Chevrolet 2008 Express Automobile User Manual

PLASMA TV
OWNER’S MANUAL
MODELS:
DU-42PZ60/60A/60B/60C/60K/60R/60S
DU-42PZ60H/60HA/60HB/60HC/60HK/60HR/60HS
DU-42PZ70/70A/70B/70C/70K/70R/70S
DU-42PZ70H/70HA/70HB/70HC/70HK/70HR/70HS
DU-50PZ60/60A/60B/60C/60K/60R/60S
DU-50PZ60H/60HA/60HB/60HC/60HK/60HR/60HS
DU-50PZ70/70A/70B/70C/70K/70R/70S
DU-50PZ70H/70HA/70HB/70HC/70HK/70HR/70HS
Please read this manual carefully and completely before
operating your TV.
Retain this manual for future reference.
Record model number and serial number of the TV in the
spaces provided below.
See the label attached on the back cover and relate this
information to your dealer if you require service.
Model Number :
Serial Number :
LG Electronics U.S.A., Inc.
Warning
Warning
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
1-201-816-2000
http://www.lgusa.com
2 Plasma TV
Safety Instructions
Safety Instructions
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical
shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe
the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation
that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
9. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
2. Follow Instructions
All operating and use instructions should be followed.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered
to.
3. Retain Instructions
The safety and operating instructions should be retained for
future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6. Water and Moisture
Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or on
an unstable cart, stand, tripod, bracket, or table. The product
may slide or fall, causing serious injury to a child or adult,
and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
12. Power-Cord Polarization
This product is equipped with a three-wire grounding type
plug, a plug having a third (grounding) pin. This plug will only
fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.
PORTABLE CART WARNING
Owner’s Manual 3
Safety Instructions
Safety Instructions continued
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so
as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical
Code (U.S.A.), ANSI/ NFPA 70 provides information with
regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Example of Grounding According to National
Electrical Code Instructions
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC - National Electrical Code
15. Lightning
For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
4 Plasma TV
19. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been
damaged.
f. If the product exhibits a distinct change in performance.
21. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer. The product may slide
or fall, causing serious injury to a child or adult, and serious
damage to the product.
24. Heat
The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Contents
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4
Time Menu Options
Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .24
Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .24
On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .24
Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .25
Option Menu Features
Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Caption / Caption Mode . . . . . . . . . . . . . . . . . .27
Caption Option / EZ Demo . . . . . . . . . . . . . . . .28
ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .28
White Wash . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Lock Menu Options
Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .31
PIP (Picture-in-Picture)/Twin Picture
Watching PIP/POP/Twin Picture . . . . . . . . . . . ..32
Selecting an Input Signal Source for PIP/Twin Picture . .32
Swapping PIP/Twin Picture . . . . . . . . . . . . . . . .32
TV Program Selection for PIP . . . . . . . . . . . . . .32
Moving the PIP sub picture . . . . . . . . . . . . . . . .33
Adjusting Main and Sub Picture Sizes for Twin Picture . .33
POP (Picture-out-of-Picture: Channel Scan) . . .33
Introduction
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connection Options . . . . . . . . . . . . . . . . . . . . . .8
Remote Control Key Functions . . . . . . . . . . . . . .9
Installation
Installation Instruction . . . . . . . . . . . . . . . . . . . . . .10
External Equipment Connections . . . . . . . . . .11~15
Antenna Connection . . . . . . . . . . . . . . . . . . . . .11
VCR Setup / Cable TV Setup . . . . . . . . . . . . . .12
External A/V Source Setup . . . . . . . . . . . . . . . .13
Monitor Out Setup / DVD Setup . . . . . . . . . . . .13
HDSTB Setup / Digital Audio Output . . . . . . . . .14
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Operation
Screen Setup for PC mode
Adjustments for screen position, clock, and phase
Turning the TV On . . . . . . . . . . . . . . . . . . . . . .
On-screen Menus Language Selection . . . . . . .
Setup Menu Options
EZ Scan (Channel Search) . . . . . . . . . . . . . .
Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . .
DTV Signal Strength . . . . . . . . . . . . . . . . . . .
Channel Label Setup . . . . . . . . . . . . . . . . . .
Main Picture Source Selection . . . . . . . . . . .
Front LED (Light Emitting Diode) Display . . .
Video Menu Options
EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Picture Control (User Option) . . . . . .
Color Temperature Control . . . . . . . . . . . . . .
Video Preset . . . . . . . . . . . . . . . . . . . . . . . .
Audio Menu Options
Audio Language . . . . . . . . . . . . . . . . . . . . . .
EZ SoundRite / EZ Sound . . . . . . . . . . . . . . .
Manual Sound Control (User Option) . . . . . .
Stereo/SAP Broadcasts Setup . . . . . . . . . . .
Front Surround . . . . . . . . . . . . . . . . . . . . . . .
TV Speakers On/Off Setup . . . . . . . . . . . . . .
. .16
. .17
. .17
.
.
.
.
.
.
.18
.18
.19
.19
.20
.20
.
.
.
.
.21
.21
.21
.21
.
.
.
.
.
.
.22
.22
.22
.23
.23
.23
External Control Device Setup . . . . . . . . . . . . . . . .34~38
IR Codes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39~40
Programming the Remote
Programming Codes
. . . . . . . . . . . . . . . . . . . . . .41
. . . . . . . . . . . . . . . . . . . . . . .42~43
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .44
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47~48
Setup and Operation Checklist
Setup and Operation Checklist
(See pages 11~15 for available connection and operational setup options.)
1. Unpack TV and all accessories.
5. Turn video source equipment on.
2. Connect all external video and audio equipment.
see pages 12 ~ 14.
6. Select viewing source for TV.
See page 20.
3 Install batteries in remote control.
See page 9.
7. Fine-tune source image and sound to your personal preference or as required by source.
See pages 21 ~ 23.
4. Turn TV on.
See page 17.
8. Additional features set up
See Contents above.
After reading this manual, keep it handy for future reference.
Owner’s Manual 5
Introduction
Introduction
What is a Plasma Display Panel (PDP)?
A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality
and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also
be viewed as a series of fluorescent lamps.
How does it work?
PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue.
Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.
You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over
16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5
inches thick.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is
clear and visible to viewers anywhere in the room who can see the screen.
Wide Screen
The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture
feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not
fit.
The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen
The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell
defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be
acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with
cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.
The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the
operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.
6 Plasma TV
Introduction
Controls
- This is a simplified representation of front panel.
Here shown may be somewhat different from your TV.
- This manual explains the features available on the DU-50PZ60/70 series TVs.
Front Panel Controls
Remote Control Sensor
A/V INPUT 2
ON/OFF
Power Button
S-VIDEO
VIDEO
L/MONO AUDIO R
TV/VIDEO
AUDIO Input
Use to connect to hear
stereo sound from an
external device.
MENU
VOL
CH
TV/VIDEO Button
MENU Button
CHANNEL (E,
D)
Buttons
VOLUME (F,G) Buttons
VIDEO Input
Connects the video signal
from a video device.
Power Standby Indicator
Illuminates red in standby mode,
Illuminates green when the TV is
turned on.
S-VIDEO Input
A connection available to provide better
picture quality than the video input.
Owner’s Manual 7
Introduction
Connection Options
Back Connection Panel
DVD/DTV Input (Component 1-2)
Connect a component video/audio device to these jacks.
Digital Audio (DVI: Digital Visual
Interface/Component1) Input/
Digital Audio Output
Connect digital audio from various types
of equipment. Note: In standby mode,
these ports will not work.
Monitor Output
Connect a second TV or
Monitor.
AUDIO INPUT
Antenna1
Antenna 2
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
R AUDIO L
COMPONENT 2
COMPONENT 1
DVD
/DTV
INPUT
VIDEO
R
MONITOR
OUTPUT
A/V
INPUT1
(MONO)
RS-232C INPUT REMOTE
S-VIDEO (CONTROL/SERVICE) CONTROL
L
EXTERNAL SPEAKER
AC INPUT
Audio/Video Input 1
Connect audio/video output from an
external device to these jacks.
RGB Input/Audio Input/DVI Input
Connect the monitor output connector from
a PC to the appropriate input port.
External Speaker (8 ohm Output)
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker &
Speaker Stand’ manual.
Power Cord Socket
This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
- This manual explains the features available on the DU-50PZ60/70 series TVs.
8 Plasma TV
Remote Control Port
Connect your wired remote
control here.
VIDEO INPUT
L
DVI INPUT
DIGITAL AUDIO
(OPTICAL)
Antenna 1-2 Inputs
Connect cable or antenna
signals to the TV, either
directly or through your
cable box. For DTV use
Antenna 2 only.
R
S-Video Input
Connect S-Video out from an S-VIDEO
device to the S-VIDEO input.
Installation
Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the TV.
MODE
Selects the remote operating mode: TV,
VCR, DVD, CABLE, HDSTB or AUDIO.
Select other operating modes, for the
remote to operate external devices.
LIGHT
Illuminates the remote control buttons.
TV/VIDEO
Selects: DTV, Analog, Video1-2,
Component 1-2, RGB-DTV (or RGB-PC),
DVI-DTV (or DVI-PC) input sources.
MODE
LIGHT
COMP/RGB/DVI
Selects: Component 1-2, RGB-DTV (or RGBPC), DVI-DTV (or DVI-PC) input sources.
TV/VID
EO
POWER
COMP/RGB/DVI TIMER
TIMER
Lets you select the amount of time before
your TV turns itself off automatically.
NUMBER buttons
DASH
Used to enter a program number for multiple
program channels such as 2—1,2—2,etc.
FLASHBK
FLASHBK
Tunes to the last channel viewed.
SURF
SURF
Use to scroll the Surf channel list.
MUTE
MUTE
Switches the sound on or off.
VOLUME UP/DOWN
Increases/decreases the sound level.
VOL
THUMBSTICK (Up/Down/Left/Right/OK)
Allows you to navigate the on-screen
menus and adjust the system settings to
your preference.
MENU
Brings up the main menu to the screen.
SOUND
Selects the sound appropriate
for the program's character.
CH
RATIO
SAP
INFO
CC
CHANNEL UP/DOWN
Selects available channels found
with EZ scan.
RATIO
Changes the aspect ratio.
INFO
When you watch the TV, displays information
on top of the screen. Not available in
Component 1-2, RGB and DVI mode.
SAP
Selects MTS sound: Mono, Stereo, and SAP.
Change the audio language in DTV mode.
POWER
Turns your TV or any other programmed
equipment on or off, depending on mode.
OK
CC
Select a closed caption:
Off, EZ Mute, and On.
EXIT
MENU
SOUND
VIDEO
PLAY
PAUSE
STOP RECORD
REW
FF
SKIP
PIP
PIPCH-
PIPCH+
PIPINPUT
FREEZE
ZOOM
SIGNAL
SWAP
ADJUST
FREEZE
Freezes the currently-viewed picture. Main
picture is frozen in PIP/Twin picturre mode.
