Product guide | Char-Broil 473721007 Charcoal Grill User Manual

MODEL 473721007 • PRODUCT GUIDE
THIS GRILL IS FOR OUTDOOR USE ONLY.
CAUTION:
Read and follow all safety statements, assembly
instructions, and use and care directions before
attempting to assemble and cook.
INSTALLER/ASSEMBLER:
Leave this manual with consumer.
CONSUMER:
WARNING:
Failure to follow all manufacturer’s instructions
could result in serious personal injury and/or
property damage.
CAUTION:
Some parts may contain sharp edges –
especially as noted in the manual! Wear
protective gloves if necessary.
Keep this manual for future reference.
If you have any questions or need assistance during assembly, please call 1-800-241-7548.
To insure your satisfaction and for follow-up service, register your grill online at www.grillregistration.com
473721007 • 80012665 • 02-14-07
DANGER
If you smell gas:
1.
2.
3.
4.
Shut off gas to the appliance.
Extinguish any open flame.
Open lid.
If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
WARNING
1. Do not store or use gasoline or other
flammable liquids or vapors in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
Call Grill Service Center for Help and Parts
• If you need assistance with your product or warranty parts call
1-800-241-7548. Hours of Service Center Operation are
8:00 A.M. To 6:00 P.M. EST Monday - Friday.
• To order non-warranty replacement parts or accessories
please visit us on the web at www.charbroil. com or call
1-800-241-7548 and one of our friendly and knowledgeable
agents will be glad to assist you.
Installation Safety Precautions
• Use grill only with LP (propane) gas and the regulator/valve
assembly supplied.
• Grill installation must conform with local codes, or in their
absence with National Fuel Gas Code, NFPA 54 / ANSI
Z223.1 and Natural Gas and Propane Installation Code,
CSA B149.1. Handling and storage of LP cylinders must
conform to LP Gas Code NFPA/ANSI 58. Grill is not for use in
or on recreational vehicles and/or boats.
• All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or
National Electrical Code, ANSI / NFPA 70. Keep any
electrical cords and/or fuel supply hoses away from any hot
surfaces.
• This grill is safety certified for use in the United States only. Do
not modify for use in any other location. Modification will result
in a safety hazard.
WARNING
CALIFORNIA PROPOSITION 65
Combustion by-products produced when using this
product contain chemicals known to the State of
California to cause cancer, birth defects, and other
reproductive harm.
Safety Symbols
The symbols and boxes shown below explain what each heading
means. Read and follow all of the messages found throughout
the manual.
DANGER
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
IMPORTANT: Fill out the product record information below.
Model Number
WARNING
Serial Number
WARNING: Indicates an potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
See rating label on grill for serial number.
Date Purchased
CAUTION
For residential use only. Do not use for commercial
cooking.
2 • 473721007
CAUTION
CAUTION: Indicates a potentially hazardous situation or
unsafe practice which, if not avoided, may result in minor
or moderate injury.
TABLE OF CONTENTS
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Grill Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Product Record Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
To insure your satisfaction
and for follow-up service,
register your grill
online at:
www.grillregistration.com
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
WARNING
Do not attempt to repair or alter the
hose/valve/regulator for any “assumed” defect. Any
modification to this assembly will void your warranty
and create the risk of a gas leak and fire. Use only
authorized replacement parts supplied by
manufacturer.
473721007 • 3
USE AND CARE
DANGER
• NEVER store a spare LP cylinder under or near
the appliance or in an enclosed area.
• Never fill a cylinder beyond 80% full.
• An over filled or improperly stored cylinder is a
hazard due to possible gas release from the
safety relief valve.
• If you see, smell or hear gas escaping,
immediately get away from the LP
cylinder/appliance and call your fire department.
• If the above is not followed exactly, a fire causing
death or serious injury may occur.
LP Cylinder
• The LP cylinder used with your grill must meet the
following requirements:
• Use LP cylinders only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)
capacity maximum.
• LP cylinders must be constructed and marked in accordance
with specifications for LP cylinders of the U.S. Department of
Transportation (DOT). See LP cylinder collar for marking.
• LP cylinder valve must have:
• Type 1 outlet compatible with
regulator or grill.
• Safety relief valve.
• UL listed Overfill Protection
OPD Hand Wheel
Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. Use
only LP cylinders equipped with this type of valve.
• LP cylinder must be arranged for vapor withdrawal and include
collar to protect LP cylinder valve. Always keep LP cylinders in
upright position during use, transit or storage.
LP cylinder in upright position for vapor withdrawal
LP (Liquefied Petroleum Gas)
LP Cylinder Removal, Transport and Storage
• Turn OFF all control knobs and LP cylinder valve. Turn coupling
nut counterclockwise by hand only - do not use tools to
disconnect .Loosen cylinder screw beneath bottom shelf, then
lift LP cylinder up and out of cart. Place dust cap on cylinder
valve outlet whenever the cylinder is not in use. Only install the
type of dust cap on the cylinder valve outlet that is provided
with the cylinder valve. Always use cap and strap supplied with
valve. Other types of caps or plugs may result in leakage of
propane. Failure to use dust cap as directed may result in
serious personal injury and/or property damage.
