Owner`s manual | Chamberlain ATS211R Garage Door Opener User Manual

The Chamberlain Group, Inc.
845 Larch Avenue,
Elmhurst, Illinois 60126
®
MODEL ATS 211R
COMMERCIAL DOOR OPENER
For Residential and Light Duty Commercial Use
Install on Sectional Doors Only
L
O
W
H
I
G
H
L
A
NO R
M
H
I
G
H
L
O
W
L
A
NO R
M
WN
DORCE
FO
UP E
RC
FO
TM
OWNER'S MANUAL
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
■ The door WILL NOT CLOSE unless the Protector System® is connected
and properly aligned.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model number label is located on the operator cover.
CONTENTS
PAGE
CONTENTS
A review of safety alert symbols ..............................2
You'll need tools ......................................................3
Illustration of door installation .................................4
Opener carton inventory ..........................................5
Hardware inventory .................................................5
PAGE
Connect the door arm to the trolley ....................20
Adjustment Section – Pages 21 - 23
Travel limit adjustments.......................................21
Force adjustments ...............................................22
Test the Protector System® ..................................23
Test the safety reverse system............................23
Operation safety instructions .................................24
Care of your opener...............................................24
Maintenance schedule...........................................24
Operation of your opener.......................................25
Operation of Optional Accessories:
Model 96LM Remote Control ..............................26
Model 58LM Door Control...................................27
Model 68LM Door Control...................................28
Model 67LM Keyless Entry .................................29
Having a problem?..........................................30, 31
Repair parts, rail assembly ...................................32
Repair parts, installation .......................................32
Repair parts, opener assembly.............................33
Accessories ..........................................................34
Index .....................................................................35
How to order repair parts ......................................36
Warranty ...............................................................36
Assembly Section – Pages 6 - 7
Fasten the rail to the opener..................................6
Attach the chain to the sprocket ............................6
Install the rail support bracket................................6
Tighten the chain ...................................................7
Installation Section – Pages 8 - 20
Installation instruction warnings.............................7
Determine the header bracket location..................8
Install the header bracket ......................................9
Attach the rail to the header bracket....................10
Position the opener..............................................11
Hang the opener..................................................12
Install the door control .........................................13
Install the light......................................................14
Attach manual release handle .............................14
Electrical requirements ........................................15
The Protector System® .........................................16
Install the safety reversing sensor ..................17,18
Fasten the door bracket and plate ......................19
Start by reviewing these important safety alert symbols
When you see these Safety Symbols on the following pages, they will alert you to the possibility of
serious injuries or death if you do not comply with the corresponding instructions. The hazard may
come from something mechanical or from electric shock. Read the instructions carefully.
WARNING
WARNING
Mechanical
Electrical
When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage
to your garage door and/or the garage door opener if you do not comply with the corresponding
instructions. Read the instructions carefully.
CAUTION
This garage door opener is designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the safety instructions contained in this manual.
2
You'll Need Tools
During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below.
Pencil
Carpenter's
Level
1
Hack Saw
2
Tape Measure
Wire Cutters
Claw Hammer
Drill
3/16", 5/16" and
5/32" Drill Bits
Stepladder
Pliers
Screwdriver
1/2" and 7/16" Sockets
and Wrench
Adjustable End Wrench
CAUTION
WARNING
To avoid damage to the garage door and
opener, disable locks before installing and
operating the opener. Use a wood screw or nail
to hold locks in the "open" (unlocked)
position.
Operation at other than 120V 60 Hz will cause
opener malfunction and damage.
An unbalanced garage door might not reverse
when required and someone under the door
could be seriously injured or killed.
If your garage door binds, sticks or is out of
balance, call for professional garage door
service. Garage doors, door springs, cables,
pulleys, brackets and their hardware, are
under extreme tension and can cause serious
injury or death. Do not try to loosen, move or
adjust them yourself!
Ropes left on a garage door could cause
someone to become entangled and killed.
Remove all ropes connected to the door before
installing and operating the opener.
This product is for use on sectional garage
doors only. Serious personal injury could
result from the use of this product on onepiece garage doors.
Identify the type and height of your door, any special
conditions that exist, and any additional materials
that may be required by referring to the lists on
page 4.
Before you begin, complete the following test to
make sure your door is balanced and is not
sticking or binding:
• Lift the door about halfway as shown. Release the
door. It should stay in place, supported entirely by
its springs.
• Raise and lower the door to see if there is any
binding or sticking.
3
Before you begin, survey your garage area. Do any of the following conditions apply to you?
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with glass panels, etc.).
See page 19 for details.
FINISHED CEILING
Support bracket &
fastening hardware
is required.
See page 12.
Slack in chain tension
is normal when
garage door is closed.
Header Wall
Extension Spring
OR
Torsion Spring
———
Access Door
Door Center
———
——
Safety
Reversing
Sensor
Floor must be level
across width of door
Safety Reversing Sensor
Closed Position
Header Chain Pulley
Bracket
Bracket
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton.
• Step 1, page 8 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
• Step 5, page 12 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware may be required.
• Safety reversing sensor, page 16 - Depending
upon garage construction, wood blocks may need
to be fastened to mounting locations before
sensors are installed.
• Step 10, page 17 - Alternate floor mounting of the
safety reversing sensor will require hardware not
provided.
• Step 11, page 19 - Do you have a steel, aluminum,
fiberglass or glass panel door? If so, horizontal
and vertical reinforcement is required.
• Look at the garage door where it meets the floor.
It must close on the floor all the way across. Otherwise, the safety reverse system may not work
properly. Floor or door should be repaired. See
page 23.
• If your door is more than 7 feet high, see longer
rails available on page 34.
Chain
Trolley
Garage
Door
Spring
Straight
Door
Arm
Header
Wall
Rail
Manual
Release
Rope & Handle
Curved
Door
Arm
Door Bracket
Garage
Door
• The opener can be installed within 2 feet to the left or
right of the door center if there is a torsion spring or
center bearing plate in the way of the header bracket
or door bracket area. If your door has extension
springs, the opener must be installed in the center of
the door. See pages 8 and 19.
Do you have an access door in addition to the garage
door? If not, Model 1702 Outside Quick Release is
required. See page 34.
You may find it helpful to refer back to this page as
you proceed with the installation of your opener.
4
Opener Carton Inventory
Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is
missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and
installation is listed below.
LY
NT
ON
OU
GM
ILIN
CE
UP
Mounting Hardware
(Rail Support Bracket)
Header Bracket with
Clevis Pin and Fastener
Rail Support
Bracket
Lighted Door
Control Button
Styrofoam
Door Bracket
Door Bracket Plate
"C" Wrap (2)
Chain
Safety Reversing Sensor
Mounting Bracket
With Slot (2)
Curved Door Arm
Safety Reversing Sensor
Mounting Bracket
With Square Holes (2)
Rail
Straight
Door Arm
2 -Conductor Bell Wire
White & White/Red
Safety Labels
and
Literature
Trolley
Chain
Pulley Bracket
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with
2-Conductor White & White/Black Bell Wire
attached
Hardware Inventory
Assembly Hardware
5/16"-18x1/2" Washered Screw,
(2) (Mounted in Opener)
1/4"-20x5/8" Hex Screw (2)
1/4"-20x5/8" Lock Washer (2)
#8-32x3/8" Screw (1)
5/16"-18x1/2" Washered Screw (2)
Installation Hardware
Hex Screw 5/16"-18x7/8" (4)
Nut 5/16"-18 (4)
Lock Washer 5/16" (4)
Rail Grease
Lag Screw 5/16"-9x1-5/8" (2)
Lag Screw 5/16"-18x1-7/8" (2)
Screw 6ABx1-1/2" (2)
Handle
Ring Fastener (3)
Self-Threading Screw 1/4"-14x5/8"
Insulated Staples (10)
Dry Wall Anchors (2)
Clevis Pin 5/16"x2-3/4" (1)
Clevis Pin 5/16"x1" (2)
Rope
5
Hardware for Safety Reversing
Sensor
Lag Screw 1/4x1-1/2" (4)
Carriage Bolt 1/4"-20x1/2" (4)
Lock Nut 1/4"-20 (4)
Wing Nut (2)
Hex Screw 1/4-20x1-1/2" (2)
Screw #10-32x3/8" (4)
Lock Nut #10x32 (4)
Insulated Staples (20)
Assembly Section: Pages 6 – 7
Assembly Step 1
CAUTION
Attach the Rail to the Opener
To fasten rail, use only those screws mounted
in the top of the opener. Any other screws will
cause serious damage to the opener.
• Place the opener on packing material to protect
the cover.
• Remove the (2) 5/16"-18x1/2" washered screws
mounted in the top of the opener.
• Align rail at an angle with opener so one hole in
rail and opener line up.
• Thread one of the washered screws part way in.
Use only these screws! Use of any other screws
will cause serious damage to door opener.
• Cut tape from rail, chain and styrofoam.
• REMOVE STYROFOAM.
USE ONLY THIS
TYPE AND SIZE
SCREW
Washered Screw
5/16"-18x1/2"
Rail
Hole
Styrofoam
Packaging
Rail
Chain
Opener
Assembly Step 2
WARNING
Attach the Chain to the Sprocket
& Install the Rail Support Bracket
Serious injury can result if fingers become
entangled in moving opener sprocket. Attach
rail support bracket securely. Never operate
opener while you hand is near the opener
sprocket.
