Cisco Systems 6503 Switch User Manual

CITIZEN
User's Manual
Model : CBM-270
Line Thermal Printer
Rev 1.00 Newly issued on 07.Oct.1998
Rev 2.00 Newly issued on 24.Nov.1998
Japan CBM Cor poration
Infor mation Systems Div.
CBM-270 User’s Manual
Declaration of Confor mity
Manufacturer’s Name :
Manufacturer’s Address
Declare the Product
Product Name
Model Number(s)
: Japan CBM Corporation
: CBM Bldg., 5-68-10, Nakano, Nakano-ku
Tokyo, 164-0001, Japan
Line Thermal Printer
CBM-270
(CBM-270R, CBM-270P)
(S.No.9880001 - )
Conform to the following Standards
LVD
: EN60950
EMC
: EN55022
: EN61000-3-2
: EN50082-1
: IEC801-2
: IEC801-3
: IEC801-4
: A4
: 1994 Class A
: 1995
: 1992
: 1991 4KV CD, 8KV AD
: 1984 3V/m, 26MHz-1000MHz AM1KHz 80%
: 1988 ±0.5KV Signal Line ±1KV AC mains
Supplementary Information
“The product complies with the requirements of the Low Voltage Directive 73/23/EEC,
93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC”
Place
Tokyo, Japan
Date
July.1998
Signature
Full Name : Mikio Moriya
Position : General Manager
R & D Department
Europe Contact :
Norco Declaration AB
Box 7146 S-250 07 Helsingborg Sweden
Warning
This is a Class A products. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
This declaration is applied only for 230V model.
2
CITIZEN
CBM-270 User’s Manual
IMPORTANT SAFETY INSTRUCTIONS
·Read all of these instructions and save them for future reference.
·Follow all warnings and instructions marked on the product.
·Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
·Do not use this product near water.
·Do not place this product on an unstable cart, stand or table. The product may fall, causing
serious damage to the product.
·Slots and openings on the back or bottom of the case are provided for ventilation. To ensure
reliable operation of the product and to protect it from overheating, do not block or cover
these openings. The openings should never be blocked by placing the product on a bed,
sofa, rug of other similar surface. This product should never be placed near or over a
radiator or heater. This product should not be placed in an built-in installation unless
proper ventilation is provided.
·This product should be operated from the type of power source indicated on the marking
label. If you re not sure of the type of power available, consult your dealer or local power
company.
·Do not allow anything to rest on the power cord. Do not place this product where the cord
will be walked on.
·If an extension cord is used with this product, make sure that the total of the ampere ratings
of the products plugged into the extension cord does not exceed the extension cord ampere
rating. Also, make sure that the total of all products plugged into the wall outlet does not
exceed 15 amperes.
·Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
·Except as explained elsewhere in this manual, do not attempt to service this product by
yourself. Opening and removing the covers that are marked “Do Not Remove” may expose
you to dangerous voltage points or other risks. Refer all servicing on those compartments
to service personnel.
·Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating instructions are followed.
Adjust only those controls that are covered be the operating instructions since improper
adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a need for service.
·Please keep the poly bag which this equipment is packed in away from children or throw it
away to prevent children from putting it on. Putting it on may cause suffocation.
3
CITIZEN
CBM-270 User’s Manual
WICHTIGE SICHERHEITSANWEISUNG
UNGEN
·Lesen Sie die nachfolgenden Anweisungen sorgfältig durch und bewahren Sie sie auf.
·Befolgen Sie alle auf dem Drucker vermerkten Hinweise und Anweisungen. Vor dem
Reinigen grundsätzlich Stecker aus der Steckdose ziehen. Keine Flüssigkeiten oder
Aerosolreiniger benutzen. Nut mit einem feuchten Tuch abwischen.
·Der Drucker darf nicht in der Nähe von Wasser aufgestellt werden.
·Drucker nicht auf einem unstabilen Wagen, Stand oder Tisch aufstellen. Der Drucker
könnte herunterfallen und dabel beschädigt werden.
·Schlitze und Öffnungen im Gehäuse, in der Rückwand und im Boden dienen der Belüftung.
Sie dürfen keinesfalls zugedeckt oder blockiert werden, da sich der Drucker sonst
überhitzt. Drucker nicht auf ein Bett, Sofa, Teppich oder dergleichen stellen. Drucker
nicht in der Nähe eines Heizkörpers aufstellen. Drucker darf nicht eingebaut werden,
falls nicht für ausreichende Belüftung gesorgt ist.
·Drucker nur mit der auf dem Typschild angegebenen Spannung betreiben. Wenn Sie sich
nicht sicher sind, fragen Sie ihren Händler oder ihr zuständiges Elektrizitätswerk.
·Nichts auf das Stromanschlußkabel stellen. Kabel muß so verlegt werden, daß man nicht
darauftreten kann.
·Ein etwaiges Verlängerungskabel muß der Stromstärke aller daran angeschlossenen Geräte
entsprechen.
·Keine Gegenstände in die Gehäuseschlitze schieben.
·Drucker darf nur da gewartet werden, wo im Handbuch angegeben, Öffnen und.
Abnehmen von Abdeckungen, die mit “Do not remove” gekennzeichenet sind, könnte
gefährliche spannungführende Stellen oder sonstige Gefahrenpunkte freilegen. Die
Wartung solcher Stellen darf grundsätzlich nur von besonders ausgebildetem
Fachpersonal vorgenommen werden.
A. Wenn das Stromanschlußkabel oder der Stecker beschädigt oder durch-gescheuert ist.
B. Wenn Flüssigkeit auf dem Drucker verschüttet wurde.
C. Wenn der Drucker im Regen gestanden hat oder Wasser darauf verschüttet wurde.
D. Wenn der Drucker trotz genauer Befolgung der Betriebsvorschriften nicht richtig
arbeitet. Nur die in der Bedienungsanleitung angegebenen Einstellungen vornehmen.
Ein Verstellen anderer Bedienungselemente könnte den Drucker beschädigen und
macht umständliche Arbeiten eines qualifizierten Technikers erforderlich, um den
Drucker Wieder auf den normalen Betrieb einzustellen.
E. Wenn der Drucker heruntergefallen ist oder das Gehäuse beschädigt wurde.
F. Wenn der Drucker in seiner Leistung nachläßt.
·Bitte halten Sie den Kunststoffbeutel, in den die Ware verpackt ist, von Kindern entfernt,
oder werfen Sie ihn weg, damit er nicht in die Hande von Kindern gerät. Das Überstülpen
des Beutels kann zum Ersticken führen.
Lär memissi
ssion kleiner 70d
70dBA
4
CITIZEN
CBM-270 User’s Manual
IMPORTANT:: This equipment generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instruction manual, may cause interference
to radio communications.
It has been tested and found to comply with the limits for a Class
A computing device pursuant to Subpart J of Part 15 off FCC Rules, which are designed to
provide reasonable protection against such interference when operated in a commercial
environment.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user at his own expense will be required to take whatever
measures may be necessary to correct the interference.
CAUTION: Use shielded cable for this equipment.
Sicherheitshinweis
Die Steckdose zum Anschluß dieses Druckers muß nahe dem Grät angebracht und leicht
zugänglich sein.
For Uses in Canada
This digital apparatus does not exceed the class A limits for radio noise emissions from digital,
apparatus, as set out in the radio interference regulations of the Canadian department of
communications.
Pour L’utilisateurs Canadiens
Cet appareil numérique ne dépasse pas les limites de carégorie a pour les émissions de bruit
radio émanant d’appareils numériques, tel que prévu dans les réglements sur l’interférence
radio du départment Canadien des communications.
5
CITIZEN
CBM-270 User’s Manual
<CAUTIONS>
1. Prior to using the equipment, be sure to read this User's Manual thoroughly. Please keep it handy
for reference whenever it may be needed.
2. The information contained herein may be changed without prior notice.
3. Reproduction of part or all of this User's Manual without permission is strictly prohibited.
4. Never service, disassemble, or repair parts that are not mentioned in this User's Manual.
5. Note that we will not be responsible for damages attributable to a user's incorrect operation/
handling or an improper operating environment.
6. Operate the equipment only as described in this User's Manual; otherwise accidents or problems
may result.
7. Data are basically temporary; they cannot be stored or saved permanently or for a long time.
Please note that we will not be responsible for damages or losses of profit resulting from losses of
the data attributable to accidents, repairs, tests, and so on.
8. If you have any questions or notice any clerical errors or omissions regarding the information in
this manual, please contact our office.
9. Please note that, notwithstanding Item 8 above, we will not be responsible for any effects resulting
from operation of the equipment.
6
CITIZEN
CBM-270 User’s Manual
SAFETY PRECAUTIONS ----- BE SURE TO OB
OBSERVE
In order to prevent hazards to an operator or other persons and damage to property, be sure to
observe the following precautions.
· The following describes the degrees of hazard and damages that can occur if the given
instructions are neglected or the equipment is incorrectly operated.
WARNING
Negligence of this precaution may result in death or serious
injury.
CAUTION
Negligence of this precaution may result in injury or damage to
property.
This is an illustration mark used to alert your attention.
This is an illustration mark used to indicate such information as an instruction or the like.
7
CITIZEN
CBM-270 User’s Manual
WARNING
· Never handle the equipment in the following manners, as it may break, become out of
order, or overheat causing smoke and resulting in fire or electric shock.
If the equipment is used in an abnormal condition, such as when broken, then problems,
smoke emission, abnormal odor/noise, and fire can result. If an abnormal condition exists,
be sure to disconnect the power plug from a plug socket, and contact our dealer. Never
repair the equipment on your own - it is very dangerous.
· Do not allow the equipment to receive a strong impact or shock, such as kicking, stomping,
hitting, dropping, and the like.
