Chauvet Indoor Furnishings Indoor Furnishings User Manual

Snapshot
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
Auto-ranging
Power Supply
Replaceable
Fuse
User Serviceable
Duty Cycle
USER MANUAL
3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
TABLE OF CONTENTS
1. Before You Begin ...................................................................................................................................... 3
What is included.............................................................................................................................................. 3
Unpacking Instructions .................................................................................................................................... 3
AC Power ........................................................................................................................................................ 3
Safety Instructions .......................................................................................................................................... 4
2. Introduction ............................................................................................................................................... 5
Features .......................................................................................................................................................... 5
DMX Channel Summary ................................................................................................................................. 5
Product Overview ............................................................................................................................................ 6
Product Dimensions ........................................................................................................................................ 7
3. Setup .......................................................................................................................................................... 8
Fuse Replacement .......................................................................................................................................... 8
Fixture Linking................................................................................................................................................. 8
Data Cabling ................................................................................................................................................... 8
DMX Data Cable ............................................................................................................................................. 8
Cable Connectors ........................................................................................................................................... 9
3-Pin to 5-Pin Conversion Chart ..................................................................................................................... 9
Setting up a DMX Serial Data Link.................................................................................................................. 9
Master/Slave Fixture Linking ..........................................................................................................................10
Mounting ........................................................................................................................................................10
Orientation .....................................................................................................................................................10
Rigging ...........................................................................................................................................................10
4. Operating Instructions.............................................................................................................................11
Using the control panel ..................................................................................................................................11
Control Panel Modes & Functions ..................................................................................................................11
Master/Slave & Stand Alone ..........................................................................................................................12
Built in programs detailed...............................................................................................................................12
DMX Control Mode ........................................................................................................................................13
DMX Channel Values .....................................................................................................................................14
General Troubleshooting ...............................................................................................................................15
Contact Us .....................................................................................................................................................15
5. Appendix...................................................................................................................................................16
DMX Primer ...................................................................................................................................................16
General Maintenance .....................................................................................................................................17
Returns Procedure .........................................................................................................................................17
Claims ............................................................................................................................................................17
Technical Specifications ................................................................................................................................18
COLORstrip™ Mini User Manual
2
1/26/2010 2:49 PM
1. BEFORE YOU BEGIN
What is included






1 x COLORstrip™ Mini
2 x Tall Mounting Brackets
2 x Short Mounting Brackets
1 x Power Cord
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
This fixture has an auto-switching power supply that can accommodate a wide range of input
voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage
you are applying is within the range of accepted voltages. This fixture will accommodate between
100V and 240V AC 50-60 Hz. All fixtures must be powered directly off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is
used solely for a 0% to 100% switch.
Warning!
All fixtures must be connected to circuits with a suitable Earth Ground.
COLORstrip™ Mini User Manual
3
1/26/2010 2:49 PM
Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this product?
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
Always disconnect from power source before servicing or replacing fuse and be sure to replace with
same type fuse.
Secure fixture to fastening device using a safety chain.
Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.
Do not daisy chain power to more than 32 units @ 120V, and 60 units @ 230V.
Caution!
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
COLORstrip™ Mini User Manual
4
1/26/2010 2:49 PM
2. INTRODUCTION
Features
4-channel DMX-512 LED linear wash light
Blackout/static/dimmer/strobe
Static colors and RGB color mixing with or without DMX controller
Built-in automated programs via Master/Slave or DMX
Built-in sound active programs via Master/Slave or DMX
ADDITIONAL FEATURES
Additional power output: max 32 units @ 120V
Additional Slave output allows for color-changing runway effect (up to 31 units)
OPTIONS
COLORstrip™ Foot Controller (LED-FS1)
DMX Channel Summary
Blackout and
Static/Flashing colors
CH DESCRIPTION
RGB Mode
Color Fade Mode
CH DESCRIPTION
CH DESCRIPTION
Chase Programs
CH DESCRIPTION
1
DMX: (000~079)
Static Colors
1
DMX: (080~209)
Programs 1 ~ 13
1
DMX: (210~219)
RGB Color Mix
2
No Function
2
Run Speed
2
Red
3
Flash Speed
3
Flash Speed
3
Green
4
No Function
4
Blue
1
DMX: (220~255)
Color Fade and
Auto Run
2
Run/Fade Speed
3
No Function
4
No Function
For a detailed view of DMX values, turn to the DMX Channel Values on page 14.
