Char-Broil 11601558 Gas Grill User Manual

Contents
Introduction ...................................2
AV Receiver
Connection ..................................15
HT-RC160
Turning On & First Time Setup .....37
Instruction Manual
Basic Operations.........................50
Using the Listening Modes ........59
Advanced Setup ..........................66
Zone 2 .........................................82
Controlling Other Components ....86
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Others...........................................97
En
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
PORTABLE CART WARNING
12. Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
When a cart is used, use caution when moving the cart/
S3125A
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
2
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified technician to restore the apparatus to its normal
operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and follow local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is adequate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a fluelike gap for warm air to escape.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
5.
6.
7.
8.
Pressing the [ON/STANDBY] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine, fire or
the like.
Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
3
*
4
HIGH
WIDE
WIDE
WIDE
WIDE
FRONT
RIGHT
FRONT
LEFT
FRONT
RIGHT
FRONT
RIGHT
HIGH
FRONT
RIGHT
FRONT
LEFT
HIGH
HIGH
FRONT
LEFT
FRONT
LEFT
3
2
1
HIGH
LEFT
FRONT
FRONT
WIDE
RIGHT
WIDE
RIGHT
WIDE
LEFT
WIDE
LEFT
HIGH
RIGHT
FRONT
FRONT
FRONT
HIGH
LEFT
HIGH
RIGHT
FRONT
FRONT
FRONT
Speaker Cable
FRONT
LEFT
FRONT
LEFT
FRONT
LEFT
FRONT
LEFT
CENTER
SP-B/ZONE2
LEFT
SP-B/ZONE2
LEFT
SP-B/ZONE2
RIGHT
SP-B/ZONE2
RIGHT
SP-B/ZONE2
RIGHT
SP-B/ZONE2
RIGHT
SURROUND BACK
RIGHT
SURROUND BACK
RIGHT
SURROUND BACK
LEFT
SURROUND BACK
LEFT
SP-B/ZONE2
LEFT
SP-B/ZONE2
LEFT
SURROUND BACK
RIGHT
SURROUND BACK
RIGHT
SURROUND BACK
LEFT
SURROUND BACK
LEFT
CENTER
CENTER
SURROUND
RIGHT
SURROUND
RIGHT
SURROUND
RIGHT
SURROUND
RIGHT
CENTER
SURROUND
LEFT
SURROUND
LEFT
FRONT
RIGHT
FRONT
RIGHT
SURROUND
LEFT
SURROUND
LEFT
FRONT
RIGHT
FRONT
RIGHT
Supplied Accessories
Make sure you have the following accessories:
Remote controller & two batteries (AA/R6)
Speaker setup microphone
Indoor FM antenna
AM loop antenna
Speaker cable labels
(not supplied with the HT-S7200 Home Theater System.)
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operations are the
same regardless of color.
Contents
Introduction
Important Safety Instructions .................................... 2
Precautions ............................................................... 3
Supplied Accessories................................................ 4
Features .................................................................... 6
Multiroom Capability.................................................. 7
Front & Rear Panels.................................................. 8
Front Panel............................................................ 8
Display................................................................... 9
Rear Panel .......................................................... 10
Remote Controller ................................................... 12
Installing the Batteries ......................................... 12
Aiming the Remote Controller ............................. 12
Controlling the AV Receiver ................................ 13
About Home Theater............................................... 14
Enjoying Home Theater....................................... 14
Listening to the Radio.............................................. 53
Using the Tuner ................................................... 53
Presetting AM/FM Stations.................................. 54
UP-A1 series Dock for iPod..................................... 55
About the UP-A1 series Dock.............................. 55
Compatible iPod models...................................... 55
Putting Your iPod in the Dock.............................. 55
Function Overview............................................... 55
Controlling iPod ................................................... 56
Recording ................................................................ 58
Using the Listening Modes
Using the Listening Modes ...................................... 59
Selecting Listening Modes................................... 59
Listening Modes Available for Each
Source Format .................................................. 60
About the Listening Modes .................................. 64
Connection
Connecting the AV Receiver ................................... 15
Connecting Your Speakers ................................. 15
Bi-amping the Front Speakers............................. 18
Connecting Antenna............................................ 19
About AV Connections ........................................ 21
Connecting Components with HDMI ................... 22
Connecting Both Audio & Video .......................... 24
Which Connections Should I Use?...................... 24
Connecting a TV or Projector .............................. 26
Connecting a DVD/BD Player ............................. 27
Connecting a VCR or DVD/BD Recorder for
Playback ........................................................... 28
Connecting a VCR or DVD/BD Recorder for
Recording ......................................................... 29
Connecting a Satellite, Cable, Terrestrial Set-top
box, or Other Video Source .............................. 30
Connecting a Game Console .............................. 31
Connecting a Camcorder or Other Device .......... 32
Connecting a Portable Audio player.................... 32
Connecting a CD Player or Turntable ................. 33
Connecting a Cassette, CDR, MiniDisc, or DAT
Recorder ........................................................... 34
Connecting an RI Dock ....................................... 35
Connecting a Dock with the Universal Port connector ... 35
Connecting Onkyo u Components ................... 36
Connecting the Power Cord ................................ 36
Turning On & First Time Setup
Turning On the AV Receiver ................................... 37
Turning On and Standby ..................................... 37
First Time Setup...................................................... 38
Using the Onscreen Setup Menus ...................... 38
Using the Display to change the settings ............ 38
Video Input Setup................................................ 39
Digital Input Setup ............................................... 41
Speaker Settings ................................................. 42
FM/AM Frequency Step Setup ............................ 43
Changing the Input Display ................................. 44
Audyssey 2EQ™ Room Correction and
Speaker Setup .................................................. 45
Advanced Setup
Advanced Setup ...................................................... 66
Onscreen Setup Menus....................................... 66
Common Procedures in Setup Menu .................. 67
Speaker Setup..................................................... 67
Audio Adjust ........................................................ 70
Using the Audio Settings ..................................... 72
Assigning Listening Modes to Input Sources....... 74
Source Setup....................................................... 75
Miscellaneous (Volume/OSD) Setup ................... 77
Hardware Setup................................................... 78
Lock Setup........................................................... 80
Using the Video Settings ..................................... 80
Digital Input Signal Formats ................................ 81
Zone 2
Zone 2 ..................................................................... 82
Connecting Zone 2 .............................................. 82
Setting the Powered Zone 2 ................................ 83
Using Zone 2 ....................................................... 84
Controlling Other Components
Controlling Other Components................................ 86
Preprogrammed Remote Control Codes ............. 86
Looking up for Remote Control Code .................. 86
Entering Remote Control Codes.......................... 88
Remote Control Codes for Onkyo Components
Connected via u............................................. 89
Resetting REMOTE MODE Buttons .................... 89
Resetting the Remote Controller ......................... 89
Controlling a TV................................................... 90
Controlling a DVD/BD Player, or DVD/BD Recorder ... 91
Controlling a VCR or PVR ................................... 92
Controlling a Satellite Receiver or Cable Receiver ... 93
Controlling a CD Player ....................................... 94
Controlling an RI Dock......................................... 95
Controlling a Cassette Recorder ......................... 96
Others
Basic Operations
Basic Operations..................................................... 50
Selecting the Input Source .................................. 50
Adjusting the Bass & Treble ................................ 51
Displaying Source Information ............................ 51
Setting the Display Brightness ............................ 51
Muting the AV receiver ........................................ 52
Using the Sleep Timer......................................... 52
Using Headphones.............................................. 52
Troubleshooting....................................................... 97
Specifications ........................................................ 101
Video Resolution Chart ......................................... 102
* To reset the AV receiver to its factory defaults, turn it
on and, while holding down the [VCR/DVR] button,
press the [ON/STANDBY] button (see page 97).
5
Features
Amplifier
Miscellaneous
•
•
•
•
•
• 40 AM/FM Presets
• Audyssey 2EQ™*6 to Correct Room Acoustic Problems
• Audyssey Dynamic EQ™*6 for Loudness Correction
• Audyssey Dynamic Volume™*6 to Maintain Optimal
Listening Level and Dynamic Range
• Crossover Adjustment
(40/50/60/70/80/90/100/120/150/200 Hz)
• A/V Sync Control Function (up to 100 ms in 10 ms
steps)
• On-Screen Display via HDMI
• Aluminum Front Panel
• Preprogrammed (with On-Screen Display Set-up)
u-Compatible Remote
80 Watts/Channel @ 8 ohms
130 Watts/Channel @ 6 ohms
WRAT-Wide Range Amplifier Technology
Optimum Gain Volume Circuitry
H.C.P.S. (High Current Power Supply) Massive High
Power Transformer
Processing
• HDMI Video Upscaling (to 1080i Compatible) with
Faroudja DCDi Edge Enhancement
• HDMI ver.1.3a with Repeater System (Deep Color,
x.v.Color, Lip Sync, DTS*1-HD Master Audio,
DTS-HD High Resolution Audio, Dolby TrueHD*2,
Dolby Digital Plus, DSD and Multi-CH PCM)
• Dolby Pro Logic IIz*2 (with “Front High” Direction
Mode)
• Non-Scaling Configuration
• A-Form Listening Mode Memory
• Direct Mode
• Music Optimizer*3 for Compressed Music
• 192 kHz/24-bit D/A Converters
• Powerful and Highly Accurate 32-bit DSP Processing
Connections
•
•
•
•
•
•
•
•
•
•
5 HDMI*4 Inputs and 1 Output
Onkyo
for System Control
4 Digital Inputs (2 Optical / 2 Coaxial)
Component Video Switching (2 Inputs/1 Output)
Front “Portable” Input for iPod and MP3 Players
Universal Port for the Dock for the iPod/HD Radio™*5
Dock
Dual Subwoofer Pre Out
Banana Plug-Compatible Speaker Posts
Powered Zone 2 and Zone 2 Line Out
Bi-Amp Capability for Music and Movie Sound
Effects
*1.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;
7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc.
©1996-2008 DTS, Inc. All Rights Reserved.
*2.
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
*3. Music Optimizer™ is a trademark of Onkyo Corporation.
*4.
HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
*5.
HD Radio™ and the HD Radio Ready logo are proprietary
trademarks of iBiquity Digital Corporation.
To receive HD Radio broadcasts, you must install an Onkyo
UP-HT1 HD Radio tuner module (sold separately).
*6.
Manufactured under license from Audyssey Laboratories. U.S.
and foreign patents pending. Audyssey 2EQ™,
Audyssey Dynamic Volume™ and Audyssey Dynamic EQ™
are trademarks of Audyssey Laboratories.
*
*
6
Apple and iPod are trademarks of Apple Inc., registered in the
U.S. and other countries.
“x.v.Color” is a trademark of Sony Corporation.
Multiroom Capability
You can use two speaker systems with this AV receiver—a surround-sound speaker system (up to 7.1 channels) in
your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it. And, you can select a
different audio source for each room.
Main Room: In your main listening room, you can enjoy up to 7.1-channel playback (see page 14).
You can enjoy the various listening modes such as Dolby and DTS (see pages 59-65).
* While Powered Zone 2 is being used, playback is reduced to 5.1-channels (see page 82).
Zone 2: In your Zone 2 room, you can enjoy 2-channel stereo playback (see page 82).
* The listening modes cannot be used with Zone 2.
Main Room
Front high left and right speakers
Surround back left and right
speakers
• While Powered Zone 2 is being
used, nothing is output by these
speakers (page 82).
Front left and right
speakers
• Front high and surround back
speakers produce no sound at the
same time.
• While Powered Zone 2 is being used,
nothing is output by these speakers
(page 82).
• Front high and surround back
speakers produce no sound at the
same time.
Center speaker
Subwoofer
Surround left and right speakers
Zone 2 Room
Left and right
stereo speakers
7
Front & Rear Panels
Front Panel
a
bc
d e
f
g h i j k l mn
r
s
o
p
q
t
u
The actual front panel has various logos printed on it. They are not shown here for clarity.
The page numbers in parentheses show where you can find the main explanation for each item.
a ON/STANDBY button (37)
i GAME button (59)
This button is used to set the AV receiver to On or
Selects the listening modes intended for use with
Standby.
video games.
b STANDBY indicator (37)
This indicator lights up when the AV receiver is in
Standby mode, and it flashes while a signal is being
received from the remote controller.
c ZONE 2 indicator (84)
This indicator lights up when Zone 2 is selected.
d ZONE 2 LEVEL/TONE LEVEL buttons
ZONE 2 and OFF buttons (84)
The [ZONE 2] button is used to turn on the output
of Zone 2.
The [OFF] button is used to turn off the output of
Zone 2.
[–] & [+] buttons (51, 85)
Used to adjust the tone (bass and treble), and the
level of Zone 2.
TONE button (51)
Used to select either bass or treble.
e Remote control sensor (12)
This sensor receives control signals from the remote
controller.
f Display
See “Display” on page 9.
g MOVIE/TV button (59)
Selects the listening modes intended for use with
movies and TV.
h MUSIC button (59)
Selects the listening modes intended for use with
music.
8
j DIMMER button (51)
This button is used to adjust the display brightness.
k MEMORY button (54)
This button is used when storing or deleting radio
presets.
l TUNING MODE button (53)
This button is used to select the Auto or Manual
tuning mode.
m DISPLAY button (51)
This button is used to display various information
about the currently selected input source.
n SETUP button
This button is used to access the onscreen setup
menus that appear on the connected TV.
o Arrow, TUNING, PRESET and ENTER
buttons
When the AM or FM input source is selected, the
TUNING [q]/[w] buttons are used to tune the tuner,
and the PRESET [e]/[r] buttons are used to select
radio presets (see pages 53, 54).
When the onscreen setup menus are used, they work
as arrow buttons and are used to select and set
items. The [ENTER] button is also used with the
onscreen setup menus.
p RETURN button
This button is used to return to the previously displayed onscreen setup menu.
Front & Rear Panels—Continued
q MASTER VOLUME control (50)
This control is used to adjust the volume of the AV
receiver to Min, 1 through 79 or Max.
r PHONES jack (52)
This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.
s Input selector buttons (50)
These buttons are used to select from the following
input sources: DVD/BD, VCR/DVR, CBL/SAT,
GAME, AUX, TV/TAPE, TUNER, CD, PORT.
t AUX INPUT (32)
This input can be used to connect a camcorder,
game console, and so on. There are jacks for composite video, and analog audio.
PORTABLE (32):
Used to connect a portable Audio Player.
u SETUP MIC jack (46)
The Audyssey 2EQ™ Room Correction and
Speaker Setup microphone connects here.
Display
a b
e
c
f
d
g
For detailed information, see the pages in parentheses.
a SLEEP indicator (52)
Lights up when the Sleep function has been set.
b MUTING indicator (52)
Flashes while the AV receiver is muted.
c Listening mode and format indicators (59)
Show the selected listening mode and audio input
signal format.
d Tuning indicators (53)
AUTO (53):
Lights up when Auto Tuning mode is selected for
AM or FM radio. Goes off when Manual Tuning
mode is selected.
TUNED (53):
Lights up when tuned to a radio station.
FM STEREO (53):
Lights up when tuned to a stereo FM station.
e Message area
Displays various information.
f Audio input indicators
Indicate the type of audio input that’s selected as the
audio source: PCM, MULTI CH, or HDMI.
g Audyssey indicator (45, 69)
Flashes during Audyssey 2EQ™ Room Correction
and Speaker Setup. Lights up when the “Equalizer
Settings” is set to “Audyssey”.
9
Front & Rear Panels—Continued
Rear Panel
a bc
j
d e
f gh
k l mn o p qr
a DIGITAL IN COAXIAL 1 and 2
These coaxial digital audio inputs are for connecting components with coaxial digital audio outputs,
such as CD and DVD/BD players. They’re assignable, which means you can assign each one to an
input selector to suit your setup. See “Digital Input
Setup” on page 41.
b DIGITAL IN OPTICAL 1 and 2
These optical digital audio inputs are for connecting
components with optical digital audio outputs, such
as CD and DVD/BD players. They’re assignable,
which means you can assign each one to an input
selector to suit your setup. See “Digital Input
Setup” on page 41.
c COMPONENT VIDEO IN 1 and 2
These RCA component video inputs are for connecting components with a component video output, such as a DVD/BD player, DVD/BD recorder,
or DVR (digital video recorder). They’re assignable,
which means you can assign each one to an input
selector to suit your setup. See “Component Video
Setup” on page 40.
d COMPONENT VIDEO OUT
This RCA component video output is for connecting a TV or projector with a component video input.
e HDMI IN 1–5 and OUT
HDMI (High Definition Multimedia Interface) connections carry digital audio and digital video.
The HDMI inputs are for connecting components
with an HDMI output, such as a DVD/BD player,
DVD/BD recorder, or DVR (digital video recorder).
They’re assignable, which means you can assign
each one to an input selector to suit your setup. See
“HDMI Input Setup” on page 39.
The HDMI output is for connecting a TV or projector with an HDMI input.
10
i
s
f FM ANTENNA
This jack is for connecting an FM antenna.
AM ANTENNA
These push terminals are for connecting an AM
antenna.
g MONITOR OUT V
The composite video jack should be connected to a
video input on your TV or projector.
h UNIVERSAL PORT
This jack is for connecting the component with the
Universal Port connector such as UP-A1 series
Dock.
i FRONT L/R, CENTER, SURR L/R, and SURR
BACK L/R speakers
These terminal posts are for connecting the front
L/R, center, surround L/R, surround back L/R, and
front high L/R speakers.
The FRONT L/R and SURR BACK L/R terminal
posts can be used with front speakers and surround
back speakers respectively, or used to bi-amp the
front speakers. See “Bi-amping the Front Speakers”
on page 18”.
The SURR BACK L/R terminals can be used to
connect the front high L/R speakers. See “Speaker
Settings” on page 42.
j u REMOTE CONTROL
This u (Remote Interactive) jack can be connected to an u jack on another Onkyo AV component. The AV receiver’s remote controller can then
be used to control that component. To use u, you
must make an analog audio connection (RCA)
between the AV receiver and the other AV component, even if they are connected digitally.
Front & Rear Panels—Continued
k CD IN
This analog audio input is for connecting a CD
player’s analog audio output.
l TV/TAPE IN/OUT
This analog audio input and output are for connecting a recorder with an analog audio input and output
(cassette, Mini Disc, etc.).
m GAME IN
Here you can connect a game console, etc. Input
jacks include composite video and analog audio.
n CBL/SAT IN
Here you can connect a cable/satellite receiver, settop box, etc. Input jacks include composite video
and analog audio.
o VCR/DVR IN/OUT
Here you can connect a VCR or DVR (digital video
recorder). Input and output jacks include composite
video and analog audio.
p DVD/BD IN
Here you can connect a DVD/BD player. Input
jacks include composite video and analog audio.
You can connect a DVD/BD player’s 2-channel analog audio output.
q ZONE 2 LINE OUT L/R
This analog audio output can be connected to a line
input on an integrated amplifier in Zone 2. See
“Connecting Zone 2” on page 82.
r PRE OUT: SUBWOOFER
This analog audio outputs can be connected to a
powered subwoofer. The same signal is output from
each jack. You can connect the powered subwoofer
with two SUBWOOFER PREOUT jacks respectively.
s FRONT HIGH L/R speakers
These terminals are for connecting the front high
L/R speakers.
The FRONT HIGH L/R terminal can be used with
front high speakers respectively, or used to connect
the speakers in Zone 2.
See “Connecting Zone 2” on page 82.
See pages 15-36 for connection information.
11
Remote Controller
Installing the Batteries
1
To open the battery compartment, press
the small lever and remove the cover.
Aiming the Remote Controller
To use the remote controller, point it at the AV receiver’s
remote control sensor, as shown below.
Remote control sensor
AV receiver
STANDBY indicator
Approx. 16 ft. (5 m)
2
3
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
Replace the cover and push it shut.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.
12
Notes:
• The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in
mind when installing.
• If another remote controller of the same type is used in
the same room, or the AV receiver is installed close to
equipment that uses infrared rays, the remote controller may not work reliably.
• Don’t put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.
• The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an
obstacle between it and the AV receiver’s remote control sensor.
• When the remote control codes have been registered
and you want to operate another component (page 86),
or when you want to operate an Onkyo component
without u connection, point the remote controller at
the other component to use it.
• When you want to operate an Onkyo component with
u connection or an
-compatible component connected via HDMI (pages 90, 91), point the
remote controller at the AV receiver’s remote control
sensor.
Remote Controller—Continued
Controlling the AV Receiver
To control the AV receiver, press the [RECEIVER]
button to select Receiver mode.
You can also use the remote controller to control your
DVD/BD player, CD player, and other components.
See page 88 for more details.
e LISTENING MODE buttons (59)
Used to select the listening modes.
f DIMMER button (51)
Adjusts the display brightness.
g DISPLAY button (51)
Displays information about the current input source.
h MUTING button (52)
Mutes or unmutes the AV receiver.
a
g3
b
h
i
4
1c
j
d
k
l
j VIDEO button (80)
Used to change video settings.
k RETURN button
Returns to the previous display when changing settings.
l AUDIO button (72)
Used to change audio settings.
When the “Audio TV Out” setting is set to “On”
(page 78), this button is disabled.
m SLEEP button (52)
Used with the Sleep function.
■ Controlling the tuner
To control the AV receiver’s tuner, press the [TUNER]
(or [RECEIVER]) button.
You can select AM or FM by pressing the [TUNER] button repeatedly.
e
2f
i VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver regardless of
the currently selected remote controller mode.
5
1
Arrow [q]/[w] buttons
Used to tune into radio stations.
m
2
D.TUN button (53)
Selects the Direct tuning mode.
3
DISPLAY button
Displays information about the band, frequency,
preset number, and so on.
4
CH +/– button (54)
Used to select radio presets.
5
For detailed information, see the pages in parentheses.
a ON/STANDBY button (37)
Sets the AV receiver to On or Standby.
b REMOTE MODE/INPUT SELECTOR buttons
(50, 90–96)
Selects the remote controller modes and the input
sources.
Number buttons (53)
Used to select radio stations directly in the Direct
tuning mode. Also you can select a preset directly.
