna adapter
A coaxial antenna connection can be used if the transmitter
range is too short. Cut off the existing antenna. Use standard
coax cable and connector. Strip off end of insulation to “X”
dimension.
433 MHz: X = 250mm. Reposition antenna.
Model 100041
7-en
27 Install the Protector System™
Single-Function Remote Control
3-Function Remote Control
3-Function Mini Remote Control
4-Function Mini Remote Control
Laser Garage Parking Assist
2-Function Wireless Wall Control
Keyless Entry System
Multi-Function Door Control Panel
Outside Keylock
Outside Quick Release
The Protector System™
The Chamberlain Arm™
Flashing Light Kit
Pedestrian Door Switch
Mechanical Door Latch Kit
Door Handle Quick Release - 2.5m
Door Handle Quick Release - 4.0m
1-Position Key Switch (Flush Mount 100010)
2-Position Key Switch (Flush Mount 100034)
WIRING INSTRUCTIONS FOR ACCESSORIES
Keyless Entry System – To opener terminals: Red-1 and White-2
Outside Keylock – To opener terminals: Red-1 and White-2
Protector System™ – To opener terminals: White-2 and Black-3
Door Control Panel – To opener terminals: Red-1 and White-2
30 31 Replacement Parts
7
1. Opener doesn't operate from either door control or remote:
• Does the opener have electric power? Plug lamp into outlet. If it
doesn't light, check the fuse box or the circuit breaker. (Some
outlets are controlled by a wall switch.)
• Have you disengaged all door locks? Review installation instruction
warnings on page 1.
• Is there a build-up of ice or snow under door? The door may be
frozen to ground. Remove any obstruction.
• The garage door spring may be broken. Have it replaced.
• Repeated operation may have tripped the overload protector in the
motor. Wait 15 minutes. Try again.
2. Opener operates from remote but not from door control:
• Is door control button lit? If not, remove the bell wire from the
opener terminals. Short the red and white terminals by touching
both terminals at the same time with a piece of wire. If the opener
runs, check for a faulty wire connection at the door control, a short
under the staples, or a broken wire.
• Are wiring connections correct? Review page 4.
3. Door operates from door control but not from remote:
• Check battery. Replace battery if necessary.
• Is the light at the wall control flashing? Press button with key-symbol
to unlock the opener against remote controls.
• Is the receiver LED flashing at the back-side of the opener when the
transmitter is pressed? The opener receiver must re-learn the
remote control code. Follow the instructions on page 5.
• If you purchased a new remote control then check at carton of
remote control for compatibility or call the Service Hotline.
4. Remote has short range:
• Is battery installed? If needed, change the battery.
• Change the location of the remote control on the car.
• A metal garage door, foil-backed insulation or metal siding will
reduce the transmission range.
• Use outside coaxial antenna adapter to move antenna.
5. Door reverses for no apparent reason and opener light doesn't
blink:
• Is something obstructing the door? Pull manual release handle.
Operate door manually. If it is unbalanced or binding, call for
professional garage door service.
• Clear any ice or snow from garage floor area where garage
door closes.
• Review Force Settings. Open and close the door in learn mode for
several (3-5) consecutive cycles to allow the operator to adjust to
inconsistent doors.
• If door reverses in FULLY CLOSED position, re-learn travel limits.
Repeat safety reverse test after adjustment is complete.
The need for occasional adjustment of the force and limit settings is
normal. Weather conditions in particular can affect door travel.
6. Door reverses for no apparent reason and opener light blinks
for 5 seconds after reversing:
8-en
HAVING A PROBLEM?
• Delete all remote controls and reprogram.
• Make sure remote push button is not stuck "on".
• Disconnect all push buttons or key switches attached and wait one
day.
9. Door stops but doesn't close completely:
Review Limit Adjustment section.
Repeat safety reverse test after any adjustment of door arm length,
close force or down limit.
10. Door opens but won't close:
• Check The Protector System™ (if you have installed this
accessory). If the light is blinking, correct alignment.
• If opener light does not blink and it is a new installation, check the
down force.
Repeat the safety reverse test after the adjustment is complete.
11. Opener light does not turn on:
Replace light bulb (40 Watts maximum). Replace burned out bulbs
with rough service light bulbs.
12. Opener light does not turn off:
There may be a defective earth at the ceiling or wall receptacle.
The unit must be earthed.
13. Opener strains or stops during opening:
Door may be unbalanced or springs are broken. Close door and use
manual release rope and handle to disconnect trolley. Open and
close door manually. A properly balanced door will stay in any point
of travel while being supported entirely by its springs. If it does not,
call for professional garage door service to correct the problem. Do
not change force settings.
14. Opener motor hums briefly, then won't work:
• Garage door springs are broken. SEE ABOVE.