COLORstrip™ Mini User Manual
5
1/26/2010 2:49 PM
Product Overview
LEDs
Control Panel (rear)
See view below
Mounting Brackets
Foot controller Input
(Optional Accessory LEDFS1)
Power Output
Master/Slave
Output
IEC Power
Connector with
Fuse Holder
DMX Out
Control Panel
Microphone
Sound
Sensitivity
Adjustment
COLORstrip™ Mini User Manual
DMX In
6
1/26/2010 2:49 PM
Product Dimensions
COLORstrip™ Mini User Manual
7
1/26/2010 2:49 PM
3. SETUP
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
Fuse Replacement
1.
With a flat head screwdriver, wedge the
fuse holder out of its housing.
2.
Remove the damaged fuse from its holder
and replace with exact same type fuse.
3.
Insert the fuse holder back in its place, and reconnect power.
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a Master/Slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with
the EIA-485 standard no more than 32 devices should be connected on one data
link. Connecting more than 32 fixtures on one serial data link without the use of a
DMX optically-isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DM X D AT A C AB L E
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable must
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
COLORstrip™ Mini User Manual
8
1/26/2010 2:49 PM
C AB L E CO N N ECT O R S
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
1
3
2
DMX connector configuration
COMMON
INPUT
1
3
2
CAUTION
1
3
2
DMX +
DMX
-
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
OUTPUT
Termination reduces signal errors. To
avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
Do not allow contact between the common and the fixture’s chassis ground.
Grounding the common can cause a ground loop, and your fixture may perform
erratically. Test cables with an ohm meter to verify correct polarity and to make sure
the pins are not grounded or shorted to the shield or each other.
3- PI N T O 5 - PI N CO N V ER S IO N CH ART
Note!
If you use a controller with a 5 pin DMX output connector, you will need to use a 5
pin to 3 pin adapter. CHAUVET Model No: DMX5M, or DMX5F.
The chart below details a proper cable conversion:
3 PIN TO 5 PIN CONVERSION CHART
Conductor
3 Pin Female (output)
5 Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - ) signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Do not use
Pin 4
Do not use
Pin 5
Universal DMX Controller
Setting up a DMX Serial Data Link
1. Connect the (male) 3 pin connector side of
the DMX cable to the output (female) 3 pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female) 3
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code
Description
DMX1.5
DMX Cable 1.5m/4.9ft
Continue the link
COLORstrip™ Mini User Manual
9
1/26/2010 2:49 PM
DMX4.5
DMX10
DMX Cable 4.5m/14.8ft
DMX Cable 10m/32.8ft
Master/Slave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Often, the setup for Master-Slave
and Standalone operation requires
that the first fixture in the chain be
initialized for this purpose via
settings in the control panel.
Secondarily, the fixtures that follow
may also require a slave setting.
Please consult the “Operating
Instructions” section in this manual
for complete instructions for this
type of setup and configuration.
Slave
Slave
Master
Mounting
O RI E NT AT IO N
This fixture may be mounted in any safe position.
RIG G ING
Mount the fixture using, a suitable “C” or “O” type clamp.
Adjust the angle of the fixture by loosening both knobs
tilting the fixture. After finding the desired position, retighten both
knobs.
When selecting installation location, take into consideration fuse
replacement and routine maintenance.
2 clamps must be used with this fixture.
Safety cables must always be used.
Never mount in places where the fixture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.
COLORstrip™ Mini User Manual
10
Hanging Clamp
and
Note!
Clamp is sold separately.
1/26/2010 2:49 PM
4. OPERATING INSTRUCTIONS
The COLORstrip™ Mini is a DMX-512 controllable, dimming white LED strip light fixture made up of
highly efficient and super bright LEDs.
The COLORstrip™ Mini can operate in Stand-Alone, Master/Slave and via DMX-512 control utilizing
4 channels of control.
Using the control panel
MODE
1. Press the MODE button
repeatedly to back out of a
function.
