Cisco Systems 1010 Network Card User Manual

Doc. No. 78-5172-01
Installing the Cisco RPS Adapter Plate
in Cisco 2600 Series Routers
Product Number: ACS-2600RPS=
This document describes how to install an adapter plate in Cisco 2600 series routers for use with the
Cisco Redundant Power System (RPS). The Cisco RPS provides power system redundancy to
external devices (such as routers, switches, or hubs). The system includes two fully redundant AC
input power modules and four DC output power modules for connection to external devices. The
Cisco RPS supports quasi-redundant and fully redundant power source configurations. To use the
Cisco RPS with Cisco 2600 series routers, you must remove the existing power supply and replace
it with a Cisco RPS adapter plate.
This document includes the following sections:
•
•
•
•
•
•
•
•
Safety Recommendations on page 1
Required Tools and Equipment on page 4
Removing the Cover on page 5
Removing the Power Supply on page 7
Installing the Redundant Power Supply Adapter Plate on page 8
Obtaining Service and Support on page 11
Cisco Connection Online on page 11
Ordering Documentation on page 12
Safety Recommendations
Follow these guidelines to ensure general safety:
•
•
Keep the chassis area clear and dust-free during and after installation.
Put the removed chassis cover in a safe place.
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Copyright © 1998
Cisco Systems, Inc.
All rights reserved.
1
Safety Recommendations
•
•
Keep tools away from walk areas where you or others could fall over them.
•
•
Wear safety glasses when working under any conditions that might be hazardous to your eyes.
Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll
up your sleeves.
Do not perform any action that creates a potential hazard to people or makes the equipment
unsafe.
Safety Warnings
Safety warnings appear throughout this publication in procedures that, if performed incorrectly,
might harm you. A warning symbol precedes each safety warning.
Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before
you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents.
Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust
te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van
standaard maatregelen om ongelukken te voorkomen.
Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan.
Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä
vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista.
Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation
pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement,
soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les
procédures couramment utilisées pour éviter les accidents.
Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer
Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie
sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur
Vermeidung von Unfällen bewußt.
Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare
infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli
relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti.
Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til
personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som
elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.
Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos
físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos
relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir
possíveis acidentes.
¡Advertencia! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física.
Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y
familiarizarse con los procedimientos estándar de prevención de accidentes.
Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till
personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med
elkretsar och känna till vanligt förfarande för att förebygga skador.
2 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
Safety with Electricity
To see translations of the remaining warnings that appear in this publication, refer to the Regulatory
Compliance and Safety Information document that accompanied the device.
Safety with Electricity
Follow these guidelines when working on equipment powered by electricity:
Warning Read the installation instructions before you connect the system to its power
source.
Warning Ultimate disposal of this product should be handled according to all national
laws and regulations.
Warning Only trained and qualified personnel should be allowed to install or replace this
equipment.
Warning Before working on a chassis or working near power supplies, unplug the power
cord on AC units; disconnect the power at the circuit breaker on DC units.
Warning Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when connected to
power and ground, and can cause serious burns or weld to the terminals.
•
Locate the emergency power-OFF switch in the room in which you are working. Then, if an
electrical accident occurs, you can quickly shut the power OFF.
•
Disconnect all power before doing the following:
— Installing or removing a chassis
— Working near power supplies
•
•
•
Do not work alone if potentially hazardous conditions exist.
•
If an electrical accident occurs, proceed as follows:
Never assume that power is disconnected from a circuit. Always check.
Look carefully for possible hazards in your work area, such as moist floors, ungrounded power
extension cables, and missing safety grounds.
— Use caution; do not become a victim yourself.
— Turn OFF power to the system.
— If possible, send another person to get medical aid. Otherwise, determine the condition of the
victim and then call for help.
— Determine if the person needs rescue breathing or external cardiac compressions; then take
appropriate action.
Caution Use the Cisco RPS (model PWR600-AC-RPS) only to power the external
device.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
3
Required Tools and Equipment
Seul le système d’alimentation redondant Cisco (RPS modèle PWR600-AC-RPS) doit servir à
alimenter le dispositif externe.