ADJUST
Adjusts screen position, clock, and
phase in PC mode.
ZOOM
Enlarges the main picture size.
EXIT
Clears all on-screen displays and returns to
TV viewing from any menu.
VIDEO
Adjusts the factory preset picture according
to the room.
VCR/DVD BUTTONS
Control some video cassette recorders or
DVD player ("RECORD" button is not available for DVD player).
PIP
Switches between PIP, POP (Picture-out-ofPicture) and Twin picture modes.
PIPCH-/PIPCH+
Changes to next higher/lower PIP channel.
PIP INPUT
Selects the input source for the sub picture.
SWAP
Exchanges the PIP/main images.
SIGNAL
Displays the digital signal strength.
Installing Batteries
• Open the battery compartment cover on the back side and install the batteries
matching correct polarity (+ with +, - with -).
• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.
Replace cover.
Owner’s Manual 9
Installation
Installation
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer
where you purchased the product.
MODE
LIGHT
TV/VIDEO
POWER
COMP/RGB/DVI TIMER
FLASHBK
MUTE
SURF
VOL
CH
RATIO
SAP
INFO
CC
OK
EXIT
MENU
SOUND
PLAY
REW
1.5V
1.5V
Owner’s Manual
PAUSE
FF
VIDEO
STOP RECORD
SKIP
PIP
PIPCH-
PIPCH+
PIPINPUT
FREEZE
ZOOM
SIGNAL
SWAP
ADJUST
Batteries
Power Cord
75Ω Round Cable
Remote Control
Installation Instructions
• The TV can be installed in various ways such as on a wall, or on a desktop etc.
• The TV is designed to be mounted horizontally. The speakers shown are optional.
GROUNDING
Power
Supply
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.
Short-circuit
Breaker
Desktop Pedestal Installation
Wall Mount: Horizontal installation
For proper ventilation, allow a clearance of 4” on each
side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional
Wall Mounting Bracket Installation and Setup Guide.
For proper ventilation, allow a clearance of 4” on each
side and the top, 2.36” on the bottom, and 2” from the
wall. Detailed installation instructions are included in
the optional Desktop Stand Installation and Setup
Guide available from your dealer.
2 inches
4 inches
4 inches
4 inches
4 inches
4 inches
10 Plasma TV
4 inches
2 inches
4 inches
2.36 inches
Installation
External Equipment Connections
Antenna Connection
Analog and Digital TV signals provided on one antenna
- Antenna or Cable Service without a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
Bronze Wire
Antenna 2
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
DVI INPUT
DIGITAL AUDIO
(OPTICAL)
RF Coaxial Wire (75 ohm)
VHF Antenna
Turn clockwise to tighten.
UHF Antenna
Bronze Wire
Outdoor
Antenna
Be careful not to bend the bronze wire when
connecting the antenna.
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
• In a poor signal area to improve picture quality, purchase
and install a signal amplifier.
Plasma TV
• If the antenna needs to be split for two TV’s, install a “2Way Signal Splitter” in the connections.
na1
Antenna 2
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
DVI INPUT
DIGITAL AUDIO
(OPTICAL)
Signal
Amplifier
• If the antenna is not installed properly, contact your dealer for assistance.
Analog and Digital TV signals provided on two separate antennas
Wall Antenna
Socket
Bronze Wire
RF Coaxial Wire (75 ohm)
Analog Antenna
Wall Antenna
Socket
Turn clockwise to tighten.
Antenna1
Antenna 2
RGB INPUT
AUDIO INPUT
DVI INPUT
RF Coaxial Wire (75 ohm)
Digital Antenna
Bronze Wire
NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches.
The TV will let you know when the analog, cable, and digital channel scans are complete.
Owner’s Manual 11
Installation
NOTE: All cables shown are not included with the TV
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time.
Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may
remain visible on the screen.
Connection Option 1
Set VCR output switch to 3 or 4 and then tune
TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as
shown in the figure.
When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white,
and Audio Right = red).
If you connect an S-VIDEO output from VCR to
the S-VIDEO input, the picture quality is
improved; compared to connecting a regular
VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.)
3. Select the input source with using the
TV/VIDEO button on the remote control. (If
connected to A/V INPUT 1, select Video 1
input source)
VIDEO INPUT
AUDIO INPUT
Antenna 1
DVI
COMPONENT1
INPUT OUTPUT INPUT
Antenna 2
RGB INPUT
AUDIO INPUT
R
R AUDIO L
L
COMPONENT 2
DVD
/DTV
INPUT
DVI INPUT
COMPONENT 1
DIGITAL AUDIO
(OPTICAL)
VIDEO
MONITOR
OUTPUT
A/V
INPUT1
RS-232C INPUT REMOTE
S-VIDEO (CONTROL/SERVICE) CONTROL
(MONO)
1
2
ANT OUT
ANT IN
S-VIDEO
VCR
OUT
OUTPUT
SWITCH
3
4
IN
(R) AUDIO (L)
VIDEO
Do not connect to both Video and
S-Video at the same time.
Cable TV Setup
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.
The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.
- For further information regarding cable TV service, contact your local cable TV service provider(s).
Connection Option 1
1. Select 3 or 4 with channel switch on cable
box.
2. Tune the TV channel to the same selected
output channel on cable box.
3. Select channels at the cable box or with the
cable box remote control.
VIDEO INPUT
AUDIO INPUT
Antenna 1
Antenna 2
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
R
R AUDIO L
L
COMPONENT 2
DVI INPUT
DIGITAL AUDIO
(OPTICAL)
COMPONENT 1
Connection Option 2
1. Connect the audio and video cables from the
Cable Box's output jacks to the TV input jacks,
as shown in the figure.
When connecting the TV to a Cable Box,
match the jack colors (Video = yellow, Audio
Left = white, and Audio Right = red).
2. Select the input source with using the
TV/VIDEO button on the remote control. (If
connected to A/V INPUT 1, select Video 1
input source)
3. Select your desired channel with the remote
control for cable box.
12 Plasma TV
1
2
(R) AUDIO (L)
OUTPUT
SWITCH
3
4
RF
Cable
TV
VCR
Cable Box
VIDEO
DVD
/DTV
INPUT
VIDEO
MONITOR
OUTPUT
A/V
INPUT1
RS-232C INPUT
(MONO)
S-VIDEO (CONTROL/SERVICE)
REMOTE
CONTROL
Installation
External A/V Source Setup
How to connect
Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the
figure.
When connecting the TV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
AUDIO INPUT
R
VIDEO INPUT
R AUDIO L
L
COMPONENT 2
DVD
/DTV
INPUT
COMPONENT 1
VIDEO
MONITOR
OUTPUT
A/V
INPUT1
(MONO)
RS-232C INPUT
S-VIDEO
(CONTROL/SERVICE)
REMOTE
CONTROL
How to use
1. Select the input source with using the TV/VIDEO button on
the remote control. (If connected to A/V INPUT 1, select
Video 1 input source).
2. Operate the corresponding external equipment. Refer to
external equipment operating guide.
Camcorder
R
AUDIO
Video Game Set
VIDEO
L
Monitor Out Setup
The TV has a special signal output capability which allows you to
hook up a second TV or monitor.
AUDIO INPUT
DVI
COMPONENT1
INPUT OUTPUT INPUT
R
R AUDIO L
COMPONENT 2
DVD
/DTV
INPUT
COMPONENT 1
DIGITAL AUDIO
(OPTICAL)
Connect the second TV or monitor to the TV’s MONITOR OUTPUT.
See the Operating Manual of the second TV or monitor for further
details regarding that device’s input settings.
VIDEO INPUT
L
VIDEO
MONITOR
OUTPUT
A/V
INPUT1
(MONO)
S-VIDEO
RS-232C INPUT
(CONTROL/SERVICE)
NOTE
• Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV, DTV input
sources cannot be used for Monitor out.
S-VIDEO
IN
(R) AUDIO (L)
VIDEO
DVD Setup
How to connect
1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y,
PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to
the AUDIO INPUT jacks on the TV, as shown in the figure.
2. If your DVD only has an S-Video output jack, connect this to the SVIDEO input on the TV and connect the DVD audio outputs to the
AUDIO INPUT jacks on the TV, as shown in the figure.
NOTE: If your DVD player does not have component video output, use
S-Video.
AUDIO INPUT
DVI
COMPONENT1
INPUT OUTPUT INPUT
R
VIDEO INPUT
R AUDIO L
L
COMPONENT 2
DVD
/DTV
INPUT
COMPONENT 1
DIGITAL AUDIO
(OPTICAL)
VIDEO
MONITOR
OUTPUT
A/V
INPUT1
S-VIDEO
RS-232C INPUT
(CONTROL/SERVICE)
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the TV/VIDEO or COMP/RGB/DVI button on the remote control to
select Component 1 or Component 2. (If connected to S-VIDEO,
select the Video 1 or Video 2 external input source.)
3. Refer to the DVD player's manual for operating instructions.
• Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports
on the TV
Y
PB
Video output ports
on DVD player
Y
Y
Y
Y
Pr
Pb
B-Y R-Y
Cr
Cb
PB PR
PR
or
or
DIGITAL AUDIO
OPTICAL
(R) AUDIO (L)
B
S-VIDEO
R
(R) AUDIO (L)
DVD
NOTES
• Digital Audio will not work for Component 2 input source.
• Digital Audio operation has priority if Digital Audio and AUDIO L/R
are connected at the same time.
Owner’s Manual 13
Installation
HDSTB Setup
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital
signals from a digital set-top box or other digital external device, refer to the figure as shown below.
- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) mode.
AUDIO INPUT
Antenna1
Antenna 2
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
R
VIDEO INPUT
R AUDIO L
L
COMPONENT 2
DVI INPUT
DVD
/DTV
INPUT
COMPONENT 1
DIGITAL AUDIO
(OPTICAL)
VIDEO
R
MONITOR
OUTPUT
A/V
INPUT1
(MONO)
RS-232C INPUT REMOTE
S-VIDEO (CONTROL/SERVICE) CONTROL
L
EXTERNAL SPEAKER
AC INPUT
or
or
or
RGB-DTV OUTPUT
(R) AUDIO (L)
(R) AUDIO (L)
DIGITAL AUDIO
OPTICAL
or
DVI-DTV OUTPUT
DIGITAL AUDIO
OPTICAL
(R) AUDIO (L)
B
R
Digital Set-top Box
How to connect
Use the TV’s COMPONENT (Y, PB, PR) INPUT, RGB or DVI jack for
video connections, depending on your set-top box connector. Then,
make the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner’s manual for the
digital set-top box.)
2. Use TV/VIDEO or COMP/RGB/DVI on the remote control to select
Component 1, Component 2, RGB-DTV, or DVI-DTV source.
Signal
480i
480p
720p
1080i
Component 1/2 RGB-DTV,DVI-DTV
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Digital Audio Output
Send the TV’s audio to external audio equipment (stereo system) via
the Digital Audio Output Optical port.
