User guide | Chevrolet 1999 Corvette Automobile User Manual

TABLE OF CONTENTS
Safe Use Checklist.........................................................4
Registration & Recall.....................................................5
Assistance.......................................................................5
Warnings.........................................................................6
Base Features
Base Overview...........................................................12
Storage Compartment...............................................13
Recline Adjustment....................................................13
LATCH Removal & Storage.......................................14
Shoulder Belt Lockoff.................................................15
Carrier Features
Carrier Overview.........................................................16
Harness Buckle...........................................................18
Chest Clip...................................................................18
Harness Adjuster........................................................18
Handle.........................................................................19
Canopy........................................................................20
Newborn Insert...........................................................21
Head Support.............................................................22
Carrier/Base Attachment...........................................23
Securing Child In Carrier
Child Requirements....................................................24
Changing Harness Height..........................................25
Securing Child in Carrier............................................26
Safety Tips for Securing Child....................................28
Secure Child Checklist...............................................29
Vehicle Information
Unsafe Vehicle Belts...................................................30
Installation Positions...................................................31
Installation with Base
LATCH or Vehicle Belt?...............................................32
Installation Using Vehicle Belt.....................................32
Installation Using LATCH...........................................34
Uninstalling Base...................................................33, 36
Installation without Base............................................37
Installation in Aircraft..................................................38
Cleaning and Maintenance.........................................39
Replacement Parts.......................................................40
1
2
REGISTRATION & RECALL
YOUR CHILD’S SAFETY DEPENDS ON YOU!
You MUST follow the detailed instructions in this User Guide to
ensure the steps below are performed correctly!
Please complete the Registration Card that came with your
Child Restraint and mail it promptly.
Install Child Restraint Rear-Facing
1
Install in Safe Location in Vehicle
2
Ensure Child is in Size Range
3 4
forward facing vehicle seats only
child faces towards rear of vehicle
position with NO frontal airbag
compatible vehicle belts
3
weight – 4-30 lbs (2 and 13.5 kg)
height – 30 inches or less (76cm)
4
5
Secure Child Properly in Carrier
Secure Restraint Properly in Vehicle
5
vehicle belts tight and restraint secure
Carrier securely attached to Base
6
Verify that Recline Angle is Correct
Bubble between arrows
Level Line on Carrier is level with ground.
Child Restraints could be recalled for safety reasons. You must
register this restraint to be reached in a recall. Send your name,
address, and the restraint’s model number and manufacturing
date
to:
Chicco USA, Inc.
1835 Freedom Road
Lancaster, PA 17601
or call 1-877-424-4226
For recall information, call the U.S. Government’s Vehicle Safety
Hotline 1-888-327-4236 (TTY: 1-800-424-9153), or go to www.
NHTSA.gov. Also check the Chicco Web site at www.chiccousa.
com.
correct shoulder strap height
harness snug and chest clip correct
SAFE USE CHECKLIST
6
NEED HELP?
If you have any problems with your Chicco Child Restraint,
or any questions regarding installation or use, please call:
Chicco Customer Service
1-877-424-4226
Please have Model Number available when you call.
The model number can be located on the bottom of the
Child Restraint.
WARNING
Take Time to Read This User Guide
Carefully read and understand all instructions and warnings in
this User Guide. Your child’s safety depends on you knowing how to
setup, install and use this child restraint properly.
Before installing this restraint in a vehicle, be sure to also check the
vehicle owner’s manual for information on child restraint installation.
NEVER allow others to use this Child Restraint until they have
read and understood all instructions in this User Guide. For future
reference, keep this User Guide in storage door at rear of Base.
Make Sure Child Fits This Restraint
ONLY USE this Child Restraint with children who weigh between
4 and 30 pounds (2 and 13.5 kg) and whose height is 30 inches
(76 cm) or less.
DO NOT use this child restraint if top of child’s head is less than 1
inch from top of restraint.
ONLY USE the Newborn Insert for infants who weigh between 4
and 11 pounds (2 and 5 kg).