• Guide the chain over chain spreader and opener
sprocket. If necessary, loosen the outer nut on the
trolley to obtain more chain slack. Insert the
second washered screw. CAUTION! Use only the
screw previously removed from opener.
• Tighten both screws securely through the rail into
the opener as shown.
• Position the rail support bracket on the opener.
• Attach the bracket to the rail with 1/4"-20x5/8" hex
screws and lock washers.
• Attach the bracket to the opener by inserting a
5/16"-18x1/2" washered screw through a hole in
each side flange and a matching hole in the bracket.
Complete the connection by inserting the
#8-32x3/8" screw through the back flange and the
hole in rail support.
Washered Screw
5/16"-18x1/2"
Chain
Spreader
USE ONLY THIS
TYPE AND SIZE
SCREW
Sprocket
1/4"-20x5/8" Hex Screws
with Lock Washers
5/16"-18x1/2"
Washered Screw
#8-32x3/8"
Screw
Chain
5/16"-18x1/2"
Washered Screw
Rail Support
Bracket
Opener
Back Flange
Opener
Opener
Side Flange
Hardware Shown Actual Size
Hex Screw
1/4"-20x5/8"
Washered Screw
5/16"-18x1/2"
Lock Washer
Screw
#8-32x3/8"
6
Assembly Step 3
Tighten the Chain
Outer Nut
• Spin the inner nut and lock washer down the
threaded shaft, away from the trolley.
• To tighten the chain, turn outer nut in the direction
shown. As you turn the nut, keep the chain
from twisting.
• When the chain is approximately 1/2" above the
base of the rail at its midpoint, re-tighten the inner
nut to secure the adjustment.
Sprocket noise can result if chain is either too
loose or too tight.
When installation is complete, you may notice some
chain droop with the door closed. This is normal. If
the chain returns to the position shown when the
door is open, do not re-adjust the chain.
Lock
Washer
Inner Nut
To Tighten Outer Nut
To Tighten
Inner Nut
Trolley
Chain
1/2"
NOTE: During future maintenance, ALWAYS pull
the manual release handle to disconnect trolley
before adjusting chain.
Base of rail
You have now finished assembling your garage door opener. Please read the following
warnings before proceeding to the installation section:
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1.
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
2. Install only on a properly balanced and lubricated garage door. An improperly balanced door may
not reverse and could result in severe injury or death. Repairs to cables, spring assemblies and
other hardware must be made by a professional service person before installing opener.
3. Disable all locks and remove all ropes connected to the garage door before installing the opener.
Ropes connected to a garage door can cause entanglement and death.
4. If possible, install door opener 7 feet or more above floor with the manual release handle
mounted 6 feet above the floor.
5. Do not connect the opener to power source until instructed to do so.
6. Locate the Door Control within sight of the door at a minimum height of 5 feet where small
children cannot reach and away from all moving parts of the door.
7. Install the User Safety Instruction Label on the wall adjacent to the control button and the
Maintenance Instruction Label in a prominent location on the inside of the garage door.
8. Upon completion of the installation, the door must reverse when it comes in contact with a
one-inch high object or a 2x4 laid flat on the floor.
9. Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry or
loose clothing can be caught in the mechanism of the garage door or the opener.
7
Installation Section: Pages 8 – 20
Installation Step 1
WARNING
Determine Header Bracket Location
If the header bracket is not rigidly fastened to
a structural support on the header wall or
ceiling, the safety reverse system may not
work properly (see page 23). The door might
not reverse when required, and could cause
serious injury or death.
The garage door springs, cables, pulleys,
brackets and their hardware are under extreme
tension. Do not attempt to loosen, move or
adjust them yourself. Serious personal injury
or death could result. Call for professional
garage door service.
Header
Wall
Finished
Ceiling
Vertical
Guideline
2x4
Structural
Supports
Vertical
Guideline
• Open your door to the highest
point of travel as shown. Draw
an intersecting horizontal line
on the header wall 2" above
the high point. This height will
provide travel clearance for the
top edge of the door.
• Close the door and mark the inside
vertical centerline of the garage door.
• Extend the line onto the header wall
above the door.
Remember, you can fasten the
header bracket within 2 feet to the
left or right of the door center only if
a torsion spring or center bearing
plate is in the way; or you can attach
it to the ceiling (refer to page 9) when
clearance is minimal. (It may be
mounted on the wall upside down if
necessary, to gain approximately
1/2".)
If you need to install the header bracket
on a 2x4 (on wall or ceiling), use lag
screws (not supplied) to securely fasten
the 2x4 to structural supports as shown
here.
Ceiling
Header
Wall
2"
Highest Point
of Travel
Door
Proceed to Step 2, page 9.
8
Track
You can attach the header bracket either to the
wall above the garage door, or to the ceiling.
Follow the instructions which will work best for
your particular requirements.
Installation Step 2
Install the Header Bracket
Fasten the Header Bracket to the Wall
• Center the bracket on the vertical guideline with
the bottom edge of the bracket on the horizontal
line as shown (with the arrow pointing toward the
ceiling).
Header
Wall
Y
NL
TO
Wall
Mounting Holes
Vertical
Center
Line
UN
G
• Mark either set of bracket holes (do not use the
holes designated for ceiling mount). Drill 3/16" pilot
holes and fasten the bracket securely to a structural
support with the hardware provided.
Lag Screws
5/16"-9x1-5/8"
MO
ILIN
CE
UP
CEILING MOUNT ONLY
Header
Bracket
UP
2x4
Structural
Support
Door
Spring
The nail hole is for positioning
only. You must use lag screws to
mount the header bracket.
Optional Wall
Mounting Holes
Garage
Door
Highest
Point of Travel
(of Garage Door)
Hardware Shown Actual Size
Vertical
Center Line
Lag Screw
5/16"-9x1-5/8"
Fasten the Header Bracket to the Ceiling
• Extend the vertical guideline onto the ceiling as
shown.
• Center the bracket on the vertical mark, no more
than 6" from the wall. Make sure the arrow is
pointing toward the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal.
• Mark holes designated for ceiling mount only. Drill
3/16" pilot holes and fasten the bracket securely to
a structural support with the hardware provided.
Finished
Ceiling
Vertical
Center Line
Header
Bracket
UP
6" Maximum
Door
Spring
Ceiling Mounting Holes
Lag Screws
5/16"-9x1-5/8"
CEILING MOUNT ONLY
UP
Header
Wall
Garage
Door
The nail hole is for positioning only.
You must use lag screws to mount
the header bracket.
9
Vertical
Center Line
Installation Step 3
Attach the Rail to the Header Bracket
• Position the opener on the garage floor below the
header bracket. Use packing material as a
protective base.
If the door spring is in the way you'll need help.
Have someone hold the opener securely on a
temporary support to allow the rail to clear the
spring.
• Position the chain pulley bracket against the header
bracket.
• Align the bracket holes and join with a clevis pin as
shown.
• Insert a ring fastener to secure.
Header Wall
Header
Bracket
Chain
Pulley
Bracket
Ring Fastener
Rail
Header Bracket
Clevis Pin
5/16"x2-3/4 "
Chain
Pulley
Bracket
Rail
Garage
Door
Temporary
Support
Hardware Shown Actual Size
Clevis Pin
5/16" x 2-3/4"
Ring Fastener
10
Installation Step 4
CAUTION
Position the Opener
To prevent damage to steel, aluminum,
fiberglass or glass panel doors, do not rest the
opener on the door without using a 2x4.
You will need help at this point if the ladder is not
tall enough.
• Open the door all the way and place a 2x4 laid flat
on the top section beneath the rail.
A 2x4 laid flat is convenient for setting an ideal
door-to-rail distance.
• Raise the opener onto a stepladder.
Rail
2x4
Door
Stepladder
• If the top panel hits the trolley when you raise
the door, pull down on the trolley release arm
to disconnect the inner and outer sections. The
trolley can remain disconnected until Step 12
is completed.
Trolley
Release Arm
Trolley
11
Installation Step 5
WARNING
Hang the Opener
The opener could fall and injure someone if it
is not properly secured. Fasten the opener
securely to structural supports of the garage.
Two representative installations are shown.
Yours may be different. Hanging brackets should
be angled, Figure 1, to provide rigid support. On
finished ceilings, Figure 2, attach a sturdy metal
bracket to structural supports in ceiling before
installing the opener. The bracket and fastening
hardware are not supplied.
• Measure the distance from each side of the opener
to the structural support.
• Cut both pieces of the hanging bracket to required
lengths.
• Drill 3/16" pilot holes in the structural supports.
• Attach one end of each bracket to a support with
5/16"x1-7/8" lag screws.
• Fasten the opener to the hanging brackets with
5/16"-18x7/8" hex screws, lock washers and nuts.
• Check to make sure the rail is centered over the
door (or in line with the header bracket if the
bracket is not centered above the door).
• Remove the 2x4. Operate the door manually. If the
door hits the rail, raise the header bracket.
Grease the top and
underside of the rail surface
where the trolley slides. A
tube of grease is supplied.