• A disconnected LP cylinder in LP Cylinder Valve
storage or being transported
must have a dust cap installed (as shown).
Do not store an LP cylinder in enclosed spaces
such as a carport, garage, porch, covered
Dust
patio or other building. Never leave an LP cylinder
Cap
inside a vehicle which may become overheated
Retainer Strap
by the sun.
• Do not store an LP cylinder in an area where children play.
4 • 473721007
• LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten
cabbage) so that it can be smelled.
• LP gas is highly flammable and may ignite unexpectedly when
mixed with air.
LP Cylinder Filling
• Use only licensed and experienced dealers.
• LP dealer must purge new cylinder before filling.
• Dealer should NEVER fill LP cylinder more than 80% of LP
cylinder volume. Volume of propane in cylinder will vary by
temperature.
• A frosty regulator indicates gas overfill. Immediately close LP
cylinder valve and call local LP gas dealer for assistance.
• Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.
• To remove gas from LP cylinder, contact an LP dealer or call a
local fire department for assistance. Check the telephone
directory under “Gas Companies” for nearest certified LP
dealers.
LP Cylinder Exchange
Connecting Regulator to the LP Cylinder
• Many retailers that sell grills offer you the option of replacing
your empty LP cylinder through an exchange service. Use only
those reputable exchange companies that inspect, precision fill,
test and certify their cylinders. Exchange your cylinder only
for an OPD safety feature-equipped cylinder as described
in the "LP Cylinder" section of this manual.
1. LP cylinder must be properly secured onto grill. (Refer to
assembly section.)
• Always keep new and exchanged LP cylinders in upright
position during use, transit or storage.
4. Remove the protective cap from LP cylinder valve. Always use
cap and strap supplied with valve.
2. Turn all control knobs to the OFF position.
3. Turn LP cylinder OFF by turning hand-wheel clockwise to a
full stop.
• Leak test new and exchanged LP cylinders BEFORE
connecting to grill.
Off
Clockwise
LP Cylinder Leak Test
For your safety
OPD Hand Wheel
• Leak test must be repeated each time LP cylinder is exchanged
or refilled.
Type 1 outlet with
thread on outside
• Do not smoke during leak test.
• Do not use an open flame to check for gas leaks.
Safety Relief Valve
• Grill must be leak tested outdoors in a well-ventilated area,
away from ignition sources such as gas fired or electrical
appliances. During leak test, keep grill away from open flames
or sparks.
Strap and Cap
• Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below.
Do not use a POL transport plug
(plastic part with external threads)!
It will defeat the safety feature of
the valve.
s Do not use household cleaning agents. Damage to gas
train components can result.
5. Hold regulator and insert nipple into LP
cylinder valve. Hand-tighten the
coupling nut, holding regulator in a
straight line with LP cylinder valve so
as not to cross-thread the connection.
Continued on next page.
Nipple has to be centered
into the LP cylinder valve.
WARNING
If “growing” bubbles appear do not use or move the LP
cylinder. Contact an LP gas supplier or your fire
department!
473721007 • 5
Leak Testing Valves, Hose and Regulator
1. Turn all grill control knobs to OFF.
2. Be sure regulator is tightly connected to LP cylinder.
Str
a
igh
3. Completely open LP cylinder valve by turning hand wheel
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct
before proceeding.
t
Hold coupling nut and regulator
as shown for proper connection
to LP cylinder valve.
4. Brush soapy solution onto areas circled below.
6. Turn the coupling nut clockwise and tighten to a full stop. The
regulator will seal on the back-check feature in the LP cylinder
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the
connection. Tighten by hand only – do not use tools.
NOTE:
If you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!
DANGER
• Do not insert any tool or foreign object into the valve
outlet or safety relief valve. You may damage the valve
and cause a leak. Leaking propane may result in
explosion, fire, severe personal injury, or death.
WARNING
• Outdoor gas appliance is not intended to be installed
in or on a boat.
• Outdoor gas appliance is not intended to be installed
in or on an RV.
• Never attempt to attach this grill to the self-contained
LP gas system of a camper trailer or motor home.
• Do not use grill until leak-tested.
• If a leak is detected at any time, STOP and call the fire
department.
• If you cannot stop a gas leak, immediately close
LPcylinder valve and call LP gas supplier or your fire
department!
6 • 473721007
5. If “growing” bubbles appear, there is a leak. Close LP
cylinder valve immediately and retighten connections. If leaks
cannot be stopped do not try to repair. Call for replacement
parts. Order new parts by giving the serial, model number and
name and part number of items needed (see parts list) to the
Grill Service Center at 1-800-241-7548.
6. Always close LP cylinder valve after performing leak test by
turning hand wheel clockwise.
WARNING
For Safe Use of Your Grill and to Avoid Serious
Injury:
• Do not let children operate or play near grill.
• Keep grill area clear and free from materials that burn.
• Do not block holes in sides or back of grill.
• Check burner flames regularly.
• Use grill only in well-ventilated space. NEVER use in
enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of any
kind.
• Do not use charcoal or ceramic briquets in a gas grill.
(Unless briquets are supplied with your grill.)
• Use grill at least 3 ft. from any wall or surface.