DOWN
ENTER
UP
2. Press the DOWN/UP buttons to toggle or
through values that pertain to that function.
scroll
3. Press ENTER to enter the sub-menus.
Sound
M/S
DMX
Power
Control Panel Modes & Functions
MODE
FUNCTION
PROGRA
4. AAC5. A000t
023
M
000
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
( P ) RUN SPEED
FUNCTION/PROGRAM
000 – 100
000 - 100
000 - 100
000 - 100
000 - 100
000 - 100
000 - 100
000 - 100
000 - 100
000 - 100
000 - 100
Red
Green
Blue
Yellow
Purple
Cyan
White
Color change 1
Color change 2
Color change 3
Color change 4
Color change 5
Automatic
Color change 6
000 - 050
Sequential Chase 1
Sound Active
Sequential Chase 2
051 - 100
Sequential Chase 3
Sequential Chase 4
Sequential Chase 5
Sequential Chase 6
Sequential Chase 7
Red (000-100)
022
Color Fade
000-100
023
Automatic Program (Sound)
COLORstrip™ Mini User Manual
( C ) COLOR
Blackout
RGB
S dAd 6.
( F ) FLASH
SPEED
Green (000100)
Blue (000100)
DMX Channel Addressing
11
1/26/2010 2:49 PM
SYS
Re-initialize fixture
Re-establishes correct number of down-link fixtures for sequential chase runs.
S Aad
Master/Slave & Stand Alone
The Master/Slave mode will allow you to link units in a daisy chain fashion. In this mode, the first unit
in the daisy chain will command all other units following. Stand Alone can simply be achieved by
setting all units to Master. They would no longer be required to be linked in series.
MASTER UNIT Settings
Master/Slave Link
Press the Mode button. Then, by using the
Up/Down buttons, select [
] and press the Enter
button.
Master
output
Select programs
by using the Up/Down
buttons. Press the Enter button.
Some programs have additional controls such as flash
and run speed. Press the Mode button to toggle
additional functions, then use the Up/Down
buttons to change values.
3 Pin XLR DMX cable
Slave
DMX signal output
does not continue
on M/S linked
fixtures.
Refer to the Control Panel Modes & Functions
chart on the previous page.
Slave
SLAVE UNIT Settings
Units that follow the Master unit
will automatically synchronize to
the Master unit. No other
settings are required.
Slave
IMPORTANT INSTRUCTIONS FOR MASTER/SLAVE OPERATION
Turn ON the Master unit last! This will assure that the Master unit will fully detect all linked units, and re-configure its
built-in sequential chase programs to run on the correct number of linked units.
Built in programs detailed
PROGRAM
FUNCTION
OPTIONS
000
Blackout
001-007 Solid flashing colors
008-013 Color chase programs
F = Flash speed
P = Run speed
F = Flash speed
014-020 Sequential color chase patterns Use sound sensitivity rotary knob to adjust sound
level for optimum response or decrease sensitivity
completely to operate in Run speed only
P = Run speed
021
P = Red
RGB (manual color mix)
COLORstrip™ Mini User Manual
12
1/26/2010 2:49 PM
022
F = Green
C = Blue
P = Run speed
Color fade
DMX Control Mode
Operating in a DMX Control mode environment gives the user the greatest flexibility, when it comes
to customizing or creating a show. In this mode, you will be able to control each individual trait of the
fixture and each fixture independently.
Daisy Chain Connection
1.
2.
Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first
fixture.
Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the
input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from
the output, as stated above, to the input of the following fixture and so on.
Universal DMX Controller
DMX Input
DMX Output
3 Pin XLR DMX cable
You can use the
Master/Slave link to
control multiple units as
one DMX device. Read the
instructions on the
following page.
Continue…
DMX mode setup
1. Press the Mode button, until the display reads [SYS]; then, press Enter.
2. Press the Up/Down buttons until the display reads [S
dAd]; then press Enter.
3. Set the DMX address value by using the Up/Down buttons. Press Enter.
4. Press the Mode button.
COLORstrip™ Mini User Manual
13
1/26/2010 2:49 PM
5. Press Enter to make changes permanent.
DMX Channel Values
NOTE!
Please read all instructions carefully on fixture DMX control mode and addressing.
