Cisco Systems 15454-ML-4FC= Network Card User Manual

Installing Cisco ONS 15454 SONET/SDH
FC_MR-4 Cards
Product Name: 15454-ML-4FC=
This document lists regulatory requirements and describes installation procedures for the Cisco ONS
15454/ONS 15454 SDH FC_MR-4 card. It also contains removal instructions and technical
specifications. Use this document in conjunction with the Cisco ONS 15454 SDH Reference Manual, the
Cisco ONS 15454 SDH Procedure Guide, the Cisco ONS 15454 Reference Manual, and the Cisco ONS
15454 Procedure Guide.
This document contains the following sections:
•
“FC_MR-4 Card Description” section on page 1
•
“OC192 LR/STM64 LH ITU 15xx.xx Card-Level Indicators” section on page 5
•
“OC192 LR/STM64 LH ITU 15xx.xx Port-Level Indicators” section on page 5
•
“FC_MR-4 Card Specifications” section on page 3
•
“Installation Procedures” section on page 4
•
“Related Documentation” section on page 5
•
“Obtaining Documentation” section on page 10
•
“Obtaining Technical Assistance” section on page 12
This document contains the following procedures:
•
Procedure: Install the FC_MR-4 Card, page 5
•
Procedure: Verify Successful Turn Up of the OC192 LR/STM64 LH ITU 15xx.xx Card, page 9
FC_MR-4 Card Description
Warning
Class 1 (21 CFR 1040.10, 1040.11, and IEC 60825-1 2001-01) laser products. Invisible laser radiation may
be emitted from the end of the unterminated fiber cable or connector. Do not stare into the beam or
view directly with optical instruments. Viewing the laser output with certain optical instruments (for
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2003 Cisco Systems, Inc. All rights reserved.
FC_MR-4 Card Description
example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye
hazard. Use of controls or adjustments, or performance of procedures other than those specified may
result in hazardous radiation exposure.
The FC_MR-4 (Fibre Channel 4-port) card uses pluggable Gigabit Interface Converters (GBICs) to
transport non-SONET/SDH-framed, block-coded protocols over SONET/SDH in virtually concatenated
or contiguously concatenated payloads. The FC_MR-4 can transport Fibre Channel over SONET/SDH
using Fibre-Channel client interfaces and allows transport of one of the following at a time:
•
Two contiguously concatenated (CCAT) STS-24c/VC4-8c circuits
•
One STS-48c/VC4-16c CCAT
•
Two virtually concatenated (VCAT) circuits (STC3c-8V/VC4-8v) compliant with ITU-T G.7041
GFP-T and Telcordia GR-253-CORE
•
One STS-24c/VC4-8c CCAT and one STS-24c/VC4-8c VCAT
In Software Release 4.6, only two of the four ports can be active at one time.
Figure 0-1 shows the FC_MR-4 faceplate and block diagram.
Figure 0-1
FC_MR-4 Faceplate and Block Diagram
FC3_MR-4
FAIL
FLASH
ACT
SDRAM
MPC8250
Decode and
Control
PLD
GBIC
OPTICS
Rx
1
Tx
ACT/LNK
Rx
2
GBIC
OPTICS
GBIC
OPTICS
Tx
SERDES
RUDRA
FPGA
TADM
BTC
192
IBPIA
ACT/LNK
CDR +
SONET
FRAMER
GBIC
OPTICS
Rx
3
Tx
ACT/LNK
Rx
4
Tx
QDR MEMORY
ELAN
VCAT
PROCESSOR
IBPIA
B
A
C
K
P
L
A
N
E
DDR
MEMORY
110595
ACT/LNK
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
2
78-16233-01
FC_MR-4 Card Description
FC_MR-4 Card-Level Indicators
Table 0-1 describes the two card-level LEDs on the FC_MR-4 card.
Table 0-1
FC_MR-4 Card-Level Indicators
Card-Level Indicators
Description
Red FAIL LED
The red FAIL LED indicates that the card’s processor is not ready. Replace the
card if the red FAIL LED persists.
Green ACT LED
If the ACTV/STBY LED is green, the card is operational and ready to carry
traffic.
FC_MR-4 Port-Level Indicators
Each FC_MR-4 port has a corresponding ACT/LNK LED. The ACT/LNK LED is solid green if the port
is available to carry traffic, is provisioned as in-service, and in the active mode. The ACT/LNK LED is
flashing green if the port is carrying traffic. The ACT/LNK LED is steady amber if the port is not enabled
and the link is connected, or if the port is enabled and the link is connected but there is a SONET
transport error. The ACT/LNK LED is unlit if there is no link.
You can find the status of the card ports using the LCD screen on the ONS 15454 fan-tray assembly. Use
the LCD to view the status of any port or card slot; the screen displays the number and severity of alarms
for a given port or slot. Refer to the Cisco ONS 15454 Troubleshooting Guide for a complete description
of the alarm messages.
FC_MR-4 Card Specifications
The FC_MR-4 card has the following specifications:
•
Environmental
– Operating temperature
C-Temp (15454-E100T): –5 to +55 degrees Celsius (23 to 131 degrees Fahrenheit)
– Operating humidity: 5 to 95%, noncondensing
– Power consumption: 60 W, 1.35 A, 221.93 BTU/hr
•
Dimensions
– Height: 321.3 mm (12.650 in.)
– Width: 18.2 mm (0.716 in.)
– Depth: 228.6 mm (9.000 in.)
– Card weight: 1.17 kg (2.59 lb)
•
Compliance
– For compliance information, refer to the Cisco Optical Transport Products Safety and
Compliance Information.