• If problem occurs on first operation of opener, door is locked.
Disable door lock. If chain was removed and reinstalled, the motor
may be out of phase. Remove chain; cycle motor to down position.
Observe drive sprocket. When it turns in clockwise direction and
stops in down position, re-install chain.
Repeat safety reverse test after adjustment is complete.
15. Opener won't activate due to power failure:
• Pull manual release rope and handle down to disconnect trolley.
Door can be opened and closed manually. When the power is
restored, pull the manual release handle straight back. The next
time the opener is activated, the trolley will reconnect.
• The Outside Quick Release accessory (if fitted) disconnects the
trolley from outside the garage in case of power failure.
Check The Protector System™ (if you have installed this accessory).
If the light is blinking, correct alignment.
7. Opener noise is disturbing in living quarters of home:
If operational noise is a problem because of proximity of the opener
to the living quarters, Vibration Isolator Kit 41A3263 can be installed.
This kit was designed to reduce the "sounding board effect" and is
easy to install.
8. The garage door opens and closes by itself:
8
OPERATION OF YOUR OPENER
When properly installed, opener will provide high performance with
a minimum of maintenance. The opener does not require additional
lubrication.
Limit Adjustments: These adjustments must be checked and
properly set when opener is installed. Only a screwdriver is
required. Weather conditions may cause some minor changes in the
door operation, requiring some re-adjustments, particularly during the
first year of operation.
Refer to the limit adjustments and force settings on page 5. Follow
the instructions carefully and repeat the safety reverse test after
any adjustment.
Remote Control Transmitter: The portable remote control may be
secured to a car sun visor with the clip provided. Additional remotes
can be purchased at any time for use in all vehicles using garage.
Refer to Accessories. Any new remotes must be set to the same
code as the original remote.
Remote Control Battery: The lithium batteries should produce
power for up to 5 years. If transmission range lessens, check the
battery.
To Change Battery: To replace batteries, use the visor clip or
screwdriver blade to pry open the case. Insert batteries positive side
up. To replace cover, snap shut along both sides. Do not dispose of
the old battery with household waste. Take batteries to a proper
disposal center.
Your opener can be activated by any of the following devices:
• The Lighted Door Control Button. Hold the button down until door
starts to move.
• The Outside Keylock or Keyless Entry System (if you have
installed either of these accessories).
• The Remote Control Transmitter. Hold the push button down until
the door starts to move.
Opening the Door Manually:
Door should be fully closed if possible. Weak or broken springs
could allow an open door to fall rapidly. Property damage or
serious personal injury could result.
The door can be opened manually by pulling the release handle down
and back (toward the opener). To reconnect the door, pull the release
handle straight down.
Do not use the manual release handle to pull the door opener
or closed.
When the Opener is Activated by Remote Control or Lighted
Door Control Button:
1. If open, the door will close. If closed, the door will open.
2. If closing, the door will stop.
3. If opening, the door will stop.
4. If the door has been stopped in a partially open or closed position,
it reverse direction.
5. If an obstruction is encountered while closing, the door will reverse.
6. If an obstruction is encountered while opening, the door will
reverse briefly.
7. The optional Protector System™ uses an invisible beam which,
when broken by an obstruction, causes a closing door to open
and prevents an open door from closing. It is STRONGLY
RECOMMENDED for homeowners with young children.
Allow a 15 minute cooling period after 5 continuous operations
of the opener.
The opener light will turn on: 1. when opener is initially plugged in;
2. when the power is interrupted; 3. when the opener is activated.
The light turns off automatically after 2-1/2 minutes. Bulb size is
40 Watts maximum.
MAINTENANCE OF YOUR OPENER
Once a Month:
• Repeat safety reverse test. Make any necessary adjustments.
• Manually operate door. If it is unbalanced or binding, call for
professional garage door service.
• Check to be sure door opens and closes fully. Adjust Limits and/or
Force settings if necessary.
Once a Year:
Oil door rollers, bearings and hinges. The opener does not require
additional lubrication. Do not grease the door tracks. Grease rail and
trolley once a year.
9
9-en
CARE OF YOUR OPENER
10-en
SPECIFICATIONS
Max. Pull Force...............800N
Rated Power ...................400 W
Motor
Type................................Permanent split capacitor
Speed .............................1500 rpm
Volts................................230-240 Volts AC-50Hz Only
Noise level ......................60dB
Drive Mechanism
Gears ..............................16:1 worm gear reduction
Drive ...............................Chain with two-piece trolley on
steel rail.
Length of Travel..............Adjustable to 2,3m (7-1/2 feet)
Travel Rate .....................96-135mm (3,8"-5,3") per second
Lamp...............................On when door starts, off 2-1/2 minutes
after stop.
Door Linkage ..................Adjustable door arm. Pull cord trolley
release.
