Cisco Systems 1130AG Network Router User Manual

A P P E N D I X
B
Declarations of Conformity and Regulatory
Information
This appendix provides declarations of conformity and regulatory information for the Cisco Aironet
1130AG Series Access Points and the Cisco Aironet 1130AG Series Lightweight Access Points.
This appendix contains the following sections:
•
Manufacturers Federal Communication Commission Declaration of Conformity Statement,
page B-2
•
Industry Canada, page B-4
•
European Community, Switzerland, Norway, Iceland, and Liechtenstein, page B-4
•
Declaration of Conformity for RF Exposure, page B-7
•
Guidelines for Operating Cisco Aironet Access Points in Japan, page B-8
•
Administrative Rules for Cisco Aironet Access Points in Taiwan, page B-9
•
Declaration of Conformity Statements, page B-11
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
B-1
Appendix B
Manufacturers Federal Communication Commission Declaration of Conformity Statement
Declarations of Conformity and Regulatory Information
Manufacturers Federal Communication Commission
Declaration of Conformity Statement
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Autonomous Access Point Models:
AIR-AP1131AG-A-K9
AIR-AP1131G-A-K9
Lightweight Access Point Models:
AIR-AP1131AG-A-K9
AIR-AP1131G-A-K9
AIR-LAP1131G-A-K9
FCC Certification numbers:
LDK102054
LDK102054E
LDK102065
Manufacturer:
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates,
uses, and radiates radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference. However, there is no guarantee that interference will not
occur. If this equipment does cause interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to correct the interference by one of the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-2
OL-8369-05
Appendix B
Declarations of Conformity and Regulatory Information
VCCI Statement for Japan
Caution
The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency when using the integrated antennas. Any changes or modification to the product not expressly
approved by Cisco could void the user’s authority to operate this device.
Caution
Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to
indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System
(MSS) operations.
Note
Dynamic Frequency Selection (DFS) operation and operation from 5500 to 5700 MHz has
not been authorized as required by the rules of the Federal Communications Commission
and is not supported until authorization is obtained.
VCCI Statement for Japan
Warning
This is a Class B product based on the standard of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a
domestic environment, it may cause radio interference. Install and use the equipment according to
the instruction manual.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
B-3
Appendix B
Declarations of Conformity and Regulatory Information
Industry Canada
Industry Canada
Models:
AIR-AP1131AG-A-K9 / AIR-AP1131G-A-K9
AIR-LAP1131AG-A-K9 / AIR-LAP1131G-A-K9
Certification number:
2461B-102054
Canadian Compliance Statement
This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du
Canada.
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two
conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired
operation.
Cisco Aironet 2.4-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread
spectrum devices, and Cisco Aironet 54-Mbps, 5-GHz Access Points are certified to the requirements of
RSS-210 for 5-GHz spread spectrum devices.The use of this device in a system operating either partially
or completely outdoors may require the user to obtain a license for the system according to the Canadian
regulations. For further information, contact your local Industry Canada office.
European Community, Switzerland, Norway, Iceland, and
Liechtenstein
Autonomous Access Point Models:
AIR-AP1131AG-E-K9
AIR-AP1131G-E-K9
Lightweight Access Point Models:
AIR-LAP1131AG-E-K9
AIR-LAP1131G-E-K9
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-4
OL-8369-05
Appendix B
Declarations of Conformity and Regulatory Information
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive)
This declaration is only valid for configurations (combinations of software, firmware, and hardware)
provided and supported by Cisco Systems. The use of software or firmware not provided and supported
by Cisco Systems may result in the equipment no longer being compliant with the regulatory
requirements.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
B-5
Appendix B
Declarations of Conformity and Regulatory Information
European Community, Switzerland, Norway, Iceland, and Liechtenstein
This device complies with the EMC requirements (EN 60601-1-2) of the Medical Directive 93/42/EEC.
For 2.4 GHz radios, the following standards were applied:
Note
•
Radio:
EN 300.328-1, EN 300.328-2
•
EMC:
EN 301.489-1, EN 301.489-17
•
Safety:
EN 60950
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to
certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate
Compliance.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-6
OL-8369-05
Appendix B
Declarations of Conformity and Regulatory Information
Declaration of Conformity for RF Exposure
For 54 Mbps, 5 GHz access points, the following standards were applied:
•
Radio:
EN 301.893
•
EMC:
EN 301.489-1, EN 301.489-17
•
Safety:
EN 60950
The following CE mark is affixed to the access point with a 2.4 GHz radio and a 54 Mbps, 5 GHz radio:
Declaration of Conformity for RF Exposure
The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and
15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating
Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The
equipment shoud be installed more than 20 cm (7.9 in.) from your body or nearby persons.
The access point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance
from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or
transmitters not approved by the FCC cannot be co-located with the access point. The access point’s
co-located 2.4 GHz and 5 GHz integrated antennas support a minimum separation distance of
8 cm (3.2 in.) and are compliant with the applicable FCC RF exposure limit when transmitting
simultaneously.
Note
Dual antennas used for diversity operation are not considered co-located.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
B-7
Appendix B
Declarations of Conformity and Regulatory Information
Guidelines for Operating Cisco Aironet Access Points in Japan
Guidelines for Operating Cisco Aironet Access Points in Japan
This section provides guidelines for avoiding interference when operating Cisco Aironet access points
in Japan. These guidelines are provided in both Japanese and English.