Maintain 10 ft. clearance to objects that can catch fire
or sources of ignition such as pilot lights on water
heaters, live electrical appliances, etc..
• Apartment Dwellers:
Check with management to learn the requirements
and fire codes for using an LP gas grill in your
apartment complex. If allowed, use outside on the
ground floor with a three (3) foot clearance from walls
or rails. Do not use on or under balconies.
• NEVER attempt to light burner with lid closed. A
buildup of non-ignited gas inside a closed grill is
hazardous.
• Never operate grill with LP cylinder out of correct
position specified in assembly instructions.
• Always close LP cylinder valve and remove
coupling nut before moving LP cylinder from
specified operation position.
Safety Tips
s Before opening LP cylinder valve, check the coupling nut for
tightness.
s When grill is not in use, turn off all control knobs and LP
cylinder valve.
s If the outdoor cooking gas appliance is not in use, the gas
must be turned off at the supply cylinder. Storage of an
outdoor cooking gas appliance indoors is permissible only if
the cylinder is disconnected and removed from the appliance.
s Never move grill while in operation or still hot.
s Use long-handled barbecue utensils and oven mitts to avoid
burns and splatters.
s Maximum load for side shelves is 10 lbs.
s The grease cup must be inserted into grease clip and
emptied after each use. Do not remove grease cup until grill
has completely cooled.
s Clean grill often, preferably after each cookout.
s If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.
s The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
s Only use the pressure regulator and hose assembly supplied
with this grill. Replacement pressure regulator and hose
assemblies must be specified or supplied by Char-Broil, LLC.
s If you have a grill problem see the "Troubleshooting Section".
s If the regulator frosts, turn off grill and LP cylinder valve
immediately. This indicates a problem with the cylinder and it
should not be used on any product. Return to supplier!
CAUTION
• Putting out grease fires by closing the lid is not
possible. Grills are well ventilated for safety
reasons.
• Do not use water on a grease fire. Personal injury
may result. If a grease fire develops, turn knobs
and LP cylinder off.
• Do not leave grill unattended while preheating or
burning off food residue on HI. If grill has not been
regularly cleaned, a grease fire can occur that may
damage the product.
473721007 • 7
Burner Flame Check
Ignitor Lighting
s Do not lean over grill while lighting.
1. Open lid. Turn on gas at LP cylinder.
2. Turn LEFT knob to IGNITE.
3. Push Ignitor Button rapidly (up to 5 times) to light. Be sure
burner lights and stays lit.
4. If ignition does NOT occur in 5 seconds, turn the burner
controls OFF, wait 5 minutes and repeat the lighting
procedure.
5. To ignite right burner, turn right knob to .
6. If ignitor does not work, follow match lighting instructions.
After Lighting: Turn knobs to HI position for warm-up. Do not
warm up grill with knobs on IGNITE. Knobs and handle will
become uncomfortably hot if left in IGNITE positions.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
s Do not lean over grill while lighting.
1. Open lid. Turn on gas at LP cylinder.
2. Place lit match into match holder, then into large opening
beneath grill bottom (as shown below).
3. Push in and turn LEFT knob to IGNITE. Be sure burner
lights and stays lit.
4. Light right burner by pushing RIGHT knob in and turning to
IGNITE.
After Lighting: Turn knobs to HI for warm-up.
8 • 473721007
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from HI to LO. You should see a smaller flame in LO
position than seen on HI. Always check flame prior to each use.
If only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
HI
LO
Turning Grill Off
• Turn all knobs to OFF position. Turn LP cylinder off by turning
hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press ignitor button rapidly.
"Click" should be heard and spark seen each time between
collector box or burner and electrode. See "Troubleshooting" if
no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LO position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified by manufacturer.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
s Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
CAUTION
Cleaning the Burner Assembly
SPIDER ALERT!
GAS COLLECTOR
BOX & IGNITOR
BURNER
CONTROL PANEL
SPIDER WEBS
INSIDE VENTURI
VALVE
VENTURI
AIR
SHUTTER
If you notice that your grill is getting hard to light or that the
flame isn’t as strong as it should be, take the time to check and
clean the venturi’s.
LIFT OUT
BURNER ASSEMBLY
REMOVE
BURNER
CLIPS
CLEAN OUT
VENTURI
SPIDER WEBS
INSIDE VENTURI
In some areas of the country, spiders or small insects have been
known to create “flashback” problems. The spiders spin webs, build
nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of
gas to the burner. The backed-up gas can ignite in the venturi behind
the control panel. This is known as a flashback and it can damage
your grill and even cause injury.
To prevent flashbacks and ensure good performance the burner and
venturi assembly should be removed from the grill and cleaned
before use whenever the grill has been idle for an extended period.
Storing Your Grill
• Clean cooking grates.
• Store in dry location.
• Cover grill if stored outdoors. Choose from a variety of grill
covers offered by manufacturer.
• When LP cylinder is connected to grill, store outdoors in a wellventilated space and out of reach of children.
• If the outdoor cooking gas appliance is not in use, the gas must
be turned off at the supply cylinder. Storage of an outdoor
cooking gas appliance indoors is permissible only if the cylinder
is disconnected and removed from the appliance.
• Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
• When removing grill from storage, follow “Cleaning the Burner
Assembly” instructions before starting grill.