Safety
Personal .........................Push button stop in UP and DOWN
direction. Automatic force reversal in UP
and DOWN direction.
Electronic ........................Automatic force adjustments.
Electrical .........................Motor overload protector and low voltage
push button wiring.
Limit Device ....................Circuit actuated by limit nut.
Limit Adjustment .............Screwdriver adjustment on side panel.
Start Circuit .....................Low voltage push button circuit.
Dimensions
Length (Overall) ..............3,1m (122-1/2")
Headroom Required .......30mm
Hanging Weight ..............14,5 kg (32 lb)
Receiver
Memory Registers ..........8
Keypad Code Memory ....1
SPECIAL NOTE: Chamberlain strongly recommends that the
protector system be installed on all garage door openers.
10
Chamberlain GmbH warrants to the first retail purchaser of this product (55802GB) that the product shall be free from any defect in materials and/or
workmanship for a period of 24 full months (2 years) from the date of purchase.
Upon receipt of the product, the first retail purchaser is under obligation to check
the product for any visible defects.
Conditions: The warranty is strictly limited to the reparation or replacement of
the parts of this product which are found to be defective and does not cover the
costs or risks of transportation of the defective parts or product.
This warranty does not cover non-defect damage caused by unreasonable use
(including use not in complete accordance with Chamberlain’s instructions for
installation, operation and care; failure to provide necessary maintenance and
adjustment; or any adaptations of or alterations to the products), labor charges
for dismantling or reinstalling of a repaired or replaced unit or replacement
batteries.
A product under warranty which is determined to be defective in materials
and/or workmanship will be repaired or replaced (at Chamberlain's option) at no
cost to the owner for the repair and/or replacement parts and/or product.
Defective parts will be repaired or replaced with new or factory rebuilt parts at
Chamberlain's option.
If, during the warranty period, the product appears as though it may be
defective, contact your original place of purchase.
This warranty does not affect the purchaser’s statutory rights under applicable
national legislation in force nor the purchaser’s rights against the retailer arising
from their sales/purchase contract. In the absence of applicable national or EU
legislation, this warranty will be the purchaser’s sole and exclusive remedy, and
neither Chamberlain nor its affiliates or distributors shall be liable for any
incidental or consequential damages for any express or implied warranty
relating to this product.
No representative or person is authorized to assume for Chamberlain any other
liability in connection with the sale of this product.
Declaration of Conformity
Automatic garage door openers, as stated, are in conformity to the applicable sections of EN55014-1
(2000), EN55014-2 (1997), EN61000-3-2 (2000), EN61000-3-3 (1995), EN 301 489-3 (V1.3.1),
EN 300 220-3 (V1.1.1), EN60335-1 (1994), and EN60335-2-95 (2004).
Per the provisions of the European Directives, 2004/108/EC, 2006/95/EC and 1999/5/EC, including all
amendments;
Model:........................................................................................................................................5580
Manufacturer
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126
USA
All technical file information for the operator and its accessories is held at The Chamberlain Group and
will be made available at the request of the authorities should the need arise.
Declaration of Incorporation
A power door operator must not be put into service until it has been completely and safely assembled
and installed, with appropriate size and weight of door, in accordance with both the door and operator
manufacturers’ instructions using suitable connection arms, appropriate safety devices, and the
complete installation has been declared in conformity with the provisions of EN12453, EN13241-1 and
the Machinery Directive, 89/392/EEC.
Door Types: Canopy, Fully Retracting or Sectional
Operator
Type
Maximum Area Installer: Indicate Maximum Weight (kg) Installer: Indicate
(m2)
Installed Door
Installed Door
Size
Weight
5580
13.5
110
Other Requirements: Operators used in the following installations must also be installed with the items
noted below.
Door Type
Accessory
Canopy
The Chamberlain Arm
Canopy
The Protector System
Sectional, 3m high
The Protector System
Installer: Indicate if “not applicable” or
if the item is installed
________________________________________
Installer Name/Signature
B. P. Kelkhoff
Manager, Regulatory Affairs
________________________________________
Company Name
Chamberlain GmbH.
D-66793 Saarqellingen
March, 2008
________________________________________
Address
_____________________________________
Date
114A2844F
© 2008, Chamberlain GmbH
All rights reserved
11-en
GARAGE DOOR OPENER WARRANTY
2 (4x)
5
3 (2x)
1 (2x)
6
5
7
de
Abbildungen
3780 / 5580
fr
Figures
3780 / 5580
4 (2x)
5 (4x)
7 (1x)
6 (1x)
en
Illustrations
3780 / 5580
da
Illustration
3780 / 5580
3
10 (7x)
9 (2x)
11 (7x)
NOTIC
E
4
1
5
2
14 (2x)
13 (4x)
12 (4x)
4
8
Ilustraciones
el
8
it
no
nl
pt
1
sv
3780 / 5580
Illustrazioni
3780 / 5580
Illustrasjon
3780 / 5580
Afbeeldingen
3780 / 5580
Figuras
3780 / 5580
Bild.
