Chamberlain 973G Garage Door Opener User Manual

Owner’s Manual
Installation and Operation
Models:
6000CMOD-IPI
8000CMOD-IPI
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC OT
AR
D
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
A. Congratulations
This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Congratulations on selecting a Heat & Glo gas fireplace, an
elegant and clean alternative to wood burning fireplaces.
The Heat & Glo gas fireplace you have selected is designed
to provide the utmost in safety, reliability, and efficiency.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
Your new Heat & Glo gas fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fireplace products!
We recommend that you record the following pertinent
information about your fireplace.
Homeowner Reference Information
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on fireplace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
The model information regarding your specific fireplace can be found on
the rating plate usually located in the control area of the fireplace.
Heat & Glo, a brand of Hearth & Home Technologies, Inc.
7571 215th Street West, Lakeville, MN 55044
Type of Gas
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz)
Gaz)::
NATURAL GAS
Gas and Electric
Information
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX · UL307B
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
Model Number
Serial Number
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 Listing and Code Approvals
A.
B.
C.
D.
E.
F.
G.
H.
7
7
7
7
7
7
7
8
2 Operating Instructions
Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote Controls, Wall Controls and Wall Switches . . . . . 10
IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . 11
Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . 11
Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 11
Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 12
After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 13
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . .
B. Maintenance Tasks-Qualified Service Technician . . . . . .
C. Glass Refractory, Base Pan, Burner and Valve
Assembly Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D. Burner Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
16
17
4 Getting Started
Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . .
Design and Installation Considerations . . . . . . . . . . . . . .
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . .
Inspect Appliance and Components . . . . . . . . . . . . . . . . .
18
19
19
19
5 Framing and Clearances
A.
B.
C.
D.
Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . .
Constructing the Appliance Chase . . . . . . . . . . . . . . . . . .
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
A.
B.
C.
D.
E.
Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
25
25
26
8 Vent Clearances and Framing
A.
B.
C.
D.
E.
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 32
Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . . 32
Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 33
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 34
Installing the Optional Heat-Zone® Gas Kit . . . . . . . . . . . . . 34
9 Appliance Preparation
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
B. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 36
C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 36
10 Installing Vent Pipe (DVP and SLP Pipe)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . .
Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . .
Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Install Decorative Ceiling Components (SLP only). . . . . .
Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . .
Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . .
Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . .
Install Decorative Wall Components (SLP only) . . . . . . . .
Heat Shield Requirements for Horizontal Termination . . .
Install Horizontal Termination Cap (DVP and SLP Pipe) .
37
38
38
39
39
40
41
41
42
42
42
43
11 Gas Information
Installer Guide
A.
B.
C.
D.
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 23
7 Vent Information and Diagrams
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
User Guide
A.
B.
C.
D.
E.
F.
G.
H.
 I.
J.
K.
L.
M.
6 Termination Locations
20
21
21
22
A.
B.
C.
D.
Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . .
44
44
44
44
12 Electrical Information
A.
B.
C.
D.
E.
F.
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IntelliFire PlusTM Ignition System Wiring . . . . . . . . . . . . . .
Optional Accessories Requirements . . . . . . . . . . . . . . . .
Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . .
Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Switch Installation for Fan (Optional) . . . . . . . . . . . .
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
45
45
45
46
46
46
3
13 Finishing
A.
B.
C.
D.
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Finish and Sealing Joints . . . . . . . . . . . . . . . . . . . . . . . . .
Door Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
48
48
49
14 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
I.
Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . .
Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glass Panel Installation . . . . . . . . . . . . . . . . . . . . . . . . . .
Media Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Trim and/or Surround . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
52
52
52
52
53
55
55
55
15 Troubleshooting
A. IntelliFire PlusTM Ignition System . . . . . . . . . . . . . . . . . . . 56
16 Reference Materials
A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 58
 B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 60
 C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
 = Contains updated information.
4
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
B. Limited Lifetime Warranty
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
Components Covered
Electric Venting
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
X
Firepots and burnpots
5 years
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 1 of 2
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
5
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
‡
‡
‡
‡
7KLVZDUUDQW\RQO\FRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGWKURXJKDQ++7DXWKRUL]HGGHDOHURUGLVWULEXWRU$OLVWRI
++7DXWKRUL]HGGHDOHUVLVDYDLODEOHRQWKH++7EUDQGHGZHEVLWHV
7KLVZDUUDQW\LVRQO\YDOLGZKLOHWKH++7DSSOLDQFHUHPDLQVDWWKHVLWHRIRULJLQDOLQVWDOODWLRQ
&RQWDFW\RXULQVWDOOLQJGHDOHUIRUZDUUDQW\VHUYLFH,IWKHLQVWDOOLQJGHDOHULVXQDEOHWRSURYLGHQHFHVVDU\SDUWVFRQWDFW
WKHQHDUHVW++7DXWKRUL]HGGHDOHURUVXSSOLHU$GGLWLRQDOVHUYLFHIHHVPD\DSSO\LI\RXDUHVHHNLQJZDUUDQW\VHUYLFH
IURPDGHDOHURWKHUWKDQWKHGHDOHUIURPZKRP\RXRULJLQDOO\SXUFKDVHGWKHSURGXFW
&KHFNZLWK\RXUGHDOHULQDGYDQFHIRUDQ\FRVWVWR\RXZKHQDUUDQJLQJDZDUUDQW\FDOO7UDYHODQGVKLSSLQJFKDUJHV
IRUSDUWVDUHQRWFRYHUHGE\WKLVZDUUDQW\
WARRANTY EXCLUSIONS:
7KLVZDUUDQW\GRHVQRWFRYHUWKHIROORZLQJ
‡ &KDQJHVLQVXUIDFHILQLVKHVDVDUHVXOWRIQRUPDOXVH$VDKHDWLQJDSSOLDQFHVRPHFKDQJHVLQFRORURILQWHULRUDQG
H[WHULRUVXUIDFHILQLVKHVPD\RFFXU7KLVLVQRWDIODZDQGLVQRWFRYHUHGXQGHUZDUUDQW\
‡ 'DPDJHWRSULQWHGSODWHGRUHQDPHOHGVXUIDFHVFDXVHGE\ILQJHUSULQWVDFFLGHQWVPLVXVHVFUDWFKHVPHOWHGLWHPV
RURWKHUH[WHUQDOVRXUFHVDQGUHVLGXHVOHIWRQWKHSODWHGVXUIDFHVIURPWKHXVHRIDEUDVLYHFOHDQHUVRUSROLVKHV
‡ 5HSDLURUUHSODFHPHQWRISDUWVWKDWDUHVXEMHFWWRQRUPDOZHDUDQGWHDUGXULQJWKHZDUUDQW\SHULRG7KHVHSDUWV
LQFOXGHSDLQWZRRGSHOOHWDQGFRDOJDVNHWVILUHEULFNVJUDWHVIODPHJXLGHVOLJKWEXOEVEDWWHULHVDQGWKHGLVFRORUDWLRQRIJODVV
‡ 0LQRUH[SDQVLRQFRQWUDFWLRQRUPRYHPHQWRIFHUWDLQSDUWVFDXVLQJQRLVH7KHVHFRQGLWLRQVDUHQRUPDODQGFRPSODLQWVUHODWHGWRWKLVQRLVHDUHQRWFRYHUHGE\WKLVZDUUDQW\
‡ 'DPDJHVUHVXOWLQJIURPIDLOXUHWRLQVWDOORSHUDWHRUPDLQWDLQWKHDSSOLDQFHLQDFFRUGDQFHZLWKWKHLQVWDOODWLRQ
LQVWUXFWLRQVRSHUDWLQJLQVWUXFWLRQVDQGOLVWLQJDJHQWLGHQWLILFDWLRQODEHOIXUQLVKHGZLWKWKHDSSOLDQFHIDLOXUHWR
LQVWDOOWKHDSSOLDQFHLQDFFRUGDQFHZLWKORFDOEXLOGLQJFRGHVVKLSSLQJRULPSURSHUKDQGOLQJLPSURSHURSHUDWLRQDEXVHPLVXVHFRQWLQXHGRSHUDWLRQZLWKGDPDJHGFRUURGHGRUIDLOHGFRPSRQHQWVDFFLGHQWRULPSURSHUO\
LQFRUUHFWO\SHUIRUPHGUHSDLUVHQYLURQPHQWDOFRQGLWLRQVLQDGHTXDWHYHQWLODWLRQQHJDWLYHSUHVVXUHRUGUDIWLQJ
FDXVHGE\WLJKWO\VHDOHGFRQVWUXFWLRQVLQVXIILFLHQWPDNHXSDLUVXSSO\RUKDQGOLQJGHYLFHVVXFKDVH[KDXVWIDQVRU
IRUFHGDLUIXUQDFHVRURWKHUVXFKFDXVHVXVHRIIXHOVRWKHUWKDQWKRVHVSHFLILHGLQWKHRSHUDWLQJLQVWUXFWLRQV
LQVWDOODWLRQRUXVHRIFRPSRQHQWVQRWVXSSOLHGZLWKWKHDSSOLDQFHRUDQ\RWKHUFRPSRQHQWVQRWH[SUHVVO\DXWKRUL]HG
DQGDSSURYHGE\++7PRGLILFDWLRQRIWKHDSSOLDQFHQRWH[SUHVVO\DXWKRUL]HGDQGDSSURYHGE\++7LQZULWLQJ