Note:
An Onkyo cassette recorder connected via u can also
be controlled in Receiver mode (see page 96).
c Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to select and adjust settings.
d SETUP button
Used to change settings.
13
About Home Theater
Enjoying Home Theater
Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your
own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With
analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.
Front left and right speakers
These output the overall sound. Their role in a home theater is to provide a solid anchor for the
sound image. They should be positioned facing the listener at about ear level, and equidistant from
the TV. Angle them inward so as to create a triangle, with the listener at the apex.
Front high left and right speakers
These speakers are necessary to enjoy Dolby Pro Logic IIz Height, etc.
They enhance significantly the spatial experience.
Position them at least 3.3 feet (100 cm) above the front left and right
speakers (and as high as possible). Although it is acceptable to
place left and right at an angle slightly wider than the front left and
right speakers. Ideally they should be positioned directly above the
front left and right speakers. Front high and surround back speakers
produce no sound at the same time.
Surround back left and right
speakers
These speakers are necessary to
enjoy Dolby Digital EX, DTS-ES
Matrix, DTS-ES Discrete, etc. They
enhance the realism of surround
sound and improve sound localization behind the listener. Position
them behind the listener about 2–
3 feet (60–100 cm) above ear level.
Front high and surround back
speakers produce no sound at the
same time.
Center speaker
This speaker enhances the
front left and right speakers,
making sound movements distinct and providing a full sound
image. In movies it’s used
mainly for dialog.
Position it close to your TV facing forward at about ear level, or
at the same height as the front
left and right speakers.
Subwoofer
The subwoofer handles the bass sounds
of the LFE (Low-Frequency Effects)
channel. The volume and quality of the
bass output from your subwoofer will
depend on its position, the shape of your
listening room, and your listening position. In general, a good bass sound can
be obtained by installing the subwoofer in
a front corner, or at one-third the width of
the wall, as shown.
You can connect the powered subwoofer
with two SUBWOOFER PREOUT jacks
respectively.
Tip: To find the best position for your subwoofer, while playing a movie or some
music with good bass, experiment by
placing your subwoofer at various positions within the room, and choose the one
that provides the most satisfying results.
1/3 of wall
position
14
Surround left and right speakers
These speakers are used for precise sound positioning and
to add realistic ambience.
Position them at the sides of the listener, or slightly behind,
about 2–3 feet (60–100 cm) above ear level. Ideally they
should be equidistant from the listener.
Corner
position
Connecting the AV Receiver
Connecting Your Speakers
Speaker Configuration
For 7.1-channel surround-sound playback, you need
seven speakers and a powered subwoofer.
The following table indicates the channels you should
use depending on the number of speakers that you have.
Number of speakers:
2
Front left
✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
Front right
✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
Center
3
✓
4
5
7
7
8
9
✓ ✓ ✓ ✓ ✓ ✓
Surround left
✓ ✓ ✓ ✓ ✓ ✓ ✓
Surround right
✓ ✓ ✓ ✓ ✓ ✓ ✓
Surround back*
*
6
✓
✓
Surround back left
✓
Surround back right
✓
✓
✓
Front high left
✓ ✓ ✓
Front high right
✓ ✓ ✓
• Speaker cable labels is not supplied with the
HT-S7200 Home Theater System.
• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.
• Do not insert the speaker code directly into the center
hole of the speaker terminal.
Using Dipole Speakers
You can use dipole speakers for the surround left and
right, surround back left and right and front high left and
right speakers. Dipole speakers output the same sound in
two directions.
Dipole speakers typically have an arrow printed on them
to indicate how they should be positioned. The surround
left and right dipole speakers should be positioned so
that their arrows point toward the TV/screen, while the
surround back left and right and front high left and right
dipole speakers should be positioned so that their arrows
point toward each other, as shown.
9
If you’re using only one surround back speaker, connect it to the
SURR BACK L terminals.
No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid
bass.
To get the best from your surround sound system, you
need to set the speaker settings. You can do this automatically (see page 45) or manually (see page 67).
Note:
Front high and surround back speakers produce no sound
at the same time.
Attaching the Speaker Labels
The AV receiver’s positive (+) speaker terminals are all
red (the negative (–) speaker terminals are all black).
Speaker
Color
Front left, Zone 2 left
White
Front right, Zone 2 right
Red
Center
Green
Surround left
Blue
Surround right
Gray
Surround back left
Brown
Surround back right
Tan
Front high left
White
Front high right
Red
Normal speakers
Dipole speakers
9
10
TV/screen
1
2
TV/screen
4
3
5
1
2
6
7
10
8
1.Subwoofer
2.Front left speaker
3.Center speaker
4.Front right speaker
5.Surround left speaker
6.Surround right speaker
4
3
5
6
7
8
7.Surround back left
speaker
8.Surround back right
speaker
9.Front high left speaker
10.Front high right speaker
The supplied speaker cable labels are also color-coded
and you should attach them to the positive (+) side of
each speaker cable in accordance with the above table.
Then all you need to do is to match the color of each
label to the corresponding speaker terminal.
15
Connecting the AV Receiver—Continued
Connecting a Powered Subwoofer
Using a suitable cable, connect the AV receiver’s PRE
OUT: SUBWOOFER to an input on your powered subwoofer, as shown. If your subwoofer is unpowered and
you’re using an external amplifier, connect the PRE
OUT: SUBWOOFER to an input on the amp.
You can connect the powered subwoofer with two SUBWOOFER PREOUT jacks respectively.
The same signal is output from each jack.
Powered
subwoofer
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.
Connecting the Speaker Cables
1
Strip 1/2"-5/8" (1215 mm) of insulation
from the ends of the
speaker cables, and
twist the bare wires
tightly, as shown.
2
Unscrew the terminal.
3
Fully insert the bare
wires.
4
Screw the terminal tight.
LINE INPUT
LINE INPUT
1/2"-5/8"(12-15 mm)
Speaker Connection Precautions
Read the following before connecting your speakers:
• You can connect speakers with an impedance of
between 6 and 16 ohms. If you use speakers with a
lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp
protection circuit may be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• If you use 4 or 5 speakers, connect each of the two
surround speakers to the SURR L/R terminals. Do not
connect them to the SURR BACK L/R or FRONT
HIGH L/R terminals.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
• Make sure the metal core of
the wire does not have contact
with the AV receiver’s rear
panel. Doing so may damage
the AV receiver.
16
FRONT HIGH L/R, ZONE 2 L/R
1
Strip 3/8"-1/2" (1012 mm) of insulation
from the ends of the
speaker cables, and
twist the bare wires
tightly, as shown.
2
While pressing the lever,
insert the wire into the
hole, and then release the
lever.
Make sure that the terminals are gripping the bare wires, not the
insulation.
3/8"-1/2"(10-12 mm)
Connecting the AV Receiver—Continued
The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one
surround back speaker, connect it to the left (L) SURR BACK SPEAKERS terminals.
Surround
back left
speaker
Front high
left
speaker
Front high
right
speaker
Surround
back right
speaker
Front left
speaker
Surround
left
speaker
Front right
speaker
Surround
right
speaker
Center
speaker
17
Connecting the AV Receiver—Continued
Bi-amping the Front Speakers
The FRONT L/R and SURR BACK L/R terminal posts
can be used with front speakers and surround back
speakers respectively, or bi-amped to provide separate
tweeter and woofer feeds for a pair of front speakers that
support bi-amping, providing improved bass and treble
performance.
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• For bi-amping, the FRONT L/R terminal posts connect to the front speakers’ woofer terminals. And the
SURR BACK L/R terminal posts connect to the front
speakers’ tweeter terminals.
• Once you’ve completed the bi-amping connections
shown below and turned on the AV receiver, you must
set the “Speaker Type” setting to “Bi-Amp” to enable
biamping (see page 42).
Important:
• When making the bi-amping connections, be sure
to remove the jumper bars that link the speakers’
tweeter (high) and woofer (low) terminals.
• Bi-amping can only be used with speakers that support
bi-amping. Refer to your speaker manual.
Bi-amping Speaker Hookup
1
Connect the AV receiver’s FRONT R positive (+)
terminal to the right speaker’s positive (+) Woofer
(low) terminal. And connect the AV receiver’s
FRONT R negative (–) terminal to the right
speaker’s negative (–) Woofer (low) terminal.
2
Connect the AV receiver’s SURR BACK R positive (+) terminal to the right speaker’s positive (+)
Tweeter (high) terminal. And connect the AV
receiver’s SURR BACK R negative (–) terminal
to the right speaker’s negative (–) Tweeter (high)
terminal.
3
Connect the AV receiver’s FRONT L positive (+)
terminal to the left speaker’s positive (+) Woofer
(low) terminal. And connect the AV receiver’s
FRONT L negative (–) terminal to the left
speaker’s negative (–) Woofer (low) terminal.
4
Connect the AV receiver’s SURR BACK L positive (+) terminal to the left speaker’s positive (+)
Tweeter (high) terminal. And connect the AV
receiver’s SURR BACK L negative (–) terminal to
the left speaker’s negative (–) Tweeter (high) terminal.
FRONT SPEAKERS
L
L
Left speaker
Tweeter (high)
Woofer (low)
R
R
Right speaker
18
Tweeter (high)
Woofer (low)
Connecting the AV Receiver—Continued
Connecting the AM Loop Antenna
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The AV Receiver won’t pick up any radio signals without any antenna connected, so you must connect the
antenna to use the tuner.
FM ANTENNA
jack
The supplied indoor FM antenna is for indoor use only.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2
Connect both wires of the AM loop
antenna to the AM antenna push terminals, as shown.
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around.)
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Attach the FM antenna, as shown.
Insert the plug fully
into the jack.
Once your AV Receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
2
1
AM ANTENNA push terminals
Connecting the Indoor FM Antenna
1
The supplied indoor AM loop antenna is for indoor use
only.
Use thumbtacks or something similar to
fix the FM antenna into position.
Push
Insert wire
Release
Once your AV Receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from
your AV Receiver, TV, speaker cables, and power
cords.
Thumbtacks, etc.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 20).
Caution:
Be careful that you don’t injure yourself when
using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 20).
19
Connecting the AV Receiver—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor antenna
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock hazards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To AV Receiver
20
To TV (or VCR)
Insulated antenna cable
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
Connecting the AV Receiver—Continued
AV Connection Color Coding
About AV Connections
• Before making any AV connections, read the manuals
supplied with your other AV components.
• Don’t connect the power cord until you’ve completed
and double-checked all AV connections.
Optical Digital Jacks
The AV receiver’s optical digital jacks have shutter-type
covers that open when an optical plug is inserted and
close when it’s removed. Push plugs in all the way.
Caution:
To prevent shutter damage, hold the optical plug straight
when inserting and removing.
RCA-type AV connections are usually color-coded: red,
white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use
white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
Left (white)
Analog audio
Right (red)
(Yellow)
Left (white)
Right (red)
Composite video
• Push plugs in all the way to make
good connections (loose connections can cause noise or malfunctions).
• To prevent interference, keep
audio and video cables away from
power cords and speaker cables.
(Yellow)
Right!
Wrong!
AV Cables & Jacks
Video / Audio
Cable
Jack
HDMI
HDMI
Description
HDMI connections can carry uncompressed standard- or high-definition digital video and audio and
offer the best picture and sound quality.
Video
Y
Component
video cable
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the best
picture quality (some TV manufacturers label their
component video sockets slightly differently).
Y
PB/CB
PB/CB
PR/CR
PR/CR
Composite
video cable
V
Composite video is commonly used on TVs, VCRs,
and other video equipment.
Audio
OPTICAL
Optical digital
audio cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for optical.
Coaxial digital
audio cable
Analog audio
cable (RCA)
Stereo mini plug
cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for coaxial.
L
R
This cable carries analog audio. It’s the most common connection format for analog audio, and can be
found on virtually all AV components.
This cable carries analog audio.
The AV receiver does not support SCART plugs.
21
Connecting the AV Receiver—Continued
Connecting Components with HDMI
About HDMI
Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital
interface standard for connecting TVs, projectors, DVD/BD players, set-top boxes, and other video components. Until
now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable
can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital
audio, and multichannel PCM).
The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays
with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and
displays, resulting in no picture.)
The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components
can display the picture.
The AV receiver’s HDMI interface is based on the following standard:
x.v.Color, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD,
Dolby Digital Plus, DSD, and Multichannel PCM
Supported Audio Formats
• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)
• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio)
Your DVD/BD player must also support HDMI output of the above audio formats.
■ Onkyo
for System Control
, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo
components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over
HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than
-compatible components cannot be guaranteed.
• Set “HDMI Control (RIHD)” to “On” (page 79).
• See “Controlling a TV” (page 90) and “Controlling a DVD/BD Player, or DVD/BD Recorder” (page 91) for operation.
Note:
Do not connect the
-compatible component more than the following number to the HDMI input terminal so
that the linked operations work properly.
• DVD/BD player is up to three.
• DVD/BD recorder is up to three.
• Cable/Satellite Set-top box is up to four.
Do not connect the AV receiver to the other AV receiver /AV amplifier via HDMI.
When the
-compatible component more than the above-mentioned is connected, the linked operations are not
guaranteed.
About Copyright Protection
The AV receiver supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection system for digital
video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.
*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999.
*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to
protect video content and requires a HDCP-compatible device to display the encrypted video.
*3 DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open
industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance PCs and
digital displays.
22
Connecting the AV Receiver—Continued
Making HDMI Connections
Step 1:
Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible Blu-ray player/DVD player,
TV, projector, and so on.
Step 2:
Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 39).
■ Video Signals
Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.
Composite video and component video sources can be upconverted for the HDMI output. See “Video Connection Formats” on page 24 for more information.
■ Audio Signals
Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV
receiver. Normally, they are not output by the HDMI OUT, unless the “Audio TV Out” setting is set to “On” (see
page 78).
Hint!
To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the “Audio TV Out”
setting to “On” (see page 78), and set your DVD/BD player’s HDMI audio output setting to PCM.
HDMI
IN
HDMI
OUT
TV
Blu-ray player/DVD player
HDMI
HDMI
IN 1
(DVD/BD)
Notes:
• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can
be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need
to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In
addition, video signals from a PC are not supported.
• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be
seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV
power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound
may be cut off.
• When the “Audio TV Out” setting is set to “On” (see page 78), or “TV Control” is set to “On” (see page 79) and
you’re listening through your TV’s speakers, if you turn up the AV receiver volume control, the sound will be output
by the AV receiver’s speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your
TV’s settings, or turn down the AV receiver’s volume.
• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the
picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected
component’s instruction manual for details.
23
Connecting the AV Receiver—Continued
Connecting Both Audio & Video
By connecting both the audio and video outputs of your DVD/BD player and other AV components to the AV receiver,
you can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV
receiver.
: Signal Flow
Video
Video
Audio
Audio
TV, projector,
etc.
DVD/BD player, etc.
Speakers
(see page 17 for connection information)
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your other components. Use the following sections as a guide.
Video Connection Formats
Video equipment can be connected to the AV receiver by using any one of the following video connection formats:
composite video, component video, or HDMI, the latter offering the best picture quality.
Video input signals flow through the AV receiver
as shown, with composite video and component
video sources all being upconverted for the
HDMI output.
The composite video and component video outputs pass through their respective input signals as
they are.
When you connect audio equipment to an HDMI
or COMPONENT input, you must assign that
input to an input selector (see pages 39 and 40).
DVD/BD player, etc.
Video Signal Flow Chart
Composite
HDMI
IN
AV receiver
MONITOR OUT
Composite
TV, projector, etc.
24
Component
Component
HDMI
Connecting the AV Receiver—Continued
■ Signal Selection
If signals are present at more than one input, the
inputs will be selected automatically in the following order of priority: HDMI, component
video, composite video.
However, for component video only, regardless
of whether a component video signal is actually
present, if a component video input is assigned to
the input selector, that component video input
will be selected. And if no component video
input is assigned to the input selector, this will be
interpreted as no component video signal being
present.
In the Signal Selection Example shown on the
right, video signals are present at both the HDMI
and composite video inputs, however, the HDMI
signal is automatically selected as the source and
video is output by the HDMI outputs.
A video signal from the Composite Video In jack
is output from the Composite Video Out jack
regardless of the output priority.
DVD/BD player, etc.
Signal Selection Example
Composite
Component
HDMI
IN
AV receiver
MONITOR OUT
Component
Composite
HDMI
TV, projector, etc.
The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the
MONITOR OUT V, or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.
Audio Connection Formats
Audio equipment can be connected to the AV
receiver by using any of the following audio connection formats: analog, optical, coaxial, or
HDMI.
When choosing a connection format, bear in
mind that the AV receiver does not convert digital
input signals for analog line outputs and vice
versa. For example, audio signals connected to
an optical or coaxial digital input are not output
by the analog TV/TAPE OUT.
DVD/BD player, etc.
Audio Signal Flow Chart
Analog
Optical
Coaxial
HDMI
IN
AV receiver
OUT
Analog
TV, projector, etc.
HDMI
*1 Depends on the “Audio TV Out” setting
(see page 78).
If signals are present at more than one input, the inputs will be selected automatically in the following order of priority:
HDMI, digital, analog.
25
Connecting the AV Receiver—Continued
Connecting a TV or Projector
See “Connecting Components with HDMI” on page 22 for HDMI connection information.
Step 1: Video Connection
Choose a video connection that matches your TV ( A or B ), and then make the connection.
Step 2: Audio Connection
Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection.
The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the
MONITOR OUT V, or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.
• With connection a , you can listen to and record audio from your TV and listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (To record or listen in Zone 2 as well, use a and b ,
or a and c .)
Connection
AV receiver
Signal flow
TV
A
COMPONENT VIDEO OUT
⇒
Component video input
B
MONITOR OUT V
⇒
Composite video input
a
TV/TAPE IN L/R
⇐
Analog audio L/R output
b
DIGITAL IN COAXIAL 2 (CBL/SAT)
⇐
Digital coaxial output
c
DIGITAL IN OPTICAL 1 (GAME)
⇐
Digital optical output
c
B
b
a
A
L
OPTICAL
OUT
COAXIAL
OUT
Connect one or the other
Connection b , c must be assigned (see page 41)
Hint!
26
PR
Y
PB
COMPONENT VIDEO IN
R
AUDIO
OUT
VIDEO
IN
TV, projector,
etc.
If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver
to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see pages 28 and
30).
Connecting the AV Receiver—Continued
Connecting a DVD/BD Player
See “Connecting Components with HDMI” on page 22 for HDMI connection information.
Step 1: Video Connection
Choose a video connection that matches your DVD/BD player ( A or B ), and then make the connection.
You must connect the AV receiver to your TV via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your DVD/BD player ( a , b , or c ), and then make the connection.
• With connection a , you can listen to and record audio from a DVD/BD and listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (To record or listen in Zone 2 as well, use a and b ,
or a and c .)
• If your DVD/BD player has main left and right outputs and multichannel left and right outputs, be sure to use
the main left and right outputs for connection a .
Connection
AV receiver
Signal flow
DVD/BD player
A
COMPONENT VIDEO IN 1 (DVD/BD)
⇐
Component video output
B
DVD/BD IN V
⇐
Composite video output
a
DVD/BD IN L/R
⇐
Analog audio L/R output
b
DIGITAL IN COAXIAL 1 (DVD/BD)
⇐
Digital coaxial output
c
DIGITAL IN OPTICAL 1 (GAME)
⇐
Digital optical output
c
B
b
A
a
L
OPTICAL
OUT
COAXIAL
OUT
Y
PB
PR
COMPONENT VIDEO OUT
R
AUDIO
OUT
VIDEO
OUT
Connect one or the other
Connection c must be assigned (see page 41)
DVD/BD player
27
Connecting the AV Receiver—Continued
Connecting a VCR or DVD/BD Recorder for Playback
Hint!
With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV
receiver, useful if your TV has no audio outputs.
Step 1: Video Connection
Choose a video connection that matches your VCR or DVD/BD recorder ( A or B ), and then make the connection.
You must connect the AV receiver to your TV via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your VCR or DVD/BD recorder ( a , b , or c ), and then make the connection.
• With connection a , you can listen to the VCR or DVD/BD recorder even in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (To listen in Zone 2 as well, use a and b , or a and
c .)
Connection
AV receiver
Signal flow
VCR or DVD/BD recorder
A
COMPONENT VIDEO IN 1 (DVD/BD)
⇐
Component video output
B
VCR/DVR IN V
⇐
Composite video output
a
VCR/DVR IN L/R
⇐
Analog audio L/R output
b
DIGITAL IN COAXIAL 1 (DVD/BD)
⇐
Digital coaxial output
c
DIGITAL IN OPTICAL 1 (GAME)
⇐
Digital optical output
.
c
B
b
a
Connection
A must be
assigned
(see
page 40)
A
L
OPTICAL
OUT
COAXIAL
OUT
Y
PB
PR
COMPONENT VIDEO OUT
Connect one or the other
Connection b , c must be assigned (see page 41)
VCR,
DVD/BD recorder
28
R
AUDIO
OUT
VIDEO
OUT
Connecting the AV Receiver—Continued
Connecting a VCR or DVD/BD Recorder for Recording
Step 1: Video Connection
Make the video connection A . The video source to be recorded must be connected to the AV receiver via the same
type of connection.
Step 2: Audio Connection
Make the audio connection a .
Connection
AV receiver
Signal flow
VCR or DVD/BD recorder
A
VCR/DVR OUT V
⇒
Composite video input
VCR/DVR OUT L/R
⇒
Analog audio L/R input
a
A
B
a
L
R
AUDIO
IN
VIDEO
IN
VCR, DVD/BD
recorder
Notes:
• The AV receiver must be turned on for recording. Recording is not possible while it’s in Standby mode.
• If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV
receiver, connect the TV/VCR’s audio and video outputs directly to the recording VCR’s audio and video inputs. See
the manuals supplied with your TV and VCR for details.
• Video signals connected to composite video inputs can only be recorded via composite video outputs. If your
TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output.
29
Connecting the AV Receiver—Continued
Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
Hint!
With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs
via the AV receiver, useful if your TV has no audio outputs.