· Install the equipment in a well-ventilated place. Do not use it in such a manner that its
ventilation port will be blocked.
· Do not install the equipment in a place like a laboratory where chemical reactions are
expected, or in a place where salt or gases are contained in the air.
· Do not connect/disconnect a power cord or a data cable, while holding the cable. Do not
pull, install, use, or carry the equipment in such a manner that force will be applied to the
cables.
· Do not drop or insert any foreign substances, such as clips or pins, into the equipment.
· Do not spill any liquid or spray any chemical-containing liquid over the equipment. If any
liquid is spilled on it, turn off the power, disconnect the power cable and power cord from
the plug socket, and so on, and contact our dealer.
· Never disassemble or remodel the equipment. Negligence of this may cause fire or
electric shock.
· Use the equipment only with the specified commercial power supply and AC adapter.
Negligence of this may result in fire, electric shock, or problems.
· If you drop or break the AC adapter, or if water or the like gets inside it, unplug it
immediately from the socket and contact your dealer.
· Do not damage, break, process, bend/pull by force, twist, or head an AC adapter cord. Also,
do not put a heavy substance on it or heat it. The AC adapter cord could be broken,
resulting in fire, electric shock, or trouble. If the AC adapter cord is damaged, contact our
dealer.
· Do not connect/disconnect the AC adapter with wet hands.
· Do not overload a single electrical outlet, using a table tap or a current tap socket.
· An equipment packing bag must be discarded or kept away from children. A child can
suffocate if the bag is placed over the head.
8
CITIZEN
CBM-270 User’s Manual
PRECAUTIONS FOR INSTALLA
LLATION
· Do not use or store the equipment in a place exposed to fire, moisture, or direct sunshine,
or in a place near a heater or thermal device where the prescribed operating temperature
and humidity are not met, or in a place exposed to much oil, iron powder, or dust. The
equipment may become out of order, emit smoke, or catch fire.
· Do not install or use the equipment in a place like a laboratory where chemical reactions
are expected, or in a place where salt or gases are contained in the air. There is a danger
of fire or electric shock.
· Install the printer on a flat, stable desk or table that is free from vibration, in a wellventilated place.
· Do not install the printer at a location where its operation could be hindered.
· Do not place anything on the printer or leave small objects, like a clip or pin, around it. A
foreign object could cause trouble if it gets inside.
· Do not use any sharp-pointed object, such as a pen, for example, to touch the operation
panel of the printer. It could cause trouble.
· Do not use the equipment near a radio or TV receiver. Do not share the power from a plug
socket a radio or TV receiver is connected to. It may cause a reception problem.
· Use the equipment only at the specified power supply, voltage and frequency. Otherwise,
it may emit smoke and catch fire or cause other problems.
· Connect only the specified power source. Use of an unspecified power source could cause
trouble or smoke/fire.
· Confirm that a plug socket used for connection has sufficient capacity.
· Avoid connecting a power cable to a plug socket shared by other devices or extending the
wiring too far. It may result in the cable catching fire or a power outage. Also, do not
step on or apply an excessive force (Pull, load) to the cable, and do not use the printer with
such a force applied to it.
· Never connect a grounding cable (Frame ground) to a gas pipe. There is a danger of
explosion. When connecting or disconnecting the grounding cable, be sure to disconnect
the power cable and the power plug from the plug socket.
· When connecting/disconnecting the cables, be sure to turn off the power first, including the
connected side, and then connect/disconnect them, holding a plug and a connector.
Pulling the cable itself could cause it to snap or become damaged.
· Connect a power cable or a connector cable securely. If a reverse-polarity connection is
made, internal elements may be broken or a mating device may be adversely affected.
· Use a shielding wire or twisted pair wire for a signal line, in order to minimize noise effect.
Do not route the cable too long or connect it to a noisy device. Connection to a noisy device
could cause erroneous printing due to corrupt data, and so on.
· Use the equipment in an environment where there is a plug socket near the main body and
you can easily disconnect the power plug from it, to shut off the power.
· When the equipment will not be used for a long period of time, unplug it and remove the
paper roll from it.
· When transporting the equipment, remove the paper roll from the paper holder.
9
CITIZEN
CBM-270 User’s Manual
PREC
RECAUTIONS FOR HANDLING
Do not handle the equipment in the following manners, because problems may result.
· Do not use any other power source besides the accessory AC adapter. Also, do not use the
AC adapter for other purposes.
· Do not print without paper.
· Do not drop or put any foreign object, such as a clip, pin, or the like, inside the printer.
· Do not spill any liquid or spray any chemical-containing liquid over the equipment.
· Never use a pointed object, such as a pen, to operate the operation panel.
· Do not use Scotch tape to fasten paper together for continuous use.
It could damage the
printing head.
· Never pull the set paper forcibly. When opening/closing the printer cover, take care that
the paper will not be caught. It could cause the paper to jam.
· Be sure to use the specified paper.
Use of other paper could deteriorate the print quality
or cause a problem with the printing head.
To Prevent Injury and Spreading of Damage
· Never touch the printing head, motor, or paper cutting blade. Your finger may be cut.
· During power-on or immediately after printing, do not touch electrical parts or moving
parts, such as the mechanism, motor, internal gear, etc.
They may be very hot and can
burn your hand/finger.
· Be careful to avoid bodily injure or damaging other objects with an edge of sheet metal.
· Should any error occur while operating the equipment, stop it immediately and disconnect
the power plug from the plug socket.
· Only a qualified serviceman is allowed to disassemble or repair the printer.
· Should a problem occur, leave solving it to our serviceman.
Do not disassemble the
equipment on your own.
· When opening/closing the printer cover, and so on, be careful not to catch your hand or
finger on the equipment.
· After using the equipment, turn off the power switch and unplug the AC adapter from a
plug socket.
10
CITIZEN
CBM-270 User’s Manual
DAILY MAINTENANCE
· At the time of maintenance, be sure to turn off the power switch of the printer and unplug
it from the socket.
· Use a dry soft cloth to wipe off stains and dust from the surfaces of the main body case.
For severe soiling, dip the cloth in water and wring it, for wiping off the soil.
Never use
organic solvents, such as alcohol, thinner, trichlene, benzene, ketone, or chemical dusters.
· If the equipment is contaminated with paper powder, use a soft brush to clean it.
Be
careful not to damage the printing head.
CAUTION: The printing head and motor are very hot. Be careful not to touch them
immediately after printing.
Do not touch the heating surface of the head
with a bare hand or metal.
· Cleaning the Printing Head
1. Referring to "4.5 Removing Paper Jam," detach the platen roller unit.
2. Moisten gauze slightly with alcohol, and clean the heating surface of the printing head
with it.
3. Reattach the platen roller unit.
CAUTION: The printing head and motor are very hot. Be careful not to touch them
immediately after printing. Do not touch the heating surface of the head
with a bare hand or metal.
When detaching or reattaching the platen
roller unit, be sure to raise up the printing head; otherwise, they could be
damaged.
Handle the detached platen roller unit carefully so as not to
damage it.