Figure 1
Structural
Supports
Lag Screws
5/16"x1-7/8"
Measure
Distance
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Figure 2
E
AS
RE
IL G 3A4
.8
O
N
RA
Hidden
Support
FINISHED CEILING
Lag Screws
5/16"x1-7/8"
Bracket
(Not Supplied)
Hardware Shown Actual Size
Lag Screw
5/16"-18x1-7/8"
Hex Screw
5/16"-18x7/8"
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Nut 5/16"-18
Lock Washer 5/16"
12
(Not Supplied)
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Installation Step 6
WARNING
Install the Door Control
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause serious
injury or death.
Install the Door Control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control transmitter(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it clearly,
and there are no obstructions to door travel.
• Strip 1/4" of insulation from one end of the bell
wire; connect the wire to the two screw terminals
on the back of the Door Control: white to 2 and
white/red to 1.
• Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all
moving parts of the door and door hardware.
Fasten the Door Control Button securely with
6ABx1-1/2" screws. If installing into drywall, drill
5/32" holes and use the anchors provided.
• Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.
• Receiver terminal screws and the antenna are
located on the back panel of the opener. Position
the antenna wire as shown.
• Then connect the bell wire by color to the opener
terminal screws: white to 2 and white/red to 1.
• Remember to affix the User Safety Instruction
label to the wall near the door control, and the
Maintenance Instruction Label in a prominent
location on the inside of the garage door.
If the label adhesive will not adhere to your garage
wall surface (or becomes loose with time), use tacks
to secure the label alongside the door control.
Page 25 explains how to operate the opener using
the door control.
Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
full open position but will not return to the close
position until the sensor beam is connected and
properly aligned. See Safety Reversing Sensor
Instructions beginnning on page 16.
Outside Keylock Accessory Connections
To opener terminal screws:
White to 2 and white//red to 1
Hardware Shown Actual Size
6ABx1-1/2" Screw
Lighted Door Control Button
Multi-Function
Door Control Panel
Terminal Screws
-1
Insulated
Staples
Dry Wall Anchors
Opener
Terminal
Screws
2-Conductor
Bell Wire
-2
RED-1
1
WHT-2
BLK-3
2
3
Lock Button
2-Conductor
Bell Wire
9
1
7
3
9
1
7
5
KG
LOCK
LIGHT
Light Button
Door Control
Push Bar
Multi-Function
Door Control Panel
13
Back Panel
of Opener
3
5
KG
Antenna
Installation Step 7
Install the Light
75 Watt Max.
Light Bulb
Install the Light
• Install a 75 watt maximum light bulb in the socket.
The light will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the light will turn OFF.
• If the bulb burns out prematurely due to vibration,
replace with a "Garage Door Opener" bulb.
Opener
Installation Step 8
WARNING
Attach the Manual Release
Rope and Handle
Do not use the red handle to pull the door
open or closed. The rope knot could become
untied and you could fall. Use the manual
release only to disengage the trolley and, if
possible, only when the door is closed.
Garage doors are heavy. If the door is open
when the handle is pulled, the door could
close inadvertently if it is not properly
balanced. Serious injury may result to persons
under the door. Make sure the doorway is clear
of persons and obstructions before pulling
handle when door is open.
Overhand
Knot
Trolley
• Thread one end of the rope through the hole in the
top of the red handle so "NOTICE" reads right side
up as shown. Secure with an overhand knot.
The knot should be at least 1" from the end of the
rope to prevent slipping.
• Thread the other end of the rope through the hole in
the release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet above the
floor. Secure with an overhand knot.
If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
Trolley
Release Arm
Rope
NOT
ICE
Overhand
Knot
Manual
Release Handle
14
Installation Step 9
WARNING
Electrical Requirements
To prevent electrocution or fire, installation
and wiring must be in compliance with local
electrical and building codes.
Do NOT use an extension cord, 2-wire adapter,
or change the plug in any way to make it fit
your outlet.
To reduce the risk of electric shock, your garage
door opener has a grounding type plug with a third
grounding pin. This plug will only fit into a grounding
type outlet.
If the plug doesn't fit into the outlet you have,
contact a qualified electrician to install the
proper outlet.
To avoid installation difficulties,
do not run the opener at this time.
Right
Wrong
If permanent wiring is required by your local code, refer to the following procedure:
WARNING
To prevent electrocution, remove power from
the garage door opener and from the circuit
you plan to use for the permanent
connection.
To make a permanent connection through the 7/8"
diameter hole in the top of the opener (according
to local code):
• Remove the opener cover screws and set the
cover aside.
• Remove the attached 3-prong cord.
• Connect the black (line) wire to the screw on the
brass terminal; the white (neutral) wire to the
screw on the silver terminal; and the ground wire
to the green ground screw. The opener must be
grounded.
• Reinstall the cover.
Permanent wiring
connection
Ground Tab
Green
Ground
Screw
Black
Wire
Ground Wire
To avoid installation difficulties,
do not run the opener at this time.
White Wire
15
Black
Wire
The Protector System®
Information you'll need before you begin the installation of the safety reversing sensor.
The safety reversing sensor must be connected
and aligned correctly before the garage door
opener will move in the down direction. This is a
required safety device and cannot be disabled.
WARNING
Without a properly working safety reversing
sensor, persons (particularly children) could
be injured or killed by a closing garage door.
Read and follow all instructions.
To protect small children, install the safety
reversing sensor so that the beam will be no
higher than 4-6" above the garage floor.
Disconnect power to the garage door opener
before installing the safety reversing sensor.
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to
the receiving eye. The units can be installed on
either side of the garage door as long as the sun
never shines directly into the receiving eye lens.
Look at the label on the connector end of each case
to identify the sensors.
The brackets must be connected and fastened so
that the sending and receiving eyes face each other
as shown.
If an obstruction breaks the light beam while the
garage door is closing, the door will stop and
reverse to full open position and the opener light will
flash for 5 seconds.
The brackets must be securely fastened to a solid
surface such as the studs on either side of the door,
or add a piece of wood at each location if installing
in masonry construction.
The invisible light beam path must be unobstructed.
No part of the garage door (or door tracks, springs,
hinges, rollers or other hardware) can interrupt the
beam while the door is closing. If it does, use a
piece of wood to build out each sensor mounting
location to the minimum depth required for light
beam clearance.
Sensor Beam
4-6" max.
above floor
Sensor Beam
4-6" max.
above floor
Invisible Light Beam
Protection Area
Facing the door from inside the garage
16
Figure 1
Installation Step 10
Garage WALL or DOOR Track Installation
Install the Safety Reversing Sensor
(Receiving and Sending Eyes)
Mounting Bracket
With Square Holes
"C" Wrap
Figures 1, 2 and 3 show recommended assembly of
bracket(s) and "C" wrap based on the wall installation of
the sensors on each side of the garage door as shown
on page 16, or on the garage door tracks themselves.
Figures 4 amd 5 are variations which may fit your
installation requirements better. Make sure the wraps
and brackets are aligned so the sensors will face
each other across the garage door.
#10-32x3/8"
Screws
#10-32
Lock Nuts
Figure 2
Garage WALL Installation
1/4x1-1/2"
Lag Screws
1/4-20x1/2" Carriage Bolts
(with square shoulder)
Inside
Garage
Wall
Garage Wall or Door Track Installation
1. Fasten the "C" wraps to the mounting brackets having
square holes, using the hardware shown in Figure 1.
Garage Wall Installation
2. Connect each assembly to a slotted bracket, using
the hardware shown in Figure 2. Note alignment of
brackets for left and right sides of the door.
3. Finger tighten the lock nuts.
4. Use bracket mounting holes as a template to locate
and drill (2) 3/16" diameter pilot holes on both sides
of the garage door, 4"-6" above the floor but not
exceeding 6" (see warning on page 16).
5. Attach bracket assemblies with 1/4"x1-1/2" lag screws
as shown in Figure 2.
6. Adjust right and left side bracket assemblies to the
same distance out from mounting surface. Make
sure all door hardware obstructions are cleared.
Tighten the nuts securely.
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
"C" Wrap
1/4"-20
Lock Nuts
Figure 3
Garage DOOR Track Installation
1/4 " Lock Nuts
Inside
Garage
Wall
Garage
Door Track
Mounting Bracket
with Square Holes
Drill 3/8"
Holes
Garage Door Track Installation
Discard slotted bracket. Drill 3/8" holes in each track and
fasten securely with hardware as shown in Figure 3.
"C" Shaped
Wrap
1/4-20x1/2"
Carriage Bolts
Figure 4
Figure 5
Alternate Wall Mount
Alternate Floor Mount
Inside
Garage
Wall
Inside
Garage
Wall
Mounting Bracket
with Slot
Indicator Light
Mounting Bracket
with Square Holes
Mounting Bracket
with Square Holes
Mounting Bracket
with Slot
"C" Wrap
Sensor
with wire
Garage
Floor
Sensor with wire
Attach with
concrete anchors
(not provided)
"C" Wrap
Indicator Light
Garage
Floor
Hardware Shown Actual Size
#10-32x3/8"
Screw
#10x32
Lock Nut
1/4x1-1/2"
Lag Screw
Staples
17
1/4"-20x1/2"
Carriage Bolts
1/4"-20
Lock Nut
• Center each sensor unit in a "C" wrap with lenses
pointing toward each other across the door (see
Figure 6).