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1. Turn gas off at control knobs and LP cylinder.
2. Remove cooking grate and vaporiser bar.
3. Under grill remove grease cup, disconnect ignitor wire and
clips from burner. To remove clips pull down on large end of
clip attached to the valve, turn away from valve, rotate
upward and remove small end of clip from burner tube (A).
4. Inside grill remove burner assembly (B), clean ceramic
portion of electrode with rubbing alcohol and a swab.
5. Clean outside of burner with soap and water. Lay burner
upside down on flat surface, insert garden hose to force
water through tubes. Make sure water comes out of all
burner holes. Open clogged holes with a thin wire. Shake
out excess water and examine holes. Due to normal wear
and corrosion some holes may become enlarged. If any
large cracks or holes are found replace burner.
6. If grill is to be stored, coat burner lightly with cooking oil.
Wrap in protective cover to keep insects out.
7. If not storing grill after cleaning, replace burner into grill
bottom.
8. To reattach clips hold large curved end away from burner
tube, insert small curved end into hole under burner tubes,
turn clip towards valve, snap into place.
VERY IMPORTANT: Burner tubes must reengage valve
openings. See illustration (A).
9. Reattach ignitor wire to electrode.
10. Reposition vaporiser bar and cooking grate. Reattach clean
grease cup to grease clip.
11. Before cooking again on grill, perform a “Leak Test” and
“Burner Flame Check”.
Burner Tube
Valve
A
Correct burner-to-valve engagement
B
473721007 • 9
Food Safety
How To Tell If Meat Is Grilled Thoroughly
Food safety is a very important part of enjoying the outdoor
cooking experience. To keep food safe from harmful bacteria,
follow these four basic steps:
Clean: Wash hands, utensils, and surfaces with hot soapy water
before and after handling raw meat and poultry.
Separate: Separate raw meats and poultry from ready-to-eat
foods to avoid cross contamination. Use a clean platter and
utensils when removing cooked foods.
Cook: Cook meat and poultry thoroughly to kill bacteria. Use a
thermometer to ensure proper internal food temperatures.
Chill: Refrigerate prepared foods and leftovers promptly.
For more information call: USDA Meat and Poultry Hotline at
1-800-535-4555 In Washington, DC (202) 720-3333, 10:00 am4:00 pm EST.
• Meat and poultry cooked on a grill often browns very fast on the
outside. Use a meat thermometer to be sure food has reached
a safe internal temperature, and cut into food to check for
visual signs of doneness.
• Whole poultry should reach 180° F; breasts, 170° F. Juices
should run clear and flesh should not be pink.
• Hamburgers made of any ground meat or poultry should reach
160° F, and be brown in the middle with no pink juices. Beef,
veal and lamb steaks, roasts and chops can be cooked to 145°
F. All cuts of pork should reach 160° F.
• NEVER partially grill meat or poultry and finish cooking later.
Cook food completely to destroy harmful bacteria.
• When reheating takeout foods or fully cooked meats like hot
dogs, grill to 165° F, or until steaming hot.
10 • 473721007
PARTS LIST – Model No. 473721007
Key Qty
Description
Part #
A
B
C
1
1
1
Firebox Assembly ………….......... 80012668
Valve/Hose/Regulator………........ 80009002
Control Panel…………………...... 80012669
D
E
2
1
Control Knob….....…………….…. 80007972
Electrode...................................... 80009004
F
G
1
1
Left Side Shelf.............................. 80012670
Right Side Shelf............................ 80012671
H
I
J
2
1
1
Wheel............................................ 80008000
Leg Assembly, Left........................ 80012672
Leg Assembly, Right...................... 80012673
K 2
Firebox Supports ........................ 80012674
L 1
M 3
N 1
Ignitor..............................................80008322
Front/Rear Panel........................... 80012675
Burner Assembly............................ 80009012
O
P
Q
R
S
T
U
V
W
X
1
1
2
1
1
1
1
1
1
1
Match Holder..................................80009013
Tank Retainer................................. 80009014
Leg Extender..................................80012682
Lid Assembly.................................. 80012676
Wheel Axle.....................................80009016
Grease Cup Clip............................ 80005794
Grease Cup................................... 80000270
Vaporiser Bar................................. 80007982
Cooking Grate............................... 80007983
Swing Away Grid Assembly........... 80007984
Y 1
Lower Hinge Kit............................. 80009017
Z 1
Upper Hinge Kit............................. 80009018
Key Qty
Description
AA
BB
2
3
Firebox Wind Shield..................... 80009019
Tool Hook........................................80007973
CC
DD
1
1
Wire Form, Tank Exclusion............. 80008305
Logo Plate Assembly...................... 80005765
EE
FF
1
1
Handle............................................ 80009021
Valve Heat Shield........................... 80009047
1
1
Product Manual (English).............. 80012665
Product Manual (Spanish)............... 80012666
1
Hardware Pack............................... 80007997
14 #10-24X2" Machine Screw
6 #10-24X1-1/2" Machine Screw
28
34
3
2
26
1
2
2
2
2
Part #
#10-24X1/2" Machine Screw
#10-24 Flange Nut
Hitch Pin
Hinge Pin
Fiber Washer
Large Flat Washer
#6 Sheet Metal Screw
#8-32x1/4" Machine Screw
#10-24 Wing Nut
Insulation Washers
Tools required for assembly: Phillips screwdriver
Estimated assembly time: 35-45 minutes
Certified Grill Parts And Accessories®, Char-Broil and Design®, Char-Broil (Gas Grill Briquettes)®, Char-Diamonds®, Cooking Zone and Design®, Diamond Flame®, Executive Chef®, Faststart®, Flare
Fighter®, FlavorMaster®, Gas Grill Silouette and Design®, H2O Smoker®, Lava Flame®, MasterFlame®, MasterFlame Precision Cooking System®, PowerSpark®, Quantum®, VIP®, PrecisionFlame and
Design®, Sierra®, and TruFlame® are registered Trademarks of the W.C. Bradley Company. Thermos® is a registered trademark of the Thermos Company and its affiliates.
