Chamberlain 985 Garage Door Opener User Manual

®
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.chamberlain.com
GARAGE DOOR OPENER
Model 995XD 1/2 HP
For Residential Use Only
Owner’s Manual
■
Please read this manual and the enclosed safety materials carefully!
■
Fasten the manual near the garage door after installation.
■
The door WILL NOT CLOSE unless the Protector System® is connected and
properly aligned.
■
Periodic checks of the opener are required to ensure safe operation.
■
The model number label is located on the front panel of your opener.
TABLE OF CONTENTS
Introduction
2-7
Adjustment
Safety symbol and signal word review . . . . . . . . . . . . . . .2
Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . .3
Tools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Carton inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Hardware inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Assembly
Adjust the up and down travel limits . . . . . . . . . . . . . . .27
Adjust the force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Test the safety reversal system . . . . . . . . . . . . . . . . . . .29
Test the Protector System® . . . . . . . . . . . . . . . . . . . . . .29
Operation
30-34
Operation safety instructions . . . . . . . . . . . . . . . . . . . . .30
Using your garage door opener . . . . . . . . . . . . . . . . . . .30
Using the wall-mounted door control . . . . . . . . . . . . . . .31
To open the door manually . . . . . . . . . . . . . . . . . . . . . .31
Care of your garage door opener . . . . . . . . . . . . . . . . .32
Having a problem? . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Diagnostic chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
8-11
Assemble the rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Fasten the rail to the motor unit and
install the trolley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Attach the rail brackets . . . . . . . . . . . . . . . . . . . . . . . . . .11
Installation
27-29
11-26
Installation safety instructions . . . . . . . . . . . . . . . . . . . .11
Determine the header bracket location . . . . . . . . . . . . .12
Install the header bracket . . . . . . . . . . . . . . . . . . . . . . . .13
Attach the rail to the header bracket . . . . . . . . . . . . . . .14
Install the Protector System® . . . . . . . . . . . . . . . . . .15-17
Position the opener . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Hang the opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Install the door control . . . . . . . . . . . . . . . . . . . . . . . . . .20
Install the lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Attach the emergency release rope and handle . . . . . .21
Electrical requirements . . . . . . . . . . . . . . . . . . . . . . . . . .22
Complete safety reversing sensor installation . . . . . . . .22
Fasten the door bracket . . . . . . . . . . . . . . . . . . . . . .23-24
Connect the door arm to the trolley . . . . . . . . . . . . .25-26
Programming
35-36
To add or reprogram a hand-held remote control . . . . .35
To erase all codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
3-Button remotes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
To add, reprogram or change a Keyless Entry PIN . . . .36
Repair Parts
37-38
Rail assembly parts . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Installation parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Motor unit assembly parts . . . . . . . . . . . . . . . . . . . . . . .38
Accessories
39
Repair Parts and Service
40
Warranty
40
INTRODUCTION
Safety Symbol and Signal Word Review
This garage door opener has been designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the instructions and warnings contained in this manual.
When you see these Safety Symbols and Signal Words
on the following pages, they will alert you to the
possibility of serious injury or death if you do not
comply with the warnings that accompany them. The
hazard may come from something mechanical or from
electric shock. Read the warnings carefully.
WARNING
WARNING
Mechanical
CAUTION
WARNING
WARNING
Electrical
WARNING
CAUTION
WARNING
WARNING
When you see this Signal Word on the following pages, it
will alert you to the possibility of damage to your garage
door and/or the garage door opener if you do not comply
with the cautionary statements that accompany it. Read
them carefully.
WARNING
2
Preparing your garage door
WARNING
Before you begin:
• Disable locks.
• Remove any ropes connected to garage door.
• Complete the following test to make sure your
garage door is balanced and is not sticking or binding:
1. Lift the door about halfway as shown. Release the
door. If balanced, it should stay in place, supported
entirely by its springs.
2. Raise and lower the door to see if there is any
binding or sticking.
If your door binds, sticks, or is out of balance, call a
trained door systems technician.
To prevent possible SERIOUS INJURY or DEATH:
• ALWAYS call a trained door systems technician if garage
door binds, sticks, or is out of balance. An unbalanced
garage door may not reverse when required.
• NEVER try to loosen, move or adjust garage door, door
springs, cables, pulleys, brackets or their hardware, all of
which are under EXTREME tension.
• Disable ALL locks and remove ALL ropes connected to
garage door BEFORE installing and operating garage door
opener to avoid entanglement.
CAUTION
WARNING
CAUTION
To prevent damage to garage door and opener:
• ALWAYS disable locks BEFORE installing and operating the
opener.
• ONLY operate garage door opener at 120V, 60 Hz to avoid
malfunction and damage.
Sectional Door
Tools needed
One-Piece Door
During assembly, installation and adjustment of the
opener, instructions will call for hand tools as illustrated
below.
Pencil
Carpenter's
Level (Optional)
1
2
Hack Saw
Tape Measure
Wire Cutters
Drill
Stepladder
Claw Hammer
3/16", 5/16" and
5/32" Drill Bits
1/2" and 3/8" Sockets
and Wrench
Pliers
Screwdriver
3
Adjustable End Wrench
Planning
Identify the type and height of your garage door. Survey
your garage area to see if any of the conditions below
apply to your installation. Additional materials may be
required. You may find it helpful to refer back to this page
and the accompanying illustrations as you proceed with
the installation of your opener.
Depending on your requirements, there are several
installation steps which may call for materials or
hardware not included in the carton.
• Installation Step 1 – Look at the wall or ceiling above
the garage door. The header bracket must be securely
fastened to structural supports.
• Installation Step 4 – Depending upon garage
construction, extension brackets or wood blocks may
be needed to install sensors.
• Installation Step 4 – Alternate floor mounting of the
safety reversing sensor will require hardware not
provided.
• Installation Step 6 – Do you have a finished ceiling in
your garage? If so, a support bracket and additional
fastening hardware may be required.
• Do you have an access door in addition to the garage
door? If not, Model 7702CB Emergency Key Release
is required. See Accessories page.
• Look at the garage door where it meets the floor. Any
gap between the floor and the bottom of the door must
not exceed 1/4" (6 mm). Otherwise, the safety reversal
system may not work properly. See Adjustment Step 3.
Floor or door should be repaired.
SECTIONAL DOOR INSTALLATIONS
• Do you have a steel, aluminum, fiberglass or glass
panel door? If so, horizontal and vertical reinforcement
is required (Installation Step 12).
• The opener should be installed above the center of the
door. If there is a torsion spring or center bearing plate
in the way of the header bracket, it may be installed
within 4 feet (1.2 m) to the left or right of the door
center. See Installation Steps 1 and 12.
SECTIONAL DOOR INSTALLATION
FINISHED CEILING
Support bracket &
fastening hardware
is required.
See page 19.
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with
glass panels, etc.). See page 23 for details.
Rail
Header Wall
Motor unit
Torsion
Spring
Extension
OR Spring
Wallmounted
Door
Access Door
Control
CLOSED POSITION
Header
Bracket
———
Vertical
Centerline
of Garage
Door
Garage
Door
Spring
———
Straight
Door
Arm
——
Safety Reversing Sensor
Rail Assembly
Rail Bracket
Safety Reversing
Sensor
Gap between floor
and bottom of door
must not exceed 1/4" (6 mm).
Header
Wall
Garage
Door
4
Curved
Door
Door
Arm
Bracket
Trolley
Emergency
Release
Rope & Handle
Planning (Continued)
WARNING
ONE-PIECE DOOR INSTALLATIONS
• Generally, a one-piece door does not require
reinforcement. If your door is lightweight, refer to the
information relating to sectional doors in Installation
Step 12.
• Depending on your door’s construction, you may need
additional mounting hardware for the door bracket
(Step 12).
Without a properly working safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED
or KILLED by a closing garage door.
• The gap between the bottom of the garage door and the
floor MUST NOT exceed 1/4" (6 mm). Otherwise, the safety
reversal system may not work properly.
• The floor or the garage door MUST be repaired to eliminate
the gap.
CAUTION
ONE-PIECE DOOR WITHOUT TRACK
FINISHED CEILING
Support bracket
& fastening
hardware is required.
See page 19.
Rail
Header Wall
Motor unit
Wall-mounted
Door Control
Access
Door
Rail
Bracket
CLOSED POSITION
Rail Assembly
Header
Bracket
Door
Door Arm
Bracket
Safety Reversing
Sensor
Gap between floor
and bottom of door must not exceed 1/4" (6 mm).
Safety Reversing Sensor
Straight
Door
Arm
Garage
Door
Header
Wall
Trolley
Curved
Door
Arm
Emergency
Release
Rope & Handle
ONE-PIECE DOOR WITH TRACK
CLOSED POSITION
Access
Door
Header
Wall
Rail Bracket
Header
Bracket
Garage
Door
Safety
Reversing Sensor
Safety
Reversing Sensor
Gap between floor
and bottom of door
must not exceed 1/4" (6 mm).
5
Door
Bracket
Curved
Door Arm
Straight
Door
Arm
Trolley
Rail Assembly
Emergency Release
Rope & Handle
Carton Inventory
Your garage door opener is packaged in one carton which
contains the motor unit and all parts illustrated below.
Accessories will depend on the model purchased. If
anything is missing, carefully check the packing material.
PARTS MAY BE STUCK IN THE FOAM. Hardware for
assembly and installation is shown on the next page.
Save the carton and packing material until installation and
adjustment is complete.