11
CITIZEN
CBM-270 User’s Manual
CONTENTS
1. OUTLINE .............................................................................................................................................. 15
1.1 Features ................................................................................................................................................... 15
1.2 Unpacking................................................................................................................................................ 15
2. BASIC SPECIFICATIONS ................................................................................................................... 16
2.1 Model Classifications .............................................................................................................................. 16
2.2 Basic Specifications ................................................................................................................................. 17
2.3 Paper Specifications ................................................................................................................................ 18
2.3.1 Recommended Paper....................................................................................................................... 18
2.3.2 Printing Position ............................................................................................................................. 19
2.3.3 Head and Paper Cutter Layout ...................................................................................................... 19
3. OUTER APPEARANCE AND COMPONENT PARTS ....................................................................... 20
4. OPERATION ......................................................................................................................................... 22
4.1 Connecting AC Adapter........................................................................................................................... 22
4.2 Connecting Interface Cable .................................................................................................................... 23
4.3 Inserting the Paper ................................................................................................................................. 24
4.4 How to Remove Remaining Paper Roll................................................................................................... 25
4.5 Eliminating the Paper Jam..................................................................................................................... 26
4.6 FEED Switch Function ........................................................................................................................... 27
4.6.1 When Thermal Paper is Used ........................................................................................................ 27
4.6.2 When Label Paper is Used ............................................................................................................. 27
4.6.3 When the Macro is Executed.......................................................................................................... 27
4.6.4 When the Label is Fed to the Paper Cutting Position by the Command..................................... 27
4.7 Paper End Function ................................................................................................................................ 27
4.8 Paper Near End Function ....................................................................................................................... 28
4.9 Auto-Loading Function ........................................................................................................................... 29
4.10 Self-Print Function.................................................................................................................................. 29
4.11 Operation Panel and Display of Error................................................................................................... 30
4.12 Red/Black Print (Precations for use) ...................................................................................................... 31
5. DIP SWITCH SETTING ....................................................................................................................... 32
5.1 Location of DIP Switch ........................................................................................................................... 32
5.2 DIP Switch Function ............................................................................................................................... 32
5.3 Jumper Wire Function ............................................................................................................................ 33
12
CITIZEN
CBM-270 User’s Manual
6. PARALLEL INTERFACE ..................................................................................................................... 34
6.1 Specifications ........................................................................................................................................... 34
6.2 Connector's Pin Configuration ............................................................................................................... 34
6.3 Input and Output Signals....................................................................................................................... 35
6.3.1 Input and Output Signals............................................................................................................... 35
6.3.2 Electrical Characteristics ............................................................................................................... 36
6.3.3 Timing Chart ................................................................................................................................... 37
6.3.4 Data Receiving Control ................................................................................................................... 37
6.3.5 Buffering .......................................................................................................................................... 37
7. SERIAL INTERFACE ........................................................................................................................... 38
7.1 Specifications ........................................................................................................................................... 38
7.2 Connector's Pin Configuration ............................................................................................................... 38
7.3 Input and Output Signals....................................................................................................................... 39
7.3.1 Input and Output Signals............................................................................................................... 39
7.3.2 Data Configuration ......................................................................................................................... 40
7.3.3 Error Detection ............................................................................................................................... 40
7.3.4 Data Receiving Control ................................................................................................................... 41
7.3.5 Buffering .......................................................................................................................................... 41
7.3.6 Electrical Characteristics ............................................................................................................... 41
8. POWER CONNECTOR......................................................................................................................... 42
9. MAINTENANCE AND SERVICE........................................................................................................ 43
10. PRINT CONTROL FUNCTIONS......................................................................................................... 44
10.1 Command List ......................................................................................................................................... 44
10.2 Command Details .................................................................................................................................... 46
10.2.1 Descriptions of Each Items ............................................................................................................ 46
10.2.2 Command Details............................................................................................................................ 47
11. CHARACTER CODES TABLE............................................................................................................. 88
11.1 International............................................................................................................................................ 88
11.2 Domestic................................................................................................................................................... 88
11.3 International Character Codes Table .................................................................................................... 89
13
CITIZEN
CBM-270 User’s Manual
APPENDIX 1. BLOCK DIAGRAM .......................................................................................................... 90
APPENDIX 2. DRAWING ........................................................................................................................ 91
APPENDIX 3. WALL MOUNTING HOLES LAYOUT DRAWING ...................................................... 92
<<< Ger man >>>
>>>
4. BETRIEB ............................................................................................................................................. 100
4.1 Anschließen des Netzteils ..................................................................................................................... 100
4.2 Anschließen des Schnittstellenkabels.................................................................................................. 101
4.3 Einsetzen des Papiers ........................................................................................................................... 102
4.4 Entnehmen der eingesetzten Papierrolle ............................................................................................ 103
4.5 Beheben von Papierstau ....................................................................................................................... 104
4.6 FEED-Schalterfunktion ........................................................................................................................ 104
4.6.1 Bei Verwendung von Thermalpapier ........................................................................................... 104
4.6.2 Bei Verwendung von Etikettenpapier.......................................................................................... 104
4.6.3 Bei Ausführung eines Makros ...................................................................................................... 104
4.6.4 Wenn das Etikett mit Befehl bis zur Papierschneideposition vorgeschoben wird.................... 104
4.7 Papierende-Funktion ............................................................................................................................ 105
4.8 Papiermangel-Funktion........................................................................................................................ 105
4.9 Autoladefunktion................................................................................................................................... 107
4.10 Selbstdruckfunktion.............................................................................................................................. 107
4.11 Bedienfeld und Fehleranzeigen............................................................................................................ 108
4.12 Rot/Schwalts-Druck(Vorsichtsmaßregeln):...........................................................................................110
5. DIP-SCHALTEREINSTELLUNG...................................................................................................... 111
5.1 Lage der DIP-Schalter ...........................................................................................................................111
5.2 DIP-Schalterfunktion.............................................................................................................................111
5.3 Jumperdraht-Funktion ..........................................................................................................................111
9. WARTUNG UND DIENST ................................................................................................................. 113
14
CITIZEN
CBM-270 User’s Manual
1.
OUTLI
TLINE
This small line thermal printer is designed for various types of data communication terminals
and measuring instrument terminals.
Its abundant built-in features allow you to widely use
this printer for different applications.
Prior to using it, read and understand this manual
thoroughly.
1 .1
Features
1.
Small, lightweight, and installable in a narrow area
2.
High speed and low noise, owing to line thermal print
3.
Long-life printing head and high reliability, owing to the simple mechanism
4.
Easy paper-loading, owing to the auto-loading function
5.
Built-in input buffer
6.
Capable of printing a bar code (Special command)
7.
Capable of accommodating both thermal paper and label paper
8.
A little discharge (1 sheet) of the label paper at power-on or paper replacement
9. Capable of printing in two colors (when special paper is used)
10. External characters registration function(94 kanji characters, 95 ANK characters)
1 .2
Unpacking
When unpacking the package, confirm that the following parts are provided:
·Printer body
-----1 unit
·Sample paper roll
-----1 roll
·AC adapter
-----1 piece
·AC cord
-----1 piece
·User's manual
----- 1 copy
CAUTION
· Install the printer body on a flat and stable desk or mount it onto the wall, etc., using a hook,
etc.
· Do not install the printer near a heater or in a place exposed to the direct sunshine.
· Do not use the printer in a high-temperature, high-humidity, or contaminated environment.
· Do not allow dew condensation to form on the printer.
If such condensation should form, do
not turn on the power until it has completely gone away.
· Use only the accessory AC adapter. Do not use it for any other purpose.
· If you do not use the printer for a long period, disconnect the power cable from the socket.
· Keep this manual carefully at hand for ready reference.
15
CITIZEN
CBM-270 User’s Manual
2.
2 .1
BAS
BASIC SPECI
ECIFICATIONS
Model Classi
ssifications
The models are classified by the following designation method:
CBM-270
-
R
F
120
-
N
Label Paper Print Function
Model Name
N: None
CBM-270: Standard Model
L : Label interval detection
M: Black mark detection
AC Power Cord
120: 120 V AC
230: 230 V AC
International Characters
F: International
Interface
R: Serial (RS-232C)
P: Parallel
(CENTRONICS Compliant)
* Special Switching Power Source and Power Cord
Switching power source : 27AD (Input: 100 to 240V AC)
Power cord
: 100V AC --- 2-core cord
120V AC --- 2-core cord
230V AC --- 2-core cord
Cord length
: Power cord(For AC Input)
--- Approx. 1.8 m
Secondary side (For DC Output) --- Approx. 1.8 m
16
CITIZEN
CBM-270 User’s Manual
2.2
Basic Specifications
Item
Printing system
Printing width
Dot density
Paper feed pitch
Printing speed
Printing columns
character size
Line interval
Model
and
Character types
Character code
Bar code type
Paper
(See Paper Specifications)
Interface
Input buffer
Download characters
Auto-loading
Paper end function
Paper near end function
Label detecting function
Printing color
AC adapter
Type
AC cord
Supply voltage
Power consumption
Weight
Outer dimensions
Operating
temperature
and humidity
Storage temperature and
humidity
Reliability
EMI
*1
Applicable standard (Main
body)
*1
Applicable
standard
(Power source)
CBM-270-RF120-*
CBM-270-RF230-*
CBM-270-PF120-*
CBM-270-PF230-*
Line thermal dot printing
48 mm (384 dots/line)
8 dots/mm (Width, Length)
0.125 mm
Approx. 11 lines/sec. (At maximum)
32 columns (12 ´ 24 Font A) 1.25 ´ 3.00 mm
42 columns (9 ´ 24 Font B) 0.88 ´ 3.00 mm
Initial value: 4.23 mm (1/6 inch)
Can be set with a command (1/360 inch at minimum)
Alphanumerals, symbols, international characters
(Choose from 10 countries)
Domestic characters, IBM characters #2 (Choose either)
UPC-A/E, JAN(EAN) 13-/8-column, ITF, CODE 39, CODE 128, CODABAR
Thermal paper roll : 58 + 0/- 1 mm xf83 (max.) mm, 60~75mm thick
Thermal label paper : 58 + 0/- 1 mm xf83 (max.), 150mm thick (max.)
(L and M Spec. only) Label width: 56 mm (max.)
Label length: 25 mm/sh. (min.)
Serial (RS-232C), Parallel (CENTRONICS compliant)
2 KB
Font A, B: 95 characters each
Provided (Can be enabled/disabled with the DIP switch)
Provided
Provided (Can be enabled/disabled with the DIP switch)
Capable of selecting label interval detection, black mark detection, or none.
Capable of printing in two colors (red/black) with the special thermal paper.
Rated input : 100~240 V, 50/60 Hz, 40 VA
Rated output : 7.2 V DC, 2 A
27 AD
2-core cord (Depends on the destination)
120 V AC +/- 10%, 60 Hz
230 V AC +/- 10%, 50/60 Hz
At non-printing: Approx. 2 W
At printing: Approx. 15 W (approx. 20 W at maximum)
Main body: Approx. 600 g (Paper roll excluded)
AC adapter: Approx. 350 g
106 (W) ´ 184 (D) ´ 110 (H) mm
5~40°C, 35~85 % RH (No dew condensation)
-20~60°C, 10~90% RH (No dew condensation)
Printing head life: (25°C)
Pulse resistance : 50 million pulses or more (Print rate 12.5%)
Wear resistance : 50 km or more (With recommended thermal paper at
normal temperature and humidity)
FCC Class-A
EN55022 Class-A
GS, CE Marking
UL, C-UL
GS
* *1 indicates the standard satisfied when the AC adapter 27AD is used.
* GS and CE Marking are satisfied when the main body and AC adapter are combined.
17
CITIZEN
CBM-270 User’s Manual
2.3 Paper Specifications
2.3.1
Recomme
mmended Paper
(1) Thermal paper roll
·Type
: Thermal paper
·Paper width
: 58 + 0/- 1 mm
·Paper thickness
: 60~75mm
·Roll diameter
: f83 mm or less
·Printing surface
: Outside of the roll (Surface)
·Recommended paper
: TF50KS-E2C (Monochrome) made by NIPPON SEISHI or its
equivalent
735FA(2-color, Black based) made by RICOH or its equivalent
PB670(2-color, Red based) made by MITSUBISHI SEISHI or its
equivalent
·Core
:f12 mm(Inner dia.), f18 mm (Outer dia.)
