Chief Manufacturing MSP-CM6HABV71/83 Crib Toy User Manual

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Automated Vertical Panel Lift
This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television
communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment to an outlet on a circuit other than that to which the receiver is connected
Consult the dealer or and experienced radio/TV technician for help
MSP-CM6HABV71/83
MSP-CM6HABV71/83
Installation Instructions
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However,
CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV
assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
IMPORTANT WARNINGS AND CAUTIONS!
The Alert messages DANGER, WARNING, CAUTION, IMPORTANT, and NOTE are used throughout these instructions and on the
product to alert the reader and/or operator of the existence of dangerous situations, conditions and/or important operational and
maintenance information.
"SAVE THESE INSTRUCTIONS"
WARNING: WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: FAILURE TO READ AND FOLLOW THE FOLLOWING INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL
INJURY, DAMAGE TO EQUIPMENT OR VOIDING OF FACTORY WARRANTY. It is the installer’s responsibility to make sure all
components are properly assembled and installed using the instructions provided. Read all instructions before using this
furnishing.
DANGER: TO REDUCE THE RISK OF ELECTRIC SHOCK:
•
ALWAYS unplug this furnishing from the electrical outlet before cleaning.
WARNING: TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
•
•
•
•
•
•
•
•
•
•
Unplug from outlet before putting on or taking off parts.
Close supervision is necessary when this furnishing is being used by, or near, children, invalids, or disabled
persons.
Use this furnishing only for its intended use as directed in these instructions. DO NOT use attachments not
recommended by the manufacturer.
NEVER operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and
repair.
Keep the cord away from heated surfaces.
NEVER operate the furnishing with the air openings blocked. Keep the air openings free of lint, and the like.
NEVER drop or insert anything into any opening.
DO NOT use outdoors.
DO NOT operate where aerosol (spray) products are being used, or where oxygen is being administered.
To disconnect, turn all controls to the off position, then remove plug from outlet.
WARNING: RISK OF ELECTRICAL SHOCK! Connect this device to a properly grounded outlet only.
CAUTION: ONE END OF POWER CORD MUST REMAIN ACCESSIBLE AT ALL TIMES! DO NOT block or impede access to
plug at any time!
CAUTION: Changes or modifications to this unit not expressly approved by the manufacturer can void the units FCC
compliance rating and make the unit illegal to operate.
2
Installation Instructions
MSP-CM6HABV71/83
ASSEMBLY
1.
Attach cables to weights by hand and tighten retaining nut using a 7/16" wrench.
Figure 1
3
MSP-CM6HABV71/83
Installation Instructions
INSTALLATION
1.
Screw tracks to cabinet using 1/8” masonite space. (provides screw head clearence for double wall)
Figure 2
4
Installation Instructions
2.
MSP-CM6HABV71/83
Level cabinet in both directions.
Figure 3
5
MSP-CM6HABV71/83
3.
Installation Instructions
Attach door plates 1 inch down from the top with the “V” notch aligned with the panel edge.
Figure 4
6
Installation Instructions
4.
MSP-CM6HABV71/83
Gently push to make sure that wheels are touching track.
Figure 5
7
MSP-CM6HABV71/83
5.
6.
Installation Instructions
Remove nuts from the studs on the wheel plates and place the panel on the mechanism.
Center the panel and tighten the nuts.
Figure 6
8
Installation Instructions
7.
MSP-CM6HABV71/83
While holding back the chain attachment bracket, move the door up and down to check for balance. Also check to see if the
counterweights hit or rub the cabinet. If it does, it’s not level.
Figure 7
9
MSP-CM6HABV71/83
8.
Installation Instructions
If the panel seems light, add weight to it. If the panel seems heavy, add weight to the counterweights.
Figure 8
10
Installation Instructions
MSP-CM6HABV71/83
RF Receiver Installation
ADJUSTMENTS
Install RF reciever following the instructions provided with the
receiver.
Adjust Door Travel Distance
System Activation
1.
To adjust door travel distance:
1.
Insert plug from the power supply into the jack on the top of
the motor box.
24VDC Input
Top of
Cabinet
Set the length of travel required using the adjustable stop on
the bottom of the left hand track.
2. Press and hold the activator button on the front of the motor
box for 13 seconds.
The Status Light on the front of the motor box will begin to blink
alternately red and green. When this starts to happen release
the Activator Button. When put into "Learn Moden the system
runs back and forth several times and measures it's
environment, such as open and closed locations etc. The
system will then stop and remember these learned
measurements.