DQGRULQWHUUXSWLRQVRUIOXFWXDWLRQVRIHOHFWULFDOSRZHUVXSSO\WRWKHDSSOLDQFH
‡ 1RQ++7YHQWLQJFRPSRQHQWVKHDUWKFRPSRQHQWVRURWKHUDFFHVVRULHVXVHGLQFRQMXQFWLRQZLWKWKHDSSOLDQFH
‡ $Q\SDUWRIDSUHH[LVWLQJILUHSODFHV\VWHPLQZKLFKDQLQVHUWRUDGHFRUDWLYHJDVDSSOLDQFHLVLQVWDOOHG
‡ ++7¶VREOLJDWLRQXQGHUWKLVZDUUDQW\GRHVQRWH[WHQGWRWKHDSSOLDQFH¶VFDSDELOLW\WRKHDWWKHGHVLUHGVSDFH,QIRUPDWLRQLVSURYLGHGWRDVVLVWWKHFRQVXPHUDQGWKHGHDOHULQVHOHFWLQJWKHSURSHUDSSOLDQFHIRUWKHDSSOLFDWLRQ&RQVLGHUDWLRQPXVWEHJLYHQWRDSSOLDQFHORFDWLRQDQGFRQILJXUDWLRQHQYLURQPHQWDOFRQGLWLRQVLQVXODWLRQDQGDLUWLJKWQHVVRI
WKHVWUXFWXUH
This warranty is void if:
‡
‡
‡
7KHDSSOLDQFHKDVEHHQRYHUILUHGRURSHUDWHGLQDWPRVSKHUHVFRQWDPLQDWHGE\FKORULQHIOXRULQHRURWKHUGDPDJLQJ
FKHPLFDOV2YHUILULQJFDQEHLGHQWLILHGE\EXWQRWOLPLWHGWRZDUSHGSODWHVRUWXEHVUXVWFRORUHGFDVWLURQEXEEOLQJ
FUDFNLQJDQGGLVFRORUDWLRQRIVWHHORUHQDPHOILQLVKHV
7KHDSSOLDQFHLVVXEMHFWHGWRSURORQJHGSHULRGVRIGDPSQHVVRUFRQGHQVDWLRQ
7KHUHLVDQ\GDPDJHWRWKHDSSOLDQFHRURWKHUFRPSRQHQWVGXHWRZDWHURUZHDWKHUGDPDJHZKLFKLVWKHUHVXOWRIEXW
QRWOLPLWHGWRLPSURSHUFKLPQH\RUYHQWLQJLQVWDOODWLRQ
LIMITATIONS OF LIABILITY:
‡
7KHRZQHU¶VH[FOXVLYHUHPHG\DQG++7¶VVROHREOLJDWLRQXQGHUWKLVZDUUDQW\XQGHUDQ\RWKHUZDUUDQW\H[SUHVVRU
LPSOLHGRULQFRQWUDFWWRUWRURWKHUZLVHVKDOOEHOLPLWHGWRUHSODFHPHQWUHSDLURUUHIXQGDVVSHFLILHGDERYH,QQR
HYHQWZLOO++7EHOLDEOHIRUDQ\LQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVFDXVHGE\GHIHFWVLQWKHDSSOLDQFH6RPHVWDWHV
GRQRWDOORZH[FOXVLRQVRUOLPLWDWLRQRILQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVVRWKHVHOLPLWDWLRQVPD\QRWDSSO\WR\RX
7KLVZDUUDQW\JLYHV\RXVSHFLILFULJKWV\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\IURPVWDWHWRVWDWH(;&(3772
7+((;7(173529,'('%</$:++70$.(612(;35(66:$55$17,(627+(57+$17+(:$55$17<
63(&,),('+(5(,17+('85$7,212)$1<,03/,(':$55$17<,6/,0,7('72'85$7,212)7+(
(;35(66(':$55$17<63(&,),('$%29(
4021-645C 12-29-10
6
Page 2 of 2
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
1
Listing and Code Approvals
A. Appliance Certification
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
US
(0-2000 FT)
28,000
19,000
40
CANADA
(2000-4500 FT)
25,200
17,100
41
US
(0-2000 FT)
20,000
14,000
55
CANADA
(2000-4500 FT)
18,000
12,000
56
US
(0-2000 FT)
32,000
22,000
35
CANADA
(2000-4500 FT)
28,800
19,800
36
US
(0-2000 FT)
22,000
15,000
54
CANADA
(2000-4500 FT)
20,000
14,000
55
Models
MODELS: 6000CMOD-IPI, 8000CMOD-IPI
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.50b-2009 • CSA 2.22b-2009
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Tempered Glass Specifications
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the
Consumer Product Safety Commission (CPSC). The
tempered glass has been tested and certified to the requirements of ANSI Z97.1 and CPSC 16 CFR 1202
(Safety Glazing Certification Council SGCC# 1595 and
1597. Architectural Testing, Inc. Reports 02-31919.01 and
02-31917.01).
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
(U.S. or Canada)
6000CMOD-IPI
(NG)
6000CMOD-IPI
(LP)
8000CMOD-IPI
(NG)
8000CMOD-IPI
(LP)
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Check with your local gas utility to determine proper
orifice size.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
7
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
8
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
2
Operating Instructions
User Guide
• Install a switch lock or a wall/remote control with child
protection lockout feature.
A. Gas Fireplace Safety
WARNING
• Keep remote controls out of reach of children.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
• Teach children to NEVER touch the fireplace.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• Consider not using the fireplace when children will be
present.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fireplace for an extended period of time (summer months,
vacations, trips, etc):
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Remove batteries from remote controls.
• Turn off wall controls.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
• Unplug 6 volt transformer plug and remove batteries on
IPI models.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
WARNING! Choking Hazard! Keep media out of reach
of children.
B. Your Fireplace
WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
If you expect that small children or vulnerable adults may
come into contact with this fireplace, the following precautions are recommended:
• Install a physical barrier such as:
- A decorative firescreen.
- Adjustable safety gate.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.E.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 14.G.
MANTEL
SECTION 5.D
FAN KIT
SECTION 2.C.
HEARTH
CLEAR SPACE
SECTION 2.D.
Figure 2.1 General Operating Parts
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
9
C. Fan Kit (optional)
F. Fixed Glass Assembly
If desired, a fan kit may be added. Contact your dealer to
order the correct fan kit.
See Section 14.G.
D. Clear Space
G. Remote Controls, Wall Controls and Wall
Switches
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
Follow the instructions supplied with the control installed
to operate your fireplace.
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
For specific information on fireplace controls, see Section 12.
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
3F
T.
IN CLE
FR AR
ON S
T O PAC
FF E
IR
EP
LA
CE
Figure 2.2 Clear Space
E. Decorative Doors and Fronts
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
10
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
•
Locate the module selector switch. (See Figure 2.3).
The IntelliFire Plus system has a battery backup option.
Battery longevity and performance will be affected by the
service temperatures of this appliance.
•
Set the module selector switch to the OFF position.
•
Wait five (5) minutes to allow possible accumulated gas
to clear.
NOTICE: Batteries should only be used as a power source
in the event of an emergency such as an outage.
•
Set the module selector switch to ON or REMOTE
position.
I. Control Module Operation
•
Start the appliance.
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 2.3.
WARNING! Risk of Explosion! DO NOT reset the module more than one time within a five minute time period.
Gas may accumulate in firebox. Call a qualified service
technician.
H. IPI Battery Tray/Battery Installation
TM
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
remote. The unit should be in the OFF position during
installation, service, battery installation, fuel conversion,
and in the event that the control goes into LOCK-OUT
mode as a result of an error code.
MODULE
ON Position: Appliance will ignite and run continuously
in the HI flame setting, with no adjustment in flame
output. This mode of operation is primarily used for
initial installation or power outage operation with battery
backup.
SELECTOR
SWITCH
REMOTE Position: Appliance will initiate commands
from an optional wired wall switch and/or the wireless
remote (RC300).
2. If using a wired wall switch with the module in REMOTE
mode, the flame output can be adjusted with the HI/LO
selector switch on the module. See Figure 2.3. Note
that the flame HI/LO selector switch will become inactive
once an optional remote control (RC200/RC300) is
programmed to the control module. Note that the control
module will always ignite the fireplace on HI and remain
so for the initial 10 seconds of operation. If the HI/LO
is switched to the LO position, the flame output will
automatically drop to the lowest setting after the flame
has been established for 10 sec. After this 10 second
period, the flame can be adjusted from HI to LO with
the switch.
WIRE LEAD FROM
REGULATOR CONNECTS HERE
LP/NG GAS-TYPE
SELECTOR SWITCH

Figure 2.3 Control Module
Nine Hour Safety Shutdown Feature
This appliance has a safety feature that automatically
shuts down the fireplace after 9 hours of continuous
operation without receiving a command from the
RC300 remote.
3. The control module has safety feature that automatically
shuts down the fireplace after 9 hours of continuous
operation without receiving a command from the RC300
remote.
4. If you intend to use both an optional wired wall switch
and the RC300 remote control to operate your fireplace,
the wall switch will override any commands given by
the remote.
This module may lock-out under certain conditions.
When this occurs, the appliance will not ignite or
respond to commands. The module will go into lock-out
mode by emitting three audible beeps, then continuously
displaying an error code at its status indicator LED.