Step 1: Video Connection
Choose a video connection that matches the video source ( A or B ), and then make the connection.
You must connect the AV receiver to your TV via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches the video source ( a , b , or c ), and then make the connection.
• With connection a , you can listen to and record audio from the video source and listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (To listen in Zone 2 as well, use a and b , or a and
c .)
Connection
AV receiver
Signal flow
Video source
A
COMPONENT VIDEO IN 2 (CBL/SAT)
⇐
Component video output
B
CBL/SAT IN V
⇐
Composite video output
a
CBL/SAT IN L/R
⇐
Analog audio L/R output
b
DIGITAL IN COAXIAL 2 (CBL/SAT)
⇐
Digital coaxial output
c
DIGITAL IN OPTICAL 2 (CD)
⇐
Digital optical output
c
B
b
a
A
L
OPTICAL
OUT
COAXIAL
OUT
PR
Y
PB
COMPONENT VIDEO OUT
R
AUDIO
OUT
VIDEO
OUT
Connect one or the other
Connection c must be assigned (see page 41)
Satellite, cable, set-top box, etc.
30
Connecting the AV Receiver—Continued
Connecting a Game Console
Step 1: Video Connection
Choose a video connection that matches the game console ( A or B ), and then make the connection.
You must connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches the game console ( a or b ), and then make the connection.
• With connection a , you can listen to and record audio from the game console or listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b . (To record or listen in Zone 2 as well, use a and b .)
Connection
AV receiver
Signal flow
Game console
A
COMPONENT VIDEO IN 2 (CBL/SAT)
⇐
Component video output
B
GAME IN V
⇐
Composite video output
a
GAME IN L/R
⇐
Analog audio L/R output
b
DIGITAL IN OPTICAL 1 (GAME)
⇐
Digital optical output
b
B
Connection
A must be
assigned
(see
page 40)
a
A
L
OPTICAL
OUT
Y
PB
PR
COMPONENT VIDEO OUT
R
AUDIO
OUT
VIDEO
OUT
Game Console
31
Connecting the AV Receiver—Continued
Connecting a Camcorder or Other Device
Step 1: Video Connection
Make the connection A .
Step 2: Audio Connection
Make the connection a .
AUX INPUT
L AUDIO R
AUX INPUT
VIDEO
a
A
Camcorder, etc.
VIDEO
OUT
Connection
AV receiver
L AUDIO R
OUT
Signal flow
Camcorder etc.
A
AUX INPUT VIDEO
⇐
Composite video output
a
AUX INPUT L-AUDIO-R
⇐
Analog audio L/R output
Connecting a Portable Audio player
Step 1: Make the audio connection a .
Portable
Audio Player
AUX INPUT
PORTABLE
AUDIO LINE OUT
a
Connection
AV receiver
Signal flow
Portable Audio Player
a
AUX INPUT PORTABLE
⇐
Analog audio line output
Note:
When it is connected at the same time as AUX INPUT AUDIO L/R terminal, the input of PORTABLE is given priority
to and outputted.
32
Connecting the AV Receiver—Continued
Connecting a CD Player or Turntable
■ CD Player or Turntable (MM) with Built-in Phono Preamp
Step 1:
Choose a connection that matches your CD player ( a , b , or c ). Use connection a for a turntable with a built-in
phono preamp.
c
OPTICAL
2
(CD)
IN
b
L
L
R
R
1
(DVD/BD)
COAXIAL
Connect one or
the other Connection b must
be assigned
(see page 41)
AUDIO
OUTPUT
CD
IN
L
a
R
CD
L
OPTICAL COAXIAL
OUT
OUT
a
R
CD player
AUDIO
OUT
Turntable (MM) with
built-in phono preamp
• With connection a , you can listen to and record audio from the CD player and listen in Zone 2.
• To connect the CD player digitally, use connection b or c . (To record or listen in Zone 2 as well, use a and
b , or a and c .)
Connection
AV receiver
Signal flow
CD or turntable
a
CD IN L/R
⇐
Analog audio L/R output
b
DIGITAL IN COAXIAL 1 (DVD/BD)
⇐
Digital coaxial output
c
DIGITAL IN OPTICAL 2 (CD)
⇐
Digital optical output
■ Turntable (MM) with no Phono Preamp
Built-in
A phono preamp is necessary to connect a turntable that
doesn’t have a phono preamp built-in.
IN
AUDIO
OUTPUT
L
Phono preamp
L
R
■ Turntable with an MC (Moving Coil) Cartridge
An MC head amp and phono preamp are necessary to
connect a turntable with an MC (Moving Coil) cartridge.
R
CD
IN
L
L
R
R
CD
AUDIO
OUTPUT
AUDIO
INPUT
L
L
R
R
AUDIO
INPUT
AUDIO
OUTPUT
AUDIO
OUTPUT
L
L
R
R
Phono
preamp
MC head amp or
MC transformer
AUDIO
OUTPUT
AUDIO
INPUT
L
L
R
R
33
Connecting the AV Receiver—Continued
Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
Step 1:
Choose a connection that matches the recorder ( a , b or c ), and then make the connection.
c
OPTICAL
1
(GAME)
a
IN
L
b
R
COAXIAL
TV/TAPE
2
(CBL/SAT)
a
L
R
TV/TAPE
Connect one or the other
Connection b , c must be
assigned (see page 41)
L
OPTICAL
OUT
COAXIAL
OUT
R
AUDIO
IN
L
R
AUDIO
OUT
Cassette, CDR, MD, etc.
• With connection a , you can play and record and listen in Zone 2.
• To connect the recorder digitally for playback, use connections a and b , or a and c .
34
Connection
AV receiver
Signal flow
Cassette, CDR, MD, or DAT recorder
a
TV/TAPE IN L/R
TV/TAPE OUT L/R
⇐
⇒
Analog audio L/R output
Analog audio L/R input
b
DIGITAL IN COAXIAL 2 (CBL/SAT)
⇐
Digital coaxial output
c
DIGITAL IN OPTICAL 1 (GAME)
⇐
Digital optical output
Connecting the AV Receiver—Continued
Connecting an RI Dock
Not all iPod models output video. For information
about which iPod models are supported by the RI
Dock, see the RI Dock’s instruction manual.
■ If Your iPod Doesn’t Support Video:
Connect your RI Dock’s analog audio output jacks to
the AV receiver’s TV/TAPE IN L/R jacks. (Onkyo
DS-A2 hookup shown below.)
■ If Your iPod Supports Video:
Connect your RI Dock’s audio output jacks to the
AV receiver’s GAME IN or VCR/DVR IN L/R jacks,
and connect its video output jack to the AV receiver’s
GAME IN or VCR/DVR IN V jacks. (Onkyo DS-A2
hookup shown below.)
GAME
IN
L
R
TV/TAPE
VCR/DVR
V
V
IN
IN
IN
IN
L
L
R
R
VCR/DVR
GAME
Connect one
or the other
Notes:
• Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (see
page 88).
• Connect the RI Dock to the AV receiver with an u cable (see page 36).
• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.
• Set the AV receiver’s Input Display to “DOCK” (see page 44).
• See the RI Dock’s instruction manual for more information.
Connecting a Dock with the Universal Port connector
Note:
When UP-A1 series Dock that seated iPod is connected, the power consumption on standby mode slightly increases.
35
Connecting the AV Receiver—Continued
Connecting Onkyo u Components
IN
L
Step 1:
Make sure that each Onkyo component is connected
to the AV receiver with an analog audio cable (connection a in the hookup examples) (see pages 26 to
35).
Step 2:
Make the u connection (see illustration below).
R
CD
IN
L
REMOTE
CONTROL
R
DVD/BD
e.g., CD player
Step 3:
If you’re using an RI Dock, change the Input Display
(see page 44).
R
L
ANALOG
AUDIO OUT
e.g., DVD player
With u (Remote Interactive), you can use the following special functions:
■ Auto Power On/Standby
When you start playback on a component connected
via u, if the AV receiver is on Standby, it will automatically turn on and select that component as the
input source. Similarly, when the AV receiver is set
to Standby, all components connected via u will
also go on Standby.
■ Direct Change
When playback is started on a component connected
via u, the AV receiver automatically selects that
component as the input source.
■ Remote Control
You can use the AV receiver’s remote controller to
control your other u-capable Onkyo components,
pointing the remote controller at the AV receiver’s
remote control sensor instead of the component. You
must enter the appropriate remote control code first
(see page 89).
Notes:
• Use only u cables for u connections. u cables
are supplied with Onkyo players (DVD, CD, etc.).
• Some components have two u jacks. You can connect either one to the AV receiver. The other jack is for
connecting additional u-capable components.
• Connect only Onkyo components to u jacks. Connecting other manufacturer’s components may cause a
malfunction.
• Some components may not support all u functions.
Refer to the manuals supplied with your other Onkyo
components.
• While Zone 2 is on, the Auto Power On/Standby and
Direct Change u functions do not work.
36
R
L
ANALOG
AUDIO OUT
Connecting the Power Cord
Notes:
• Before connecting the power cord, connect all your
speakers and AV components.
• Plug the end of the power cord into a suitable wall outlet.
• Turning on the AV receiver may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the AV receiver into a different branch circuit.
Turning On the AV Receiver
ON/STANDBY
ON/STANDBY
STANDBY indicator
RECEIVER
Turning On and Standby
AV receiver
Remote
controller
or
Press the [ON/STANDBY] button.
Alternatively, press the remote controller’s [RECEIVER] button, followed
by the [ON/STANDBY] button.
The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
To turn the AV receiver off, press the [ON/STANDBY] button, or press the remote
controller’s [ON/STANDBY] button. The AV receiver will enter Standby mode. To
prevent any loud surprises when you turn on the AV receiver, always turn down the
volume before you turn it off.
Smooth Operation in a Few Easy Steps
To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the
very first time. These settings only need to be made once.
■ Do the 2EQ Room Correction and Speaker Setup—this is
essential!
See “Audyssey 2EQ™ Room Correction and Speaker Setup” on page 45.
■ Have you connected a component to an HDMI input,
component video input, or digital audio input?
If you have, see “HDMI Input Setup” on page 39, “Component Video
Setup” on page 40, or “Digital Input Setup” on page 41 respectively.
■ Have you connected an Onkyo RI Dock?
If you have, see “Changing the Input Display” on page 44.
HDMI
OUT
IN
TV/TAPE
RI Dock
37
First Time Setup
This section explains the settings that you need to make before using the AV receiver for the very first time.
Using the Display to change the
settings
RECEIVER
qwer
The settings of the AV receiver can be changed using the
Display.
1
Press the [RECEIVER] button followed by the [SETUP] button.
The main menu item appears on the
display.
2
Use the Up and Down [q]/[w] buttons to select main menu item
and then press [ENTER].
The submenu item appears on the
display.
Press the [SETUP] button to close the
menu.
Press the [RETURN] button to return to
the previous menu.
ENTER
SETUP
Using the Onscreen Setup Menus
Carry out the settings for the AV receiver by using the
Onscreen Setup Menu.
The onscreen setup menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to the composite video MONITOR OUT, or the COMPONENT VIDEO OUT, use the AV receiver’s display
when changing settings.
1
Press the [RECEIVER] button followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Menu
1. Input Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
Tip:
On several functions, the explanation
will be displayed under the screen.
2
38
Use the Up and Down [q]/[w] buttons to select main menu item
and then press [ENTER].
The submenu appears.
Press the [SETUP] button to close the
menu.
Press the [RETURN] button to return to
the previous menu.
Onscreen Setup Menus and Display
As each item in the Onscreen Setup Menus is selected,
the selected items will be displayed one by one.
Onscreen Setup Menus
Menu
1. Input Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
Display
Note:
During the Audyssey 2EQ™ Room Correction and
Speaker Setup, messages, etc., that are displayed on the
TV screen will appear in the Display.
First Time Setup—Continued
Video Input Setup
4
Use the Up and Down [q]/[w] buttons to select an input selector,
and use the Left and Right [e]/
[r] buttons to select:
HDMI1, HDMI2, HDMI3, HDMI4,
HDMI5:
Select the HDMI IN to which
the video component has
been connected.
- - - - -: Output composite video and
component video sources
from the HDMI OUT. The
video output signal from the
HDMI OUT is the one configured in “Component Video
Setup” (see page 40).
Each HDMI IN cannot be assigned to
more than one input selector. When
HDMI1 - HDMI5 have already been
assigned, you must set first any unused
input selectors to “- - - - -” or you will
be unable to assign HDMI1 - HDMI5
to input selector.
5
Press the [SETUP] button.
The setup menu closes.
HDMI Input Setup
If you connect a video component to HDMI IN, you
must assign that input to an input selector. For example,
if you connect your DVD/BD player to HDMI IN1, you
must assign HDMI IN1 to the DVD/BD input selector.
If you’ve connected your TV to the AV receiver with an
HDMI cable, you can set the AV receiver so that
composite video and component video sources are
upconverted* and output by the HDMI OUT. You can set
this for each input selector by selecting the “- - - - -”
option.
Composite video,
component video
HDMI
IN
OUT
Composite video,
component video
1
2
HDMI
Press the [RECEIVER] button followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Use the Up and Down [q]/[w] buttons to select “Input Assign”,
and then press [ENTER].
The “Input Assign” menu appears.
1. Input Assign
1. HDMI Input
2. Component Video Input
3. Digital Audio Input
3
Use the Up and Down [q]/[w] buttons to select “1. HDMI Input”,
and then press [ENTER].
The “HDMI Input” menu appears.
1–1. HDMI Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
TV/TAPE
TUNER
CD
PORT
Notes:
• For composite video and component video
upconversion for the HDMI OUT, the HDMI Input
setting must be set to “- - - - -”. See page 24 for more
information on video signal flow and upconversion.
• When an HDMI IN is assigned to an input selector as
explained here, the digital audio input for that input
selector is automatically set to the same HDMI IN.
See “Digital Input Setup” on page 41.
• The TUNER input selector cannot be assigned and is
fixed at the “- - - - -” option.
• If you connect an input component (such as UP-A1
series Dock that seated iPod) to the UNIVERSAL
PORT jack, you cannot assign any input to PORT
selector.
• Do not assign the component connected with the
HDMI input to the TV/TAPE selector when you set
“TV Control” setting to “On” (see page 79).
Otherwise, appropriate CEC (Consumer Electronics
Control) operation is not guaranteed.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
HDMI1
HDMI2
HDMI3
HDMI4
---------------------
39
First Time Setup—Continued
Component Video Setup
4
Use the Up and Down [q]/[w] buttons to select an input selector,
and then use the Left and Right
[e]/[r] buttons to select:
IN1: Select if the video component
is connected to COMPONENT VIDEO IN 1.
IN2: Select if the video component
is connected to COMPONENT VIDEO IN 2.
- - - - -: Select if you are using the
HDMI OUT, rather than the
COMPONENT VIDEO
OUT, for the output from
composite video and component video sources.
5
Press the [SETUP] button.
The setup menu closes.
If you connect to a COMPONENT VIDEO IN, you must
assign it to an input selector. For example, if you connect
your DVD/BD player to COMPONENT VIDEO IN 2,
you should assign it to the DVD/BD input selector.
Input selector
Default assignment
DVD/BD
IN1
VCR/DVR
-----
CBL/SAT
IN2
GAME
-----
AUX
-----
TV/TAPE
-----
TUNER
1
2
- - - - - (Fixed)
CD
-----
PORT
-----
Press the [RECEIVER] button followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Use the Up and Down [q]/[w] buttons to select “1. Input Assign”,
and then press [ENTER].
The “Input Assign” menu appears.
1. Input Assign
1. HDMI Input
2. Component Video Input
3. Digital Audio Input
3
Use the Up and Down [q]/[w] buttons to select “2. Component
Video Input”, and then press
[ENTER].
The “Component Video Input” menu
appears.
1–2. Component Video Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
TV/TAPE
TUNER
CD
PORT
40
IN1
----IN2
-------------------------
Notes:
• If you connect an input component (such as UP-A1
series Dock that seated iPod) to the UNIVERSAL
PORT jack, you cannot assign any input to PORT
selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
First Time Setup—Continued
Digital Input Setup
4
Use the Up and Down [q]/[w] buttons to select an input selector,
and use the Left and Right
[e]/[r] buttons to select
“COAX1”, “COAX2”, “OPT1”,
“OPT2”, or “- - - - - (analog)”.
• When an HDMI IN is assigned to an
input selector in “HDMI Input
Setup” on page 39, this input assignment is automatically set to the same
HDMI IN. And in addition to the
usual inputs (e.g., COAX1, COAX2,
etc.), you can also select HDMI
inputs.
• Press the [ENTER] button when you
do not use the signal of audio from
the HDMI IN. The “ * ” mark is displayed like “COAX1 * ”.
Examples:
If you connect your DVD/BD player to
the OPTICAL IN 1 jack, set “DVD/
BD” to “OPT1”.
If you want to listen to audio from the
component connected to the OPTICAL
IN 2 jack when the VCR/DVR input
selector is selected, set “VCR/DVR” to
“OPT2”.
If you want to listen to audio from the
component connected to the
COAXIAL IN 1 jack when the CBL/
SAT input selector is selected, set
“CBL/SAT” to “COAX1”.
For the input selector that you want to
listen the analog audio, set to “- - - - -”
in the Digital Audio Input setting and
HDMI Input setting (see page 39).
5
Press the [SETUP] button.
The setup menu closes.
If you connect a component to a digital input jack, you
must assign that jack to an input selector. For example, if
you connect your CD player to the OPTICAL IN1 jack,
you should assign that jack to the CD input selector. By
default, the COAXIAL IN1 jack is assigned to the DVD/
BD input selector, although this can be changed.
Here are the default assignments.
Input selector
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
TV/TAPE
TUNER
CD
PORT
Default assignment
COAX1
----COAX2
OPT1
--------- - - - - (Fixed)
OPT2
-----
1
Press the [RECEIVER] button followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [q]/[w] buttons to select “1. Input Assign”,
and then press [ENTER].
The “Input Assign” menu appears.
1. Input Assign
1. HDMI Input
2. Component Video Input
3. Digital Audio Input
3
Use the Up and Down [q]/[w] buttons to select “3. Digital Audio
Input”, and then press [ENTER].
The “Digital Audio Input” menu
appears.
1–3. Digital Audio Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
TV/TAPE
TUNER
CD
PORT
COAX 1
----COAX 2
OPT 1
------------OPT 2
-----
Notes:
• If you connect an input component (such as UP-A1
series Dock that seated iPod) to the UNIVERSAL
PORT jack, you cannot assign any input to PORT
selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
41
First Time Setup—Continued
Speaker Settings
4
Use the Up and Down [q]/[w] buttons to select “Speaker Type”,
and then use the Left and Right
[e]/[r] buttons to select:
Normal: Select this if you’ve connected your front speakers
normally.
Bi-Amp:Select this if you’ve connected your front speakers for
bi-amped operation.
Note:
Powered Zone 2 cannot be used if
“Speaker Type” is set to “Bi-Amp”.
5
Use the Up and Down [q]/[w] buttons to select “Surr Back/Front
High”, and then use the Left and
Right [e]/[r] buttons to select:
Front High:
Select this if you’ve connected your front high speakers to the SURR BACK L/R
terminal posts.
Surr Back:
Select this if you’ve connected your surround back
speakers to the SURR BACK
L/R terminal posts.
Note:
If the “Speaker Type” setting is set to
“Bi-Amp”, or “Powered Zone 2” is set
to “Not Act”, this setting cannot be
selected.
6
Press the [SETUP] button.
The setup menu closes.
If you change these settings, you must run the
Audyssey 2EQ™ Room Correction and Speaker Setup
again (see page 45).
If you’ve connected your front speakers to the FRONT
L/R and SURR BACK L/R terminal posts for bi-amping,
you must change the “Speaker Type” setting. For hookup
information, see “Bi-amping the Front Speakers” on
page 18.
Notes:
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the
volume.
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [q]/[w] buttons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
2. Speaker Setup
1.
2.
3.
4.
5.
3
Speaker Settings
Speaker Configuration
Speaker Distance
Level Calibration
Equalizer Settings
Use the Up and Down [q]/[w] buttons to select “1. Speaker Settings”, and then press [ENTER].
The “Speaker Settings” menu appears.
2–1. Speaker Settings
Speaker Type
Powered Zone 2
Surr Back/Front High
42
Normal
Not Act
Surr Back
Powered Zone 2
See “Zone 2” on page 82.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
First Time Setup—Continued
FM/AM Frequency Step Setup
For FM/AM tuning to work properly, you must specify
the FM/AM frequency step used in your area. Note that
when this setting is changed, all radio presets are
deleted.
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [q]/[w] buttons to select “7. Hardware
Setup”, and then press [ENTER].
The “Hardware Setup” menu appears.
5
Press the [SETUP] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
7. Hardware Setup
1. Remote ID
2. Tuner
3. HDMI
3
Use the Up and Down [q]/[w] buttons to select “2. Tuner”, and
then press [ENTER].
The “Tuner” menu appears.
7–2. Tuner
FM/AM Frequency Step
4
200kHz/10kHz
Use the Left and Right [e]/[r]
buttons to select:
200kHz/10kHz:
Select if 200 kHz/10 kHz steps are
used in your area.
50kHz/9kHz:
Select if 50 kHz/9 kHz steps are
used in your area.
43
First Time Setup—Continued
Changing the Input Display
If you connect an u-capable Onkyo RI Dock to the
TV/TAPE IN, GAME IN or VCR/DVR IN jacks, for u
to work properly, you must change this setting.
This setting can only be changed on the AV receiver.
GAME TV/TAPE
VCR/DVR
1
Press the [TV/TAPE], [GAME] or
[VCR/DVR] input selector button
so that “TV/TAPE”, “GAME” or
“VCR/DVR” appears on the display.
or
or
2
or
Press and hold down the [TV/
TAPE], [GAME] or [VCR/DVR]
input selector button (about 3
seconds) to change the setting.
Repeat this step to select DOCK.