3780 / 5580
6
16 (1x)
19
18
17
A-1”
with rail
bei der Schiene
bij de rail
lors du rail
a la orilla del rail
hos skinnen
3
21
20
1
4
con la guida
sobre la calha
omkring skenan
kisko aidata
7
1
2
8
6
2
22
2
1
1
5
3780 / 5580
Kuvat
fi
3780 / 5580
™¯‹Ì·Ù·
3
7
4
15 (2x)
es
3
6
8
6
4
3
A- 1/2”
8
1
A
4
B
4
3
3
3
2
9
1
1
1
3
3
1
2
2
4
2
C
The Chamberlain D
Group, Inc.
Figure 2 - Tools
4210E - 3/8/93
E
B
10
1
4
3
2
5
5
6
7
1
3
3
6
5
8
6
2
14
11
9
4
9
15
10
12
13
11
8
10
11
2
10
3
2
8
10
11
1
11
2
4
2
1
12
5
1
4
10mm, 8mm,
4,5mm, 4mm
2
11mm, 13mm
3
13
3
2 (4x)
1 (2x)
2
3 (2x)
5
4
5
4 (2x)
5 (4x)
10 (7x)
9 (2x)
11 (7x)
5
8
NOTIC
E
13 (4x)
12 (4x)
3
50mm
(2")
7 (1x)
6 (1x)
5
1
4
2
14 (2x)
A
14
5
15 (2x)
19
18
17
21
22
1
2
with rail
bei der Schiene
bij de rail
lors du rail
a la orilla del rail
hos skinnen
con la guida
sobre la calha
omkring skenan
kisko aidata
(6")
3
5
1
3
1
6
15
1
1
150mm
5
2
2
5
16 (1x)
20
2
3
B
2
1
A
16
B
2
1
1
2
4
3
17
26
25
2
3
2
1
4
3
6
1
1
NOT
ICE
6
3
1
2
2
1
18
C
1
40W
E27
5
1
2
3
The Chamberlain Group, Inc.
Figure 16 - Manual Release
4210E - 3/8/93
2
2
3
A
1
(2x)
3
5
6
B
28
TB1
1
(2x)
3
C
4
TB1
19
1
A. 0-100mm
B. 150-250mm
A
2
1
3
WHT
-2
4
B
2
C 6mm
1
1
R ED
-1
4
3
8
7
2
2
27
20
1
4
3
3
4
4
1
A. 0-100mm
B. 150-250mm
5
2
A
3
X = 433 MHz = 250mm
1 2 3 4
B
3
C
1
1
4
1
2
2
3
6
29
4
94330E
94333E
1
2
975EML
94334E
94335E
3
128LM
1703E
4
12
5
21
A
7
1
4
B
5
760E
78LM
9747E
22
7
A
7
2
5
8
6
4
1
7
1
4
B
5
11
EQL01 -2,5m
EQL02 -4,0m
MDL100LM
16200LM
FLA230
10
9
8
LOCK
LIGHT
3
6
770E
9
19
1
7KG
7KG
53
53
6
11
1702E
100027/100010
100041/100034
10
10
3
1
6
2
3
2
12
11
6
7
3
12
5
4
5
6
7
2
3
LOCK
5
8
The Chamberlain Group, Inc.
Figure 17 10- Wall Control
4210E
3/6/92
6
9
4
7
16
13
6
4LIGHT
1
10
LOCK
14
LIGHT
15
17
3
2
6
9
6
7
30
3
5
4
31
41B4494-1
41B616
1
C
VD
12
41A5639-7
Pb
10A20
Cd
24
41A5817
12C810
83A11
171A28
7423CR3
41A5811
Hg
41A2828
41B4103-1
41A5833
175B174
NOT
ICE
012B0905
012B0906
12C855
23
1
1
(2x)
9
19
1
7KG
7KG
53
53
2
41B4375
178B34
41A5813
41A5801 (2.3m)
41A5801-1 (1.7m)
41A5801-2 (2.5m)
41A5803-3 (3.0m)
183D177
108D68-1
41A6420
183D178
178B69
30B415
41A5809
81C253
41C4398A
3
LOCK
41A5640
LIGHT
210C42
1
2
3
4
5
6
LOCK
7
1
(2x)
178B35
41A5525-27
LIGHT
LOCK
LIGHT
12C778
7023CR3
7025CR3
7030CR3
41A3475-24
41A5800
109A46 1”
4A1008 1/2”
114A3580-02.2008