User manual | Chauvet Digital Camera Digital Camera User Manual

Snapshot
LED Mushroom
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
Autoswitching
Power Supply
Replaceable
Fuse
User Serviceable
Duty Cycle
User Manual
3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
TABLE OF CONTENTS
1. BEFORE YOU BEGIN ................................................................................................................................................... 3
WHAT IS INCLUDED ................................................................................................................................................................................ 3
UNPACKING INSTRUCTIONS .................................................................................................................................................................... 3
MANUAL CONVENTIONS ......................................................................................................................................................................... 3
ICONS .................................................................................................................................................................................................. 3
SAFETY INSTRUCTIONS .......................................................................................................................................................................... 4
2. INTRODUCTION ........................................................................................................................................................... 5
FEATURES ............................................................................................................................................................................................ 5
DMX CHANNEL SUMMARY ..................................................................................................................................................................... 5
PRODUCT OVERVIEW............................................................................................................................................................................. 6
3. SETUP .......................................................................................................................................................................... 7
FUSE REPLACEMENT ............................................................................................................................................................................. 7
MOUNTING............................................................................................................................................................................................ 7
Orientation ................................................................................................................................................................ 7
Rigging ..................................................................................................................................................................... 7
FIXTURE LINKING................................................................................................................................................................................... 8
Data Cabling ............................................................................................................................................................. 8
DMX Data Cable ....................................................................................................................................................... 8
Cable Connectors ..................................................................................................................................................... 8
3-Pin to 5-Pin Conversion Chart ................................................................................................................................ 9
Setting up a DMX Serial Data Link ............................................................................................................................ 9
4. OPERATING INSTRUCTIONS .................................................................................................................................... 10
OPERATION ........................................................................................................................................................................................ 10
Stand-Alone Mode (Sound-Active, Auto Mode): ...................................................................................................... 10
DMX Mode .............................................................................................................................................................. 10
DMX CHANNEL VALUES ...................................................................................................................................................................... 10
SETTING THE STARTING ADDRESS ........................................................................................................................................................ 11
DMX QUICK REFERENCE CHART ......................................................................................................................................................... 12
5. APPENDIX .................................................................................................................................................................. 13
DMX PRIMER ..................................................................................................................................................................................... 13
GENERAL MAINTENANCE...................................................................................................................................................................... 13
RETURNS PROCEDURE ........................................................................................................................................................................ 14
CLAIMS .............................................................................................................................................................................................. 14
GENERAL TROUBLESHOOTING .............................................................................................................................................................. 15
CONTACT US ...................................................................................................................................................................................... 16
TECHNICAL SPECIFICATIONS ................................................................................................................................................................ 16
LED Mushroom™ User Manual
2
7/24/2009 4:35 PM
1. BEFORE YOU BEGIN
What is included