Rail Support
Braces (4)
LOCK
Remote Control
Visor Clip
®
SECURITY
Keyless Entry
LIGHT
Multi-Function
Door Control Panel
SECURITY✚®
3-Button Remote Control
Sprocket
Coupling
Motor Unit with 2 Light Lenses
2-Conductor Bell Wire
White & White/Red
Rail Assembly
Trolley
Straight Door
Arm Section
Header/Rail
Brackets
G
ILIN
CE
T
UN
MO
LY
ON
UP
Curved Door
Arm Section
Header Bracket
Door Bracket
Hanging Brackets
Safety Labels
and
Literature
The Protector System®
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with attached 2-Conductor
White & White/Black Bell Wire
Safety Reversing Sensor
Mounting Bracket (2)
6
Hardware Inventory
Separate all hardware and group as shown below for the assembly and installation procedures.
ASSEMBLY HARDWARE
Sleeve (2)
Clip (2)
Hex bolt 1/4-20x7/16" (14)
Sprocket Coupling Sleeve
Wire Clips (6)
INSTALLATION HARDWARE
Carriage Bolt
1/4"-20x1/2" (2)
Wing Nut
1/4"-20 (2)
Lag Screw
5/16"-9x1-5/8" (2)
Ring
Fastener (3)
Handle
Nut 5/16"-18 (6)
Hex Bolt
5/16"-18x7/8" (4)
Lag Screw
5/16"-18x1-7/8" (2)
Lock Washer 5/16" (6)
Screw
6ABx1-1/4" (2)
Insulated
Staples (30)
Screw 6-32x1" (2)
Rope
Self-Threading Screw
1/4"-14x5/8"
Drywall Anchors (2)
Clevis Pin
5/16"x1" (1)
Clevis Pin
5/16"x2-3/4" (1)
7
Spacer
Clevis Pin
5/16"x1-1/4" (1)
WARNING
CAUTION
ASSEMBLY STEP 1
Assemble the Rail
To prevent INJURY from pinching, keep hands and fingers
away from the joints while assembling the rail.
To avoid installation difficulties, do not run the
garage door opener until instructed to do so.
1. Open the rail carton and remove the contents onto a
level work surface. Keep it clean and free of debris
while you are working.
2. Identify the rail sections and orient the sections on a
flat surface as shown. The back rail has a black gear
on one end. The header rail has a black plastic rack
inside the rail on the screw. The remaining section is
the center rail.
NOTE: Use caution when handling the center rail
section. The screw can slip out if the section is tipped up
too far.
HARDWARE SHOWN ACTUAL SIZE
Hex Bolt 1/4-20x7/16"
Remove Cardboard Packing
Hanging Brackets
Rail Support Braces
Rail Assembly
Straight Door Arm
Header Rail Brackets
Rail Assembly
Remove Cardboard Packing
Sprocket Coupling
Remove
Cardboard
Packing
Rail Assembly Carton
Hex Bolts
1/4-20x7/16"
Back Rail
Hex Bolts
1/4-20x7/16"
Hex Bolts
1/4-20x7/16"
Center Rail
Hex Bolts
1/4-20x7/16"
8
Header Rail
Assemble the Rail (continued)
3. Attach rail support braces to the back rail. Loosely
insert 1/4-20x7/16" hex bolts into the aligned holes of
the end rail and rail support brace (Figure 1). Do not
finger tighten.
4. Extend the drive screw a few inches from the center
rail, and slide the sleeve onto the long journal
(Figure 2).
HARDWARE SHOWN ACTUAL SIZE
Sleeve
Hex Bolt 1/4-20x7/16"
Clip
5. Interlock the long and short journal of the center and
back rails. Slide the sleeve over the journal connection
(Figure 3).
6. Place the c-clip onto the long journal shaft (center rail)
to ensure that the sleeve does not slide (Figure 4).
7. Slide the center rail so that the center rail and rail
brace holes are aligned (Figure 5). Secure with bolts.
8. Tighten all hex bolts.
9. Repeat steps 3-8 for header section.
Figure 4
Figure 1
Metal Sleeve
Rail
Rail Support Brace
C-Clip
Center Rail
Rail Support Brace
Figure 2
Figure 5
Drive Screw
Metal Sleeve
Long Journal
Rail Support Brace
Center Rail
Center Rail
Figure 3
Short Journal
Metal Sleeve
Long Journal
Rail Support Brace
9
ASSEMBLY STEP 2
HARDWARE SHOWN ACTUAL SIZE
Fasten the Rail to the Motor Unit and
Install the Trolley
NOTE: To aid in assembly and installation, replace the
foam packing around the motor unit. Remove it after
Installation Step 4.
1. Working on a level surface, align the rail assembly with
the motor unit, as shown.
2. Slip the coupling over the rail sprocket.
3. Slide the rail through the motor unit bracket until the
coupling fits securely over the motor unit sprocket.
4. Align the four bolt holes in the rail with those in the
motor unit bracket. Insert four 1/4"-20x7/16" hex bolts.
Tighten securely with a 3/8" socket wrench.
5. Disengage trolley by turning the release arm down
(arrow pointing up). Slide trolley onto and along the
bottom of the rail until it aligns with the rack. Turn
release arm up (arrow pointing away from motor unit.
This will join the rack and the trolley.
Hex Bolt 1/4-20x7/16"
Motor Unit
Motor Unit
Bracket
Sprocket
Hex Bolts
1/4-20x7/16"
Coupling
Rail
Sprocket
Hex Bolts
1/4-20x7/16"
Rail
Assembly
Foam Packaging
Arrow must point up
Release arm
Rack
Trolley
To the motor unit
10
Rail Brackets
ASSEMBLY STEP 3
Attach the Rail Brackets
• Align rail brackets to end of rail assembly, as shown.
• Insert two 1/4"-20x7/16" hex bolts. Tighten securely
with a 3/8" socket.
You have now finished assembling your garage door
opener. Please read the following warnings before
proceeding to the installation section.
Hex Bolt
1/4-20 x 7/16"
Rail
Hex Bolt
1/4-20x7/16"
HARDWARE SHOWN ACTUAL SIZE
WARNING
Hex Bolt 1/4-20x7/16"
WARNING
INSTALLATION
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL INSTALLATION WARNINGS
AND INSTRUCTIONS.
2. Install garage door opener only on properly balanced
and lubricated garage door. An improperly balanced
door may not reverse when required and could result in
SEVERE INJURY or DEATH.
3. ALL repairs to cables, spring assemblies and other
hardware MUST be made by a trained door systems
technician BEFORE installing opener.
4. Disable ALL locks and remove all ropes connected to
garage door BEFORE installing opener to avoid
entanglement.
5. Install garage door opener 7 feet (2.13 m) or more
above floor.
6. Mount emergency release handle 6 feet (1.83 m) above
floor.
7. NEVER connect garage door opener to power source
until instructed to do so.
8. NEVER wear watches, rings or loose clothing while
installing or servicing opener. They could be caught in
garage door or opener mechanisms.
9. Install wall-mounted garage door control:
• within sight of the garage door.
• out of reach of children at minimum height of 5 feet
(1.5 m).
• away from ALL moving parts of the door.
10. Place entrapment warning label on wall next to garage
door control.
11. Place manual release/safety reverse test label in plain
view on inside of garage door.
12. Upon completion of installation, test safety reversal
system. Door MUST reverse on contact with a
1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on
the floor.
11
INSTALLATION STEP 1
Unfinished
Ceiling
OPTIONAL
CEILING
MOUNT
FOR
HEADER
BRACKET
Determine the Header Bracket
Location
WARNING
WARNING
2x4
Header Wall
Vertical Centerline
of Garage Door
To prevent possible SERIOUS INJURY or DEATH:
• Header bracket MUST be RIGIDLY fastened to structural
support on header wall or ceiling, otherwise garage door
might not reverse when required. DO NOT install header
bracket over drywall.
• Concrete anchors MUST be used if mounting header
bracket or 2x4 into masonry.
• NEVER try to loosen, move or adjust garage door, springs,
cables, pulleys, brackets, or their hardware, all of which are
under EXTREME tension.
• ALWAYS call a trained door systems technician if garage
door binds, sticks, or is out of balance. An unbalanced
garage door might not reverse when required.
CAUTION
Installation procedures vary according to garage door
types. Follow the instructions which apply to your door.
1. Close the door and mark the inside vertical centerline
of the garage door.
2. Extend the line onto the header wall above the door.
You can fasten the header bracket within 4 feet
(1.22 m) of the left or right of the door center only
if a torsion spring or center bearing plate is in the
way; or you can attach it to the ceiling (see
page 13) when clearance is minimal. (It may be
mounted on the wall upside down if necessary, to
gain approximately 1/2" (1 cm).)
If you need to install the header bracket on a 2x4
(on wall or ceiling), use lag screws (not provided)
to securely fasten the 2x4 to structural supports as
shown here and on page 13.
3. Open your door to the highest point of travel as shown.
Draw an intersecting horizontal line on the header wall
above the high point:
• 3" (7.5 cm) above the high point for sectional door
and one-piece door with track.
• 8" (20 cm) above the high point for one-piece door
without track.
This height will provide travel clearance for the top
edge of the door.
NOTE: If the total number of inches exceeds the
height available in your garage, use the maximum
height possible, or refer to page 13 for ceiling
installation.
2x4
WARNING
Structural
Supports
Level
(optional)
Header Wall
3" (7.5 cm) Track
Header Wall
3" (7.5 cm)
Highest Point
of Travel
Track
Highest Point
of Travel
Door
Door
Sectional door with curved track
One-piece door with horizontal track
Header Wall
Header Wall
8" (20 cm)
8" (20 cm)
Door
Highest
Point
of Travel
Highest
Point
of Travel
Door
Jamb
Hardware
Pivot
One-piece door without track:
jamb hardware
12
One-piece door without track:
pivot hardware
INSTALLATION STEP 2
Install the Header Bracket
Wall Mounting Holes
You can attach the header bracket either to the wall
above the garage door, or to the ceiling. Follow the
instructions which will work best for your particular
requirements. Do not install the header bracket over
drywall. If installing into masonry, use concrete
anchors (not provided).