Das externe Gerät darf nur mit einer redundanten Stromversorgung von Cisco, Modell
PWR600-AC-RPS, betrieben werden.
Para alimentar el dispositivo externo, usar exclusivamente el sistema de alimentación redundante
(redundant power system = RPS) Cisco, modelo PWR600-AC-RPS.
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when
electronic printed circuit cards are improperly handled and can result in complete or intermittent
failures. Always follow ESD prevention procedures when removing and replacing cards. Ensure that
the chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap, ensuring
that it makes good skin contact. Connect the clip to an unpainted surface of the chassis frame to
safely channel unwanted ESD voltages to ground. To properly guard against ESD damage and
shocks, the wrist strap and cord must be used correctly. If no wrist strap is available, ground yourself
by touching the metal part of the chassis.
Caution For safety, periodically check the resistance value of the antistatic strap, which
should be between 1 and 10 megohms (Mohm).
Required Tools and Equipment
This kit includes the following items:
•
•
Cisco RPS adapter plate, shown in Figure 1
DC power rating label
4 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
Removing the Cover
Figure 1
Cisco RPS Adapter Plate for Cisco 2600 series Routers
d
Adapter plate
H9430
e
rs
ue
et ut
ct nt
se u
on incid at.
c
t
,
et od lutp
am m vo
it is at
r s eu er
lo h
do ib am
:
G m y n liqu
N
u m
I
N ips um a a
AR m n gn
W ore no ma
L iam re
d olo
d
To install the Cisco RPS adapter plate, you will also need the following tools and equipment (which
are not included):
•
•
•
•
•
Cisco 2600 series router
Medium-size Phillips screwdriver
ESD-preventive wrist strap
Antistatic bag (optional)
Wire cutters or scissors for cutting the cable tie-wraps (optional)
Removing the Cover
You must remove the chassis cover to access the internal power supply.
Warning Do not touch the power supply when the power cord is connected. For systems
with a power switch, line voltages are present within the power supply even when the
power switch is OFF and the power cord is connected. For systems without a power
switch, line voltages are present within the power supply when the power cord is
connected.
Warning Before performing any of the following procedures, ensure that power is
removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker
on the panel board that services the DC circuit, switch the circuit breaker to the OFF
position, and tape the switch handle of the circuit breaker in the OFF position.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
5
Removing the Cover
Take these steps to remove the chassis cover:
Step 1
Power OFF the router.
Step 2
Attach an ESD-preventive wrist strap.
Step 3
Disconnect all cables from the rear panel of the router.
Warning Before opening the chassis, disconnect the telephone-network cables to avoid
contact with telephone-network voltages.
Warning Do not work on the system or connect or disconnect cables during periods of
lightning activity.
Step 4
Place the router so that the front panel is facing you. Remove the screws located on top
of the cover near the front edge.
Step 5
Slide the cover away from you until the metal tabs on the side edges separate from the
chassis bottom, as shown in Figure 2.
Figure 2
Removing the Cover
POWER
RPS
ACTIVITY
Lift the front edge of the cover until it clears the front of the chassis, as shown in Figure 3.
Step 6
Figure 3
Lifting the Cover
Step 7
RPS
SERIES
H11659
Cisco 2600
POWER
SERIES
H11658
Cisco 2600
ACTIVITY
Lift the cover until it is free from the chassis and then set it aside.
6 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
Removing the Power Supply
Removing the Power Supply
This section describes how to remove the internal power supply. Although the AC power supply is
shown in the illustrations that follow, the procedure is the same for removing both the AC and DC
power supplies.
Take these steps to remove the power supply:
Step 1
Locate the six-pin connector on the system board near the front of the router, and
disconnect it. (See Figure 4.)
Note If cable tie-wraps on the harness interfere with removing the connectors, cut the
tie-wraps, being careful not to cut the power supply wires.
Figure 4
Locating the Connectors
AC power supply
H9081
Fan
Power connector
Fan connector
Remove the mounting screw that secures the power supply to the chassis. (See Figure 5.)
Set aside this screw for later use.
