Product guide | Char-Broil 463460708 Gas Grill User Manual

MODEL 463460708 • PRODUCT GUIDE
THIS GRILL IS FOR OUTDOOR USE ONLY.
CAUTION:
Read and follow all safety statements, assembly
instructions, and use and care directions before
attempting to assemble and cook.
INSTALLER/ASSEMBLER:
Leave this manual with consumer.
CONSUMER:
WARNING:
Failure to follow all manufacturer’s instructions could
result in serious personal injury and/or property
damage.
CAUTION:
Some parts may contain sharp edges – especially as
noted in the manual! Wear protective gloves if
necessary.
Keep this manual for future reference.
If you have questions or need assistance during assembly, please call 1-800-241-7548.
To insure your satisfaction and for follow-up service, register your grill online at www.grillregistration.com
463460708 • 80016598 • 01-03-08
WARNING
DANGER
If you smell gas:
1.
2.
3.
4.
Shut off gas to the appliance.
Extinguish any open flame.
Open lid.
If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
CALIFORNIA PROPOSITION 65
1. Combustion by-products produced when using
this product contain chemicals known to the State of
California to cause cancer, birth defects, and other
reproductive harm.
2. This product contains chemicals, including lead
and lead compounds, known to the State of
California to cause cancer, birth defects or other
reproductive harm.
Wash your hands after handling this product.
Installation Safety Precautions
WARNING
1. Do not store or use gasoline or other
flammable liquids or vapors in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
Call Grill Service Center for Help and Parts
• If you need assistance with your product or warranty parts call
1-800-241-7548. Hours of Service Center Operation are
8:00 A.M. To 6:00 P.M. EST Monday - Friday.
• To order non-warranty replacement parts or accessories
please visit us on the web at www.charbroil.com or call
1-800-241-7548 and one of our friendly and knowledgeable
agents will be glad to assist you.
IMPORTANT: Fill out the product record information below.
Model Number
Serial Number
Safety Symbols
The symbols and boxes shown below explain what each heading
means. Read and follow all of the messages found throughout
the manual.
DANGER
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
See rating label on grill for serial number.
WARNING
WARNING: Indicates an potentially hazardous situation
which, if not avoided, could result in death or serious injury.
Date Purchased
CAUTION
For residential use only. Do not use for commercial
cooking.
2 • 463460708
• Use grill, as purchased, only with LP (propane) gas and the
regulator/valve assembly supplied. A conversion kit must be
purchased for use with natural gas.
• Grill installation must conform with local codes, or in their
absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2, or the Standard for Recreational
Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV Series,
Recreational Vehicle Code, as applicable.
• All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or
National Electrical Code, ANSI / NFPA 70 or Canadian
Electrical Code, CSA C22.1. Keep any electrical cords and/or
fuel supply hoses away from any hot surfaces.
• This grill is safety certified for use in the United States and/or
Canada only. Do not modify for use in any other location.
Modification will result in a safety hazard.
CAUTION
CAUTION: Indicates a potentially hazardous situation or
unsafe practice which, if not avoided, may result in minor
or moderate injury.
TABLE OF CONTENTS
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Grill Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Product Record Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Use and Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
To insure your satisfaction
and for follow-up service,
register your grill
online at:
www.grillregistration.com
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-25
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Stainless Steel Use and Care
Stainless steel grills can provide many years of reliable
service and an attractive appearance in normal outdoor
exposure. Consider the following tips to extend the
appearance of your stainless steel grill:
• Cooking smoke from normal use of the grill will eventually
coat and discolor the stainless steel surface.
• Periodic cleaning of the cooking grates also helps
decrease the risk of a grease fire which can irreversibly
darken the stainless steel surface. (Please note that the
integrity of the steel is not affected by the flame, only the
appearance.)
463460708 • 3
USE AND CARE
DANGER
• NEVER store a spare LP cylinder under or near
the appliance or in an enclosed area.
LP Tank
• The LP tank used with your grill must meet the following
requirements:
• Use LP tanks only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)
capacity maximum.
• LP tanks must be constructed and marked in accordance with
specifications for LP tank of the U.S. Department of
Transportation (DOT) or for Canada, CAN/CSA-B339,
cylinders, spheres and tubes for transportation of dangerous
goods, Transport Canada (TC). See LP tank collar for marking.
• LP tank valve must have:
• Type 1 outlet compatible with
regulator or grill.
• Safety relief valve.
• UL listed Overfill Protection
OPD Hand Wheel
Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. Use
only LP tanks equipped with this type of valve.
• LP tank must be arranged for vapor withdrawal and include
collar to protect LP tank valve.
• Never fill a cylinder beyond 80% full.
• An over filled or improperly stored cylinder is a
hazard due to possible gas release from the
safety relief valve.
• If you see, smell or hear gas escaping,
immediately get away from the LP
cylinder/appliance and call your fire department.
• This could cause an intense fire with risk of
property damage, serious injury or death.
LP Cylinder Removal, Transport and Storage
• Turn OFF all control knobs and LP cylinder valve. Turn coupling
nut counterclockwise by hand only - do not use tools to
disconnect. Loosen cylinder screw beneath bottom shelf, then
lift LP cylinder up and out of cart. Install safety cap onto LP
cylinder valve. Always use cap and strap supplied with valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
• A disconnected LP cylinder in LP Cylinder Valve
storage or being transported
must have a safety cap installed (as shown).
Do not store an LP cylinder in enclosed spaces
such as a carport, garage, porch, covered
Safety
patio or other building. Never leave an LP cylinder
Cap
inside a vehicle which may become overheated
Retainer Strap
by the sun.
• Do not store an LP cylinder in an area where children play.
4 • 463460708
LP cylinder in upright position for vapor withdrawal
LP (Liquefied Petroleum Gas)
• LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten
cabbage) so that it can be smelled.
• LP gas is highly flammable and may ignite unexpectedly when
mixed with air.
LP Cylinder Filling
• Use only licensed and experienced dealers.
• LP dealer must purge new cylinder before filling.
• Dealer should NEVER fill LP cylinder more than 80% of LP
cylinder volume. Volume of propane in cylinder will vary by
temperature.
• A frosty regulator indicates gas overfill. Immediately close LP
cylinder valve and call local LP gas dealer for assistance.
• Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.
• To remove gas from LP cylinder, contact an LP dealer or call a
local fire department for assistance. Check the telephone
directory under “Gas Companies” for nearest certified LP
dealers.
LP Cylinder Exchange
Connecting Regulator to the LP Cylinder
• Many retailers that sell grills offer you the option of replacing
your empty LP cylinder through an exchange service. Use only
those reputable exchange companies that inspect, precision fill,
test and certify their cylinders. Exchange your cylinder only
for an OPD safety feature-equipped cylinder as described
in the "LP Cylinder" section of this manual.