Artisan Collection by Char-Broil ™, C3 and Design™, Char-Broil and Design™, Flame Design™, FlavorTents™, Grill 2 Go™, Grillin’ Stick™, Keeper of the Flame™, Keepers of the Flame™, Natural Grip™,
Outdoor Cooking Collection and Design™, Patio Bistro™, PrecisionFlame™, Pro-Check™, QuickSet Grills and Design™, SmokerTents™, The Big Easy™, The Minute Grill™, The Edge™, The Tuscan
Collection™, and The Urban Grill™ are Trademarks of the W.C. Bradley Company. Universal Grill Parts and Design™ is a trademark of the Thermos Company and its affiliates.
Protected under one or more of the following U.S. Patents: 4,598,692; 4,624,240; 4,747,391; 4,747,391; 4,817,583; 4,924,846; 4,989,579; 5,003,960; 5,076,256; 5,076,257; 5,090,398; 5,109,834; 5,224,676;
5,277,106; 5,421,319; 5,441,226; 5,452,707; 5,458,309; 5,566,606; 5,566,606; 5,579,755; 5,582,094; 5,613,486; 5,649,475; 5,706,797; 5,711,663; 5,765,543; 5,931,149; 5,996,573; 6,095,132; 6,135,104;
6,173,644B1; 6,279,566; 6,397,731; 6,418,923; 6,439,222; 6,523,461; 6,935,327; D282,619; D339,714; D341,292; D343,337; D358,059; D361,466; D364,535; D372,637; D373,701; D377,735; D383,035;
D397,910; D405,643; D405,643; D406,005; D406,009; D413,043; D413,229; D413,229; D414,982; D415,388; D416,164; D416,441; D416,441; D417,587; D422,516; D423,274; D423,876; D428,303; D435,396;
D436,004; D438,059; D438,060; D438,427; D439,110; D442,505; D443,179; D443,354; D447,384; D447,385; D447,909; D448,610; D448,614; D448,615; D448,616; D448,975; D449,492; D451,759; D456,202S;
D460,313, D461,359 and D504,048. Canada: 87743; 87744; 92607; 92608 and 1,316,424. Other Patents Pending. Assembly instructions © 2006.
473721007 • 11
PARTS DIAGRAM – Model No. 473721007
DD
Z
Z
R
X
W
N
V
Y
EE
Y
A
AA
G
AA
T
C
K
U
FF
E
K
L
B
D
BB
F
I
M
P
CC
O
M
J
Q
H
H
M
S
12 • 473721007
Q
ASSEMBLY – Model No. 473721007
1
Position leg assemblies as shown below. Lay lower front panel between legs. Attach lower front panel to legs using four
#10-24 X1/2" machine screws. Slip firebox supports onto legs making sure the firebox support with match light holder is
on right.
all
until Step 8.
Firebox Support
80012674
Match Holder
80009013
#10-24 X 1/2"
Machine Screw
Qty. 4
Hole on top
Firebox Support
80012674
Front
Leg Assembly, Left
80012672
Leg assembly, Right
80012673
2
Front Panel
80012675
Attach upper front panel to legs using four #10-24 X1/2" machine screws. Secure firebox supports to legs using
four #10-24 X 2" machine screws and four #10-24 flange nuts
Front Panel
80012675
#10-24 X 1/2"
Machine Screw
Qty. 4
Holes
#10-24 X 2”
Machine Screw
Qty. 4
#10-24 Flange Nuts
Qty. 4
473721007 • 13
3
Turn cart assembly over and attach lower rear panel to legs using four #10-24 X1/2" machine screws.
#10-24 X ½”
Machine Screw
Qty. 4
Rear Panel
80012675
Hole on
top
Leg Assembly, Left
80012672
4
Leg Assembly, Right
80012673
Turn cart upside down, install leg extenders. Insert wheel axle through legs and wheels and secure with large flat washer and hitch pin.
1” Hitch Pin
Qty. 1
Leg Extender
80012682
Large Flat
Washer
Qty. 1
Wheel Axle
80009016
“Cone“ side
of wheel
against leg
Hitch
Pin
Wheel
80008000
Large Flat
Washer
14 • 473721007
5
Place cart in upright position. Attach tank exclusion rod using two #10-24 X1/2" machine screws and two #10-24 flange nuts.