For the TV/TAPE input selector, the
setting changes in this order:
or
44
→
→
TV/TAPE → MD → CDR
DOCK
For the GAME input selector, the
setting changes in this order:
GAME ↔ DOCK
For the VCR/DVR input selector, the
setting changes in this order:
VCR/DVR ↔ DOCK
Notes:
• DOCK can be selected for the TV/TAPE or GAME or
VCR/DVR input selector, but not at the same time.
• Enter the appropriate remote control code before
using the AV receiver’s remote controller for the first
time (see page 88).
First Time Setup—Continued
Audyssey 2EQ™ Room Correction
and Speaker Setup
With the supplied calibrated microphone,
Audyssey 2EQ automatically determines the number of
speakers connected, their size for purposes of bass
management, optimum crossover frequencies to the
subwoofer (if present), and distances from the primary
listening position.
Audyssey 2EQ then removes the distortion caused by
room acoustics by capturing room acoustical problems
over the listening area in both the frequency and time
domain. The result is clear, well-balanced sound for
everyone. Enabling Audyssey 2EQ allows you to also
use Audyssey Dynamic EQ™, which maintains the
proper octave-to-octave balance at any volume level (see
page 71).
Before using this function, connect and position all of
your speakers.
If Audyssey Dynamic EQ is set to “On”,
Audyssey Dynamic Volume™ becomes available.
About Audyssey Dynamic EQ
Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking
into account human perception and room acoustics.
Dynamic EQ selects the correct frequency response
and surround levels moment-by-moment at any userselected volume setting. The result is bass response,
tonal balance, and surround impression that remain
constant despite changes in volume. Dynamic EQ
combines information from incoming source levels
with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution.
Audyssey Dynamic EQ works in tandem with
Audyssey 2EQ to provide well-balanced sound for
every listener at any volume level.
About Audyssey Dynamic Volume
Audyssey Dynamic Volume solves the problem of
large variations in volume level between television
programs, commercials, and between the soft and loud
passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors
how the volume of program material is being perceived by listeners in real time to decide whether an
adjustment is needed. Whenever necessary, Dynamic
Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level
while optimizing the dynamic range.
Audyssey Dynamic EQ is integrated into Dynamic
Volume so that as the playback volume is adjusted
automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain
the same whether watching movies, flipping between
television channels, or changing from stereo to surround sound content.
Measurement Positions
To create a listening environment in your home theater
that all listeners will enjoy, Audyssey 2EQ takes
measurements at up to three positions within the
listening area.
a First measurement point
Also referred to as the Main Listening Position this
refers to the most central position where one would
normally sit within the listening environment. 2EQ
uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.
b Second measurement point
The right side of the listening area.
c Third measurement point
The left side of the listening area.
The distances between points a and b and points a
and c must be at least 1 meter.
From the examples below, choose the listening area that
best matches yours and place the microphone
accordingly when prompted.
TV
TV
TV
TV
TV
TV
TV
TV
TV
: Listening area
: Listening position
45
First Time Setup—Continued
Using Audyssey 2EQ™
2
ON/STANDBY
Set the speaker setup microphone at the Main Listening Position 1 (page 45), and connect it
to the SETUP MIC jack.
The speaker setting menu appears.
2EQ: Auto Setup
Speaker Type
Powered Zone 2
Surr Back/Front High
Normal
Not Act
Surr Back
Enter : Next
Speaker setup
microphone
If you change these settings, refer to
step 5 on “Speaker Settings” (page 42)
or step 4 on “Setting the Powered Zone
2” (page 83).
3
When you’ve finished, press the
[ENTER] button.
qwer
2EQ: Auto Setup
ENTER
Please place setup microphone at center
of listening area at ear height.
Next
Notes:
• If the AV receiver is muted, it will be unmuted
automatically when the Audyssey 2EQ Room
Correction and Speaker Setup starts.
• Room correction and speaker setup cannot be
performed while a pair of headphones is
connected.
• It takes about 15 minutes to complete the room
correction and speaker setup for three positions.
Total measurement time varies depending on the
number of speakers.
• Do not disconnect the speaker setup microphone
during the room correction and speaker setup,
unless you want to cancel the setup.
• Do not connect or disconnect any speakers during
the room correction and speaker setup.
The onscreen setup menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to the MONITOR OUT V or the COMPONENT
VIDEO OUT, use the AV receiver’s display when
changing settings.
1
46
Turn on the AV receiver and the
connected TV.
On the TV, select the input to which the
AV receiver is connected.
Notes:
• Before starting Audyssey 2EQ™
Room Correction and Speaker Setup,
arrange the room and connect the
speakers as you would for enjoying
movies. Changes to the room after
auto setup requires you run the auto
setup again, as room EQ
characteristics may have changed.
• When starting the room correction
and speaker setup, do not stand
between the speakers and
microphone, and avoid obstacles
blocking the path between speakers
and microphone. This will produce
inaccurate results.
• Position the microphone at ear height
of a seated listener with the
microphone tip pointed directly at
the ceiling using a tripod. Do not
hold the microphone in your hand
during measurements as this will
produce innacurate results.
First Time Setup—Continued
• Make the room as quiet as possible.
Background noise can disrupt the
room measurements. Close
windows, silence cell phones,
televisions, radios, air conditioners,
fluorescent lights, home appliances,
light dimmers, or other devices.
• Cell phones should be turned off or
placed away from all audio
electronics during the measurement
process as Radio Frequency
Interference (RFI) may cause
measurement disruptions (even if the
cell phone is not in use).
4
Press [ENTER].
The room correction and speaker setup
starts.
6
When prompted, place the setup
microphone at the next position,
and repeat step 5.
7
When the measurements are
complete, the following screen
appears.
2EQ: Auto Setup
Calculating...
8
When the calculations are complete, the following screen
appears.
2EQ: Auto Setup
2EQ: Auto Setup
Do not unplug setup mic.
Review Speaker Configuration
Please keep quiet.
Subwoofer
Front
Center
Surround
Front High
Surr Back
Surr Back Ch
Now measuring. . .
Use the Up and Down [q]/[w] buttons to select an option, and then
press [ENTER].
The options are:
Save:
Save the calculated settings and exit
the room correction and speaker
setup.
Cancel:
Cancel the room correction and
speaker setup.
Note:
You can view the calculated settings for
the speaker configuration, speaker distances, and speaker levels by using the
Left and Right [e]/[r] buttons.
The following screen appears.
2EQ: Auto Setup
Please place setup microphone at 2nd
of listening area at ear height.
Next
Place the setup microphone at
the next position (page 45), and
then press [ENTER].
Audyssey 2EQ performs more
measurements. This takes a few
minutes.
No
Full Band
80Hz
100Hz
150Hz
150Hz
2ch
Save
Cancel
Test tones are played through each
speaker as Audyssey 2EQ™ Room
Correction and Speaker Setup runs.
This process takes a few minutes.
Please refrain from talking during
measurements and do not stand
between speakers and the microphone.
5
:
:
:
:
:
:
:
9
If you selected “Save”, the results are
saved, and the following screen
appears.
2EQ: Auto Setup
2EQ: Auto Setup
Saving...
Do not unplug setup mic.
Please keep quiet.
Now measuring. . .
47
First Time Setup—Continued
10
Disconnect the speaker setup
microphone.
2EQ: Auto Setup
❏ Speaker Detect Error
This message appears if a speaker is not detected. “Yes”
means that a speaker was detected. “No” means that no
speaker was detected.
2EQ: Auto Setup
Speaker Detect Error
Please unplug setup microphone.
FL
SL
FHL
SBL
C
:
:
:
:
:
Yes
------Yes
FR
SR
FHR
SBR
SW
:
:
:
:
:
No
---------
Retry
Cancel
Notes:
• When the room correction and speaker setup is
complete, the “Equalizer Settings” (page 69) will be
set to “Audyssey” and the “Dynamic EQ” (page 71)
will be set to “On”.
• You can cancel the Room Correction and Speaker
Setup at any point in this procedure simply by
disconnecting the setup microphone.
One of the front speakers has not been detected.
2EQ: Auto Setup
Speaker Detect Error
FL
SL
FHL
SBL
C
:
:
:
:
:
Yes
------Yes
FR
SR
FHR
SBR
SW
:
:
:
:
:
Yes
No
-------
Retry
Cancel
Error Messages
While the room correction and speaker setup is in
progress, one of the following error messages may
appear:
One of the surround speakers has not been detected.
2EQ: Auto Setup
Speaker Detect Error
FL
SL
FHL
SBL
C
❏ Ambient noise is too high.
2EQ: Auto Setup
:
:
:
:
:
Yes
------Yes
FR
SR
FHR
SBR
SW
:
:
:
:
:
Yes
No
--Yes
---
Retry
Cancel
Ambient noise is too high.
Retry
Cancel
The surround back speakers have been detected but
the surround speakers haven’t.
2EQ: Auto Setup
Speaker Detect Error
This message appears if the background noise is too
loud and the measurements cannot be performed
properly.
Remove the source of the noise and try again.
Retry: Return to the measured point immediately
before and start set up again.
Cancel: Cancel the room correction and speaker setup.
FL
SL
FHL
SBL
C
:
:
:
:
:
Yes
----No
Yes
FR
SR
FHR
SBR
SW
:
:
:
:
:
Yes
Yes
--Yes
---
Retry
Cancel
The right surround back speaker has been detected
but the left surround back speaker hasn’t.
2EQ: Auto Setup
Speaker Detect Error
FL
SL
FHL
SBL
C
: Error
: Yes
: --: Yes
: Yes
FR
SR
FHR
SBR
SW
:
:
:
:
:
Yes
Yes
--Yes
Yes
Retry
Cancel
The speaker type detected does not match what was
expected. The speaker may be or incorrect type or
broken. Please check that it is the correct speaker
type, or that all drivers are working.
48
First Time Setup—Continued
❏ Speaker matching error!
2EQ: Auto Setup
Speaker matching error!
Retry
Cancel
The number of speakers detected on the second or
third measurement was different to the number
detected on the first measurement.
Make sure speakers that cannot be detected are
connected property.
Retry: Return to step 2 and try again.
Cancel: Cancel the room correction and speaker setup.
❏ Writing Error!
2EQ: Auto Setup
Writing Error!
Retry
Cancel
This message appears if saving fails.
Try saving again. If this message appears after 2 or 3
attempts, the AV receiver is probably malfunctioning.
Contact your Onkyo dealer.
Retry: Return to step 2 and try again.
Cancel: Cancel the room correction and speaker setup.
Changing the Speaker Settings Manually
If you wish to make changes to the settings found during
the room correction and speaker setup, follow the
directions on pages 67–69.
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by the Audyssey 2EQ™ Room Correction and
Speaker Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the subwoofer’s
volume to the half-way point, set it to its highest
crossover frequency, and then try running the
Audyssey 2EQ Room Correction and Speaker Setup
again. Note that if the volume is set too high and the
sound distorts, detection issues may occur, so use an
appropriate volume level. If the subwoofer has a lowpass filter switch, set it to Off or Direct. Refer to your
subwoofer’s instruction manual for details.
49
Basic Operations
Selecting the Input Source
This section explains how to select the input source (i.e., the AV component that you want to listen to or watch).
INPUT
SELECTOR
MASTER VOLUME
RECEIVER
VOL q/w
INPUT SELECTOR
1
AV receiver
Remote
controller
Use the AV receiver’s input selector buttons to select the input
source.
To select the input source with the remote controller, press the
[RECEIVER] button, and then press the INPUT SELECTOR buttons.
or
2
3
Start playback on the source component.
When you select DVD/BD or another video component, on your TV, you’ll
need to select the video input that’s connected to the AV receiver’s HDMI
OUT, COMPONENT VIDEO OUT or MONITOR OUT.
On some DVD/BD players, you may need to turn on the digital audio output.
AV receiver
Remote
controller
or
4
50
To adjust the volume, use the MASTER VOLUME control, or the
remote controller’s VOL [q]/[w] button.
The volume can be set to Min, 1 through 79, or Max.
The AV receiver is designed for home theater enjoyment. It has a wide volume
range, allowing precise adjustment.
Select a listening mode and enjoy!
See “Using the Listening Modes” on page 59.
Basic Operations—Continued
Displaying Source Information
–, +, TONE
You can display various information about the current
input source as follows.
Remote
controller
DISPLAY
Press the [RECEIVER] button,
and then press the [DISPLAY]
button repeatedly to cycle
through the available information.
Press
[RECEIVER]
first
Note:
This procedure can also be performed on the AV receiver
by using its [DISPLAY] button.
The following information can typically be displayed for
input sources.
Input source &
volume*1
Signal format*2
or sampling
frequency
DIMMER
Adjusting the Bass & Treble
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
1
AV receiver
Press the [TONE] button repeatedly to select either “Bass” or
“Treble”.
Input source &
listening mode
*1 When AM or FM radio is used, the band, preset number, and
frequency are displayed.
*2 If the input signal is analog, no format information is displayed.
If the input signal is PCM, the sampling frequency is displayed.
If the input signal is digital but not PCM, the signal format is
displayed.
Information is displayed for about three seconds, then the previously displayed information reappears.
Setting the Display Brightness
2
Use the TONE [–]/[+] buttons to
adjust.
You can adjust the brightness of the AV receiver’s display.
Remote
controller
■ Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
Press the [RECEIVER] button,
and then press the [DIMMER]
button repeatedly to select: dim,
dimmer, or normal brightness.
Alternatively, you can use the AV
receiver’s [DIMMER] button.
■ Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
Note:
This procedure can also be performed on the remote controller by using [AUDIO] button (see page 72).
51
Basic Operations—Continued
Using the Sleep Timer
Press
[RECEIVER]
first
MUTING
With the sleep timer, you can set the AV receiver to turn
off automatically after a specified period.
Press the [RECEIVER] button,
and then press the [SLEEP] button repeatedly to select the
required sleep time.
The sleep time can be set from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set. The specified sleep time appears on
the display for about five seconds, then
the previous display reappears.
SLEEP
If you need to cancel the sleep timer, press the [SLEEP]
button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the AV receiver sleeps,
press the [SLEEP] button. Note that if you press the
[SLEEP] button while the sleep time is being displayed,
you’ll shorten the sleep time by 10 minutes.
Muting the AV receiver
You can temporarily mute the output of the AV receiver.
Press the [RECEIVER] button,
and then press the [MUTING] button.
The output is muted and the MUTING
indicator flashes on the display, as
shown.
To unmute the AV receiver, press the
[MUTING] button again, or adjust the
volume.
The Mute function is cancelled when
the AV receiver is set to Standby.
52
Using Headphones
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the AV receiver’s PHONES jack for private listening, as shown.
Notes:
• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the PHONES
jack, the speakers are turned off. (The Powered Zone
2 speakers are not turned off.)
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, or Direct.
• Only the Stereo, Direct, and Mono listening modes
can be used with headphones (the listening modes
available also depend on the currently selected input
source).
Listening to the Radio
FM STEREO
AUTO
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
TUNED
TUNING MODE
■ Manual Tuning Mode
TUNER
TUNING /
1
Press the [TUNING MODE] button so that the AUTO indicator
disappears from the display.
2
Press and hold the TUNING Up or
Down [q]/[w] buttons.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
Listening to the Radio
Use the [TUNER] input selector
button to select either AM or FM.
In this example, FM has been selected.
Each time you press the [TUNER] button, the input source changes between
AM and FM.
Band
Frequency
(Actual display depends on country.)
Tuning into Radio Stations
■ Auto Tuning Mode
1
Press the [TUNING MODE] button so that the AUTO indicator
appears on the display.
2
Press the TUNING Up or Down
[q]/[w] buttons.
Searching stops when a station is
found.
This model changes FM/AM frequency in 200k/10k (or
50k/9k) Hz steps.
In Manual Tuning mode, FM stations will be in mono.
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
■ Tuning into Stations by Frequency
You can tune into AM and FM stations directly by entering the appropriate frequency.
1
Remote
controller
(Actual display depends on country.)
2
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator appears on the display, as shown.
Press the [TUNER] button repeatedly to select AM or FM, followed
by the [D.TUN] button.
Within 8 seconds, use the number buttons to enter the frequency of the radio station.
For example, to tune to 87.5 (FM),
press 8, 7, 5.
53
Listening to the Radio—Continued
Presetting AM/FM Stations
Selecting Presets
PRESET e/r
MEMORY
PRESET e/r
AV receiver
You can store a combination of up to 40 of your favorite
AM/FM radio stations as presets.
1
Tune into the AM/FM station that
you want to store as a preset.
2
Press the [MEMORY] button.
The preset number flashes.
3
While the preset number is flashing (about 8 seconds), use the
PRESET [e]/[r] buttons to
select a preset from 1 through 40.
4
Press the [MEMORY] button
again to store the station or
channel.
The station or channel is stored and the
preset number stops flashing.
Repeat this procedure for all of your
favorite AM/FM radio stations.
To select a preset, use the PRESET [e]/[r] buttons, or the
remote controller’s CH [+/–] button.
Remote
controller
You can also use the remote controller’s number buttons to select
a preset directly.
Deleting Presets
MEMORY, TUNING MODE
Note:
You can name your radio presets for easy identification
(see page 76). Its name is displayed instead of the band
and frequency.
54
1
Select the preset that you want to
delete.
See the previous section.
2
While holding down the [MEMORY] button, press the [TUNING
MODE] button.
The preset is deleted and its number
disappears from the display.
UP-A1 series Dock for iPod
About the UP-A1 series Dock
With the UP-A1 series Dock, you can easily play the
music, photo, or movie stored on your Apple iPod
through the AV receiver and enjoy great sound. You can
use the AV receiver’s remote controller to operate your
iPod.
For the latest information on the Dock, see the Onkyo
Web site at: www.onkyo.com
■ Adjusting the Adapter
The adapter needs to be adjusted to match your particular iPod. If there’s a gap between the back of your iPod
and the adapter, turn the adapter counterclockwise to
close the gap. Turning the adapter counterclockwise
moves it forward. Turning it clockwise moves it backward.
Forward
Adapter
Backward
Dock connector
Compatible iPod models
For information about which iPod models are supported by the UP-A1 series Dock, see the UP-A1 series
Dock’s instruction manual.
Note:
Before using the UP-A1 series Dock, update your iPod
with the latest software, available from the Apple Web
site.
Notes:
• Make sure that the output level of the AV receiver is
set to minimum.
• To prevent damage to the dock connector, don’t twist
your iPod when inserting or removing it, and be careful not to knock over the dock while your iPod is
inserted.
• Do not take off your iPod from the Dock when you
play back the music, photo, or movie stored on your
iPod.
• Don’t use the UP-A1 with any other iPod accessories,
such as FM transmitters and microphones, because
they may cause a malfunction.
• It is recommended that you update your iPod software
before using it with this unit. The updater for the iPod
software is available at the Apple website.
Putting Your iPod in the Dock
1 Turn on the AV receiver, and select the [PORT]
selector.
2 Align your iPod with the Dock connector and push
it down so that it’s fully seated.
Remove iPod
case before
inserting
Function Overview
■ Basic Operation
Note:
The AV receiver may take several seconds to startup, so
you might not hear the first few seconds of the first song.
• Auto Power On Function
If you start iPod playback while the AV receiver is
on Standby, the AV receiver will automatically turn
on and select your iPod as the input source. Then,
your iPod will start playback.
• Direct Change Function
If you start iPod playback while listening to another
input source, the AV receiver will automatically
select your iPod as the input source.
• Using the AV receiver’s Remote Controller
You can use the AV receiver’s remote controller to
control basic iPod functions.
55
UP-A1 series Dock for iPod—Continued
Operating Notes:
• Before selecting a different input source, stop iPod
playback to prevent the AV receiver from selecting the
iPod input source by mistake.
• If any accessories are connected to your iPod, the AV
receiver may not be able to select the input source
properly.
• While your iPod is in the UP-A1 series Dock, its volume control has no effect. If you adjust your iPod
models volume control while it’s in the UP-A1 series
Dock, make sure it’s not set too high before you reconnect your headphones.
■ Using Your iPod models Alarm Clock
You can use your iPod models Alarm Clock function to
automatically turn on your iPod and the AV receiver at a
specified time. The AV receiver’s input source will automatically be set to the [PORT] selector.
Notes:
• To use this function, your iPod must be in the UP-A1
series Dock, and the UP-A1 series Dock must be connected to the AV receiver.
• When you use this function, be sure to set the AV
receiver’s volume control to a suitable level.
• The AV receiver may take several seconds to startup,
so you might not hear the first few seconds of the first
song.
■ Charging Your iPod models Battery
The UP-A1 series Dock charges your iPod models battery while your iPod is in the UP-A1 series Dock and
connected to the UNIVERSAL PORT jacks on the AV
receiver. While your iPod is seated in the UP-A1 series
Dock, its battery will be charged when the AV receiver is
set to “On” or “Standby”.
Note:
When UP-A1 series Dock that seated iPod is connected,
the power consumption on standby mode slightly
increases.
Controlling iPod
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
Dock, you can control your iPod in the Dock with the
following buttons.
The [PORT] button is preprogrammed with the remote
control code for controlling a Dock with Universal Port
connector.
For details on entering a remote control code, see
page 88.
When Using a Dock with Universal Port connector:
• Connect the Dock to the UNIVERSAL PORT jack.
• See to the Dock’s instruction manual for more information.
You can control your iPod when “PORT” is selected as
the input source.
Press [PORT] button first
f
g
h
i
a
b
c
d
j
k
l
m
n
e
o
Note:
For detailed operation of the iPod, please refer to the
instruction manual.
56
UP-A1 series Dock for iPod—Continued
a Arrow [q]/[w] and ENTER buttons
Used to navigate menus and select items.
b Previous [7] button
Restarts the current song. Press it twice to select the
previous song.
Status messages
❏ The AV receiver is checking the connection
with the dock
c Rewind [5] button
Press and hold to rewind.
d Pause [3] button
Pauses playback.
❏ The AV receiver does not support the
connected dock
e REPEAT button
Used with the repeat function.
f MUTING button (52)
Mutes or unmutes the AV receiver.
❏ UP-A1 series Dock is connected
g ALBUM +/– button
Selects the next or previous album.
h VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver.
i PLAYLIST [e]/[r] buttons
Selects the previous or next playlist on the iPod.
j RETURN button
Exits the menu or returns to the previous menu.
k Play [1] button
Starts playback. If the component is off, it will turn
on automatically.
l Next [6] button
Selects the next song.
m Fast Forward [4] button
Press and hold to fast forward.
n Stop [2] button
Stops playback and displays a menu.