1. LP cylinder must be properly secured onto grill. (Refer to
assembly section.)
• Always keep new and exchanged LP cylinders in upright
position during use, transit or storage.
4. Remove the protective cap from LP cylinder valve. Always use
cap and strap supplied with valve.
2. Turn all control knobs to the OFF position.
3. Turn LP cylinder OFF by turning hand-wheel clockwise to a
full stop.
• Leak test new and exchanged LP cylinders BEFORE
connecting to grill.
Off
Clockwise
LP Cylinder Leak Test
For your safety
OPD Hand Wheel
• Leak test must be repeated each time LP cylinder is exchanged
or refilled.
Type 1 outlet with
thread on outside
• Do not smoke during leak test.
• Do not use an open flame to check for gas leaks.
Safety Relief Valve
• Grill must be leak tested outdoors in a well-ventilated area,
away from ignition sources such as gas fired or electrical
appliances. During leak test, keep grill away from open flames
or sparks.
Strap and Cap
• Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below.
Do not use a POL transport plug
(plastic part with external threads)!
It will defeat the safety feature of
the valve.
s
Do not use household cleaning agents. Damage to gas
train components can result.
5. Hold regulator and insert nipple into LP
cylinder valve. Hand-tighten the
coupling nut, holding regulator in a
straight line with LP cylinder valve so
as not to cross-thread the connection.
Nipple has to be centered
into the LP cylinder valve.
WARNING
If “growing” bubbles appear do not use or move the LP
cylinder. Contact an LP gas supplier or your fire
department!
463460708 • 5
Leak Testing Valves, Hose and Regulator
1. Turn all grill control knobs to OFF.
2. Be sure regulator is tightly connected to LP cylinder.
Str
aig
ht
3. Completely open LP cylinder valve by turning hand wheel
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct
before proceeding.
Hold coupling nut and regulator
as shown for proper connection
to LP cylinder valve.
4. Brush soapy solution onto areas where bubbles are shown in
picture below:
s
Never remove threaded
orifice at end of valve.
6. Turn the coupling nut clockwise and tighten to a full stop. The
regulator will seal on the back-check feature in the LP cylinder
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the
connection. Tighten by hand only – do not use tools.
NOTE:
If you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!
DANGER
• Do not insert any tool or foreign object into the valve
outlet or safety relief valve. You may damage the valve
and cause a leak. Leaking propane may result in
explosion, fire, severe personal injury, or death.
WARNING
• Outdoor gas appliance is not intended to be installed
in or on a boat.
• Outdoor gas appliance is not intended to be installed
in or on an RV.
• Never attempt to attach this grill to the self-contained
LP gas system of a camper trailer or motor home.
• Do not use grill until leak-tested.
• If a leak is detected at any time, STOP and call the fire
department.
• If you cannot stop a gas leak, immediately close
LPcylinder valve and call LP gas supplier or your fire
department!
6 • 463460708
5. If “growing” bubbles appear, there is a leak. Close LP
cylinder valve immediately and retighten connections. If leaks
cannot be stopped do not try to repair. Call for replacement
parts. Order new parts by giving the serial, model number and
name and part number of items needed (see parts list) to the
Grill Service Center at 1-800-241-7548.
6. Always close LP cylinder valve after performing leak test by
turning hand wheel clockwise.
WARNING
For Safe Use of Your Grill and to Avoid Serious
Injury:
• Do not let children operate or play near grill.
• Keep grill area clear and free from materials that burn.
• Do not block holes in sides or back of grill.
• Check burner flames regularly.
• Use grill only in well-ventilated space. NEVER use in
enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of any
kind.
• Do not use charcoal or ceramic briquets in a gas grill.
(Unless briquets are supplied with your grill.)
• Use grill at least 3 ft. from any wall or surface.
Maintain 10 ft. clearance to objects that can catch fire
or sources of ignition such as pilot lights on water
heaters, live electrical appliances, etc.
Safety Tips
s
Before opening LP cylinder valve, check the coupling nut for
tightness.
s
When grill is not in use, turn off all control knobs and LP
cylinder valve.
s
Never move grill while in operation or still hot.
s
Use long-handled barbecue utensils and oven mitts to avoid
burns and splatters.
s
Maximum load for sideburner and side shelf is 10 lbs.
s
The grease tray must be inserted into grill and emptied after
each use. Do not remove grease tray until grill has
completely cooled.
s
Clean grill often, preferably after each cookout. If a bristle
brush is used to clean any of the grill cooking surfaces,
ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.
s
If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.
s
Keep ventilation openings in cylinder enclosure (grill cart) free
and clear of debris.
s
Do not store objects or materials inside the grill cart
enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.
s
The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
s
If you have a grill problem see the "Troubleshooting Section".
s
If the regulator frosts, turn off grill and LP cylinder valve
immediately. This indicates a problem with the cylinder and it
should not be used on any product. Return to supplier!
CAUTION
• Apartment Dwellers:
Check with management to learn the requirements
and fire codes for using an LP gas grill in your
apartment complex. If allowed, use outside on the
ground floor with a three (3) foot clearance from walls
or rails. Do not use on or under balconies.
• NEVER attempt to light burner with lid closed. A
buildup of non-ignited gas inside a closed grill is
hazardous.
• Never operate grill with LP cylinder out of correct
position specified in assembly instructions.
• Always close LP cylinder valve and remove
coupling nut before moving LP cylinder from
specified operation position.
• Putting out grease fires by closing the lid is not possible.
Grills are well ventilated for safety reasons.
• Do not use water on a grease fire. Personal injury may
result. If a grease fire develops, turn knobs and LP
cylinder off.
• Do not leave grill unattended while preheating or burning
off food residue on HI. If grill has not been regularly
cleaned, a grease fire can occur that may damage the
product.
Main Burner Ignitor Lighting
s
Do not lean over grill while lighting.
1. Turn OFF gas burner control valves.
2. Turn ON gas source or tank.
3. Open lid during lighting.
HI.
4. To ignite, ignition burner knob to
5. Push and hold ELECTRONIC IGNITION button.
6. If ignition does NOT occur in 5 seconds, turn the burner
controls OFF, wait 5 minutes and repeat the lighting
procedure.
7. To ignite remaining burners, turn knob to
HI. Starting with
the burners closest to IGNITION BURNERS first.
If ignitor does not work, follow match lighting instructions.
After Lighting: Turn knobs to HI position for warm-up.
