Chicago Electric 92496 Welder User Manual

HEAVY DUTY OXY - ACETYLENE
WELDING OUTFIT
Model 92496
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
Copyright© 2003 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
PRODUCT SPECIFICATIONS
Item
Torch Handle, Oxygen Regulator
and Acetylene Regulator
Construction
Cutting Nozzle Construction
Welding Nozzle and Heating
Nozzle Construction
Welding Hose Size and
Construction
Tip Cleaner Construction
Safety Glasses Construction
Flint Lighter Construction
Weight
Description
Polished finish, all brass construction
Brass and Steel. Chrome plated oxygen
lever. #1 Nozzle (For cutting material up to
¾” thickness)
Brass base with a Copper tip. VH-W2, #2
Nozzle (For welding material 1/16”-1/8”)
15 Ft. Long x 1/4” ID (each Hose)
Rubber and brass fittings
Steel files in an Anodized case
Plastic and Nylon, ANSI approved #10 Shade
Chrome plated steel with a Flint tip
19 Lbs.
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and assembly
diagram. Keep your invoice with this manual. Write the invoice number on the
inside of the front cover. Keep this manual and invoice in a safe and dry place for
future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1.
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
SKU 92496
PAGE 2
3.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
PERSONAL SAFETY
4.
Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
5.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
6.
Avoid accidental starting. Be sure the Power Switch is off before plugging in.
Carrying power tools with your finger on the Power Switch, or plugging in power
tools with the Power Switch on, invites accidents.
7.
Remove adjusting keys or wrenches before turning the power tool on. A wrench
or a key that is left attached to a rotating part of the power tool may result in personal
injury.
8.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
9.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
10.
Use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
11.
Do not force the tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
12.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must be
replaced.
13.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
SKU 92496
PAGE 3
TOOL USE AND CARE
14.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
15.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier to
control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.
16.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have the
tool serviced before using. Many accidents are caused by poorly maintained
tools.
17.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
18.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
19.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SKU 92496
PAGE 4
SPECIFIC SAFETY RULES
1.
Maintain labels and nameplates on the Heavy Duty Welding Kit. These carry
important information. If unreadable or missing, contact Harbor Freight Tools for
a replacement.
2.
Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of
obstructions, grease, oil, trash, and other debris.
3.
Prevent eye injury and burns. Wearing and using personal safety clothing and
safety devices reduce the risk for injury. Wear ANSI approved welding goggles
(such as those included in this kit) featuring at least a number 10 shade lens rating.
Leather leggings, fire resistant shoes or boots should be worn when using this
product. Do not wear pants with cuffs, shirts with open pockets, or any clothing that
can catch and hold molten metal or sparks. Keep clothing free of grease, oil, solvents,
or any flammable substances. Wear dry, insulating gloves and protective clothing.
Wear an approved head covering to protect the head and neck. Use aprons, cape,
sleeves, shoulder covers, and bibs designed and approved for welding and cutting
procedures. When welding or cutting overhead or in confined spaces, wear flame
resistant ear plugs or ear muffs to keep sparks out of ears.
4.
Prevent accidental fires. Remove any combustible material from the work area.
When possible, move the work to a location well away from combustible materials.
If relocation is not possible, protect the combustibles with a cover made of fire
resistant material. Remove or make safe all combustible materials for a radius of
35 feet (10 meters) around the work area. Use a fire resistant material to cover or
block all open doorways, windows, cracks, and other openings. Enclose the work
area with portable fire resistant screens. Protect combustible walls, ceilings, floors,
etc., from sparks and heat with fire resistant covers. If working on a metal wall,
ceiling, etc., prevent ignition of combustibles on the other side by moving the
combustibles to a safe location. If relocation of combustibles is not possible, designate
someone to serve as a fire watch, equipped with a fire extinguisher, during the
welding process and for at least one half hour after the welding is completed. Do
not weld or cut on materials having a combustible coating or combustible internal
structure, as in walls or ceilings, without an approved method for eliminating the
hazard. Do not dispose of hot slag in containers holding combustible materials.