(2) Thermal label paper(L and M spec. only)
·Type
: Thermal paper (Printing surface)
·Paper width
: 58 + 0/- 1 mm
·Label width
: 56 mm or less
·Label length
: 25~300 mm (For label interval detection)
25~300 mm (For black mark detection) * Black mark section excluded
·Label interval
: 3~300 mm (Black mark interval for the black mark detection)
·Black mark width
: 15 mm or more (From the center of the paper, black paper only)
·Paper thickness
: 150mm or less
·Roll diameter
: f83 mm or less (Depends on the outer diameter of the core)
·Printing surface
: Outside of the roll (Surface)
·Recommended paper
: For label interval detection
KPT86S P22 G63BC (Monochrome) made by OHJI TUCK or
its equivalent
For black mark detection
KPT865P (Monochrome) made by OHJI TUCK or its equivalent
·Core
: f12 mm or more (Inner dia.), 3 mm thick
CAUTION:
1. Use of non-specified paper may cause irregularity of print density. If this is the case, use the
DIP switch to reset print density. (See 5. DIP SWITCH SETTING)
2. Do not paste the paper to the core.
3. If the paper comes in contact with a chemical or oil, it may discolor or lose a record.
4. Do not rub the paper surface strongly with a nail or hard metal. It may discolor.
5. Discoloring starts at about 70°C. Watch out for effects of heat, humidity, light, and so on.
6. Do not use the label paper when the printer has been set for thermal paper, and vice versa.
Be careful not to mistake a type of label paper. It could cause malfunctioning or damage the
printing head.
18
CITIZEN
CBM-270 User’s Manual
2.3.2
Printing Position
(1) Thermal paper
(2) Label paper (For label interval detection) * L spec. only
(3) Label paper (For black mark detection) * M spec. only
2.3.3
Head and Paper Cutte
tter Layout
19
CITIZEN
CBM-270 User’s Manual
3.
OUTER AP
APPEARA
ARANCE AN
AND COMPONENT PARTS
Printer Cover
Upper Cover
Bottom Cover
POWER Switch
POWER Lamp
ERROR Lamp
PAPER Lamp
FEED Switch
DIP Switch
PNE Sensor
Paper Holder
Label Detection Sensor
(L and M spec. Only)
Printer Mechanism
Paper Cutter
Head-up Lever
Platen Roller Unit
Interface Connector
Power Connector
20
CITIZEN
CBM-270 User’s Manual
(1) POWER switch
Turns on/off the power for the printer body.
(2) POWER lamp
Illuminated when the power switch is turned on.
(3) ERROR lamp
Illuminated at the time of a head-up mechanical error, and blinks at the time of starting a
macro.
(4) PAPER lamp
Illuminated when the paper is running out (when there is little paper left), and blinks when
a label paper cut is specified.
(5) FEED switch
Feeds the paper. It is fed continuously while the switch is held down. For the label paper,
it is fed by one label.
(6) Paper holder
Set the paper roll in this holder.
(7) PNE sensor
Detects that the paper is running out.
(8) DIP switch
Initially sets the printer at power-on and sets the functions.
(9) Label detection sensor (L and M spec. only)
Detects the labels. Deals with either the label interval or black mark.
(10) Platen roller unit
Detach this unit when the paper is jamming or when you clean the head.
(11) Head-up lever
Used when replacing the paper or detaching/reattaching the platen roller unit.
(12) Paper cutter
Cuts the printed paper.
(13) Power connector
Connects to the accessory AC adapter (27AD).
(14) Interface connector
Connects to a communication interface cable.
There are two types, for serial and parallel
interfaces.
(15) Printer cover
Detach this cover when replacing the paper.
21
CITIZEN
CBM-270 User’s Manual
4.
4 .1
OPERA
ERATION
Conne
nnecting AC Adapter
1. Turn off the power.
2. Connect the cable connector of the AC adapter to the power connector located on the back of
the printer.
3. Connect the AC power cord of the AC adapter, and plug it into a socket.
CAUTION:
1) Use only the specified AC adapter.
2) When disconnecting/reconnecting the cable connector of the AC adapter, be sure to hold the
connector.
3) Separate the AC adapter from other noise-generating devices.
4) Pulling the AC power cord may damage it, resulting in a fire, electric shock, or snapping.
5) If a thunder/lightning storm is nearby, disconnect the AC adapter from the socket and do not
use the printer, because a fire or electric shock may occur.
6) Do not put the AC power cord close to a heating device.
Its coating can melt and cause a fire
or electric shock.
7) Install the printer in a well-ventilated place, because the AC adapter generates heat when it is
used.
8) Use the specified AC power source.
Connect to a power source with sufficient capacity. If
the capacity is insufficient, a fire may result from heat generation.
9) After using the printer or when not using it for a long period of time, be sure to unplug the AC
adapter from a plug socket for your safety.
22
CITIZEN
CBM-270 User’s Manual
4 .2
Conne
nnecting Interface Cable
1. Turn off the power. (Mating side included)
2. Check the top and bottom of cable terminals, and connect to the interface connector.
3. Fix the cable terminals.
Serial interface
: Tighten screws, to fix it.
Parallel interface
: Turn a stopper, to fix it.
4. Connect the cable to the host computer.
CAUTION:
1) Referring to "6. PARALLEL INTERFACE" and "7. SERIAL INTERFACE," check the pin
configuration of the interface connector and cable.
Wrong wiring could cause trouble or
malfunctioning to not only the printer body but also the host computer.
2) When disconnecting/reconnecting the interface cable, be sure to hold the connector.
Pulling
the cable itself may snap the internal wires.
3) Connect the interface cable securely. Otherwise, communications may not be obtained due to
a connection failure.
23
CITIZEN
CBM-270 User’s Manual
4 .3
Inserting the Paper
CAUTION:
1) Be sure to use the specified paper roll.
2) Use of non-specified paper may not guarantee the print quality, printing head life, and so on.
3) Do not use thermal paper when the printer has been set for label paper, and vice versa.
It
could cause malfunctioning of the printer or damage the printing head.
1. Hold the convexity on the rear of the printer cover, and raise it upward.
2. Cut the front end of the paper roll almost at a right angle.
CAUTION:
1) The printer cover is not stationary (Opening/Closing).
After detaching it, be careful not to
lose or break it.
2) Do not insert a ragged or dog-eared end of the paper roll, because it could result in a paper jam
or insertion error.
3. Make sure that the power is turned on.
4. Pull the head-up lever to this side to raise up the printing head.
5. If there is still some paper remaining after a paper-out indication, eliminate the paper roll
according to "4.4 How to Remove the Remaining Roll Paper."
6. Insert the front end of the paper roll straight into a paper insertion slot.
7. Set the paper roll firmly in the paper holder.
8. Put back the head-up lever. The paper roll is automatically pulled in by the platen roller to
feed a constant amount of paper. (When auto-loading is enabled.) (For the label paper, it is
fed to the print start position of the 2nd sheet.)
9. Put back the printer cover.
CAUTION:
1) If the paper roll is still slack, rewind the paper to remove the slack.
2) If the paper roll is tilted, raise the head-up lever to correct the paper roll position, or pull out
the paper roll and set it again.
3) Do not open the printer cover while printing.
4) Do not hold or press the paper roll while printing, because it could cause a paper jam.
24
CITIZEN
CBM-270 User’s Manual
5) After the paper is set, the printer is made ready to start printing. Note that if data is
remaining in the buffer, the printer will start printing after the paper is set.
6) Do not run the printer with its cover removed, because it could cause malfunctioning or an
irregularity of the sensor.
4 .4
How to Remove Remaining Paper Roll
1. Remove the printer cover.
2. Raise the head-up lever.
3. Gently pull out the paper to the near side.
If the paper roll is still remaining, cut it just
before the paper insertion slot before pulling it out.
CAUTION:
1) Do not pull out the paper roll in the opposite direction.
2) If you do so with the label paper, the labels may come off.
3) Never take out paper with the head-up lever lowered, because it could damage the printing
head.
4) The printer mechanism may be very hot just after printing, so be duly careful.
25
CITIZEN
CBM-270 User’s Manual
4 .5
Elim
liminating the Paper Jam
1. Turn off the power.
2. Detach the printer cover.
3. Cut the paper roll near the paper insertion slot.
4. Raise the head-up lever.
5. Raise the blue levers located on both sides of the platen roller unit, to gently detach the unit.
The platen roller unit can be detached by manually raising the blue levers.
6. Remove the remaining paper roll completely from the paper passage.
7. If the label paper is used, some paste may be adhered.
Dip soft cloth, etc. in alcohol and
wipe away the paste carefully so as not to damage the printing head.
8. Confirming the direction of the platen roller unit, reattach it to the mechanism.
Shift
down the blue levers on both sides, to fix the unit.
9. Lower the head-up lever.
CAUTION:
1) Do not carry out this work just after printing because the printing head is very hot.
2) Be sure to turn off the power when detaching the platen roller unit.
3) When eliminating remaining paper, do not touch the heating surface of the head with a bare
hand or metal piece.
4) Do not detach the platen roller unit unless necessary, such as for a paper jam.
5) When putting back the platen roller unit, be sure to confirm that it is correctly reattached.
6) Never detach or reattach the platen roller unit with the head-up lever lowered.
26
CITIZEN
CBM-270 User’s Manual
4 .6
FEED Switch Function
4.6.1
When Ther mal Paper is Used
Pressing the switch, feed the paper by 1 line.
If the switch is held down, the paper will be
fed continuously.
4.6.2
When Label Paper is Used
Pressing the switch, feed the paper by 1 line. If the switch is held down for 1 second or more,
the paper will be fed by one label.
4.6.3
When the Macro is Executed
If the ERROR lamp is blinking while waiting for execution of a macro, press the FEED
switch. The waiting state continues until the switch is pressed.
4.6.4
When the Label is
is Fed to the Paper Cutti
tting Position by the Comma
mmand
The PAPER lamp blinks. After cutting the paper, pressing the FEED switch searches for the
head of the next label. The waiting state continues until the switch is pressed.