463460708 • 7
WARNING
Turn controls and gas source or tank OFF when not
in use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
s
Do not lean over grill while lighting.
1. Open lid. Turn on gas at LP cylinder.
2. Place lit match into match holder (hanging from cart side
panel), light burner on right or left side of grill.
3. Push in and turn far right or far left burner knob to HI. Be sure
burner lights and stays lit.
4. Light adjacent burners in sequence by pushing knobs in and
turning to HI.
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from HIGH to LOW. You should see a smaller flame in
LOW position than seen on HIGH. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
HIGH
LOW
Turning Grill Off
• Turn all knobs to OFF position. Turn LP cylinder off by turning
hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic ignitor
button. "Click" should be heard and spark seen each time
between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified by manufacturer.
General Grill Cleaning
Sideburner Ignitor Lighting
s
Do not lean over grill while lighting.
1. Top cover must be open when burner is operational.
2. To ignite SIDEBURNER, open sideburner cover.
3. Turn sideburner knob to HI, push and hold ELECTRONIC
IGNITOR button.
4. If sideburner does NOT light in 5 seconds, turn knob to OFF,
wait 5 minutes, then repeat lighting procedure.
Sideburner Match Lighting
1. Open sideburner cover.
2. Place lit match near burner.
3. Turn sideburner knob to HI.
Be sure burner lights and
stays lit.
8 • 463460708
• Do not mistake brown or black accumulation of grease and
smoke for paint. Apply a strong solution of detergent and water
or use a grill cleaner with scrub brush on insides of grill lid and
bottom. Rinse and allow to completely air dry. Do not apply a
caustic grill/oven cleaner to painted surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
s
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill’s high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
Cleaning the Burner Assembly
CAUTION
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER TUBE
If you notice that your grill is getting hard to light or that the
flame isn’t as strong as it should be, take the time to check and
clean the venturi’s.
VALVE
CONTROL PANEL
SPIDER WEBS
INSIDE VENTURI
BURNER
In some areas of the country, spiders or small insects have been
known to create “flashback” problems. The spiders spin webs, build
nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of
gas to the burner. The backed-up gas can ignite in the venturi behind
the control panel. This is known as a flashback and it can damage
your grill and even cause injury.
To prevent flashbacks and ensure good performance the burner and
venturi assembly should be removed from the grill and cleaned
before use whenever the grill has been idle for an extended period.
Storing Your Grill
• Clean cooking grates.
• Store in dry location.
• When LP cylinder is connected to grill, store outdoors in a wellventilated space and out of reach of children.
• Cover grill if stored outdoors. Choose from a variety of grill
covers offered by manufacturer.
• Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
• When removing grill from storage, follow “Cleaning the Burner
Assembly” instructions before starting grill.
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1. Turn gas off at control knobs and LP cylinder.
2. Remove cooking grates and flame tamers.
3. Remove screws and carryover tubes from rear of burners.
4. Remove screw and washers to disengage burner from
bracket on firebox.
5. Remove screws to detach electrode from burner. Electrode
should remain in firebox.
6. Carefully lift each burner up and away from valve openings.
We suggest three ways to clean the burner tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well)
into a small hook. Run the hook through each burner
tube several times.
(B) Use a narrow bottle brush with a flexible handle (do not
use a brass wire brush), run the brush through each
burner tube several times.
(C) Wear eye protection: Use an air hose to force air into
the burner tube and out the burner ports. Check each
port to make sure air comes out each hole.
7. Wire brush entire outer surface of burner to remove food
residue and dirt.
8. Clean any blocked ports with a stiff wire such as an open
paper clip.
9. Check burner for damage, due to normal wear and corrosion
some holes may become enlarged. If any large cracks or
holes are found replace burner.
VERY IMPORTANT: Burner tubes must reengage valve
openings. See illustrations at right.
Correct
10. Attach electrode to burner.
burner-to-valve
11. Carefully replace burners.
engagement
12. Attach burners to brackets on firebox.
13. Reposition carryover tubes and attach
to burners. Replace flame tamers and
cooking grates.
x
ebo
Fir
be
r tu
ove
rry
Ca
Firebox
burner
bracket
Electrode
463460708 • 9
Indirect Cooking
Food Safety
Poultry and large cuts of meat cook slowly to perfection on
the grill by indirect heat. The heat from selected burners
circulates gently throughout the grill, cooking meat or poultry
without the touch of a direct flame. This method greatly reduces
flare-ups when cooking extra fatty cuts because there is no direct
flame to ignite the fats and juices that drip during cooking.
Food safety is a very important part of enjoying the outdoor
cooking experience. To keep food safe from harmful bacteria,
follow these four basic steps:
Clean: Wash hands, utensils, and surfaces with hot soapy water
before and after handling raw meat and poultry.
Separate: Separate raw meats and poultry from ready-to-eat
foods to avoid cross contamination. Use a clean platter and
utensils when removing cooked foods.
Cook: Cook meat and poultry thoroughly to kill bacteria. Use a
thermometer to ensure proper internal food temperatures.
Chill: Refrigerate prepared foods and leftovers promptly.
For more information call: USDA Meat and Poultry Hotline at
1-800-535-4555 In Washington, DC (202) 720-3333, 10:00 am4:00 pm EST.
Indirect Cooking Instructions
• Always cook with the lid closed.
• Due to weather conditions, cooking times may vary. During
cold and windy conditions the temperature setting may need
to be increased to insure sufficient cooking temperatures.
ON
OF
OF
OF
F
F
F
1 Burner Cooking
Cook with direct or indirect heat.
Best for smaller meals or foods.
Consumes less fuel.
ON
OF
F
OF
F
ON
2 Burner Cooking
Great indirect cooking on low.
Produces slow, even heating.
Ideal for slow roasting and baking.
Rotisserie Cooking
When using a rotisserie on your grill, you should remove the
cooking grates and warming rack. This will provide
adequate clearance for large foods.
10 • 463460708
How To Tell If Meat Is Grilled Thoroughly
• Meat and poultry cooked on a grill often browns very fast on the
outside. Use a meat thermometer to be sure food has reached
a safe internal temperature, and cut into food to check for
visual signs of doneness.
• Whole poultry should reach 180° F; breasts, 170° F. Juices
should run clear and flesh should not be pink.
• Hamburgers made of any ground meat or poultry should reach
160° F, and be brown in the middle with no pink juices. Beef,
veal and lamb steaks, roasts and chops can be cooked to 145°
F. All cuts of pork should reach 160° F.
• NEVER partially grill meat or poultry and finish cooking later.
Cook food completely to destroy harmful bacteria.
• When reheating takeout foods or fully cooked meats like hot
dogs, grill to 165° F, or until steaming hot.