WARNING
Secure Child Properly
Snugly adjust the harness around your child. A loose harness
could cause the child to be ejected in a sudden stop or crash,
resulting in serious injury or death. A snug strap should not allow any slack. It lies in a relatively straight line
without sagging. It does not press on the child’s flesh or push the child’s
body into an unnatural position.
NEVER use clothing or blankets that interfere with fastening or
tightening the harness. An unsecured child could be ejected in a
sudden stop or crash!
To keep child warm, place a blanket over child and restraint AFTER you
have properly secured child in harness.
ALWAYS check to make sure buckle is securely latched. If buckle
separates, child could be killed or seriously injured.
NEVER leave child unattended.
ALWAYS keep child properly secured in harness whenever child
is in carrier.
DO NOT use Newborn Insert if child weighs more than 11 pounds.
WARNING
Install Restraint Correctly
NEVER place this Child Restraint in a
vehicle position that has a front airbag.
An infant in a rear-facing child restraint could
be killed by an airbag. Refer to vehicle
owner’s manual before installing this restraint
in a seating position with side airbags.
ALWAYS install rear-facing when using this Child Restraint in a
vehicle. Your child could be killed or seriously injured if you install this
restraint forward facing.
Install this Child Restraint in a rear vehicle seat if possible.
According to accident statistics, children are safer when properly
restrained in the rear seating positions rather than in the front seating
positions.
ONLY install this child restraint in forward facing vehicle seats.
NEVER install in rear facing or side facing vehicle seats.
NEVER use restraint in a vehicle seating position where it can not
be secured tightly. A loosely installed child restraint will not protect
your child in a crash.
WARNING
Install Restraint Correctly
ALWAYS secure this Child Restraint with the vehicle’s child
restraint anchorage system (LATCH) if available or with a vehicle belt.
To ensure a correct installation of Child Restraint, you must follow
the step by step instructions in this User Guide.
BEFORE each use, ALWAYS check to make sure restraint is
tightly secured in the vehicle seat.
ALWAYS check for secure
attachment of carrier each time
you use this restraint. After latching
Carrier into Base, lift up on Carrier
to make sure that it is securely
attached to Base. Child could be
killed or seriously injured if Carrier
is not securely latched to Base.
NEVER travel with this Child Restraint unsecured in a vehicle,
even when it is unoccupied. An unsecured child restraint could injure
other occupants in a sudden stop or crash.
ONLY use Chicco KeyFit infant child restraints with Chicco
KeyFit bases.
WARNING
Ensure Child’s Safety When Using Carrier
NEVER Leave Child Unattended!
Suffocation Hazard: Infant carrier can roll over on soft surfaces
and suffocate child. NEVER place carrier on beds, sofas or other
soft surfaces.
Strangulation Hazard: Child can strangle in loose restraint
straps. ALWAYS use harness. NEVER leave child in carrier when
straps are lose or undone.
Fall Hazard: Child’s movements can slide carrier. NEVER place
carrier near edges of counter tops, tables, or other elevated surfaces. Child and carrier might fall.
BE SURE handle is locked in the “carry position” before lifting
carrier by handle. An unlocked handle could move unexpectedly,
causing injury to child.
NEVER place carrier in top of shopping cart.
Carrier will not be secure and could fall causing injury to child.
WARNING
Check Condition of Restraint
DO NOT use this Child Restraint if any of the Harness or LATCH
straps are cut, frayed or damaged in any way.
DO NOT use infant carrier if it is damaged or broken. Call 1-877424-4226 to find out if the damaged part or parts can be replaced.
NEVER modify or disassemble this Child Restraint except as
instructed to in this User Guide.
DO NOT use any accessories, pads or products supplied by
other manufacturers with this Child Restraint. Items not tested with
this restraint could injure your child.
DO NOT use this Child Restraint if it is more than 6 years old. Check manufacturer’s label on underside of Carrier and in recess of
Base for the “Do Not Use After” date.
YOU MUST replace this Child Restraint if it has been involved in
a crash, even if you cannot see visible damage. A damaged child
restraint may not protect your child in a future crash. ALWAYS check buckle and other parts for hot surfaces. A hot
surface could burn child! Cover unoccupied carrier with blanket when
leaving in a vehicle exposed to sunlight.