Activator
Figure 11
System Controls and Indicators
Front of
Cabinet
Learn Mode
recommended.
The CM6SV system has no limit switches. The system uses an
encoder on the motor to collect data and send it to the micro
processor’s memory. The software "learns" about its
environment (speed, time duration, stop points, etc.) during the
initial setup of the unit and retains that information until
requested to "relearn" its environment.
3.
4.
The unit is shipped pre-set from the factory and will then
continually adjusts to it’s enviornment on each activation.
Figure 9
2.
Plug Powercord into 115VAC outlet.
IMPORTANT ! : A quality surge protection device is
Make sure nothing is obstructing movement of doors,
Press and release the Activator Button on the front of the
Motor Box or the "Close Door button on the Remote Control.
(The doors should travel to the fully closed position)
Activator
If for some reason you want to place the system into “Learn
Mode” (such as to stop at other than its normal stop points),
Press and hold the red activator button on the front of the motor
box for approxamatly 13 seconds and then release it when the
Status Light flashes quickly red, green, red, green, red, green.
Activator Button
Figure 10
5.
Press the "Open Door" button on the Remote Control.
NOTE: The mechanism has been preset to travel 34 inches. If
a different travel distance is required see "Door Travel
Adjustment below.
Figure 12
The controller will then be in “Learn Mode” (The door will move
for 3 seconds, stop for 10 seconds, and when it starts moving
again it will be in it’s “Learn Mode”).
When put into “Learn Mode” the mechanism runs back and
forth several times and measures it’s environment, such as
open and closed locations etc., and then stops and remembers
11
MSP-CM6HABV71/83
Installation Instructions
these learned measurements, so that next time the system runs
it knows where to start and stop.
Status Light Codes
There is a light on the front of the mechanism motor box that
will tell through its pattern of flashes and colors what the
mechanism is doing.
Power Loss - The Status Light will be on solid red. ---- There
has been a power loss (due to an electrical storm, etc.). When
next activated the doors will move at a slow speed to their full
closed position. If the doors are already closed they will not
move. The Status Light will return to solid green and the doors
are ready for normal activation.
Optional Control Input Connections
Control Input- 8 position RJ 45 modular phone jack
Status Indicator
Discrete control for use with 3rd party control.
•
Position 8- Open
•
Position 7- Stop
IR Receiver “Eye” input for Eubank, Inc. supplied external IR
reciever only.
•
Position 6 - V out
•
Position 5 - Vcc, 5v
Radio Power for external RF reciever only.
Figure 13
•
Position 4 - 24 VDC
Sequence control for use with 3rd party control.
Normal Doors At Rest - The Status Light will be on steady
green.
Normal Run Motion of Doors - The Status Light will flash in
groups of 2 green followed by a pause. In normal run motion
the doors on a Eubank mechanism have a variable speed. The
doors will start slowly, accelerate to a fast speed, and then slow
down before coming to a stop.
•
Position 3 - Sequence- Open, Stop, Close, Stop
•
Position 2 - Common
Discrete control for use with 3rd party control.
•
Control Input on Front of Motor Box
Doors Obstructed - The Status Light will flash in groups of 3
red followed by a pause. If the doors meet an obstruction they
will sense the obstruction, stop momentarily, and move in the
opposite direction for a few seconds. ---- Remove the
obstruction and then activate the doors. They should return to
normal run motion.
Control Input
Doors Obstructed Both Ways - The Status Light will flash in
groups of 4 red followed by a pause. Similar to Doors
Obstructed but doors are prevented from moving in either
direction. ---- Remove the obstruction and then activate the
doors. They should return to normal run motion.
Travel Too Far - The Status Light will flash in groups of 5 red
followed by a pause. The motor is running but the doors are
not moving. ---- Has the motor box been uncoupled from the
track, or is the motor box bent, causing it to become uncoupled
from the track?
Position 1 - Close
Figure 14
NOTE: Making a momentary dry contact closure between the
common and the open, closed, stop, or sequence will
activate the system in that mode.
Control Input on Front of Motor Box
Figure 15
12
Installation Instructions
MSP-CM6HABV71/83
13
MSP-CM6HABV71/83
Installation Instructions
USA/International
Europe
Asia Pacific
8820-000025
2007 Chief Manufacturing
www.chiefmfg.com
05/07
A
P
F
A
P
F
A
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
P +86-755-8996 9226 ; 8996 9236 ; 8996 9220
F +86-755-8996 9217
Download PDF

advertising