CARE AND CLEANING OF YOUR STAINLESS STEEL GRILL
Routine cleaning is necessary to preserve the appearance and corrosion resistance of Stainless Steel. The perception that
many people have is that stainless steel will not rust. That is not the case in certain conditions. Rust marks are regular steel
particles that have become attached to the surface of stainless steel. They may also occur if you are using a steel wool or
wire wool scouring pad instead of a nylon scouring pad to clean your grill. In coastal areas, small rust pits may develop on
the surface of your grill that cannot be fully removed by a cleaner. Concentrate bleaches and other solutions containing
chlorine can also cause rust pits and should not be used.
Cooking creates smoke that may eventually coat and discolor the stainless steel surface. Grease fires will darken the
stainless steel surface, but will not affect the integrity of the steel. Periodic cleaning of the cooking surface and inside of the
grill helps decrease the risk of a fire. The methods below are suggestions for cleaning stainless steel surfaces. Choose a
cleaning method appropriate for your needs. It is recommended that you use a Char-Broil® grill cover to help prolong the
life and prevent discoloration of your grill.
Routine Care
After each use, let your grill cool and then wipe the grill with a soft, damp, soapy cloth and rinse with clean water. It is
important to remove any food particles or marinade from the stainless steel surface of your grill. Most marinades are highly
acidic and damage stainless steel. DO NOT USE STEEL OR WIRE WOOL. To clean, polish and protect your stainless steel
grill on a weekly basis use Char-Broil® Stainless Steel Grill Cleaner. For quick, convenient cleaning, use Char-Broil®
Stainless Steel Grill Wipes.
Stubborn Stains and Rust
Stubborn stains, discoloration and possibly rust and rust pitting can occur from cooking, exposure to harsh outdoor
conditions, or extreme cooking temperatures. For stubborn rust stains and grease stains, you can restore your grill with the
Char-Broil Stainless Steel Restoration Kit. It is available at major retailers retailers or you can buy it online at
www.charbroil.com or www.grilllovers.com. For the latest new products and information for the care and cleaning of your
stainless steel grill go to www.charbroil.com.
* Always rub or wipe in the direction of the grain or polish lines in the stainless steel surface, not across them.
** Do not let stainless steel cleaners come in contact with painted or plastic surfaces as damage may occur.
ROUTINE CARE
Char-Broil® Stainless Steel
Grill Cleaner
ROUTINE CARE
Char-Broil® Stainless Steel
Grill Wipes
STUBBORN STAINS AND RUST
Char-Broil® Stainless Restoration Kit
463460708 • 11
PARTS LIST – Model No. 463460708
Key Qty
A
1
B
4
C
1
D
3
E
1
F
1
G
1
H
1
I
1
J
1
K
1
L
1
M
1
N
5
O
5
P
1
Q
4
R
1
S
1
T
1
U
1
V
1
W
1
X
1
Y
1
Z
1
AA
1
BB
1
CC
1
DD
2
EE
2
FF
1
Description
Part #
Firebox . . . . . . . . . . . . . . . . . . . . . . . . . 80009946
Tube Burner . . . . . . . . . . . . . . . . . . . . . 80009947
Electrode, Main Burner. . . . . . . . . . . . . 80009948
Carryover Tubes. . . . . . . . . . . . . . . . . . 80009949
Lid Assembly . . . . . . . . . . . . . . . . . . . . 80009950
Lid Insert. . . . . . . . . . . . . . . . . . . . . . . . 80009951
Logo Plate . . . . . . . . . . . . . . . . . . . . . . 80005765
Temperature Gauge w/Bezel . . . . . . . . 80009952
Handle . . . . . . . . . . . . . . . . . . . . . . . . . 80009953
Control Panel . . . . . . . . . . . . . . . . . . . . 80016500
Electronic Ignition Module . . . . . . . . . . 80009955
Electronic Ignition Button . . . . . . . . . . . 80004341
Valve/Hose/Regulator. . . . . . . . . . . . . . 80015817
Bezels. . . . . . . . . . . . . . . . . . . . . . . . . . 80003107
Control Knobs. . . . . . . . . . . . . . . . . . . . 80008675
Match Holder . . . . . . . . . . . . . . . . . . . . 80004320
Flame Tamers. . . . . . . . . . . . . . . . . . . . 80008074
Cooking Grate (Set of 3) . . . . . . . . . . . 80008076
Swing Away . . . . . . . . . . . . . . . . . . . . . 80016601
Left Shelf . . . . . . . . . . . . . . . . . . . . . . . 80016599
Sideburner Drip Pan. . . . . . . . . . . . . . . 80016509
Sideburner, W/ Electrode . . . . . . . . . . . 80016504
Left Fascia . . . . . . . . . . . . . . . . . . . . . . 80016501
Right Side Shelf . . . . . . . . . . . . . . . . . . 80016520
Right Fascia . . . . . . . . . . . . . . . . . . . . . 80016502
Front Brace. . . . . . . . . . . . . . . . . . . . . . 80016579
Right Side Panel, Cart . . . . . . . . . . . . . 80016572
Left Side Panel, Cart . . . . . . . . . . . . . . 80016573
Bottom Shelf. . . . . . . . . . . . . . . . . . . . . 80016574
Non-Locking Casters . . . . . . . . . . . . . . 80004093
Locking Casters . . . . . . . . . . . . . . . . . . 80000268
Grease Cup Clip. . . . . . . . . . . . . . . . . . 80000271
Key Qty
GG 1
HH
1
II
1
JJ
1
KK
1
LL
1
MM 1
NN
2
OO 1
4
1
1
Description
Part #
Grease Cup . . . . . . . . . . . . . . . . . . . . . 80000270
Left Door. . . . . . . . . . . . . . . . . . . . . . . . 80016592
Right Door . . . . . . . . . . . . . . . . . . . . . . 80016593
Tank Exclusion Shelf . . . . . . . . . . . . . . 80009971
Tank Exclusion Wire. . . . . . . . . . . . . . . 80009972
Sideburner Grate . . . . . . . . . . . . . . . . . 80003591
Sideburner Lid . . . . . . . . . . . . . . . . . . . 80016600
Door Handle . . . . . . . . . . . . . . . . . . . . . 80009975
Tank Retainer Screw . . . . . . . . . . . . . . 80006484
Door Magnet Assembly . . . . . . . . . . . . 80010057
Product Guide (English) . . . . . . . . . . . . 80016598
Hardware Pack. . . . . . . . . . . . . . . . . . . 80016503
1 Wrench . . . . . . . . . . . . . . . . . . . . . 80000283
2 Lid Support, Side burner . . . . . . . . 80000054
2 Insulation Washers
22 #1/4-20x1/2" Machine Screws
10 Lock Washers, 7mm
10 Flat Washers, 7mm
12 Fiber Washers, 7mm
12 #1/4-20 Flange Nuts
14 #8-32x3/8" Machine Screws
14 Flat Washers, 5mm
14 Lock Washers, 5mm
2 #8-32 Flange Nuts
14 #10-24x1/2" Machine Screw
2 #10-24 Flange Nut
Certified Grill Parts And Accessories®, Char-Broil and Design®, Char-Broil (Gas Grill Briquettes)®, Char-Diamonds®, Cooking Zone and Design®, Diamond Flame®, Executive Chef®, Faststart®, Flare Fighter®, FlavorMaster®, Gas Grill
Silouette and Design®, H2O Smoker®, Lava Flame®, MasterFlame®, MasterFlame Precision Cooking System®, PowerSpark®, Quantum®, VIP®, PrecisionFlame and Design®, Sierra®, and TruFlame® are registered Trademarks of the W.C.