1 x LED Mushroom™
1 x Power Cord
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Manual Conventions
CHAUVET manuals use the following conventions to differentiate certain types of information from
the regular text.
MEANING
CONVENTION
[10]
A DIP switch to be configured
<Menu>
A key to be pressed on the fixture’s control panel
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
MENU > Settings
ON
A menu option not to be modified (for example, showing the operating mode/current status)
A sequence of menu options to be followed
A value to be entered or selected
Icons
This manual uses the following icons to indicate information that requires special attention on the part
of the user.
MEANING
ICONS
This paragraph contains critical installation, configuration or operation information. Failure
to comply with this information may render the fixture partially or completely inoperative,
cause damage to the fixture or cause harm to the user or technician.
This paragraph contains important installation or configuration information. Failure to
comply with this information may prevent the fixture from functioning correctly.
This paragraph contains useful, although not critical, information.
LED Mushroom™ User Manual
3
7/24/2009 4:35 PM
Safety Instructions
Please read these instructions carefully. It includes important
information about the installation, usage and maintenance of this
product.
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to
rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher
than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.
Do not daisy chain power to more than 37 units.
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
LED Mushroom™ User Manual
4
7/24/2009 4:35 PM
2. INTRODUCTION
Features
2-channel DMX LED derby effect
Continuous rotation or back and forth motor control
Built-in automated programs via DMX
Built-in sound activated programs via DMX
Additional Features
High-power 3 W, 730 mA LEDs
Linkable with Kinta™ X and Double Derby™ X
Additional power output: max 37 units
DMX Channel Summary
CHANNEL FUNCTION
1
Control/Operating Mode
2
Motor rotation
LED Mushroom™ User Manual
5
7/24/2009 4:35 PM
Product Overview
DMX Out
Dipswitches
DMX In
Sound
sensitivity
adjustment
Power
In
Power link
out
Hanging/mounting
bracket
Bracket
adjustment
knob
LED Mushroom™ User Manual
6
7/24/2009 4:35 PM
3. SETUP
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
Fuse Replacement
With a flat head screwdriver wedge the fuse
holder out of its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Insert the fuse holder back in
its place and reconnect power.
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
Mounting
Orientation
This fixture may be mounted in any safe position, provided there is adequate room for ventilation.
Rigging
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of
the fixture by loosening both knobs and tilting the fixture. After finding the
desired position, retighten both knobs.
Hanging Clamp
When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
Safety cables must always be used.
Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
Do not mount more than 3 fixtures with the Xbracket.
Clamp is sold separately.
LED Mushroom™ User Manual
7
7/24/2009 4:35 PM
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures
the data link can support.
Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA485 standard, no more than 32 fixtures should be connected on one data link. Connecting
more than 32 fixtures on one serial data link without the use of a DMX optically-isolated
splitter may result in deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX Data Cable
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable must
have the following characteristics:
Type:
shielded, 2-conductor twisted pair
Maximum capacitance between conductors:
30 pF/ft
Maximum capacitance between conductor and shield:
55 pF/ft
Maximum resistance:
20 ohms/1000 ft
Nominal impedance:
100 ~ 140 ohms
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
1
3
2
DMX connector configuration
COMMON
INPUT
1
3
2
1
3
2
DMX +
DMX
-
OUTPUT
Resistance 120
ohm ¼ W
between pin 2
(DMX -) and pin 3
(DMX +) on the
output of the last
fixture.
To avoid signal transmission
problems and interference, it is
always advisable to connect a DMX
signal terminator.
Do not allow contact between the common and the fixture’s chassis ground. Grounding the
common can cause a ground loop, and your fixture may perform erratically. Test cables with
an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted
to the shield or each other.
LED Mushroom™ User Manual
8
7/24/2009 4:35 PM
3-Pin to 5-Pin Conversion Chart
If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin
adapter. CHAUVET Model No: DMX5M, or DMX5F. The chart below details a proper cable
conversion:
3 PIN TO 5 PIN CONVERSION CHART
Conductor
3 Pin Female (Output)
5 Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - ) signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Not used
Pin 4
Not used
Pin 5
Setting up a DMX Serial Data Link
Universal DMX Controller
1. Connect the (male) 3-pin connector side of
the DMX cable to the output (female) 3-pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female)
3-pin connector to the input connector of
the next fixture consisting of a (male) 3-pin
connector.
This drawing
provides a general
illustration of the
DMX input/output
panel of a lighting
fixture.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code
Description
DMX1.5
DMX Cable 1.5 m/4.9 ft
DMX4.5
DMX Cable 4.5 m/14.8 ft
DMX10
DMX Cable 10 m/32.8 ft
Continue the link
LED Mushroom™ User Manual
9
7/24/2009 4:35 PM
4. OPERATING INSTRUCTIONS
Operation
Stand-Alone Mode (Sound-Active, Auto Mode):
This mode allows a single unit to run to the beat of the music.
1)
Set DIP switches position to Sound Active or Auto Mode.
Mode
Sound Active