•
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
5. Module Reset

J. Before Lighting Fireplace
Check battery tray. Remove batteries if installed.
Batteries should only be installed for use during power
outages. See Section H.
• Review proper placement of glass panels and media.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
11
K. Lighting Instructions (IPI)
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS (IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burner. DO NOT try to light the burner by
hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• If you cannot reach your gas supplier, call the fire department.
Equipped with wall switch: Turn ON/OFF switch
to ON.
WARNING:
CAUTION:
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240
VAC) TO THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could
expose you to substances in fuel or
fuel combustion which are known to the
State of California to cause cancer, birth
defects, or other reproductive harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
2. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this label. If you do not smell gas, go to next step.
3. To light the burner:
• DO NOT touch any electric switch; do
not use any phone in your building.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
GAS
VALVE
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
Equipped with remote or wall control: Press
ON or FLAME button.
Equipped with thermostat: Set temperature to
desired setting.
4. If the appliance does not light after three tries,
call your service technician or gas supplier.
TO TURN OFF
GAS TO APPLIANCE
1. Equipped with wall switch: Turn ON/OFF switch
to OFF.
Equipped with remote or wall control: Press
OFF button.
Equipped with thermostat: Set temperature to
lowest setting.
2. Service technician should turn off electric
power to the control when performing service.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
12
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
593-913G
L. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.G.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fireplace.
NOTICE! Open windows for air circulation during fireplace break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
M. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the appliance.
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Film on the glass
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn
continually?
In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is
turned off. Some optional control systems available with IPI models may allow pilot flame to
remain lit. In a standing pilot system the pilot will always stay on.
Glass rock media color change
It is normal for the glass rock media to change color slightly over the lifetime of the
appliance.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
13
3
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Remote Control
Frequency: Seasonally
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend annual service by a qualified service technician.
By: Homeowner
A. Maintenance Tasks-Homeowner
• Locate remote control transmitter and receiver.
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service appointment.
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
Tools needed: Replacement batteries and remote control instructions.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
• Place batteries as needed in remote transmitters and
battery-powered receivers.
• Place remote control out of reach of children.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unintended operation:
• Remove batteries from remote controls.
• Unplug 6 volt transformer plug on IPI models.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
• Unplug battery backup from control module.
Glass Cleaning
Venting
Frequency: Seasonally
Frequency: Seasonally
By: Homeowner
By: Homeowner
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
Tools needed: Protective gloves and safety glasses.
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See
Section 6.
• Inspect for corrosion or separation.
• Verify weather stripping, sealing and flashing remains
intact.
• Inspect draft shield to verify it is not damaged or missing.
B. Maintenance Tasks-Qualified Service
Technician
Doors, Surrounds, Fronts
The following tasks must be performed by a qualified service technician.
Frequency: Annually
Gasket Seal and Glass Assembly Inspection
By: Homeowner
Frequency: Annually
Tools needed: Protective gloves, stable work surface
By: Qualified Service Technician
• Assess condition of screen and replace as necessary.
• Inspect for scratches, dents or other damage and repair
as necessary.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
14
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
Interior Ceramic Glass Panel Cleaning
Frequency: Seasonally
By: Qualified Service Technician
Tools Needed: Protective gloves, glass cleaner.
CAUTION! Handle glass with care. Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Verify batteries have been removed from battery back-up
IPI systems to prevent premature battery failure or
leaking.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 14 for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
Firebox
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Replace fireplace if firebox has been perforated.
Control Compartment and Firebox Top
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Inspect IPI flame sensing rod for soot, corrosion and
deterioration. Polish with fine steel wool or replace as
required.
• Verify that there is not a short in flame sense circuit
by checking continuity between pilot hood and flame
sensing rod. Replace pilot as necessary. (IPI only)
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
Burner Ignition and Operation
Frequency: Annually
By: Qualified Service Technician
(Either cobrahead or SIT)
Figure 3.1 IPI Pilot Flame Patterns
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
15
C. Glass Refractory, Base Pan, Burner and
Valve Assembly Removal
4. Remove the base pan by removing the screws circled
in Figure 3.4.
It may become necessary to remove the glass panels,
base pan, burner and valve assembly. This task should
be performed by a qualified service technician.
5. Remove the burner assembly by removing the two
screws as shown in Figure 3.5. To disengage the burner
from the orifice, slide the burner to the right and lift it out.
6. See Figure 3.6 for valve assembly removal.
1. Remove the media.
2. Remove the side glass panel retainers. See Figure
3.2. Slide the side glass panels out of the appliance
as shown in Figure 3.3.
3. Remove the rear glass panel retainer, shown in Figure
3.2, and lift the rear glass panel out of the appliance.
APPEARANCE
MAY VARY
REAR PANEL RETAINER
SIDE PANEL RETAINERS
Figure 3.4 Base Pan Removal
Figure 3.2 Remove Glass Panel Retainers
Figure 3.3 Glass Panel Removal
16
Figure 3.5 Burner Assembly Removal
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
D. Burner Identification
Appearance of valve
components may vary.
6000CMOD-IPI (NG)
6000CMOD-IPI (LP)
Figure 3.6 Valve Assembly Removal
Figure 3.7 Valve Assembly Removal
8000CMOD-IPI (NG)
8000CMOD-IPI (LP)
Figure 3.8 Valve Assembly Removal
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
17
4
Installer Guide
Getting Started
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
VERTICAL TERMINATION CAP
(SECTION 10.I)
NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE (SECTION 10.G)
STORM COLLAR
(SECTION 10.H)
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)
VENT PIPE (SECTIONS 7 and 8)
ATTIC INSULATION SHIELD (NOT
SHOWN) MUST BE USED HERE TO
KEEP INSULATION AWAY FROM
VENT PIPE IF ATTIC IS INSULATED
(SECTION 8.D)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)
FRAMING/HEADER
(SECTION 5.B)
FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION 8.C)
OPTIONAL
WALL SWITCH
(SECTION 12.C)
MANTEL AND
MANTEL LEG
(SECTION 5.D)
SURROUND
HEARTH EXTENSION
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
18
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
Before installing, determine the following:
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping requirements.
• Electrical wiring requirements.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Framing material
Pliers
Non-corrosive leak check solution
Hammer
Phillips screwdriver
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
Reciprocating saw
Manometer
Flat blade screwdriver
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
One 1/4 in. female connection (for optional fan).
Caulking material (300ºF minimum continuous exposure
rating)
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
19
5
Framing and Clearances
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
A. Selecting Appliance Location
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
NOTE: THE REAR STANDOFF MAY NEED
TO BE REMOVED WHEN VENTING AT 45º
A
1/2 IN.
F
B
ALCOVE
INSTALLATION
A
B
D
C
TOP VENT
ONE 90º ELBOW
B
E
A
6000
8000
B
C
D
E
F
See Section D.
Mantel Projections
22
17-3/4
559
451
22
19-3/4
559
502
in.
51
42
72
mm
1295
1067
1829
in.
55-7/8
49
79
mm
1419
1245
2007
See Section D.
Mantel Projections
Figure 5.1 Appliance Locations
20
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
To further prevent drafts, the wall shield and ceiling firestops should be caulked with caulk with a minimum of
300ºF continuous exposure rating to seal gaps. Gas line
holes and other openings should be caulked with caulk
with a minimum of 300ºF continuous exposure rating or
stuffed with unfaced insulation. If the appliance is being
installed on a cement surface, a layer of plywood may be
placed underneath to prevent conducting cold up into the
room.
B. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
C. Clearances
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
• Failure to maintain airspace may cause overheating and
a fire.
A
E
B
J
F
H
C
D
I
G
* MINIMUM FRAMING DIMENSIONS
A
B
C**
Rough
Opening
(Width)
Rough
Opening
(Height)
Rough
Opening
(Depth)
in.
10
40-1/8
22
42
25
0
0
1/2
1/2
36
mm
254
1019
559
1067
635
0
0
13
13
914
in.
10
42-1/8
22
49
25
0
0
1/2
1/2
36
mm
254
1070
559
1245
635
0
0
13
13
914
Models
6000
8000
D
E
F
G
H
I
J
Rough
Clearance Combustible Combustible Behind
Sides of
Front of
Opening
to Ceiling
Floor
Flooring
Appliance Appliance Appliance
(Width)
* Adjust framing dimensions for interior sheathing (such as sheetrock)
Figure 5.2 Clearances to Combustibles
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
21
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than
the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).
The CMOD door will overlap the appliance. See Figure
5.5 and 5.6.
Combustible Mantels
TO CEILING
18
12
11
10
32
9
25
8
7
19
6
18
5
17
4
16
3
15
14
13
12
2-1/2
11
10
5
Figure 5.5 Appliance Surround
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
3/8 IN.
Note: All measurements in inches.
Note: Measurement is taken from top of the
opening, NOT the top of the fireplace.
1-3/4 IN.
Figure 5.3 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
Combustible Mantel Legs or Wall Projections
INTERIOR WALL
TOP VIEW
3/8 IN.
A
B
Figure 5.6 Door Overlaps Surround
FIREPLACE OPENING
MANTEL LEG OR WALL PROJECTIONS
If
A
B
22
A minimum is ____, then B maximum is_____.
Inches
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
Inches
62
1
87
2
113
3
138
4
164
5
Millimeters
25
51
76
102
127
Millimeters
189


Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
6
Termination Locations
A. Vent Termination Minimum Clearances
WARNING
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
Fire Risk.