Bradley Company. Thermos® is a registered trademark of the Thermos Company and its affiliates.
Artisan Collection by Char-Broil ™, C3 and Design™, Char-Broil and Design™, Flame Design™, FlavorTents™, Grill 2 Go™, Grillin’ Stick™, Keeper of the Flame™, Keepers of the Flame™, Natural Grip™, Outdoor Cooking Collection and
Design™, Patio Bistro™, PrecisionFlame™, Pro-Check™, QuickSet Grills and Design™, SmokerTents™, The Big Easy™, The Minute Grill™, The Edge™, The Tuscan Collection™, and The Urban Grill™ are Trademarks of the W.C. Bradley
Company. Universal Grill Parts and Design™ is a trademark of the Thermos Company and its affiliates.
Protected under one or more of the following U.S. Patents: 4,598,692; 4,624,240; 4,747,391; 4,747,391; 4,817,583; 4,924,846; 4,989,579; 5,003,960; 5,076,256; 5,076,257; 5,090,398; 5,109,834; 5,224,676; 5,277,106; 5,421,319; 5,441,226;
5,452,707; 5,458,309; 5,566,606; 5,566,606; 5,579,755; 5,582,094; 5,613,486; 5,649,475; 5,706,797; 5,711,663; 5,765,543; 5,931,149; 5,996,573; 6,095,132; 6,135,104; 6,173,644B1; 6,279,566; 6,397,731; 6,418,923; 6,439,222; 6,523,461;
D282,619; D339,714; D341,292; D343,337; D358,059; D361,466; D364,535; D372,637; D373,701; D377,735; D383,035; D397,910; D405,643; D405,643; D406,005; D406,009; D413,043; D413,229; D413,229; D414,982; D415,388; D416,164;
D416,441; D416,441; D417,587; D422,516; D423,274; D423,876; D428,303; D435,396; D436,004; D438,059; D438,060; D438,427; D439,110; D442,505; D443,179; D443,354; D447,384; D447,385; D447,909; D448,610; D448,614; D448,615;
D448,616; D448,975; D449,492; D451,759; D456,202S; D460,313, D461,359 and D504,048. Canada: 87743; 87744; 92607; 92608 and 1,316,424. Other Patents Pending. Assembly instructions © 2006.
12 • 463460708
PARTS DIAGRAM – Model No. 463460708
S
G
H
E
R
MM
F
Q
LL
D
B
A
U
I
V
M
K
X
T
N C
L
W
Y
J
FF
O
N
O
AA
GG
BB
NN
Z
P
KK
JJ
II
HH
CC
EE
DD
OO
463460708 • 13
ASSEMBLY – Model No. 463460708
1
Attach the two locking casters at the rear of the bottom shelf and the two non-locking casters at the front. Use the
provided caster wrench to fully tighten casters.
Non-locking caster
Locking caster
Front
Bottom shelf
Rear
2
Attach side panels to bottom shelf using three 1/4-20x1/2”
screws, 7mm lock washers, and 7mm flat washers per panel.
IMPORTANT: Panel with large hole must
Be on left side of bottom shelf.
1/4-20x1/2” screw
7mm lock washer
7mm flat washer
Right side panel
Make sure side panels
are pushed as far to the
rear of bottom shelf as
possible before fully
tightening screws.
Left side panel
(with large hole)
Re
ar
14 • 463460708
3
Attach front brace to side panels using two #10-24X1/2” screws, 5mm lock washers and 5mm flat washers on each side.
Magnet
5mm flat washers
#10-24x1/2”
screws
5mm lock washers
Rear
4
Insert wire ends on tank exclusion shelf into bottom shelf (A). Attach with two #8-32x3/8" screws diagonally. Tighten two #832x3/8" screws at the back of tank exclusion wire first (B). Line up the front of tank exclusion wire to holes in top brace and
secure with two #8-32x3/8" screws and #8-32 flange nuts.
#8-32 Flange Nut
#8-32x3/8" Screw
B
#8-32x3/8" Screw
A
463460708 • 15
5
Two #8-32x3/8" machine screws are installed partially in the cart side panel. Slide door hinges onto the screws as shown.
Secure right door with four #8-32x3/8" machine screws. Repeat assembly for left door.
#8-32x3/8" machine screw
6
This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart,
aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the
cart. Insert four 1/4-20x1/2” screws through side panels and firebox in all four corners. Secure with four fiber washers and
1/4-20 flange nuts.
1/4-20 flange nut
fiber washer
s
Post
Posts
1/4-20x1/2" screw
16 • 463460708
7
Mount fascia onto side shelf using three #10-24x1/2" screws, 5mm lock washers and 5mm flat washers (A).
Hang side shelf on tabs mounted on the firebox. Secure shelf brackets to cart side panel using two 1/4-20x1/2" screws,
fiber washers and 1/4-20 flange nuts on each bracket (B).
Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and 7mm flat washers (C).
CAUTION
Repeat on
front bracket
SHARP EDGES! Wear gloves if necessary.
fibe
r wa
Flange
Nut
sher
B
B
1/4-20x1/2”
screw
Side shelf
C
A
A
C
1/4-20x1/2"
Screw
Flat Washer
Repeat on
left side shelf
Lock Washer
8
Repeat step 7 (A) on left side shelf. Hang sideburner shelf on tabs mounted on
the firebox. Secure shelf brackets to cart side panel using two 1/4-20x1/2"
screws, fiber washers and 1/4-20 flange nuts on each bracket (A).
Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and
7mm flat washers (B).