DIP switches
1-10= Off
2)
The unit will react to the low frequencies of music via the internal microphone in Sound Active
mode
3)
Use the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in
Sound-Active mode. Turning the knob counterclockwise decreases the sensitivity; turning the
knob clockwise increases the sensitivity.
DMX Mode
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer.
1)
Set dipswitches position to DMX mode.
Mode
DMX
2)
DIP switches
10= On
Use DIP switches 1-9 to set the DMX address.
DMX Channel Values
CHANNEL VALUE
FUNCTION
1
000  014
015  100
101  255
Control/Operating Mode
No function
LEDs on
Auto
2
001  085
086  170
171  255
Motor Rotation
Counter-clockwise motor rotation (Slow ~ Fast)
Clockwise motor rotation (Slow ~ Fast)
Motor rotation right-to-left-to-right (Slow ~ Fast)
Channel 1 will override the motor control channel (channel 2).
LED Mushroom™ User Manual
10
7/24/2009 4:35 PM
Setting the Starting Address
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address"
from 1 to 512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that uses 6 DMX channels and was addressed to start on
DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start addresses
so that the channels used do not overlap, and note the start address selected for future reference.
If this is your first time addressing a fixture using the DMX control protocol, we suggest jumping to the Appendix
Section and reading the heading “DMX Primer”. It contains very useful information that will help you understand
its use.
Set the start address using the group of DIP switches located usually on bottom of the fixture. Each dip switch
has an associated value. Adding the value of each switch in the ON position will provide the start address.
Figuring out which switches to toggle ON given a specific start address can be accomplished by determining
which switch values will add up to the address value, and turning these switches on. Do so by doing the
following:
1)
Determine the largest value switch that is less than the start address. Turn this switch on.
2)
Subtract the value of the switch you just turned on from the starting address number.
3)
Determine the largest value switch that is less than the remainder from the previous subtraction. Turn this
switch on.
4)
Subtract the value of the switch you just turned on from the remainder of the previous subtraction.
5)
Repeat steps three and four until you have a remainder of zero.
Example Starting Address
1
2
4
8
16
1
2
6 5 4
4
7
8
9 8
16
LED Mushroom™ User Manual
32
Address 233
32
Resolving address
using simple math.
3 2 1
ON
OFF
64
= 16
=8
=2
= 26
6 5 4
128
Switch # 5
Switch # 4
Switch # 2
Total
9 8 7
256
Address 24
64
=8
=2
= 10
128
Switch # 4
Switch # 2
Total
256
Address 10
3 2 1
ON
OFF
233 – (128) = 105, Turn ON DIP # 8
105 – (64) = 41, Turn ON DIP # 7
41 – (32) = 9, Turn ON DIP # 6
9 – (8) = 1, Turn ON DIP # 4
1 – (1) = 0, Turn ON DIP # 1
11
DIP SWITCH
1
2
3
4
5
6
7
8
9
(DMX VALUE)
1
2
4
8
16
32
64
128
256
7/24/2009 4:35 PM
DMX Quick Reference Chart
DMX Address Quick Reference Chart
DIP Switch Position
DMX DIP
#9
SWITCH SET
0=OFF
#8
1=ON
#7
X=OFF or ON #6
#1 #2 #3 #4 #5
0 0 0 0 0
1 0 0 0 0
0 1 0 0 0
1 1 0 0 0
0 0 1 0 0
1 0 1 0 0
0 1 1 0 0
1 1 1 0 0
0 0 0 1 0
1 0 0 1 0
0 1 0 1 0
1 1 0 1 0
0 0 1 1 0
1 0 1 1 0
0 1 1 1 0
1 1 1 1 0
0 0 0 0 1
1 0 0 0 1
0 1 0 0 1
1 1 0 0 1
0 0 1 0 1
1 0 1 0 1
0 1 1 0 1
1 1 1 0 1
0 0 0 1 1
1 0 0 1 1
0 1 0 1 1
1 1 0 1 1
0 0 1 1 1
1 0 1 1 1
0 1 1 1 1
1 1 1 1 1
DIP Switch Position
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
DMX
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
LED Mushroom™ User Manual
12
256 288
257 289
258 290
259 291
260 292
261 293
262 294
263 295
264 296
265 297
266 298
267 299
268 300
269 301
270 302
271 303
272 304
273 305
274 306
275 307
276 308
277 309
278 310
279 311
280 312
281 313
282 314
283 315
284 316
285 317
286 318
287 319
Address
7/24/2009 4:35 PM
5. APPENDIX
DMX Primer
There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture
capable of receiving DMX will require one or a number of sequential channels. The user must assign
a starting address on the fixture that indicates the first channel reserved in the controller. There are
many different types of DMX controllable fixtures and they all may vary in the total number of
channels required. Choosing a start address should be planned in advance. Channels should never
overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set
incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power.
Use a vacuum or air compressor and a soft brush to remove dust collected on external
vents.
Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl
Alcohol and a soft lint free cotton cloth or lens tissue.
Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky
or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean
with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days.
Clean the fixture at least every 30/60 days.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
LED Mushroom™ User Manual
13
7/24/2009 4:35 PM
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #).
Products returned without the RMA # will be refused. Call CHAUVET and request an RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to pack fixture properly; any shipping damage resulting from
inadequate packaging is the customer’s responsibility. As a suggestion, proper UPS packing or
double-boxing is always a safe method to use.
CHAUVET reserves the right to use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of paper inside
the box:
1)
Your name
2)
Your address
3)
Your phone number
4)
The RMA #
5)
A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
LED Mushroom™ User Manual
14
7/24/2009 4:35 PM
General Troubleshooting
Applies to
Symptom
Solution(s)
Lights
Foggers
& Snow
Controllers
Dimmers
& Chaser
Auto shut off
Check fan thermal switch reset