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
Gas, Wood or Fuel Oil
Termination Cap
B
A*
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Gas
Termination
Cap **
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
12
*
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
**
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
Figure 6.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
23
O
N
P
R
F
C
V
Q
B
J
H or i
B
V
D
B
V
V
V
H
V
X
G
M
V
A
V
E
H
V
V
V
L
A
V
V = VENT TERMINAL
X = AIR SUPPLY INLET
K
B
C
= 9 inches...................clearance to outside corner
E
= 6 inches...................clearance to inside corner
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
N
O
L
= 12 inches................clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.
M
= 18 inches ...................clearance under veranda, porch, deck,
balcony or overhang
42 inches ................vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the floor.
Figure 6.3 Minimum Clearances for Termination
24
= 18 inches ......... non-vinyl soffit and overhang
42 inches ......... vinyl soffit and overhang
P
= 3 ft. (Canada) ..........not to be installed above a gas meter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
G = 3 ft ...........................clearance to gas service regulator
vent outlet
H
= 9 inches (U.S.A)
12 inches (Canada).clearance to non-mechanical (unpowered) air supply inlet, combustion air
inlet or direct-vent termination
i
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap
must be a minimum of 3 feet below termination.
J
= 7 ft. ......................... On public property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
= 6 inches.................clearance from sides of electrical
service
= 6 inches ........... non-vinyl sidewalls
12 inches ......... vinyl sidewalls
F
K
V
V
= 12 inches.................clearances above grade, veranda,
porch, deck or balcony
= 12 inches.................clearance to window or door that may
be opened, or to permanently closed
window
= 18 inches.................clearance below unventilated soffit
18 inches.................clearance below ventilated soffit
30 inches .................clearance below vinyl soffits and
electrical service
D
K
C
= AREA WHERE TERMINAL IS NOT PERMITTED
A
Electrical
Service
= 8 ft.
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUAL
2 caps
6 feet
1 x Q ACTUAL
3 caps
9 feet
2/3 x Q ACTUAL
4 caps
12 feet
1/2 x Q ACTUAL
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
Measure vertical clearances from this surface.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffic areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.
•
Local codes or regulations may require different
clearances.
•
Vent system termination is NOT permitted in screened
porches.
•
Vent system termination is permitted in porch areas with
two or more sides open.
•
Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
Vinyl protection kits are suggested for use with vinyl siding.
•
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
7
Vent Information and Diagrams
A. Approved Pipe
DO NOT mix pipe, fittings or joining methods from different manufacturers.
Vertical
12
in
.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
8-1/2 in.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
B. Vent Table Key
Horizontal
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
8-1/2 in.
This appliance is approved for use with Hearth & Home
Technologies DVP or SLP venting systems. Refer to Section 16B for vent component information.
Figure 7.1
Description
V1
First section (closest to appliance) of vertical length
V2
Second section of vertical length
H1
First section (closest to appliance) of horizontal length
H2
Subsequent sections of horizontal length
C. Use of Elbows
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
D. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
6.3).
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).
Pipe
DVP4
Effective
Height/Length
Effective Length
Inches
Millimeters
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610
Figure 7.2 DVP Pipe Effective Length
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
25
E. Vent Diagrams
Top Vent - Horizontal Termination
Note: The 6000/8000 series fireplaces can adapt to SLP series
vent pipe, if desired.
WARNING
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles
between ceiling firestops.
• ALWAYS maintain specified clearances around
venting and firestop systems.
• Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away
from vent pipe may cause fire.
When venting off the top of the unit, use a DVP-2SL adapter and a
minimum 48 inch vertical section of SLP series vent pipe.
A DVP-SLP24 adapter may also be used with a 24 inch vertical
section of SLP series vent pipe.
After the 48 inch vertical section, the venting table rules must be
followed. The first 48 inch vertical section is NOT counted as part
of the vertical components in the table. It is still counted as part of
the overall maximum run. All venting table rules for the vent run
must still be followed.
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal
SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal
WARNING
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZCSS termination caps on top vented fireplaces, a
6 inch minimum vertical vent section is required
before installing first elbow.
Top Vent - Horizontal Termination
One Elbow
6000CMOD-IPI
V1 Minimum
Elbow only
8000CMOD-IPI
V1 Minimum
H1 Maximum
H1 Maximum
2 ft
610 mm
2 ft.
610 mm
6 in.
152 mm
4 ft.
1.2 m
1 ft.
Elbow Only
305 mm
3 ft.
914 mm
1 ft.
305 mm
6 ft.
1.8 m
2 ft.
610 mm
6 ft.
1.8 m
1-1/2 ft.
457 mm
10 ft.
3.0 m
3 ft.
914 mm
11 ft.
3.4 m
2 ft.
610 m
15 ft.
4.6 m
4 ft.
1.2 m
20 ft.
6.1 m
2-1/2 ft.
762 mm
18 ft.
5.5 m
3 ft.
914 mm
20 ft.
6.1 m
V1 + H1 = 40 ft. (12.2 m) Maximum
H1 = 20 ft. (6.1 m) Maximum
V1 + H1 = 40 ft. (12.2 m) Maximum
H1 = 20 ft. (6.1 m) Maximum
Note: For corner installations: A 6 inch (152
mm) section of straight pipe may need to
be attached to the appliance before a 90º
elbow, to allow the vent pipe to clear the top
standoffs.
V1
H1
Figure 7.3
26
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
Two Elbows
Note: For corner installations: A 6 inch
(152 mm) section of straight pipe may
need to be attached to the appliance
before a 90º elbow, to allow the vent
pipe to clear the top standoffs.
6000CMOD-IPI
8000CMOD-IPI
V1 Minimum
H1 + H2 Maximum
V1 Minimum
H1 + H2 Maximum
Elbow only
Not allowed
Elbow only
Not allowed
6 in.
152 mm
2 ft.
610 mm
6 in.
152 mm
Not allowed
1 ft.
305 mm
4 ft.
1.2 m
1 ft.
305 mm
2 ft.
610 mm
1-1/2 ft.
457 mm
11 ft.
3.4 m
2 ft.
610 mm
4 ft.
1.2 m
2 ft.
610 mm
17 ft.
5.2 m
3 ft.
914 mm
6 ft.
1.8 m
2-1/2 ft.
762 mm
20 ft.
6.1 m
4 ft.
1.2 m
8 ft.
2.4 m
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 20 ft. (6.1 m) Maximum
V1 = 1 ft. (305 mm) Minimum
6 ft.
1.8 m
12 ft.
3.6 m
10 ft.
3.0
20 ft.
6.1 m
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 20 ft. (6.0 m) Maximum
V1 = 1 ft. (305 mm) Minimum
V1
H2
H1
INSTALLED
HORIZONTALLY
Figure 7.4
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
27
Top Vent - Horizontal Termination - (continued)
Three Elbows
V1 Min.
Elbow only
H1 Max.
V2 Min.
H2 Max.
2 ft.
610 mm
0 in.
0 mm
1 ft.
305 mm
6 in.
152 mm
3 ft
914 mm
6 in.
152 mm
2 ft.
610 mm
1 ft.
305 mm
6 ft.
1.8 m
1 ft.
305 mm
6 ft.
1.8 m
2 ft.
610 mm
11 ft.*
3.4 m*
2 ft.
610 mm
10 ft.*
3.1 m*
3 ft.
914 mm
16 ft *
4.9 m*
3 ft.
914 mm
14 ft.*
4.3 m*
*H1 + H2 = 20 ft. (6.1 m) Maximum
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum
H2
V2
H1
Figure 7.5
28
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
V1
Top Vent - Vertical Termination
Flue Restrictor Instructions
1. Install flue restrictor as shown below.
No Elbow
V1 = 40 ft. Max. (12.4 m)
V1 = 3 ft. Min. (914 mm)
FLUE
RESTRICTOR
Note: If installing a vertical vent/
termination off the top of the appliance, the flue restrictor should be
used. See Figure 7.9.
Figure 7.7
V1
2. Break the flue restrictor into two pieces. Do this by
bending the part back and forth until it breaks (see
Figure 7.8).
BREAK
HERE
Figure 7.6
Figure 7.8 Flue Restrictor
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
29
Top Vent - Vertical Termination (continued)
4. Center the Flue Restrictor on vent and secure in place
by using two self-tapping screws (see Figure 7.10).
3. Match the amount of vertical you have in the system
with the chart to find the appropriate position to set the
Flue Restrictor (see Figure 7.9).
5. Reinstall the Exhaust Shield.
Vertical
TOP VENT
NG
LP
4 ft.
1-1
No
Restrictor
8 ft.
2-2
1-2
15 ft.
3-3
3-2
20 ft.
3-3
3-3
25 ft.
3-3
3-3
30 ft.
3-4
3-4
35 ft.
3-4
3-4
40 ft.
3-4
4-4
1
2
3
4 5
SETTING
1
2
3
4 5
Figure 7.10
Figure 7.9
Note: If the DVP-2SL or DVP-SLP24 adapter is used with
SLP pipe, you MUST subtract one number from the table
above.
Example: Top vent 40 ft vertical with DVP pipe = 4-4
Top vent 40 ft vertical with SLP pipe = 3-3
V1
Two Elbows
H1 Maximum
Elbow only
V1 + V2 Min.
2 ft.