Your iPod is properly stationed in a UP-A1 series Dock
connected to the UNIVERSAL PORT jack of this unit,
and the connection between your iPod and this unit is
complete.
When connection is confirmed, “UP-A1” is displayed
for about 8 seconds.
❏ Dock is not connected
Your iPod was removed from a UP-A1 series Dock connected to the UNIVERSAL PORT jack of this unit.
Note:
When the status message is not displayed on the AV
receiver’s display, check the connection to your iPod.
o RANDOM button
Used with the shuffle function.
57
Recording
This section explains how to record the selected input
source to a component with recording capability, and
how to record audio and video from different sources.
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• Only analog inputs can be recorded.
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
AV Recording
Recording Separate AV Sources
Here you can record audio and video from completely
separate sources, allowing you to overdub audio onto
your video recordings. This function takes advantage of
the fact that when an audio-only input source (i.e., TV/
TAPE, CD) is selected, the video input source remains
unchanged.
In the following example, audio from the CD player connected to the CD IN, and video from the camcorder connected to the AUX INPUT VIDEO jack are recorded by
the VCR connected to the VCR/DVR OUT jacks.
Audio sources can be recorded to a recorder (e.g., cassette deck, CDR, MD) connected to the TV/TAPE OUT
jack. Video sources can be recorded to a video recorder
(e.g., VCR, DVD recorder) connected to the VCR/DVR
OUT jack. See page 29 or 34 for hookup information.
58
1
Use the input selector buttons to
select the source that you want
to record.
You can watch the source while recording. The AV receiver’s MASTER VOLUME control has no effect on
recording.
2
On your recorder, start recording.
3
On the source component, start
playback.
If you select another input source during recording, that input source will be
recorded.
Camcorder
video signal
audio signal
CD player
VCR
1
Prepare the camcorder and CD player for
playback.
2
Prepare the VCR for recording.
3
Press the [AUX] input selector button.
4
Press the [CD] input selector button.
This selects the CD player as the audio source, but
leaves the camcorder as the video source.
5
Start recording on the VCR and start playback on the camcorder and CD player.
The video from the camcorder and the audio from
the CD player are recorded by the VCR.
Using the Listening Modes
Selecting Listening Modes
Selecting with the Remote Controller
See “About the Listening Modes” on page 64 for
detailed information about the listening modes.
• The Dolby Digital and DTS listening modes can
only be selected if your DVD/BD player is connected to the AV receiver with a digital audio
connection (coaxial, optical, or HDMI).
• The listening modes you can select depends on
the format of the input signal. To check the format, see “Displaying Source Information” on
page 51.
• While a pair of headphones is connected, you
can only select the Mono, Direct, or Stereo listening mode.
MUSIC
MOVIE/TV
GAME
STEREO
Press the [RECEIVER] button,
and then press the LISTENING
MODE button repeatedly to
select the listening mode.
Selecting on the AV receiver
LISTENING MODE buttons
■ LISTENING MODE buttons
[MOVIE/TV] button
This button selects the listening modes intended for
use with movies and TV.
[MUSIC] button
This button selects the listening modes intended for
use with music.
■ LISTENING MODE buttons
[MOVIE/TV] button
This button selects the listening modes intended for
use with movies and TV.
[MUSIC] button
This button selects the listening modes intended for
use with music.
[GAME] button
This button selects the listening modes intended for
use with video games.
[STEREO] button
This button selects the Stereo listening mode and All
Channel Stereo listening mode.
[GAME] button
This button selects the listening modes intended for
use with video games.
59
Using the Listening Modes—Continued
Listening Modes Available for Each Source Format
The Speaker layout illustration shows which
speakers are set to active in the “Speaker Configuration” setting (see page 67) and the
“Speaker Type” setting (see page 42).
Front high
L Speaker
FHL
Front L Speaker
FL
Front high
R Speaker
FHR
C
Front R
Speaker
FR
Center Speaker
Subwoofer
SW
The LISTENING MODE button illustration
shows that listening modes can be selected.
Surround R
Speaker
Surround back
Surround back
R Speaker
SBL
SBR
L Speaker C : active in the speaker settings
C : non-active in the speaker settings
SR
SL
Surround L
Speaker
Mono/Multiplex Sources
✔: Available Listening Modes
Speaker layout
FHL
FL
Listening Mode
FHR
FHL
FR
FL
C
Button
FHR
FHL
FR
FL
C
SW
SBL
SBR
FHL
FR
FL
SW
SR
SL
FHR
C
SBL
SBR
SW
SR
SL
SBL
SBR
SR
SL
SBL
✔
✔
✔
✔
Stereo
✔
✔
✔
✔
Mono
✔
✔
✔
✔
Orchestra
✔
✔*1
Unplugged
✔
✔*1
Studio-Mix
✔
✔*1
TV Logic
✔
✔*1
Game-RPG
✔
✔*1
Game-Action
✔
✔*1
Game-Rock
✔
✔*1
Game-Sports
✔
✔*1
AllChStereo
✔
✔
✔*1
FullMono
✔
✔
✔*1
✔
✔
✔
✔
Notes:
*1 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 73.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz.
• The listening modes cannot be selected with some source formats.
60
SBR
Direct
T-D (TheaterDimensional)
FR
SW
SR
SL
FHR
C
Using the Listening Modes—Continued
Stereo Source
✔: Available Listening Modes
Speaker layout
FHL
FL
Listening Mode
FHR
FHL
FR
FL
C
Button
FHR
FHL
FR
FL
C
SW
SBL
SBR
FHL
FR
FL
SW
SR
SL
FHR
C
SBL
SBR
FR
SW
SR
SL
FHR
C
SW
SR
SL
SBL
SBR
SR
SL
SBL
SBR
Direct
✔
✔
✔
✔
Stereo
✔
✔
✔
✔
Mono
✔
✔
✔
✔
✔
✔
✔ (Surround Back)
✔
✔
✔ (Surround Back)
✔
✔
✔ (Surround Back)
PLII/PLIIx
Movie*2
PLII/PLIIx
Music*2
PLII/PLIIx
Game*2
✔ (Front High)
PLIIz Height
Neo:6 Cinema
✔
✔
✔ (Surround Back)
Neo:6 Music
✔
✔
✔ (Surround Back)
Orchestra
✔
✔*1
Unplugged
✔
✔*1
Studio-Mix
✔
✔*1
TV Logic
✔
✔*1
Game-RPG
✔
✔*1
Game-Action
✔
✔*1
Game-Rock
✔
✔*1
Game-Sports
✔
✔*1
AllChStereo
✔
✔
✔*1
FullMono
✔
✔
✔*1
✔
✔
✔
T-D (TheaterDimensional)
✔
Notes:
*1 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 73.
*2 If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz.
• The listening modes cannot be selected with some source formats.
61
Using the Listening Modes—Continued
5.1 channel Sources
✔: Available Listening Modes
Speaker layout
FHL
FL
Listening Mode
FHR
FHL
FR
FL
C
Button
FHR
FHL
FR
FL
C
SW
SBL
SBR
FHL
FR
FL
SW
SR
SL
FHR
C
SBL
SBR
SW
SR
SL
SBL
SBR
SR
SL
SBL
SBR
Direct
✔
✔
✔
✔
Stereo
✔
✔
✔
✔
Mono
✔
✔
✔
✔
✔
✔
✔
DolbyDigital/
DolbyDigital
Plus/TrueHD/
Multichannel/
DTS/DTS-HD
High
Resolution
Audio/DTS-HD
Master Audio/
DTS Express/
FR
SW
SR
SL
FHR
C
DSD*2
Neo:6
✔ (Surround Back)
PLIIx Movie
✔ (Surround Back)
PLIIx Music
✔ (Surround Back)
✔ (Front High)
PLIIz Height
✔ (Surround Back)
DolbyEX
Orchestra
✔
✔*1
Unplugged
✔
✔*1
Studio-Mix
✔
✔*1
TV Logic
✔
✔*1
Game-RPG
✔
✔*1
Game-Action
✔
✔*1
Game-Rock
✔
✔*1
Game-Sports
✔
✔*1
AllChStereo
✔
✔
✔*1
FullMono
✔
✔
✔*1
✔
✔
✔
T-D (TheaterDimensional)
✔
Notes:
*1 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 73.
*2 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound
according to the player. In that case, set the output setting on the player side to PCM.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz.
• The listening modes cannot be selected with some source formats.
62
Using the Listening Modes—Continued
7.1 channel Sources
✔: Available Listening Modes
Speaker layout
FHL
FL
Listening Mode
FHR
FHL
FR
FL
C
Button
FHR
FHL
FR
FL
C
SW
SBL
SBR
FHL
FR
FL
SW
SR
SL
FHR
C
SBL
SBR
FR
SW
SR
SL
FHR
C
SW
SR
SL
SBL
SBR
SR
SL
SBL
SBR
✔*2
Direct
✔
✔
✔
Stereo
✔
✔
✔
✔
Mono
✔
✔
✔
✔
✔
✔
✔*2
(Surround Back)
Multichannel/
DolbyDigital
Plus/TrueHD/
DTS-HD High
Resolution
Audio/DTS-HD
Master Audio
(Surround Back)
✔ (Front High)
PLIIz Height
Orchestra
✔
✔*1
Unplugged
✔
✔*1
Studio-Mix
✔
✔*1
TV Logic
✔
✔*1
Game-RPG
✔
✔*1
Game-Action
✔
✔*1
Game-Rock
✔
✔*1
Game-Sports
✔
✔*1
AllChStereo
✔
✔
✔*1
FullMono
✔
✔
✔*1
✔
✔
✔
T-D (TheaterDimensional)
✔
DTS-ES Discrete/Matrix Sources
DTS-ES
Discrete
✔ (Surround Back)
DTS-ES Matrix
✔ (Surround Back)
Notes:
*1 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 73.
*2 When the input source contains the encoded front high channel, front high speakers output the sound.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz.
• The listening modes cannot be selected with some source formats.
63
Using the Listening Modes—Continued
About the Listening Modes
The AV receiver’s listening modes can transform your
listening room into a movie theater or concert hall, with
high fidelity and stunning surround sound.
Direct
In this mode, audio from the input source is output
directly with minimal processing, providing high-fidelity reproduction. All of the source’s audio channels are
output as they are.
Stereo
Sound is output by the front left and right speakers and
subwoofer.
Mono
Use this mode when watching an old movie with a mono
soundtrack, or use it with the foreign language
soundtracks recorded in the left and right channels of
some movies. It can also be used with DVDs or other
sources containing multiplexed audio, such as karaoke
DVDs.
Multichannel
This mode is for use with PCM multichannel sources.
Dolby Pro Logic IIx
Dolby Pro Logic II
Dolby Pro Logic IIx expands any 2-channel source for
7.1-channel playback. It provides a very natural and
seamless surround-sound experience that fully envelops
the listener. As well as music and movies, video games
can also benefit from the dramatic spatial effects and
vivid imaging. If you’re not using any surround back
speakers, Dolby Pro Logic II will be used instead of
Dolby Pro Logic IIx.
• Dolby PLIIx Movie
Use this mode with any stereo or Dolby Surround
(Pro Logic) movie (e.g., TV, DVD, VHS).
• Dolby PLIIx Music
Use this mode with any stereo or Dolby Surround
(Pro Logic) music source (e.g., CD, radio, cassette,
TV, VHS, DVD).
• Dolby PLIIx Game
Use this mode with video games, especially those
that bear the Dolby Pro Logic II logo.
Dolby Pro Logic IIz Height
Dolby Pro Logic IIz Height is designed to more effectively use existing program material when height channel speaker outputs are present. Dolby Pro Logic IIz
Height can be used to upmix a variety of sources from
movies and music, but are particularly well-suited to
upmix game content.
Dolby Digital
Use this mode with DVDs that bear the Dolby Digital
logo, and Dolby Digital TV broadcasts. This is the most
common digital surround-sound format, and it’ll put you
right in the middle of the action, just like being in a
movie theater or concert hall.
64
5.1-channel source + Dolby EX
These modes expand 5.1-channel sources for 6.1/7.1channel playback. They’re especially suited to Dolby EX
soundtracks that include a matrix-encoded surround
back channel. The additional channel adds an extra
dimension and provides an enveloping surround sound
experience, perfect for rotating and fly-by sound effects.
Dolby Digital Plus
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest multichannel audio format from Dolby. It supports up to 7.1
channels with 48 kHz sampling rate.
Dolby TrueHD
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc formats, this new Dolby format offers up to 7.1 discrete
channels of digital audio with 48/96 kHz, up to 5.1-channels with 192 kHz sampling rate.
5.1-channel source + Dolby PLIIx Music
These modes use the Dolby Pro Logic IIx Music mode
to expand 5.1-channel sources for 6.1/7.1-channel playback.
5.1-channel source + Dolby PLIIx Movie
These modes use the Dolby Pro Logic IIx Movie mode
to expand 5.1-channel sources for 7.1-channel playback.
DTS
The DTS digital surround-sound format supports up to
5.1 discrete channels and uses less compression for highfidelity reproduction. Use it with DVDs and CDs that
bear the DTS logo.
DTS 96/24
This mode is for use with DTS 96/24 sources. This is
high-resolution DTS with a 96 kHz sampling rate and
24-bit resolution, providing superior fidelity. Use it with
DVDs that bear the DTS 96/24 logo.
DTS-ES Discrete
This mode is for use with DTS-ES Discrete soundtracks,
which use a discrete surround back channel for true 6.1/
7.1-channel playback. The seven totally separate audio
channels provide better spatial imaging and 360-degree
sound localization, perfect for sounds that pan across the
surround channels. Use it with DVDs that bear the DTSES logo, especially those with a DTS-ES Discrete
soundtrack.
DTS-ES Matrix
This mode is for use with DTS-ES Matrix soundtracks,
which use a matrix-encoded back-channel for 6.1/7.1channel playback. Use it with DVDs that bear the DTSES logo, especially those with a DTS-ES Matrix
soundtrack.
Using the Listening Modes—Continued
DTS Neo:6
This mode expands any 2-channel source for up to 7.1channel playback. It uses seven full-bandwidth channels
of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.
• Neo:6 Cinema
Use this mode with any stereo movie (e.g., TV,
DVD, VHS).
• Neo:6 Music
Use this mode with any stereo music source (e.g.,
CD, radio, cassette, TV, VHS, DVD).
5.1-channel source + Neo:6
This mode uses Neo:6 to expand 5.1-channel sources for
6.1/7.1-channel playback.
DTS-HD High Resolution Audio
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest multichannel audio format from DTS. It supports up to 7.1
channels with 96 kHz sampling rate.
DTS-HD Master Audio
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc formats, this new DTS format offers up to 7.1 discrete channels of digital audio with 48/96 kHz, up to 5.1-channels
with 192 kHz sampling rate.
DTS Express
This format supports up to 5.1 channels and a lower sampling rate of 48 kHz. Applications include interactive
audio and commentary encoding for HD DVD Sub
Audio and Blu-ray Secondary Audio. Also broadcast
and media servers.
DSD
DSD stands for Direct Stream Digital and is the format
used to store digital audio on Super Audio CDs (SACD).
This mode can be used with SACDs that feature multichannel audio.
Onkyo Original DSP Modes
Orchestra
Suitable for classical or operatic music, this mode
emphasizes the surround channels in order to widen the
stereo image, and simulates the natural reverberation of
a large hall.
Unplugged
Suitable for acoustic instruments, vocals, and jazz, this
mode emphasizes the front stereo image, giving the
impression of being right in front of the stage.
Studio-Mix
Suitable for rock or pop music, listening to music in this
mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.
TV Logic
This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire
sound, and clarity to voices.
Game-RPG
Use this mode when playing role playing game discs.
Game-Action
Use this mode when playing action game discs.
Game-Rock
Use this mode when playing rock game discs.
Game-Sports
Use this mode when playing sports game discs.
All Ch Stereo
Ideal for background music, this mode fills the entire listening area with stereo sound from the front, surround,
and surround back speakers.
Full Mono
In this mode, all speakers output the same sound in
mono, so the sound you hear is the same regardless of
where you are within the listening room.
T-D (Theater-Dimensional)
With this mode you can enjoy a virtual surround sound
even with only two or three speakers. This works by controlling how sounds reach the listener’s left and right
ears. Good results may not be possible if there’s too
much reverb, so we recommend that you use this mode
in an environment with little or no natural reverb.
65
Advanced Setup
Onscreen Setup Menus
The onscreen setup menus appear on the connected TV and provide a convenient way to change the AV receiver’s
various settings. Settings are organized into nine categories on the main menu, most containing a submenu.
Main menu
Submenus
pages 39–41
Menu
1. Input Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
1. Input Assign
1. HDMI Input
2. Component Video Input
3. Digital Audio Input
pages 67–69
2. Speaker Setup
1.
2.
3.
4.
5.
page 77
6. Miscellaneous
Speaker Settings
Speaker Configuration
Speaker Distance
Level Calibration
Equalizer Settings
1. Volume Setup
2. OSD Setup
page 42
pages 70–71
3. Audio Adjust
1.
2.
3.
4.
5.
pages 78–79
7. Hardware Setup
1. Remote ID
2. Tuner
3. HDMI
Multiplex / Mono
Dolby
DTS
Audyssey
Theater-Dimensional
pages 75–76
page 43
4. Source Setup
— DVD/BD —
page 86
1. IntelliVolume
2. A/V Sync
3. Name Edit
8. Remote Controller Setup
1. Remote Mode Setup
page 74
5. Listening Mode Preset
page 80
9. Lock Setup
Lock
66
Unlocked
1.
2.
3.
4.
5.
6.
7.
8.
9.
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
TV/TAPE
TUNER
CD
PORT
Advanced Setup—Continued
Common Procedures in Setup Menu
1
Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
2
Use the Up and Down [q]/[w] buttons to
select main menu, and then press
[ENTER].
3
Use the Up and Down [q]/[w] buttons to
select the function, and then press
[ENTER].
4
Use the Up and Down [q]/[w] buttons to
select setting, and then use the Left and
Right [e]/[r] buttons to set them.
5
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
RECEIVER
qwer
ENTER
SETUP
Speaker Setup
Some of the settings in this section are set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup
function (see page 45).
Here you can check the settings made by the Audyssey 2EQ Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the connected speakers after using the Audyssey 2EQ Room Correction
and Speaker Setup function.
Note:
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
Speaker Settings
See “Speaker Settings” on page 42.
Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify
“Full Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good
sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be
output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover
frequencies.
Subwoofer
Yes: Select if a subwoofer is connected (default).
No: Select if no subwoofer is connected.
Front*1
Full Band, 40Hz to 100Hz (default), 120Hz, 150Hz, 200Hz
Center*2
Full Band, 40Hz to 100Hz, 120Hz, 150Hz, 200Hz
None: Select if no speaker is connected.
Surround*2
Front High*2*3*5*6
Surr Back*3*4*5*7
Surr Back CH*8
1ch: Select if only one surround back L speaker is connected.
2ch: Select if two (left and right) surround back speakers are connected (default).
67
Advanced Setup—Continued
LPF of LFE
80Hz, 90Hz, 100Hz (default), 120Hz
(Low-Pass Filter for the LFE Channel)
This setting is not set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function (see
page 45).
With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
Double Bass*9
This setting is not set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see
page 45).
With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
On: Double Bass function on (default).
Off: Double Bass function off.
Notes:
*1
*2
*3
*4
*5
*6
*7
*8
*9
If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.
If the “Front” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.
If the “Surround” setting is set to “None”, this setting cannot be selected.
If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.
If the “Speaker Type” setting is set to “Bi-Amp” (page 42), or Powered Zone 2 is being used (page 83), this setting cannot be
selected.
If the “SurrBack/FrontHigh” setting is set to “SurrBack” (page 42), this setting cannot be selected.
If the “SurrBack/FrontHigh” setting is set to “FrontHigh” (page 42), this setting cannot be selected.
If the “Surr Back” Setting is set to “None” (page 67), this setting cannot be selected.
This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “Full Band”.
Speaker Distance
This setting is set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 45).
Here you can specify the distance from each speaker to the listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer intended.
Unit
feet: Distances can be set in feet. Range: 1 to 30 feet in 1-foot steps.
meters: Distances can be set in meters. Range: 0.3 to 9 meters in 0.3-meter steps.
Left, Front High Left, Center, Front High Right, Right, Surr Right, Surr Back R,
Surr Back L, Surr Left, Subwoofer
Specify the distance from the each speaker to your listening position.
Note:
Speakers that you set to “No” or “None” in the Speaker Configuration (page 67) cannot be selected.
Notes:
• The Center, Subwoofer and Front High distances can be set up to 5 ft. (1.5 m) more or less than the Left distance.
For example, if the Left distance is set to 20 ft. (6 m), the Center, Subwoofer, Front High Left and Front High Right
distances can be set between 15 and 25 ft. (4.5 and 7.5 m).
• The Surround and Surround Back distances can be set up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the Left
distance. For example, if the Left distance is set to 20 ft. (6 m), the Surr Right, Surr Left, Surr Back R, and Surr
Back L distances can be set between 5 and 25 ft. (1.5 and 7.5 m).
68
Advanced Setup—Continued
Level calibration
This setting is set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function (see page 45).
Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same
at the listening position.
Left, Front High Left, Center, Front High Right, Right, Surr Right, Surr Back R,
Surr Back L, Surr Left, Subwoofer
The levels can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).
Note:
Speakers that you set to “No” or “None” in the “Speaker Configuration” (page 67) do not output the test tone.
Note:
The speakers cannot be calibrated while the output of the AV receiver is muted.
Tip:
If you’re using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening
position, measured with C-weighting and slow reading.
Equalizer Settings
This setting is set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 45).
With the Equalizer settings, you can adjust the tone of speakers individually with a 5-band equalizer. The volume of
each speaker can be set on page 69.