CEILING MOUNT ONLY
The nail hole is for
positioning only.
You must use lag screws
to mount the header bracket.
UP
Optional
Wall Mounting Holes
WALL HEADER BRACKET INSTALLATION
• Center the bracket on the vertical centerline with the
bottom edge of the bracket on the horizontal line as
shown (with the arrow pointing toward the ceiling).
• Mark the vertical set of bracket holes. Drill 3/16" pilot
holes and fasten the bracket securely to a structural
support with the hardware provided.
Vertical
Centerline of
Garage Door
Header
Wall
G
ILIN
CE
Lag Screws
5/16"-9x1-5/8"
NLY
TO
UN
MO
UP
2x4
Structural
Support
Header
Bracket
Door Spring
HARDWARE SHOWN ACTUAL SIZE
Horizontal
Line
Garage
Door
Highest Point of
Garage Door Travel
Vertical
Centerline of
Garage Door
Lag Screw
5/16"-9x1-5/8"
CEILING HEADER BRACKET INSTALLATION
• Extend the vertical centerline onto the ceiling as shown.
• Center the bracket on the vertical mark, no more than
6" (15 cm) from the wall. Make sure the arrow is
pointing toward the wall. The bracket can be mounted
flush against the ceiling when clearance is minimal.
• Mark the side holes. Drill 3/16" pilot holes and fasten
bracket securely to a structural support with the
hardware provided.
– Finished Ceiling –
Header
Bracket
Door
Spring
Ceiling Mounting Holes
UP
6" (15 cm)
Maximum
Vertical
Centerline
of Garage Door
Lag Screws
5/16"-9x1-5/8"
CEILING MOUNT ONLY
UP
Header Wall
The nail hole is for
positioning only.
You must use lag screws
to mount the header bracket.
Garage Door
13
Vertical
Centerline
of Garage Door
INSTALLATION STEP 3
Attach the Rail to the Header Bracket
• Position the opener on the garage floor below the
header bracket. Use packing material as a protective
base. NOTE: If the door spring is in the way you’ll
need help. Have someone hold the opener securely on
a temporary support to allow the rail to clear the
spring.
• Position the header/rail bracket against the header
bracket.
• Align the bracket holes and join with a clevis pin
5/16"x2-3/4" as shown. Spacer can be installed on
either side of rail.
• Insert a ring fastener to secure.
Header Wall
Header Bracket
Header/Rail Bracket
Ring Fastener
Header Bracket
Rail
Clevis Pin
5/16"x2-3/4"
Spacer
Header/Rail
Bracket
Rail
Garage
Door
Opener Carton or
Temporary
Support
HARDWARE SHOWN ACTUAL SIZE
Clevis Pin
5/16"x2-3/4"
Ring Fastener
14
Spacer
WARNING
INSTALLATION STEP 4
Install The Protector System
®
Be sure power is not connected to the garage door opener
BEFORE installing the safety reversing sensor.
To prevent SERIOUS INJURY or DEATH from a closing
garage door:
• Correctly connect and align the safety reversing sensor.
This required safety device MUST NOT be disabled.
• Install the safety reversing sensor so beam is NO HIGHER
than 6" (15 cm) above garage floor.
CAUTION
The safety reversing sensor must be connected and
aligned correctly before the garage door opener will
move in the down direction.
IMPORTANT INFORMATION ABOUT
THE SAFETY REVERSING SENSOR
When properly connected and aligned, the sensor will
detect an obstacle in the path of its electronic beam. The
sending eye (with an amber indicator light) transmits an
invisible light beam to the receiving eye (with a green
indicator light). If an obstruction breaks the light beam
while the door is closing, the door will stop and reverse
to full open position, and the opener lights will flash
10 times.
The units must be installed inside the garage so that the
sending and receiving eyes face each other across the
door, no more than 6" (15 cm) above the floor. Either can
be installed on the left or right of the door as long as the
sun never shines directly into the receiving eye lens.
The mounting brackets are designed to clip onto the
track of sectional garage doors without additional
hardware.
Safety Reversing Sensor
6" (15 cm) max. above floor
If it is necessary to mount the units on the wall, the
brackets must be securely fastened to a solid surface
such as the wall framing. Extension brackets (see
accessories) are available if needed. If installing in
masonry construction, add a piece of wood at each
location to avoid drilling extra holes in masonry if
repositioning is necessary.
The invisible light beam path must be unobstructed. No
part of the garage door (or door tracks, springs, hinges,
rollers or other hardware) may interrupt the beam while
the door is closing.
Invisible Light Beam
Protection Area
Facing the door from inside the garage
15
Safety Reversing Sensor
6" (15 cm) max. above floor
INSTALLING THE BRACKETS
Be sure power to the opener is disconnected. Install
and align the brackets so the sensors will face each
other across the garage door, with the beam no higher
than 6" (15 cm) above the floor. They may be installed in
one of three ways, as follows.
Figure 1
DOOR TRACK MOUNT (RIGHT SIDE)
Door
Track
Lip
Garage door track installation (preferred):
• Slip the curved arms over the rounded edge of each
door track, with the curved arms facing the door. Snap
into place against the side of the track. It should lie
flush, with the lip hugging the back edge of the track,
as shown in Figure 1.
If your door track will not support the bracket securely,
wall installation is recommended.
Indicator
Light
Sensor
Bracket
Wall installation (Figure 2 & 3):
• Place the bracket against the wall with curved arms
facing the door. Be sure there is enough clearance for
the sensor beam to be unobstructed.
• If additional depth is needed, an extension bracket
(See Accessories) or wood blocks can be used.
• Use bracket mounting holes as a template to locate
and drill (2) 3/16" diameter pilot holes on the wall at
each side of the door, no higher than 6" (15 cm) above
the floor.
• Attach brackets to wall with lag screws (Not provided).
• If using extension brackets or wood blocks, adjust right
and left assemblies to the same distance out from the
mounting surface. Make sure all door hardware
obstructions are cleared.
Lens
ide
Ins age
r
a
G l
l
Wa
Figure 2
WALL MOUNT (RIGHT SIDE)
Fasten Wood Block to Wall with
Lag Screws (Not Provided)
Indicator
Light
Sensor
Bracket
Lag Screws
(Not Provided)
Lens
Figure 3
WALL MOUNT (RIGHT SIDE)
ide
Ins age
r
Ga l
l
Wa
Floor installation (Figure 4):
• Use wood blocks or extension brackets (See
Accessories) to elevate sensor brackets so the lenses
will be no higher than 6" (15 cm) above the floor.
• Carefully measure and place right and left assemblies
at the same distance out from the wall. Be sure all
door hardware obstructions are cleared.
• Fasten to the floor with concrete anchors as shown.
Extension
Bracket
(See Accessories)
(Provided with
Extension Bracket)
Sensor
Bracket
(Provided with
Extension
Bracket)
Lens
Figure 4
Indicator
Light
FLOOR MOUNT (RIGHT SIDE)
HARDWARE SHOWN ACTUAL SIZE
Attach with
Concrete Anchors
(Not Provided)
ide
Ins rage
a
G ll
Wa
Lens
Carriage Bolt
1/4"-20x1/2"
Wing Nut
1/4"-20
Indicator
Light
Staples
Sensor
Bracket
16
MOUNTING AND WIRING THE SAFETY SENSORS
• Slide a 1/4"-20x1/2" carriage bolt head into the slot on
each sensor. Use wing nuts to fasten sensors to
brackets, with lenses pointing toward each other
across the door. Be sure the lens is not obstructed by
a bracket extension. See Figure 5.
• Finger tighten the wing nuts.
Figure 5
Wing Nut
1/4"-20
Carriage Bolt
1/4"-20x1/2"
Recommended Wire Routing
1. Using insulated staples, run the wires from both
sensors to the rail at the door header (see Figure 6).
2. Run the wires through wire clip at the top of the rails.
NOTE: If your access door is near the garage door,
you may choose to install the door control at this time
and run the door control wire along the rail with the
sensor wires. If you choose this option, follow
instructions 1-3 on page 20.
Lens
HARDWARE SHOWN ACTUAL SIZE
Carriage Bolt
1/4"-20x1/2"
Wing Nut
1/4"-20
Figure 6
Sensor Wire
Wire Clip
Bell Wire
Rail
Safety Reversing
Sensor
17
Invisible Light Beam
Protection Area
Safety Reversing
Sensor
Staples
Wire Clip
WARNING
CAUTION
INSTALLATION STEP 5
Position the Opener
To prevent damage to garage door, rest garage door opener
rail on 2x4 placed on top section of door.
Follow instructions which apply to your door type as
illustrated.
SECTIONAL DOOR OR ONE-PIECE DOOR WITH
TRACK
A 2x4 laid flat is convenient for setting an ideal door-torail distance.
• Remove foam packaging.
• Raise the opener onto a stepladder. You will need help
at this point if the ladder is not tall enough.
• Open the door all the way and place a 2x4 laid flat on
the top section beneath the rail.
• If the top section or panel hits the trolley when you
raise the door, pull down on the trolley release arm
to disconnect inner and outer sections. Slide the outer
trolley toward the motor unit. The trolley can remain
disconnected until Installation Step 13 is completed.
Top of Door
2x4 is used to determine
the correct mounting height
from ceiling.
Door
Trolley
Release Arm
ENGAGED
RELEASED
ONE-PIECE DOOR WITHOUT TRACK
A 2x4 on its side is convenient for setting an ideal doorto-rail distance.
• Remove foam packaging.
• Raise the opener onto a stepladder. You will need help
at this point if the ladder is not tall enough.
• Open the door all the way and place a 2x4 on its side
on the top section of the door beneath the rail.
• The top of the door should be level with the top of the
motor unit. Do not position the opener more than 4"
(10 cm) above this point.