610 mm
*
*
*
6 in.
152 mm
6 ft.
1.8 m
*
*
*
2 ft.
610 mm
11 ft.
3.4 m
*
*
*
3 ft.
914 mm
16 ft.
4.9 m
*
*
*
4 ft.
1.2 m
20 ft.
6.1 m
*
*
*
V1 + V2 + H1 = 50 ft. (15.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 50 ft (15.2 m)
V2
H1
V1
Figure 7.11
30
V2
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
Top Vent - Vertical Termination - (continued)
V1
Three Elbows
H1 + H2
Elbow only
V2
V1 + V2 Minimum
H1 + H2 Maximum
1 ft.
305 mm
*
*
*
1 ft.
305 mm
6 in.
152 mm
2 ft.
610 mm
*
*
*
2 ft.
610 mm
1 ft.
305 mm
2 ft.
610 mm
*
*
*
2 ft.
610 mm
2 ft.
610 mm
4 ft.
1.2 m
*
*
*
4 ft.
1.2 m
3 ft.
914 mm
9 ft.
2.7 m
*
*
*
9 ft.
2.7 m
4 ft.
1.2 m
18 ft.
5.5 m
*
*
*
18 ft.
5.5 m
H1 + H2 = 20 ft. (6.1 m) Maximum
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.12
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
31
8
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
Combustible Wall Penetration
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
Failure to keep insulation or other material away from
vent pipe may cause over heating and fire.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
‡ DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
‡ ,f wall thickness is less than 4 in. the e[isting heat shields must be field trimmed. ,f
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
‡ SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
‡ ,f wall thickness is less than 4-3/8 the e[isting heat shields must be field trimmed.
,f wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B.)
attached to them.
• See Section 10.L for information for regarding the installation of a horizontal termination cap.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter
one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
WALL
* When using SLP or SL-D pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are: Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
10 in.
12 in.
B
A*
6000
8000
in.
mm
in.
mm
A*
42-3/4
1086
44-3/4
1137
B
41-3/4
1060
44-1/8
1111
* Shows center of vent framing hole for top or rear venting. The center of the
hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.
Figure 8.2 Wall Penetration
32
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 8.3).
ATTIC ABOVE
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 8.3).
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
A
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.4.
• Secure with three fasteners on each side.
A
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
PIPE
A
DVP
10 in. (254 mm)
SLP
9 in. (229 mm)
Figure 8.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
INSTALLED BELOW CEILING
CEILING FIRESTOP
INSTALLED ABOVE CEILING
Figure 8.4 Installing the Attic Shield
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
33
D. Install Attic Insulation Shield
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
Attic shields must meet specified clearance and be secured in place.
Flat Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
INSERT 3
SCREWS
BEND 3 TABS
OUTWARD TO
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
CLEARANCE
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90º to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90º around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Figure 8.5 Attic Insulation Shield
E. Installing the Optional Heat-Zone® Gas Kit
• Remove the knockout from the fireplace and discard it
(see Figure 8.6).
• Center the duct collar around the exposed hole and
attach it to the fireplace with 3 screws. Note: Do this
BEFORE final positioning of fireplace.
• Determine the location for the air register/fan housing
assembly.
Vaulted Ceiling Installation
• Remove one shield from box.
Reference the Heat-Zone® Gas kit instructions for the
remaining installation steps.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) to fit your ceiling pitch. Snip cut edge to recreate
1 in. bend tabs all the way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
HEAT-ZONE® GAS
ATTACHES HERE
• Bend the remaining bottom tabs inward 90º to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90º around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
34
Figure 8.6 Heat Zone Cover Plate
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
9
Appliance Preparation
A. Top Vent
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
Figure 9.4 Remove the insulation basket and white insulation from the center vent pipe.
Figure 9.1 Cut the seal cap strap across the rectangles
next to the disk. For rear vent, skip this step.
Figure 9.2 Remove the white gasket material covering
the seal cap.
Figure 9.5 Remove the insulation from the outer vent
pipe. For rear venting there is no insulation in the outer
vent pipe.
Figure 9.6 To attach the first section of vent pipe, make
sure to use the fiberglass gasket in the manual bag to seal
between the first vent component and the outer fireplace
wrap. Use 2 self tapping screws to secure the gasket to
the outer wrap.
Figure 9.3 Remove the seal cap.
Secure the first section of venting to the fireplace by screwing through the two straps left over from cutting the seal
cap strap in step 2.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
35
B. Installing the Non-combustible Board
The factory supplied non-combustible board spans the
distance from the top of the fireplace to the center of the
framing header. This board must be used. See Figure 9.7.
WARNING! Risk of Fire! Non-combustible board must
be installed across the top of the fireplace per Figure 9.7.
A
B
HEADER
Note: Diagonal dimensions (A) and (B) must be within
1/4 inch of each other.
Figure 9.7 Non-combustible Board
Figure 9.8 Positioning the Appliance Squarely
C. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air space clearance may cause
overheating and fire.
The diagram shows how to properly position and secure
the appliance (see Figure 9.9). Nailing tabs are provided
to secure the appliance to the framing members.
NAILING TABS
(BOTH SIDES)
• Bend out nailing tabs on each side.
• Place the appliance into position.
PILOT HOLES
• Keep nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
• “Square” the unit by securing diagonal dimensions to
within 1/4 inch of each other. See Figure 9.8.
Figure 9.9 Proper Positioning and Securing of an Appliance
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
36
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
10
Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with high temperature
silicone (minimum of 300ºF continuous exposure rating), including the slip section that connects directly to the horizontal termination cap.
Figure 10.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1
A
Lances
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Assemble Pipe Sections
B
Figure 10.3
Figure 10.2
Note: Make sure that the seams are not aligned to prevent
Per Figure 10.2:
unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90º and 45º elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
Figure 10.4 Seams
INCORRECT
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
37
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.6.
• Attach a DVP-2SL or DVP-SLP24 adapter to the starting
collar of the appliance.
• Slide together to the desired length.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 10.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
Caulk with a minimum of 300ºF continuous exposure
rating may be used to hold the part in place.
Pilot hole
• Continue adding vent components, locking each
succeeding component into place.
Figure 10.6 Slip Section Pilot Holes
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 10.7.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with high temperature silicone
(minimum of 300ºF continuous exposure rating), including
the slip section that connects directly to the horizontal termination cap.
• Apply a bead of silicone sealant (minimum of 300ºF continuous exposure rating), inside the female outer pipe
joint prior to joining sections. See Figure 10.1.
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 10.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed using
a high temperature silicone sealant (minimum of 300ºF
continuous exposure rating),.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
Figure 10.5 Adding Venting Components
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
38
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs of DVP pipe must be supported every 8 ft.
(2.44 m) after the 25 ft. (7.62 m) maximum unsupported
rise.
• Rotate either section (see Figure 10.10) so the seams
on both pipe sections are aligned as shown in Figure
10.11.
• Vertical runs of SLP pipe must be supported every 8 ft.
(2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal sections must be supported every 5 feet
(1.52 m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support vent sections. See Figures 10.8
and 10.9.
• Wall shield firestops may be used to provide horizontal
support vent sections.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 10.10 Rotate Seams for Disassembly
120º
Figure 10.11 Align and Disassemble Vent Sections
Figure 10.8 Securing Vertical Pipe Sections
120º
Figure 10.9 Securing Horizontal Pipe Sections
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
39
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
high temperature silicone (minimum of 300ºF continuous
exposure rating) to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
A decorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 10.12
• Remove shingles or other roof covering as necessary
to cut the rectangular hole for the support box. Cut the
hole 1/8 in. (3 mm) larger than the support box outline.
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
10.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
40
Figure 10.13
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
G. Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 10.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.15.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Figure 10.15
GAS DIRECT VENT
TERMINATION CAP
H. Assemble and Install Storm Collar
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................. 2.5
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
• Connect both halves of the storm collar with two screws
(see Figure 10.16).
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
• Slide the assembled storm collar down the pipe section
until it rests on the roof flashing (see Figure 10.17).
• Caulk around the top of the storm collar (see Figure 10.23).
* 3 foot minimum in snow regions
Figure 10.14 Minimum Height From Roof To Lowest Discharge
Opening
Figure 10.16 Assembling the Storm Collar
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.15.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
Figure 10.17 Assembling the Storm Collar Around the Pipe
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
41
I. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 10.23).
TERMINATION CAP
K. Heat Shield Requirements for Horizontal
Termination
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.25).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.25.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
STORM
COLLAR
SCREWS
CAULK
• Use an extended heat shield if the finished wall thickness
is greater than 7-1/4 in. (184 mm).
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 10.23
J. Install Decorative Wall Components (SLP
only)
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the wall shield firestop.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
10.24.
Figure 10.24 Wall Thimble
42
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
L. Install Horizontal Termination Cap (DVP
and SLP Pipe)
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
SLIP SECTION
CAN BE EXTENDED
• Flash and seal as appropriate for siding material at
outside edges of cap.
INNER VENT
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
SHEATHING
OUTER VENT
INTERIOR
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
WALL SHIELD
FIRESTOP
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 10.25 Venting through the wall
Cap Specification Chart
(depth without using additional pipe sections)
6000
Series
8000
Series
DVP-TRAPK1
Top Vent Depth
2-3/4 in. to 4-5/8 in.
DVP-TRAPK2
Top Vent Depth
5-1/8 in. to 9-1/8 in.