CAUTION:
If the label paper is fed by 1 line by pressing the FEED switch, the label head position will be
dislocated.
Note that if printing starts in this state, the label will be printed dislocated. (It is
recommended to feed the paper by 1 label.)
4 .7
Paper End Function
If the printing paper runs out, the parallel interface will output BUSY, FAULT, and PE to the
host, and the serial interface will output DTR to stop printing, respectively.
If some data are
still remaining in the buffer, printing will be resumed after replacing the paper.
Replace the
paper according to "4.3 Inserting the Paper." After replacing the paper, cancel BUSY (DTR),
FAULT, and PE outputs. For details, see "4.8 Near Paper End Function."
27
CITIZEN
CBM-270 User’s Manual
4 .8
Paper Near End Function
If the paper is running out, the PNE sensor informs the host computer that the paper is
running out, by means of a signal output or the PAPER lamp on the panel. The PAPER lamp
is illuminated unconditionally.
1. If the PNE sensor detects that the paper is running out, the PAPER lamp will be
illuminated.
2. If PNE is enabled, the parallel interface will output PE. (At initial setting)
3. Printing is allowed up to about 1.5 m. (Initial value) After printing or feeding the paper by
a specified amount, the parallel interface will output BUSY and FAULT, and serial interface
will output DTR to stop printing, respectively.
4. Replace the paper according to the procedure in "4.3 Inserting the Paper."
5. After replacing the paper, cancel the BUSY (DTR), FAULT, and PE outputs.
(1) The following lists the outputs made by the near paper end function and the paper end
function. The output state can be changed by the DIP switch or a command.
DS1-1
PNE
State Function
OFF
Disabled
ON
Enabled
PE Signal Output
Setting by Command
*When PE is selected
When PNE is selected
When PE is selected
BUSY (DTR)/
PAPER
FAULT Output
Lamp
*When PE is detected
*When PE is detected *At PNE
When PNE is detected
When PE is detected
At PNE
When PE is detected
When printing stops At PNE
due to PNE
*When PNE is selected *When
PNE
is *When printing stops *At PNE
detected
due to PNE
PE Output
*Mark : Default setting
PNE : Paper Near End
PE : Paper End
(2) Print amount after detecting PNE
When PNE is enabled, a printable amount after PNE detection can be adjusted.
PNE is
detected when the remaining amount of the paper roll is about 2~3 m. (It depends on the
paper quality used, paper thickness, and operating environment.)
An initial value is 1.5 m. Up to 1.5 m can be printed after detecting PNE. At this time,
with the approx. 70mm-thick recommended paper, the remaining amount of the paper will
be about 0.5~1.5 m when printing stops.
It can be adjusted between 0 and 2.55 m with a command.
Adjust it depending on the
operating environment and paper quality.
Depending on an adjustment value, paper end may be detected (Printing stop) first.
If PNE is detected at power-on, a set amount of printing will be done from that point.
(The default is 1.5 m)
28
CITIZEN
CBM-270 User’s Manual
4 .9
Auto-Loading Function
This printer has a function to automatically set the paper.
If the paper end sensor, near
paper end sensor, and head-up lever are cancelled, the paper will be automatically fed by a
constant amount in about 1 second. (Up to the print start position of the second sheet in the
case of label paper.)
In order to smooth operation, cancel the head-up mechanism last.
Also, you can use the DIP switch to enable/disable the function. If disabled, auto-loading will
not be performed. (The paper is fed to the print start position in the case of label paper.)
CAUTION:
1) When auto-loading is being activated, do not touch the paper roll, because it could result in a
paper feed failure or cause the paper to be one-sided.
2) Be sure to set the paper until it comes into contact with the platen roller; otherwise, the paper
cannot be fed and the printing head could be damaged.
3) In the case of label paper, if the label section or black mark (Between the labels) cannot be
detected in feeding the paper by a constant amount, the printer will illuminate the ERROR
lamp and stop operation, regarding it as a paper error.
4.10 Self-P
f-Print Function
This printer has a function to perform preset printing. Turn on the power with the FEED
switch held down. It will print the ROM version, DIP switch state, characters used, kanji, etc.
After self-printing is completed, the printer restores its normal operating conditions.
In the case of label paper, it is fed to the print start position of the next label.
CAUTION:
1) Do not use this function when the paper roll is running out.
2) If the label length is short in printing on label paper, printing will extend over several labels.
3) Data communication cannot be done during self-printing.
4) The print contents differ between thermal paper and label paper.
29
CITIZEN
CBM-270 User’s Manual
4.11
Operation Panel and Display of Er ror
1. POWER lamp (Green)
Illuminated if the power is turned on.
2. ERROR lamp (Red), PAPER lamp (Red)
Indicates an error by illuminating or blinking the lamps.
Error
Memory check error
Display
ERROR Lamp
PAPER Lamp
Reset
Quick blinking
ON
OFF
Cannot be reset
OFF
Head overheat
ON
OFF
Paper near end
OFF
ON
Paper end
OFF
ON
Lower the head-up lever.
Automatically reset by a
temperature drop
Set a new paper roll after a
print stop.
Set a new paper roll.
OFF
Press the FEED switch.
Head-up
Macro execution wait
Slow blinking
Label paper cut wait
OFF
Label paper error
ON
Slow blinking
ON
Press the FEED switch.
Set the label paper suitable
for the specifications.
<Er ror Details
ils>
Head-up
----- Occurs when the head-up lever is raised. The printer cannot feed the
paper or print. The parallel interface outputs BUSY and FAULT, and
serial interface DTR, respectively.
Head overheat
----- If the temperature of the printing head rises (About 60°C or more), in
order to protect it against overheating, a printing head temperature
sensor will be activated to stop printing. The parallel interface outputs
BUSY and FAULT, and serial interface DTR, respectively. If the
temperature drops (About 55°C), printing will be automatically resumed.
Paper near end
----- If the diameter of the paper roll decreases, the paper near end sensor will
react to inform you that the paper roll is running out. See "4.8 Paper
Near End Function".
Paper end
----- If the paper roll runs out, the paper sensor near the printing head will
react to stop printing. See "4.7 Paper End Function".
Label paper error ----- Occurs if you set the thermal paper or non-specified label paper, when the
label paper has been selected. The parallel interface outputs BUSY and
FAULT, and serial interface DTR, respectively.
3. FEED switch
See "4.6 FEED Switch Function."
30
CITIZEN
CBM-270 User’s Manual
4.12 Red/Black Print (Precautions for Use)
(1) Types of paper
The red and black two-color thermal paper changes its colors by controlling the energy
applied to the thermal head.
It is largely divided into two types, depending on the color
development order. Select either of them to suit your application.
1. Red-based two-color thermal paper (PB670: MITSUBISHI PAPER MILLS)
Red print (low energy)
®
Black print (high energy)
2. Black-based two-color thermal paper (735FA: RICOH)
Black print (low energy) ®
Red print (high energy)
(2) High-energy printing rate
High-energy print (black print on red-based paper, or red print on black-based paper)
required the application of high energy to the thermal head. To protect the service life of
the thermal head, use the following printing rate as a guideline; use the fixed split (6-split)
method.
1. Continuous print of high-energy print only : 6 % or less
2. Mixed continuous print of low-energy and high-energy print
: 30 % or less of the standard printing rate
of 12.5 %
3. Printing rate per dot line
: 50 % or less
(3) Minimum dots for high-energy print
When high-energy print is used, the recommended minimum area is 3 dots (length) ´ 3
dots (width) or more.
Depending on the set printing density, the paper used, or the
printing characters, a sufficient change of color tone may not be obtained even by highenergy print.
(Characters such as [, !, ', (, i, -, font B with small dot matrix)
It is recommended to use in such printing patterns as double-width characters, doubleheight characters, double-width and -height characters.
CAUTIONS
1) If high-energy print is continuously carried out at a high operating ambient temperature, the
thermal head will become hot more quickly and the protective circuit will be activated, to stop
printing more frequently.
Fully consider the working temperature and printing rate.
2) If a bar code is printed on the 2-color paper, both colors may appear in normal print and highenergy print, or the bar code may not be correctly read by a bar code reader. Be fully aware of
this when using the 2-color paper.
3) Do not perform high-energy print on the single-color paper (regular thermal paper). It may
deteriorate the service life of the thermal head or the printing quality.
4) For setting, see Commands (DC3: Switching the Red/Black Printing).
31
CITIZEN
CBM-270 User’s Manual
5.
5 .1
DIP SWITCH SETTING
Location of DIP Switch
1. Turn off the power.
2. Detach the printer cover, and take out the paper roll. (The switch is found under the paper roll.)
3. There are 2 switches (8-pole and 4-pole) for the serial interface, and 1 switch (8-pole) for the
parallel interface.
5 .2
DIP Switch Function
DS1
No.
1
2
3
4
5
6
7
8
Function
PNE selection
CR switching
ON
Enabled
LF operation
Print density
OFF
Disabled
Ignored
See Table 1
Paper selection
Auto-loading
DTR/DSR, XON/XOFF
Kanji code selection
Label paper
Enabled
XON/XOFF
S-JIS
Thermal paper
Disabled
DTR/DSR
JIS
Upon Shipment
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
* DS1-7: Enabled only for the serial interface. Disabled for the parallel one.
DS2 (For Serial Interface Only)
No.
1
2
3
4
Function
ON
Baud rate and parity
setting
Table 1
Table 2
OFF
Upon Shipment
OFF
OFF
OFF
OFF
See Table 2
DS1-3
DS1-4
Light
OFF
OFF
Standard
ON
OFF
Slitly Dark
OFF
ON
Dark
ON
ON
DS2-4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
DS2-3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
DS2-2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
DS2-1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Parity
None
None
None
None
None
None
Odd
Odd
Odd
Odd
Odd
Even
Even
Even
Even
Even
32
Baud Rate
9,600 bps
1,200
2,400
4,800
9,600
19,200
1,200
2,400
4,800
9,600
19,200
1,200
2,400
4,800
9,600
19,200
CITIZEN
CBM-270 User’s Manual
5 .3
Jumper Wire Function
The jumper wires have been set at shipment.