Top of Door
2x4 is used to determine
the correct mounting height
from ceiling.
18
WARNING
INSTALLATION STEP 6
Hang the Opener
To avoid possible SERIOUS INJURY from a falling garage
door opener, fasten it SECURELY to structural supports of
the garage. Concrete anchors MUST be used if installing ANY
brackets into masonry.
CAUTION
Three representative installations are shown. Yours may
be different. Hanging brackets should be angled
(Figure 1) to provide rigid support. On finished ceilings
(Figure 2), attach a sturdy metal bracket to structural
supports before installing the opener. This bracket and
fastening hardware are not provided (see accessories).
Existing brackets from a previous installation may be
fastened to the sides of the motor unit as in Figures 1
and 2, or to the mounting tabs as shown in Figure 3.
Then continue with step 6 below.
Figure 1
Structural
Supports
Measure
Distance
Lag Screws
5/16"-18x1-7/8"
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
1. Measure the distance from each side of the motor unit
to the structural support.
2. Cut both pieces of the hanging bracket to required
lengths.
3. Drill 3/16" pilot holes in the structural supports.
4. Attach one end of each bracket to a support with
5/16"-18x1-7/8" lag screws.
5. Fasten the opener to the hanging brackets with
5/16"-18x7/8" hex bolts, lock washers and nuts.
6. Check to make sure the rail is centered over the door
(or in line with the header bracket if the bracket is not
centered above the door).
7. Remove the 2x4. Operate the door manually. If the
door hits the rail, raise the header bracket.
NOTE: DO NOT connect power to opener at this time.
Figure 2
Bracket
(Not Provided)
Hidden
Support
FINISHED CEILING
Lag Screws
5/16"-18x1-7/8"
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
(Not Provided)
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
HARDWARE SHOWN ACTUAL SIZE
Figure 3
Lag Screws
5/16"-18x1-7/8"
Lag Screw 5/16"-18x1-7/8"
FINISHED CEILING
Hex Bolt
5/16"-18x7/8"
Nut 5/16"-18
Lock Washer 5/16"
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
19
(Not Provided)
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
WARNING
WARNING
INSTALLATION
CAUTIONSTEP 7
WARNING
Install the Door Control
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door
control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.52 m), and
away from all moving parts of door.
• NEVER permit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVER permit anyone to cross path of closing garage door.
Locate door control within sight of door at a minimum
height of 5 feet (1.5 m) where small children cannot reach,
and away from moving parts of door and door hardware.
The installation surface must be smooth and flat. If
installing into drywall (Figure 1), drill 5/32" holes and use
anchors provided. For pre-wired installations (as in new
home construction), it may be mounted to a single gang
box (Figure 2). NOTE: After installation, a green or amber
indicator light behind the cover will indicate proper
connection. If not lit, the Lock and Light features will not
function (reverse wires to correct).
1. Strip 7/16" (11 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back of
door control by color: white wire to WHT and white/red
wire to the RED (Figure 3).
2. Remove cover by gently prying on a side corner near
the top of the cover with a small flat head screwdriver
(Figure 4). Fasten with 6ABx1-1/4" self-tapping screws
(drywall installation) or 6-32x1" machine screws (into
gang box) as follows:
• Drill and install bottom screw, allowing 1/8" (3 mm) to
protrude above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Install top screw with care to avoid cracking plastic
housing. Do not overtighten.
• Insert bottom tabs and snap on cover.
NOTE: The push bar may stick if the door control is not
mounted on a smooth surface. If a click is not heard
when pressing the push bar, loosen the two mounting
screws or relocate the door control to a smoother
surface.
3. (Standard installation only) Run bell wire up wall and
across ceiling to motor unit. Use insulated staples to
secure wire in several places. Do not pierce wire with a
staple, creating a short or open circuit. If your access
door is near the garage door, you may run this wire with
the Safety Reversing Sensor wires along the top of the
rail. See page 17.
4. Insert all wires through the opening on top of motor unit
above the terminal block on the back panel (Figure 4).
5. Strip 7/16" (11 mm) of insulation from each set of bell
wires. Connect bell wires to the quick-connect terminals
as follows: white to white and white/red to red; white to
white and white/black to grey.
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires into
quick-connect holes: white to white and red/white to red.
6. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location
on inside of garage door.
NOTE: DO NOT connect the power and operate the opener
at this time. The trolley will travel to the full open position but
will not return to the close position until the sensor beam is
connected and properly aligned.
HARDWARE SHOWN ACTUAL SIZE
Insulated
Staples
Screw 6ABx1-1/4"
Control Panel (std installation)
Screw 6-32x1"
Control Panel (pre-wired)
Figure 1
Drywall Anchors
STANDARD
INSTALLATION
Figure 2
PRE-WIRED
INSTALLATION
LOCK
LIGHT
LOCK
LIGHT
To Replace
Insert Bottom Tabs First
24 Volt
Bell Wire
To Replace
Insert Bottom Tabs First
Figure 3
Figure 4
MULTI-FUNCTION
WALL CONTROL PANEL
Terminal
Screws
Bell
Wire
9
1
3
5
KG
2
Bottom
Mounting Hole
To release wire, push in
tab with screwdriver tip
Door Control
Connections
Safety Sensor
Connections
Red White Grey
7/16" (11 mm)
Strip wire 7/16" (11 mm)
20
1
7
RED WHT
9
1
7
3
5
KG
WARNING
CAUTION
INSTALLATION STEP 8
Install the Lights
To prevent possible OVERHEATING of the endpanel or light
socket:
• DO NOT use short neck or specialty light bulbs.
• DO NOT use halogen bulbs. Use ONLY incandescent.
To prevent damage to the opener:
• DO NOT use bulbs larger than 100W.
• ONLY use A19 size bulbs.
• Press the release tabs on both sides of lens. Gently
rotate lens back and downward until the lens hinge is
in the fully open position. Do not remove the lens.
• Install a 100 watt maximum light bulb in each socket.
Light bulb size should be A19, standard neck only. The
lights will turn ON and remain lit for approximately
4-1/2 minutes when power is connected. Then the
lights will turn OFF.
• Reverse the procedure to close the lens.
• Use A19, standard neck garage door opener bulbs for
replacement.
NOTE: Use only standard light bulbs. The use of short
neck or speciality light bulbs may overheat the endpanel
or light socket.
100 Watt (Max)
Standard Light Bulb
Release Tab
Lens
Hinge
100 Watt (Max)
Standard Light Bulb
INSTALLATION STEP 9
WARNING
Attach the Emergency Release Rope
and Handle
To prevent possible SERIOUS INJURY or DEATH from a
falling garage door:
• If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope knot
becomes untied, you could fall.
CAUTION
• Thread one end of the rope through the hole in the top
of the red handle so “NOTICE” reads right side up as
shown. Secure with an overhand knot at least
1" (2.5 cm) from the end of the rope to prevent
slipping.
• Thread the other end of the rope through the hole in
the release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet (1.83 m)
above the floor. Ensure that the rope and handle clear
the tops of all vehicles to avoid entanglement. Secure
with an overhand knot.
NOTE: If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
Trolley
Trolley Release Arm
Emergency
Release Handle
21
NOT
ICE
Overhand
Knot
INSTALLATION
WARNINGSTEP 10
WARNING
Electrical Requirements
To prevent possible SERIOUS INJURY or DEATH from
electrocution or fire:
• Be sure power is not connected to the opener, and
disconnect power to circuit BEFORE removing cover to
establish permanent wiring connection.
• Garage door installation and wiring MUST be in compliance
with all local electrical and building codes.
• NEVER use an extension cord, 2-wire adapter, or change
plug in any way to make it fit outlet. Be sure the opener is
grounded.
CAUTION
WARNING
To avoid installation difficulties, do not run the
opener until Step 11 below.
To reduce the risk of electric shock, your garage door
opener has a grounding type plug with a third grounding
pin. This plug will only fit into a grounding type outlet. If
the plug doesn't fit into the outlet you have, contact a
qualified electrician to install the proper outlet.
RIGHT
PERMANENT WIRING
CONNECTION
WRONG
If permanent wiring is required by your local code,
refer to the following procedure.
To make a permanent connection through the 7/8" hole
in the top of the motor unit:
• Remove the motor unit cover screws and set the cover
aside.
• Remove the attached 3-prong cord.
• Connect the black (line) wire to the screw on the brass
terminal; the white (neutral) wire to the screw on the
silver terminal; and the ground wire to the green
ground screw. The opener must be grounded.
• Reinstall the cover.
To avoid installation difficulties, do not run the
opener until Step 11 below.
Ground Tab
Green
Ground Screw
Black
Wire
Ground Wire
White Wire
Black Wire
INSTALLATION STEP 11
Complete the Safety Reversing Sensor
Installation
TROUBLESHOOTING THE SAFETY
REVERSING SENSORS
1. If the sending eye indicator light does not glow steadily
after installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These can
occur at staples, or at opener connections.
• Incorrect wiring between sensors and opener.
• A broken wire.
2. If the sending eye indicator light glows steadily but the
receiving eye indicator light doesn’t:
• Check alignment.
• Check for an open wire to the receiving eye.
3. If the receiving eye indicator light is dim, realign either
sensor.
NOTE: When the invisible beam path is obstructed or
misaligned while the door is closing, the door will
reverse. If the door is already open, it will not close. The
opener lights will flash 10 times. (See page 15.)
ALIGNING THE SAFETY REVERSING SENSORS
• Plug in the opener. The indicator lights in both the
sending and receiving eyes will glow steadily if wiring
connections and alignment are correct.
The sending eye amber indicator light will glow
regardless of alignment or obstruction. If the green
indicator light in the receiving eye is off, dim, or flickering
(and the invisible light beam path is not obstructed),
alignment is required:
• Loosen the sending eye wing nut and readjust, aiming
directly at the receiving eye. Lock in place.