DMX channels 2, 3 and 4 functions are determined by the current settings of channel 1. For example,
while Channel 1 is set between 210 and 219 the following conditions will apply;



Channel
Channel 2 will control the red LEDs
Channel 3 will control the green LEDs
Channel 4 will control the blue LEDs
Value
Function
Ch 2
000  009
010  019
020  029
030  039
040  049
050  059
060  069
070  079
Static Colors
Blackout
Red
Green
Blue
Yellow
Magenta
Cyan
White
080  089
090  099
100  109
110  119
120  129
130  139
Color Changes
Color change 1
Color change 2
Color change 3
Color change 4
Color change 5
Color change 6
140  149
150  159
160  169
170  179
180  189
190  199
200  209
Sequential Color Chases
Color chase 1
Color chase 2
Color chase 3
Color chase 4
Color chase 5
Color chase 6
Color chase 7
210  219
RGB Color Mix
RGB mode
Red
0-100%
220  229
Chase Fade
Fade Speed
0-100%
230  255
Auto Run (sound active only)
1
COLORstrip™ Mini User Manual
Ch 3
Ch 4
Flash Speed
000  249
Sound Active
250  255
Run Speed
Automatic
000  127
Sound Active
128  255
14
Flash Speed
000  249
Sound Active
250  255
Green
0-100%
Blue
0-100%
1/26/2010 2:49 PM
General Troubleshooting
Symptom
Solution(s)
Auto shut off
Check fan thermal switch reset
Breaker/Fuse keeps
blowing
Device has no power
Check total load placed on device
Fixture is not
responding
Fixture is on but there
is no movement to the
audio
Light will not come on
after power failure
Loss of signal
No light output
Check for power on Mains.
Check device’s fuse. (internal and/or external)
Check DMX settings for correct addressing
Check DMX cables
Check polarity switch settings
Make sure you have the correct audio mode on
Adjust sound sensitivity knob
Some discharge lamps require a cooling off period
before the electronics in the fixture can kick start it
again, wait 5 to 10 minutes before powering up
Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power
cables or black lights.
Check fuse
Call service technician
If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support
at the location below.
Contact Us
World Wide
General Information
CHAUVET
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax:
954.929.5560
toll free: 800.762.1084
Technical Support
CHAUVET
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax:
954.929.5560 (Attention: Service)
World Wide Web
www.chauvetlighting.com
COLORstrip™ Mini User Manual
15
1/26/2010 2:49 PM
5. APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
COLORstrip™ Mini User Manual
16
1/26/2010 2:49 PM
General Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a
soft lint free cotton cloth or lens tissue. Apply solution to the cloth or tissue and drag dirt and grime to
the outside of the lens. Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. Clean with
soft cloth using normal glass cleaning fluid. Always dry the parts carefully. Clean the external optics at
least every 20 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).
Products returned without an RMA # will be refused. Call CHAUVET and request RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from
inadequate packaging is the customer’s responsibility. CHAUVET reserves the right to use its own
discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is
always a safe method to use.
Note:
If you are given an RMA #, please include the following information on a piece of
paper inside the box:
1)
Your name
2)
Your address
3)
Your phone number
4)
The RMA #
5)
A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
COLORstrip™ Mini User Manual
17
1/26/2010 2:49 PM
Technical Specifications
WEIGHT & DIMENSIONS
Length ........................................................................................................................... 19 in (484 mm)
Width.............................................................................................................................. 3.8 in (97 mm)
Height .......................................................................................................................... 5.1 in (130 mm)
Weight........................................................................................................................... 3.3 lbs (1.5 kg)
POWER
Autoswitching ..................................................................................................... 100-240VAC 50/60Hz
Fuse...................................................................................................................................... F2A 250V
Power Consumption ...................................................................................... 21W (0.3A) max @ 120V
Inrush Power ....................................................................................................................0.2A @ 120V
Power Consumption ...................................................................................... 23W (0.2A) max @ 230V
Inrush Power ....................................................................................................................0.3A @ 230V
Power Output .................................................................. 32 units max @ 120V, 60 units max @ 230V
COOLING ................................................................................................................ Convection cooled
LIGHT SOURCE
LED.................................................................................... 192 (64 red, 64 green, 64 blue) 100,000hrs
PHOTO OPTIC
Luminance @ 1m ...................................................................................................................... 820 lux
Beam Angle ............................................................................................................................. 37°x33°
Field Angle ............................................................................................................................... 68°x51°
THERMAL
Maximum ambient temperature ........................................................................................ 104°F (40°C)
CONTROL & PROGRAMMING
Data input ............................................................................................. locking 3-pin XLR male socket
Data output ........................................................................................ locking 3-pin XLR female socket
Data pin configuration ............................................................................ pin 1 shield, pin 2 (-), pin 3 (+)
Protocols .....................................................................................................................DMX-512 USITT
DMX Channels ....................................................................................................................................4
ORDERING INFORMATION
COLORstrip™ Mini ................................................................................................ COLORSTRIPMINI
WARRANTY INFORMATION
Warranty ........................................................................................................... 2-year limited warranty
COLORstrip™ Mini User Manual
18
1/26/2010 2:49 PM