Keep a fire extinguisher nearby and know how to use it. After welding or cutting,
make a thorough examination for evidence of fire. Be aware that easily visible
smoke or flame may not be present for some time after the fire has started. Do not
weld or cut in atmospheres containing dangerously reactive or flammable gases,
vapors, liquids, and dust. Provide adequate ventilation in work areas to prevent
accumulation of flammable gases, vapors, and dust. Do not apply heat to a container
that has held an unknown substance or a combustible material whose contents,
when heated, can produce flammable or explosive vapors. Clean and purge
containers before applying heat. Vent closed containers, including castings, before
preheating, welding, or cutting.
SKU 92496
PAGE 5
5.
Avoid overexposure to fumes and gases. Always keep your head out of the
fumes. Do not breathe the fumes. Use enough ventilation or exhaust, or both, to
keep fumes and gases from your breathing zone and general area. Where ventilation
is questionable, have a qualified technician take an air sampling to determine the
need for corrective measures. Use mechanical ventilation to improve air quality. If
engineering controls are not feasible, use an approved respirator. Work in a confined
area only if it is well ventilated, or while wearing an air-supplied respirator. Follow
OSHA guidelines for Permissible Exposure Limits (PEL’s) for various fumes and
gases. Follow the American Conference of Governmental Industrial Hygienists
recommendations for Threshold Limit Values (TLV’s) for fumes and gases. Have a
recognized specialist in Industrial Hygiene or Environmental Services check the
operation and air quality and make recommendations for the specific welding or
cutting situation.
6.
Always keep the Welding Hoses (D1A, or D1B) away from moving parts on the
tool. Examine the Welding Hoses for cuts, burns, or worn areas before each use.
If any damaged areas are found, replace the Welding Hoses immediately.
7.
Read and understand all instructions and safety precautions as outlined in
the manufacturer’s manual for the material you will weld or cut.
SKU 92496
PAGE 6
8.
Proper cylinder care. Secure cylinders to a cart, wall, or post, to prevent them
from falling. All cylinders should be used and stored in an upright position.
Never drop or strike a cylinder. Do not use cylinders that have been dented.
Cylinder caps should be used when moving or storing cylinders. Empty cylinders
should be kept in specified areas and clearly marked “empty”.
9.
Never use oil or grease on any inlet connector, outlet connector, or cylinder
valves.
10.
Always use reverse-flow check valves on the torch and regulator. This
greatly reduces the possibility of mixing gases in the regulator or hose.
11.
Working pressure on the Acetylene Regulator should NEVER be set above
15 PSI.
12.
There must be TWO O-Rings (C24, C25) on the Connector (C23) end. The
absence of either O-Ring can lead to flashback within the Torch
Handle
or
Cutting Attachment.
13.
For the Cutting Attachment, inspect the tapered seating surfaces on the
Tip and in the Torch Head. Have a qualified technician resurface the seat area
if it has dents, burrs, or is burned. A poor seating surface may result in backfire
or flashback.
14.
Backfire and flashback. When the flame goes out with a loud “pop”, it is called
a backfire. Backfire can be caused by (1) operating the Torch at lower pressures
than required for the Tip used, (2) touching the Tip against the workpiece, (3)
overheating the Tip, or (4) an obstruction in the Tip. If backfire occurs, shut off
the Torch Handle Valves (oxygen first) and after remedying the cause, relight the
Torch. A flashback is a condition that results when the flame flashes back into
the Torch and burns inside with a shrill hissing or squealing noise. If flashback
occurs, close the Torch Handle Valves (oxygen first), IMMEDIATELY. Flashback
generally indicates a problem that should be repaired. A clogged Tip, improper
functioning of the Valves, or incorrect acetylene/oxygen pressure could lead to
flashback. Make sure to find the cause before relighting the Torch.