• Loosen the receiving eye wing nut and adjust the
sensor until it receives the sender’s beam. When the
green indicator light glows steadily, tighten the wing
nut.
22
WARNING
CAUTION
INSTALLATION STEP 12
Fasten the Door Bracket
Fiberglass, aluminum or lightweight steel garage doors WILL
REQUIRE reinforcement BEFORE installation of door bracket.
Contact your door manufacturer for reinforcement kit.
Follow instructions which apply to your door type
as illustrated below or on the following page.
A horizontal reinforcement brace should be long
enough to be secured to two or three vertical
supports. A vertical reinforcement brace should
cover the height of the top panel.
Figure 1 shows one piece of angle iron as the horizontal
brace. For the vertical brace, 2 pieces of angle iron are
used to create a U-shaped support. The best solution is
to check with your garage door manufacturer for an
opener installation door reinforcement kit.
NOTE: Many door reinforcement kits provide for direct
attachment of the clevis pin and door arm. In this case
you will not need the door bracket; proceed to Step 13.
Header
Bracket
Door
Bracket
Location
SECTIONAL DOORS
1. Center the door bracket on the previously marked
vertical centerline used for the header bracket
installation. Note correct UP placement, as stamped
inside the bracket.
2. Position the top edge of the bracket 2"-4" (5-10 cm)
below the top edge of the door, OR directly below any
structural support across the top of the door.
3. Mark, drill holes and install as follows, depending on
your door’s construction:
HORIZONTAL AND VERTICAL
REINFORCEMENT IS NEEDED
FOR LIGHTWEIGHT GARAGE
DOORS (FIBERGLASS,
ALUMINUM, STEEL, DOORS
WITH GLASS PANEL, ETC.).
(NOT PROVIDED)
Vertical
Centerline
of Garage
Door
Figure 1
(Not Provided)
Vertical
Reinforcement
Vertical
Reinforcement
Metal or light weight doors using a vertical angle iron
brace between the door panel support and the door
bracket:
• Drill 3/16" fastening holes. Secure the door bracket
using the two 1/4"-14x5/8" self-threading screws.
(Figure 2A)
• Alternately, use two 5/16" bolts, lock washers and nuts
(not provided). (Figure 2B)
Vertical
Centerline
of Garage Door
Vertical
Centerline
of Garage Door
Bolt
5/16"-18x2"
UP
UP
Lock Washer
5/16"
Nut
5/16"-18
Door
Bracket
Self-Threading
Screw
1/4"-14x5/8"
Metal, insulated or light weight factory reinforced
doors:
• Drill 3/16" fastening holes. Secure the door bracket
using the self-threading screws (Figure 3).
Door
Bracket
Figure 2B
Figure 2A
(Not Provided)
Wood Doors:
• Use top and bottom or side to side door bracket holes.
Drill 5/16" holes through the door and secure bracket
with 5/16"x2" carriage bolts, lock washers and nuts
(not provided). (Figure 4)
NOTE: The 1/4"-14x5/8" self-threading screws are not
intended for use on wood doors.
Inside Edge
of Door or
Reinforcement Board
Bolt
5/16"x2"
UP
Vertical
Centerline
of Garage Door
UP
HARDWARE
SHOWN
ACTUAL SIZE
Self-Threading
Screw
1/4"-14x5/8"
Self-Threading
Screw
1/4"-14x5/8"
Figure 3
23
Vertical
Centerline
of Garage
Door
Figure 4
ONE-PIECE DOORS
Please read and comply with the warnings and
reinforcement instructions on the previous page. They
apply to one-piece doors also.
• Center the door bracket on the top of the door, in line
with the header bracket as shown. Mark either the left
and right, or the top and bottom holes.
• Metal Doors: Drill 3/16" pilot holes and fasten the
bracket with the 1/4"-14x5/8" self-threading screws
provided.
• Wood Doors: Drill 5/16" holes and use 5/16"x2"
carriage bolts, lock washers and nuts (not provided) or
5/16"x1-1/2" lag screws (not provided) depending on
your installation needs.
HARDWARE SHOWN
ACTUAL SIZE
Self-Threading Screw
1/4"-14x5/8"
NOTE: The door bracket may be installed on the top
edge of the door if required for your installation. (Refer to
the dotted line optional placement drawing.)
Self-Threading
Screw
1/4"-14x5/8"
Header Wall
2x4 Support
Door
Bracket
Finished Ceiling
Top of Door
(Inside
Garage)
Top Edge
of Door
Header
Bracket
Optional
Placement
Door
Bracket
METAL DOOR
Optional
Placement
of Door
Bracket
Vertical
Centerline of
Garage Door
HORIZONTAL AND VERTICAL
REINFORCEMENT IS NEEDED
FOR LIGHTWEIGHT GARAGE
DOORS (FIBERGLASS,
ALUMINUM, STEEL, DOORS
WITH GLASS PANEL, ETC.).
(NOT PROVIDED)
Nut
5/16"-18
Door
Bracket
Lock
Washer
5/16"
Top of Door
(Inside
Garage)
Top Edge
of Door
Optional
Placement
Carriage Bolt
5/16"x2"
(Not Provided)
For a door with no exposed framing,
or for the optional installation, use
lag screws 5/16"x1-1/2" (Not Provided)
to fasten door bracket.
24
WOOD DOOR
INSTALLATION STEP 13
Connect Door Arm to Trolley
Inner
Trolley
Follow instructions which apply to your door type as
illustrated below and on the following page.
SECTIONAL DOORS ONLY
• Make sure garage door is fully closed. Pull the
emergency release handle to disconnect the outer
trolley from the inner trolley. Slide the outer trolley back
(away from the door) about 2" (5 cm) as shown in
Figures 1, 2 and 3.
• Figure 1:
– Fasten straight door arm section to outer trolley with
the 5/16"x1" clevis pin. Secure the connection with a
ring fastener.
– Fasten curved section to the door bracket in the
same way, using the 5/16"x1-1/4" clevis pin.
• Figure 2:
– Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
• Figure 3, Hole alignment alternative:
– If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 6" (15 cm)
from the solid end. Reconnect to trolley with cut end
down as shown.
– Bring arm sections together.
– Find two pairs of holes that line up and join with
bolts, lock washers and nuts.
• Pull the emergency release handle toward the opener
at a 45° angle so that the trolley release arm is
horizontal. Proceed to Adjustment Step 1, page 27.
Trolley will re-engage automatically when opener is
operated.
Outer
Trolley
Ring
Fastener
Clevis Pin
5/16"x1"
Straight
Door Arm
Emergency
Release
Handle
Door
Bracket
Curved Door Arm
Clevis Pin
5/16"x1-1/4"
Figure 1
Lock
Washers
5/16"
Nuts
5/16"-18
Bolts
5/16"-18x7/8"
Door Bracket
Figure 2
HARDWARE SHOWN ACTUAL SIZE
Nut 5/16"-18
Lock Washer 5/16"
Lock
Washers
5/16"
Ring Fastener
Nuts
5/16"-18
Clevis Pin
5/16"x1" (Trolley)
Clevis Pin
5/16"x1-1/4" (Door Bracket)
Hex Bolt
5/16"-18x7/8"
Bolts
5/16"-18x7/8"
Cut this end
Figure 3
25
ALL ONE-PIECE DOORS
1. Assemble the door arm, Figure 4:
• Fasten the straight and curved door arm sections
together to the longest possible length (with a 2 or 3
hole overlap).
• With the door closed, connect the straight door arm
section to the door bracket with the
5/16"x1-1/4" clevis pin.
• Secure with a ring fastener.
2. Adjustment procedures, Figure 5:
• On one-piece doors, before connecting the door arm
to the trolley, the travel limits must be adjusted. Limit
adjustment screws are located on the left side panel
as shown on page 27. Follow adjustment procedures
below.
• Open door adjustment: decrease UP travel limit
- Turn the UP limit adjustment screw
counter-clockwise 4 turns.
- Press the Door Control push button. The trolley will
travel to the fully open position.
- Manually raise the door to the open position (parallel
to the floor), and lift the door arm to the trolley. The
arm should touch the trolley just in back of the door
arm connector hole. Refer to the fully open
trolley/door arm positions in the illustration. If the
arm does not extend far enough, adjust the limit
further. One full turn equals 2" (5 cm) of trolley
travel.
• Closed door adjustment: decrease DOWN travel
limit
- Turn the DOWN limit adjustment screw clockwise
4 complete turns.
Door
Bracket
Ring
Fastener
Lock
Washers
5/16"
Clevis Pin
5/16"x1-1/4"
Figure 4
Straight
Arm
Bolts
5/16"-18x7/8"
Curved
Door Arm
- Press the Door Control push button. The trolley will
travel to the fully closed position.
- Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead of
the door arm connector hole. Refer to the fully
closed trolley/door arm positions in the illustration. If
the arm is behind the connector hole, adjust the limit
further. One full turn equals 2" (5 cm) of trolley travel.
3. Connect the door arm to the trolley:
• Close the door and join the curved arm to the
connector hole in the trolley with the remaining clevis
pin. It may be necessary to lift the door slightly to
make the connection.
• Secure with a ring fastener.
• Run the opener through a complete travel cycle. If the
door has a slight “backward” slant in full open position
as shown in the illustration, decrease the UP limit until
the door is parallel to the floor.
NOTE: When setting the up limit on the following page,
the door should not have a “backward” slant when fully
open as illustrated below. A slight backward slant will
cause unnecessary bucking and/or jerking operation as
the door is being opened or closed from the fully open
position.
Figure 5
Inner Trolley
Nuts
5/16"-18
Outer Trolley
Closed
Door
Door Arm
Connector Hole
Door Arm
Emergency
Release Handle
Closed
Door
Inner Trolley
Outer Trolley
Correct Angle
Door Arm
Connector Hole
Door with
Backward Slant
(Incorrect)
Open Door
26
WARNING
ADJUSTMENT STEP 1
Adjust the UP and DOWN Travel Limits
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED
or KILLED by a closing garage door.