A
A
fiber
rew
” sc
er
wash
2
0x1/
1/4-2
flange
nut
CAUTION
SHARP EDGES! Wear gloves if necessary.
7mm flat
washer
7mm lock
washer
1/4-20x1/2”
screw
B
463460708 • 17
9
Place drip pan onto sideburner shelf. Secure with #10-24x 1/2" screws, insulation washers, 5mm flat washers, 5mm
lock washers , #10-24 hex nuts, #10-24x 1/2” screws, 5mm lock washers, 5mm flat washers and side burner lid
supports.
#10-24 x ½" Screws
Insulation Washers
s
d
li
er
urn
5mm Flat Washers
rt
po
p
su
b
e
Sid
5mm Lock Washers
#10-24 Hex Nut
5mm Flat Washers
5mm Lock Washers
#10-24 x ½" Screws
10
Remove two #8-32x3/8" screws from sideburner valve bracket. From behind the fascia, place sideburner valve bracket into
hole. Attach bezel to valve with #8-32x3/8" screws. Press sideburner control knob onto valve stem.
Sideburner
valve bracket
Control knob bezel
Control knob
18 • 463460708
11
Insert sideburner into sideburner drip pan (A), make sure burner tube engages with sideburner valve. Illustration (B) shows
correct burner-to-valve engagement. Center stud on bottom of sideburner fits into center hole in sideburner drip pan. Secure
with one wingnut (C). Connect sideburner ignitor wire to sideburner electrode.
Burn
er tu
be
B
Valv
e
Sideburner
C
Electrode
Sideburner
ignitor wire
A
12
Place sideburner cooking grate into holes in drip pan.
Sideburner
grate
463460708 • 19
rebo
of fi
Fro
x
tam
er
Fl
Fla
me
nt o
am
er
k
Bac
Place four flame tamers over burners by inserting tabs into slots in front of firebox. Opposite ends of flame tamers rest on
pins in back of firebox.
am
et
13
14
Place cooking grates into grill bottom.
Cooking Grates
20 • 463460708
f fir
ebo
x
15
To assemble Swing Away, first insert pivot wire into holes in side of grill lid. Second, insert leg wires into holes in sides
of grill bottom.
Pivot wire
Swing Away
Leg wire
16
Hang grease cup wire from bottom of firebox and place grease cup into grease cup clip.
CAUTION
Failure to install grease cup will cause
hot grease to drip from bottom of grill
with risk of fire or property damage.
Grease Cup Wire
Grease Cup
463460708 • 21
17
Unscrew ignitor cap and place AA battery into ignitor slot with positive end (+) facing outward. Screw ignitor cap onto ignitor.
AA Battery
–
18
+
LP tank is sold separately. Fill and leak check the tank (see Use & Care section) before attaching to grill and regulator.
Once tank has been filled and leak checked, place tank into tank hole in bottom shelf as shown. Secure tank with tank
screw at rear of bottom shelf.
See Use & Care section to perform the “Burner Flame Check” and for important safety instructions
before using.
CAUTION
Failure to install tank correctly may allow gas hose to be
damaged in operation, resulting in the risk of fire.
Tank screw
LP Cylinder
(not included)
22 • 463460708
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.
Emergencies
Possible Cause
Prevention/Solution
Gas leaking from
cracked/cut/burned
hose.
• Damaged hose.
• Turn off gas at LP cylinder or at source on natural gas systems. If
anything but burned, replace valve/hose/regulator. If burned,
discontinue use of product until a plumber has investigated cause
and corrections are made.
Gas leaking from LP
cylinder.
• Mechanical failure due to rusting or
mishandling.
• Replace LP cylinder.
Gas leaking from LP
cylinder valve.
• Failure of cylinder valve from
mishandling or mechanical failure.
• Turn off LP cylinder valve. Return LP cylinder to gas supplier.
Gas leaking between
LP cylinder and
regulator connection.
• Improper installation, connection not
tight, failure of rubber seal.
• Turn off LP cylinder valve. Remove regulator from cylinder and
visually inspect rubber seal for damage. See LP Cylinder Leak Test
and Connecting Regulator to the LP Cylinder.
Fire coming through
control panel.
• Fire in burner tube section of burner due
to blockage.
• Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After fire is out and grill is cold, remove
burner and inspect for spider nests or rust. See Natural Hazard
and Cleaning the Burner Assembly pages.
Grease fire or
continuous excessive
flames above cooking
surface.
• Too much grease buildup in burner area.
• Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After cooling, clean food particles and
excess grease from inside firebox area, grease tray, and other
surfaces.
Possible Cause
Prevention/Solution
GAS ISSUES:
• Trying to light wrong burner.
• See instructions on control panel and in Use and Care section.
• Burner not engaged with control valve.
• Make sure valves are positioned inside of burner tubes.
• Obstruction in burner.
• Ensure burner tubes are not obstructed with spider webs or other
matter. See cleaning section of Use and Care.
• No gas flow.
• Make sure LP cylinder is not empty. If LP cylinder is not empty,
refer to “Sudden drop in gas flow.”
• Vapor lock at coupling nut to LP cylinder.
• Turn off knobs and disconnect coupling nut from LP cylinder.
Reconnect and retry.
• Coupling nut and LP cylinder valve not
fully connected.
• Turn the coupling nut approximately one-half to three-quarters
additional turn until solid stop. Tighten by hand only - do not use
tools.
Troubleshooting
Problem
Burner(s) will not light
using ignitor.
(See Electronic Ignition
Troubleshooting also)
Continued on next
page.
ELECTRICAL ISSUES:
• Electrode cracked or broken; “sparks at
crack.”
• Replace electrode(s).
• Electrode tip not in proper position.
Main Burners:
• Tip of electrode should be pointing toward gas port opening on
burner. The distance should be 1/8” to 1/4”. Adjust if necessary.
Sideburner:
• Tip of electrode should be pointing toward gas port opening on
burner. the distance should be 1/8” to 3/16”. Adjust if necessary.
• Wire and/or electrode covered with
cooking residue.
• Clean wire and/or electrode with rubbing alcohol and clean swab.
• Wires are loose or disconnected.
• Reconnect wires or replace electrode/wire assembly.
• Wires are shorting (sparking) between
ignitor and electrode.
• Replace ignitor wire/electrode assembly.
• Dead battery.
• Replace with a new AA-size alkaline battery.
463460708 • 23
Troubleshooting (continued)
Problem
Possible Cause
Prevention/Solution
Burner(s) will not light
using ignitor.
(See Electronic Ignition
Troubleshooting also)
ELECTRONIC IGNITION:
• No spark, no ignition noise.
• See Section I of Electronic Ignition System.