How to connect
1. Connect one end of an optical cable to the TV Digital Audio Optical
Output port.
2. Connect the other end of the optical cable to the digital audio optical
input on the audio equipment.
3. Set the “ TV Speaker option - Off” in the AUDIO menu. Refer to
page 23.
See the external audio equipment instruction manual for operation.
Caution: Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
14 Plasma TV
AUDIO INPUT
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
R
DIGITAL AUDIO
(OPTICAL)
VIDEO INPUT
L
COMPONENT 2
DVI INPUT
COMPONENT 1
DVD
/DTV
INPUT
Installation
PC Setup
- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC)
protocol.
- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. card, change the screen scanning rate for the
graphic card accordingly.
How to connect
1. To get the best picture quality, adjust the PC
graphics card to 1024x768, 60Hz.
2. Use the TV’s RGB INPUT or DVI (Digital Visual
Interface) INPUT port for video connections,
depending on your PC connector.
• If the graphic card on the PC does not output
analog and digital RGB simultaneously, connect
only one of either RGB INPUT or DVI INPUT to
display the PC on the TV.
• If the graphic card on the PC does output analog
and digital RGB simultaneously, set the TV to
either RGB or DVI; (the other mode is set to Plug
and Play automatically by the TV.)
3. Then, make the corresponding audio connections.
If using a sound card, adjust the PC sound as
required.
AUDIO INPUT
Antenna 1
Antenna 2
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
R
VIDEO INPUT
L
COMPONENT 2
DVI INPUT
DIGITAL AUDIO
(OPTICAL)
DVD
/DTV
INPUT
COMPONENT 1
How to use
1. Turn on the PC and the TV.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3. Select RGB-PC or DVI-PC input source in main input option of SETUP menu. (Refer to P.20)
4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another
rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic
card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable.
• Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.
• The synchronization input form for Horizontal and Vertical frequencies is separate.
Monitor Display Specifications (RGB-PC / DVI-PC Mode)
Resolution
640x350
720x400
640x480
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
37.861
85.08
31.469
70.08
37.927
Resolution
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
35.156
56.25
37.879
60.31
48.077
72.18
85.03
46.875
75.00
31.469
59.94
53.674
85.06
37.861
72.80
48.363
60.00
37.500
75.00
56.476
70.06
43.269
85.00
60.023
75.02
800x600
1024x768
Owner’s Manual 15
Installation
Operation
Screen Setup for PC mode
- Be sure to select the RGB-PC/RGB-DTV source before operation.
(For RGB-DTV input source, Position and Reset are available.)
- In DVI-PC and DVI-DTV input source, settings are not adjustable.
- You can manually adjust picture position and minimize image shaking for the PC input source.
Adjustment for screen Position, Clock, and Phase
1. Press the ADJUST button and then use
CLOCK, or PHASE.
2. Press OK button and then use D
ments.
D / E
/E /F /G
button to select POSITION,
buttons to make appropriate adjust-
POSITION
G
CLOCK
D
F
PHASE
• The PHASE adjustment range is -16 ~ +16.
• The CLOCK adjustment range is -30 ~ +30.
G
E
RESET
3. Press OK button.
Adjust Close
Initializing (Reset to original factory values)
- To initialize the adjusted values
1. Press the ADJUST button and then use D
/E
button to select the RESET option.
POSITION
CLOCK
2. Press OK button and then use
3. Press OK button
F /G
button to select Yes.
PHASE
RESET
Adjust Close
16 Plasma TV
G
Initialize Settings
Operation
Turning the TV On
Turning on the TV just after installation
1. Connect power cord correctly.
2. Press the
ON/OFF button on the TV. At this moment, the TV is switched to standby mode.
Press the TV/VIDEO, CH (D / E) button on the TV or press the POWER, TV/VIDEO,
COMP/RGB/DVI, CH (+, -), Number (0 ~ 9) button on the remote control and then the TV will
switch on.
Turning on the TV (power cord is still connected)
1. If the TV was turned off with the
• Press the
ON/OFF button on the TV
ON/OFF button on the TV to turn the TV on.
2. If the TV was turned off with the remote control and then the
ON/OFF button on the TV
• Press the
ON/OFF button on the TV and then press the POWER, TV/VIDEO, COMP/RGB/DVI,
CH (+, -), Number (0 ~ 9) button on the remote control to turn the TV on.
NOTE
• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
On-screen Menus Language Selection
- The menus can be shown on the screen in the selected language. First select your language.
1. Press the MENU button and then use
2. Press the
G
button and then use
D
/
D
E
/
E
button to select the OPTION menu.
button to select Language.
3. Press the G button and then use D / E button to select your desired language.
From this point on, the on-screen menus will be shown in the selected language.
SETUP
Caption
VIDEO
Caption Mode
Caption Option
AUDIO
TIME
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
Aspect Ratio
OPTION
Language
G
English
EZ Demo
Español
ISM Method
Français
White Wash
Low Power
LOCK
MENU
Prev.
Owner’s Manual 17
Operation
Setup Menu Options
EZ Scan (Channel Search)
- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.
- Run EZ Scan again after any Antenna/Cable connection changes.
SETUP
EZ Scan
ANT 1
ANT 2
ANT 1
ANT 2
ANT 1
ANT 2
ANT 1
ANT 2
Ch.Edit
VIDEO
Air
DTV Signal
AUDIO
TIME
OPTION
Cable
Select antenna input,
press
Ch. Label
Main Input
Select antenna input,
press
Cable
Select DTV cable band,
press
Air
Air
Select antenna input,
press
Cable
Select antenna input,
press
Sub Input
Analog/DTV Air
Analog/DTV Air
1. STD
Analog/DTV Air
Analog/DTV Air
Front Display
Analog/DTV Cable
Analog/DTV Cable
2. HRC
Analog/DTV Cable
Analog/DTV Cable
SET ID
Analog+DTV Air(ANT2)
Analog+DTV Air(ANT2)
3. IRC
Analog+DTV Air(ANT2)
Analog+DTV Air(ANT2)
Analog+DTV Cable(ANT2)
Analog+DTV Cable(ANT2)
LOCK
MENU
Prev.
1. Press the MENU button and then use
MENU
D /E
Prev.
Analog+DTV Cable(ANT2)
MENU
Analog+DTV Cable(ANT2)
Prev.
MENU
Prev.
button to select the SETUP menu.
2. Press the G button and then use
D /E
button to select EZ Scan.
3. Press the G button and then use
D /E
button to select antenna input (Based on your connections to antenna 1-2).
• Analog/DTV Air:
Watching the Over-the-air, cable, and digital over-the-air signals via antenna 1 input port
• Analog/DTV Cable:
Watching the Over-the-air, cable, and digital cable signals via antenna 1 input port
• Analog+DTV Air (ANT2):
Watching the Over-the-air, and cable signal via antenna 1 input port and the digital over-the-air signal via antenna 2 input port
• Analog/DTV Cable (ANT2):
Watching the Over-the-air, and cable signa lvia antenna 1 input port and the digital cable signal via antenna 2 input port
* Cable Service Band Note: Select Std=Standard, HRC=HRC Band, or IRC=IRC Band.
(For further band information, contact your cable service provider.)
4. Press the OK button to begin the channel search.
Allow EZ Scan to complete the channel search cycle for TV, CATV, and DTV/CADTV.
Channel Edit
- Create two different types of channel lists in memory: “Custom list” and “Surf"
(Favorite) channel list” from the default channel list created from the EZ Scan
channel search.
- A custom list can be created by toggling each channel on or off with OK button.
Once a channel is highlighted, you will be able to see whether the channel is
currently added or deleted by referring to the small window at the top-left corner
of the screen. You can create your own Surfchannel list with up to 10 channels.
It appears at the bottom-left corner of the screen. Use the SURF button on the
remote control when a channel is highlighted, to add or delete the channel from
the Surf channel list.
- You can create your SURF channel list from the channel list memorized from
EZ Scan.
- CATV is available for 1-125 channel.
1. Press the MENU button and then use
2. Press the G button and then use
D /E
D /E
button to select the SETUP menu.
button to select Ch. Edit.
3. Press the G button. You will now see a screen filled with channel numbers and
a preview picture.
4. Use D / E / F / Gbutton to select a channel and then use the OK button to add
or delete it. Press SURF to add the channel to the Surf List.
5. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
18 Plasma TV
SETUP
EZ Scan
G
Ch.Edit
VIDEO
DTV Signal
Ch. Label
AUDIO
Main Input
Sub Input
TIME
OPTION
LOCK
Front Display
SET ID
MENU
Prev.
Selection ( G or ) leads you
to the channel edit screen.
Operation
DTV Signal Strength
- Reveals how strong your DTV signal is and whether you need to adjust your antenna or digital cable input.
The higher the signal strength, the less likely you are to experience picture degradation.
- Digital DTV Signals: May not be available in all areas, nor are broadcast on all programs.
1. Press the SIGNAL button.
2. View the on-screen signal strength monitor to see the quality of the signal being received.
• You can also check the DTV Signal strength with the SETUP menu.
Channel Label Setup
- Choose preset labels for your channels.
- If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a DTV channel - even if you didn't preset a label for the channel.
SETUP
EZ Scan
Ch.Edit
VIDEO
DTV Signal
Ch. Label
AUDIO
G
Main Input
Selection ( G or ) leads you
to the channel logo screen.
Sub Input
TIME
OPTION
LOCK
Front Display
SET ID
MENU
Prev.
1. Press the MENU button and then use
2. Press the G button and then use
D /E
D /E
button to select the SETUP menu.
button to select Ch.Label.
3. Press the G button. You will now see a screen filled with Labels and a preview screen.
4. Use the CH +/- button to select a channel to Label.
5. Use D / E / F / G button to select the appropriate label for the channel, then press OK button to set the Label to the
selected channel.
6. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
Owner’s Manual 19
Operation
Setup Menu Options continued
Main Picture Source Selection
- Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to
your TV.
1. Press the MENU button and then use
2. Press the G button and then use
D /E
D /E
button to select the SETUP menu.
button to select Main Input.
3. Press the G button and then use D / E button to select the source: DTV, Analog,
Video1, Video2, Component1, Component2, RGB-DTV (or RGB-PC), DVI-DTV
(or DVI-PC).
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
SETUP
VIDEO
EZ Scan
Ch.Edit
DTV
DTV Signal
Analog
Ch. Label
AUDIO
TIME
OPTION
Main Input
Video1
G
Video2
Sub Input
Component1
Front Display
Component2
SET ID
RGB-DTV
DVI-DTV
LOCK
MENU
Prev.
Front LED (Light Emitting Diode) Display
- Illuminates brightly when the set is turned on. The LED displays current TV status.
1. Press the MENU button and then use
D /E
button to select the SETUP menu.
2. Press the G button and then use
D /E
button to select Front Display.
3. Press the G button and then use
Bright.