• Incorrect adjustment of garage door travel limits will
interfere with proper operation of safety reversal system.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on contact
with 1-1/2" high (3.8 cm) object (or 2x4 laid flat) on floor.
CAUTION
Limit adjustment settings regulate the points at which the
door will stop when moving up or down.
To operate the opener, press the Door Control push bar.
Run the opener through a complete travel cycle.
• Does the door open and close completely?
• Does the door stay closed and not reverse
unintentionally when fully closed?
If your door passes both of these tests, no limit
adjustments are necessary unless the reversing test fails
(Adjustment Step 3, page 29).
Adjustment procedures are outlined below. Read the
procedures carefully before proceeding to Adjustment
Step 2. Use a screwdriver to make limit adjustments.
Run the opener through a complete travel cycle after
each adjustment.
NOTE: Repeated operation of the opener during
adjustment procedures may cause the motor to overheat
and shut off. Simply wait 15 minutes and try again.
If anything interferes with the door’s upward travel, it will
stop. If anything interferes with the door’s downward
travel (including binding or unbalanced doors), it will
reverse.
WARNING
CAUTION
To prevent damage to vehicles, be sure fully open door
provides adequate clearance.
HOW AND WHEN TO ADJUST THE LIMITS
• If the door does not open completely but opens at
least 5 feet (1.5 m):
Increase up travel. Turn the UP limit adjustment screw
clockwise. One turn equals 2" (5 cm) of travel.
• If door does not open at least 5 feet (1.5 m):
Adjust the UP (open) force as explained in Adjustment
Step 2.
Limit Adjustment Screws
Left Side Panel
• If the door does not close completely:
Increase down travel. Turn the down limit adjustment
screw counterclockwise. One turn equals 2" (5 cm) of
travel.
If door still won't close completely try lengthening the
door arm (page 25) and decreasing the down limit.
ADJUSTMENT LABEL
Test the door for binding: Pull the emergency release
handle. Manually open and close the door. If the door
is binding or unbalanced, call for a trained door
systems technician. If the door is balanced and not
binding, adjust the DOWN (close) force. See
Adjustment Step 2.
• If the opener reverses in fully closed position:
Decrease down travel. Turn the down limit adjustment
screw clockwise. One turn equals 2" (5 cm) of travel.
• If the door reverses when closing and there is no
visible interference to travel cycle:
If the opener lights are flashing, the Safety Reversing
Sensors are either not installed, misaligned, or
obstructed. See Troubleshooting, page 22.
27
WARNING
ADJUSTMENT STEP 2
Adjust the Force
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED
or KILLED by a closing garage door.
• Too much force on garage door will interfere with proper
operation of safety reversal system.
• NEVER increase force beyond minimum amount required to
close garage door.
• NEVER use force adjustments to compensate for a binding
or sticking garage door.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on contact
with 1-1/2" high (3.8 cm) object (or 2x4 laid flat) on floor.
CAUTION
Force adjustment controls are located on the back panel
of the motor unit. Force adjustment settings regulate the
amount of power required to open and close the door.
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down direction
and stops in the up direction. Weather conditions can
affect the door movement, so occasional adjustment may
be needed.
The maximum force adjustment range is about 3/4 of
a complete turn. Do not force controls beyond that
point. Turn force adjustment controls with a screwdriver.
NOTE: If anything interferes with the door’s upward
travel, it will stop. If anything interferes with the door’s
downward travel (including binding or unbalanced doors),
it will reverse.
HOW AND WHEN TO ADJUST THE FORCES
1. Test the DOWN (close) force
• Grasp the door bottom when the door is about
halfway through DOWN (close) travel. The door
should reverse. Reversal halfway through down travel
does not guarantee reversal on a 1-1/2" (3.8 cm)
obstruction. See Adjustment Step 3, page 29. If the
door is hard to hold or doesn't reverse,
DECREASE the DOWN (close) force by turning
the control counterclockwise. Make small adjustments
until the door reverses normally. After each
adjustment, run the opener through a complete cycle.
• If the door reverses during the down (close) cycle
and the opener lights aren't flashing, INCREASE
DOWN (close) force by turning the control clockwise.
Make small adjustments until the door completes a
close cycle. After each adjustment, run the opener
through a complete travel cycle. Do not increase the
force beyond the minimum amount required to close
the door.
2. Test the UP (open) force
• Grasp the door bottom when the door is about
halfway through UP (open) travel. The door should
stop. If the door is hard to hold or doesn't stop,
DECREASE UP (open) force by turning the control
counterclockwise. Make small adjustments until the
door stops easily and opens fully. After each
adjustment, run the opener through a complete travel
cycle.
• If the door doesn’t open at least 5 feet (1.5 m),
INCREASE UP (open) force by turning the control
clockwise. Make small adjustments until door opens
completely. Readjust the UP limit if necessary. After
each adjustment, run the opener through a complete
travel cycle.
Force
Adjustment
Controls
Back Panel
KG
KG
Antenna
FORCE ADJUSTMENT LABEL
9
1
7
3
1
7
3
5
5
KG
KG
Open Force
28
9
Close Force
WARNING
ADJUSTMENT STEP 3
Test the Safety Reversal System
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED
or KILLED by a closing garage door.
• Safety reversal system MUST be tested every month.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on contact
with 1-1/2" high (3.8 cm) object (or 2x4 laid flat) on the
floor.
CAUTION
TEST
• With the door fully open, place a 1-1/2" (3.8 cm) board
(or a 2x4 laid flat) on the floor, centered under the
garage door.
• Operate the door in the down direction. The door must
reverse on striking the obstruction.
ADJUST
• If the door stops on the obstruction, it is not traveling
far enough in the down direction. Increase the DOWN
limit by turning the DOWN limit adjustment screw
counterclockwise 1/4 turn.
NOTE: On a sectional door, make sure limit
adjustments do not force the door arm beyond a
straight up and down position. See the illustration on
page 25.
• Repeat the test.
• When the door reverses on the 1-1/2" (3.8 cm) board,
remove the obstruction and run the opener through 3
or 4 complete travel cycles to test adjustment.
• If the unit continues to fail the Safety Reverse Test, call
for a trained door systems technician.
IMPORTANT SAFETY CHECK:
Test the Safety Reverse System after:
• Each adjustment of door arm length, limits, or force
controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
1-1/2" (3.8 cm) board
(or a 2x4 laid flat)
WARNING
ADJUSTMENT STEP 4
Test The Protector System
®
Without a properly installed safety reversing sensor, persons
(particularly small children) could be SERIOUSLY INJURED
or KILLED by a closing garage door.
CAUTION
• Press the remote control push button to open the door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the door.
The door will not move more than an inch (2.5 cm),
and the opener lights will flash.
The garage door opener will not close from a remote if
the indicator light in either sensor is off (alerting you to
the fact that the sensor is misaligned or obstructed).
If the opener closes the door when the safety
reversing sensor is obstructed (and the sensors are
no more than 6" (15 cm) above the floor), call for a
trained door systems technician.
Safety Reversing Sensor
29
Safety Reversing Sensor
WARNING
OPERATION
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
2. ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate or play with garage door
control push buttons or remote controls.
3. ONLY activate garage door when it can be seen clearly, it is
properly adjusted, and there are no obstructions to door
travel.
4. ALWAYS keep garage door in sight until completely closed.
NO ONE SHOULD CROSS THE PATH OF THE MOVING
DOOR.
5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY
OPENED DOOR.
6. If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
7. NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
8. NEVER use handle to pull garage door open or closed. If
rope knot becomes untied, you could fall.
9. If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
10. After ANY adjustments are made, the safety reversal
system MUST be tested.
11. Safety reversal system MUST be tested every month.
Garage door MUST reverse on contact with 1-1/2" high
(3.8 cm) object (or a 2x4 laid flat) on the floor.
12. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED
(see page 3). An improperly balanced door may not
reverse when required and could result in SEVERE INJURY
or DEATH.
13. ALL repairs to cables, spring assemblies and other
hardware, ALL of which are under EXTREME tension,
MUST be made by a trained door systems technician.
14. ALWAYS disconnect electric power to garage door opener
BEFORE making ANY repairs or removing covers.
15.
Using Your Garage Door Opener
SAVE THESE INSTRUCTIONS.
6. If obstructed while opening, the door will stop.
7. If fully open, the door will not close when the beam is
broken. The sensor has no effect in the opening cycle.
If the sensor is not installed, or is misaligned, the door
won't close from a hand-held remote. However, you can
close the door with the Door Control, the Outdoor Key
Switch, or Keyless Entry, if you activate them until down
travel is complete. If you release them too soon, the door
will reverse.
The opener lights will turn on under the following
conditions: when the opener is initially plugged in; when
power is restored after interruption; when the opener is
activated.
They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature on the
Multi-Function Door Control Panel is activated. Bulb size
is A19. Bulb power is 100 watts maximum.
Security✚® light feature: Lights will also turn on when
someone walks through the open garage door. With a
Multi-Function Door Control Panel, this feature may be
turned off as follows: With the opener lights off, press
and hold the light button for 10 seconds, until the light
goes on, then off again. To restore this feature, start with
the opener lights on, then press and hold the light button
for 10 seconds until the light goes off, then on again.
Your Security✚® opener and hand-held remote control
have been factory-set to a matching code which changes
with each use, randomly accessing over 100 billion new
codes. Your opener will operate with up to eight
Security✚® remote controls and one Security✚® Keyless
Entry System. If you purchase a new remote, or if you
wish to deactivate any remote, follow the instructions in
the Programming section.