• Secure sensors with the hardware shown. Finger
tighten the wing nut on the receiving eye to allow
for final adjustment. Securely tighten the sending
eye wing nut.
• Run the wires from both sensors to the opener
(see Figure 7). Use insulated staples to secure the
wire to wall and ceiling.
• Strip 1/4" of insulation from each set of wires.
Separate white and white/black wires sufficiently to
connect to the opener terminal screws: white to 2
and white/black to 3.
Aligning the Safety Sensors
• Plug in the opener. Green indicator lights in both
the sending and receiving eyes will glow steadily if
wiring connections and alignment are correct.
The sending eye indicator light will glow regardless
of alignment or obstruction. If the indicator light is
off, dim, or flickering in the receiving eye (and the
invisible light beam path is not obstructed),
alignment is required.
• Loosen the sending eye wing nut and re-adjust,
aiming directly at the receiving eye. Lock in place.
• Loosen the receiving eye wing nut and adjust
sensor vertically and/or horizontally until it receives
the sender’s beam. When the green indicator light
glows steadily, tighten the wing nut.
Figure 6
"C" Wrap
Wing
Nut
Indicator
Light
Sensor
with Wire
1/4-20 x 1-1/2"
Hex Bolt
Trouble Shooting
1. If the sending eye indicator light does not glow
steadily after installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These
can occur under staples or at screw terminal
connections.
• Incorrect wiring between sensors and opener.
• An open wire (wire break).
2. If the sending eye indicator light glows steadily but
the receiving eye indicator light doesn't:
• Check alignment.
• Check for an open wire to the receiving eye.
3. If the receiving eye indicator light is dim, realign
either sensor.
NOTE: When the invisible beam path is obstructed or
misaligned while the door is closing, the door will
reverse. If the door is already open, it will not close.
The opener light will flash 10 times. (If bulb is not
installed, 10 clicks are audible.) See page 16.
Hardware Shown Actual Size
Figure 7
1/4-20x1-1/2"
Hex Bolt
Bell Wire
Connect Wire to
Opener Terminals
Wing Nut
Finished
Ceiling
Bell Wire
Sensor
Connections
Wall Control
Connections
(dotted line)
1
2
3
OPENER TERMINAL SCREWS
Sensor
Sensor
Invisible Light Beam
Protection Area
18
Installation Step 11
W
WARNING
Fasten Door Bracket & Plate
To prevent damage to steel, aluminum,
fiberglass or glass panel doors, always
reinforce the inside of the door both vertically
and horizontally with an angle iron.
INSTALLATION STEP 11
CAUTION
Fasten the Door Bracket
A horizontal reinforcement brace should be long
enough to be secured to two or three vertical
supports. A vertical reinforcement brace should
cover the height of the top panel.
Figure 1 shows one piece of angle iron as the
horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a U-shaped support.
The best solution is to check with your garage door
manufacturer for an opener installation door
reinforcement kit.
NOTE: Many door reinforcement kits provide for
direct attachment of the clevis pin and door arm. In
this case you will not need the door bracket; proceed
to Step 12.
Header
Bracket
AVERTISSEMENT
Door
Bracket
Location
ATTENTION
HORIZONTAL AND VERTICAL
REINFORCEMENT IS NEEDED
FOR LIGHTWEIGHT GARAGE
DOORS (FIBERGLASS,
ALUMINUM, STEEL, DOORS
WITH GLASS PANEL, ETC).
(NOT PROVIDED)
Vertical
Centerline
SECTIONAL DOORS
1. Center the door bracket on the previously marked
vertical centerline used for the header bracket
installation. Note correct UP placement, as
stamped inside the bracket.
2. Position the top edge of the bracket 2"-4" below
the top edge of the door, OR directly below any
structural support across the top of the door.
3. Mark, drill holes and install as follows, depending
on your door’s construction:
Figure 1
(Not Provided)
Vertical
Reinforcement
Vertical
Centerline
Vertical
Reinforcement
Bolt
5/16"-18x2"
Vertical
Centerline
UP
Metal or light weight doors using a vertical angle
iron brace between the door panel support and
the door bracket:
• Drill 3/16" fastening holes. Secure the door bracket
using the two 1/4"-14x5/8" self-threading screws.
(Figure 2A)
• Alternately, use two 5/16" bolts, lock washers and
nuts (not provided). (Figure 2B)
Door
Bracket
UP
Lock Washer
5/16"
Nut
5/16"-18
Door
Bracket
Self-Threading
Screw
1/4"-14x5/8"
Figure 2B
Figure 2A
(Not Provided)
Metal, insulated or light weight factory reinforced
doors:
• Drill 3/16" fastening holes. Secure the door bracket
using the self-threading screws (Figure 3).
Inside Edge
of Door or
Reinforcement Board
Bolt
5/16"x2"
UP
Vertical
Centerline
Wood Doors:
• Use top and bottom or side to side door bracket
holes. Drill 5/16" holes through the door and secure
bracket with 5/16"x2" carriage bolt, lock washer and
nuts (not provided). (Figure 4)
HARDWARE SHOWN
ACTUAL SIZE
NOTE: The 1/4"-14x5/8" selfthreading screws are not
intended for use on wood doors.
UP
Self-Threading
Screw
1/4"-14x5/8"
Figure 3
Self-Threading Screw
1/4"-14x5/8"
19
Vertical
Centerline
Figure 4
Installation Step 12
Connect Door Arm to Trolley
Make sure garage door is fully closed. Pull the manual release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away from the door) about 2” as shown in Figures 1,
2 and 3.
Figure 1:
• Fasten straight door arm section to outer trolley
with a clevis pin. Secure the connection with a ring
fastener.
• Fasten curved section to the door bracket in the
same way as shown.
Figure 2:
• Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
Inner Trolley
Outer Trolley
Clevis
Pin
Ring
Fastener
Rope
Lock
Washers
5/16"
Manual
Release
Handle
Nuts
5/16"-18
Door
Bracket
Straight
Door Arm
Screws
5/16"-18x7/8"
Curved
Door Arm
Clevis Pin
Figure 1
Figure 2
Door Bracket
Hole Alignment Alternative
Figure 3:
• If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 6" from
the solid end. Reconnect to trolley with cut end
down as shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
Lock
Washers
5/16"
Nuts
5/16"-18
Hardware Shown Actual Size
Screws
5/16"-18x7/8"
Nut 5/16"-18
Hex Screw
5/16"-18x7/8"
Lockwasher 5/16"
Ring Fastener
Cut This End
Figure 3
Clevis Pin
5/16" x1"
Proceed to Adjustment Step 1, page 21. Trolley will re-engage automatically when the opener is operated.
20
Adjustment Section: Pages 21 – 23
Adjustment Step 1
WARNING
Adjust the UP and DOWN Limits
Improper adjustment of the travel limits could
interfere with the proper operation of the
safety reverse system. The door might not
reverse properly when required and could
seriously injure or kill someone under it. Test
the safety reverse system following all
adjustments to the travel limits. See page 23.
Do not make any limit adjustments until the
Safety Reversing Sensors are completely
installed.
Limit adjustment settings regulate the points at
which the door will stop when moving up or down.
The door will stop in the up direction if anything
interferes with door travel. The door will reverse in
the down direction if anything interferes with the
door travel (including binding or unbalanced doors).
To operate the opener, press the Door Control push
button. Run the opener through a complete travel
cycle.
• Does the door open and close completely?
• Does the door stay closed and not reverse
unintentionally when fully closed?
If your door passes both of these tests, no limit
adjustments are necessary unless the reversing test
fails (see page 23).
2-4"
Cover
Protection
Bolt
Left Side
Panel
Adjustment procedures are outlined below. Run the
opener through a complete travel cycle after
each adjustment.
Repeated operation of the opener during adjustment
procedures may cause the motor to overheat and
shut off. Simply wait 15 minutes and try again.
Read the procedures carefully before proceeding to
Adjustment Step 2. Use a screwdriver to make limit
adjustments.
Limit
Adjustment
Screws
Adjustment Label
How and When to Adjust the Limits
• If the door does not open completely but opens
at least five feet:
Increase up travel. Turn the UP limit adjustment
screw clockwise. One turn equals 2" of travel.
NOTE: To prevent the trolley from hitting the
cover protection bolt, keep a minimum distance
of 2-4" between the trolley and the bolt.
• If door does not open at least 5 feet:
Adjust the UP (open) force as explained in
Adjustment Step 2.
• If the door does not close completely:
Increase down travel. Turn the DOWN limit
adjustment screw counterclockwise. One turn
equals 2" of travel.
If door still won't close completely and the trolley
bumps into the pulley bracket (see page 4), try
lengthening the door arm. (See page 20.)
If you have adjusted the door arm to the maximum
length and the door still will not close completely,
lower the header bracket. See Installation Steps 1
and 2, pages 8 and 9.
• If the opener reverses in fully closed position:
Decrease down travel. Turn the DOWN limit
adjustment screw clockwise. One turn equals 2"
of travel.
