CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling (800) 840-
0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized service center.
500-167 rev A1
How IR repeating works
Expansio n
Pw r
IR
Receiver
Zon e
Model
P-1205
C
HANNEL
V ISION
TM
The IR receiver is wired to the IR hub which routes the signal to IR emitters
Glo ba
IR
Re cei ver
Emitters ne
Zo
+1
2D
250
C mA
Point an
IR remote control at the IR receiver
Tx
Ba
Pla y>
St op
Re w<
Le ar
FF >>
Pa us
2
1
5
3
6
4
8
9
-/-
7
Po we
0
Ch
Vo
Le ar ror
Er
Al l O
Of ct
Se le
Tu ne
VC
R
CD
DV
D
Sa
TV
TM on
Channe AB-500
And the emitter CD player repeats the IR signal in the other room.
Be sure the emitter is attached directly over the component’s IR receiver.
To locate the IR receiver, shine a flashlight into the unit and look for the sensor.
Specifications: (typical)
Voltage Requirements:
IR Freq. range supported:
IR pickup range:
IR receiver head dimensions:
Color:
8 - 12 VDC
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
0.65” x 0.35” x 0.25”
Black
Specifications subject to change without notice.
Input from
CATV
P-0321
Pat. Pending
Power
C
V
CATV Input
IR Out
IR-4101
Model
P-0321
MOD Input
Output
Using the IR-4101 & P-0321
Input from
Modulator
Digital CATV Box
TV set
A0502
MODEL
A0502
C
HANNEL
PO
W
O
N
ER
E
P
O
W
E
R
V
ISI
O
N
M
O
D
C
A
V
E
C
R
U
O S
M
U
E
CATV - Selects the CATV input on the P-0321
MOD - Selects the modulator input on the P-0321
The IR-4101 includes these items:
1 - IR coax adaptor with IR receiver
The IR-4101 is an IR coax adaptor that works with
Channel Vision’s IR coax engine to enable the transmission of Infrared remote control signals onto the same coax cable that delivers your cable TV.
Channel Vision’s IR coax engine can be found in the following products: IR-4000, E2200IR, E3200IR,
E4200IR, and P-0321.
36”
0.65”
IR receiver head
Features:
!
!
!
Versatile mounting accessaries: Install as
0.35”
Plasma Proof IR receiver
Compatible with: IR-4000, E2200IR, E3200IR, E4200I R, & P-0321
Very small receiver
In-cabinet tube type receiver
Unobtrusive desktop type receiver
Accessories
1 - IR receiver holster
1 - hole mount
1 - tabletop mount
Basic IR-on-coax Setup
A basic IR system, like the one shown below, is often used when an audio/video signal is distributed to a remote TV location using the RF output of the device. The IR-4101 is located near the TV, allowing IR signals to be detected, and the IR-4000 is located near the audio/video source, providing an IR emitter output.
IR-4101
AB-5
Channel ision
TV set
Using the IR-4101 with an E-series IR modulator
DC Block
HS-4
DC Passing splitter
DC Block and
75 ohm terminator
OUT /in
C H A N N E L V
OUT /in
4
Part No. HS-4
-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
OUT /in IN /out OUT /in
IR-4101
IR-4101
IR-4000
C H A N N E L V I S I O N T M
IR-4000
IR coax engine
IR emitter Pwr
IR Emitter
Ch. 3 output
IR Emitter VCR
DVD player CHANNEL VISION
T M
A B
E Series
Mounting the IR receiver: Option 2 - Using the hole mount
Drill a 3/4” hole .
Push the IR receiver head through the hole.
Insert the IR receiver head into the IR receiver hole mount.
Mounting the IR receiver: Option 1 - Using the holster
Mount the IR receiver to the TV or on a surface within line of sight of your remote control.
Remove the backing from the tape and attach the
IR receiver holster in the desired location.
Snap IR receiver head into the holster as shown.
Mounting the IR receiver: Option 3 - Using the tabletop mount
Push the IR receiver head through the hole in the tabletop mount.
Insert the IR receiver head into the IR receiver hole mount.
Push the IR receiver hole mount and IR receiver head back into the hole in the tabletop mount.
To secure the mount, remove the backing from the foam tape on the bottom of the unit and attach the mount to any flat surface.
Push the IR receiver hole mount and IR receiver head back into the hole.