Figure 5
Removing the Mounting Screw
Input: 100-240VAC
Freq: 50/60 Hz
Current: 1.2-0.6A
Watts: 40W
H9079
Step 2
1
0
Screw
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
7
Installing the Redundant Power Supply Adapter Plate
Step 3
Slide the power supply forward slightly in the chassis. This disengages the built-in hooks
that help secure the power supply to the chassis. (See Figure 6.)
Figure 6
Removing the Power Supply
Fan
H9082
AC power supply
Step 4
Place the removed screw and power supply in an antistatic bag.
Installing the Redundant Power Supply Adapter Plate
Take these steps to install the Cisco RPS Adapter Plate:
Step 1
Place the router so that the rear panel is facing you. (See Figure 7.)
Figure 7
Cisco 2600 Series Rear Panel (Cisco 2610 Shown)
Cisco 2610
SERIAL 1
Cisco 2610
SERIAL 1
SERIAL 0
CONN
WIC
CONN 2A/S
SERIAL 0
CONN
SEE MANUAL BEFORE INSTALLATION
CONN
100-240V– 1A
50/60 Hz 47 W
WIC
2T
SEE MANUAL BEFORE INSTALLATION
W1
W0
Step 2
CONSOLE
AUX
Console
port (RJ-45)
Auxiliary port
(RJ-45)
H11580
LINK ETHERNET 0 ACT
Ethernet 0/0
10BaseT
port (RJ-45)
Attach the DC power rating label over the ratings on the rear panel of the router.
(See Figure 8.)
Figure 8
Attaching the DC Power Rating Label
CISCO2610
100-240V~ 1.5A/0.75A
50/60 Hz
Label
SERIAL 1
SERIAL 0
CONN
WIC
2T
SEE MANUAL BEFORE INSTALL
ATION
LINK
ACT
ETHERNET 0
Cisco 2610
W0
CONSOLE
AUX
8 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
10748
CONN
Installing the Redundant Power Supply Adapter Plate
Align the Cisco RPS Adapter Plate with the chassis cutout for the power supply. Tilt the
adapter plate slightly toward you at the top, and rock it up and into place, ensuring that
the two small hooks at the top of the Adapter Plate engage the router chassis. (See
Figure 9.)
Step 3
Figure 9
Installing the Cisco RPS Adapter Plate
H9801
Front of chassis
Install the mounting screw that came with the Cisco RPS Adapter Plate into the screw
hole. (See Figure 10.)
Step 4
Figure 10
Installing the Mounting Screw
H9805
DC INPUT FOR USE WITH CISCO RPS
+5V– – –10A, +12V– – –2A, -12V– – –1A
Mounting
screw
Step 5
Connect the six-pin connector to the system board. The connector is keyed so that it
cannot be connected to the system board incorrectly. (See Figure 11.)
Step 6
Connect the 4-pin environmental status connector only if your router, with the connector
connected, has been upgraded to the correct level of Cisco IOS software. Using any other
level of Cisco IOS software can cause the router to crash. Cisco IOS Release 11.1(12)AA
or later is compatible but will not show status from the RPS. Cisco IOS Release 11.2(7)P
or later will provide RPS status information to the network.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
9
Installing the Redundant Power Supply Adapter Plate
Reconnecting the Connectors
10345
Figure 11
Six-pin
connector
Replacing the Cover
Take the following steps to replace the cover:
Step 1
Position the two chassis sections, as shown in Figure 2.
Step 2
Referring to Figure 2, press the two chassis sections together and ensure the following:
•
The top section fits into the rear of the bottom section. The bottom section fits into the
front of the top section.
•
Each side of the top and bottom sections fits together.
Caution To fit the two sections together, it might be necessary to work them together at
one end and then the other, working back and forth; however, use care to prevent bending
of the chassis edges.
Step 3
When the two sections fit together snugly, slide the chassis top so until it fits into the front
bezel.
Step 4
Replace the cover screws. Tighten the screws to no more than 8 or 9 inches/pound of
torque.
Step 5
Reinstall the chassis on the wall, rack, desktop, or table.
Step 6
Reconnect all cables.