Notes:
• You can select: “63Hz”, “250Hz”, “1000Hz”, “4000Hz”, or “16000Hz”. And for the subwoofer, “25Hz”, “40Hz”,
“63Hz”, “100Hz”, or “160Hz”.
• While the Direct listening mode is selected, the equalizer settings have no effect.
Equalizer
Manual: You can adjust the equalizer for each speaker manually. If you selected “Manual”,
continue with this procedure.
1
Press the Down [w] button to select “Channel”, and then use the
Left and Right [e]/[r] buttons to select a speaker.
2
Use the Up and Down [q]/[w] buttons to select a frequency, and
then use the Left and Right [e]/[r] buttons to adjust the level at
that frequency.
The volume at each frequency can be adjusted from –6 to +6 dB in 1 dB
steps.
Tip:
Low frequencies (e.g., 63Hz) affect bass sounds; high frequencies (e.g.,
16000Hz) affect treble sounds.
3
Use the Up [q] button to select “Channel”, and then use the Left
and Right [e]/[r] buttons to select another speaker.
Repeat steps 1 and 2 for each speaker.
Speakers that you set to “No” or “None” in the Speaker Configuration
(page 67) cannot be selected.
Audyssey:The tone for each speaker is set automatically by the Audyssey 2EQ Room
Correction and Speaker Setup function. Be sure to select this setting after having
performed the Room Correction and Speaker Setup. “Dynamic EQ” and “Dynamic
Volume” become available (see page 71).
Off: Tone off, response flat (default).
69
Advanced Setup—Continued
Audio Adjust
With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.
Multiplex/Mono Settings
Multiplex
Input Channel
Main: The main channel is output (default).
Sub: The sub channel is output.
Main/Sub: Both the main and sub channels are output.
This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or
languages with multiplex sources, multilingual TV broadcasts, and so on.
Mono
Input Channel
L+R: Both the left and right channels are output (default).
Left: Only the left channel is output.
Right: Only the right channel is output.
This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or
2-channel analog/PCM source in the Mono listening mode.
Dolby Settings
PLIIx Music (2ch Input)
These settings apply to only 2-channel stereo sources.
If you’re not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx.
Panorama
On: Panorama function on.
Off: Panorama function off (default).
With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx
Music listening mode.
Dimension
–3 to +3 (default: 0)
With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music
listening mode. Higher settings move the sound field backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve
the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move
it backward.
Center Width
0 to 7 (default: 3)
With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output by only
the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front
left and right speakers to create a phantom center.) This setting controls the front left, right, and center mix,
allowing you to adjust the weight of the center channel sound.
Dolby EX
Dolby EX
Auto: If the source signal contains a Dolby EX flag, the Dolby EX listening mode is
used.
Manual: You can select any available listening mode (default).
This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround
back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD
only.
Notes:
• If the “Surr Back” Setting is set to “None” (page 67), this setting cannot be selected.
• If the “Front High” Setting is set to other than “None”, this setting is fixed at “Manual” (page 67).
70
Advanced Setup—Continued
DTS Setting
Neo:6 Music
Center Image
0 to 5 (default: 2)
The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With
this setting, you can specify by how much the front left and right channel output is attenuated in order to create
the center channel.
Setting a value [0] in the middle is set to hear a sound. Sound is spread in left and right (the outside) so that the
set value is made big. Please adjust by liking.
Audyssey Settings
When the room correction and speaker setup is complete, the “Equalizer Settings” (page 69) will be set to “Audyssey”
and the “Dynamic EQ” will be set to “On”.
Dynamic EQ
Off: Audyssey Dynamic EQ off (default).
On: Audyssey Dynamic EQ on.
With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into
account human perception and room acoustics. It does so by selecting the correct frequency response and
surround volume levels moment-by-moment so that the content sounds the way it was created at any volume
level—not just at reference level.
Dynamic Volume (see page 45)
Off:
Light:
Medium:
Heavy:
Audyssey Dynamic Volume™ off.
Light Compression Mode becomes active.
Medium Compression Mode becomes active.
Heavy Compression Mode becomes active. This setting affects volume the most,
causing all sounds to be of equal loudness.
Note:
After the room correction and speaker setup is completed, even if Equalizer Setting is set to other than “Audyssey”, when Dynamic EQ is set to “On”, Equalizer Settings is set to “Audyssey”.
When Dynamic Volume is set to effective, Equalizer Setting is set to “Audyssey” and Dynamic EQ is set to
“On”. When Dynamic EQ is set to “Off”, Dynamic Volume becomes “Off” automatically.
Theater-Dimensional Setting
Listening Angle
Wide: Select if the listening angle is 40 degrees (default).
Narrow: Select if the listening angle is 20 degrees.
With this setting, you can optimize the Theater-DimenFront left speaker
sional listening mode by specifying the angle of the front
left and right speakers relative to the listening position.
Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to
one of the two available settings.
Front right speaker
20°/40°
71
Advanced Setup—Continued
Using the Audio Settings
You can change various audio settings by pressing the [AUDIO] button.
Note:
When the “Audio TV Out” setting is set to “On” (page 78), the [AUDIO] button is disabled.
1
Press the [RECEIVER] button followed by
the [AUDIO] button.
RECEIVER
2
Use the Up and Down [q]/[w] buttons to
select an item.
qwer
3
Use the Left and Right [e]/[r] buttons to
change the setting.
Repeat this step for the other settings.
AUDIO
Tone Control Settings
You can adjust the bass and treble for the front speakers, except when the Direct listening mode is selected.
Bass
–10 dB to +10 dB in 2 dB steps (default: 0 dB)
You can boost or cut low-frequency sounds output by the front speakers.
Treble
–10 dB to +10 dB in 2 dB steps (default: 0 dB)
You can boost or cut high-frequency sounds output by the front speakers.
Notes:
• To bypass the bass and treble tone circuits, select the Direct listening mode.
• This procedure can also be performed on the AV receiver by using its [TONE], [–], and [+] buttons.
Late Night Function
With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear
quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want
to disturb anyone.
Late Night
For Dolby Digital and Dolby Digital Plus sources, the options are:
Off: Late Night function off (default).
Low: Small reduction in dynamic range.
High: Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
Auto: The Late Night function is set to “On” or “Off” automatically (default).
Off: Late Night function off.
On: Late Night function on.
Notes:
• The effect of the Late Night function depends on the material that you are playing and the intention of the original
sound designer, and with some material there will be little or no effect when you select the different options.
• The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby
TrueHD.
• The Late Night function is set to Off when the AV receiver is set to Standby. For Dolby TrueHD sources, it will be
set to Auto.
72
Advanced Setup—Continued
CinemaFILTER
With the CinemaFILTER, you can soften overly bright movie soundtracks, which are typically mixed for reproduction
in a movie theater.
CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Digital Plus,
TrueHD, Dolby Pro Logic IIx Movie, Dolby Pro Logic II Movie, Multichannel, DTS, DTS-ES, DTS Neo:6 Cinema,
DTS 96/24, Neo:6, DTS-HD High Resolution, DTS-HD Master and DTS Express.
Cinema Fltr
Off: CinemaFILTER off (default).
On: CinemaFILTER on.
Note:
The CinemaFILTER may not work when used with certain input sources.
Audyssey Dynamic Volume™
Dyn Vol
See “Dynamic Volume” of “Audio Adjust” on page 71.
Music Optimizer
The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that use
“lossy” compression, such as MP3. The setting is stored individually for each input selector.
M.Optimizer
Off: Music Optimizer off (default).
On: Music Optimizer on.
Note:
The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48kHz
and analog audio input signals. The Music Optimizer is disabled when the Direct listening mode is selected.
Speaker Layout
You can select the priority of the use of SurrBack speakers or FrontHigh speakers.
SpLayout
SurrBk: The sound from surround back speakers is output by priority.
FrontH: The sound from front high speakers is output by priority.
Notes:
• If the “Speaker Type” setting is set to “Bi-Amp” (page 42), or Powered Zone 2 is being used (page 83), this setting
cannot be selected.
• When the listening mode that doesn’t correspond to the switch of the speakers is used, the setting cannot be
selected.
• This setting can also be selected on the remote controller by using [GUIDE/TOP MENU] button.
Speaker Levels
You can adjust the volume of each speaker while listening to an input source.
These temporary adjustments are cancelled when the AV receiver is set to Standby.
Subwfr (Subwoofer) –15 dB to +12 dB (default: 0 dB)
Center
–12 dB to +12 dB (default: 0 dB)
Notes:
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to “No” or “None” in the Speaker Configuration cannot be adjusted (see page 67).
• This setting is not available when the Direct listening mode is used with an analog input signal.
A/V Sync
When using progressive scanning on your DVD/BD player, you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the audio signals.
A/V Sync
0 ms to 100 ms in 10 ms steps
Notes:
• A/V Sync is disabled when the Direct listening mode is used with an analog input source.
• This setting is stored individually for each input selector.
73
Advanced Setup—Continued
Assigning Listening Modes to Input
Sources
4
Use the Up and Down [q]/[w] buttons to
select the signal format that you want to
set, and then use the Left and Right [e]/
[r] buttons to select a listening mode.
Only listening modes that can be used with each
input signal format can be selected (see
pages 60–63).
The Last Valid option means that the listening
mode selected last will be used.
Analog / PCM: With this setting, you can specify
the listening mode to be used when an analog
(CD, TV, LD, VHS, MD, turntable, radio, cassette, cable, satellite, etc.) or PCM digital (CD,
DVD, etc.) audio signal is played.
Dolby D/Dolby D +: With this setting, you can
specify the listening mode to be used when a
Dolby Digital or Dolby Digital Plus format digital
audio signal is played (DVD, etc.).
DTS/DTS HD HR: With this setting, you can
specify the listening mode to be used when a DTS
or DTS-HD High Resolution format digital audio
signal is played (DVD, LD, CD, etc.).
D.F. 2ch: Specifies the default listening mode for
2-channel (2/0) stereo sources in a digital format,
such as Dolby Digital or DTS.
D.F. Mono: With this setting, you can specify the
listening mode to be used when a mono digital
audio signal is played (DVD, etc.).
Multich PCM: Specifies the default listening
mode for multichannel PCM sources input via a
HDMI IN, such as DVD-Audio.
Dolby TrueHD: Specifies the default listening
mode for Dolby TrueHD sources, such as Blu-ray
or HD DVD (input via HDMI).
DTS-HD Master Audio: Specifies the default
listening mode for DTS-HD Master Audio
sources, such as Blu-ray or HD DVD (input via
HDMI).
DSD: Specifies the default listening mode for
DSD multichannel sources, such as SACD.
5
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes during playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
1
Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
2
Use the Up and Down [q]/[w] buttons to
select “5. Listening Mode Preset”, and
then press [ENTER].
The “Listening Mode Preset” menu appears.
5. Listening Mode Preset
1.
2.
3.
4.
5.
6.
7.
8.
9.
3
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
TV/TAPE
TUNER
CD
PORT
Use the Up and Down [q]/[w] buttons to
select the input source that you want to
set, and then press [ENTER].
The signal format selection menu appears.
5–1. Listening Mode Preset
—DVD/BD—
Analog / PCM
Dolby D/Dolby D +
DTS/DTS HD HR
D.F. 2ch
D.F. Mono
Last Valid
Last Valid
Last Valid
Last Valid
Last Valid
For TUNER input selector only “Analog” will be
available.
Notes:
• If you connect an input component (such as UP-A1
series Dock that seated iPod) to the UNIVERSAL
PORT jack, you can assign only “Analog” listening
mode to PORT selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
74
Advanced Setup—Continued
IntelliVolume
Source Setup
This section explains items on the “Source Setup” menu.
Items can be set individually for each input selector.
1
Press the input selector buttons to select
an input source, and then press the
[RECEIVER] button.
2
Press the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
3
Use the Up and Down [q]/[w] buttons to
select “4. Source Setup”, and then press
[ENTER].
The “Source Setup” menu appears. The name of
the currently selected input selector is displayed.
4. Source Setup
—DVD/BD—
1. IntelliVolume
2. A/V Sync
3. Name Edit
4
Use the Up and Down [q]/[w] buttons to
select an item, and then press [ENTER].
With IntelliVolume, you can set the input level for each
input selector individually. This is useful if one of your
source components is louder or quieter than the others.
Use the Left and Right [e]/[r] buttons to set the level.
If a component is noticeably louder than the others, use
the Left [e] button to reduce its input level. If it’s noticeably quieter, use the Right [r] button to increase its
input level. The input level can be adjusted from −12 dB
to +12 dB in 1 dB steps.
Note:
IntelliVolume does not apply for Zone 2.
A/V Sync
When using your DVD player’s progressive scanning
function, you may find that the picture and sound are out
of sync. With the A/V Sync setting, you can correct this
by applying a delay to the audio signal. The delay can be
set from 0 to 100 milliseconds (msec) in 10 millisecond
steps.
Use the Left and Right [e]/[r] buttons to set the delay.
To view the TV picture while setting the delay, press
[ENTER].
To return to the previous screen, press the [RETURN]
button.
4–2. A/V Sync
—DVD/BD—
5
Use the Left and Right [e]/[r] buttons to
change it.
The “Source Setup” menu items are explained
below.
6
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
A/V Sync
0ms
If HDMI Lip Sync is enabled (see page 78), and your TV
or display supports HDMI Lip Sync, the displayed delay
time will be the A/V Sync delay time. The HDMI Lip
Sync delay time is displayed underneath in parentheses.
Note:
A/V Sync is disabled when the Direct listening mode is
used with an analog input source.
75
Advanced Setup—Continued
Name Edit
You can enter a custom name for each individual input
selector and radio preset for easy identification. When
entered, the custom name will appear on the display.
The custom name is edited using the character input
screen.
1. Use the arrow [q]/[w]/[e]/[r] buttons to select a
character, and then press [ENTER].
Repeat this step to enter up to 10 characters.
2. When you’ve finished, to store a name, be sure to
use the arrow [q]/[w]/[e]/[r] buttons to select
“OK”, and then press [ENTER]. Otherwise it will
not be saved.
Name input area
4-3. Name Edit
[
Name
D
Q
d
q
E
R
e
r
F
S
f
s
G
T
g
t
H
U
h
u
I
V
i
v
]
A
N
a
n
B
O
b
o
C
P
c
p
J
W
j
w
K
X
k
x
L
Y
l
y
M
Z
m
z
1
!
{
[
2
@
}
]
3 4 5 6 7 8 9 0 –
`
~
# $ % ^ &
( ) _
| :
< > ? ; ’ , . /
Back
\ SP
OK
(Left)/ (Right):
Selected when the cursor is
moved within the Name input
area.
Back:
“ Back” moves the cursor backward one character space. In
addition, “ Back” deletes the
character to the left of the cursor.
OK:
Selects when the entry is complete.
76
To correct a character:
1. Use the arrow [q]/[w]/[e]/[r] buttons to select
“ ” (Left) or “ ” (Right) and then press
[ENTER].
2. Press [ENTER] several times to select the incorrect
character (The cursor moves one letter each time
[ENTER] is pressed).
3. Use the arrow [q]/[w]/[e]/[r] buttons to select the
correct character, and then press [ENTER].
Notes:
• To name a radio preset, use the [TUNER] button to
select AM or FM, and then select the preset (see step
1 on page 75).
• To restore a custom name to the default, erase the custom name by entering an empty white space for each
letter.
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
Advanced Setup—Continued
Miscellaneous (Volume/OSD) Setup
This section explains the items on the “Miscellaneous”
menu.
1
Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
2
Use the Up and Down [q]/[w] buttons to
select “6. Miscellaneous”, and then press
[ENTER].
The “Miscellaneous” menu appears.
6. Miscellaneous
1. Volume Setup
2. OSD Setup
3
Use the Up and Down [q]/[w] buttons to
select an item, and then press [ENTER].
The screen for that item appears.
4
Use the Up and Down [q]/[w] buttons to
select an item, and use the Left and Right
[e]/[r] buttons to change it.
The items are explained below.
5
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Volume Setup
■ Maximum Volume
With this setting, you can limit the maximum volume.
The Maximum Volume range is “Off”, 79 to 30.
■ Power On Volume
With this preference, you can specify the volume setting
to be used each time the AV receiver is turned on.
The range is “Last”, “Min”, 1 to 79 or “Max”.
To use the same volume level that was used when the AV
receiver was turned off, select “Last”.
The “Power On Volume” cannot be set higher than the
“Maximum Volume” setting.
■ Headphone Level
With this preference, you can specify the headphone volume relative to the main volume. This is useful if there’s
a volume difference between your speakers and your
headphones. The headphones level can be set from –12
dB to +12 dB.
OSD Setup
■ Immediate Display
This preference determines whether operation details are
displayed onscreen when an AV receiver function is
adjusted.
On: Displayed (default).
Off: Not displayed.
Even when “On” is selected, operation details may not
be output if the input source is connected to an HDMI
IN.
■ Display Position
This preference determines where on the screen operation details are displayed.
Bottom: Bottom of the screen (default).
Top: Top of the screen.
■ Language
This setting determines the language used for the
onscreen setup menus. You can select: English, Deutsch,
French, or Spanish.
77
Advanced Setup—Continued
. Hardware Setup
This section explains items on the “Hardware Setup”
menu.
1
2
Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] buttons to
select “7. Hardware Setup”, and then
press [ENTER].
The “Hardware Setup” menu appears.
7. Hardware Setup
1. Remote ID
2. Tuner
3. HDMI
3
Use the Up and Down [q]/[w] buttons to
select an item, and then press [ENTER].
The screen for that item appears.
4
Use the Up and Down [q]/[w] buttons to
select an item, and use the Left and Right
[e]/[r] buttons to change it.
The items are explained below.
5
When you’ve finished, press the
[SETUP] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Remote ID
■ Remote ID
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can
change its remote ID from 1, the default, to 2 or 3.
Note:
If you do change the AV receiver’s remote ID, be sure to
change the remote controller to the same ID (see below),
otherwise, you won’t be able to control it with the remote
controller.
Changing the Remote Controller’s ID
1
78
While holding down the [RECEIVER] button, press and hold down the [SETUP]
button until the Remote indicator lights up
(about 3 seconds).
2
Use the number buttons to enter ID 1, 2, or
3.
The Remote indicator flashes twice.
Tuner
■ FM/AM Frequency Step
See “FM/AM Frequency Step Setup” on page 43.
HDMI
■ Audio TV Out
This preference determines whether audio received at
the HDMI IN is output by the HDMI OUT. You may
want to turn this preference on if your TV is connected
to the HDMI OUT and you want to listen to the audio
from a component that’s connected to an HDMI IN,
through your TV’s speakers. Normally, this should be set
to “Off”.
Off: HDMI audio is not output (default).
On: HDMI audio is output.
Notes:
• If “On” is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
• If “On” is selected, “TV Sp On” appears on the Display by pressing the [DISPLAY] button.
• When “TV Control” is set to “On”, this setting is fixed
to “Auto”.
• With some TVs and input signals, no sound may be
output even when this setting is set to “On”.
• When the “Audio TV Out” setting is set to “On”, or
“TV Control” is set to “On” and you’re listening
through your TV’s speakers (see page 23), if you turn
up the AV receiver’s volume control, the sound will be
output by the AV receiver’s front left and right speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings,
or turn down the AV receiver’s volume.
■ Lip Sync
The AV receiver can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Disable: HDMI lip sync disabled (default).
Enable: HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the A/V Sync screen
(see page 75).
Advanced Setup—Continued
■ x.v.Color
If your HDMI source and HDMI-compatible TV both
support the “x.v.Color”, you can enable “x.v.Color” on
the AV receiver with this setting.
This setting is set to “On” automatically when the above
“HDMI Control (RIHD)” is set to “On” first time.
Disable: “x.v.Color” disabled (default).
Enable: “x.v.Color” enabled.
Notes:
• If the color is unnatural when “x.v.Color” is set to
“Enable”, change the setting to “Disable”.
• Refer to the connected component’s instruction manual for details.
Notes:
• The “Power Control” setting can be set only when the
above “HDMI Control (RIHD)” setting is set to “On”.
• HDMI power control only works with
-compatible components that support it and may not work
properly with some components due to their settings
or compatibility.
• When set to “On”, power consumption will increase.
• When set to “On”, regardless of whether the AV
receiver is On or on Standby, both audio and video
received by an HDMI input will be output by the
HDMI OUT for playback on the TV or other component that’s connected to the HDMI OUT.
• Refer to the connected component’s instruction manual for details.
TV Control
Set to “On” when you want to control the AV receiver
from an
-compatible TV that is connected to
HDMI.
■ HDMI Control (RIHD)
This function allows
-compatible components
connected via HDMI to be controlled with the AV
receiver.
Off:
On:
disabled (default).
enabled.
Notes:
•
, which stands for Remote Interactive over
HDMI, is the name of the system control function
found on Onkyo components. The AV receiver can be
used with CEC (Consumer Electronics Control),
which allows system control over HDMI and is part of
the HDMI standard. CEC provides interoperability
between various components, however, operation with
components other than
-compatible components cannot be guaranteed.
When set to “On” and close the menu, the name of
connected
-compatible components and
“RIHD On” are displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the
component, it is displayed as “Player*” or
“Recorder*”, etc (“*” means the number of two or
more component).
When set to “Off” and close the menu, “RIHD Off”
are displayed on the AV receiver.
“Disconnect” → “RIHD Off”
• When an
-compatible component is connected to the AV receiver via the HDMI cable, the
name of the connected component is displayed on the
AV receiver display. For example, while you are
watching TV broadcasting, if you operate a DVD/BD
player (being powered on) by the remote control of the
AV receiver, the name of the DVD/BD player is displayed on the AV receiver.
• Set to “Off” when a connected piece of equipment is
not compatible or it is unclear whether the equipment
is compatible or not.
• If movement is unnatural when set to “On”, change the
setting to “Off”.
• Refer to the connected component’s instruction manual for details.
Power Control
To link the power functions of
-compatible
components connected via HDMI, select “On”.
Off: Power Control disabled.
On: Power Control enabled.
Off: TV Control disabled.
On: TV Control enabled.
Notes:
• Do not assign the component connected with the
HDMI input to the TV/TAPE selector when you set
“TV Control” setting to “On”. Otherwise, appropriate
CEC (Consumer Electronics Control) operation is not
guaranteed.