D /E
button to select Off, Dark, Normal, and
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
SETUP
EZ Scan
Ch.Edit
VIDEO
DTV Signal
Ch. Label
AUDIO
Main Input
Off
Sub Input
TIME
OPTION
Front Display
G
Dark
Normal
SET ID
Bright
LOCK
20 Plasma TV
MENU
Prev.
Operation
V ideo Menu Options
EZ Picture
- EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the
program category.
- When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ
Picture automatically changes to Off.
- Normal, Digital Preset, Night Time, Movie, Weak Signal, Video Game, and Sports settings are preset for optimum picture quality at the factory and are not adjustable.
1. Press the VIDEO button repeatedly to select the picture appearance setup option as shown below:
Off (your own settings), Normal, Digital Preset, Night Time, Movie, Weak Signal, Video Game, and Sports.
• You can also use the VIDEO menu to adjust EZ Picture.
2. Press the EXIT button to save and return to TV viewing.
Manual Picture Control ( Off option)
- Adjust the picture appearance to suit your preference and viewing situations.
SETUP
1. Press the MENU button and then use
D /E
button to select the VIDEO menu.
2. Press the G button and then use D / E button to select the desired picture option
(Contrast, Brightness, Color, Sharpness, or Tint).
3. Press the G button and then use
F / G button
to make appropriate adjustments.
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
VIDEO
AUDIO
EZ Picture
Contrast
85
Brightness
50
Color
50
Sharpness
50
Tint
TIME
OPTION
LOCK
0
G
R
G
Color Temperature
Video Preset
MENU
Prev.
Color Temperature Control
- Choose one of three automatic color adjustments. Set to warm to enhance hotter
colors such as red, or set to cool to see less intense colors with more blue.
SETUP
EZ Picture
Contrast
VIDEO
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
D /E
button to select the VIDEO menu.
button to select Color Temperature .
Brightness
Color
AUDIO
Sharpness
Tint
3. Press the G button and then use D
or Cool.
/E
button to select either Warm, Medium,
TIME
OPTION
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
Color Temperature G
Warm
Video Preset
Medium
Cool
LOCK
MENU
Prev.
V ideo Preset
- Use to quickly reset all the Video menu options to their original factory preset
values.
SETUP
EZ Picture
Contrast
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
D /E
button to select the VIDEO menu.
button to select Video Preset .
VIDEO
Brightness
Color
AUDIO
Sharpness
Tint
3. Press the G button to reset the Video menu options to original values.
TIME
OPTION
LOCK
Color Temperature
Video Preset
MENU
G
Selection ( G or ) presets
the video configuration.
Prev.
Owner’s Manual 21
Operation
Audio Menu Options
Audio Language
- Other languages may be available if a digital signal is provided by the broadcasting station.
SETUP
VIDEO
1. Press the MENU button and then use D
/E
button to select the AUDIO menu.
3. Press the
French.
G
button to select Audio Language.
D /E
D / E
button to select: English, Spanish, or
OPTION
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
English
Spanish
EZ Sound
French
Treble
Bass
TIME
button and then use
G
EZ SoundRite
Balance
AUDIO
2. Press the G button and then use
Audio Language
LOCK
Front Surround
TV Speaker
MENU
Prev.
EZ SoundRite
- Scans for changes in sound level during commercials, then adjusts the sound
to match the specified audio level. SoundRite makes sure that the volume level
remains consistent whether you are watching a commercial or a regular TV
program.
1. Press the MENU button and then use D
2. Press the
G
3. Press the
G
/E
button to select the AUDIO menu.
button and then use
D /E
button to select EZ SoundRite.
button and then use
D /E
button to select On or Off.
SETUP
EZ SoundRite
VIDEO
G
Off
EZ Sound
On
Balance
AUDIO
Treble
Bass
TIME
OPTION
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
Audio Language
LOCK
Front Surround
TV Speaker
MENU
Prev.
EZ Sound
- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound
options based on the program content.
- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Off.
- Normal, Stadium, Theater, and Music are preset for good sound quality at the factory and are not adjustable.
1. Press the SOUND button repeatedly to select the appropriate sound setup as shown below:
Off (your own settings), Normal, Stadium, Theater, and Music.
• You can also adjust EZ Sound in the AUDIO menu.
2. Press EXIT button to save and return to TV viewing.
Manual Sound Control ( Off option)
- Adjust the sound to suit your taste and room situations.
SETUP
1. Press the MENU button and then use D
2. Press the G button and then use D
(Balance, Treble, or Bass).
/E
3. Press the G button and then use F
/G
/E
button to select the AUDIO menu.
EZ SoundRite
VIDEO
button to select the desired sound option
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
TIME
OPTION
LOCK
22 Plasma TV
EZ Sound
Balance
AUDIO
button to make appropriate adjustments.
Audio Language
0
Treble
50
Bass
50
Front Surround
TV Speaker
MENU
Prev.
L
R
G
Operation
Stereo/SAP Broadcasts Setup
- This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if
the station transmits an additional sound signal as well as the original one.
- Stereo or SAP can be received only when the TV station transmits those signals even though you have selected Stereo or
SAP.
- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.
- Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting.
1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono,
Stereo, or SAP appear in turn.
• If other languages available on the digital signal, select them with the SAP button.
2. Press EXIT button to save and return to TV viewing.
Front Surround
-
is a trademark of SRS Labs, Inc.
- TruSurround XT technology is incorporated under license from SRS Labs, Inc.
- Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
1. Press the MENU button and then use D
2. Press the
G
button and then use
D
/E
button to select the AUDIO menu.
/ E button to select Front Surround.
3. Press the G button and then use D / E button to select Off, 3D EchoSound
System or SRS (Sound Retrieval System) TruSurround XT..
• SRS TruSurround XT
Takes advantage of any multi-channel format without needing to add extra
speakers or equipment. Dialog clarity, bass enrichment, and the addition of
stereo audio enhancement that produces an immersive sound experience from
standard stereo material.
SETUP
Audio Language
EZ SoundRite
VIDEO
EZ Sound
Balance
AUDIO
Treble
Bass
TIME
OPTION
Front Surround
G
Off
3D EchoSound System
TV Speaker
SRS TruSurround XT
LOCK
MENU
Prev.
• 3D EchoSound System
Creates a stunning simulated stereo effects from any mono sound and a realistic three-dimensional sound with a very wide and deep sound stage into
stereo sound.
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
TV Speakers On/Off
On/Off Setup
- Turn TV speakers off if using external audio equipment. Feature turns the TV
Speakers option On or Off.
SETUP
EZ SoundRite
VIDEO
1. Press the MENU button and then use D
2. Press the
G
button and then use
D /E
/E
button to select the AUDIO menu.
G
button and then use
D /E
button to select TV Speaker.
Treble
Bass
button to select On or Off.
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
EZ Sound
Balance
AUDIO
TIME
3. Press the
Audio Language
OPTION
Front Surround
TV Speaker
G
Off
On
LOCK
MENU
Prev.
Owner’s Manual 23
Operation
T ime Menu Options
Auto Clock Setup
- The time is set automatically from a digital channel signal.
- The digital channel signal includes information for the current time provided by the broadcasting station.
- Set the clock manually, if the current time is set incorrectly by the auto clock function.
1. Press the MENU button and then use
D /E
button to select the TIME menu.
SETUP
2. Press the
G
button and then use
D /E
button to select Auto Clock.
3. Press the
G
button and then use
D /E
button to select On.
4. Press the G button and then use D / E button to select your viewing area time
zone: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii.
5. Press EXIT button to return to TV viewing or press MENU button to return to
the previous menu.
VIDEO
Auto Clock
G
Off
Manual Clock
On
Off Timer
Time Zone Eastern
On Timer
AUDIO
Sleep Timer
Auto Off
TIME
OPTION
LOCK
MENU
Prev.
Manual Clock Setup
- If current time setting is wrong, reset the clock manually.
SETUP
1. Press the MENU button and then use
D /E
button to select the TIME menu.
Manual Clock
VIDEO
2. Press the
G
button and then use
D /E
button to select Manual Clock.
3. Press the G button and then use F / G button to select either the year, date, or
time option. Once selected, use the D / E button to set the year, date, and time
options.
4. Press EXIT button to return to TV viewing or press MENU button to return to
the previous menu.
Auto Clock
G
Off Timer
Date
On Timer
AUDIO
Year
Time
--
----:
/
--
---
Sleep Timer
Auto Off
TIME
OPTION
LOCK
MENU
Prev.
On/Off
On/Off Timer Setup
-
Timer function operates only if current time has been set.
Off-Timer function overrides On-Timer function if they are set both set to the same time.
The TV must be in standby mode for the On-Timer to work.
If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to
standby mode.
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
D /E
button to select the TIME menu.
button to select Off Timer or On Timer.
3. Press the G button and then use D / E button to select On.
• To cancel On/Off timer function, select Off.
4. Press the
5. Press the
G
G
button and then use
button and then use
6. For only On timer function
Press the G button and then use
Press the G button and then use
D /E
button to set the hour.
D /E
button to set the minutes.
Auto Clock
Manual Clock
VIDEO
Off Timer
On Timer
AUDIO
D /E
D /E
button to select the channel at turn-on.
button to set the sound level at turn-on.
G
Off
Sleep Timer
On
Auto Off
Time 6
: 30 AM
TIME
OPTION
7. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
24 Plasma TV
SETUP
LOCK
MENU
Prev.
Ch.
TV 2-0
Vol
17
Operation
Sleep Timer
- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.
- You can also set up the Sleep Timer in the TIME menu.
1. Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen,
followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to count
down from the number of minutes selected.
3. To check the remaining minutes before the TV turns off, press the TIMER button once.
4. To cancel the Sleep Timer, press the TIMER button repeatedly to select Off.
Auto Off
Off
- If set to on and there is no input signal, the TV turns off automatically after 10
minutes.
1. Press the MENU button and then use D / E button to select the TIME menu.
2. Press the G button and then use D / E button to select Auto Off.
3. Press the G button and then use
D /E
button to select On or Off.
SETUP
Auto Clock
Manual Clock
VIDEO
Off Timer
On Timer
AUDIO
Sleep Timer
Auto Off
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
TIME
G
Off
On
OPTION
LOCK
MENU
Prev.
Owner’s Manual 25
Operation
Option Menu Features
Aspect Ratio Control
- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format.
When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed.
- If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option.
- Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/DVI-DTV (720p/1080i)/DTV(720p/1080i)
input source.
- RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.
- Note: If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and
remain visible.
1. Press the RATIO button repeatedly to select the desired picture format.
You can also adjust Aspect Ratio in the OPTION menu.
• Set By Program
Selects the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9)
• 4:3
Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both
the left and right sides.
• 16:9
Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.
• Horizon
Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both
sides, to create a spectacular view.
• Zoom 1
Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions
of the picture will be cropped.