The following lists the basic settings at
shipment. Check the settings by performing self-printing.
Jumper Wires
No.
J1
J2
J3
J4
J5
J6
J7
J8
Function
Upon
Shipment
Short
See Table 3
Short
Short
7 bits
8 bits
Open
Open
Black mark Label interval
Open
Open
Ignored
"?" printed
Open
Short
International character
Data bit length
Unused
Label detection
Unused
Communication error mark
Open
* J4: Serial interface only. Disabled for the parallel one.
* J5~J7: Do not change the shipment settings.
Table 3
No.
J1
J2
J3
USA
Short
Short
Short
France
Open
Short
Short
Germany
Short
Open
Short
U.K.
Open
Open
Short
Denmark-I
Short
Short
Open
Sweden
Open
Short
Open
Italy
Short
Open
Open
Japan
Open
Open
Open
CAUTION:
1) Never change the settings of the jumper wires.
2) If you want to change their settings, consult us.
3) Never disassemble the printer body. It could cause trouble, etc.
33
CITIZEN
CBM-270 User’s Manual
6.
6 .1
PARALLE
LLEL INTERFACE
Specifications
·Data input system
: 8-bit parallel (DATA1 to DATA8)
·Control signals
: ACK, BUSY, STROBE, FAULT, PE, RESET
·Applicable connectors : Printer side : 57LE-40360 (Anphenol) or its equivalent
Cable side
6 .2
: 57-30360 (Anphenol) or its equivalent
Conne
nnector's Pin Configuration
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Signal Name
STROBE
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
ACK
BUSY
PE
+ 5V DC
GND
FRAME GND
34
No.
Signal Name
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
TWISTED PAIR GND
RESET
FAULT
GND
CITIZEN
CBM-270 User’s Manual
6 .3
6.3.1
Input and Output Signals
Input and Output Signals
(1) Input signals to the printer
·DATA
: 8-bit parallel signal (Positive logic)
·STROBE
: Strobe signal to read the 8-bit data (Negative logic)
·RESET
: Signal to reset the entire printer (Negative logic); 1 ms or more
(2) Output signals from the printer
·ACK
: 8-bit data request signal.
A pulse signal to be output at the end of the
BUSY signal (Negative logic)
·BUSY
: Signal to indicate that the printer is busy. Input new data when it is "Low."
(Positive logic)
·FAULT
: Turned to "Low" when the printer has an alarm. At this time, all the control
circuits in the printer stop. (Negative logic)
·PE
: Output if the printing paper has run out or is running out. (Positive logic)
(3) Power source and the related
·+5 V DC
: 5 V output pulled up by a 10kW resistor
·GND
: Common ground for the circuits
35
CITIZEN
CBM-270 User’s Manual
6.3.2
Electrical Characteristics
(1) Input signal level
All the input signals are at the TTL level.
High level --- 2.0 V at minimum
Low level --- 0.8 V at maximum
(2) Output signal level
All the output signals are at the TTL level.
High level --- 2.4 V at minimum
Low level --- 0.4 V at maximum
(3) Input and output conditions
The STROBE and RESET input signals are pulled up at 10kW, and the other input signals
at 50kW, respectively.
[Printer Side]
[Host Side]
All the output signals are pulled up at 50kW.
[Printer Side]
[Host Side]
36
CITIZEN
CBM-270 User’s Manual
6.3.3
Timing Char t
Data Input and Print Timings
6.3.4
T1, T2, T3
0.5 ms MIN
T4
270 ns MAX
T5
2.3 ms TYP
T6
500 ms MIN (At power-on)
Data Receiving Control
The data can be received from the host when the BUSY signal is at "Low," but cannot be
received when it is "High."
6.3.5
Buffering
The host side is immediately freed, because 2 KB data can be buffered.
37
CITIZEN
CBM-270 User’s Manual
7.
7 .1
SERIAL INTERFACE
ACE
Specifications
(1) Synchronous system : Asynchronous
(2) Baud rate
: 1,200, 2,400, 4,800, 9,600, 19,200 bps (Selected by the user)
(3) 1-word configuration
Start bits
: 1 bit
Data bits
: 8 bits or 7 bits (Setting upon shipment)
Parity bits
: Odd, even, or no parity (Selected by the user)
Stop bits
: 1 bit or more
(4) Signal polarity
RS-232C
·Mark
= Logic "1" (-3 ~ -12 V)
·Space
= Logic "0" (+3 ~ +12 V)
(5) Received data (RXD signal)
·Mark
= 1
·Space
= 0
(6) Reception control (DTR signal)
·Mark
:
Data not transferable
·Space
:
Data transferable
(7) Transmission control (TXD signal)
7 .2
·DC1 code(11H) X-ON
:
Data receivable
·DC3 code(13H) X-OFF
:
Data not receivable
Conne
nnector's Pin Configuration
No.
1
7
3
20
2
6
Signal Name
FG
GND
RXD
DTR
TXD
DSR
Input/Output
Input
Output
Output
Input
Function
Frame Ground
Signal Ground
Received Data
Printer BUSY Signal
Transmitted Data
Data Set Ready
[Note] 1. The RS-232C signals are based on the EIA RS-232C.
2. The received data should be always maintained in the Mark status when no data is
being transferred.
Applicable connectors (D-Sub connectors)
Printer side : 17LE-13250 (Anphenol) or its equivalent
Cable side : 17JE-23250 (Anphenol) or its equivalent
38
CITIZEN
CBM-270 User’s Manual
7 .3
7.3.1
Input and Output Signals
Input and Output Signals
(1) RXD
Serial received data signal.
If a framing error, overrun error, or parity error takes place,
the relevant data will be printed as "?".
(2) DTR
Write the data or a command when this signal is Ready. If you write at Busy, the previous
data will be ignored, resulting in an overrun error.
buffer even during printing.
The data can be written in the input
Busy is also issued at power-on, during test printing, at on-
line, or at reset.
(3) TXD
If the remaining capacity of the input buffer comes to 128 bytes or less while receiving the
data, DC3(13H) will be output as a data not receivable signal.
If the remaining capacity
comes to 256 bytes or more, DC1(11H) will be output to the host side as a data receivable
signal.
When sending the status information, it is confirmed that DSR is a space prior to sending
the data, if DTR/DSR control has been selected. If DTR/DSR control has not been selected,
the data will be sent, ignoring the DSR signal.
(4) FG
Ground for the case
(5) GND
Common ground for the circuits
39
CITIZEN
CBM-270 User’s Manual
7.3.2
Data Configuration
t
Mark
b0, b1, b2, · · · ·
Space
(1)
(2)
(3)
(1) Start Bit
(2) Data Bit (+ Parity Bit)
(3) Stop Bit (1 or More)
(1) Start bit
The system reads the status again after a lapse of 1/2 bit from a fall edge from the mark to
space, and if it is a space, this bit will be recognized as the start bit.
If it is a mark, the system will not recognize the bit as the start bit and try to detect the
start bit again without judging it as an error.
(2) Data bits + Parity bit
The system samples the data bits and parity bit for the 1 bit worth of time from 1/2 start bit
and assumes the then status as the data for the relevant bits. The bits are called Bit 0, Bit
1, ..., Parity bit, counting from the one closest to the start bit.
(3) Stop bit
The stop bit is the Mark level of 1 bit or more.
If a space is detected in detecting the stop
bit, a framing error will result.
7.3.3
Er ror Detection
The system detects a parity, framing, or overrun error.
If an error is detected, the relevant
data will be stored in the buffer as "?".
(1) Parity error
With a parity check specified, if an error is detected at parity check time, the relevant
data will be stored in the buffer as "?".
(2) Framing error
This error results if the Space status is detected at stop bit detection time.
The
relevant data will be stored in the buffer as "?".
(3) Overrun error
If an overrun error is detected, the relevant data will be stored in the buffer as "?".
40
CITIZEN
CBM-270 User’s Manual
7.3.4
Data Receiving Control
If DTR/DSR control has been selected, the data from the host side will be received when the
BUSY signal is at "Low," but not received when at "High."
If DTR/DSR has not been
selected, the data from the host side will be received after sending XON, but not after sending
XOFF.
7.3.5
Buffering
To transfer the data to the input buffer, there are two control signals available: DTR signal
and TXD signal.
The host side is immediately freed, since the data can be buffered up to 2
KB.
(1) DTR signal (See 7.3.1-(2))
(2) TXD signal (See 7.3.1-(3))
7.3.6
Electrical Characteristics
RS-232C Circuit
Input (RXD, DSR)
[Printer Side]
[Host Side]
RXD
Mark=(-8V): Stop bit
Space=(+8V): Start bit
Equivalent MAX232
Output (TXD, DTR)
[Printer Side]
[Host Side]
Equivalent to MAX232
DTR
Mark=(-8V): At Busy
TXD
Space=(+8V): At Busy
41
Mark=(-8V): 1
Space=(+8V): 0
CITIZEN
CBM-270 User’s Manual
8.
POWER CO
CONNECTOR
This connector is to supply the power from the special AC adapter(27AD).
Connector Schematic
No.
Function
1
2
7.2V
GND
1
Jack used
Inner terminal
: Minus pole (GND)
Outer terminal
: Plus pole
2
: HEC0470-01-640 (HOSHIDEN) or its equivalent
Applicable plug : JXP series type A (I.D.: 2.45 mm, O.D.: 5.5 mm) (HOSHIDEN) or its
equivalent
CAUTION:
1) Be sure to use the specified AC adapter. Use of any other power source could cause trouble to
or break the printer.