• No spark, some ignition noise.
• See Section II of Electronic Ignition System.
• Sparks, but not at electrode or at full
strength.
• See Section III of Electronic Ignition System.
Burner(s) will not
match light.
PIEZO PUSH-BUTTON AND ROTARY:
• Push-button sticks at bottom.
• Replace ignitor.
• Rotary knob rotates without clicking.
• Replace knob.
• Sparking between ignitor and electrode.
• Inspect wire insulation and proper connection. Replace wires if
insulation is broken.
• See “GAS ISSUES:” on previous page.
• Match will not reach.
• Use long-stem match (fireplace match).
• Improper method of match-lighting.
• See “Match-Lighting” section of Use and Care.
• Out of gas.
• Check for gas in LP cylinder.
• Excess flow valve tripped.
• Turn off knobs, wait 30 seconds and light grill. If flames are still low,
turn off knobs and LP cylinder valve. Disconnect regulator.
Reconnect regulator and leak-test. Turn on LP cylinder valve, wait
30 seconds and then light grill.
• Vapor lock at coupling nut/LP cylinder
connection.
• Turn off knobs and LP cylinder valve. Disconnect coupling nut from
cylinder. Reconnect and retry.
• High or gusting winds.
• Turn front of grill to face wind or increase flame height.
• Low on LP gas.
• Refill LP cylinder.
• Excess flow valve tripped.
• Refer to “Sudden drop in gas flow” above.
• Grease buildup.
• Clean burners and inside of grill/firebox.
• Excessive fat in meat.
• Trim fat from meat before grilling.
• Excessive cooking temperature.
• Adjust (lower) temperature accordingly.
Persistent grease fire.
• Grease trapped by food buildup around
burner system.
• Turn knobs to OFF. Turn gas off at LP cylinder. Leave lid in position
and let fire burn out. After grill cools, remove and clean all parts.
Flashback...
(fire in burner tube(s)).
• Burner and/or burner tubes are blocked.
• Turn knobs to OFF. Clean burner and/or burner tubes. See burner
cleaning section of Use and Care.
Unable to fill LP
cylinder.
• Some dealers have older fill nozzles
with worn threads.
• The worn nozzles don’t have enough “bite” to engage the valve. Try
a second LP dealer.
One burner does not
light from other
burner(s).
• Grease buildup or food particles in
end(s) of carryover tube(s).
• Clean carry-over tube(s) with wire brush.
Sudden drop in gas
flow or low flame.
Flames blow out.
Flare-up.
24 • 463460708
Troubleshooting - Electronic Ignition
Problem (Ignition)
SECTION I
No sparks appear at
any electrodes when
ignition button is
pushed; no noise can
be heard from spark
module.
SECTION II
No sparks appear at
any electrodes when
ignition switch is
pushed; noise can be
heard from spark
module.
SECTION III
Sparks are present
but not at all
electrodes and/or not
at full strength
Possible Cause
Check Procedure
Prevention/Solution
• Battery not installed
properly.
• Check battery orientation.
• Install battery (make sure that “+” and “–”
connectors are oriented correctly, with “+” end up
and “–” end down.)
• Dead battery.
• Has battery been used
previously?
• Replace battery with new AA-size alkaline battery.
• Button assembly not
installed properly.
• Check to insure threads are
properly engaged. Button
should travel up and down
without binding.
• Unscrew button cap assembly and reinstall, making
sure threads are aligned and engaged fully.
• Faulty spark module.
• If no sparks are generated
with new battery and good
wire connections, module is
faulty.
• Replace spark module assembly.
• Output lead
connections not
connected.
• Are output connections on
and tight?
• Remove and reconnect all output connections at
module and electrodes.
• Output lead
connections not
connected.
• Are output connections on
and tight?
• Remove and reconnect all output connections at
module and electrodes.
• Arcing to grill away
from burner(s).
• If possible, observe grill in
dark location. Operate
ignition system and look for
arcing between output wires
and grill frame.
• If sparks are observed other than from burner(s),
wire insulation may be damaged. Replace wires.
• Weak battery.
• All sparks present but weak
or at slow rate.
• Replace battery with a new AA-size alkaline battery.
• Electrodes are wet.
• Has moisture accumulated
on electrode and/or in burner
ports?
• Use paper towel to remove moisture.
• Electrodes cracked or
broken “sparks at
crack”.
• Inspect electrodes for
cracks.
• Replace cracked or broken electrodes.
463460708 • 25
LIMITED WARRANTY
Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after
correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase.
The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid, by the consumer, for review and
examination.
One year LIMITED warranty
Upon consumer supplying proof of purchase as provided herein, Manufacturer will repair or replace the parts listed below which are proven
defective during the applicable warranty period. Parts required to complete such repair or replacement shall be free of charge to you except for
shipping costs. The original consumer-purchaser will be responsible for all shipping charges of parts replaced under the terms of this
limited warranty.
This limited warranty is applicable in the United States and Canada only, is only available to the original owner of the product and is not
transferable. Manufacturer requires reasonable proof of your date of purchase. Therefore, you should retain your sales slip or invoice and register
your new product immediately. Defective or missing parts subject to this limited warranty will not be replaced without registration and proof of
purchase. Register online at http://www.charbroil.com or complete and return via mail the Product Registration Card located on the last page of the
Use & Care manual included with this product and retain your sales receipt for proof of purchase.
This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents, corrosions
or discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or the
discoloration of stainless steel surfaces. The warranty for your grill covers manufacturing defects. Surface rust, corrosion, or powder paint chipping
on metal parts that does not affect the structural integrity of the product is not considered a defect in workmanship or material and is not covered by
this warranty.
This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage.
If an original replacement part is not available, a comparable replacement part will be sent. You will be responsible for all shipping charges of
parts replaced under the terms of this limited warranty.
ITEMS MANUFACTURER WILL NOT PAY FOR:
1. Service calls to your home.
2. Repairs when your product is used for other than normal, single-family household or residential use.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with
electrical or plumbing codes, or use of products not approved by the manufacturer.
4. Any food loss due to product failures.
5. Replacement parts or repair labor costs for units operated outside the United States or Canada.
6. Pickup and delivery of your product.
7. Repairs to parts or systems resulting from unauthorized modifications made to the product.
8. The removal and/or reinstallation of your product.
9. Shipping cost, standard or expedited, for warranty and replacement parts.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
Repair or replacement of defect parts is your exclusive remedy under the terms of this limited warranty. Manufacturer will not be responsible for
any consequential or incidental damages arising from the breach of either this limited warranty or any applicable warranty, or for failure or damage
resulting from acts of God, improper care and maintenance, grease fire, accident, alteration,
replacement of parts by anyone other than Manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather,
acts of nature, animal tampering), improper installation or installation not in accordance with local codes or printed manufacturer instructions.
THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE
SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET FORTH
IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE, INCLUDING IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY LIMITED IN DURATION TO THE
DURATION OF THIS LIMITED WARRANTY.
Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise
remedies in addition to or inconsistent with those stated above.
Manufacturer’s maximum liability, in any event, shall not exceed the documented purchase price of the product paid by the original consumer.
This warranty only applies to units purchased from an authorized retailer and or re-seller.
NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or
exclusions may not apply to you. This limited warranty gives you specific legal rights as set for herein. You may also have other rights which vary
from state to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this
product or the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumerpurchaser prior to discovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment
selling this product in order to obtain performance under this limited warranty.
If you wish to obtain performance of any obligation under this limited warranty, you should write to:
Char-Broil Consumer Relations
P. O. Box 1240
Columbus, GA 31902-1240
Consumer returns will not be accepted unless a valid Return Authorization is first acquired by calling 1-800-241-7548 and then clearly marked
on the outside of the package and the package is shipped freight/postage pre-paid to the address above.
26 • 463460708
Please register your product online at:
www.grillregistration.com
(If you register online, you do not need to send in this registration card.)
PLEASE FILL OUT THIS CARD AND RETURN IT WITHIN 10 DAYS OF PURCHASE. FAILURE TO RETURN MAY AFFECT YOUR WARRANTY COVERAGE. FOR WARRANTY
SERVICE PROOF OF PURCHASE WILL BE REQUIRED. PLEASE KEEP YOUR SALES RECEIPT. THIS WARRANTY IS NON-TRANSFERABLE.
LLENE ESTA TARJETA Y DEVUELVALA DENTRO DE LOS 10 DIAS DE LA COMPRA. SI NO LA DEVUELVE, PUEDE VERSE AFECTADA SU COBERTURA DE GARANTIA.
PARA EL SERVICIO DE GARANTIA ES NECESARIO QUE PRESENTE SU COMPROBANTE DE COMPRA. CONSERVE LA FACTURA. ESTA GARANTIA ES INTRANSFERIBLE.
VEUILLEZ COMPLETER CETTE CARTE ET LA RETOURNER DANS LES 10 JOURS SUIVANT L’ACHAT. LA COUVERTURE DE VOTRE GARANTIE POURRAIT EN ETRE
AFFECTEE SI VOUS NE LE FAITES PAS. POUR OBTENIR LE SERVICE SOUS GARANTIE, UNE PREUVE D’ACHAT DOIT ETRE PRESENTEE. VEUILLEZ CONSERVER
VOTRE FACTURE. LA PRESENTE GARANTIE N’EST PAS TRANSFERABLE.
1 First Name/Nombre/Prénom
Initial/Inicial/Initiale
Last Name/Apellido/Nom de famille
Apt Number/NO de apart./NO d’appt.
Address (number and street)/Dirección (número y calle)/Adresse (numéro et rue)
State/Estado/Province
City/Ciudad/Ville
Zip Code/Código zip/Code postal
Address/Dirección de correo electrónico/Adresse électronique
2 E-mail
If you voluntarily provide us with your email address, you give us permission to use your email address to send you offers that may interest you.
Si nos informa voluntariamente su dirección de correo electrónico, nos da permiso para usarlo a fin de enviarle ofertas que pueden interesarle.
Si vous choisissez de nous fournir votre adresse électronique, vous nous donnez la permission de l’utiliser pour vous faire part d’offres spéciales susceptibles
de vous intéresser.
(Example: your name @ your host.com)
(Ejemplo: su nombre@su host.com)
(Exemple : votre nom@votre hôte.com)
3 Phone Number/Número telefónico/Numéro de téléphone
6 Date of Purchase/Fecha de compra/Date de l’achat
4
7 Store Name/Nombre de la tienda/Nom du magasin
IMPORTANT!/¡IMPORTANTE!/IMPORTANT!
Write Serial Number and Model Number in spaces below.
Escriba en los espacios de abajo el número de serie y el número
de modelo.
Inscrivez le numéro de série et le numéro de modèle dans les
espaces ci-dessous.
8 Purchase Price/Precio de compra/Prix d’achat
$
5
Your Gender/Sexo/Sexe :
9
Which product are your registering?
¿Qué producto está registrando?
Quel produit enregistrez-vous?
1. Gas Grill/Parrilla a gas/Gril au gaz
2. Electric Grill/Parrilla eléctrica/Gril électrique
3. Smoker/Ahumador/Fumoir
4. Charcoal Grill/Parrilla a carbón/Barbecue au charbon
5. Charcoal Smoker/Ahumador a carbón/Fumoir au charbon
6. Outdoor Fireplace/Chimenea para exteriores/Foyer extérieur
7. Cooker/Fryer / Cocina/freidora / Cuiseur/Friteuse
8. Other/Otro/Autre
1.
Male/Masculino/Masculin
.00
2.
Female/Femenino/Féminin
Mail to: / Envíelo a:
Consumer Warranty Service
P. O. Box 1240
Columbus, GA 31902-1240
Thank you for completing this questionnaire. Your answers will help us and other companies reach you with offers that may interest you. If you prefer not to
receive these offers, please check here .
Gracias por completar este cuestionario. Sus respuestas nos ayudarán, a nosotros y a otras compañías, a llegar a usted con ofertas que puedan resultarle
de interés. Si prefiere no recibir estas ofertas, por favor marque aquí .
Merci d’avoir bien voulu remplir ce questionnaire. Vos réponses nous aideront et aideront d’autres compagnies à vous communiquer des offres spéciales
susceptibles de vous intéresser. Si vous préférez ne pas recevoir d’informations concernant ces offres spéciales, veuillez cocher ici .
463460708 • 27
STOP
Should you encounter a problem with our product
CALL US FIRST
Do not return this product to the store.
WE CAN HELP
GRILL SERVICE CENTER
1-800-241-7548
HOURS 8AM-6PM EST Mon-Fri
Please ensure your warranty registration is complete.
Grilling Safety Checklist
Read and understand owners manual.
Never overfill LP cylinder. Overfilled cylinders may cause freeze-up of
regulator.
Check tubes for spider webs. Ensure valves are correctly installed in
burner tubes.
Always ensure control knobs are in OFF position and regulator is
attached to tank BEFORE opening tank valve to avoid low flames.
Perform leak test regularly.
Thank You for Your Purchase!
Char-Broil, LLC • Columbus, GA 31902 • Printed in China
Download PDF

advertising