15.
WARNING! This product, when used for welding and similar applications, contains or produces a chemical known to the State of California to
cause cancer and birth defects (or other reproductive harm).
(California Health & Safety Code 25249.5 et seq.)
16.
WARNING! The brass components of this product contain lead, a
chemical known to the State of California to cause birth defects (or other
reproductive harm). (California Health & Safety Code 25249.5 et seq.)
SKU 92496
PAGE 7
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists on pages 1519 are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
ASSEMBLY AND OPERATING INSTRUCTIONS
For additional information regarding the parts listed in the following pages, refer
to the Parts Diagrams on pages 15-19.
1.
NOTE! The following instructions are for acetylene gas use only.
Contact your gas supplier for instructions on the use of other fuel gases.
2.
Make sure to secure the cylinders (as noted in the Specific Safety Rules section).
3.
While standing to one side, “crack” each cylinder valve. “Cracking” is to quickly
open and close the valve, allowing gas to escape and clearing the valve of any
foreign material.
WARNING! If oil or grease is found, discontinue using
cylinder and immediately contact your supplier. (See Figure D.)
QUICKLY
OPEN/CLOSE
VALVE TO
“CRACK”
CYLINDER
VALVE
HANDLE
ACETYLENE
OR
OXYGEN
CYLINDER
(NOT INCLUDED)
FIGURE D
4.
Attach the GREEN Oxygen Regulator (parts A1-A20E) to the oxygen cylinder. Then,
attach the RED Acetylene Regulator (parts 1-19) to the acetylene cylinder. Make
sure they are tightened in the correct directions (normally, clockwise for oxygen and
counterclockwise for acetylene.)
(See Figure E, next page.)
SKU 92496
PAGE 8
5.
IMPORTANT! The Pressure Adjusting Screw (18) on the Acetylene Regulator and
the Pressure Adjusting Screw (A18) on the Oxygen Regulator should be opened
slightly by turning counterclockwise to relieve pressure on the Regulator diaphragms
before opening the cylinder valves. If this is not done, pressure from the cylinders
may damage the diaphragms and render the Regulators inoperable.
RED
OXYGEN
REGULATOR
(PARTS A1-A20E)
WELDING NOZZLE (D4),
OR CUTTING NOZZLE (D6)
CYLINDER
VALVE
PRESSURE
ADJUSTING
SCREW
(A18)
GREEN
ACETYLENE
REGULATOR
(parts 1-19)
PRESSURE
ADJUSTING
SCREW
(18)
CUTTING
ATTACHMENT
(PARTS C1-C27)
TORCH
HANDLE
(PARTS B1-B10)
CYLINDER
VALVE
RED
WELDING
HOSE
(D1B)
ACETYLENE
CYLINDER
(NOT INCLUDED)
GREEN
WELDING
HOSE
(D1A)
OXYGEN
CYLINDER
(NOT INCLUDED)
FIGURE E
6.
Connect the GREEN and RED Welding Hoses (D1A, or D1B) to the proper connections on the Torch Handle (parts B1-B10).
WARNING! If any traces of oil or grease are found, do not use. Contact
SKU 92496
PAGE 9
your gas supplier immediately. (See Figure F.)
TORCH HANDLE
(PARTS B1-B10)
FIGURE F
7.
GREEN (OX) WELDING HOSE
(D1A)
RED (AC) WELDING HOSE (D1B)
Connect the Cutting Attachment (parts C1-C27) to the Torch Handle (parts B1B10). Always check the Connector (C23) and Coupling Nut (C22) for damage or oil.
If either are found, discontinue use and contact your gas supplier.
WARNING!
Make sure the two O-Rings (C24, C25) are not damaged or
missing, otherwise gases will mix inside the Torch Handle (parts B1-B10)
and result in flashback or backfires. (See Figures G, and H.)