DVP-HPC1
Top Vent Depth
2-3/4 in. to 4-7/8 in.
DVP-HPC2
Top Vent Depth
4-7/8 in. to 9 in.
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
43
11
Gas Information
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 16 for location of gas line
access in appliance.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
• Gas line may be run through knockout(s) provided.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• The gap between supply piping and gas access
hole may be caulked with caulk with a minimum of
300ºF continuous exposure rating or stuffed with noncombustible, unfaced insulation to prevent cold air
infiltration.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
• Pressure requirements are:
Natural Gas
Propane
Minimum inlet pressure
5.0 in. w.c.
11.0 in. w.c.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Maximum inlet pressure
10.0 in. w.c.
13.0 in. w.c.
• A small amount of air will be in the gas supply lines.
Manifold pressure
3.5 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.
Gas Pressure
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in. (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
44
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
12
Electrical Information
A. Wiring Requirements
B. IntelliFire PlusTM Ignition System Wiring
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• Wire the appliance junction box to 110-120 VAC. This is
required for use of optional accessories (standing pilot
ignition) or proper operation of the appliance (IntelliFire
PlusTM ignition).
• Wire the appliance junction box to 110 VAC for proper
operation of the appliance.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• Refer to Figure 12.1, IPI Wiring Diagram.
• This appliance is equipped with an IntelliFire PlusTM
control valve which operates on a 6 volt system.
• Plug the 6 volt transformer plug into the appliance junction
box to supply power to the unit OR install 4 AA cell
batteries (not included) into the battery pack before use.
C. Optional Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
• Hearth & Home Technologies recommends that IntelliFire PlusTM wireless controls be used for their features
and functionality with the IntelliFire PlusTM ignition system.
• A standard ON/OFF switch is compatible.
FLAME
SENSE
IGNITER
TO JUNCTION
BOX (110V)
MODULE
FLAME
MODULATION
RC100
RC200
RC300
(OPTIONAL WALL CONTROLS)
ORANGE
(PILOT)
BATTERY PACK
6V DC
GREEN
(MAIN)
BLACK
RED
THERMOSTAT WIRE
ASSEMBLY / WALL
SWITCH WIRE
BROWN
GROUND
Figure 12.1 IPI Wiring Diagram
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
45
D. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
Romex
Connector
14/2WG
WARNING! Risk of Shock! Replace damaged wire with
type 105º C rated wire. Wire must have high temperature
insulation.
Cover Plate
outside firebox
E. Junction Box Installation
HT
WHT B
LK
BLK
W
If the box is being wired from the INSIDE of the appliance:
• Remove the screw attaching the junction box/receptacle to
the outer shell, rotate the junction box inward to disengage
it from the outer shell (see Figure 12.2).
• Pull the electrical wires from outside the appliance through
the opening into the valve compartment and secure wires
with a Romex connector. See Figure 12.2.
• Make all necessary wire connections to the junction box/
receptacle and reattach the junction box/receptacle to the
outer shell.
Copper
ground attached
to GRN screw with
GRN wire
GRN wire
inside box
NOTICE: DO NOT wire
110 VAC to wall switch.
Figure 12.2 Junction Box Detail
F. Wall Switch Installation for Fan (Optional)
• The power supply for the appliance must be brought into
a switch box.
Switch
Minimum 14-3 AWG
with Ground
Red
Black
White
Green
Junction Box
• The power can then be supplied from the switch box to the
appliance using a minimum of 14-3 with ground wire.
Switch Box
• At the switch box connect the black (hot) wire and red
(switch leg) wire to the wall switch as shown.
• At the appliance connect the black (hot), white (neutral)
and green (ground) wires to the junction box as shown.
• Add a 1/4 in. insulated female connector to the red (switch
leg) wire, route it through the knockout in the face of the
junction box, and connect to the top fan switch connector
(1/4 in. male) as shown.
46
Black
White
Green
Red
Black
White
Green
If the box is being wired to a wall mounted switch for use
with a fan (See Figure 12.3):
Knockout
Red
Figure 12.3 Junction Box Wired to Wall Switch or BC10
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
Power
Supply
Wires
13
Finishing
A. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials
(i.e., steel studs, concrete board, etc.)
The CMOD door will overlap the appliance. See Figure
13.3 and 13.4.
Combustible Mantels
Note: All
measurements
in inches.
TO CEILING
18
12
11
10
32
9
25
8
7
19
6
18
5
17
4
16
3
15
14
13
12
2-1/2
11
10
5
Figure 13.3 Appliance Surround
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
Note: Measurement is taken from top of the opening,
NOT the top of the fireplace.
Figure 13.1 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
3/8 IN.
Combustible Mantel Legs or Wall Projections
1-3/4 IN.
INTERIOR WALL
TOP VIEW
A
B
FIREPLACE OPENING
3/8 IN.
MANTEL LEG OR WALL PROJECTIONS
If
A
B
A minimum is ____, then B maximum is_____.
Inches
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
Inches
62
1
87
2
113
3
138
4
164
5
Millimeters
25
51
76
102
127
Millimeters
Figure 13.4 Door Overlaps Surround
189


Figure 13.2 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
47
B. Facing Material
C. Finish and Sealing Joints
• Metal front faces may be covered with non-combustible
materials only.
All joints between the finished wall sheathing and the appliance must be sealed with non-combustible materials.
Sealants, such as caulk or mastic used to seal the gap
between the wall and the fireplace, should be rated at a
minimum continuous exposure to 300ºF.
• Facing and/or finishing materials must not interfere with
air flow through louvers, operation of louvers or doors,
or access for service.
• Facing and/or finishing materials must never overhang
into the glass opening.
• Observe all clearances when applying combustible
materials.
• Seal joints between the finished wall and appliance top
and sides using a 300ºF minimum sealant. Refer to
Figure 13.3.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.
Finishing Around Opening with Gypsum Wallboard
Gypsum wallboard (drywall) joints adjacent to the fireplace opening, including the non-combustible board on
the appliance, require special attention to minimize cracking. When installing gypsum wallboard around the fireplace, install the hole for the fireplace opening in a single
wallboard sheet, if possible. This will minimize the joints
adjacent to the fireplace opening.
Tape wall board joints around the fireplace opening with
fiberglass-mesh tape. It will provide a more crack-resistant joint than paper tape. Fill, smooth and finish wall
joints with chemically setting-type joint compound. It will
provide a more crack-resistant joint than air-drying lightweight compound.
Painting
B
FACTORY-INSTALLED NON-COMBUSTIBLE BOARD
DO NOT REMOVE
If desired finishing includes a painted wall, 100% acrylic
latex with compatible primer is recommended around this
appliance. Oil-based or standard acrylic paints may discolor due to heat exposure.
A
6000
8000
A
B
inches
39-3/4
41
millimeters
1010
1041
inches
41-3/4
48
millimeters
1060
1219
Figure 13.5 Noncombustible Facing Diagram
48
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
D. Door Selection
Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used.
The CMOD door can not be used if the appliance is installed directly on the floor. See Figure 13.6 and 13.7.
Folio Door Application
If the appliance is installed on the floor or level with an elevated hearth, the Folio Door MUST be used. The CMOD door
is not compatible with this type of installation as a minimum elevation of 1 inch is required on the bottom of the appliance.
WALL
WALL
FOLIO DOOR
FLOOR
/ ELEV
ATED H
E
ARTH
FLOOR
/ ELEV
ATED H
E
ARTH
Figure 13.6 Appliance Installed on Floor or Elevated Hearth
CMOD Door Application
If the appliance is installed at a minimum of 1 inch above the floor, the CMOD door can be used. The CMOD door OVERLAPS the sides, top and bottom of the appliance surround. See Figure 13.3 and 13.4 for dimensions.
WALL
CMOD DOOR
WALL
FLOOR/E
LEVATE
D HEAR
TH
FLOOR/E
LEVATE
NOTE: THE APPLIANCE MUST BE ELEVATED A MINIMUM
OF 1 INCH IN ORDER TO USE THE CMOD DOOR.
D HEAR
TH
Figure 13.7 Appliance Installed Off the Floor
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
49
Only doors certified for use with this appliance model
may be used. Contact your dealer for a list of doors that
may be used. Once you have determined what kind of
door and finishing material is going to be used on the
fireplace, you may use the table below which shows the
door models and the finishing material thickness allowed.
DOOR
FIT
FINISH MATERIAL
THICKNESS
SEE
FIGURE
CMOD-8-BK
Overlap
1 inch thick or less
13.8
CMOD-8-GY
Inside
1-4 inches maximum
13.9
CMOD-6-BK
Overlap
1 inch thick or less
13.8
CMOD-6-GY
Inside
1-4 inches maximum
13.9
FOLIO
Inside
Any
13.10
Finishing Material:
1 Inch Thick or Less - Overlap Fit Method
DOOR
1 in. MAX.
FINISHING MATERIAL
(TOP EDGE)
Finishing materials 1 inch maximum thick.
Stop finishing material flush with opening.
NON-COMBUSTIBLE
FINISHING MATERIAL
Figure 13.8 Finishing Material 1 Inch Thick or Less
50
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
Finishing Material Thickness:
Greater than 1 Inch - Inside Fit Method
8000 Models
NOTICE: Non-combustible finishing materials greater than
one inch require the inside fit method.