2) Do not connect the power source with different polarity.
3) After using the printer or when not using it for a long period of time, be sure to unplug the AC
adapter from a plug socket for your safety.
42
CITIZEN
CBM-270 User’s Manual
9.
MAINTENANCE AN
AND SERVICE
For the information on maintenance and service, please contact our dealer or at the following
address.
North America
Other Areas
CBM America Corporation
Japan CBM Corporation
Service Center
Information Systems Division
365 Van Ness Way
1-1-7 Okubo Shinjuku-ku,
Suite 510
Tokyo 169-8553 Japan
Torrance, CA 90501, U.S.A
TEL +1-310-781-1460
TEL +81-3-3200-6970
FAX +1-310-781-9157
FAX +81-3-3200-6297
43
CITIZEN
CBM-270 User’s Manual
10.
10. PRINT CONTROL FUNC
UNCTIONS
10.
10.1 Comma
mmand List
Function
Command
Code
Page
1
HT
Horizontal tab
09H
33
2
LF
Printing and paper feed
0AH
34
3
CR
Print
0DH
35
4
ESC SP
Setting the right spacing of the character
1BH 20H n
35
5
ESC !
Collective Specifying the printing mode
1BH 21H n
36
6
ESC %
Specifying/Canceling download character set
37
7
ESC &
Defining download characters
8
ESC *
Specifying the bit image mode
9
ESC -
Specifying/Canceling underline
1BH 25H n
1BH 26H s n m
[a p1 p2¼psxa]
m-n+1
1BH 2AH m n1
n2 [d]k
1BH 2DH n
10
ESC 2
Specifying 1/6-inch line feed rate
1BH 32H
41
11
ESC 3
Setting line feed rate of minimum pitch
1BH 33H n
42
12
ESC =
Data input control
1BH 3DH n
42
13
ESC @
Initializing the printer
43
14
ESC D
Setting horizontal tab position
43
15
ESC E
Specifying/Canceling highlighting
1BH 40H
1BH 44H [n]k
00H
1BH 45H n
16
ESC G
Specifying/Canceling double printing
1BH 47H n
44
17
ESC J
Printing and feeding paper n/203 inch
1BH 4AH n
45
18
ESC R
Selecting the international character set
1BH 52H n
46
19
ESC V
Specifying/Canceling 90°-right- turned characters
1BH 56H n
47
20
ESC a
21
ESC c 3
Aligning the characters
1BH 61H n
Selecting the paper near end sensor valid for a paper
1BH 63H 33H n
end signal output
22
ESC c 4
Selecting the paper near end sensor valid for print stop
1BH 63H 44H n
49
23
ESC c 5
Enabling/Disabling the panel switches
1BH 63H 45H n
50
24
ESC d
Printing and feeding the paper by n lines.
1BH 64H n
50
25
ESC i
NOP
26
ESC m
NOP
27
ESC n
Setting a remaining amount of printout
1BH 6EH n
51
28
ESC t
Selecting the character codes table
1BH 74H n
51
29
ESC v
Transmitting the printer status
1BH 76H n
52
30
ESC {
Specifying/Canceling the inverted characters
1BH 7BH n
53
31
ESC $
Specifying the absolute positions
1BH 24H n1 n2
54
32
ESC ¥
Specifying the relative positions
1BH 5CH n1 n2
55
44
38
39
41
44
48
49
CITIZEN
CBM-270 User’s Manual
Function
Command
Code
Page
33
GS k
Printing the bar code
34
GS w
Specifying the horizontal size(Scale factor) of bar code
1DH 6BH n [‘d’]
k 00H
1DH 77H n
35
GS h
Specifying the height of the bar code
1DH 68H n
74
36
GS H
Selecting the print position of HRI code
1DH 48H n
75
37
GS f
Selecting the font of HRI code
76
38
GS *
Defining the download, bit image
39
GS /
Printing the download, bit image
1DH 66H n
1DH 2AH
n1
n2 [d] n1 x n2 x 8
1DH 2FH m
40
GS :
Starting/Ending macro definition
79
41
GS ^
Executing the macro
80
42
DC2 A
Selecting the printing speed
1DH 3AH
1DH 5EH n1 n2
n3
1DH 41H n
43
DC3
Switching the Red/Black printing
13H n
81
44
FF
Printing and Paper feeding to the top of the label
0CH
82
45
GS FF
Printing and discharging the labels (Cutting included)
82
46
GS C0
Setting the numbering print mode
47
GS C1
Setting the numbering counter mode (A)
48
GS C2
Setting the numbering counter
49
GS C ;
Setting the numbering counter mode (B)
50
GS c
Printing the counter
1DH 0CH
1DH 43H 30H m
n
1DH 43H 31H n1
n2 n3 n4 n5 n6
1DH 43H 32H n1
n2
1DH 43H 3BH
N1 3BH N2 3BH
N3 3BH N4 3BH
N5 3BH
1DH 63H
51
GS <
Initializing the printer mechanism
1DH 3CH
87
52
GS A
Correctting the label top position
1DH 41H m n
87
70
74
77
78
81
83
84
85
85
86
Note) n, n1, n2, n3, n4, n5, n6, m, a, s, p, d, N1, N2, N3, N4, and N5 in the table are
parameters for each command.
Note) [ ]k in the table denotes k-times of repeat.
45
CITIZEN
CBM-270 User’s Manual
10.
10.2 Comma
mmand Details
ils
10.
10.2.1
Descri
criptions of Each Item
XXXXX
[Function]
Command Function
[Code]
A sequence of code constituting a command is represented in hexadecimal
number for <
>H, binary number for <
>B, and decimal number for <
>,
respectively; [ ]k represents a repeat count of k-times.
[Range]
Describes an argument value(Setting range) for the command.
[Outline]
Describes a command outline.
[Caution]
Describes a caution as required.
[Default]
Describes an initial value for the command when accompanied by an
argument.
[See Also]
Describes the associated commands for use.
[Sample Program] Describes a coding example in the Q-BASIC sample program.
* This example is only for your reference and differs depending on the
language used, version, and so on.
For details, see the manual for the
language used.
[Print Result]
Shows a print result obtained by running the above-mentioned program.
However, the print result shown here has a different scale from the actual
print result.
XXXX
Represents the command.
46
CITIZEN
CBM-270 User’s Manual
10.
10.2.2
Comma
mmand Details
ils
HT
[Function]
Horizontal tab
[Code]
<09> H
[Outline]
Shifts the printing position to the next horizontal tab position.
·Ignored when the next horizontal tab position has not been set.
[Caution]
·The horizontal tab position is set by ESC D.
·Initial setting of the horizontal tab position is each 8 characters in 9th, 17th,
25th, 33rd, columns.
[See Also]
ESC D
[Sample Program]
LPRINT "0123456789012345678901" ;
LPRINT CHR$ (&HA) ;
LPRINT CHR$ (&H9) ; "AAA" ;
LPRINT CHR$ (&H9) ; "BBB" ;
LPRINT CHR$ (&HA);
LPRINT CHR$ (&H1B) ; "D" ;
LPRINT CHR$ (3) ; CHR$ (7) ; CHR$ (14) ; CHR$ (0) ;
LPRINT CHR$ (&H9) ; "AAA" ;
LPRINT CHR$ (&H9) ; "BBB" ;
LPRINT CHR$ (&H9) ; "CCC" ; CHR$ (&HA) ;
END
[Print Results]
47
CITIZEN
CBM-270 User’s Manual
LF
[Function]
Printing and Paper Feed
[Code]
<0A>H
[Outline]
Prints data inside the input buffer and feeds lines based on the line feed amount
having been set.
·The head of the line becomes the next print starting position.
[See Also]
ESC 2, ESC 3
[Sample Program]
[Print Results]
LPRINT "AAA" ; CHR$ (&HA) ;
LPRINT "BBB" ; CHR$ (&HA) ;
LPRINT CHR$ (&HA) ;
LPRINT "CCC" ; CHR$ (&HA) ;
END
48
CITIZEN
CBM-270 User’s Manual
CR
[Function]
Print
[Code]
<0D>H
[Outline]
1) When DS1-2 is OFF:
This command is ignored.
[See Also]
2) When DS1-2 is ON:
With data held inside the internal print buffer, printing and line feed are
performed.
Without data inside the internal print buffer, however, no printing is
performed.
LF
[Sample Program]
[Print Results]
LPRINT "AAA" ; CHR$ (&HD) ;
When DS1-2 is OFF
LPRINT "BBB" ; CHR$ (&HD) ;
LPRINT CHR$ (&HD) ;
LPRINT "CCC" ; CHR$ (&HD) ;
When DS1-2 is ON
END
ESC
SP
n
[Function]
Setting the right spacing of the character
[Code]
<1B> H <20> H <n>
[Range]
0 £ n £ 32
[Outline]
The rightward space amount is set in dot unit (1/203 inch unit).
value, it is n=0.
[Caution]
The rightward space amount in double wide mode is made double of the set
volume.
[Default]
In the initial
n=0
[Sample Program]
[Print Results]
LPRINT CHR$ (&H1B) ; " " ; CHR$ (0) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; " " ; CHR$ (1) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; " " ; CHR$ (12) ;
LPRINT "AAAAA" ; CHR$ (&HA)
END
49
CITIZEN
CBM-270 User’s Manual
50
CITIZEN
CBM-270 User’s Manual
ESC
!
n
[Function]
Collective specifying the printing mode
[Code]
<1B> H <21> H <n>
[Range]
0 £ n £ 255
[Outline]
Printing mode is assigned. Each n bit indicates the following:
Bit
Function
0
1
2
3
4
5
6
7
Character Font
Undefined
Undefined
High-lighting
Double height
Double width
Undefined
Underline
0
Font A
Value
1
Font B
Canceled
Canceled
Canceled
Specified
Specified
Specified
Canceled
Specified
[Caution]
· With double height and double width being specified simultaneously, double
wide and double high characters are consisted.