CUTTING ATTACHMENT (PARTS C1-C27)
CONNECTOR (C23)
COUPLING NUT (C22)
O-RING O-RING
(C24)
(C25)
FIGURE G
CUTTING ATTACHMENT (PARTS C1-C27)
FIGURE H
8.
TORCH HANDLE (PARTS B1B10)
GREEN (OXYGEN)
WELDING HOSE
(D1A)
RED (ACETYLENE)
WELDING HOSE
(D1B)
Check connections for leaks. Adjust the Acetylene Regulator (parts 1-19) and
Oxygen Regulator (parts A1-A20E) to their normal operating pressure. Use an
approved leak detection solution to check for leaks at the Welding Hoses (D1A, and
D1B) and cylinder valve connections. If leaks are found, tighten the nuts more
SKU 92496
PAGE 10
securely. If a leak still persists, discontinue use and call your gas supplier.
WARNING! NEVER set the Acetylene Regulator (parts 1-19) to a delivery
pressure above 15 PSI. (See Figures I, J, and K.)
WELDING TIP CHART
Metal Thickness
Oxygen Pressure Acetylene Pressure
P.S.I.G.
P.S.I.G.
Tip Size
1/64” - 3/64”
1/32” - 5/64”
3/64” - 3/32”
1/16” - 1/8”
1/8” - 3/16”
3/16” - 1/4”
1/4” - 1/2”
00
Min.
3
0
1
2
3
4
5
3
3
3
4
5
6
Max.
Min.
Max.
5
5
5
5
7
10
12
3
3
3
3
3
4
5
5
5
5
5
6
7
8
FIGURE I
OXY-ACETYLENE MULTI-FLAME HEATING CHART
Acetylene
Pressure
Range
P.S.I.G.
Oxygen
Pressure
Range
P.S.I.G.
6
4-6
8
8 - 12
Tip Size
Acetylene Cubic Oxygen Cubic
Feet Per Hour Feet Per Hour
Min.
Max.
Min.
Max.
8 - 11
14
40
15
44
10 - 18
30
80
33
88
FIGURE J
OXY-ACETYLENE CUTTING NOZZLE CHART
Metal Thickness
Oxygen
Pressure
P.S.I.G.
Nozzle Size
Min.
Max.
1/2”
0
30
35
3
5
3/4”
1
30
35
33
5
FIGURE K
SKU 92496
Acetylene
Pressure
P.S.I.G.
Min.
Max.
PAGE 11
9.
To determine the proper Acetylene Regulator (parts 1-19) pressure and
Oxygen Regulator (parts A1-A20E) pressure for neutral flame adjusting,
refer to Figures I, and K.
HIGH PRESSURE LEVER
(C20)
PRE-HEAT OXYGEN CONTROL VALVE
(C26)
CUTTING
NOZZLE
FIGURE L
(D6)
OXYGEN CONTROL VALVE
(B8 with OX Label (B9))
ACETYLENE CONTROL VALVE
(B8 with AC Label (B10))
10.
Depending on use, attach either a Cutting Nozzle #1 (D6), or Welding Nozzle #2
(D4) to the Cutting Attachment (parts C1-C27).
(See Figure L.)
11.
Open the Oxygen Control Valve (B8 with label (B9)) on the Torch Handle. Open the
Pre-Heat Oxygen Valve (C26) on the Cutting Attachment. Adjust the Oxygen
Regulator (parts A1-A20E) to the desired working pressure. Then, close the Oxygen
Control Valve on the Torch Handle. (See Figures E, and L.)
12.
Open the Acetylene Control Valve (B8 with label (B10)) on the Torch Handle. Adjust
the Acetylene Regulator (parts 1-19) to the desired working pressure. Then, close
the Acetylene Control Valve on the Torch Handle.
(See Figures E, and L.)
13.
Hold the Torch Handle (parts B1-B10) in one hand and the Flint Lighter (D9) in the
other hand. (See Figure M.)