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
78-16233-01
3
Installation Procedures
Installation Procedures
Use this section if you are installing the FC_MR-4 card for the first time. After you become familiar with
ONS 15454 SONET/SDH card installation and boot up, use this section as a reference. For information
about fiber optic cable installation, see the Cisco ONS 15454 SDH Reference Manual, the Cisco ONS
15454 SDH Procedure Guide, the Cisco ONS 15454 Reference Manual, or the Cisco ONS 15454
Procedure Guide.
Warning
Caution
Hazardous voltage or energy may be present on the backplane when the system is operating. Use
caution when servicing.
Always use the supplied electrostatic discharge (ESD) wristband when working with an ONS 15454
SONET/SDH. Plug the wristband cable into the ESD jack located on the lower right outside edge of the
shelf assembly and ensure the shelf assembly is properly grounded.
FC_MR-4 cards have electrical plugs that plug into electrical connectors on the shelf assembly
backplane. When the ejectors are fully closed, the card plugs into the shelf assembly backplane. Figure 2
shows general card installation. The example shows the installation in an ONS 15454. The procedure in
an ONS 15454 SDH is identical.
Figure 2
Installing a card in an ONS 15454
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
4
78-16233-01
Related Documentation
Procedure: Install the FC_MR-4 Card
Step 1
Open the card ejectors.
Step 2
Slide the card along the guide rails into the correct slot.
Step 3
Close the ejectors.
Procedure: Verify Turn Up of the FC_MR-4 Card
Follow the steps in this section to verify card turn up. If one or more of the Cisco Transport Controller
(CTC) software screen conditions according to this procedure are not met, reinstall the card. Replace the
unit if the faulty state persists.
Step 1
Verify that power is applied to the shelf assembly.
Step 2
Verify the LED activity:
•
The red FAIL LED turns on for 20 to 30 seconds. The ACT LED is amber for 3 to 5 seconds.
•
The red FAIL LED blinks for up to 2 minutes.
•
The FAIL and ACT LEDs blink once and turn off for 1 to 5 seconds.
•
The ACT LED turns on.
Note
If the red FAIL LED does not turn on, check the power.
Note
If you insert a card into a slot provisioned for a different card, all LEDs turn off.
Step 3
Verify that the ACT or ACT/STBY LED is on. The signal fail (SF) LED can persist until all card ports
connect to their far end counterparts and a signal is present.
Step 4
When you have displayed Cisco Transport Controller (CTC) on your workstation, verify that the card
appears in the correct slot on the CTC node view. See the Cisco ONS 15454 SDH Reference Manual, the
Cisco ONS 15454 SDH Procedure Guide, the Cisco ONS 15454 Reference Manual, or the Cisco ONS
15454 Procedure Guide.
Related Documentation
•
DOC-7815934= Cisco ONS 15454 Procedure Guide
•
DOC-7815981= Cisco ONS 15454 Reference Manual
•
DOC-7815982= Cisco ONS 15454 Troubleshooting Guide
•
DOC-7815983= Cisco ONS 15454 SDH Procedure Guide
•
DOC-7815988= Cisco ONS 15454 SDH Reference Manual
•
DOC-7815989= Cisco ONS 15454 SDH Troubleshooting Guide
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
78-16233-01
5
Obtaining Documentation
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation on the World Wide Web at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
International Cisco websites can be accessed from this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 800 553-NETS (6387).
Cisco Optical Networking Product Documentation CD-ROM
Optical networking-related documentation, including Cisco ONS 15454 product documentation, is
available in a CD-ROM package that ships with your product. The Optical Networking Product
Documentation CD-ROM is updated periodically and may be more current than printed documentation.
Documentation Feedback
You can submit e-mail comments about technical documentation to bug-doc@cisco.com.
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
6
78-16233-01
Obtaining Technical Assistance
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco
Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services,
online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for
technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.
Cisco TAC Website
The Cisco TAC website provides online documents and tools for troubleshooting and resolving technical
issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365
days a year. The Cisco TAC website is located at this URL:
http://www.cisco.com/tac
Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you
have a valid service contract but do not have a login ID or password, register at this URL:
http://tools.cisco.com/RPF/register/register.do
Opening a TAC Case
Using the online TAC Case Open Tool is the fastest way to open P3 and P4 cases. (P3 and P4 cases are
those in which your network is minimally impaired or for which you require product information.) After
you describe your situation, the TAC Case Open Tool automatically recommends resources for an
immediate solution. If your issue is not resolved using the recommended resources, your case will be
assigned to a Cisco TAC engineer. The online TAC Case Open Tool is located at this URL:
http://www.cisco.com/tac/caseopen
For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely
degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers
are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.
To open a case by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete listing of Cisco TAC contacts, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
78-16233-01
7
Obtaining Additional Publications and Information
TAC Case Priority Definitions
To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.
Priority 1 (P1)—Your network is “down” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Priority 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
Priority 3 (P3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Priority 4 (P4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Go
to this URL to visit the company store:
http://www.cisco.com/go/marketplace/
•
The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as
ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press online at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco quarterly publication that provides the latest networking trends,
technology breakthroughs, and Cisco products and solutions to help industry professionals get the
most from their networking investment. Included are networking deployment and troubleshooting
tips, configuration examples, customer case studies, tutorials and training, certification information,
and links to numerous in-depth online resources. You can access Packet magazine at this URL:
http://www.cisco.com/packet
•
iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet
business strategies for executives. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
8
78-16233-01
Obtaining Additional Publications and Information
•
Training—Cisco offers world-class networking training. Current offerings in network training are
listed at this URL:
http://www.cisco.com/en/US/learning/index.html
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
78-16233-01
9
Obtaining Additional Publications and Information
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards
10
78-16233-01