• Zoom 2
Choose Zoom 2 when you want the picture to be altered, both horizontally extended and vertically cropped. The
picture taking a halfway trade off between alteration and screen coverage.
• Cinema Zoom
Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or
reducing the picture, the image may become distorted.
You can adjust the enlarge proportion of Cinema Zoom using D / E button. The adjustment range is 1~16.
26 Plasma TV
Operation
Caption
1. Use the CC button repeatedly to select Caption Off, EZ Mute, or On.
• EZ Mute shows the selected captions option (if available on program) when the TV sound is muted
. • You can also use the OPTION menu to select Caption.
2. Press EXIT button to save and return to TV viewing.
Caption Mode
Analog Broadcasting System Captions
-
Select a caption mode for displaying captioning information if provided on a program.
Analog caption displays information at any position on the screen usually the program's dialog.
Text displays information, usually at the bottom position and is used for a data service, generally not program related.
Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna 1 source.
This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off.
1. Press the MENU button and then use D / E button to select the OPTION menu.
2. Press the G button and then use D / E button to select Caption Mode.
3. Press the G button and then use D / E button to select caption: CC1, CC2, CC3,
CC4, Text1, Text2, Text3, or Text4.
SETUP
• TEXT
The term for the words that appear in a large black frame and almost cover
the entire screen; usually messages provided by the broadcaster.
CC 1
Caption
VIDEO
AUDIO
• CAPTION
The term for the words that scroll across the bottom of the TV screen; usually
the audio portion of the program provided for the hearing impaired.
Aspect Ratio
TIME
OPTION
LOCK
Caption Mode
G
CC 2
Caption Option
CC 3
Language
CC 4
EZ Demo
Text 1
ISM Method
Text 2
White Wash
Text 3
Low Power
Text 4
MENU
Prev.
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
Digital Broadcasting System Captions
- Choose the language you want the DTV/CADTV Captions to appear in.
- Languages can be chosen for digital sources only if they are included on the program.
1. Press the MENU button and then use D / E button to select the OPTION menu.
2. Press the G button and then use D / E button to select Caption Mode.
SETUP
Aspect Ratio
Caption
3. Press the G button and then use D / E button to select available caption languages: English, Spanish, or French.
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
VIDEO
AUDIO
Caption Mode
G
English
Caption Option
Spanish
Language
French
EZ Demo
TIME
OPTION
ISM Method
White Wash
Low Power
LOCK
MENU
Prev.
Owner’s Manual 27
Operation
Option Menu Features continued
Caption Option
- Customize the DTV/CADTV captions that appear on your screen.
button to select the OPTION
1. Press the MENU button and then use
menu.
D /E
2. Press the G button and then use
D /E
button to select Caption Option.
3. Press the G button and then use
F /G
button to select Custom.
SETUP
VIDEO
4. Use D / E button to customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language.
•
•
•
•
•
•
•
•
Size: Set the size the words will appear in.
Font: Select a typeface for the words.
Text Color: Choose a color for the text.
Text Opacity: Specify the opacity for the text color.
Bg (Background) Color: Select a background color.
Bg (Background) Opacity: Select the opacity for the background color.
Edge Type: Select an edge type.
Edge Color: Select a color for the edges.
Aspect Ratio
Style
Custom
Caption
Size
A Standard
Font
Font 0
Caption Mode
Caption Option
AUDIO
G
Language
Text Opacity
EZ Demo
TIME
White Wash
Low Power
LOCK
MENU
White
Solid
Bg Color
ISM Method
OPTION
Text Color
Black
Bg Opacity
Solid
Edge Type
None
Edge Color
Black
Prev.
5. Press EXIT button to return to TV viewing or press MENU button to return
to the previous menu.
EZ Demo
SETUP
- Shows you how to navigate the TV's on-screen menus.
Caption
VIDEO
1. Press the MENU button and then use D
2. Press the G button and then use
D /E
/E
button to select the OPTION menu.
Aspect Ratio
Caption Mode
Caption Option
AUDIO
button to select EZ Demo.
Language
EZ Demo
TIME
3. Press the G button to start EZ Demo. Press EXIT button to stop EZ Demo.
OPTION
G
ISM Method
Selection ( G or
leads you to the
EZ Demo.
White Wash
Low Power
LOCK
MENU
Prev.
ISM (Image Sticking Minimization) Method
- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost
image remaining; even when you change the image. Avoid allowing any fixed image to remain on the TV's screen
for a long period of time.
1. Press the MENU button and then use D
2. Press the
G
button and then use
D
3. Press the G button and then use D
or Inversion.
/E
button to select the OPTION menu.
/ E button to select ISM Method.
/E
button to select either Normal, Orbiter,
SETUP
Caption
VIDEO
4. Press EXIT button to return to TV viewing or press MENU button to return to
the previous menu.
28 Plasma TV
Caption Mode
Caption Option
AUDIO
• Normal
If image sticking is never a problem, ISM is not necessary - set to Normal.
• Orbiter
Orbiter may help prevent ghost images. However, it is best not to allow any
fixed image to remain on the screen. To avoid a permanent image on the
screen, the image will move once per minute: Right → Right → Downside →
Downside → Left → Left → Upside → Upside.
• Inversion
Inversion will automatically invert the plasma display panel color every 30 minutes.
Aspect Ratio
Language
EZ Demo
TIME
OPTION
LOCK
ISM Method
G
Normal
White Wash
Orbiter
Low Power
Inversion
MENU
Prev.
)
Operation
White Wash
Wash
- White Wash removes permanent images from the screen.
- Set White Wash ‘ON’ until fixed image disappears.
- Note: An excessive permanent image may be impossible to clear entirely with
White Wash.
Aspect Ratio
SETUP
Caption
VIDEO
Caption Mode
Caption Option
AUDIO
1. Press the MENU button and then use D
2. Press the G button and then use
D /E
/E
Language
button to select the OPTION menu.
button to select White wash.
3. Press the G button and then use D / E button to select On or Off.
• When you select On, the screen changes to white.
EZ Demo
TIME
ISM Method
White Wash
OPTION
G
LOCK
MENU
Off
On
Low Power
Prev.
4. To return to normal viewing, press the any button.
Low Power
- Low power reduces the plasma display's power consumption.
1. Press the MENU button and then use D
/E
button to select the OPTION menu.
2. Press the
G
button and then use
D /E
button to select Low power.
3. Press the
G
button and then use
D /E
button to select On or Off.
Aspect Ratio
SETUP
Caption
VIDEO
Caption Mode
Caption Option
AUDIO
Language
EZ Demo
• If you select On, the screen darkens.
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
TIME
ISM Method
White Wash
OPTION
Low Power
LOCK
MENU
Prev.
G
Off
On
Split Zoom (DTV 720p, or 1080i mode only)
- Enlarges the picture with correct proportions.
- When enlarging the picture, the image may become distorted.
1. Press the ZOOM button in DTV 720p, or 1080i modes.
F
D /E /F /G
buttons to select the screen split zoom section.
F
2. Use the
F
F
3. To return to normal viewing, press the ZOOM button again.
Owner’s Manual 29
Operation
Lock Menu Options
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station.
The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories
chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be
done :
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enablethe lock
V-Chip rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV
Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating
System (MPAA) only.
Ratings for Movies previously shown in theaters:
Movie Ratings :
• Blocking Off
(Permits all programs)
•G
(General audience)
• PG
(Parental guidance suggested)
• PG-13
(Parents strongly cautioned)
•R
(Restricted)
• NC-17
(No one 17 and under admitted)
•X
(Adult only)
If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.
Ratings for Television programs including made-for-TV movies :
• TV-G
• TV-PG
• TV-14
• TV-MA
• TV-Y
• TV-Y7
(General audience)
(Parental guidance suggested)
(Parents strongly cautioned)
(Mature audience only)
(All children)
(Children 7 years older)
TV Rating Children:
• Age
• Fantasy Violence
(applies to TV-Y, TV-Y7)
(applies to TV-Y7)
TV Rating General:
• Age
• Dialogue - sexual dialogue
• Language - adult language
• Sex - sexual situations
• Violence
(applies
(applies
(applies
(applies
(applies
Aux. Block
• Video 1, 2
• Component 1, 2
• RGB, DVI
30 Plasma TV
(On, Off)
(On, Off)
(On, Off)
to TV-G, TV-PG, TV-14, TV-MA)
to TV-PG, TV-14)
to TV-PG, TV-14, TV-MA)
to TV-PG, TV-14, TV-MA)
to TV-PG, TV-14, TV-MA)
Operation
Parental Lock Setup
- Lets you set up blocking schemes to block specific channels, ratings, and external viewing sources.
- A password is required to gain access to this menu if the Lock System is turned on
1. Press the MENU button and then use D
Then, press the G button
/E
button to select the LOCK menu.
SETUP
Lock System
Set Password
• If Lock is already set, enter the password as requested.
• The TV is set up with the initial password “7-7-7-7”.
VIDEO
• Lock System: Activates or disables the blocking scheme you set up previously.
• Set Password: Change the password by inputting a new password twice.
• Movie Rating (MPPA): Blocks movies according to the movie ratings limits
specified, so children cannot view certain movies. You can set the ratings
limit by blocking out all the movies with the ratings above a specified level.
Keep in mind that the movie ratings limit only applies to movies shown on
TV, not TV programs, such as soap operas.
• TV Rating-Children: Prevents children from watching certain children's TV
programs, according to the ratings limit set. The children rating does not
apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can
view those programs.
• TV Rating-General: Based on the ratings, blocks certain TV programs that
you and your family do not want to view.
• Aux. Block: Enables you to select a source to block from the external
source devices you have hooked up.
Off
On
Block Ch.
Movie Rating
AUDIO
2. Use the D / E button to choose from the following Lock Menu options. Once the
option is selected, change the settings to your preference.
G
TV Rating-Children
TV Rating-General
TIME
Aux. Block
OPTION
LOCK
MENU
Prev.
3. Press EXIT button to return to TV viewing or press MENU button to return to
the previous menu.
Note
• If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control.
Owner’s Manual 31
Operation
PIP (Picture-In-Picture) / POP / Twin Picture
- PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other
source will show a smaller inset image.
- Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each
source is given half the screen.
- If you set the block/rating for Lock menu options in PIP/Twin Picture mode, “Rating Blocked” doesn’t display on screen.
Watching PIP/POP/Twin
PIP/POP/Twin Picture
Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below.
PIP Mode
POP Mode
Twin Picture Mode
F
D
E
TV 2-0
TV 4-0
TV 6-0
PIP Off
Selecting an Input Signal Source for PIP/Twin
PIP/Twin Picture
Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes
the PIP source. You can also select sources for the Sub Input in the SETUP menu.
Main Picture Source
DTV Signal
Analog Signal
Available Sub Picture Sources
Analog, Video 1, and Video 2
DTV, Analog, Video 1, and Video 2
Swapping the PIP/T
win Picture
PIP/Twin
Use the SWAP button to switch the main and sub pictures.
• Component 1, Component 2, RGB-PC (or RGB-DTV), DVI-DTV (or DVI-PC) input sources for the main picture can’t
be used to swap the main and sub pictures.
Main Picture
Sub Picture
Main Picture
Sub Picture
TV Program selection for PIP
1. Press the PIP button.
2. Select the Analog or DTV option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+
PIPCH- button to select a channel for the sub picture.
32 Plasma TV
/
Operation
Moving the PIP sub picture
In PIP mode, press the
screen.
D /E /F /G
button to move the sub picture to a different location on the
Adjusting Main and Sub Picture Sizes for Twin Picture
Use the
i.e)
D /E /F /G
button to change main and sub picture sizes in Twin Picture mode.
If the maximal adjusted
screen is 16:9, the large
screen appears the gray
part at both the up and
down sides.
If the maximal adjusted
screen is 4:3, the large
screen is filled with entire
screen vertically as shown.
POP (Picture-out-of-Picture: Channel Scan)
- Use POP to search the programs of all the memorized channels one-by-one on the 3 PIP screen display,
(while the main picture source remains the current channel). The pictures of all the programmed channels
are searched with the 3 POP screen.
- Note: Run EZ Scan channel search before using POP mode.
1. Press the PIP button to activate the POP mode while in PIP mode.
• Channel selection: Use F button to enlarge the selected channel being searched on the PIP
screen to shift it for viewing on the Main screen.
• PIP selection: Use D / E button to select one of 3 PIP screen pictures in POP mode.
• Input source selection for PIP: Use PIP INPUT button or Sub Input option on the SETUP
menu to select an input source for the sub picture (You can’t select DTV for main and sub picture simultaneously). You can only select the Analog and DTV signal for sub input source in
POP mode.
F
D
E
TV 2-0
TV 4-0
TV 6-0
2. Press the EXIT button to cancel POP mode.
Owner’s Manual 33
External Control Device Setup
External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the Monitor’s functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
- RS-232C connection cables are not supplied with the Monitor.
RS-232C Setup
VIDEO INPUT
AUDIO INPUT
Antenna 1
Antenna 2
DVI
COMPONENT1
INPUT OUTPUT INPUT
RGB INPUT
AUDIO INPUT
R
R AUDIO L
L
COMPONENT 2
DVD
/DTV
INPUT
DVI INPUT
COMPONENT 1
DIGITAL AUDIO
(OPTICAL)
VIDEO
R
MONITOR
OUTPUT
A/V
INPUT1
(MONO)
RS-232C INPUT REMOTE
S-VIDEO (CONTROL/SERVICE) CONTROL
L
EXTERNAL SPEAKER
AC INPUT
PC
Type of Connector; D-Sub 9-Pin Male
No.
1
2
3
4
5
6
7
8
9
1
Pin Name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
5
9
6
RS-232C Configurations
3-Wire Configurations
(Not standard)
7-Wire Configurations
(Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
34 Plasma TV
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
4
6
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
External Control Device Setup
Set ID
Use this function to specify a monitor ID number.
Refer to ‘Real Data Mapping’. See page 36.
SETUP
EZ Scan
Ch.Edit
1. Press the MENU button and then use
D /E
button to select the SETUP menu.
2. Press the G button and then use
button to select SET ID.
VIDEO
DTV Signal
Ch. Label
D /E
AUDIO
3. Press the G button and then use D / E button to adjust SET ID to choose the
desired monitor ID number. The adjustment range of SET ID is 1 ~ 99.
4. Press EXIT button to return to TV viewing or press MENU button to return to the
previous menu.
Main Input
Sub Input
TIME
OPTION
LOCK
Front Display
G
SET ID
MENU
1
Prev.
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code
* Use a crossed (reverse) cable.
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
Command Reference List
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control Lock Mode
14. PIP/Twin
15. PIP Position
16. Treble
17. Bass
18. Balance
19. Color Temperature
20. PIP Input Source
21. Orbiter
22. White Wash
23. Orbiter Time Setting
24. Orbiter Pixel Setting
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
j
a
b
c
d
e
f
g
h
i
j
k
l
m
n
q
r
s
t
u
y
p
q
r
s
0~1
0~9
0 ~ 15
0~1
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~1
0~1
0~3
0~3
0 ~ 64
0 ~ 64
0 ~ 64
0~2
0~3
0~2
0~1
1 ~ 64
0 ~A
* [Command 1]: First command to control the set. (j or k)
* [Command 2]: Second command to control the set.
* [Set ID]: You can adjust the set ID to choose desired monitor
ID number in Setup menu. Adjustment range is 1
~ 99. When selecting Set ID ‘0’, every connected
the TV is controlled. Set ID is indicated as decimal
(1~99) on menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit ‘FF’ data to read status of command.
* [Cr]: Carriage Return
ASCII code ‘0x0D’
* [ ]: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from non-viable
functions or communication errors.
Data 1: Illegal Code
2: Not supported function
3: Wait more time
COMCOMDATA 0
DATA 1
DATA 2
DATA 3
MAND 1 MAND 2 (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal)
25. Channel Tuning
26. Channel Add/Del
27. Key
m
m
m
a
b
c
01 ~ 87
00 ~ 01
01 ~ 87
00 ~ FE 00 ~ 15
Owner’s Manual 35
External Control Device Setup
01. Power (Command2:a)
05. Volume Mute (Command2:e)
G To control Power On/Off of the Monitor.
G To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
1 : Power On
Acknowledgement
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute off (Volume on)
1 : Volume mute on (Volume off)
[a][ ][Set ID][ ][OK][Data][x]
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback
presents status about each function.
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
06. Volume Control (Command2:f)
02. Input Select (Command2:b) (Main Picture Input)
G To select input source for the Monitor.
Transmission
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 0: DTV
1: Analog
2: Video 1
3: Video 2
4: Component 1
G To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
[k][f][ ][Set ID][ ][Data][Cr]
5:
6:
7:
8:
9:
Component 2
RGB-DTV
RGB-PC
DVI-DTV
DVI-PC
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping’ as shown below.
Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
Acknowledgement
07. Contrast (Command2:g)
[b][ ][Set ID][ ][OK][Data][x]
G To adjust screen contrast.
You can also adjust contrast in the Video menu.
03. Aspect Ratio (Command2:c) (Main picture format)
Transmission
G To adjust the screen format.
You can also adjust the screen format using the RATIO
button on remote control or in the Option menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
[k][c][ ][Set ID][ ][Data][Cr]
Data 0: Auto (Set by program)
1: Normal screen (4:3)
2: Wide screen (16:9)
3: Horizon
4: Zoom 1
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping’ as shown below.
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
5: Zoom 2
6: Cinema Zoom (1)
15: Cinema Zoom (16)
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
04. Screen Mute (Command2:d)
08. Brightness (Command2:h)
G To adjust screen brightness.
You can also adjust brightness in the Video menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping’ as shown below.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
G To select screen mute on/off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
* Real data mapping
0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
64 : Step 100
36 Plasma TV
External Control Device Setup
09. Color (Command2:i)
14. PIP / POP / Twin Picture (Command2:n)
G To adjust the screen color.
You can also adjust color in the Video menu.
G To control the PIP (Picture-in-Picture)/POP/Twin picture.
You can also control the PIP/POP/Twin picture using the
PIP button on the remote control.
Transmission
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
[k][n][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping’. See page 36.
Acknowledgement
Data 0: PIP off
1: PIP
[i][ ][Set ID][ ][OK][Data][x]
Acknowledgement
2: POP
3: Twin Picture
[n][ ][Set ID][ ][OK][Data][x]
10. Tint (Command2:j)
G To adjust the screen tint.
You can also adjust tint in the Video menu.
15. PIP Position (Command2:q)
G To select sub picture position for PIP.
Transmission
Transmission
[k][q][ ][Set ID][ ][Data][Cr]
[k][j][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0:
1:
2:
3:
[j][ ][Set ID][ ][OK][Data][x]
Acknowledgement
Data Red : 0 ~ Green : 64
• Refer to ‘Real data mapping’. See page 36.
Right down on screen
Right up on screen
Left up on screen
Left down on screen
[q][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command2:k)
G To adjust the screen sharpness.
You can also adjust sharpness in the Video menu.
Transmission
16. Treble (Command2:r)
G To adjust treble.
You can also adjust treble in the Audio menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping’. See page 36.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
[k][r][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping’. See page 36.
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command2:l)
G To select OSD (On Screen Display) on/off.
17. Bass (Command2:s)
Transmission
G To adjust bass.
You can also adjust bass in the Audio menu.
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off
1: OSD on
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping’. See page 36.
Acknowledgement
13. Remote Control Lock Mode (Command2:m)
[s][ ][Set ID][ ][OK][Data][x]
G To lock the remote control and the front panel controls on
the set.
18. Balance (Command2:t)
G To adjust balance.
You can also adjust balance in the Audio menu.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off
1: Lock on
Transmission
Acknowledgement
[k][t][ ][Set ID][ ][Data][Cr]
[m][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping’. See page 36.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 37
External Control Device Setup
19. Color Temperature (Command2:u)
24. Orbiter Pixel Setting (Command2:s)
G To adjust color temperature.
You can also adjust color temperature in the Video
menu.
G To adjust pixel number in orbiter function.
Transmission
[j][s][ ][Set ID][ ][Data][Cr]
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: A
Data 0: Warm
Acknowledgement
1: Medium 2: Cool
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
[u][ ][Set ID][ ][OK][Data][x]
25. Channel Tuning (Command: m a)
20. PIP Input Select (Command2:y)
G To tune channel to following physical/major/minor number
G To select input source for sub picture in PIP/Twin picture mode.
Transmission
Transmission
Data 0: Physical channel number (Transmit by Hexadecimal code)
* NTSC air: 02 ~ 45
NTSC cable: 01, 0E ~ 7D
ATSC air: 01 ~ 45
ATSC cable: 01 ~ 87
1: Major channel number (Transmit by Hexadecimal code)
* NTSC air: 02 ~ 45, NTSC cable: 01 ~ 7D
ATSC air: 01 ~ 63, ATSC cable: 01 ~ 87
2: Minor channel number (Transmit by Hexadecimal code)
* NTSC air: 00 (must be 0), ATSC: 01 ~ FE
3: High nibble → Main picture: 0, Sub picture (PIP): 1
Low nibble → NTSC air: 0, NTSC cable: 1, ATSC: 2,
Example) If you want PIP channel tuned to ATSC cable (standard) 30-5, the command sequence is ma 00 1e 1e 05 12.
[k][y][ ][Set ID][ ][Data][Cr]
Data 0: DTV
1: Analog
2: Video 1
3: Video 2
Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
21. ISM Method (Command2:p)
G To avoid having a fixed image remain on screen.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0: Normal
1: Orbiter
2: Inversion
Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][Cr]
* To change the channel between ATSC air and ATSC cable,
change the antenna setting with EZ Scan.