FIGURE M
FLINT LIGHTER (D9)
SKU 92496
ACETYLENE
CONTROL
VALVE
(B8 with AC Label (B10))
PAGE 12
14.
Open the Acetylene Control Valve (B8 with AC Label (B10)) about 1/4 turn, and
ignite the acetylene gas coming out of the Nozzle (part D4).
WARNING! Always point the Nozzle away from other people when
lighting. (See Figures L, and M.)
15.
Slowly open the Acetylene Control Valve (B8 with AC Label (B10)) further until the
smoke subsides and the flame jumps away from the end of the Nozzle (part D4)
slightly. (See Figure M.)
16.
Slowly open the Oxygen Control Valve (B8 with OX Label (B9)) until a brilliant neutral
flame is reached. (If the flame has a smooth inner cone, the flame is called neutral.)
(See Figure N.)
17.
WARNING! Always use appropriate welding goggles or welding
helmet when welding or cutting (at least a #10 shade lens rating).
OXYGEN CONTROL VALVE
(B8 with OX Label (B9))
NOZZLE (PARTS D4)
ACETYLENE
CONTROL VALVE
(B8 with AC Label (B10))
FIGURE N
18.
Once the welding or cutting job is competed, turn off the Oxygen Control Valve (B8
with OX Label (B9)). Then, turn off the Acetylene Control Valve (B8 with AC Label
(B10)).
NOTE: Reversal of this procedure may cause damage to the Torch Handle
(parts B1-B10). (See Figure N.)
19.
Shut off both cylinder valves. (See Figure E.)
20.
Drain the gas from the Oxygen Regulator (parts A1-A20E) by opening the Oxygen
Control Valve (B8 with OX Label (B9)). Complete this Step on the acetylene side.
(See Figure N.)
21.
Release the pressure on the Acetylene and Oxygen Regulators by turning their
Pressure Adjusting Screws (18, A18) counterclockwise. (See Figure E.)
SKU 92496
PAGE 13
INSPECTION, MAINTENANCE, AND CLEANING
1.
WARNING! Make sure the Welding Kit is cool to the touch and
disconnected from its oxygen and acetylene cylinders before performing
any inspection, maintenance, or cleaning procedures.
2.
BEFORE EACH USE, inspect the general condition of the Welding Kit. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts,
damaged Welding Hoses (D1A, or D1B), and any other condition that may affect its
safe operation. If a problem occurs, have the problem corrected before further use.
Do not use damaged equipment.
3.
PERIODICALLY, use the Tip Cleaner (D7) to clean out dirt and debris from the
Nozzle (parts D4). Make sure to use the correct size Tip Cleaner for each individual
Nozzle. (See Assy. Diagram E.)
4.
TO CLEAN, use a clean cloth. If necessary, a mild detergent may be used.
Do not immerse any part of the Welding Kit in liquid.
Do not use solvents or other flammable agents to clean the Welding Kit.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER
THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
SKU 92496
PAGE 14
PARTS LIST AND DIAGRAM 1 - ACETYLENE REGULATOR
Note: When ordering parts from
this parts list and diagram
always take the number from
the No. column (on the left).
For example: If you wish to order
a Body for this regulator you’d
take the part number from the
No. column (1). So you’d
order part 1.
Components Of: #12
Item
No.
Description
Item
No.
1
2
3
4
5
6
7
8
9
10
11
12
Body
H.P. Gauge (2.1” x 400psi/2800kpa)
L.P. Gauge (2.1” x 30psi/200kpa)
Inlet Nut (CGA 510)
Inlet Spigot
Filter
Valve Spring
Anti-Vibrator
Valve
Nozzle
Plunger
Diaphragm Assembly
12A
12B
12D
13
14
15
16
17
18
19
Description
Nut
Diaphragm Plate
12C
Diaphragm
Centralizer
Slip Ring
Adjusting Spring
Spring Button
Bonnet
Label
Adjusting Screw “T” Bar
Outlet Adaptor
NOTE: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
SKU 92496
PAGE 15
PARTS LIST AND DIAGRAM 2 - OXYGEN REGULATOR
Note: When ordering parts from this
parts list and diagram always take
the number from the No. column
(on the left) and add a suffix of A to
the beginning.