• If the door reverses when closing and there is
no visible interference to travel cycle:
If the opener light is flashing, the Safety Reversing
Sensors are either not installed, misaligned, or
obstructed. See Troubleshooting, page 18.
Test the door for binding: Pull the manual release
handle. Manually open and close the door. If the
door is binding, call for garage door service. If the
door is not binding or unbalanced, adjust the DOWN
(close) force. See Adjustment Step 2.
21
Adjustment Step 2
WARNING
Adjust the Force
Too much force on the door will interfere with
the proper operation of the safety reverse
system. The door might not reverse properly
when required and could seriously injure or
kill someone under it. Do not increase the
force beyond what is required to close the
door. Do not use the force adjustments to
compensate for a binding or sticking garage
door. Test the safety reverse system following
all adjustments to force levels. See page 23.
Force adjustment controls are located on the back
panel of the opener. Force adjustment settings
regulate the amount of power required to open and
close the door.
The door will stop in the up direction if anything
interferes with its travel. The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors).
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down
direction and stops in the up direction. Weather
conditions can affect the door movement, so
occasional adjustment may be needed.
The maximum force adjustment range is 260
degrees, about 3/4 of a complete turn. Do not force
controls beyond that point. Turn force adjustment
controls with a screwdriver.
Force Adjustment
Controls
1
9
1
7
3
2
3
9
9
1
7
1
7
3
9
1
7
3
5
5
KG
KG
3
5
5
KG
KG
Adjustment Label
Back Panel of Opener
How and When to Adjust the Forces
If the door doesn't open at least 5 feet
Increase UP (Open) force by turning the control
clockwise. Make 10 degree turn adjustments until
door opens completely. Re-adjust the UP limit if
necessary. After each adjustment, run the opener
through a complete travel cycle.
Test the DOWN (close) force
Grasp the door bottom when the door is about
halfway through DOWN (close) travel. The door
should reverse. Reversal halfway through down
travel does not guarantee reversal on a one-inch
obstruction. See page 23. If the door is hard to
hold or doesn't reverse, decrease the DOWN
(close) force by turning the control
counterclockwise.
Make 10 degree turn adjustments until the door
reverses normally. After each adjustment, run the
opener through a complete cycle.
If the door reverses during the down (close) cycle
and the opener lights aren't flashing
Increase DOWN (close) force by turning the control
clockwise. Make 10 degree turn adjustments until the
door completes a close cycle. After each adjustment,
run the opener through a complete travel cycle. Do
not increase the force beyond the minimum
amount required to close the door.
Test the UP (open) force
Grasp the door bottom when the door is about
halfway through UP (open) travel. The door should
stop. If the door is hard to hold or doesn't stop,
decrease UP (open) force by turning the control
counterclockwise.
Make 10 degree turn adjustments until the door
stops easily. After each adjustment, run the opener
through a complete travel cycle.
22
Adjustment Step 3
WARNING
Test The Protector System®
Without a properly working safety reversing
sensor, persons (particularly children) could
be seriously injured or killed if trapped by a
closing garage door. Repeat this test once a
month.
• Press the Door Control push button to open the
door.
• Place the opener carton in the path of the door.
• Press the Door Control push button to close the
door. The door will not move more than an inch,
and the opener light will flash.
Professional service is required if the opener
closes the door when the safety reversing
sensor is obstructed.
The garage door opener will not close from a
remote control transmitter if the indicator light
in either sensor is off (alerting you to the fact
that the sensor is misaligned or obstructed).
The garage door can be closed by pressing and
holding the Door Control push button until down
travel is completed.
Safety Reversing Sensor
Adjustment Step 4
Safety Reversing Sensor
WARNING
Test the Safety Reverse System
Failure to test and adjust the safety reverse
system may result in serious injury or death to
persons trapped by a closing garage door.
Repeat this test once a month and adjust as
needed.
Test:
• Place a 2x4 laid flat on the floor, centered under
the garage door.
• Operate the door in the down direction. The door
must reverse on striking the obstruction.
Adjustment:
If the door stops on the obstruction, it is not traveling
far enough in the down direction.
• Increase the DOWN limit by turning the DOWN
limit adjustment screw counterclockwise 1/4 turn.
• Repeat the test.
Make sure limit adjustments do not force the
door arm beyond a straight up and down
position. See the illustration on page 20.
• When the door reverses on the 2x4, remove the
obstruction and run the opener through 3 or 4
complete travel cycles to test adjustment.
If the door will not reverse after repeated
adjustment attempts, call for professional
garage door service.
GARAGE DOOR
Important safety check
Repeat Adjustment Steps 1, 2 and 4 after:
• Each adjustment of door arm length, force controls
or limit controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
2x4 Laid Flat
23
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Do not permit children either to operate or to play with the opener. Keep a remote control in a
location inaccessible to children.
3. Operate opener only when the door is in full view and free from any obstruction. Keep the door in
sight until it is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
4. Check safety reversal system monthly. See page 23. The garage door MUST reverse on contact
with a one-inch object (or a 2x4 board laid flat) placed on the floor. If an adjustment is made to
either the force or the limit of travel, both adjustments may be needed and the safety reversal
system must be checked. Failure to properly adjust the opener may result in severe injury or death.
5. If possible, use the manual release only when the door is in a closed position. Caution should be
taken whenever the disconnect cord is actuated with the door open. Weak or broken springs may
cause the door to fall rapidly, causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY BALANCED. See page 3. An improperly balanced door may not
reverse when required and could result in severe injury or death. Repairs to cables, spring
assemblies and other hardware must be made by a professional garage door person.
7. Disconnect the electric power from the garage door opener before making any repairs or removing
the covers.
8.
SAVE THESE INSTRUCTIONS.
Do not exceed 8 complete cycles of door operation per hour in commercial applications.
Care of Your Opener
Limit and Force Adjustment Control
Limit Controls
Force Controls
9
1
7
Adjustment Label
(Located on the left side panel)
3
9
1
7
3
5
5
KG
KG
Adjustment Label
(Located on the back panel)
Weather conditions may cause some minor
changes in door operation requiring some
re-adjustments, particularly during the first
year of operation.
Pages 21 and 22 refer to the limit and force
adjustments. Only a screwdriver is required.
Follow the instructions carefully.
Repeat the safety reverse test (page 23) after
any adjustment of limits or force.
24
Operation of Your Opener
Activate the opener with any of the following:
• The Door Control. Hold push button down until the
door starts to move.
• A Remote Control Transmitter. Hold push button
down until the door starts to move.
• The Outside Keylock or Keyless Entry.
(See Accessories)
WARNING
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible, use the manual release rope
and handle only when the door is fully closed.
When the opener is activated with the safety
reversing sensor installed and correctly aligned:
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle,
and the opener light will blink for 5 seconds, when
the invisible beam is broken. If fully open, the door
will not close when the beam is broken. The
sensor has no effect in the opening cycle.
Trolley
Release
Arm
Trolley
Manual Release
Handle (Pull Down)
NO
TIC
E
To open the door
manually: The door
should be fully closed if
possible. Pull down on
the red manual release
handle and lift the door
manually. To reconnect
the door to the opener,
press the Door Control
push button.
Manual disconnect
position
If the sensor is not installed, or is not aligned
correctly, the door won't close from any remote
control transmitter. However, you can close the door
with the Door Control, the Outside Keylock, or
Keyless Entry, if you activate them until down travel
is complete. If you release them too soon, the door
will reverse.
The opener light will turn on under the following
conditions: When the opener is initially plugged in;
when the power is interrupted, when the opener is
activated, and when someone walks through the
open garage door. It will turn off automatically after
4-1/2 minutes. Bulb size is 75 watts maximum.
Trolley
Manual Release Handle
(Pull Down & Back
Towards Opener)
Trolley
Release
Arm
NOTICE
Lockout position
Operation of the
Door Control Button
Press to open or close the door.
Press again to reverse the door during the closing
cycle or to stop the door while it’s opening.
25
The lockout feature
prevents the trolley from
reconnecting automatically. Pull the
manual release handle
down and back (toward
the opener). The door
can then be raised and
lowered manually as
often as necessary. To
disengage the lockout
feature, pull the manual
release handle straight
down. The trolley will
reconnect on the next
UP or DOWN operation.
SECURITY✚ 3-Channel Remote Control Programming (OPTIONAL)
NOTICE: To comply with FCC/IC rules, adjustment or modifications of this receiver
and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
WARNING
The 90 Series remote control (with yellow battery test
light) works only with door openers and light controls
having an orange “Smart” button and a yellow indicator
light.
Programming instructions are described and illustrated
below. The additional push buttons can also activate
other garage door openers and/or light controls.
(Instructions for programming light products are included
with those accessories.) See Accessories on page 34.
Your SECURITY✚ opener will operate with:
• several SECURITY✚ remote controls (with yellow
indicator lights) utilizing up to 8 functions. NOTE:
Open/Close/Stop operation counts as 1 function.
• one Keyless Entry System (with SECURITY✚ logo)
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death. Do not allow children
to operate the Door Control or remote control
transmitter(s).
A moving garage door could injure or kill
someone under it. Activate the opener only
when you can see the door clearly, it is free of
obstructions, and is properly adjusted.