Activate your opener with any of the following:
• The hand-held Remote Control: Hold the large push
button down until the door starts to move.
• The wall-mounted Door Control: Hold the push button
or bar down until the door starts to move.
• The Keyless Entry (See Accessories): If provided with
your garage door opener, it must be programmed
before use. See Programming.
When the opener is activated (with the safety
reversing sensor correctly installed and aligned)
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop.
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse. If the
obstruction interrupts the sensor beam, the opener
lights will blink for five seconds.
30
Using the Wall-Mounted Door Control
THE MULTI-FUNCTION DOOR
CONTROL
Press the lighted push button to
open or close the door. Press again
to reverse the door during the
closing cycle or to stop the door
while it's opening.
To Open the Door Manually
WARNING
Lighted
Push Button
To prevent possible SERIOUS INJURY or DEATH from a
falling garage door:
• If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or
broken springs or unbalanced door could result in an open
door falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope knot
becomes untied, you could fall.
CAUTION
Lock
Button
LOCK
LIGHT
Light
Button
Light feature
Press the Light button to turn the opener light on or off. It
will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the
light will remain on for 4-1/2 minutes. Press again to turn
it off sooner. The 4-1/2 minute interval can be changed to
1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold
the Lock button until the light blinks (about 10 seconds).
A single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
DISCONNECT THE TROLLEY:
The door should be fully
closed if possible. Pull down
on the emergency release
handle (so that the trolley
release arm snaps into a
vertical position) and lift the
door manually.
The lockout feature prevents
the trolley from reconnecting
automatically, and the door
can be raised and lowered
manually as often as necessary.
Lock feature
Designed to prevent operation of the door from
hand-held remote controls. However, the door will open
and close from the Door Control, the Outdoor Keylock
and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2
seconds. The push button light will flash as long as the
Lock feature is on.
To turn off, press and hold the Lock button again for
2 seconds. The push button light will stop flashing. The
Lock feature will also turn off whenever the “learn” button
on the motor unit panel is activated.
Trolley
Trolley Release
Arm (in Manual
Disconnect Position)
NOT
ICE
Lockout position
(Manual disconnect)
Trolley
TO RE-CONNECT THE
TROLLEY:
Pull the emergency release
handle toward the opener at
an angle so that the trolley
Emergency
Release Handle
release arm is horizontal.
(Pull at 45° angle)
The trolley will reconnect on
the next UP or DOWN operation, To reconnect
either manually or by using the
door control or remote.
Additional feature when used with the 3-Button
hand-held remote
To control the opener lights:
In addition to operating the door, you
may program the remote to operate the
lights.
1. With the door closed, press and hold
a small remote button that you want
to control the light.
2. Press and hold the Light button on the door control.
3. While holding the Light button, press and hold the Lock
button on the door control.
4. After the opener lights flash, release all buttons.
E
NOTIC
31
Trolley
Release
Arm
THE REMOTE CONTROL BATTERY
CARE OF YOUR OPENER
LIMIT AND FORCE ADJUSTMENTS:
Weather conditions may cause some
minor changes in door operation
9
1
requiring some re-adjustments,
7
3
kg
kg
5
particularly during the first year of
operation.
FORCE CONTROLS
Pages 27 and 28 refer to the limit and
force adjustments. Only a screwdriver
is required. Follow the instructions carefully.
Repeat the safety reverse test
LIMIT CONTROLS
(Adjustment Step 3, page 29) after
any adjustment of limits or force.
WARNING
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
CAUTION
L
The lithium battery should produce power for up to
5 years.
WARNING
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 100°C (212°F)
or incinerate.
CAUTION
MAINTENANCE SCHEDULE
Once a Month
• Manually operate door. If it is unbalanced or binding,
call a trained door systems technician.
• Check to be sure door opens & closes fully. Adjust
limits and/or force if necessary. (See pages 27 and 28)
• Repeat the safety reverse test. Make any necessary
adjustments. (See Adjustment Step 3)
Once a Year
• Oil door rollers, bearings and hinges. The opener does
not require additional lubrication. Do not grease the
door tracks.
To replace battery, use the visor
clip or screwdriver blade to pry
open the case as shown. Insert
battery positive side up (+).
Dispose of old battery properly.
Replace the battery with only
3V2032 coin cell batteries.
Battery
positive
side up (+)
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
32
HAVING A PROBLEM?
Bell Wire
1. My door will not close and the light bulbs blink on
my motor unit: The safety reversing sensor must be
connected and aligned correctly before the garage
door opener will move in the down direction.
• Verify the safety sensors are properly installed,
aligned and free of any obstructions. Refer to
Installation Step 4: Install The Protector System®.
• Check diagnostic LED for flashes on the motor unit
then refer to the Diagnostic Chart on the following
page.
KG
Safety Reversing Sensor
2. My remotes will not activate the door:
• Verify your Premium door control is not blinking. If it
is blinking, deactivate the Lock Mode following the
instructions for Using the Multi-Function Door
Control.
• Reprogram remotes following the programming
instructions. Refer to Programming.
• If remote will still not activate your door, check
diagnostic LED for flashes on motor unit then refer to
Diagnostic Chart on the following page.
Sending Eye Safety Reversing
Sensor (Amber Indicator Light)
3. My door reverses for no apparent reason: Repeat
safety reverse test after adjustments to force or travel
limits. The need for occasional adjustment for the force
and limit settings is normal. Weather conditions in
particular can affect door travel.
• Manually check door for balance or any binding
problems.
• Refer to Adjustment Step 2, Adjust the Force.
KG
"Learn"
Button
LED or
Diagnostic LED
Receiving Eye Safety Reversing
Sensor (Green Indicator Light)
5. My lights will not turn off when door is open:
• The garage door opener is equipped with a security
light feature. This feature activates the light on when
the safety sensor beam has been obstructed. Refer
to Operation section; Using the Wall Mounted Door
Control, Light Feature.
4. My door reverses for no apparent reason after fully
closing and touching the floor: Repeat safety
reverse test after adjustments to force or travel limits.
The need for occasional adjustment for the force and
limit settings is normal. Weather conditions in particular
can affect door travel.
• Refer to Adjustment Step 1, Adjust the UP and
DOWN Travel Limits. Decrease down travel by
turning down limit adjustment screw clockwise.
33
Diagnostics
Located On
Motor Unit
KG
KG
Installed
Safety Reversing
Sensor
LED or
Diagnostic
LED
"Learn"
Button
Safety Reversing Sensor
Diagnostic Chart
1 FLASH
Safety reversing sensors
wire open (broken or
disconnected).
OR
2 FLASHES
Safety reversing sensors
wire shorted or
black/white wire
reversed.
3 FLASHES
Door control or
wire shorted.
4 FLASHES
Safety reversing sensors
slightly misaligned
(dim or flashing LED).
5 FLASHES
Motor overheated or
possible RPM sensor
failure. Unplug to reset.
6 FLASHES
Motor Circuit Failure.
Replace Receiver
Logic Board.
Your garage door opener is programmed with self-diagnostic
capabilities. The “Learn” button/diagnostic LED will flash a
number of times then pause signifying it has found a potential
issue. Consult Diagnostic Chart below.
Symptom: One or both of the Indicator lights on the safety sensors do
not glow steady.
• Inspect sensor wires for a short (staple in wire), correct wiring polarity (black/white
wires reversed), broken or disconnected wires, replace/attach as needed.
• Disconnect all wires from back of motor unit.
• Remove sensors from brackets and shorten sensor wires to 1-2 ft (30-60 cm) from
back each of sensor.
• Reattach sending eye to motor unit using shortened wires. If sending eye indicator
light glows steadily, attach the receiving eye.
• Align sensors, if the indicator lights glow replace the wires for the sensors. If the
sensor indicator lights do not light, replace the safety sensors.
Symptom: LED is not lit on door control.
• Inspect door control/wires for a short (staple in wire), replace as needed.
• Disconnect wires at door control, touch wires together. If motor unit activates,
replace door control.
• If motor unit does not activate, disconnect door control wires from motor unit.
Momentarily short across red and white terminals with jumper wire. If motor unit
activates, replace door control wires.
Symptom: Sending indicator light glows steadily, receiving indicator light is
dim or flashing.
• Realign receiving eye sensor, clean lens and secure brackets.
• Verify door track is firmly secured to wall and does not move.
Symptom: Motor has over heated; the motor unit does not operate;
RPM Sensor = Short travel 6-8" (15-20 cm).
• Unplug unit to reset. Try to operate motor unit, check diagnostic code.
• If it is still flashing 5 times and motor unit moves 6-8" (15-20 cm), replace RPM
sensor.
• If motor unit doesn’t operate, motor unit is overheated. Wait 30 minutes and retry. If
motor unit still will not operate replace logic board.
Symptom: Motor unit doesn’t operate.
• Replace logic board because motor rarely fails.
34
PROGRAMMING
NOTICE: If this Security✚® garage door opener is operated with a non-rolling code transmitter, the technical measure in
the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The
owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code
transmitter to circumvent that technical measure.
Your garage door opener has already been programmed at the factory to operate with your hand-held remote control.
The door will open and close when you press the large push button.
Below are instructions for programming your opener to operate with additional Security✚® remote controls.
To Add or Reprogram a Hand-held Remote Control
USING THE “LEARN” BUTTON
USING THE MULTI-FUNCTION DOOR CONTROL
9
1
7
3
5
KG
9
1
7
3
5
KG
LOCK
LIGHT
1. Press and release the “learn” button
on the motor unit. The learn indicator
light will glow steadily for 30 seconds.
1. Press and hold the button on the
hand-held remote* that you wish to
operate your garage door.
2. Within 30 seconds, press and hold the
button on the hand-held remote* that
you wish to operate your garage door.
2. While holding the remote button,
press and hold the LIGHT button on
the Multi-Function Door Control.