10
11
BASE OVERVIEW
BASE FEATURES
Storage Compartment
The Storage Compartment is at
the rear of the Base. The User
Guide is stored inside.
a
b
c
d
e
f
g
Recline Foot
Recline Button
Recline Indicator
LATCH Connector
LATCH Release Lever
LATCH Pull Strap
Shoulder Belt Lockoff
h Carrier Attachment Hook
i Pull Strap Storage Pocket
j Storage & User Guide
DO NOT place heavy or
sharp items in the Storage
Compartment. They could fly
out during a sudden stop or
crash, and cause serious injury.
j
i
h
c
Recline Adjustment
f
1
Recline angle may be adjusted
by pushing Recline Buttons while
lifting Base.
1
e
b
2 Angle is correct when entire
Bubble is between arrows. Vehicle MUST be on a level surface
for the Bubble to indicate correctly.
2
g
d
a
12
13
LATCH REMOVAL & STORAGE
SHOULDER BELT LOCKOFF
This Child Restraint can be safely installed using vehicle
belts or LATCH. LATCH is a Child Restraint attachment
system that is standard in most vehicles manufactured
after September 1, 2002. Refer to your vehicle owner’s
manual for details regarding LATCH use in your vehicle.
The Shoulder Belt Lockoff is used when installing the Base using
your vehicle belts. It locks the vehicle shoulder belt in place,
ensuring a stable, secure Base installation.
Removing LATCH:
1 Pull LATCH Connectors out of
storage pockets while lifting up on
LATCH Release Lever.
Storing LATCH:
2 Insert LATCH Connectors into
storage pockets.
3 Pull LATCH Pull Strap to
secure LATCH Connectors.
1 Do not put the shoulder belt
in the locked mode.
1
1
2 With vehicle belt tight, position
the shoulder belt under the
Shoulder Belt Lockoff that is on the
opposite side of the buckle.
2
3
4 Roll LATCH Pull Strap and
store in Pull Strap Storage Pocket.
4
3 Firmly slide shoulder belt
under the lockoff. (Optional: Once
the base is installed tightly, the
shoulder belt can be put in the
locked mode. See vehicle owner’s
manual or label on seat belt for
more information.)
Refer to “Installation Using
Vehicle Belt” on page 32 for
detailed installation instructions.
When not using LATCH, the LATCH Connectors and Pull
Strap MUST be stored properly to allow Carrier to attach
securely to Base.
14
15
2 3
CARRIER OVERVIEW
a
b
c
d
e
f
g
h
i
Release Handle
Harness Strap
Splitter
Side Hook
Harness Adjuster Strap
Lower Slots
f
Middle Slots
Upper Slots
Head Support Fastener Tabs
CARRIER OVERVIEW
a
b
c
d
e
f
g
g
h
a
Carry Handle
Canopy
Handle Button
Neck Pads
Harness Straps
Seat Pad
Adjuster Cover
Head Support
Harness Slots
Chest Clip
Adjuster Strap
h
i
j
k
l
m
n
o
p
Adjuster Button
Buckle
Newborn Insert
Canopy Mount
Easy-access belt path, to use the carrier
without the base.
a
h
i
b
c
b
d
c
p
e
f
i
n
o
j
d
p
g
e
k
16
l
17
m
CARRIER HARNESS FEATURES
Handle has 3 LOCKED positions. To rotate to a new position, press both
buttons near pivot.
Harness Buckle
To release buckle tongues, firmly
press red button on buckle. To fasten,
insert each tongue into buckle, listen
for a click and then tug to verify that it
is latched.
BE SURE handle is
LOCKED in “CARRY” position
before lifting carrier by
handle. An unlocked handle
could move unexpectedly,
causing injury to child.
Check that buckle functions
properly and is kept free of
dirt. For cleaning instructions,
see page 40.
Chest Clip
To separate chest clip, push center
button and pull apart. To fasten, push
together until locked. HANDLE
a
Carry
ALWAYS place handle in
one of the LOCKED positions
when using Child Restraint in
vehicle.
Store
Position chest clip at center of
child’s chest, level with armpits.
Harness Adjuster
a To loosen harness, firmly press
button while pulling out on both
shoulder straps.
b To tighten harness, slowly pull
adjuster strap until harness is snug
around child.
Stand
b
Keep adjuster area clean and free of dirt. DO NOT attempt to
remove adjuster cover or button.
18
NEVER hang toys or other objects from handle when using
child restraint in vehicle. They could seriously injure a child
in a sudden stop or crash.
19
CANOPY
NEWBORN INSERT
To Adjust Canopy, grab bow on both
sides and rotate. Detach fastener tabs
when rotating toward front of carrier.
a To Remove Canopy Fabric, pull
fabric away from Canopy Mount to
expose button. Press button on canopy
mount to release end of bow. Slide
canopy fabric off bow and detach
canopy from rear of pad.
Release bow from canopy
mount on opposite side of carrier
if using carrier without canopy.
a
1
The harness height may
have to be changed to fit your
child. Before using insert, read
the instructions on “Changing
Harness Height” and “Securing
Child in Carrier”
b
To replace canopy, reverse previous
steps.
To extend/retract visor
b To retract the visor, gently push it
downward and allow it to pop up under
the canopy. The canopy must be
extended before attempting to retract
the visor. c To extend the visor, gently pull
it downward from underneath the
canopy and allow it to pop up in its
extended position.
Use Newborn Insert to provide
additional support and ensure
a secure harness fit for smaller
infants.
2
To Install Insert in Carrier
1 Pull End of Buckle through
center slot in insert.
2 Pull Both Harness Straps
over and around side panels. Push
insert firmly into bottom of carrier.
3
Top of insert should always be
BELOW the lower harness slots.
c
3 When properly installed,
the Newborn Insert and harness
should look like drawing.
ONLY USE Insert with infants who weigh between 4 and 11
lbs. NEVER USE Insert if child weighs more than 11 lbs!
20
21
HEAD SUPPORT
CARRIER/BASE ATTACHMENT
Use head support to provide
additional support for a young
infants head. a
1 To secure carrier to base,
align carrier with base and push
firmly into base. Listen for a click.
1
Pull up on Carrier to verify that
it is securely latched.
Head support can be used
with or without newborn insert.
a
b To Install Head Support, pull
Fastener Tabs through slots and
then attach together on underside
of carrier.
b
Fastener Tabs must always
connect through slots ABOVE
the slots used for harness.
2 To release carrier from base,
pull release handle while lifting
carrier out of base.
Be sure to hold carrier securely
with both hands when removing.
NEVER use head support with harness in upper slots.
Head support could interfere with harness adjustment.
22
23
2
CHILD REQUIREMENTS
Child Requirements
Children should ride in a REAR-FACING Child Restraint until
they’re at least 1 year old AND weigh at least 20 lbs.
The Chicco KeyFit 30 Child Restraint can be used rear-facing
up to 30 lbs.
ONLY use this child restraint
if the child meets all of the following
requirements:
1
1
Weight between 4 and 30 pounds
(2 and 13.5 kg).
CHANGING HARNESS HEIGHT
1 With child firmly seated in
carrier, identify correct slots for
harness. Select closest slots AT or
BELOW child’s shoulders.
With child removed and harness
loosened, turn carrier over to
expose splitter. Unhook one strap
from splitter.
2
3 Pull end of loose strap out of
pad and return it back through
correct slot. Do not twist strap.
Height is less than 30 inches
(76 cm).
1
2
3
4 Re-attach strap to splitter. Connection to splitter should look
like illustration.
Top of head is at least 1 inch below top of carrier.
Use Newborn Insert for infants
who weigh between 4 and 11
pounds (2 and 5 kg).
2
2
5 Repeat for other strap. Straps
must be free of twists and securely
fastened to splitter.
4
Check that Harness is secure
and working properly.
6
For premature infants, you must consult the infant’s doctor
before using this Child Restraint. A premature infant may have
difficulty breathing or have other medical problems when
placed in a seated position.
NEVER remove Harness or harness components from Carrier.
DO NOT USE Child Restraint if any part of harness is damaged.
Call 1-877-424-4226 to order a replacement harness.
24
25
SECURING CHILD IN CARRIER
1 Loosen harness by firmly
pressing adjuster button and
pulling forward on both straps.
1
SECURING CHILD IN CARRIER
5 Insert buckle tongues into
buckle. Listen for a click.
5
Tug on tongues to verify that they
are latched.
Press button on buckle to
release buckle tongues.
2
2
Separate chest clip and spread
straps apart. Place child in carrier
in seated position.
6 Snap chest clip together and
slide away from child’s neck before
tightening harness.
3
Child must be resting against back and bottom of carrier.
3
4 Pull harness straps over child’s
shoulders and around their waist.
Make sure that harness slots are AT or 7 Tighten harness by pulling
slowly on adjuster strap until
harness is snug around child.
4
7
a Harness must be snug. If you
can pinch a fold in strap, harness
is too loose.
b Chest Clip must be positioned
at center of child’s chest, level
with armpits.
c Straps must be laying flat,
free of twists and on top of
child’s shoulders.
8
Read the “Safety Tips
for Securing Child” and the
“Secure Child Checklist”
26
6
8 Make sure child is properly
secured.
BELOW top of child’s shoulders.
If harness straps are
not AT or BELOW child’s
shoulders, you must move
harness to proper slots. See
“Changing Harness Height”
on page 25.
Pull excess strap up through buckle
tongues so that harness is snug
around child’s thighs.
27
CLICK!
SAFETY TIPS FOR SECURING CHILD
1 NEVER secure child in carrier
with child dressed in bulky
garments or heavy clothing.
Heavy clothing can prevent harness from 1
SECURE CHILD CHECKLIST
1
Check Height of Harness Slots
1
Harness straps should always
be AT or BELOW child’s shoulders.
being properly tightened around child.
2
Check Position of Chest Clip
Chest clip should be in center
of child’s chest, level with armpits.
If harness is not snug
around your child, child could
be ejected in a sudden stop
or crash resulting in serious
injury or death!
2
2
3
Check Tightness of Harness
Harness must be snug.
Harness is snug when you cannot
pinch a fold in the harness material.
2 To keep child warm, place a
blanket over child AFTER you have
properly secured and tightened
harness around your child. 3
To ensure a better fit for smaller
infants, use the Newborn Insert
and Head Support provided with
this Child Restraint.
3
If you do not secure child
properly, child could be
ejected in a sudden stop or
crash, resulting in serious
injury or death.
3
NEVER use Insert if child
weighs more than 11 pounds!
NEVER place extra padding under or behind the child.
28
NEVER leave child unattended. ALWAYS keep child properly
secured in harness whenever child is in carrier.
29
VEHICLE INFORMATION
This Child Restraint can be securely
installed in most vehicles using the vehicle
seat belts or LATCH. BUT, there are some
vehicle belts and installation positions that
are UNSAFE for use with this Restraint.
Refer to your Vehicle Owner’s
Manual for detailed information about
vehicle belts, LATCH, and preferred
Restraint installation positions.
INSTALLATION POSITIONS
1
2
Accident statistics indicate that
children are safer when properly
restrained in rear seating positions
than in front seating positions. Children 12 and under should ride
in rear seating positions.
The BEST POSITION is one that:
•Is Recommended by Vehicle Owner’s Manual.
•Results in Secure Installation of Restraint.
UNSAFE Vehicle Belts
The following types of vehicle belts MUST
NOT be used to install this Child Restraint:
1
Motorized (automatic) vehicle belts.
2
Door mounted vehicle belts.
3
Lap/Shoulder Belts with 2 retractors,
ONLY install Child Restraint in forward facing vehicle seats.
NEVER install in rear or side facing seats.
3
(unless Lap Belt has a “Lock Mode”).
1 retractor tensions the Lap Belt and
1 tensions the Shoulder Belt.
4
Non-Locking (ELR) Lap Belts.
(Emergency Locking Retractors)
These belts remain loose after
installation and only lock during
a sudden stop or crash.
30
4
AIRBAG WARNING:
NEVER install Child Restraint in a seat with a
Frontal Airbag. DEATH or SERIOUS INJURY
may occur. Refer to your Vehicle Owner’s
Manual for Side Airbag warnings and information.
31
INSTALLATION USING VEHICLE BELT
INSTALLATION USING VEHICLE BELT
LATCH or Vehicle Belt? This Child Restraint can
be safely installed using Vehicle Belts or LATCH.
Use the method that results in the MOST
SECURE installation in your vehicle.
If using Vehicle Lap Belt only
(no Shoulder Belt), make sure
that Lap Belt is LOCKED, and
that free end of Lap Belt is
neatly stored so it DOES NOT
INTERFERE with attachment
of Carrier to Base.
1 Position Base in forward facing
vehicle seat with Recline Foot
against seat back.
2 Adjust Base Angle by pushing
Recline Buttons while lifting Base. Angle is correct when Bubble is
between arrows.
Vehicle must be on a level surface for 1
Route Vehicle Belt through
openings in Base and buckle
the vehicle belt. (Do not put the
shoulder belt in locked mode.)
4 Tighten Vehicle Belt while
pushing Base firmly into vehicle
seat.
5 Secure Vehicle Shoulder Belt
firmly under Shoulder Belt Lockoff,
while keeping tension on Belt. Only
use the lockoff on the opposite
side of the buckle.
3
the Bubble to indicate correctly.
3
CHECK Installation:
a Belts MUST be TIGHT.
b Base MUST be STABLE.
c Bubble MUST be
between arrows.
d Belts & Buckles MUST NOT INTERFERE with attachment of Carrier to Base.
7 Attach Carrier To Base after
properly securing child in Carrier.
6
2
4
5
6
ALWAYS lift up on Carrier
to verify it is properly attached
to the Base.
Uninstalling Base:
Remove Carrier from Base,
unbuckle Vehicle Belt, and remove
Base from vehicle.
7
NEVER travel with Child Restraint unsecured in vehicle.
Passengers may be injured during a sudden stop or crash.
32
33
INSTALLATION USING LATCH
INSTALLATION USING LATCH
5 Tighten LATCH Belts by
pulling up firmly on LATCH Pull
Strap while pressing Base firmly
into vehicle seat.
LATCH or Vehicle Belt? This Child Restraint can
be safely installed using Vehicle Belts or LATCH.
Use the method that results in the MOST
SECURE installation in your vehicle.
1 Remove LATCH Connectors
from storage pockets while lifting
up on LATCH Release Lever.
2 Position Base in forward facing
vehicle seat with Recline Foot
against seat back.
3 Adjust Base Angle by pushing
Recline Buttons while lifting Base. Angle is correct when Bubble is
between arrows.
Vehicle must be on a level surface for the Bubble to indicate correctly.
Attach LATCH Connectors by
pushing them firmly onto vehicle
LATCH Anchor Bars. Verify
connection is secure by pulling
firmly on LATCH straps.
6 Store LATCH Pull Strap neatly
in Pull Strap Storage Pocket.
1
2
3
4
4
5
CLICK!
7 Check Installation
a LATCH belts MUST be TIGHT
b Base MUST be STABLE
c Bubble MUST be
between arrows
d LATCH Pull Strap MUST
NOT interfere with
attachment of Carrier
to Base.
7
Attach Carrier to Base after
properly securing child in Carrier. 8
ALWAYS lift up on Carrier
to verify it is properly attached
to the Base.
8
This child restraint base is designed to be used with lower LATCH
anchors at the standard spacing (11 inches) ONLY! Refer to vehicle owner’s
manual for information about LATCH and child restraint installation positions.
34
6
35
INSTALLATION USING LATCH
Uninstalling Base
Remove Carrier from Base
INSTALLATION WITHOUT BASE
1 Position Carrier rear facing on
vehicle seat, with child properly
secured in Carrier.
1
1 Loosen LATCH by lifting the
LATCH Release Lever and pulling
Base away from vehicle seat back.
2
Route Vehicle Belt under
both Belt Guides, and buckle the
vehicle belt.
2
2
Detach LATCH Connectors
by pressing the red button on each
LATCH Connector, and remove
Base from vehicle.
2
Storing LATCH
Insert LATCH Connectors into
storage pockets. a
3 Tighten Vehicle Belt while
pushing Carrier firmly into
vehicle seat.
A tightly rolled towel may be used 3 4
b
under the front edge of the Carrier if needed for stable, secure installation.
1
Check Installation:
a Level Line on Carrier MUST be LEVEL with ground.
b Vehicle belt MUST be TIGHT.
c Carrier MUST be STABLE
and secure.
4
1 Pull LATCH Pull Strap to
secure LATCH Connectors.
a
Roll LATCH Pull Strap and
store in Pull Strap Storage Pocket.
2
a
2
a
NEVER travel with CHILD RESTRAINT unsecured in vehicle.
Passengers may be injured during a sudden stop or crash.
When not using LATCH, the LATCH Connectors and Pull Strap
MUST be stored properly.
NEVER install CARRIER without Base using a non-locking
ELR vehicle belt. The installation will NOT be secure. Refer to
your vehicle owner’s manual for detailed vehicle belt information.
36
37
INSTALLATION IN AIRCRAFT
CLEANING & MAINTENANCE
This Child Restraint is certified for use in commercial aircraft.
Be sure to contact your airline prior to travel, to discuss their
Child Restraint policy.
Fabrics may be spot-cleaned with mild soap and water, or
machine washed in cold water on delicate cycle using mild
detergent. Hang to dry. DO NOT USE BLEACH.
1 Position Carrier rear facing
in aircraft seat, with child properly
secured in Carrier.
Removing the Seat Pad
Remove Harness Straps from
Harness Slots as described in
“Changing Harness Height.” 2
Route Aircraft Lap Belt under
both Belt Guides, and fasten the
aircraft belt.
1
2
3 Tighten Aircraft Lap Belt
while pushing Carrier firmly into
aircraft seat.
1 Unhook elastic band attached
around handle pivots, and
disconnect chest clip and buckle.
Carefully pull seat pad from
under Adjuster Cover. ADJUSTER
COVER MUST REMAIN IN PLACE. Guide harness assembly through
slots in bottom of seat pad, while
removing from Carrier.
2
3 4
A tightly rolled airline blanket may be used under the front edge of the Carrier if needed for stable, secure installation.
Check Installation:
a Level Line on Carrier MUST be LEVEL with ground.
b Aircraft belt MUST be TIGHT.
c Carrier MUST be STABLE
and secure.
b
4
38
a
Installing the Seat Pad
Reverse the removal instructions to
reinstall the Seat Pad.
Carefully follow instructions in
“Changing Harness Height” to ensure
the harness is properly routed and
adjusted.
39
2
NEVER use Carrier
without the Seat Pad.
CLEANING & MAINTENANCE
NEVER remove Harness or harness components from Carrier.
If harness is extremely soiled or damaged, Call Chicco to order
a replacement.
Cleaning Plastics
Sponge clean using warm water
and mild soap. Towel dry.
DO NOT USE BLEACH,
solvents, or household cleaners, as
they may weaken the plastics.
Replacement Parts
Many replacement
parts are available for
your Child Restraint.
To order replacement
parts, call:
Chicco
Customer Service
1-877-424-4226
Cleaning Harness
and LATCH Straps
Sponge clean using warm water
and mild soap. Air dry.
DO NOT USE BLEACH,
solvents, or household cleaners, as
they may weaken the straps.
Cleaning Buckle
and LATCH Hardware
Sponge clean, or rinse in cup of
warm water.
DO NOT USE ANY SOAPS OR
LUBRICANTS on Buckle or LATCH
Hardware. It may cause them to
malfunction.
40
Please have the
Restraint model
and serial numbers
available to expedite
service.
Download PDF

advertising