NON-COMBUSTIBLE
FINISHING MATERIAL
6000 Models
Inches
Millimeters
Inches
Millimeters
A
48-13/16
1240
41-13/16
1062
B
38-3/8
975
36-3/8
924
C
49-1/16
1246
42-1/16
1068
D
39-1/4
997
37-1/4
946
E
3/8
10
3/8
10
Finishing Material:
0 - 4 Inches - Inside Fit Method
NON-COMBUSTIBLE
FINISHING MATERIAL
FINISHING
MATERIAL
FINISHING
MATERIAL
DOOR
A
(Outside door width)
C
(Includes 1/8 in. opening each side of door)
B
D
A
(Outside door width)
C
DOOR
(Includes 1/8 in. opening each side of door)
E
FINISHING MATERIAL
Finishing Material Thickness Greater than 1 Inch
B = Top of door to bottom of fireplace.
D = Bottom of Finishing Material to Bottom of Fireplace
FINISHING MATERIAL
Figure 13.10 Folio Inside Fit
Figure 13.9 Finishing Material Thickness Greater Than One Inch
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
51
14
Appliance Setup
A. Remove Fixed Glass Assembly
See Section 14.G.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
E. Glass Panel Installation
Figure 14.2 Install Side Glass Panels
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation.
CAUTION! Glass is fragile. Handle with care.
1. Install the rear glass panel as shown in Figure 14.1.
the panel retainers and screws are included in the appliance manual bag.
SIDE RETAINERS
Note: Screw the three glass panel retainers to the firebox using the EXISTING pilot holes.
2. Slide the side glass panels in positions as shown in
Figure 14.2.
3. Figure 14.3. shows the glass panels installed properly.
Figure 14.3 Install Side Retainers
REAR RETAINER
Figure 14.1 Install Rear Retainer
52
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
F. Media Placement
WARNING! Risk of Explosion! Follow media placement
instructions. Improperly placed media interfere with proper
burner operation.Fireplace will not function properly.
Delayed ignition may occur.
WARNING! Choking Hazard! Keep media out of reach
of children.
• DO NOT place media in pilot opening.
• DO NOT place media in a position that it may fall into
the pilot opening.
• DO NOT use any media other than the media supplied
with this fireplace or listed in Service Parts Section in
this manual.
• DO NOT use more than 14 lb. of media per 8000CMODIPI or 12 lb. per 6000CMOD-IPI fireplace. Note: One bag
of glass contains 7 lbs.
6000CMOD-IPI: Extra 2 lbs. may be saved for future use.
1. Place media evenly on the base pan. Figure 14.9
shows properly placed media.
2. The media can only be placed in the shaded areas as
shown in Figure 14.7 and Figure 14.8.
Figure 14.5 Rock Fixture Assembly Installed
THIS JIG MUST BE USED FOR
STONE PLACEMENT
• REMOVE BEFORE BURNING
• DO NOT DISCARD
3. Do not apply media over the pilot opening. See Figure
14.7 and Figure 14.8.
4. The rock fixture assembly is factory installed in the
appliance. See Figure 14.4 and Figure 14.5.
5. After the media is properly installed, carefully remove
the rock fixture assembly. Do not allow any media to
fall into the opening. See Figure 14.6. Store the rock
fixture assembly under the appliance for future use.
REMOVE SCREW
Figure 14.6 Remove Rock Fixture Assembly
Figure 14.4 Rock Fixture Installed
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
53
BURNER
NO MEDIA ON
PILOT OPENING
(WHITE AREA)
Figure 14.7 Placement of Media
BURNER
NO MEDIA ON
PILOT OPENING
(WHITE AREA)
Figure 14.8 Placement of Media
Figure 14.9 Proper Placement of Media
54
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
G. Fixed Glass Assembly
I. Air Shutter Setting
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is
set at the factory for minimum vertical vent run. Adjust air
shutter for longer vertical runs. See Figure 14.8.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
• Loosen the wing nut.
Removing Fixed Glass Assembly
• Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 14.7).
Replacing Fixed Glass Assembly
• Move the air handle to the left to open the air shutter.
• Move the air handle to the right to close the air shutter.
• Tighten the wing nut.
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
Appearance of
components may vary.
• Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
AIR SHUTTER
WING NUT
LATCHES
(BOTH BOTTOM
AND TOP)
Figure 14.8 Air Shutter
GLASS
ASSEMBLY
Air Shutter Settings
Figure 14.7 Fixed Glass Assembly
NG
LP
6000
Fully Closed
Fully Open
8000
Fully Open
Fully Open
H. Install Trim and/or Surround
• Install optional trim kits and/or surrounds using the
instructions included with the accessory.
• Use non-combustible materials to cover the gap between
the sheet rock and the appliance (when applicable to the
model).
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
55
15
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. IntelliFire PlusTM Ignition System
Symptom
Possible Cause
1. Pilot won’t light.
A. Incorrect wiring.
The ignitor/module
makes noise, but no
B. Loose connections or electrical
spark.
shorts in the wiring.
2. Pilot won’t light,
there is no noise or
spark.
3. Pilot sparks, but
Pilot will not light.
56
Corrective Action
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify igniter and flame sense wires are not grounding
out to metal chassis, pilot burner, pilot enclosure, mesh screen if
present, or any other metal object.
C. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
A. No power, transformer installed
incorrectly or depleted batteries.
Verify that transformer is installed and plugged into module. Check
voltage of transformer at connection to module. Acceptable readings of a good transformer are between 6.4 and 6.6 volts AC. Battery power supply voltage must be at least 4 volts. If below 4 volts,
replace batteries.
B. A shorted or loose connection in
wiring configuration or wiring harness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
Verify that 110/VAC power is “ON” to junction box.
D. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.
B. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
D. Pilot valve solenoid.
Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.
If below 1.5 volts, replace module. If 1.5 volts or greater, replace
valve.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
Troubleshooting (continued)
Symptom
4. Pilot lights but continues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
Possible Cause
A. A shorted or loose connection in flame
sensing rod.
Corrective Action
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify
flame sense or igniter wires are not grounding out to metal
chassis, pilot burner, pilot enclosure or screen if present, or
any other metal object.
B. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is enflame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. With a multimeter, verify that current in series between module and
sense lead is at least 0.14 microamps. Verify correct pilot
orifice is installed and gas inlet is set to pressure specifications. Polish flame sensing rod with fine steel wool to
remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to the
module.
D. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod
is not cracked, damaged, or loose. Verify connection from
flame sensing rod to white sensor wire. Polish flame sensing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multi-meter with ohms set at lowest range.
Replace pilot if any damage is detected.
E. Module.
Turn ON/OFF rocker switch or wall switch to OFF position.
Remove ignitor wire “I” from module. Place ON/OFF rocker
switch or wall switch in ON position. If there is no spark at “I”
terminal module must be replaced. If there is a spark at “I”
terminal, module is fine.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
57
16
Reference Materials
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
L
J
K
N
TOP VIEW
H
GAS LINE
ACCESS
R
I
C
D
G
O
E
Q
B
A
P
LEFT SIDE
F
RIGHT SIDE
FRONT VIEW
Location
Inches
Millimeters
Location
Inches
Millimeters
A
41
1041
J
21
533
B
36-1/8
918
K
11-11/16
297
C
33-1/2
851
L
28-1/2
724
D
34-5/8
879
M
14-1/4
362
E
2-1/4
57
N
8-1/2
216
F
9-11/16
246
O
2-7/8
73
8-1/2
216
G
26-7/8
683
P
H
6 dia
152
Q
1
25
I
39-7/8
1013
R
40-7/8
1038
Figure 16.1 Appliance Dimensions-6000 Models
58
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
L
M
J
K
N
TOP VIEW
H
GAS LINE
ACCESS R
I
C
D
G
E
Q
O
B
P
F
A
LEFT SIDE
RIGHT VIEW
FRONT VIEW
Location
Inches
Millimeters
Location
Inches
Millimeters
A
48
1219
J
21
533
B
43-1/8
1096
K
11-11/16
297
C
35-1/2
902
L
35-1/2
901
D
36-5/8
930
M
17-3/4
451
8-1/2
216
E
2-3/8
60
N
F
9-15/16
252
O
2-7/8
73
G
28-7/8
734
P
8-1/2
216
H
6
152
Q
1
25
I
41-7/8
1064
R
42-7/8
1089
Figure 16.2 Appliance Dimensions-8000 Models
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
59
B. Vent Components Diagrams
Pipe
DVP4
Effective
Height/Length
DVP Pipe (see chart)
Effective Length
Inches
Millimeters
4
102
10-1/2 in.
(267 mm)
45 °
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
10-7/8 in.
(276 mm)
DVP45 (45º Elbow)
4-7/8 in.
(124 mm)
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610

11-3/8 in.
(289 mm)
10 in.
(254 mm)
1 in.
(25 mm)
7-3/8 in.
(187 mm)
1-1/4 in. (32 mm)
10 in.
(254 mm)
9-1/4 in.
(235 mm)
Assembled
Height: 24 in./610 mm
Diameter: 10 in./254 mm
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
DVP-AS2
DVP-FS (Ceiling Firestop)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
1 in.
(25 mm)
8 in.
(203 mm)
14 in.
(356 mm)
UP
5 in.
(127 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.2 DVP vent components
60
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
12 in.