For example: If you wished to order a
Filter for this regulator you’d take the
part number from the No. column (6)
and add an A to the beginning. So
you’d order part A6.
Components Of: #12
Components Of: #20
Item
No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
12A
12B
Body
H.P. Gauge (2.1” x 4000psi/28000kpa)
L.P. Gauge (2.1” x 200psi/1400kpa)
Inlet Nut (CGA 540)
Inlet Spigot
Filter
Valve Spring
Anti-Vibrator
Valve
Nozzle
Plunger
Diaphragm Assembly
Nut
Diaphragm Plate
Item
No.
Description
12C
12D
13
14
15
16
17
18
19
20
20A
20B
20C
20D
20E
Diaphragm
Centralizer
Slip Ring
Adjusting Spring
Spring Button
Bonnet
Label
Adjusting Screw “T” Bar
Outlet Adaptor
Safety Valve
Safety Body
Safety Rubber
Safety Seat
Safety Spring
Safety Cap
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 92496
PAGE 16
PARTS LIST AND DIAGRAM 3 - TORCH HANDLE
Components Of: #8
Note: When ordering parts from this
parts list and diagram always take
the number from the No. column
(on the left) and add a suffix of B
to the beginning.
For example: If you wished to order a
Tail for this handle you’d take the
part number from the No. column
(4) and add an B to the beginning.
So you’d order part B4.
Item
No
Description
Item
No
Description
1
2
3
4
5
6
7
Torch Head
Handle
Inner Tube
Tail
Oxygen Valve Body
Gas Valve Body
Cover
8
8A
8B
8C
8D
9
10
Valve Stem Assembly
Valve
Washer
Nut
Adjusting Knob
Label (OX)
Label (AC)
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 92496
PAGE 17
PARTS LIST AND DIAGRAM 4 - CUTTING ATTACHMENT
Note: When ordering parts from this parts list and
diagram always take the number from the No.
column (on the left) and add a suffix of C to
the beginning.
For example: If you wished to order a Head for this
attachment you’d take the part number from
the No. column (2) and add an C to the
beginning. So you’d order part C2.
Components Of: #26
Item
No
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Tip Nut
Head
Oxygen Tube
Nut
Ferrule
Nut
Fuel Tube
Inner Tube (A)
Inner Tube (B)
Spiro
Inner Tube (C)
O-Ring
Washer (Teflon)
Spring
Body
Valve
Item
No
Description
17
18
19
20
21
22
23
24
25
26
26A
26B
26C
26D
27
HP Spring
Washer
Valve Cap
Lever
Sprial Pin
Coupling Nut
Connector
O-Ring (Big)
O-Ring (Small)
Valve Stem Assembly
Valve
Washer
Nut
Adjusting Knob
Label (OX)
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 92496
PAGE 18
PARTS LIST AND DIAGRAM 5 - ACCESSORY PARTS
Note: When ordering parts from this
parts list and diagram always take
the number from the No. column
(on the left) and add a suffix of D
to the beginning.
For example: If you wished to order a
Welding nozzle you’d take the part
number from the No. column (4)
and add an D to the beginning.
So you’d order part D4.
Item
No
Description
1A
1B
4
6
7
Green (OX) Welding Hose
Red (AC) Welding Hose
Welding Nozzle (#2)
Cutting Nozzle #1
Tip Cleaner
Item
No
Description
8
9
10
11
Safety Glasses
Flint Lighter
Oxygen Check Valve
Acetylene Check Valve
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 92496
PAGE 19