Model 96LM
SECURITY✚ Remote Control
Yellow
Battery Indicator
Light
To Program the Opener to Accept
the Remote Control Code
Select a remote control push button to operate the
opener. The large button is recommended for use with
a garage door opener.
1. Press and hold the selected remote control push
button. See Figure 1.
2. Press and release the “Smart” (learn) button on the
opener panel, Figure 2. The indicator light on the
panel will begin to blink and the opener light will
flash once.
3. Release the remote push button.
Now the opener will operate when that remote control
button is pressed. Test it by pressing the remote button
to see that the door goes up and down.
Figure 1
Select a
push button
SECURITY✚
Garage Door Opener
1
9
Figure 2
1
7
9
3
1
7
3
5
5
KG
KG
"Smart" (learn)
Indicator Light
Button
BACK PANEL
Adding a remote can also be done from the MultiFunction Door Control, as follows:
1. With the door closed, press and hold a remote push
button.
2. Press and hold the Light button on the door control.
3. Press and hold the door control push bar.
4. After the opener light flashes, release all buttons.
Test by pressing the remote push button.
Code programming instructions are
also located on the opener panel.
Open/Close/Stop Operation
The SECURITY✚ remote control can be programmed
to operate one door using all 3 buttons: the large
button will only open the door, the middle button will
only close the door, and the third button will stop the
door’s movement. You may set up this feature as
follows:
1. With the door closed, press and hold
the large remote push button.
Open
2. Press and hold the Lock button
Close
Stop
on the door control.
3. Press and hold the door control push bar.
When the opener light flashes, release all buttons. Test
by pressing the large (Open) button on the remote.
The door should open. Press it again while the door is
open and nothing should happen. Press the middle
(Close) button and the door should close. Press the
third (Stop) button while the door is moving and it
should stop immediately.
To Erase All Remote Control Codes
Press and hold the “Smart” button on the opener panel
until the indicator light turns off (about 6 seconds). All
transmitter codes are now erased. Then follow the
steps above to re-program each remote control.
To Control the Opener Light
With SECURITY✚ transmitters, a remote push button
can be programmed to operate the opener light without
opening the door.
1. With the door closed, press and hold the remote
button that you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener light flashes, release all buttons.
Test by pressing the remote push button. The opener
light should turn on or off but the door should not move.
3
2
26
SECURITY✚ Multi-Function Door Control - Model 58LM (OPTIONAL)
NOTICE: To ensure the proper functioning of your new
Garage Door Opener, please remove all old or previous
push buttons/door control panels.
WARNING
Children operating or playing with a garage door
opener can injure themselves or others. The garage
door could close and cause serious injury or death.
Install the door control (or any additional push
buttons) out of the reach of children and away from
all moving parts of the door and door hardware, but
where the garage door is visible. Do not allow
children to operate the push button(s) or the remote
control transmitter(s).
A moving garage door could injure someone under
it. Activate the opener only when the door is
properly adjusted, you can see it clearly, and there
are no obstructions to door travel.
• Strip 1/4" of insulation from one end of the bell wire;
connect the wire to the two screw terminals on the
back of the door control panel as follows: white to 2
and white/red to 1. (NOTE: If “Lock” and “Light”
buttons do not function after completing
installation, reverse the connections.)
• Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all
moving parts of the door and door hardware.
Fasten the Door Control Panel securely with
6ABx1" screws. If installing into drywall, drill 5/32"
holes and use the anchors provided.
• Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.
• Connect the bell wire to the opener terminal screws
as follows: white to 2 and white/red to 1.
Multi-Function
Door Control Panel
Terminal Screws
-1
Opener
Terminal
Screws
2-Conductor
Bell Wire
-2
RED-1
1
WHT-2
BLK-3
2
3
Lock Button
2-Conductor
Bell Wire
9
1
7
3
9
1
7
3
5
5
KG
KG
LOCK
LIGHT
Light Button
Door Control
Push Bar
Back Panel
of Opener
Antenna
Multi-Function
Door Control Panel
Operation of the Multi-Function Door Control Panel
The Door Control Push Bar: Press to open or close
the door. Press again to reverse the door during the
closing cycle or to stop the door while it's opening.
Lock Feature: Designed to prevent operation of the
door from portable remote controls. However, the
door will open and close from the Door Control push
bar and from the Keylock and the Keyless Entry
Accessories.
To Activate: Press and hold the Lock button for
2 seconds. The push bar indicator light will flash as
long as the Lock is on.
To Turn Off: Press and hold the Lock button again
for 2 seconds. The indicator light will stop flashing.
Normal operation will resume. The Lock feature will
also turn off whenever the "Smart" button on the
opener end panel is activated.
Light Feature: Press the Light button. If the opener
light is off, it will turn on.
If the opener light is on, (even in the 4-1/2 minute
automatic cycle) it will turn off.
But if you use the Light button to turn the light on
and then activate the opener, the light will turn off
after 4-1/2 minutes.
The Light Feature will not turn the opener light off
when the door is in motion.
27
SECURITY✚ Multi-Function Door Control - Model 68LM (OPTIONAL)
NOTE: To ensure the proper functioning of your
new Garage Door Opener, remove all old or
previous push buttons/door control panels.
WARNING
DO NOT CONNECT TO LIVE ELECTRICAL WIRING.
CONNECT ONLY TO 24 VOLT LOW VOLTAGE
WIRES. CONNECTION TO LIVE WIRES OR
HIGHER VOLTAGE MAY CAUSE SERIOUS INJURY
FROM SHOCK, BURN OR ELECTROCUTION.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause serious
injury or death.
Install the door control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control transmitter(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it clearly,
and there are no obstructions to door travel.
Locate the door control within sight of the door at
a minimum height of 5 feet where small children
cannot reach, and away from all moving parts of
the door and door hardware.
The multi-function door control panel is typically
attached directly to the wall, Figure 1. For pre-wired
installations (as in new home construction) it can be
mounted to a standard single gang box, Figure 2.
• Strip 1/4" of insulation from one end of the bell wire;
connect the wire to the two screw terminals on the
back of the door control panel as follows: white to 2
and white/red to 1. (NOTE: If “Lock” and “Light”
buttons do not function after completing
installation, reverse the connections.)
• For standard wall mount, fasten the door control
panel securely with 6ABx1-1/4" self-tapping screws.
Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.
• For pre-wired installations, mount the door control
to the gang box with the 6-32x1" machine screws
provided.
• Connect the bell wire to the opener terminal screws
as follows: white to 2 and white/red to 1.
24 Volt
2-Conductor
Bell Wire
Figure 2
LOCK
LIGHT
Alternate Installation
Opener
Terminal
Screws
Figure 1
Standard Installation
2-Conductor
Bell Wire
RED-1
1
WHT-2
BLK-3
2
3
9
1
RED
1
7
2
WHITE
Lock
Button
9
3
1
7
3
5
5
KG
KG
Light Button
LOCK
LIGHT
Door Control
Push Bar
Back Panel
of Opener
Multi-Function
Door Control Panel
Terminal Screws
Antenna
Operation of the Multi-Function Door Control Panel
The Door Control Push Bar: Press to open or
close the door. Press again to reverse the door
during the closing cycle or to stop the door while
it's opening.
Light Feature: Press the Light button. If the opener
light is off, it will turn on.
If the opener light is on, (even in the 4-1/2 minute
automatic cycle) it will turn off.
But if you use the Light button to turn the light on
and then activate the opener, the light will turn off
after 4-1/2 minutes.
The Light Feature will not turn the opener light off
when the door is in motion.
Lock Feature: Designed to prevent operation of the
door from portable remote controls. However, the
door will open and close from the Door Control push
bar and from the Keylock and the Keyless Entry
Accessories.
To Activate: Press and hold the Lock button for
2 seconds. The push bar indicator light will flash as
long as the Lock is on.
To Turn Off: Press and hold the Lock button again
for 2 seconds. The indicator light will stop flashing.
Normal operation will resume. The Lock feature will
also turn off whenever the “Smart" button on the
opener end panel is activated.
28
SECURITY✚ Keyless Entry - Model 67LM (OPTIONAL)
To comply with FCC/IC rules, adjustment or modification of receiver and/or transmitter
is prohibited, except for changing the code setting and replacing the transmitter battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
WARNING
Children operating or playing with a garage door
opener can injure themselves or others. The garage
door could close and cause serious injury or death.
Do not allow children to operate the door push
button(s) or remote control(s).
A moving garage door could injure or kill someone
under it. Activate the opener only when you can see
the door clearly, it is free of obstructions, and is
properly adjusted.
Features
For use with any SECURITY✚ compatible garage door
opener receiver.
Personalized Code: Up to 10,000 possible
combinations. Code can be easily changed if desired.
Operation: 12 Volt power supply. Opener activates
when 4-digit code and Enter button is pressed.
If wrong numbers are accidentally pressed, correction
can be made immediately. The Enter button will transmit
only the last four digits.
The Keypad will blink for 15 seconds after the code is
transmitted. During that time the Enter button can be
used to stop or reverse the door travel.
A temporary entry code can be added for visitors or
service persons. This temporary code can be limited to a
programmable number of hours or a programmable
number of entries.
Installation
Typical
Keypad
Sectional Door
Choose a
Installation
convenient
Exterior Front Wall
location for
1-Piece or
installation. It
Sectional Door
should be at eye
level, reachable
Door Jamb Edge
(Optional Location
by the shortest
for 1-Piece Door)
person who will
Door Jamb Face
use it, and within
SECTIONAL DOOR ONLY
sight of the door.
KEYPAD MUST BE INSTALLED
For a one-piece
WITHIN SIGHT OF THE DOOR
door, choose the
optional location shown in
the illustration to avoid injury
Plug
as the door swings out.
Open the keypad cover and
remove the battery
compartment screw and
cover. Take out the battery.
Hold keypad firmly with the
cover half open so both top
and bottom mounting holes
Battery
Battery
are visible. Use a punch to
Cover
mark each hole. Drill two
1/8" pilot holes. Fasten securely with screws provided.
Insert the plug provided into the top hole to cover the
fastening screw. Reinstall the battery, matching the +
and – markings on the battery compartment. Refasten
the compartment cover.
Setting the Personal Entry Code
We recommend that you program your personal
code now, before you install the Keyless Entry.
Then you can test the reception at the mounting
location before you proceed further.
1.Choose a 4-digit personal entry code using the
numbers from 0 to 9 (a number can be used more
than once, for example, 4,0, 4,1.)
2. Press the four buttons for the code, then press and
hold the Enter button. The indicator light on the
door opener panel will blink.
3. Press and release the “Smart” button on the door
opener panel. After the opener light blinks, release
the Enter button.
Test by pressing the the code, then press Enter. The
door should begin to move.
You may also program the Keyless Entry from the
Multi-Function Door Control, as follows:
1.With the door closed, enter the four digit code
desired, then press and hold Enter.
2. Press and hold the light button on the door control.
3. Press and hold the door control push bar.
4. After the opener light blinks, release all buttons.
Changing the Personal Entry Code
Press the four buttons for the present personal entry
code, then press and hold the 0 button, then press
Enter.
The opener light will blink twice. Release the buttons.
Press the new 4-digit code you have chosen, then
press Enter.
The opener light will blink once when the code has
been learned.
Test by pressing the new code, then press Enter. The
door should move.
Garage Door Opener Receiver
(With Smart Button)
1
2
3
9
1
9
1
C
AB
2
I
1
GH
7
4
F
DE
O
3
MN
L
JK
6
3
7
3
5
5
KG
KG
V
5
TU
8
S
PR
7
0
Y
WX
9
R
TE
EN
Smart
Button
Indicator
Light
29
Having a Problem?
Situation
Probable Cause & Solution
The opener doesn't
operate from either
the Door Control or
the remote control:
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,
check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.)
2. Have you disabled all door locks? Review installation instruction warnings on page 7.
3. Is there a build-up of ice or snow under the door? The door may be frozen to the
ground. Remove any restriction.
4. The garage door spring may be broken. Have it replaced.
5. Repeated operation may have tripped the overload protector in the motor. Wait 15
minutes. Try again.
Opener operates
from the remote, but
not from Door
Control:
1. Is the door control lit? If not, remove the bell wire from the opener terminals. Short
the red and white terminals by touching both terminals at the same time with a piece
of wire. If the opener runs, check for a faulty wire connection at the door control, a
short under the staples, or a broken wire.
2. Are the wiring connections correct? Review Step 6, page 13.
The door operates
from the Door
Control, but not from
the remote control:
1. Is the door push button flashing? If your model has the Lock feature, turn it off.
2. Your opener needs to re-learn a remote control code. Refer to instructions on the
opener panel.
3. Does the battery test light glow when the remote control push button is pressed? If not,
replace the battery.
4. Program the receiver to match the remote control code.
5. Repeat the receiver programming procedure with all remote controls.
The remote control
has short range:
1. Check the battery test light. If the light is dim, replace the battery.
2. Change the location of the remote control in your car.
3. Check to be sure the antenna on the side or back panel of opener extends fully
downward. Install Antenna Kit, Part No. 41A3504, to increase range.
4. Some installations may have shorter range due to a metal door, foil backed
insulation, or metal garage siding.
Opener noise is
disturbing in living
quarters of home:
If operational noise is a problem because of proximity of the opener to the living
quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to
minimize vibration to the house and is easy to install.
The garage door
opens and closes
by itself:
1. Be sure that all remote control push buttons and battery indicator lights are off.
2. Remove the bell wire from the door control terminals and operate from the remote
only. If this solves the problem, the door control is faulty (replace), or there is an
intermittent short on the wire between the door control and the opener.
3. Clear memory and reprogram all remote controls.
The door doesn't
open completely:
1. If the door has been working properly but now doesn't open all the way, increase the
up force. See page 22.
2. Is something obstructing the door? Remove the obstruction or repair the door.
3. If door opens at least 5 feet, the travel limits may need to be increased. One turn
equals 2 inches of travel. See page 21.
Repeat the safety reverse test after the adjustment is complete.
The door stops but
doesn't close
completely:
Review the travel limits adjustment procedures on page 21.
Repeat the safety reverse test after any adjustment of door arm length, close
force or down limit.
30
Having a Problem? (continued)
Situation
Probable Cause & Solution
The door opens but
won't close:
1. If the opener light blinks, check the safety reversing sensor. See page 18.
2. If the opener light does not blink and it is a new installation, check the down force.
See Adjustment Step 2, page 22. For an existing installation, see below.
Repeat the safety reverse test after the adjustment is complete.
The door reverses for
no apparent reason
and opener light
doesn't blink:
1. Is something obstructing the door? Pull the manual release handle. Operate the door
manually. If it is unbalanced or binding, call for professional garage door service.
2. Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 22.
4. If door reverses in the fully closed position, decrease the travel limits (page 21).
Repeat safety reverse test after adjustments to force or travel limits. The need
for occasional adjustment of the force and limit settings is normal. Weather
conditions in particular can affect door travel.
The door reverses for
no apparent reason
and opener light
blinks for 5 seconds
after reversing:
Check the safety reversing sensor. Remove any obstruction or align the receiving eye.
See page 18.
The opener light:
. . . doesn't turn on:
Replace the light bulb (75 watts maximum). Use a standard neck garage door opener
bulb if regular bulb burns out.
. . . doesn't turn off:
Is the Light feature on? Turn it off.
The opener strains
or maximum force is
needed to operate
door:
The door may be out of balance or the springs are broken. Close the door and use the
manual release to disconnect the trolley. Open and close the door manually. A properly
balanced door will stay in any point of travel while being supported entirely by its springs. If it
does not, disconnect the opener and call a professional garage door serviceman.
Do not increase the force to operate the opener.
The opener motor
hums briefly, then
won't work:
1. The garage door springs are broken. See above.
2. If the problem occurs on the first operation of the opener, door may be locked. Disable
the door lock. If the chain was removed and reinstalled, the motor may be out of phase.
Remove the chain; cycle the motor to the down position. Observe the drive sprocket.
When it turns in a clockwise direction and stops in the down position, reinstall the chain.
Repeat the safety reverse test after the adjustment is complete.
The opener won't
operate due to
power failure:
1. Use the manual release to disconnect the trolley. The door can be opened and closed
manually. When the power is restored, press the Door Control push button and trolley will
automatically reconnect (unless trolley is in lockout position.) See page 25.
2. The Outside Quick Release accessory (for use on garages with no service door)
disconnects the trolley from outside the garage in case of power failure.
The chain droops
or sags:
It is normal for the chain to droop slightly in the closed door position. Use the manual
release rope and handle to disconnect the trolley. If the chain returns to the normal
height when the trolley is disengaged and the door reverses on a 2x4 laid flat, no
adjustments are needed. (See page 7.)
31
Repair Parts
Rail Assembly Parts
3
1
4
E
AS
RE
IL G 3A4
.8
NO
RA
2
5
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
1A995
41A2780
41A3489
CD1008
CD1010
CD1012
83A4
Master link kit
Chain pulley bracket
Complete trolley assembly
8 Foot Rail Assembly
10 Foot Rail Assembly
12 Foot Rail Assembly
Rail grease
5
Installation Parts
3
2
6
4
1
5
NLY
TO
UN
G
LIN
MO
CEI
UP
NOT
ICE
KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
PART
NO.
41A4166
217A238
41A2828
12B374
12B380
41A4353
41A4373A
178B35
12B483
178B34
12B484
12B485
41A3535
41A4116
114A2296
DESCRIPTION
7
Door control push button
2-conductor bell wire, white & white/red
Manual rope & handle assembly
Door bracket
Door bracket plate
Header bracket w/clevis pin & fastener
Safety sensor kit
(receiving and sending eyes)
with 3' 2-conductor bell wire attached
Curved door arm section
C Wrap bracket
Straight door arm section
Square hole mounting bracket
Slotted mounting bracket
NOT SHOWN
Installation hardware bag (see page 5).
Safety sensor hardware
Owner's manual
32
9
8
11
12
10
Repair Parts
Opener Assembly Parts
1
2
3
4
15
18
7
18
17
15
5
12
14
LIMIT SWITCH ASSY.
(Down)
Contact
8
9
16
6
10
13
Brown
Wire
Grey
Wire
DN
UP
Drive
Gear
Center Limit
Contact
KEY
NO.
PART
NO.
1
2
3
41C5069
144B18
41C4470
4
41A2817
5
6
7
8
9
143D146
175B88M
30B432
12A461
41A3150
(Up)
Contact
Yellow
Wire
11
DESCRIPTION
Rail support bracket assembly kit
Pulley (Chain)
Gear and sprocket assy.
Complete with:
Spring washer
Thrust washer
Retaining washer
Bearing plate
Roll pins (2)
Drive gear and worm gear
Helical gear w/retainer and grease
Sprocket shaft plate with screws
Drive/worm gear kit w/grease
Roll pins (2)
Front end panel
Light socket
Capacitor
Capacitor bracket
Terminal block with screws
KEY
NO.
PART
NO.
10
41D4509
11
12
13
14
15
16
17
18
33
DESCRIPTION
Replacement motor & bracket
assembly
Complete with: Motor, worm,
bracket, bearing assembly
41A4475
Cover
41A2818
Helical gear & retainer w/grease
41D3452
Limit switch assembly
41C4398A
RPM sensor assembly
41C4246
Wire harness assembly w/plug
41A2826
Shaft bearing kit
41A2822A
Interruptor cup assembly
41A5021-1CATS Receiver logic board assembly
Complete with: Logic board, end
panel with all labels
NOT SHOWN
41A2825
Opener assembly hardware kit
(includes screws not designated
by a number in illustration).
Accessories Available for your Opener
Model 81LM
“Smart” Remote Control:
Includes visor clip.
Model 972LM
SECURITY✚ 2-Channel
Remote Control:
Includes visor clip.
Model 971LM
SECURITY✚ Single-Function
Remote Control:
Includes visor clip.
Model 973LM
SECURITY✚ 3-Channel
Remote Control:
Includes visor clip.
Model 58LM
Multi-Function Door Control Panel:
Provides a Lock Feature which
prevents operation of garage door
opener from portable remotes and
a Light Feature for constant light.
Model 970LM
SECURITY✚ 3-Channel Mini
Remote Control:
With key ring and Velco fastening
strip.
Multi-Function Door Control Panel:
For pre-wired installation to a
standard single gang box, or
mounted directly to the wall.
Features same as 58LM.
Model 976LM
SECURITY✚ Keyless Entry:
Enables homeowner to operate garage
door opener from outside by entering
code on specially designed keyboard.
Also can add a temporary pass code
for visitors or service persons. This
temporary code can be limited to a
programmable number of hours or
entries.
Model CD1008 8 foot Complete Rail and
Chain Assembly:
To allow an 8 foot door to open fully.
Model 1702
Outside Quick Release:
Required for a garage with NO
access door.
Model CD1010 10 foot Complete Rail and
Chain Assembly:
To allow a 10 foot door to open fully.
Model 59
Outside Keylock:
Opens the garage door
automatically from outside when
remote control is not handy.
Model CD1012 12 foot Complete Rail and
Chain Assembly:
To allow a 12 foot door to open fully.
180C139
NEMA 1 Push Button:
Heavy Duty Door Control Push
Button (one button).
LOCK
LIGHT
Model 68LM
LOCK
LIGHT
Other Products For Your Opener
108D36
Light Lens Cover:
Attractive lens cover protects light
bulbs and diffuses light to every
corner of your garage.
34
Index
Access Door/Outside Quick Release Accessory..........................................................................................4, 34
Chain Tension ..............................................................................................................................................4, 7, 31
Electrical Safety Warnings....................................................................................................................2, 7, 15, 24
Garage Door
Testing for balance, binding and sticking.............................................................................................3, 21, 22, 24
Determining high point of travel: ............................................................................................................................8
Disabling existing locks......................................................................................................................................3, 7
Force Controls
Adjustment procedures.....................................................................................................................................22
Problems that might require force adjustments ..........................................................................................30, 31
Safety warnings ..........................................................................................................................................22, 24
Door hardware .........................................................................................................................3, 4, 7, 8, 13, 24, 25
Maintenance Instruction Label.........................................................................................................................7, 13
Reinforcement requirements ...........................................................................................................................4, 19
Removing all ropes ............................................................................................................................................3, 7
Possible door damage .........................................................................................................................3, 11, 19, 25
Travel Limits
Adjustment Procedures ....................................................................................................................................21
Problems that might require Limit adjustments...........................................................................................30, 31
Safety Warnings .........................................................................................................................................21, 24
Manual Release Rope & Handle
Lockout Feature..................................................................................................................................................25
Manual Disconnect .......................................................................................................................................25, 31
Safety Warnings .................................................................................................................................7, 12, 24, 25
Opener Terminals
Door Control Connections ..................................................................................................................................13
Safety Reversing Sensor Connections ...............................................................................................................18
Outside Keylock Accessory Connections ...........................................................................................................13
Operational Noise
Sprocket noise ......................................................................................................................................................7
Vibration noise (isolator kit) ................................................................................................................................26
Operation of Optional Accessories
Model 96LM Remote Control..............................................................................................................................26
Model 58LM Door Control...................................................................................................................................27
Model 68LM Door Control...................................................................................................................................28
Model 67LM Keyless Entry .................................................................................................................................29
Protector System® ..........................................................................................................................................16, 23
Safety Reverse Test Procedure..........................................................................................................................23
Testing required............................................................................................................................7, 23, 24, 30, 31
Safety Reverse System Problems
Securing header bracket to wall .......................................................................................................................8, 9
Adjusting travel limits ..........................................................................................................................................21
Applying excessive force on the door .................................................................................................................22
Buckling or uneven floor .....................................................................................................................................23
Safety Warnings.................................................................2, 6, 7, 8, 11, 12, 13, 14, 15, 16, 19, 21, 22, 23, 24, 25
User Instruction Label for garage wall ..........................................................................................................7, 13
35
LIFTMASTER SERVICE IS
ON CALL
OUR LARGE SERVICE ORGANIZATION
SPANS AMERICA AND NORTH AMERICA
INSTALLATION AND SERVICE INFORMATION IS AS
NEAR AS YOUR TELEPHONE SIX DAYS A WEEK.
SIMPLY DIAL OUR TOLL FREE NUMBER:
HOW TO ORDER
REPAIR PARTS
Selling prices will be furnished on request or parts will
be shipped at prevailing prices and you will be billed
accordingly.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE
THE FOLLOWING INFORMATION:
• PART NUMBER
• PART NAME
1-800-528-2806
HOURS: (Mountain Std. Time)
6:00 A.M. TO 6:00 P.M. - Monday through Friday
7:00 A.M. TO 3:00 P.M. - Saturday
Closed Sunday
www.liftmaster.com
For professional installation, parts and service,
contact your local LIFTMASTER/ CHAMBERLAIN
dealer. Look for him in the Yellow Pages, or call our
Service number for a list of dealers in your area.
• MODEL NUMBER
ADDRESS ORDERS TO:
THE CHAMBERLAIN GROUP, INC.
Technical Support Group
6020 S. Country Club Rd.
Tucson, Arizona 85706
SERVICE INFORMATION
TOLL FREE NUMBER:
1-800-528-2806
LIFTMASTER GARAGE DOOR OPENER ONE-YEAR LIMITED WARRANTY
Chamberlain/LiftMaster warrants to the first retail purchaser of this product that it will be free from any defect in materials and/or
workmanship for a period of twelve full months from the date of purchase. The product must be used in complete accordance with
Lift-Master's instructions for installation, operation and care.
LIMITED WARRANTY ON MOTOR
Model ATS 211R: The motor is warranteed to be free from any defect in materials and/or workmanship for a period of 12 full months
(1 year) from the date of purchase.
This warranty does not cover non-defect damage, damage caused by unreasonable use (including abuse, failure to provide
reasonable and necessary maintenance, or any alterations to the product), labor charges for dismantling or reinstalling of a repaired
or replaced unit or replacement batteries.
If, during the warranty period, the product appears as though it may be defective, CALL OUR TOLL FREE SERVICE NUMBER
BEFORE DISMANTLING IT (1-800-528-2806). If the product is then alleged to be defective, please send it pre-paid and insured to
our Service Center to obtain warranty repair. You will be advised of shipping instructions when you call the number listed above.
Please be sure to include a brief description of the problem and a dated proof-of-purchase receipt with any product that is returned for
warranty repair.
Product under warranty, which upon receipt by Chamberlain/LiftMaster is determined to be defective in materials and/or workmanship,
will be repaired or replaced (Chamberlain's option) at no cost to you and returned pre-paid. Defective parts will be repaired or
replaced with new or factory rebuild parts at Chamberlain's option.
THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IS
LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. SOME STATES MAY NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
All claims for consequential or incidental damages for breach of this warranty are excluded and in no event shall manufacturer's
liability for breach of warranty, negligence, strict liability or breach of contract exceed the cost of the product covered herein, but the
purchaser is entitled to the remedies expressly provided in this policy. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
No representative or person is authorized to assume for us any other liability in connection with the sale of this product. This warranty
gives you specific legal rights, and you may also have other rights which may vary from state to state.
114A2296B
© 2001, The Chamberlain Group, Inc.
All Rights Reserved
Printed in Mexico
Download PDF

advertising