Autonomous Access Point Models:
AIR-AP1131AG-J-K9 / AIR-AP1131G-P-K9
Lightweight Access Point Models:
AIR-LAP1131AG-J-K9 / AIR-LAP1131G-P-K9
Japanese Translation
English Translation
This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices
such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio
stations and unlicensed specified low-power radio stations) used in factory production lines.
1.
Before using this equipment, make sure that no premises radio stations or specified low-power radio
stations of RF-ID are used in the vicinity.
2.
If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the
frequency or stop using the device; contact the number below and ask for recommendations on
avoiding radio interference, such as setting partitions.
3.
If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact
the number below.
Contact Number: 03-5549-6500
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-8
OL-8369-05
Appendix B
Declarations of Conformity and Regulatory Information
Administrative Rules for Cisco Aironet Access Points in Taiwan
Administrative Rules for Cisco Aironet Access Points in Taiwan
This section provides administrative rules for operatingCisco Aironet access points inTaiwan. The rules
are provided in both Chinese and English.
Access Points with IEEE 802.11a Radios
Chinese Translation
English Translation
This equipment is limited for indoor use.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
B-9
Appendix B
Declarations of Conformity and Regulatory Information
Administrative Rules for Cisco Aironet Access Points in Taiwan
All Access Points
Chinese Translation
English Translation
Administrative Rules for Low-power Radio-Frequency Devices
Article 12
For those low-power radio-frequency devices that have already received a type-approval, companies,
business units or users should not change its frequencies, increase its power or change its original
features and functions.
Article 14
The operation of the low-power radio-frequency devices is subject to the conditions that no harmful
interference is caused to aviation safety and authorized radio station; and if interference is caused, the
user must stop operating the device immediately and can't re-operate it until the harmful interference is
clear.
The authorized radio station means a radio-communication service operating in accordance with the
Communication Act.
The operation of the low-power radio-frequency devices is subject to the interference caused by the
operation of an authorized radio station, by another intentional or unintentional radiator, by industrial,
scientific and medical (ISM) equipment, or by an incidental radiator.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-10
OL-8369-05
Appendix B
Declarations of Conformity and Regulatory Information
Declaration of Conformity Statements
Declaration of Conformity Statements
All the Declaration of Conformity statements related to this product can be found at the following URL:
http://www.ciscofax.com
Declaration of Conformity Statements for European Union Countries
The Declaration of Conformity statement for the European Union countries is listed on the following
pages:
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
B-11
Appendix B
Declarations of Conformity and Regulatory Information
Declaration of Conformity Statements
DECLARATION OF CONFORMITY
with regard to the R&TTE Directive 1999/5/EC
according to EN 45014
Cisco Systems Inc.
170 West Tasman Drive
San Jose, CA 95134 USA
Declare under our sole responsibility that the product,
Product:
Variant:
AIR-AP1131AG-E-K9
AIR-LAP1131AG-E-K9
Cisco Aironet 1130AG Series IEEE802.11 a/b/g Access Point
Fulfils the essential requirements of the Directive 1999/5/EC
The following standards were applied:
EMC
EN 301.489-1 v1.4.1: 2002-08; EN 301.489-17 v1.2.1: 2002-09
Health & Safety EN60950: 2000; EN 50385: 2002
Radio
EN 301.893 v 1.2.3: 2003-08
EN 300 328 v 1.4.1: 2003-04
The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive
1999/5/EC has been followed.
The product carries the CE Mark:
Date & Place of Issue:
25 July 2005, San Jose
Signature:
Tony Youssef
Director Corporate Compliance
Cisco Systems, 125 West Tasman Drive
San Jose, CA 95134 - USA
DofC 441919rev1
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-12
OL-8369-05
Appendix B
Declarations of Conformity and Regulatory Information
Declaration of Conformity Statements
Annex to DofC# 441919
1.
Information on Antennas and Power Levels
The AIR-(L)AP1131AG-E-K9 has integral antennas. The antenna gain is 4 dBi (for both 2.4 GHz & 5 GHz).
The maximum (conducted) power level for operation in the 2.4 GHz band and the 5 GHz band mentioned are given
below and are based on a 100 mW eirp limit applicable in the 2.4 GHz band and a 200 mW eirp limit (5150-5350
MHz) or a 1 W eirp limit (5470-5725 MHz) applicable in the 5 GHz bands.
A separate compliance document shipped with each product will correctly inform the user on the applicable
maximum power level (eirp) in his area/country, the corresponding maximum setting for the conducted power and
other restrictions that might be applicable.
Any configuration resulting in an eirp level above the regulatory limit applicable in a given country is illegal and is
outside the scope of this Declaration.
Antenna P/N
Integral antenna 2.4 GHz
Integral antenna 5 GHz
Integral Ant. Gain
4 dBi
4 dBi
Max Power Level
15 dBm
17 dBm
July 25, 2005
Tony Youssef
Director Corporate Compliance
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
B-13
Appendix B
Declarations of Conformity and Regulatory Information
Declaration of Conformity Statements
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-14
OL-8369-05