Acknowledgement
[a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][x]
[a][ ][Set ID][ ][NG][Data0][x]
26. Channel Add/Del (Command: m b)
22. White Wash (Command2:q)
G To add and delete the channels
G To control the white wash function on/off.
You can also adjust white wash in Option menu.
Transmission
Transmission
Data 0: Channel Delete
1: Channe Add
[j][q][ ][Set ID][ ][Data][Cr]
Data 0: White Wash off
1: White Wash on
Acknowledgement
[m][b][ ][Set ID][ ][Data][Cr]
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
[b][ ][Set ID][ ][NG][Data][x]
[q][ ][Set ID][ ][OK][Data][x]
27. Key (Command: m c)
23. Orbiter Time Setting (Command2:r)
G To adjust orbiter operation time term.
Transmission
[j][r][ ][Set ID][ ][Data][Cr]
G To send IR remote key code
Transmission
[m][c][ ][Set ID][ ][Data][ ][Cr]
Data Key code: Refer to page 40.
Data Min: 1 ~ Max: 64
Acknowledgement
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
[r][ ][Set ID][ ][OK][Data][x]
* It’s impossible to command the IR Code 0x08 and 0xC4
with RS-232C.
38 Plasma TV
IR Codes
IR Codes
How to Connect
G Connect your wired remote control to the Remote Control port on the TV.
Remote Control IR Codes
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
TC
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
G Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
G Lead code
9 ms
4.5 ms
0.55 ms
G Repeat code
9 ms
2.25 ms
G Bit description
• Bit “0”
• Bit “1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
G Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
Owner’s Manual 39
IR Codes
Code (Hexa)
0x0B
0x08
0xC4
0xC5
0x98
0x79
0x0E
0x10 ~ 0x19
0x4C
0x1A
0x09
0x02
0x03
0x00
0x01
0x1E
0xAA
0x39
0x40
0x41
0x07
0x06
0x44
0x43
0x52
0x4D
0x5B
0x60
0x72
0x71
0x61
0x63
0x65
0x7B
0x0A
0xCB
0xD6
0x5A
0xD0
0xBF
0xD4
0xD5
0xD7
0xC6
0x76
0x77
0xAF
0x70
0x96
40 Plasma TV
Function
TV/VIDEO
MODE
POWER
POWER ON
POWER OFF
COMP/RGB/DVI
RATIO
TIMER
Number Key 0~ 9
- (Dash)
FLASHBK
MUTE
VOL +
VOL CH +
CH SURF
INFO
CC
D
E
F
G
OK
MENU
SOUND
VIDEO
EXIT
PIP
PIPCH PIPCH +
PIP INPUT
SWAP
FREEZE
ZOOM
SAP
ADJUST
TV
VIDEO 1
VIDEO 2
COMPONENT 1
COMPONENT 2
RGB-PC
RGB-DTV
DVI-DTV
Ratio 4:3
Ratio 16:9
Ratio Zoom
MULTI PIP
SIGNAL
Note
R/C Button
R/C Button
R/C Button (Power On/Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (TV Input Selection)
Discrete IR Code (Video1 Input Selection)
Discrete IR Code (Video2 Input Selection)
Discrete IR Code (Component1 Input Selection)
Discrete IR Code (Component2 Input Selection)
Discrete IR Code (RGB-PC Input Selection)
Discrete IR Code (RGB-DTV Input Selection)
Discrete IR Code (DVI-DTV Input Selection)
Discrete IR Code (Only 4:3 Mode)
Discrete IR Code (Only 16:9 Mode)
Discrete IR Code (Only Zoom Mode)
Channel Search
R/C Button
Programming the Remote
Programming the Remote
G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable
devices of other manufacturers.
Note that the remote control may not control all models of other brands.
Programming a code into a remote mode
1. Test your remote control.
To find out whether your remote control can operate the component without programming, turn on the component such as a VCR
and press the corresponding MODE button (VCR) on the remote control, while pointing at the component. Test the POWER and
CH +/- buttons to see if the component responds properly. If not, the remote requires programming to operate the device.
2. Turn on the component to be programmed, then press the corresponding MODE button on the remote control.
3. Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed for the code.
4. There are two ways to find the right code for the component.
A. If you press the CH +/- buttons repeatedly, the codes will change one at-a-time. Press the POWER button after each code
change. If the right code is found, the device will turn off.
B. Enter a code number using the number buttons on the remote. Programming code numbers for the corresponding component
can be found on the following pages. Again, if the code is correct, the device will turn off.
5. Press the MENU button to store the code.
6. Test the remote control functions to see if the component responds properly. If not, repeat from step 2.
Owner’s Manual 41
Programming Codes
Programming Codes
VCRs
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
AIWA
AKAI
034
016
125
072
031
012
035
028
108
003
031
005
065
112
108
012
034
059
006
029
036
129
003
034
031
107
132
012
004
043
031
031
012
040
043
012
048
130
KENWOOD
014
047
001
101
034
003
017
040
031
067
012
069
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
013
063
031
031
067
101
013
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
108
072
011
033
013
040
107
145
003
031
053
058
148
014
032
105
113
125
022
003
102
017
131
003
013
031
101
031
024
003
056
077
034
013
031
067
034
010
TATUNG
TEAC
TECHNICS
TEKNIKA
039
034
031
019
101
034
006
008
059
040
040
012
048
012
040
003
031
053
012
034
058
AMPRO
ANAM
AUDIO DYNAMICS
BROKSONIC
CANON
CAPEHART
CRAIG
CURTIS MATHES
DAEWOO
DAYTRON
DBX
DYNATECH
ELECTROHOME
EMERSON
FISHER
FUNAI
GE
GO VIDEO
HARMAN KARDON
HITACHI
INSTANTREPLAY
JCL
JCPENNY
JENSEN
JVC
043 046 124
146
033
023
037
031
040
033
007
108
116
103
039 043
129
033
135
041
010 064
110 111
117 119
023 039 043
053
027
035
101
153
010
LG (GOLDSTAR)
LLOYD
LXI
MAGIN
MAGNAVOX
MARANTZ
MARTA
MATSUI
MEI
MEMOREX
017
031
037
131
008
025
034
046
138
009
033
109
136
045
018
063
033
033
013
066
063 072
144 147
MTC
MULTITECH
NEC
026 034
137 150
NORDMENDE
OPTONICA
PANASONIC
MGA
MINOLTA
MITSUBISHI
PENTAX
015 033
101
031 033 043
050 055 060
150 152
PHILCO
PHILIPS
PILOT
PIONEER
034 039 043
048
012 013 020
106 114 123
009 013 014
034 101 106
033 034 041
068
031 033 067
030
033
010
034
102
046
020
020
051
REALISTIC
RICO
RUNCO
SALORA
SAMSUNG
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
SANSUI
SANYO
SCOTT
SEARS
010
SHARP
SHINTOM
SONY
SOUNDESIGN
STS
SYLVANIA
SYMPHONIC
TANDY
014
066
020
041
109
147
008
033
054
075
033
062
140
145
034
063
144
010 014
034 040
101
THOMAS
TMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
00 009
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
CATV
CATV
Brand
Codes
Brand
Codes
ABC
003
046
112
014
005
026
092
007
007
065
080
019
023
020
057
032
072
008
052
GOLDEN CHANNEL
HAMLIN
HITACHI
HOSPITALITY
JERROLD
030
049
052
070
002
009
074
001
037
033
010
100
028
015
073
016
044
100
006
AJIN
ANTRONIK
ARCHER
CABLE STAR
CENTURION
CENTURY
CITIZEN
COLOUR VOICE
COMBANO
COMTRONICS
DIAMOND
EAGLE
EASTERN
ELECTRICORD
GE
GEMINI
GI
42 Plasma TV
004 039 042
052 053
007 014 024
090
081
030
030 040
062 066
022 025 054
074
LG (GOLDSTAR)
M-NET
MACOM
MAGNAVOX
MEMOREX
MOVIE TIME
NSC
OAK
PANASONIC
PARAGON
PHILIPS
050 055
055
077
003 004 008
010 052 069
106 101 005
012 064 079
032
028 038 071
Brand
PIONEER
POST NEWS WEEK
PRUCER
PTS
PULSAR
RCA
REGAL
REGENCY
REMBRANT
RK
SAMSUNG
SCIENTIFIC ATLANTA
031 037 053
047
012 013 020
SHERITECH
SIGNAL
SIGNATURE
Codes
Brand
Codes
065
034
076
016
059
011
073
100
047
049
057
025
091
102
003
043
022
030
052
SL MARX
SPRUCER
STARCOM
STARGATE
SYLVANIA
TADIRAN
TAEKWANG
TAIHAN
TANDY
TEXSCAN
TOCOM
TOSHIBA
UNIKA
UNITED CABLE
UNIVERSAL
030
047
002
008
067
030
110
105
017
029
039
100
007
004
005
026
012
087
100
085 090
051 052 063
048 071 072
074
050
107 030 068
011 041 042
045 046
VIEWSTAR
ZENITH
078
004 008 009
030
067
040 056
014
053
007
027
015
088
114
024
014
032
018
089
060
024
035
086
093
Programming Codes
HDSTB
Brand
Codes
Brand
ALPHASTAR DSR
AMPLICA
BIRDVIEW
BSR
CAPETRONICS
CHANNEL MASTER
123
050
051
053
053
013
036
008
054
050
005
011
141
024
038
093
097
122
089
EUROPLUS
FUJITSU
CHAPARRAL
CITOH
CURTIS MATHES
DRAKE
DX ANTENNA
ECHOSTAR
ELECTRO HOME
126 129
014 015 018
055
009 012 077
145
006 007 010
052 112 116
046
040
094
098
056
057
095
099
076
058
096
100
Codes
114
017
133
GENERAL INSTRUMENT 003
031
HITACHI
139
033
HOUSTON TRACKER
057
HUGHES
068
HYTEK
053
JANIEL
060
JERROLD
061
KATHREIN
108
LEGEND
057
LG
001
LUTRON
132
LUXOR
062
MACOM
010
065
021
134
004
059
140
037
104
Brand
022 027
016 029
101
039 051
147
144
059 063 064
Codes
MEMOREX
NEXTWAVE
NORSAT
057
028
069
PACE SKY SATELLITE 143
PANASONIC
060
PANSAT
121
PERSONAL CABLE 117
PHILIPS
071
PICO
105
PRESIDENT
019
PRIMESTAR
030
PROSAT
072
RCA
066
REALISTIC
043
SAMSUNG
123
SATELLITE SERVICE CO 028
085
SCIENTIFIC ATLANTA
032
SONY
103
124 125
070
Brand
Codes
STARCAST
SUPER GUIDE
TEECOM
041
020
023
088
137
002
016
044
078
101
135
115
128
081
091
142
TOSHIBA
UNIDEN
102
110 111
UNIDEN
VIEWSTAR
WINEGARD
ZENITH
106
074
124 125
026 075 087
090 107 130
127
025 042 043
045 048 049
079 080 086
136
146
082 083 084
120
035 047 057
138
Audio
Brand
AIWA
Codes
014
125
230
AKAI
163
ANAM
003
059
217
BURMECTER
252
CARVER
086
CLARION
199
DAEWOO
027
102
DENON
015
FANTASIA
071
FINEARTS
022
FISHER
089
LG(GOLDSTAR)
001
087
190
211
HAITAI
034
HARMAN/KARDON 068
INKEL
037
078
122
152
157
189
225
247
028 070 096
129 139 229
014 017 023
106 189 216
235 236
Brand
Codes
JVC
KEC
KENWOOD
004
185
038
170
215
030
045
014
100
175
179
201
214
238
103
111
002
034
097
049
104
107
046
013
048
133
158
007
142
104
KOHEL
NAD
LOTTE
053 060 084
148 198 221
075 130 143
099
021
107
191
212
035
058
079
149
153
158
207
226
024
108
192
239
188
062
095
150
154
159
222
227
029
110
210
222
069
121
151
155
160
224
243
LXI
MAGNAVOX
MARANTZ
MCINTOSH
MCS
MEMOREX
NAD
ONKYO
OPTIMUS
PANASONIC
PENNEY
013
186
050
171
222
046
016
172
176
180
202
219
240
141
187
067 089
197 206
036
173
177
181
208
223
098
174
178
183
213
232
018 020 025
041 081 090
112
Brand
Codes
PHILIPS
PIONEER
026
039
065
115
113
080
092
103
124
193
204
011
019
106
031
072
156
206
005
044
118
012
076
162
166
205
254
010
185
101
QUASAR
RCA
RCX
REALISTIC
SAMSUNG
SANSUI
SANYO
SCOTT
SHARP
SHERWOOD
SONY
TAEKWANG
040 041 047
056 057 132
140
033 064 113
220 241 251
TEAC
TECHNICS
112
042
091
123
106
145
194
244
135
083
186
032
082
184
209
006
045
126
020
077
163
167
231
143
043
093
127
253
063
094
250
146
195
245
138
234
182
203
246
144
Brand
Codes
TOSHIBA
THE
VICTOR
WARDS
YAMAHA
147 218
137
061
088 131
089
054 055 066 092
199
051 052
117 119
199 200
158
109
248
073
105
164
168
233
114
249
074
161
165
169
242
085 106 136
187 237
113 128 134
DVD
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
DENON
GE
HARMAN KARDON
JVC
LG
022
020 014
005 006
027
012
001 010 016 025
MAGNAVOX
MARANTZ
MITSUBISHI
NAD
ONKYO
PANASONIC
013
024
002
023
008 017
003 009
PHILIPS
PIONEER
PROCEED
PROSCAN
RCA
SAMSUNG
013
004
021
005
005
011
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
007
005
019
009
010
026
006
006
015
006
008
018
016 025
Owner’s Manual 43
Troubleshooting Checklist
Troubleshooting Checklist
• Check whether the TV is turned on.