LOCK
LIGHT
3. Continue holding both buttons while
you press the push bar on the MultiFunction Door Control (all three
buttons are held).
3. Release the button when the motor
unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
LOCK
LIGHT
4. Release buttons when the motor unit
lights blink. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.
To Erase All Codes From Motor Unit
Memory
*3-Button Remotes
If provided with your garage
door opener, the large button
is factory programmed to
operate it. Additional buttons
on any Security✚® 3-Button
remote or compact remote
can be programmed to
operate other Security✚®
garage door openers.
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on
motor unit until the learn indicator light
goes out (approximately 6 seconds). All
previous codes are now erased.
Reprogram each remote or keyless entry
you wish to use.
35
To Add, Reprogram or Change a Keyless Entry PIN
NOTE: Your new Keyless Entry must be programmed to operate your garage door opener.
USING THE “LEARN” BUTTON
USING THE MULTI-FUNCTION DOOR CONTROL
LO C K
L IG H T
1. Press and release the “learn” button
on motor unit. The learn indicator
light will glow steadily for 30
seconds.
2. Within 30 seconds, enter a four digit
personal identification number (PIN)
of your choice on the keypad. Then
press and hold the ENTER button.
3. Release the button when the motor
unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
NOTE: This method requires two people if the Keyless
Entry is already mounted outside the garage.
1. Enter a four digit personal
identification number (PIN) of your
choice on the keypad. Then press
and hold ENTER.
2. While holding the ENTER button,
press and hold the LIGHT button on
the Multi-Function Door Control.
LOCK
LIGHT
3. Continue holding the ENTER and
LIGHT buttons while you press the
push bar on the Multi-Function Door
Control (all three buttons are held).
LOCK
To change an existing, known PIN
If the existing PIN is known, it may be changed by one
person without using a ladder.
1. Press the four buttons for the present PIN, then press
and hold the # button.
The opener light will blink twice. Release the # button.
2. Press the new 4-digit PIN you have chosen, then
press Enter.
The motor unit lights will blink once when the PIN has been
learned.
Test by pressing the new PIN, then press Enter. The door
should move.
To set a temporary PIN
You may authorize access by visitors or service people with
a temporary 4-digit PIN. After a programmed number of
hours or number of accesses, this temporary PIN expires
and will no longer open the door. It can be used to close the
door even after it has expired. To set a temporary PIN:
1. Press the four buttons for your personal entry PIN (not
the last temporary PIN), then press and hold the ✽
button.
The opener light will blink three times. Release the
button.
LIGHT
4. Release buttons when the motor unit
lights blink. It has learned the code. If
light bulbs are not installed, two
clicks will be heard.
2. Press the temporary 4-digit PIN you have chosen, then
press Enter.
The opener light will blink four times.
3. To set the number of hours this temporary PIN will work,
press the number of hours (up to 255), then press ✽.
OR
3. To set the number of times this temporary PIN will work,
press the number of times (up to 255), then press #.
The opener light will blink once when the temporary PIN has
been learned.
Test by pressing the four buttons for the temporary PIN, then
press Enter. The door should move. If the temporary PIN
was set to a certain number of openings, remember that the
test has used up one opening.To clear the temporary
password, repeat steps 1-3, setting the number of hours or
times to 0 in step 3.
One Button Close: Opener can be closed by pressing only the ENTER button if the one button close feature has been
activated. This feature has been activated at the factory. To activate or deactivate this feature press and hold buttons 1 and
9 for 10 seconds. The keypad will blink twice when the one button close is active. The keypad will blink four times when
one button close is deactivated.
36
REPAIR PARTS
Rail Assembly Parts
1
8
2
7
6
KEY PART
NO. NO.
5
4
3
Installation Parts
2
1
81C275
41A6263
3
4
5
12B890
12B900
41A6264
6
7
8
12B889
41A6262
41A4836
4
28A143
Rack
Hardware bag (includes
sprocket coupling)
Left rail bracket
Right rail bracket
Screw drive rail assembly
Complete 7' (2.1 m)
Rail support brace
Complete trolley assembly
Drive sprocket kit
NOT SHOWN
Rail Clips
3
KEY
NO.
LOCK
LIGHT
G
LIN
CEI
6
T
UN
MO
LY
ON
UP
7
5
NOT
1
2
DESCRIPTION
ICE
10
11
9
8
13
1
2
3
4
5
6
7
8
9
10
11
12
13
12
37
PART
NO.
41A5273-9
953D
10A20
29B137
41A2828
41B4494-1
41A4353
41A5047
41A5034
DESCRIPTION
Multi-function door control
3-Button remote control
3V 2032 Lithium battery
Visor clip
Emergency release rope & handle assy.
2-Conductor bell wire: white & white/red
Header bracket w/clevis pin & fastener
Door bracket w/clevis pin & fastener
Safety sensor kit: receiving and
sending eyes with 3' (.9 m) 2-conductor
bell wire attached
178B34
Straight door arm section
12B776
Hanging bracket
178B35
Curved door arm section
41A5266-1
Safety sensor bracket
NOT SHOWN
41A4675-11 Installation hardware bag (see page 7)
114A3330
Owner’s manual
114A3330SP Owner’s manual - Spanish
Motor Unit Assembly Parts
13
9a
9
1
10
2
14
6a
3
12
4
5
8
7
6
Brown
Wire
(Down)
Contact
LIMIT SWITCH ASSY.
DN
UP
Drive
Gear
Center Limit
Contact
11
14
(Up)
Contact
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
6a
7
31C568
41B4245
30B620
41A3150
41D4671
41A6241
20B21-1
41C4672
Drive shaft cover
Line cord
Capacitor – 1/2 HP
Terminal block w/screws
Limit switch assembly
Motor drive assy. complete
Drive belt
Screw drive RPM kit
8
9
9a
10
11
12
13
14
41A4837-1
41A6335
41A6334
41AS050R2
41A5525-53
41C22-1
175B88
108D79
Worm gear and retainer
Low voltage wire harness
High voltage wire harness
Receiver logic board assy.
Cover
Drive coupling hub
Light socket
Light lens
38
Grey
Wire
Yellow
Wire
ACCESSORIES
953D
3-Button Security✚® Remote Control:
956D
3-Button Mini-Remote Control with
Security✚®:
With key ring and fastening strip.
7702CB
Outside Quick Release:
Required for a garage with NO access
door.
CLLAD
Remote Light Control:
Enables homeowner to turn on a lamp,
television or other appliance from their
car with their garage door opener remote
or from anywhere in their home with an
additional Chamberlain Security✚®
remote.
41A5281
Extension Brackets:
(Optional) For safety sensor installation
onto the wall or floor.
To order call: 1-800-528-9131.
Includes visor clip.
935CB
Motion Detecting Control Panel:
Multi-function door control with motion
sensor that automatically turns opener
lights on for 5 minutes when it detects a
person entering the garage. Sensor can
be easily deactivated when desired.
LOCK
LIGHT
940D
SECURITY✚® Keyless Entry:
Enables homeowner to operate garage
door opener from outside by entering a
password on a specially designed
keyboard. Also can add a temporary
password for visitors or service persons.
This temporary password can be limited
to a programmable number of hours or
entries.
CLDM1
CLOSED
OPEN
7806CB
Garage Door Monitor:
Monitors the status of your garage door
from inside your home. Includes monitor
and 1 garage door transmitter. Additional
transmitters available Order CLDM2 (Limit 3 transmitters per
monitor).
8 Foot (2.4 m) Rail Extension Kit:
To allow an 8 foot (2.4 m) door to open fully.
39
HOW TO ORDER
REPAIR PARTS
CHAMBERLAIN® SERVICE
IS ON CALL
Selling prices will be furnished on request or parts will be
shipped at prevailing prices and you will be billed
accordingly.
OUR LARGE SERVICE ORGANIZATION
SPANS AMERICA
INSTALLATION AND SERVICE INFORMATION IS AS NEAR
AS YOUR TELEPHONE. SIMPLY DIAL OUR TOLL FREE
NUMBER:
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
• PART NUMBER
• PART NAME
• MODEL NUMBER
1-800-528-9131
ADDRESS ORDERS TO:
www.chamberlain-diy.com
For professional installation, parts and service, contact
your local CHAMBERLAIN dealer. Look for him in the Yellow
Pages, or call our Service number for a list of dealers in
your area.
THE CHAMBERLAIN GROUP, INC.
Technical Support Group
6020 S. Country Club Road
Tucson, Arizona 85706
SERVICE INFORMATION TOLL FREE NUMBER:
1-800-528-9131
CHAMBERLAIN ONE-YEAR LIMITED WARRANTY
LIFETIME MOTOR WARRANTY
®
The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free
from defect in materials and/or workmanship for a period of one year from the date of purchase [and that the motor is free from defect in materials and/or workmanship
for the lifetime of the product]. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation,
maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety.
If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-9131, toll free, before dismantling this
product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call. Please
include a brief description of the problem and a dated proof-of-purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty
repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller's sole option) at no cost
to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller's sole option.
ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE ONE YEAR LIMITED WARRANTY PERIOD SET FORTH ABOVE [EXCEPT THE IMPLIED
WARRANTIES WITH RESPECT TO THE MOTOR, WHICH IS LIMITED IN DURATION TO THE LIFETIME OF THE PRODUCT], AND NO IMPLIED WARRANTIES
WILL EXIST OR APPLY AFTER SUCH PERIOD. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may
not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION
OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED
REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF
BATTERIES AND LIGHT BULBS OR UNITS INSTALLED FOR NON-RESIDENTIAL USE.
THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE,
INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT
COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE
ITEMS COULD RESULT IN A FEE TO YOU.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH
USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER'S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT,
NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY
OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This
limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
114A3330
© 2007, The Chamberlain Group, Inc.
All Rights Reserved