#10-24 X ½”
Machine Screw
Qty. 2
#10-24 Flange Nuts
Qty. 2
Wire Form Tank
Exclusion Rod
80008305
6
Attach left side shelf to cart assembly using four #10-24X2" machine screws and four #10-24 flange nuts.
Left Side Shelf
80012670
#10-24 X 2”
Machine Screw
Qty. 4
#10-24
Flange Nut
Qty: 4
473721007 • 15
7
Attach right side shelf to cart assembly using four #10-24X2" machine screws and four #10-24 flange nuts.
Right Side Shelf
80012671
#10-24 X 2”
Machine Screw
Qty. 4
#10-24
Flange Nut
Qty: 4
8
Attach control panel to cart using two #10-24X2" and two #10-24X1-1/2" machine screws and four #10-24 flange nuts.
T
"ALL"
when the control panel is
#10-24
Flange Nut
Qty: 4
#10-24 X 1-1/2”
Machine Screw
#10-24 X 1-1/2”
Machine Screw
Qty. 2
Control Panel
80012669
#10-24 X 2”
Machine Screw
Qty. 2
#10-24 X 2”
Machine Screw
16 • 473721007
9
Attach valve\hose\regulator assembly to control panel using two #10-24 X1/2" machine screws. Attach ignitor to control panel using
a stamped nut.
Ignitor
80008322
#10-24 X ½”
Machine Screw
Qty. 2
Stamped Nut
Valve/Hose/Regulator
80009002
10
Attach two wind shields to firebox assembly using two #10-24 X1/2” machine screws, fiber washers and #10-24 flange nuts on each
side. Attach valve heat shield using two #6 sheet metal screws.
#10-24X1/2’
Machine Screw
Qty: 4
#10-24
Flange Nut
Qty: 4
Firebox Assembly
80012668
#6 Sheet Metal Screw
Qty: 2
Firebox
Windshield
80009019
Fiber Washer
Qty: 4
Valve Heat
Shield
80009047
Firebox
Windshield
80009019
473721007 • 17
11
Place firebox on cart by aligning valves into burner tubes. Make sure burner tubes and valves are correctly engaged (A) before attaching
firebox to cart. Secure firebox to cart using four #10-24X1-1/2" machine screws, fiber washers and #10-24 flange nuts (B).
#10-24
Flange Nut
Qty: 4
Fiber Washer
Qty: 4
A
Burner Tube
Valve
#10-24X1-1/2”
Machine screw
Qty: 4
Correct burner-to-valve engagement
B
Feed ignitor wire through firebox hole. Attach electrode to burner with #8-32x1/4". Attach ignitor wire to ignitor.
12 NOTE:
Ignitor wire must not come into contact with firebox.
#8-32x1/4"
Machine Screw
Qty: 2
Electrode
80009004
Ignitor Wire
18 • 473721007
13
Attach lower lid hinges to back of firebox using two #10-24X1/2" machine screws, fiber washers and #10-24 flange nuts
per hinge. Center flat portion of hinge should be on bottom (see inset below).
#10-24X1/2”
Machine Screws
Qty: 4
#10-24 Flange Nuts
Qty: 4
Fiber Washer
Qty: 8
Lower Lid Hinge
80009017
Center flat portion of hinge on bottom
Attach handle to front of lid using insulation washers, fiber washers and #10-24 wing nuts. Attach upper lid hinges to back of lid using
14 installed.
two #10-24X1/2" machine screws, fiber washers and #10-24 flange nuts per hinge. Hinges should curve downward when properly
#10-24
Wing Nut
Qty: 2
#10-24X1/2’
Machine Screw
Qty: 4
Handle
80009021
#10-24
Flange Nut
Qty: 4
Fiber Washer
Qty: 10
Insulation
Washer
Insulation Washer
Qty:2
Fiber Washer
Wing Nut
Upper Hinge Kit
80009018
473721007 • 19
15
Place lid assembly onto firebox, aligning hinges. Hinges on lid fit inside hinges on firebox. Secure using two hinge pins and hitch
pins.
Lid Assembly
80012676
Hinge Pin
Qty. 2
1” Hitch Pin
Qty. 2
16
Place vaporiser bar onto the two pins on each side inside the firebox. Place cooking grate onto firebox. Attach knobs to valve stems.
Cooking Grate
80007983
Vaporiser Bar
80007982
Knob
80007972
20 • 473721007
17
Insert ends of Swing Away pivot wire into holes in sides of grill lid. Insert ends of Swing Away leg wire into holes in sides of firebox.
NOTE: Pivot and leg wires, running side-to-side, should be under wires running front-to-back. If pivot and leg wires are on top, Swing
Away is installed upside-down.
Swing Away Grid Assembly
80007984
Pivot
Wire
Leg Wire
18
Hang grease cup clip from bottom of firebox and place grease cup into grease cup clip.
Grease Cup Clip
80005794
Grease Cup
80000270
CAUTION
Failure to install grease clip and cup
will cause hot grease to drip from
bottom of grill with risk of fire or
property damage.
473721007 • 21
19
Attach tool hooks to the right side shelf.