No picture &
No sound
• Is the power cord inserted into wall power outlet?
• Test the wall power outlet, plug another product’s power cord into the outlet
where the TV’s power cord was plugged in.
Picture OK &
No sound
• Press the VOLUME (G) button.
• Sound muted? Press MUTE button.
• Check to see if there is any object between the TV and the remote control
causing obstruction.
The remote control
doesn’t work
• Are batteries installed with correct polarity (+ to +, - to -)?
(Refer to p.9)
• Correct remote operating mode set: TV, VCR etc.?
• Install new batteries. (Refer to p.9)
Picture appears slowly
after switching on
• This is normal, the image is muted during the TV startup process. Please
contact your service center, if the picture has not appeared after five minutes.
• Select Color in the Video menu and press the VOLUME (G) button.
(Refer to p.21)
No or poor color
or poor picture
• Keep a sufficient distance between the TV and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.)
Horizontal/vertical bars
or picture shaking
• Check for local interference such as an electrical appliance or power tool.
No output from one of
the speakers
• Adjust Balance in the AUDIO menu. (Refer to p.22)
Unusual sound from
inside the TV
• A change in ambient humidity or temperature may result in an unusual noise
when the plasma display is turned on or off and does not indicate a fault with
the TV.
44 Plasma TV
Maintenance
Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your
new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and
a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the
screen.
2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.
Extended Absence
If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.
Owner’s Manual 45
Product Specification
Product Specifications
MODELS
DU-42PZ60/42PZ60A
DU-42PZ70/42PZ70A
DU-50PZ60/50PZ60A
DU-50PZ70/50PZ70A
/42PZ60B/42PZ60C
/42PZ70B/42PZ70C
/50PZ60B/50PZ60C
/50PZ70B/50PZ70C
/42PZ60K/42PZ60R
/42PZ70K/42PZ70R
/50PZ60K/50PZ60R
/50PZ70K/50PZ70R
/42PZ60S
/42PZ70S
/50PZ60S
/50PZ70S
DU-42PZ60H/42PZ60HA DU-42PZ70H/42PZ70HA DU-50PZ60H/50PZ60HA DU-50PZ70H/50PZ70HA
/42PZ60HB/42PZ60HC
/42PZ70HB/42PZ70HC
/50PZ60HB/50PZ60HC
/50PZ70HB/50PZ70HC
/42PZ60HK/42PZ60HR
/42PZ70HK/42PZ70HR
/50PZ60HK/50PZ60HR
/50PZ70HK/50PZ70HR
/42PZ60HS
/42PZ70HS
/50PZ60HS
/50PZ70HS
Width (inches / mm)
41 / 1040
41 / 1040
48.2 / 1225
48.3 / 1226.2
Height (inches / mm)
27.5 / 699.5
26.4 / 669.5
30.6 / 778
30.6 / 778
Depth (inches / mm)
3.7 / 95
3.7 / 95
3.85 / 98
3.9 / 99
Weight (pounds / kg)
76.1 / 34.5
73.4 / 33.3
101.2 / 45.9
98.1 / 44.5
Power requirement
AC100-240V ~ 50/60Hz
Television System
NTSC-M, ATSC
Program Coverage
VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125, CADTV 1 ~ 135. DTV 2 ~ 69
External Antenna Impedance
75 Ω
Resolution
1024 x 768 (Dot)
1366 x 768 (Dot)
Color
16,770,000 (256 steps of each R, G and B)
Operating Temperature Range
32 ~ 104°F (0 ~ 40°C)
Operating Humidity Range
Less than 80%
Maximum Elevation
6561 feet (2000m)
• The specifications shown above may be changed without prior notice for quality improvement.
46 Plasma TV
LG ELECTRONICS, INC.
PLASMA TV — U.S. LIMITED WARRANTY
Your LG Plasma TV will be repaired or replaced in accordance with the terms of this warranty, at LGE’s option, if it
proves to be defective in material or workmanship under normal use, during the warranty period (“Warranty Period”)
listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, including Alaska, Hawaii, and U.S. Territories.
WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
LABOR and PARTS: 2 YEARS from the Date of Purchase.
Your unit will be repaired or replaced with a new, substitute
model or factory reconditioned unit, at LGE’s option. If
repaired, parts used in the repair may be new or remanufactured.
Replacement Units and Repair Parts are warranted for the
remaining portion of the original unit’s warranty period.
In-Home Service: Please retain dealer’s
dated bill of sale or delivery ticket as evidence
of the Date of Purchase for proof of warranty,
and submit a copy of the bill of sale to the service person at the time warranty service is provided.
EFFECTIVE DATE OF WARRANTY: Your warranty period
begins on the date of sale to the original consumer/end user.
KEEP THE DEALER’S DATED BILL OF SALE OR PROOF OF
DELIVERY as evidence of the purchase date. You will be
required to submit a legible copy of your bill of sale or proof
of delivery when requesting warranty service.
Please call 1-201-816-2000 to locate your
nearest LGE Authorized Service Center.
Visit our website at:
http://www.lgservice.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE
EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS
WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY
NATURE, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR
DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some states do
not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal
rights and you may also have other rights that vary from state to state.
CONCERNING PIXEL FUNCTIONALITY: Your Plasma TV contains about one million individual pixels. Plasma TV
typically contain a small number of pixels that do not function normally. Your display has been inspected and is in
compliance with manufacturer’s specifications, indicating that any pixel defects do not effect the operation or use
of your display.
IMPORTANT: Please fill out and mail in your Product Registration Card or go to www.lgservice.com to register your
product online. This information will allow us to reach you promptly should we discover a safety or reliability problem that could affect you.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
●
●
●
●
●
●
●
●
damage caused in shipping or transit
service required as a result of improper installation,
including incorrect or insufficient AC supply (please
consult the owner’s manual for power supply
requirements)
installation or repair of antenna systems, cable converters, cable company supplied equipment, or
other components in a video system
set-up or adjustment on consumer controls, or
damage caused by improper adjustments
damage caused by other system components
any panel that has been modified or incorporated
into any other product
replacement of batteries on the remote control.
damage (including cosmetic damage), failure, loss
or personal injury due to misuse, abuse, negli-
●
●
●
●
●
gence, improper maintenance or storage, or to acts
of nature or other causes beyond our control.
(Causes beyond our control include but are not limited to lightning strike, power surges, power outages and water damage.)
image burn-in
repair or replacement of warranted parts by other
than LGE authorized service centers.
units purchased or serviced outside of the coverage
area.
product where the original factory serial numbers
have been removed, defaced or changed in any
way.
product sold and labeled as “as is, where is” or similar disclaimer.
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
CUSTOMER INTERACTIVE CENTER NUMBERS:
To obtain customer assistance, product
information or Dealer or Service locations
Call
1-201-816-2000
24 hours a day, 365 days per year
FOR SERVICE:
Before you call for warranty service, check your operating guide – you may avoid a service call.
For warranty service information, please contact the LGE Customer Interactive Center telephone number.
When calling for service, please have your product model number, serial number and the date of purchase or the date of original installation available.
If a replacement unit is required, under some circumstances you may be asked to provide a reserve deposit to
the LGE Service Center against a credit card number as surety for advanced shipment. Your credit card will not
be charged if you return the defective unit within 10 working days.
If a replacement unit is received, please use the carton and packaging from that unit in returning the defective
unit to the LG®Brand Service Center.
Parts and service in accordance with the LGE warranty are LGE’s responsibility and will be provided without
charge. Other service requirements will be at the owner’s expense. If you have problems in obtaining satisfactory
warranty service, write or call the LGE Customer Interactive Center. Service may be provided by independently
owned and operated service organizations.
To assure proper credit and avoid unnecessary charges, you must obtain an LGE Return Authorization before
returning any product to the LGE Service Center. Contact the Customer Interactive Center for details.
TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL:
LGE Customer Interactive Center
P.O. Box 240007
201 James Record Road
Huntsville, Alabama 35824
http://www.lgservice.com
P/NO : 3828VA0434A d