• Set to “Off” when the TV is not compatible or when it
is unclear whether the TV is compatible or not.
• The “TV Control” setting can be set only when the
above “HDMI Control (RIHD)” and “Power Control”
settings are both set to “On”.
• Refer to the connected component’s instruction manual for details.
Note:
After changing the settings of the “HDMI Control
(RIHD)”, “Power Control”, or “TV Control”, turn
off the power to all connected pieces of equipment
and then turn them on again. Refer to the User’s
Manuals for all connected pieces of equipment.
79
Advanced Setup—Continued
Lock Setup
Using the Video Settings
With this preference, you can protect your settings by
locking the setup menus.
1
2
You can change various settings of the upconverted
video signal.
Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
RECEIVER
Use the Up and Down [q]/[w] buttons to
select “9. Lock Setup”, and then press
[ENTER].
The “Lock Setup” menu appears.
VIDEO
qwer
9. Lock Setup
Lock
3
4
Unlocked
Use the Left and Right [e]/[r] buttons to
select:
When the setup menus are locked, you cannot
change any setting.
Locked:
Setup menus locked.
Unlocked:
Setup menus not locked.
Press the [SETUP] button.
The setup menu closes.
1
Press the [RECEIVER] button followed by
the [VIDEO] button.
2
Use the Up and Down [q]/[w] buttons to
select an item.
3
Use the Left and Right [e]/[r] buttons to
change the setting.
Repeat this step for the other settings.
■ Resolution (Reso)
You can specify the output resolution for the HDMI outputs and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported
by your TV.
See the “Video Resolution Chart” on page 102 to see
how the AV receiver handles video input at different resolutions.
Through: Select this to pass video through the AV
receiver at the same resolution and with no
conversion (default).
Auto:
Select this to have the AV receiver automatically convert video at resolutions not supported by your TV.
480p:
Select this for 480p output and video conversion as necessary.
720p:
Select this for 720p output and video conversion as necessary.
1080i:
Select this for 1080i output and video conversion as necessary.
Note:
If the resolution is not supported by your TV, it is displayed such as “(1080i)” on the AV receiver.
80
Advanced Setup—Continued
■ Zoom Mode (Zoom)
This setting determines the aspect ratio that will be used
for 480i and 480p input signals when they are output by
the HDMI OUT. This setting only applies when the
HDMI Output Resolution setting is set to 1080i or 720p.
Normal:
■ Saturation
With this setting you can adjust saturation.
Can be adjusted from –20 to +20 in steps of 1 (default
is 0).
“–20” is the weakest color.
“+20” is the strongest color.
■ Sharpness
With this setting you can adjust sharpness.
Can be adjusted from 0 to +5 in steps of 1 (default is 0).
“0” is the default.
“+5” is the sharpest.
Digital Input Signal Formats
Full: (default)
■ Brightness
With this setting you can adjust the picture brightness.
Can be adjusted from –20 to +20 in steps of 1 (default
is 0).
“–20” is the darkest.
“+20” is the brightest.
■ Contrast
With this setting you can adjust Contrast.
Can be adjusted from –20 to +20 in steps of 1 (default
is 0).
“–20” is the least.
“+20” is the greatest.
■ Hue
With this setting you can adjust the red/green balance.
Can be adjusted from –20 to +20 in steps of 1 (default is
0).
“–20” is the strongest green.
“+20” is the strongest red.
The digital input signal formats are available only for the
input sources that you have assigned a digital input jack
(see page 41).
Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
• If noise is produced when fast forwarding or reversing
a DTS CD, try setting the format to DTS.
• The setting is stored individually for each input selector.
1
Press the [RECEIVER] button, and then
press and hold [AUDIO] button for about
8 seconds.
2
While “Auto” is displayed (about 3 seconds), press the Left and Right [e]/[r]
buttons to select: PCM, DTS or Auto.
PCM:
Only 2-channel PCM format input signals will be
heard. If the input signal is not PCM, the PCM
indicator will flash and noise may also be produced.
DTS:
Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS,
the DTS indicator will flash and there will be no
sound.
Auto (default):
The format is detected automatically. If no digital
input signal is present, the corresponding analog
input is used instead.
81
Zone 2
In addition to your main listening room, you can also enjoy playback in the other room, or as we call Zone 2. And, you
can select a different source for each room.
Connecting Your Zone 2 Speakers to an
Amp in Zone 2
Connecting Zone 2
There are two ways you can connect Zone 2 speakers:
1. Connect them directly to the AV receiver.
2. Connect them to an amp in Zone 2.
Connecting Your Zone 2 Speakers Directly
to the AV receiver
This setup allows 5.1-channel playback in your main
room and 2-channel stereo playback in Zone 2, with a
different source in each room. This is called Powered
Zone 2, as the Zone 2 speakers are powered by the AV
receiver. Note that when Powered Zone 2 is turned off,
you can enjoy 7.1-channel playback in your main room.
This setup allows 7.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2,
with a different source in each room.
Hookup
• Use an RCA audio cable to connect the AV receiver’s
ZONE 2 LINE OUT L/R jacks to an analog audio
input on your Zone 2 amp.
• Connect your Zone 2 speakers to the speaker terminals
on your Zone 2 amp.
Main room
TV
To use this setup, you must set the “Powered Zone 2”
setting to “Act” (see page 83).
Hookup
• Connect your Zone 2 speakers to the AV receiver’s
ZONE 2 L/R speaker terminals.
AV receiver
Main room
TV
Zone 2
IN
R
L
AV receiver
Receiver/
integrated amp
Note:
The Zone 2 volume must be set on the Zone 2 amp.
Zone 2
R
L
Notes:
• With this setup, the Zone 2 volume is controlled by the
AV receiver.
• Powered Zone 2 cannot be used if “Speaker Type” is
set to “Bi-Amp” (see page 42).
82
Zone 2—Continued
Setting the Powered Zone 2
4
Use the Up and Down [q]/[w]
buttons to select “Powered
Zone 2”, and use the Left and
Right [e]/[r] buttons to select:
Not Act:
ZONE 2 L/R speaker terminals not
activated (Powered Zone 2 disabled).
Act:
ZONE 2 L/R speaker terminals
activated (Powered Zone 2
enabled).
5
Press the [SETUP] button.
The setup menu closes.
If you’ve connected your Zone 2 speakers to the AV
receiver, as explained in “Connecting Your Zone 2
Speakers Directly to the AV receiver” on page 82, you
must set the “Powered Zone 2” setting to “Act” (Activated).
1
2
Press the [RECEIVER] button
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Use the Up and Down [q]/[w]
buttons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
2. Speaker Setup
1.
2.
3.
4.
5.
3
Speaker Settings
Speaker Configuration
Speaker Distance
Level Calibration
Equalizer Settings
Use the Up and Down [q]/[w]
buttons to select “1. Speaker
Settings”, and then press
[ENTER].
The “Speaker Settings” menu appears.
Notes:
• When “Act” is selected and Zone 2 turned on, the
Zone 2 speakers connected to the ZONE 2 L/R
speaker terminals output sound, but the surround back
or front high speakers connected to the SURR BACK/
FRONT HIGH L/R speaker terminals do not. When
“Act” is selected and Zone 2 turned off, the surround
back or front high speakers output sound as normal.
• When the “Powered Zone 2” setting is set to “Act”
and the input selector of Zone 2 is selected, power
consumption on standby mode slightly increases.
• Powered Zone 2 cannot be used if “Speaker Type” is
set to “Bi-Amp” (see page 42).
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
83
Zone 2—Continued
Controlling Zone 2 with the Remote
Controller
Using Zone 2
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust
the volume for Zone 2.
ON/
STANDBY
Controlling Zone 2 from the AV receiver
ZONE 2
OFF
ZONE2
INPUT
SELECTOR
Note:
To control Zone 2, you must press the remote controller’s [ZONE 2] button first.
INPUT SELECTOR
1
1
Press the [ZONE 2] button, then
point the remote controller at the
AV receiver and press the [ON/
STANDBY] button.
Zone 2 turns on, the ZONE 2 indicator
lights up.
2
To select an input source for
Zone 2, press the [ZONE 2]
button, followed by an INPUT
SELECTOR button.
To select AM or FM press the
[TUNER] INPUT SELECTOR button
repeatedly.
Note:
You cannot select different AM or FM
radio stations for your main room and
Zone 2. The same AM/FM radio station
will be heard in each room.
3
To turn off Zone 2, press the
[ZONE 2] button, followed by the
[ON/STANDBY] button.
To turn on Zone 2 and select an
input source, press the [ZONE 2]
button followed by an input
selector button within 8 seconds.
Zone 2 turns on, the ZONE 2 indicator
lights up.
To select AM or FM press the
[TUNER] input selector button repeatedly.
To select the same source as that of the
main room, press the [ZONE 2] button
repeatedly until “Z2 Selector: Source”
appears on the display.
Note:
You cannot select different AM or FM
radio stations for your main room and
Zone 2. The same AM/FM radio station
will be heard in each room.
2
84
To turn off Zone 2, press the
[OFF] button.
Zone 2—Continued
Adjusting the Volume for Zone 2
Remote
controller
AV receiver
On the remote controller, press
the [ZONE 2] button, and then
use the VOL [q]/[w] button.
On the AV receiver, press the
[ZONE 2] button, and then use
the [–]/[+] buttons.
If your Zone 2 speakers are connected
to a receiver or integrated amp in Zone
2, use its volume control to adjust the
volume.
Notes:
• Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 L/R speaker terminals. Digital input sources are not output. If no sound is heard
when an input source is selected, check if it’s connected to an analog input.
• While Powered Zone 2 is being used, listening modes
that require surround back or front high speakers (6.1/
7.1), such as Dolby Digital EX, DTS-ES and Dolby
Pro Logic IIz Height are unavailable.
• While Zone 2 is on, u functions will not work.
• You cannot select different AM or FM radio stations
for your main room and Zone 2. The same AM/FM
radio station will be heard in each room. For example,
if you have an FM station for the main room, that station will also be used in Zone 2.
• Zones can also be unmuted by adjusting the volume.
• When the “Powered Zone 2” setting is set to “Act”
and the input selector of Zone 2 is selected, power
consumption on standby mode slightly increases.
Muting Zones
Remote
controller
On the remote controller, press
the [ZONE 2] button, and then
press the [MUTING] button.
To unmute a zone, on the remote
controller, press the [ZONE 2]
button, and then press the
[MUTING] button again.
85
Controlling Other Components
You can use the AV receiver’s remote controller
(RC-738M) to control your other AV components,
including those made by other manufacturers. This section explains how to enter the remote control code for a
component that you want to control: DVD, TV, VCR,
etc.
3
8–1. Remote Mode Setup
TV
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
TV/TAPE
CD
Preprogrammed Remote Control
Codes
The following REMOTE MODE buttons are preprogrammed with remote control codes for controlling the
components listed. You do not need to enter a remote
control code to control these components.
For details on controlling these components, see the
pages indicated.
Press [ENTER].
4
Use the Up and Down [q]/[w]
buttons to select remote mode,
and then press [ENTER].
The category selection menu appears.
8–1. Remote Mode Setup
—TV—
Onkyo DVD/BD player (page 91)
TV
TV/DVD
TV/VCR
Onkyo CD player (page 94)
Onkyo cassette recorder with u (page 96)
Onkyo Dock (page 95)
Looking up for Remote Control Code
You can look up for appropriate remote control code
from onscreen setup menu.
Note:
This setting can be carried out by using Onscreen Setup
Menu only.
1
2
Press the [RECEIVER] button
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Use the Up and Down [q]/[w]
buttons to select “8. Remote
Controller Setup”, and then
press [ENTER].
8. Remote Controller Setup
1. Remote Mode Setup
86
5
Use the Up and Down [q]/[w]
buttons to select category, and
then press [ENTER].
The brand name input panel appears.
8–1. Remote Mode Setup
—TV—
Category
Brand
A B C D E F G H I J
N O P Q R S T U V W
1 2 3 4 5 6 7 8 9 0
SP
Back
TV
[xxx]
K L M
X Y Z
– & @
Search
Controlling Other Components—Continued
6
Use the arrow [q]/[w]/[e]/[r]
buttons to select a character, and
then press [ENTER].
Repeat this step from the 1st character
to the 3rd character of the brand name.
When you have entered the 3rd character, select “Search” and press
[ENTER].
After searching, a list of the brand
name appears.
8–1. Remote Mode Setup
—TV—
Category
Brand
8
If you cannot control component,
use the Up and Down [q]/[w]
buttons to select “Doesn’t work
(try next code)” and press
[ENTER].
The next code is appear.
TV
xxx
9
Sharp
:
:
:
Sony
If you can control component,
use the Up and Down [q]/[w]
buttons to select “Works”, and
then press [ENTER].
The “Remote Mode Setup” menu
appears.
When you’ve finished, press the
[SETUP] button.
The setup menu closes.
Not Listed
If the brand name is not found:
Use the Right [r] button to select
“Not Listed”, and then press
[ENTER].
The brand name input panel appears.
7
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Use the Up and Down [q]/[w]
buttons to select brand, and then
press [ENTER].
After searching, a remote control code
and the input procedure appear. Try it.
Code
8–1. Remote Mode Setup
—TV—
xxxxx
1. While holding down Remote Mode
[
TV
], press and hold down [DISPLAY]
(3 seconds).
2. Enter the 5-Digit remote control code.
3. Push [MUTING] to see if the TV responds.
4. Push Remote Mode [RECEIVER].
5. Choose “Works” or “Doesn’t work”.
Works
Doesn’t work (try next code)
87
Controlling Other Components—Continued
Entering Remote Control Codes
You’ll need to enter a code for each component that you
want to control.
Remote
Indicator
DISPLAY
1
Look up the appropriate remote
control code in the separate
Remote Control Codes list.
The codes are organized by category
(e.g., DVD player, TV, etc.).
2
While holding down the REMOTE
MODE button to which you want
to enter a code, press and hold
down the [DISPLAY] button
(about 3 seconds).
Notes:
• Remote control codes cannot be
entered for the [RECEIVER] and
[ZONE 2] buttons.
• Only TV remote control codes can be
entered for the [TV] button.
• Apart from the [RECEIVER], [TV],
and [ZONE 2] buttons, remote control codes from any category can be
entered for the REMOTE MODE
buttons. However, these buttons also
work as input selector buttons
(page 50), so choose a REMOTE
MODE button that corresponds with
the input to which you connect your
component. For example, if you connect your CD player to the CD input,
choose the [CD] button when entering its remote control code.
REMOTE
MODE
(3 seconds)
Number
buttons
3
Within 30 seconds, use the
number buttons to enter the 5digit remote control code.
The Remote indicator flashes twice.
If the remote control code is not entered
successfully, the Remote indicator will
flash once slowly.
Note:
The remote control codes provided are correct at the time
of printing, but are subject to change.
88
Controlling Other Components—Continued
Remote Control Codes for Onkyo
Components Connected via u
Onkyo components that are connected via u are controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
1
Make sure the Onkyo component is
connected with an u cable and an
analog audio cable (RCA).
See page 36 for details.
2
Enter the appropriate remote control code
for the REMOTE MODE button.
• [DVD/BD] button
31612: Onkyo DVD player with u
• [CD] button
71327: Onkyo CD player with u
• [TV/TAPE] button
42157: Onkyo cassette recorder with u
(default)
• [PORT] button
82351: Onkyo Dock (default)
• [TUNER] button
51805: To control the AV receiver’s tuner
(default)
See the previous page for how to enter remote
control codes.
3
Press the REMOTE MODE button, point
the remote controller at the AV receiver,
and operate the component.
Resetting REMOTE MODE Buttons
You can reset a REMOTE MODE button to its default
remote control code.
1
While holding down the REMOTE
MODE button that you want to
reset, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3
seconds).
(3 seconds)
2
Within 30 seconds, press the
REMOTE MODE button again.
The Remote indicator flashes twice,
indicating that the button has been
reset.
Each of the REMOTE MODE buttons
is preprogrammed with a remote control code. When a button is reset, its
preprogrammed code is restored.
Resetting the Remote Controller
You can reset the remote controller to its default settings.
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via u, use
the following remote control codes:
• [DVD/BD] button
30627: Onkyo DVD player without u (default)
• [CD] button
71817: Onkyo CD player without u (default)
• [TV] button
11807:Onkyo TV (default)
If you want to control an Onkyo component by pointing
the remote controller directly at it, use the following
remote control codes:
32900: Onkyo BD player
32901: Onkyo HD-DVD player
70868: Onkyo MD recorder
71323: Onkyo CD recorder
82990: Onkyo Dock
Note:
If you connect an u-capable Onkyo RI Dock to the
TV/TAPE, VCR/DVR or GAME jacks, for u to work
properly, you must set the Input Display accordingly
(see page 44).
1
While holding down the
[RECEIVER] button, press and
hold down the [AUDIO] button
until the Remote indicator lights
up (about 3 seconds).
(3 seconds)
2
Within 30 seconds, press the
[RECEIVER] button again.
The Remote indicator flashes twice,
indicating that the remote controller
has been reset.
89
Controlling Other Components—Continued
Controlling a TV
By pressing the [TV] button that’s been programmed
with the remote control code for TV, you can control
your TV with the following buttons.
For details on entering a remote control code for a different component, see page 88.
The [TV] button is preprogrammed with the remote control code for controlling a TV that supports the
*1. The TV must be able to receive remote control commands via
and be connected to the AV
receiver via HDMI. If controlling your TV via
doesn’t work very well, program your TV’s remote control code into the [TV] button and use the TV remote
mode to control your TV.
Press [TV] button first
a
j
k
a
b
c
d
e
f
l
m
n
o
b TV VOL [q]/[w] button
Adjust the TV’s volume.
c TV [INPUT] button
Selects the TV’s external inputs.
d GUIDE button
Displays the program guide.
e Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to navigate menus and select items.
f SETUP button
Displays a menu.
g [1], [3], [2], [5], [4], [7], [6]
buttons*
Play, Pause, Stop, Rewind, Fast forward, Previous,
and Next.
These buttons works for combination devices.
h SEARCH, REPEAT, RANDOM, and PLAY
MODE buttons*
Function as colored buttons.
i Number buttons
Enter numbers. [0] button enters 11 on some components. [+10] button* works as “--/---” button or
+10.
j DISPLAY button
Displays information.
k MUTING button
Mutes the TV.
l CH +/– button
Select channels on the TV.
g
m PREV CH button
Selects the previous or last channel.
h
n RETURN button
Exits the TV’s setup menu.
i
o AUDIO button*
Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).
p
*1 The
supported by the AV receiver is the CEC
system control function of the HDMI standard.
90
a ON/STANDBY, TV [9] buttons
Set the TV to On or Standby.
p CLR button
Cancels functions and clears entered numbers, or
enters 12.
Notes:
• With some components, certain buttons may not work
as expected, and some may not work at all.
• Buttons marked with an asterisk (*) are not supported
by the
function.
Controlling Other Components—Continued
Controlling a DVD/BD Player, or DVD/BD Recorder
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your DVD
player (HD DVD, Blu-ray, or TV/DVD combination),
you can control your player with the following buttons.
The [DVD/BD] button is preprogrammed with the
remote control code for controlling an Onkyo DVD
player.
For details on entering a remote control code for a different component, see page 88.
The [DVD/BD] button is preprogrammed with the
remote control code for controlling a component that
*1. The component must be able to
supports the
receive remote control commands via
and be
connected to the AV receiver via HDMI. If controlling
your component via
doesn’t work very well,
program your component’s remote control code into the
[DVD/BD] button and use the DVD/BD remote mode to
control your component.
Press the appropriate
REMOTE MODE button first
a
b
c
d
e
f
g
b TV [9] button
Set the TV to On or Standby.
c TV [INPUT] button
Selects the TV’s external inputs.
d TV VOL [q]/[w] button
Adjust the TV’s volume.
e TOP MENU button
Displays a DVD’s top menu or a DVD’s title.
f Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to navigate menus and select items.
g SETUP button
Used to access the DVD/BD player’s settings.
h [1], [3], [2], [5], [4], [7], [6]
buttons
Play, Pause, Stop, Rewind, Fast forward, Previous,
and Next.
i REPEAT button
Used with the repeat playback functions.
l
j SEARCH button*
Used to search title, chapter, and track numbers, and
to search times for locating specific points.
m
n
o
k Number buttons
Used to enter title, chapter, and track numbers, and
to enter times for locating specific points. The [+10]
button* works as a +10 button or “--/---” button.
p
l DISPLAY button
Displays information about the current disc, title,
chapter, or track, including elapsed time, remaining
time, total time, and so on.
q
r
m MUTING button (52)
Mutes or unmutes the AV receiver.
s
t
o VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver.
h
i
j
a ON/STANDBY button
Sets the DVD/BD player to On or Standby.
n DISC +/–, CH +/– button
Selects discs on a DVD changer. Selects TV channels on a component with a built-in tuner.
p MENU button
Displays a DVD’s menu.
k
u
*1 The
supported by the AV receiver is the CEC system
control function of the HDMI standard.
q RETURN button
Exits the DVD/BD player’s setup menu or returns to
the previous menu.
r AUDIO button*
Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).
s RANDOM button*
Used with the random playback function.
91
Controlling Other Components—Continued
t PLAY MODE button*
Selects play modes on components with selectable
play modes.
u CLR button
Cancels functions and clears entered numbers.
Notes:
• With some components, certain buttons may not work
as expected, and some may not work at all.
• If you enter the remote control code for a HD-DVD or
Blu-ray player that has A, B, C, and D or colored buttons, the [SEARCH], [REPEAT], [RANDOM], and
[PLAY MODE] buttons will work as colored or A, B,
C, D buttons. In this case, these buttons cannot be used
to set repeat playback, random playback, or select play
modes.
• Buttons marked with an asterisk (*) are not supported
by the
function.
Controlling a VCR or PVR
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your VCR
(TV/VCR, PVR, DBS/PVR combination or cable/PVR
combination), you can control your video recorder with
the following buttons.