Tool Hooks
80007973
22 • 473721007
20
LP CYLINDER IS SOLD SEPARATELY. Fill and leak check
the cylinder before attaching to grill and regulator (see Use &
Care section). Once cylinder has been filled and leak
checked, place cylinder into notches in tank support bracket.
Make sure cylinder valve is facing front of grill. Slide tank
retainer wire over cylinder collar and tighten tee knob.
Regulator hose should be above side support brace. See
Use & Care section of this manual to perform the
“Burner Flame Check” and for important safety
instructions before using.
CAUTION
Cylinder valve must face to front of cart once
tank is attached. Failure to install cylinder
correctly may allow gas hose to be damaged
in operation, resulting in the risk of fire.
Correctly Installed
LP cylinder.
Regulator
LP Cylinder
(not included)
Always keep LP cylinders in
upright position during use,
transport, and storage.
473721007 • 23
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.
Emergencies
Possible Cause
Prevention/Solution
Gas leaking from
cracked/cut/burned
hose.
• Damaged hose.
• Turn off gas at LP cylinder or at source on natural gas systems. If
anything but burned, replace valve/hose/regulator. If burned,
discontinue use of product until a plumber has investigated cause
and corrections are made.
Gas leaking from LP
cylinder.
• Mechanical failure due to rusting or
mishandling.
• Replace LP cylinder.
Gas leaking from LP
cylinder valve.
• Failure of cylinder valve from
mishandling or mechanical failure.
• Turn off LP cylinder valve. Return LP cylinder to gas supplier.
Gas leaking between
LP cylinder and
regulator connection.
• Improper installation, connection not
tight, failure of rubber seal.
• Turn off LP cylinder valve. Remove regulator from cylinder and
visually inspect rubber seal for damage. See LP Cylinder Leak Test
and Connecting Regulator to the LP Cylinder.
Fire coming through
control panel.
• Fire in burner tube section of burner due
to blockage.
• Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After fire is out and grill is cold, remove
burner and inspect for spider nests or rust. See Natural Hazard
and Cleaning the Burner Assembly pages.
Grease fire or
continuous excessive
flames above cooking
surface.
• Too much grease buildup in burner area.
• Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After cooling, clean food particles and
excess grease from inside firebox area, grease cup, and other
surfaces.
Possible Cause
Prevention/Solution
GAS ISSUES:
• Trying to light wrong burner.
• See instructions on control panel and in Use and Care section.
• Burner not engaged with control valve.
• Make sure valves are positioned inside of burner tubes.
• Obstruction in burner.
• Ensure burner tubes are not obstructed with spider webs or other
matter. See cleaning section of Use and Care.
• No gas flow.
• Make sure LP cylinder is not empty. If LP cylinder is not empty,
refer to “Sudden drop in gas flow.”
• Vapor lock at coupling nut to LP cylinder.
• Turn off knobs and disconnect coupling nut from LP cylinder.
Reconnect and retry.
• Coupling nut and LP cylinder valve not
fully connected.
• Turn the coupling nut approximately one-half to three-quarters
additional turn until solid stop. Tighten by hand only - do not use
tools.
Troubleshooting
Problem
Burner(s) will not light
using ignitor.
Continued on next
page.
ELECTRICAL ISSUES:
• Electrode cracked or broken; “sparks at
crack.”
24 • 473721007
• Replace electrode(s).
• Electrode tip not in proper position.
Main Burners:
• Tip of electrode should be pointing toward gas port opening on
burner. The distance should be 1/8” to 1/4”. Adjust if necessary.
Sideburner (if featured):
• Tip of electrode should be pointing toward gas port opening on
burner. the distance should be 1/8” to 3/16”. Adjust if necessary.
• Wire and/or electrode covered with
cooking residue.
• Clean wire and/or electrode with rubbing alcohol and clean swab.
• Wires are loose or disconnected.
• Reconnect wires or replace electrode/wire assembly.
• Wires are shorting (sparking) between
ignitor and electrode.
• Replace ignitor wire/electrode assembly.
Troubleshooting (continued)
Problem
Possible Cause
Prevention/Solution
Burner(s) will not light
using ignitor.
PIEZO PUSH-BUTTON AND ROTARY:
• Push-button sticks at bottom.
• Replace ignitor.
• Rotary knob rotates without clicking.
• Replace knob.
• Sparking between ignitor and electrode.
• Inspect wire insulation and proper connection. Replace wires if
insulation is broken.
Burner(s) will not
match light.
• See “GAS ISSUES:” on previous page.
• Match will not reach.
• Use long-stem match (fireplace match).
• Improper method of match-lighting.
• See “Match-Lighting” section of Use and Care.
• Out of gas.
• Check for gas in LP cylinder.
• Excess flow valve tripped.
• Turn off control and tank knobs, wait 30 seconds, turn tank knob on
slowly, light grill. If flames are still low, turn off control and tank
knobs and disconnect regulator. Reconnect regulator, turn tank knob
on slowly, light grill.
• Vapor lock at coupling nut/LP cylinder
connection.
• Turn off control and tank knobs and disconnect regulator. Reconnect
regulator, turn on tank knob slowly, light grill.
• High or gusting winds.
• Turn front of grill to face wind or increase flame height.
• Low on LP gas.
• Refill LP cylinder.
• Excess flow valve tripped.