(305 mm)
DVP-TRAP
Horizontal Termination Cap
Max
Effective
Length
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
Trap1
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
Trap2
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
DVP-HPC1
DVP-HPC2
Figure 16.3 DVP vent components
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
61
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(337 mm)

24-5/8 in.
(625 mm)
27-1/2 in.
(699 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(337 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
5 in.
(127 mm)
13-3/4 in.
(349 mm)
11-7/8 in.
(302 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-TRAPFL
Flashing
DVP-HSM-B
Extended Heat Shield
Figure 16.4 DVP vent components
COOL-ADD
Cap Shield
13-7/8 in.
(352 mm)
26 in.
660 mm
62
5 in.
(127 mm)
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DRC-RADIUS
Cap Shield
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12

B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
12 in.
(305 mm)
12 in.
305 mm
DVP-TB1
BasementVent Cap
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
PVK-80
(Not compatible with Intellifire Plus™.)
(For use with IPI and DSI appliances only.)
14 in.
(356 mm)
16-7/8 in.
(429 mm)
12 in.
(305 mm)
7-1/8 in.
(181 mm)
12-1/8 in.
(314 mm)
8-3/4 in.
(222 mm)
1 in.
(25 mm)
7-1/4 in.
(184 mm)
14 in.
(356 mm)
3/8 in. (10 mm)
1 in. (25 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
1-5/8 in.
(41 mm)
DVP-HPC
High Performance Cap
DVP-FBHT
FireBrickTermination Cap
Figure 16.5 DVP vent components
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
63
B. Vent Components Diagrams (continued)
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
8-3/8 in.
213 mm
5-1/2 in.
140 mm
87°
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
WARNING
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZCSS termination caps on top vented fireplaces, a
6 inch minimum vertical vent section is required
before installing first elbow.
DVP-HRC-SS
DVP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
Optional Wire Harness
13-5/8 IN.
346 mm
DESCRIPTION
12-1/2 IN.
318 mm
PART NUMBER
10 ft. PV Wire Harness
PVI-WH10
20 ft. PV Wire Harness
PVI-WH20
40 ft. PV Wire Harness
PVI-WH40
60 ft. PV Wire Harness
PVI-WH60
80 ft. PV Wire Harness
PVI-WH80
100 ft. PV Wire Harness
PVI-WH100
20-3/4 IN.
527 mm
Note: Wire harnesses required to power the PVI-SLP
connect to the appliance and are ordered separately from
PVI-SLP. Contact your dealer to order.
PVI-SLP
Power Vent Inline
16 IN.
406 mm
4-1/2 IN.
114 mm
15 IN.
(381 mm)
9-3/16 IN.
(233 mm)
13-5/8 IN.
(346 mm)
12-1/2 IN.
(318 mm)
Figure 16.6 Vent Components
64
16-11/16 IN.
424 mm
SLP-LPC
SLP Low Profile Cap
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
16-11/16 IN.
(424 mm)
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
6-1/2 in.
165 mm
9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
SLP45
45° Elbow
6-5/8 in.
168 mm
9-7/8 in.
251 mm
SLP90
90° Elbow
Effective Height/Length
Effective
Height/
Length
Pipe
inches
mm
SLP4
4
102
SLP6
6
152
SLP12
12
305
SLP24
24
610
SLP36
36
914
SLP48
48
1219
SLP6A
2-6
51-152
SLP12A
2 - 12
51-305
DVP-SLP24
Adapter
SLP PIPE
SLP-HVS
Horizontal Pipe
Support
SLP-FS
Ceiling Firestop
SLP-WS
Wall Shield Firestop
Figure 16.7 SLP Series Vent Components
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
65
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm)
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a
DVP-HSM-B will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Max
Effective
Length
12 in.
(305 mm)
SLP-TRAP
Horizontal Termination Cap
SLK-SNKD
Snorkel
Termination Cap
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-3/4 in.
79 mm
121 mm
Trap1
5-1/4 in.
9-1/4 in.
133 mm
235 mm
Trap2
SLP-TVHW
Vertical
Termination Cap
26 in.
660 mm
DVP-2SL
Adapter
SLP-DCF-BK
Ceiling Firestop
Black
DVP-HSM-B
Extended Heat Shield
SLP-WT-BK
Wall Thimble-Black
Figure 16.8 SLP Series Vent Components
66
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
C. Service Parts
6000CMOD-IPI
Beginning Manufacturing Date: Aug 2010
Ending Manufacturing Date:______
36” Modern Direct Vent Fireplace
1
6
8
3
7
2
4
4.1
4.2
5
11
4.4
4.3
10
9
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
1
Non-Combustible Board
2166-136
2
Refractory Bracket
3
Rock Fixture Assembly
2241-040
4
Base Pan Assembly
2241-015
4
Base Pan Back
2241-114
4
Base Pan Front
2241-101
4
Pilot Hood
2241-117
4
Pilot Shield
Qty 2 req
2241-115
Y
Stainless
2241-116
NG
2241-007
Y
LP
2241-008
Y
5
Burner Assembly
6
Glass Refractory, Back
7
Glass Refractory, Sides
Qty 2 req
2241-201
8
Glass Retainer Clips
Pkg of 25
060-235-25
9
Surround Assembly
2166-019
10
Glass Assembly
GLA-6000G
Y
11
Junction box
4021-013
Y
2241-200
Y
Additional service part numbers on following page.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
67
C. Service Parts
8000CMOD-IPI
Beginning Manufacturing Date: Aug 2010
Ending Manufacturing Date:______
42” Modern Direct Vent Fireplace
1
6
8
3
7
2
4
4.1
4.2
5
11
4.4
4.3
10
9
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
1
Non-Combustible Board
2
Refractory Bracket
2170-136
3
Rock Fixture Assembly
2241-040
4
Base Pan Assembly
2242-015
4
Base Pan Back
2242-114
4
Base Pan Front
2242-101
4
Pilot Hood
2241-117
4
Pilot Shield
Qty 2 req
2241-115
Stainless
2241-116
NG
2242-007
Y
LP
2242-008
Y
5
Burner Assembly
6
Glass Refractory, Back
7
Glass Refractory, Sides
Qty 2 req
8
Glass Retainer Clips
Pkg of 25
9
Surround Assembly
2170-019
10
Glass Assembly
GLA-950TR
Y
11
Junction box
4021-013
Y
2242-200
2242-201
060-235-25
Additional service part numbers on following page.
68
Y
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
Y
6000CMOD-IPI, 8000CMOD-IPI
C. Service Parts
Beginning Manufacturing Date: Aug 2009
Ending Manufacturing Date: ______
#12 Valve Assembly
12.2
12.1
12.3
12.4
12.5
12.6
12.14
12.7
12.9
12.8
12.10
12.11
12.12 12.13
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
12.1
COMMENTS
PART NUMBER
Shutter Bracket Assembly
2118-121
Y
Pilot Assembly, NG
2090-012
Y
Pilot Assembly, LP
2090-013
Y
12.3
Pilot Bracket
2241-109
12.4
3-Hole Grommet
2118-104
12.5
Valve Bracket
2118-104
12.6
Flex Ball Valve Assembly
302-320A
Y
Valve, NG
2166-302
Y
Valve, LP
2166-303
Y
303-315/5
Y
12.2

DESCRIPTION
Stocked
at Depot
12.7
12.8
Male Connector
Pkg of 5
12.9
Bulkhead w/FlexTube
7000-156
Y
12.10
Control Module, Gray
2166-306
Y
12.11
Wire Harness
2166-304
Y
12.12
Switched DC Regulator
2166-305
Y
12.13
Jumper Wire
2187-198
Y
12.14
Thermostat Wire Assembly
2118-170
Y
582-840
Y
582-855
Y
582-835
Y
582-854
Y
Orifice, NG (#40C)
6000CMOD-IPI
Orifice, LP (#55C)
Orifice, NG (#35C)
8000CMOD-IPI
Orifice, LP (#54C)
Additional service part numbers on following page.
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
69
6000CMOD-IPI, 8000CMOD-IPI
Service Parts List
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Battery Pack**
Stocked
at Depot
PART NUMBER
2166-323
Y
**Fuse for battery pack can be sourced locally, not a warranty item. Specs are 500mA~10A 3/4” long
Flue Restrictor
385-128
Gasket Assembly
2166-081
Includes Vent, Seal Cap, Burner Neck, Shutter Bracket,
Manifold and Valve Plate gaskets
Glass Latch Assembly
Media, Standard, 7 lb bags
Media (Optional 14 LB bag)
Pkg of 2
Clear (Qty 2 req)
Conversion Kit, LP
Conversion Kit, NG
Conversion Kit, LP
70
Y
4065-111
Amber
MEDIA-AMBER-14
Black
MEDIA-BLACK-14
Cobalt (Blue)
MEDIA-COBALT-14
Touch Up Paint
Conversion Kit, NG
386-122A/2
TUP-GBK-12
6000CMOD-IPI
8000CMOD-IPI
N/A
LPKI-6CM
Y
N/A
LPKI-8CM
Y
Pilot Orifice, NG
593-528
Y
Pilot Orifice, LP
593-527
Y
Regulator, NG
NGK-DXV-50
Y
Regulator, LP
LPK-DXV-50
Y
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.
2000-945
Printed in U.S.A. - Copyright 2012
Heat & Glo • 6000CMOD-IPI, 8000CMOD-IPI • 2241-900 Rev. H • 5/12
71