For details on entering a remote control code for a different component, see page 88.
b
c
d
e
f
g
h
b TV [9] button
Set the TV to On or Standby.
c TV [INPUT] button
Selects the TV’s external inputs.
d TV VOL [q]/[w] button
Adjust the TV’s volume.
Press the appropriate
REMOTE MODE button first
a
a ON/STANDBY button
Set the video recorder to On or Standby.
e GUIDE button
Displays the program guide or navigation list.
j
k
l
m
n
f Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to navigate menus and select items.
g SETUP button
Displays the video recorders setup menu.
h Previous [7] button
Previous or instant replay function.
i Number buttons
Enter numbers. The [0] button enters 11 on some
components. The [+10] button works as a +10 button or “--/---” button.
o
j DISPLAY button
Displays information.
p
k MUTING button (52)
Mutes or unmutes the AV receiver.
q
l CH +/– button
Selects TV channels on the video recorder.
m VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver.
n PREV CH button
Selects the previous channel.
i
r
o RETURN button
Exits the menu or returns to the previous menu.
p Next [6] button
Next or advance function.
q Playback button
From left to right: Rewind, Pause, Play, Stop, and
Fast Forward.
r CLR button
Cancels functions or enters the number 12.
Note:
With some components, certain buttons may not work as
expected, and some may not work at all.
92
Controlling Other Components—Continued
Controlling a Satellite Receiver or Cable Receiver
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your satellite receiver, cable receiver, or DVD recorder (DBS/
PVR combination or cable/PVR combination), you can
control your player with the following buttons.
For details on entering a remote control code for a different component, see page 88.
c Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to navigate menus and select items.
e SEARCH, REPEAT, RANDOM, and PLAY
MODE buttons
Function as colored buttons.
g
h
i
j
b
c
d
b GUIDE button
Displays the onscreen program guide.
d SETUP button
Displays the setup menu.
Press the appropriate
REMOTE MODE button first
a
a ON/STANDBY button
Set the component to On or Standby.
f Number buttons
Enter numbers. The [+10] button works as a +10
button or “--/---” button.
g DISPLAY button
Displays information.
h MUTING button (52)
Mutes or unmutes the AV receiver.
i CH +/– button
Selects satellite/cable channels.
k
j VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver.
l
m
k PREV CH button
Selects the previous channel.
n
e
l RETURN button
Exits the menu.
m AUDIO button
Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).
n [1], [3], [2], [5], [4], [7], [6]
buttons
Play, Pause, Stop, Rewind, Fast forward, Previous,
and Next.
f
o
o CLR button
Cancels functions and clears entered numbers.
Note:
With some components, certain buttons may not work as
expected, and some may not work at all.
93
Controlling Other Components—Continued
Controlling a CD Player
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your CD
player, you can control your player with the following
buttons.
The [CD] button is preprogrammed with the remote control code for controlling an Onkyo CD player.
For details on entering a remote control code for a different component, see page 88.
Press the appropriate
REMOTE MODE button first
a ON/STANDBY button
Set the component to On or Standby.
b Arrow [q]/[w]/[e]/[r] and ENTER buttons*
Used to navigate menus and select items.
c SETUP button*
Used to access the Onkyo CD player’s settings.
d [1], [3], [2], [5], [4], [7], [6]
buttons
Play, Pause, Stop, Rewind, Fast forward, Previous,
and Next.
e REPEAT button
Used with the repeat playback function.
a
h
i
j
k
h DISPLAY button
Displays information about the current disc or track,
including elapsed time, remaining time, total time,
and so on.
j DISC +/– button
Selects discs on a CD changer.
k VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver.
d
l
m
g
n
94
g Number buttons
Used to enter track numbers and times for locating
specific points. The [+10] button works as a +10
button or “--/---” button.
i MUTING button (52)
Mutes or unmutes the AV receiver.
b
c
e
f
f SEARCH button*
Used to locate specific points.
l RANDOM button
Used with the random playback function.
m PLAY MODE button*
Selects play modes on components with selectable
play modes.
n CLR button
Cancels functions and clears entered numbers.
Notes:
• Buttons marked with an asterisk (*) are not supported
by the RI control.
• With some components, certain buttons may not work
as expected, and some may not work at all.
Controlling Other Components—Continued
Controlling an RI Dock
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
Dock, you can control your iPod in the Dock with the
following buttons.
For some RI docks, the [ON/STANDBY] button may not
work with a remote control code 82990 (without u).
In this case, make an u connection and enter a remote
control code 82351 (with u).
For details on entering a remote control code, see
page 88.
When Using an RI Dock:
• Connect the RI Dock to the TV/TAPE IN, VCR/DVR
IN, or GAME IN L/R jacks.
• Set the RI Dock’s RI MODE switch to HDD or HDD/
DOCK.
• Set the AV receiver’s Input Display to DOCK (see
page 44).
• See to the Dock’s instruction manual for more information.
Press the appropriate
REMOTE MODE button first
a
a ON/STANDBY button
Turns the iPod on or off.
Notes:
• This button does not turn the Onkyo DS-A2 or DSA2X RI Dock on or off.
• Your iPod may not respond the first time you press this
button, in which case you should press it again. This is
because the remote controller transmits the On and
Standby commands alternately, so if your iPod is
already on, it will remain on when the remote controller transmits an On command. Similarly, if your iPod
is already off, it will remain off when the remote controller transmits an Off command.
b TOP MENU button
Works as a Mode button when used with a DS-A2
RI Dock.
c Arrow [q]/[w] and ENTER buttons
Used to navigate menus and select items.
d Previous [7] button
Restarts the current song. Press it twice to select the
previous song.
e Rewind [5] button
Press and hold to rewind.
h
f Pause [3] button
Pauses playback.
g REPEAT button
Used with the repeat function.
i
j
k
b
l
c
m
n
o
p
q
r
s
d
e
f
g
h DISPLAY button
Turns on the backlight for 30 seconds.
i MUTING button (52)
Mutes or unmutes the AV receiver.
j ALBUM +/– button
Selects the next or previous album.
k VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver.
l MENU button
Exits the menu.
m PLAYLIST [e]/[r] button
Selects the previous or next playlist on the iPod.
n Play [1] button
Starts playback. If the component is off, it will turn
on automatically.
o Next [6] button
Selects the next song.
p Fast Forward [4] button
Press and hold to fast forward.
q Stop [2] button
Stops playback and displays a menu.
95
Controlling Other Components—Continued
r PLAY MODE button
Selects play modes on components with selectable
play modes.
Works as a Resume button when used with a DS-A2
RI Dock.
s RANDOM button
Used with the shuffle function.
Note:
With some components, certain buttons may not work as
expected, and some may not work at all.
Controlling a Cassette Recorder
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your cassette recorder, you can control your cassette recorder
with the following buttons.
The [TV/TAPE] button is preprogrammed with the
remote control code for controlling an Onkyo cassette
recorder when used with an u connection.
For details on entering a remote control code for a different component, see page 88.
Press the appropriate
REMOTE MODE button first
On twin cassette decks, only Deck B can be controlled.
a ON/STANDBY button
Turns the cassette recorder on or off.
b Previous and Next [7]/[6] buttons
The Previous [7] button selects the previous
track. During playback it selects the beginning of
the current track. The Next [6] button selects the
next track.
Depending on how they were recorded, the Previous
and Next [7]/[6] buttons may not work properly with some cassette tapes.
c Rewind and Fast Forward [5]/[4]
buttons
The Rewind [5] button starts rewind. The Fast
Forward [4] button starts fast forward.
a
f
g
d Reverse Play [t] button
Starts reverse playback.
e Play [1] button
Starts playback.
f MUTING button (52)
Mutes or unmutes the AV receiver.
g VOL [q]/[w] button (50)
Adjusts the volume of the AV receiver.
b
c
d
e
*
96
h Stop [2] button
Stops playback.
Note:
An Onkyo cassette recorder connected via u can also
be controlled in Receiver mode.
h
With some components, certain buttons may not work as
expected, and some may not work at all.
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.
If you can’t resolve the issue yourself, try resetting
the AV receiver before contacting your Onkyo
dealer.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VCR/DVR]
button, press the [ON/STANDBY] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
The onscreen setup menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to the MONITOR OUT V, or the COMPONENT
VIDEO OUT, use the AV receiver’s display when
changing settings.
Power
Can’t turn on the AV receiver
• Make sure that the power cord is properly plugged into
the wall outlet.
• Unplug the power cord from the wall outlet, wait five
seconds or more, then plug it in again.
The AV receiver turns off as soon as it’s turned
on
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources,
and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord
and set the volume to maximum. If the AV receiver
stays on, set the volume to minimum, disconnect the
power cord, and reconnect your speakers and input
sources. If the AV receiver turns off when you set the
volume to maximum, disconnect the power cord, and
contact your Onkyo dealer.
Audio
There’s no sound, or it’s very quiet
• Make sure that the digital input source is selected
properly (page 41).
• Make sure that all audio connecting plugs are pushed
in all the way (page 21).
• Make sure that the inputs and outputs of all components are connected properly (pages 23–35).
• Make sure that the polarity of the speaker cables is
correct, and that the bare wires are in contact with the
metal part of each speaker terminal (page 16).
• Make sure that the input source is properly selected
(page 50).
• Make sure that the speaker cables are not shorting.
• Check the volume. The AV receiver is designed for
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
• While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers
(page 52).
• If there’s no sound from a DVD/BD player connected
to an HDMI IN, check the DVD/BD player’s output
settings, and be sure to select a supported audio format.
• Check the digital audio output setting on the connected device. On some game consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer.
• Make sure that none of the connecting cables are bent,
twisted, or damaged.
• Not all listening modes use all speakers (page 64).
• Specify the speaker distances (page 68) and adjust the
individual speaker levels (page 69).
• Make sure that the speaker setup microphone is not
still connected.
• The input signal format is set to PCM or DTS. Set it to
Auto (page 81).
Only the front speakers produce sound
• When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer produce sound.
• Check the Speaker Configuration (page 67).
Only the center speaker produces sound
• If you use the Dolby Pro Logic IIx Movie, Dolby Pro
Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio
station or mono TV program, the sound is concentrated in the center speaker.
• Make sure the speakers are configured correctly
(page 67).
The surround speakers produce no sound
• When the T-D (Theater-Dimensional), Stereo or
Mono listening mode is selected, the surround speakers produce no sound.
• Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
• Make sure the speakers are configured correctly
(page 67).
97
Troubleshooting—Continued
The center speaker produces no sound
• When the Stereo or Mono listening mode is selected,
the center speaker produces no sound.
• Make sure the speakers are configured correctly
(page 67).
The front high and surround back speakers
produce no sound
• Depending on the current listening mode, no sound
may be produced by the front high and surround back
speakers. Select another listening mode (page 64).
• Not much sound may be produced by the front high
and surround back speakers with some sources.
• Make sure the speakers are configured correctly
(page 67).
• While Powered Zone 2 is being used, playback in the
main room is reduced to 5.1-channels and the front
high and surround back speakers produce no sound
(page 82).
The subwoofer produces no sound
• When you play source material that contains no information in the LFE channel, the subwoofer produces
no sound.
• Make sure the speakers are configured correctly
(page 67).
There’s no sound with a certain signal format
• Check the digital audio output setting on the connected device. On some game consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• Depending on the input signal, some listening modes
cannot be selected (pages 60–63).
Can’t get 6.1/7.1 playback
• If no front high and surround back speakers are connected, or the Zone 2 speakers are being used, 6.1/7.1
playback is not possible.
• You can not always select all of the listening modes,
depending on the number of the speakers connected
(pages 60–63).
The volume cannot be set to 79
• Check to see if a maximum volume has been set
(page 77).
• If the volume level of each individual speaker has been
adjusted to high positive values (page 69), then the
maximum master volume possible may be reduced.
Note that the individual speaker volume levels are set
automatically after the Audyssey 2EQ™ Room Correction and Speaker Setup function has been completed (page 46).
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
• An audio cable may be picking up interference. Try
repositioning your cables.
98
The Late Night function doesn’t work
• Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD (page 72).
About DTS signals
• When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to
prevent noise when you use the pause, fast forward, or
fast reverse function on your player. If you switch your
player from DTS to PCM, because the AV receiver
does not switch formats immediately, you may not
hear any sound, in which case you should stop your
player for about three seconds, and then resume playback.
• With some CD and LD players, you won’t be able to
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver
doesn’t recognize it as a genuine DTS signal. In such
cases, you may hear noise.
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a malfunction.
The beginning of audio received by an HDMI IN
can’t be heard
• Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio signals, audio output may not start immediately.
Video
There’s no picture
• Make sure that all video connecting plugs are pushed
in all the way (page 21).
• Make sure that each video component is properly connected (pages 23–35).
• If your TV is connected to the HDMI OUT, select
“- - - - -” in the “HDMI Input Setup” on page 39 to
watch composite video, and component video sources.
• If the video source is connected to a component video
input, you must assign that input to an input selector
(page 40), and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONITOR OUT (pages 26 and 23).
• If the video source is connected to a composite video
input, your TV must be connected to the HDMI OUT
or the corresponding composite video output
(pages 26 and 23).
• If the video source is connected to an HDMI input,
you must assign that input to an input selector
(page 39), and your TV must be connected to the
HDMI OUT (page 23).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
Troubleshooting—Continued
There’s no picture from a source connected to
an HDMI IN
• Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not supported (page 23).
• If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that your TV does not
support the current video resolution and you need to
select another resolution on your DVD/BD player.
The onscreen menus don’t appear
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
The immediate display does not appear
• Depending on the input signal, the immediate display
may not appear when the input signal from the HDMI
IN is output to a device connected to the HDMI OUT.
Tuner
Reception is noisy, FM stereo reception is noisy,
or the FM STEREO indicator doesn’t appear
• Relocate your antenna.
• Move the AV receiver away from your TV or computer.
• Listen to the station in mono (page 53).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
Remote Controller
The remote controller doesn’t work
• Make sure that the batteries are installed with the correct polarity (page 12).
• Install new batteries. Don’t mix different types of batteries, or old and new batteries (page 12).
• Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 12).
• Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
• If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not
work reliably when the doors are closed.
• Make sure you’ve selected the correct remote controller mode (pages 13 and 90-96).
• When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
• Make sure you’ve entered the correct remote control
code (page 88).
• Make sure to set the same ID on both the AV receiver
and remote controller (page 78).
Can’t control other components
• If it’s an Onkyo component, make sure that the u
cable and analog audio cable are connected properly.
Connecting only an u cable won’t work (page 36).
• Make sure you’ve selected the correct remote controller mode (pages 13 and 90–96).
• If you’ve connected an u-capable Onkyo RI Dock to
the TV/TAPE IN, GAME IN or VCR/DVR IN jacks,
for the remote controller to work properly, you must
set the display to DOCK (page 44).
If you cannot operate it, you will need to enter the
appropriate remote control code (page 88).
• To control another manufacturer’s component, point
the remote controller at that component.
• To control an Onkyo component that’s connected via u,
point the remote controller at the AV receiver. Be sure to
enter the appropriate remote control code first (page 89).
• To control an Onkyo component that’s not connected
via u, or another manufacturer’s component, point
the remote controller at the component. Be sure to enter
the appropriate remote control code first (page 88).
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
Dock for iPod
There’s no sound
• Make sure your iPod is actually playing.
• Make sure your iPod is inserted properly in the Dock.
• Make sure the UP-A1 series Dock is connected to the
UNIVERSAL PORT jack on the AV receiver.
• Make sure the AV receiver is turned on, the correct
input source is selected, and the volume is turned up.
• Make sure the plugs are pushed in all the way.
• Try resetting your iPod.
There’s no video
• Make sure that your iPod’s TV OUT setting is set to On.
• Make sure the correct input is selected on your TV or
the AV receiver.
• Some versions of the iPod do not output video.
The AV receiver’s remote controller doesn’t
control your iPod
• Make sure your iPod is properly inserted in the Dock.
If your iPod is in a case, it may not connect properly
to the Dock. Always remove your iPod from the case
before inserting it into the Dock.
• The iPod cannot be operated while it’s displaying the
Apple logo.
• Make sure you’ve selected the right remote mode.
• When you use the AV receiver’s remote controller,
point it toward your amp.
• If you still can’t control your iPod, start playback by
pressing your iPod’s Play button. Remote operation
should then be possible.
• Try resetting your iPod.
• Depending on your iPod, some buttons may not work
as expected.
99
Troubleshooting—Continued
The AV receiver unexpectedly selects your iPod
as the input source
• Always pause iPod playback before selecting a different input source. If playback is not paused, the Direct
Change function may select your iPod as the input
source by mistake during the transition between
tracks.
Recording
Can’t record
• On your recorder, make sure the correct input is
selected.
Zone 2
There’s no sound
• Only components connected to analog inputs can be
played in Zone 2.
Others
The sound changes when I connect my
headphones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, or Direct.
How do I change the language of a multiplex
source
• Use the “Multiplex” setting on the “Audio Adjust”
menu to select “Main” or “Sub” (page 70).
The u functions don’t work
• To use u, you must make an u connection and an
analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 36).
The functions Auto Power On/Standby and
Direct Change don’t work for components
connected via u
• These functions don’t work when Zone 2 is turned on.
When performing “Audyssey 2EQ™ Room
Correction and Speaker Setup”, the
measurement fails showing the message
“Ambient noise is too high”.
• This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these settings.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
2. Use the Left and Right [e]/[r] buttons to change
the setting.
3. Press the input selector button for the input source
that you want to set when you’ve finished.
100
• Video Attenuation
This setting can be made for the DVD/BD, VCR/
DVR, CBL/SAT, GAME, or AUX input.
If you have a games console connected to the composite video input, and the picture isn’t very clear,
you can attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded correctly.
Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby.
Important Note Regarding Video Playback
The AV receiver can upconvert component video and
composite video sources for display on a TV connected
to the HDMI OUT. However, if the picture quality of the
source is poor, upconversion may make the picture
worse or disappear altogether.
In this case, try the following:
1 If the video source is connected to a component
video input, connect your TV to the
COMPONENT VIDEO OUT.
If the video source is connected to a composite video
input, connect your TV to the MONITOR OUT V.
2 On the main menu, select “1. Input Assign”, and
then select “1. HDMI Input”.
Select the relevant input selector, and assign it to
“- - - - -” (page 39).
3 On the main menu, select “1. Input Assign”, and
then select “2. Component Video Input”
(page 40):
If the video source is connected to COMPONENT
VIDEO IN1, select the relevant input selector, and
assign it to “IN1”.
If the video source is connected to COMPONENT
VIDEO IN2, select the relevant input selector, and
assign it to “IN2”.
If the video source is connected to composite video
input, select the relevant input selector, and assign it
to “- - - - -”.
Specifications
Amplifier Section
Rated Output Power
All channels:
80 watts minimum continuous power
per channel, 8 ohm loads, from 20 Hz
to 20 kHz with a maximum total
harmonic distortion of 0.08%.
90 watts minimum continuous power
per channel, 8 ohm loads, at 1 kHz
with a maximum total harmonic
distortion of 0.7%.
130 watts minimum continuous
power per channel, 6 ohm loads, at
1 kHz with a maximum total
harmonic distortion of 1%.
Dynamic Power
180 W (3 Ω, Front)
160 W (4 Ω, Front)
100 W (8 Ω, Front)
THD (Total Harmonic Distortion)
0.08% (Power Rated)
Damping Factor
60 (Front, 1 kHz, 8 Ω)
Input Sensitivity and Impedance
200 mV/47 kΩ (LINE)
Output Level and Impedance
200 mV/2.2 kΩ (REC OUT)
Frequency Response
5 Hz - 100 kHz/+1 dB, - 3 dB (Direct
mode)
Tone Control
±10 dB, 50 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio
106 dB (LINE, IHF-A)
Speaker Impedance
6 Ω - 16 Ω
Video Section
Input Sensitivity/Output Level and Impedance
1 Vp-p/75 Ω
(Component Y)
0.7 Vp-p/75 Ω
(Component PB/CB, PR/CR)
1 Vp-p/75 Ω (Composite)
Component Video Frequency Response
5 Hz - 50 MHz, - 3 dB
Tuner Section
General
Power Supply
AC 120 V, 60 Hz
Power Consumption
5.5 A
Dimensions (W × H × D)
435 × 176 × 329 mm
Weight
(17-1/8" × 6-15/16" × 12-15/16")
10.8 kg (23.8 lbs.)
■ Video Inputs
HDMI
Component
Composite
IN 1, IN 2, IN 3, IN 4, IN 5
IN 1, IN 2
DVD/BD, VCR/DVR, CBL/SAT,
GAME, AUX
■ Video Outputs
HDMI
Component
Composite
OUT
OUT
MONITOR OUT, VCR/DVR
(REC OUT)
■ Audio Inputs
Digital Inputs
Analog Inputs
Optical: 2
Coaxial: 2
DVD/BD, VCR/DVR, CBL/SAT,
GAME, AUX (PORTABLE),
TV/TAPE, CD
■ Audio Outputs
Analog Outputs
TV/TAPE, VCR/DVR,
ZONE 2 LINE OUT
Subwoofer Pre Outputs
Speaker Outputs
Phones
2
Main (L, R, C, SL, SR, SBL, SBR)
+ ZONE2 (L, R)/ Front High (L, R)
1
■ Control Terminal
MIC
Yes
Specifications and features are subject to change without
notice.
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz
AM Tuning Frequency Range
530 kHz - 1710 kHz
Preset Channel
40
101
Video Resolution Chart
The following tables show how video signals at different resolutions are output by the AV receiver.
✔: Output
Output
1080p
Input
1080p
1080i
HDMI
COMPONENT
HDMI
(60Hz/24Hz)
✔
1080i
720p
480p
480p
480i
COMPOSITE
102
480i
480p
480i
480i
✔
✔
480i
COMPONENT
720p
✔
480p
720p
1080i
✔
720p
1080i
480i
COMPOSITE
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Memo
103
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.ch.onkyo.com/
HOMEPAGE
http://www.onkyo.com/
Y0905-1
SN 29400095
(C) Copyright 2009 ONKYO CORPORATION Japan. All rights reserved.
104
* 2 9 4 0 0 0 9 5 *