• Refer to “Sudden drop in gas flow” above.
• Grease buildup.
• Clean burners and inside of grill/firebox.
• Excessive fat in meat.
• Trim fat from meat before grilling.
• Excessive cooking temperature.
• Adjust (lower) temperature accordingly.
Persistent grease fire.
• Grease trapped by food buildup around
burner system.
• Turn knobs to OFF. Turn gas off at LP cylinder. Leave lid in position
and let fire burn out. After grill cools, remove and clean all parts.
Flashback...
(fire in burner tube(s)).
• Burner and/or burner tubes are blocked.
• Turn knobs to OFF. Clean burner and/or burner tubes. See burner
cleaning section of Use and Care.
Unable to fill LP
cylinder.
• Some dealers have older fill nozzles
with worn threads.
• The worn nozzles don’t have enough “bite” to engage the valve. Try
a second LP dealer.
Low flame, drop in gas
flow.
Flames blow out.
Flare-up.
473721007 • 25
LIMITED WARRANTY
Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after
correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase.
The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid, by the consumer, for review and
examination.
1 Year LIMITED warranty
Upon consumer supplying proof of purchase as provided herein, Manufacturer will repair or replace the parts listed below which are proven
defective during the applicable warranty period. Parts required to complete such repair or replacement shall be free of charge to you except for
shipping costs. The original consumer-purchaser will be responsible for all shipping charges of parts replaced under the terms of this
limited warranty.
This limited warranty is applicable in the United States and Canada only, is only available to the original owner of the product and is not
transferable. Manufacturer requires reasonable proof of your date of purchase. Therefore, you should retain your sales slip or invoice and register
your new product immediately. Defective or missing parts subject to this limited warranty will not be replaced without registration or proof of purchase.
Register online at http://www.charbroil.com or complete and return via mail the Product Registration Card located on the last page of the Use & Care
manual included with this product and retain your sales receipt for proof of purchase.
This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents, corrosions
or discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or the
discoloration of stainless steel surfaces.
This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage.
If an original replacement part is not available, a comparable replacement part will be sent. You will be responsible for all shipping charges of
parts replaced under the terms of this limited warranty.
ITEMS MANUFACTURER WILL NOT PAY FOR:
1. Service calls to your home.
2. Repairs when your product is used for other than normal, single-family household or residential use.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with
electrical or plumbing codes, or use of products not approved by the manufacturer.
4. Any food loss due to product failures.
5. Replacement parts or repair labor costs for units operated outside the United States or Canada.
6. Pickup and delivery of your product.
7. Repairs to parts or systems resulting from unauthorized modifications made to the product.
8. The removal and/or reinstallation of your product.
9. Shipping cost, standard or expedited, for warranty and replacement parts.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
Repair or replacement of defect parts is your exclusive remedy under the terms of this limited warranty. Manufacturer will not be responsible for
any consequential or incidental damages arising from the breach of either this limited warranty or any applicable warranty, or for failure or damage
resulting from acts of God, improper care and maintenance, grease fire, accident, alteration,
replacement of parts by anyone other than Manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather,
acts of nature, animal tampering), improper installation or installation not in accordance with local codes or printed manufacturer instructions.
THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE
SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET FORTH
IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE, INCLUDING IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY LIMITED IN DURATION TO THE
DURATION OF THIS LIMITED WARRANTY.
Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise
remedies in addition to or inconsistent with those stated above.
Manufacturer’s maximum liability, in any event, shall not exceed the documented purchase price of the product paid by the original consumer.
This warranty only applies to units purchased from an authorized retailer and or re-seller.
NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or
exclusions may not apply to you. This limited warranty gives you specific legal rights as set for herein. You may also have other rights which vary
from state to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this
product or the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumerpurchaser prior to discovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment
selling this product in order to obtain performance under this limited warranty.
If you wish to obtain performance of any obligation under this limited warranty, you should write to:
Char-Broil Consumer Relations
P. O. Box 1240
Columbus, GA 31902-1240
Consumer returns will not be accepted unless a valid Return Authorization is first acquired by calling 1-800-241-7548 and then clearly marked
on the outside of the package and the package is shipped freight/postage pre-paid to the address above.
26 • 473721007
Please register your grill online at:
WWW.GRILLREGISTRATION.COM
(If you register online, you do not need to send in this registration card.)
La parrilla estaba ensamblada
Chimenea
/ Envíelo a:
473721007 • 27
STOP
Should you encounter a problem with our product
CALL US FIRST
Do not return this product to the store.
WE CAN HELP
GRILL SERVICE CENTER
1-800-241-7548
HOURS 8AM-6PM EST Mon-Fri
Please ensure your warranty registration is complete.
Grilling Safety Checklist
Read and understand owners manual.
Never overfill LP cylinder. Overfilled cylinders may cause freeze-up of
regulator.
Check tubes for spider webs. Ensure valves are correctly installed in
burner tubes.
Always ensure control knobs are in OFF position and regulator is
attached to tank BEFORE opening tank valve to avoid low flames.
Perform leak test regularly.
Thank You for Your Purchase!
Char-Broil, LLC • Columbus, GA 31902 • Printed in China
Download PDF

advertising