10 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
Obtaining Service and Support
Obtaining Service and Support
For service and support for a product purchased from a reseller, contact the reseller. Resellers offer
a wide variety of Cisco service and support programs, which are described in the section “Service
and Support” in the information packet that shipped with your chassis.
Note If you purchased your product from a reseller, you can access Cisco Connection Online
(CCO) as a guest. CCO is Cisco Systems’ primary, real-time support channel. Your reseller offers
programs that include direct access to CCO’s services.
For service and support for a product purchased directly from Cisco, use CCO.
Cisco Connection Online
Cisco Connection Online (CCO) is Cisco Systems’ primary, real-time support channel. Maintenance
customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added
services to Cisco’s customers and business partners. CCO services include product information,
product documentation, software updates, release notes, technical tips, the Bug Navigator,
configuration notes, brochures, descriptions of service offerings, and download access to public and
authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced
simultaneously: a character-based version and a multimedia version that resides on the World Wide
Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet
e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version
of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well
as hyperlinks to related information.
You can access CCO in the following ways:
•
•
•
•
•
WWW: http://www.cisco.com
WWW: http://www-europe.cisco.com
WWW: http://www-china.cisco.com
Telnet: cco.cisco.com
Modem: From North America, 408 526-8070; from Europe, 33 1 64 46 40 82. Use the
following terminal settings: VT100 emulation; databits: 8; parity: none; stop bits: 1; and
connection rates up to 28.8 kbps.
For a copy of CCO’s Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For
additional information, contact cco-team@cisco.com.
Note If you are a network administrator and need personal technical assistance with a Cisco
product that is under warranty or covered by a maintenance contract, contact Cisco’s Technical
Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general
information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387,
408 526-7208, or cs-rep@cisco.com.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers
11
Ordering Documentation
Ordering Documentation
Cisco documentation and additional literature are available in a CD-ROM package, which ships with
your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated
monthly. Therefore, it might be more current than printed documentation. To order additional copies
of the Documentation CD-ROM, contact your local sales representative or call customer service.
The CD-ROM package is available as a single package or as an annual subscription. You can also
access Cisco documentation on the World Wide Web at http://www.cisco.com,
http://www-china.cisco.com, or http://www-europe.cisco.com.
If you are reading Cisco product documentation on the World Wide Web, you can submit comments
electronically. Click Feedback in the toolbar, select Documentation, and click Enter the feedback
form. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
This document is to be used in conjunction with the Cisco 2600 Series Hardware Installation Guide publication.
AccessPath, AtmDirector, the CCIE logo, CD-PAC, Centri, Centri Bronze, Centri Gold, Centri Security Manager, Centri Silver, the Cisco Capital logo, Cisco IOS, the Cisco IOS logo,
CiscoLink, the Cisco NetWorks logo, the Cisco Powered Network logo, the Cisco Press logo, ClickStart, ControlStream, Fast Step, FragmentFree, IGX, JumpStart, Kernel Proxy, LAN2LAN
Enterprise, LAN2LAN Remote Office, MGX, MICA, Natural Network Viewer, NetBeyond, NetRanger, NetSonar, Netsys Technologies, Packet, PIX, Point and Click Internetworking,
Policy Builder, RouteStream, Secure Script, SMARTnet, StrataSphere, StrataSphere BILLder, StrataSphere Connection Manager, StrataSphere Modeler, StrataSphere Optimizer, Stratm,
StreamView, SwitchProbe, The Cell, TrafficDirector, TransPath, VirtualStream, VlanDirector, Workgroup Director, Workgroup Stack, and XCI are trademarks; Empowering the Internet
Generation and The Network Works. No Excuses. are service marks; and BPX, Catalyst, Cisco, Cisco Systems, the Cisco Systems logo, EtherChannel, FastHub, FastPacket, ForeSight, IPX,
LightStream, OptiClass, Phase/IP, StrataCom, and StrataView Plus are registered trademarks of Cisco Systems, Inc. in the U.S. and certain other countries. All other trademarks mentioned
in this document are the property of their respective owners.
Copyright © 1998, Cisco Systems, Inc.
All rights reserved. Printed in USA.
9803R
12 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers