CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling (800) 840-
0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized service center.
500-181 rev A
How IR repeating works Specifications (typical)
The IR receiver is wired to the IR hub which routes the signal to IR emitters
Exp sio n
Pw r
IR
Receiver
Zon e
Model
P-1205
C HANNEL
TM
V
Glo ba
IR
Re cei ver Emitters
+1
2D C mA
250
Tx at
Pl ay op
St
FF
>>
Pa us ew
<<
Le ar
2
1 5
3
6
9
4
7 w er
8
0
-/-
Vo
Le ar
Er ro
O
O
Sa ct
Se le
Tu ne
VC
VD
TV
Point an
IR remote control at the IR receiver
And the emitter CD player repeats the IR signal in the other room.
Be sure the emitter is attached directly over the component’s IR receiver. To locate the IR receiver, shine a flashlight into the unit and look for the sensor.
Voltage requirements:
IR Freq. range supported:
IR pickup range:
Mounting requirements:
Color:
8 - 12 VDC
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
Single-gang box or ring
White
Specifications subject to change without notice.
IR-2005
(rear view)
The IR-2005 includes these items:
Screwless decorator style trim ring
Single-gang decorator style IR wall plate
IR-2400 Plasma proof IR receiver
IR receiver window
!
!
Features:
!
Plasma Proof IR receiver
Status LEDs for IR signal indication
Mounts in a single-gang box or low-voltage ring
IR-2005
(front view)
Single Room IR Setup
IR-2005
(rear view)
A single room IR system can be created by connecting the IR-
2005 with the P-1205. Connect the three screw terminals on the P-1205 to the screw terminals on the IR-2005 using a 3conductor wire (18-24AWG). CAT5 wire can be used, but only 3 of the 8 conductors are needed.
3-conductor
18-24 AWG wire
Expansion
IR
Receiver
Pwr
Global Zone
Model
P-1205
HANNEL
V ISION
IR
Receiver
Em itters
Global
+12DC
Zone
Sat radio
DVD player
CD player
Receiver
Whole-House IR Setup
IR-2005
IR-2005
(rear view)
IR1 IR2 IR3 IR4 IR5 IR6 IR7 IR8
C
+ S + S + S + S + S + S + S + S -
IR BUS
TM
+ S + -
POWER
C-1201
1
4
Po wer
7
8
5
0
9
2
6
3
Additional
IR receivers can be connected as needed.
3-conductor
18-24 AWG wire
Expansion
IR
Receiver
Pwr
Global Zone
Model
P-1205
HANNEL
ISION
IR
Receiver
Emitters
Global
+12DC
Zone
Sat radio
DVD player
CD player
Receiver
The diagram above illustrates how to create an IR system with IR receivers in several different rooms in the house. Systems like this may include several different styles of IR receivers depending on the specific application in each room.
IR-2005