Beam is very dim or
not bright
Clean optical system or replace lamp
Check 220/110v switch for proper setting

Breaker/Fuse keeps
blowing
Check total load placed on device
Chase is too slow
Check users manual for speed adjustment



Device has no power
Check for power on Mains.
Check device’s fuse. (internal and/or external)



Fixture is not
responding
Check DMX DIP switch settings for correct addressing
Check DMX cables
Check polarity switch settings

Fixture is on but
there is no
movement to the
audio
Make sure you have the correct audio mode on the
control switches. If audio provided via ¼” jack, make
sure a live audio signal exists
Adjust sound sensitivity knob



Lamps cuts off
sporadically
Possible bad lamp or fixture is overheating.
Lamp may be at end of its life.

Light will not come
on after power failure
Some discharge lamps require a cooling off period
before the electronics in the fixture can kick start it
again, wait 5 to 10 minutes before powering up

Loss of signal
Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power cables
or black lights.



Moves slow
Check 220/110v switch for proper setting

No flash
Re-install bulb, may have shifted in shipping

No laser output
Bounce mirror motor may have shifted during shipping,
readjust

No light output
Check slip ring & brushes for contact
Install bulb
Call service technician

Relay will not work
Check reset switch
Check cable connections
Remote does not
work
Make sure connector is firmly connected to device

Stand alone mode
All Chauvet lighting fixtures featuring stand-alone
functions do not require additional settings, simply
power the fixture and it will automatically enter into this
mode





If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support at the location on the next page.
LED Mushroom™ User Manual
15
7/24/2009 4:35 PM
Contact Us
World Wide
General Information CHAUVET
th
3000 North 29 Court
Hollywood, FL 33020
voice: 954.929.1115
fax:
954.929.5560
toll free:
800.762.1084
Technical Support
CHAUVET
th
3000 North 29 Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax:
954.929.5560 (Attention: Service)
World Wide Web
www.chauvetlighting.com
Technical Specifications
WEIGHT & DIMENSIONS
Length ........................................................................................................................... 12 in (306 mm)
Width............................................................................................................................ 8.1 in (206 mm)
Height .......................................................................................................................... 8.7 in (221 mm)
Weight........................................................................................................................... 5.4 lbs (2.4 kg)
POWER
Autoswitching ..................................................................................................100~240 VAC, 50/60 Hz
Fuse.................................................................................................................................. F 2 A, 250 V
Power Consumption max @ 120 V..................................................................................... 24 W, 0.2 A
Inrush Power @ 120 V ................................................................................................................. 0.5 A
Power Output .................................................................................................................... 37 units max
LIGHT SOURCE
LED.................................................................... 3 x 3 W, 730 mA (1 Red, 1 Green, 1 Blue) 50,000 hrs
PHOTO OPTIC
Coverage Angle ............................................................................................................................ 130°
THERMAL
Maximum ambient temperature ...................................................................................... 104° F (40° C)
CONTROL & PROGRAMMING
Data input ............................................................................................. locking 3-pin XLR male socket
Data output ........................................................................................ locking 3-pin XLR female socket
Data pin configuration ............................................................................ pin 1 shield, pin 2 (-), pin 3 (+)
Protocols .................................................................................................................. USITT DMX512-A
DMX Channels ....................................................................................................................................2
ORDERING INFORMATION
LED Mushroom™..................................................................................................... LEDMUSHROOM
WARRANTY INFORMATION
Warranty ........................................................................................................... 2-year limited warranty
LED Mushroom™ User Manual
16
7/24/2009 4:35 PM
Download PDF

advertising