· An underline is attached to the full character width, which, however, is not
attached to the part having been skipped by the horizontal tab. Neither is it
attached to 90°-right-turned characters.
· The underline width is as having been specified by <ESC - >. (The default
setting is 1 dot width. )
· Specification with this command is invalid to Kanji, except specification and
cancellation of highlighting
· In case that double wide character and normal character exist in same one line,
the layout of underline is consistent one.
[Default]
n=0
[See Also]
ESC E, ESC -
[Sample Program]
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&H00) ; "H" ;
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&H01) ; "H";
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&H08) ; "H";
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&H10) ; "H";
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&H20) ; "H";
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&H80) ; "H";
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&HB9) ; "H";
LPRINT CHR$ (&HA) ;
END
[Print Results]
51
CITIZEN
CBM-270 User’s Manual
ESC
%
n
[Function]
Specifying/Canceling download character set
[Code]
<1B> H <25> H <n>
[Range]
0 £ n £ 255
[Outline]
Specifying/canceling download characters.
Further, only the lowest bit (n0) is valid for n.
The lowest bit (n0) indicates the following.
n0
0
1
Function
Canceling download character set
Specifying download character set
[Caution]
Download characters
simultaneously.
[Default]
n=0
[See Also]
ESC &
and
download
bit
images
can
not
be
defined
[Sample Program]
GOSUB *SETCHR
DATA
6
LPRINT CHR$ (&H1B) ; "%" ; CHR$ (0) ;
DATA
&HFF, &H80, &H00
LPRINT "@A" ; CHR$ (&HA) ;
DATA
&H80, &H80, &H00
LPRINT CHR$ (&H1B) ; "%" ; CHR$ (1) ;
DATA
&H80, &H80, &H00
LPRINT "@A" ; CHR$ (&HA) ;
DATA
&H80, &H80, &H00
END
DATA
&HFF, &HFF, &HFF
DATA
&HFF, &HFF, &HFF
*SETCHR :
LPRINT CHR$ (&H1B) ; "&" ;
DATA
12
LPRINT CHR$ (3) ; "@" ; "A" ;
DATA
&HFF, &HFF, &HFF
FOR J=1 TO 2
DATA
&H80, &H07, &HF9
READ REP
DATA
&H80, &HFF, &HF9
LPRINT CHR$ (REP) ;
DATA
&H87, &HFE, &H01
FOR I=1 TO REP*3
DATA
&H9F, &H06, &H01
READ D
DATA
&HF8, &H06, &H01
LPRINT CHR$ (D) ;
DATA
&HF8, &H06, &H01
DATA
&H9F, &H06, &H01
NEXT J
NEXT I
DATA
&H87, &HFE, &H01
RETURN
DATA
&H80, &HFF, &HF9
DATA
&H80, &H07, &HF9
DATA
&HFF, &HFF, &HFF
[Print Results]
52
CITIZEN
CBM-270 User’s Manual
ESC
&
s
n m
[a [p] s´a]
m-n+1
[Function]
Defining the download characters
[Code]
<1B> H <26> H <s> <n> <m> [<a> <p1> <p2> ¼ <ps´a>] m-n+1
[Range]
s=3
32 £ n £ m £ 126
0 £ a £ 12 (Font A)
0 £ a £ 9 (Font B)
[Outline]
[Caution]
0 £ p1 ¼ ps´a £ 255
Defines the font of download characters of alphanumeric characters.
· "s" indicates the number of bytes in vertical direction.
· "n" indicates the start character code and m the end character code. To define
only one character, set n=m.
· Character codes definable includes 95 ASCII codes in total between 32~126.
· "a" indicates the number of dots in horizontal direction for definition.
· "p" is the data to be defined, which indicate a pattern equal to "a" dot in
horizontal direction from the left end. The rest of the pattern on the right side
is filled with space.
The rest of data to be defined is s x a.
· Download characters thus defined remain valid until redefinition, ESC @
execution, GS * execution, or power OFF is practiced.
Download characters
simultaneously.
and
download
bit
images
can
not
be
defined
Running this command clears the definition of the download bit image.
[Default]
Same as the internal character set
[Example]
Create each data bit by setting "1" for a printed dot and "0" for an unprinted dot.
[Sample Program]
[Print Results]
See Sample Program and Print Results for ESC % on Page 50.
53
CITIZEN
CBM-270 User’s Manual
ESC * m
n1 n2
[d]
k
[Function]
Specifying the bit image mode
[Code]
<1B> H <2A> H <m> <n1> <n2> [<d>] k
[Range]
m= 0, 1, 32, 33
0 £ n1 £ 255
0 £ n2 £ 1
0 £ d £ 255
[Outline]
k = n1 + 256 ´ n2
(m = 0, 1)
k = (n1+ 256 ´ n2) ´ 3
(m = 32, 33)
According to the number of dots specified in n1, n2, specify the bit image of mode n.
· The No. of dots printed is divided by 256, whose quotient is taken as n2 and
residualas n1.
· The total no. of dots printed in the bit image is equal to n1 + (256 ´ n2).
· When bit image data have been input in excess of dot position of one line (448
dots) , the excess data are discarded.
· d is bit image data, the bits subject to printing are taken as "1" and those not as
"0".
· The bit image modes specified by m are shown as follows:
m
Mode
0
1
32
33
8-dot single density
8-dot double density
24-dots single density
24-dots double density
[Caution]
Vertical Direction
No. of Dots
Dot Density
8
67 DPI
8
67 DPI
24
203 DPI
24
203 DPI
Horizontal Direction
Dot Density
Max. No. of Dots
101 DPI
192
203 DPI
384
101 DPI
192
203 DPI
384
·When the values set in m (Bit image mode) are out of the above range, the data
following after n1 is processed as normal printing data.
· After completion of bit image printing, printer returns to normal data
processing mode.
[Example]
54
CITIZEN
CBM-270 User’s Manual
[Sample Program]
LPRINT CHR$ (&H1B) ; "*" ;
LPRINT CHR$ (0) ; CHR$ (20) ; CHR$ (0) ;
*IMG1:
GOSUB *IMG1
LPRINT CHR$ (&HFF) ;
LPRINT CHR$ (&HA) ;
FOR I=1 TO 18
LPRINT CHR$ (&H1B) ; "*" ;
LPRINTCHR$ (&H85) ;
LPRINT CHR$ (1) ; CHR$ (20) ; CHR$ (0) ;
NEXT I
GOSUB *IMG1
LPRINT CHR$ (&HFF) ;
LPRINT CHR$ (&HA) ;
RETURN
LPRINT CHR$ (&H1B) ; "*" ;
*IMG2 :
LPRINT CHR$ (32) ; CHR$ (20) ; CHR$ (0) ;
GOSUB *IMG2
FOR I=1 TO 3
LPRINT CHR$ (&HFF) ;
LPRINT CHR$ (&HA) ;
NEXT I
LPRINT CHR$ (&H1B) ; "*" ;
FOR I=1 TO 18
LPRINT CHR$ (33) ; CHR$ (20) ; CHR$ (0) ;
LPRINTCHR$ (&H80) ;
GOSUB *IMG2
LPRINTCHR$ (&H00) ;
LPRINT CHR$ (&HA) ;
LPRINTCHR$ (&H05) ;
END
NEXT I
FOR I=1 TO 3
LPRINT
CHR$ (&HFF) ;
NEXT I
RETURN
[Print Results]
8-dots single density
8-dots double density
24-dots single density
24-dots double density
55
CITIZEN
CBM-270 User’s Manual
ESC - n
[Function]
Specifying/Canceling underline
[Code]
<1B> H <2D> H <n>
[Range]
0£n£2
[Outline]
Specifying/canceling an underline.
· Types of underlines by n value are shown below:
[Caution]
[See Also]
n
Type
0
Canceling an underline.
1
Specifying an underline for 1-dot width
2
Specifying an underline for 2-dots width
· An underline is attached to the full character width. It is, however, not
attached to the part having been skipped by horizontal tab command.
· An underline is not attached to a 90 °- right-turned characters.
· Specification/cancellation with this command is invalid to Kanji.
ESC !, FS -
[Sample Program]
LPRINT CHR$ (&H1B) ; "-" ; CHR$ (0) ;
LPRINT "AAAAA" ;
LPRINT CHR$ (&H1B) ; "-" ; CHR$ (1) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
END
[Print Results]
ESC
2
[Function]
Specifying 1/6-inch line feed rate
[Code]
<1B> H <32> H
[Outline]
The line feed rate per line is specified by 1/6 inch.
[Sample Program]
[Print Results]
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "3" ; CHR$ (0) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "3" ; CHR$ (50) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "2" ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT "AAAAA" ;
LPRINT CHR$ (&H1B) ; "J" ; CHR$ (100) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
56
CITIZEN
CBM-270 User’s Manual
ESC
3
n
[Function]
Setting line feed rate of minimum pitch
[Code]
<1B> H <33> H <n>
[Range]
0 £ n £ 255
[Outline]
The line feed rate per line is specified by n/360 inch.
Since an actual mechanical pitch is 1/203 inch, it is internally converted
approximate to the value specified with this command.
[Default]
·The initial value is n = 60 (1/6 inch) (18H), being 4.23 mm line feed rate.
[Sample Program]
[Print Results]
See Sample Program and Print Results for ESC 2 on Page 54.
ESC
=
n
[Function]
Data input control
[Code]
<1B> H <3D> H <n>
[Range]
0 £ n £ 255
[Outline]
Selecting equipment in which data input from the host is effective.
· Each bit of n indicates as follows:
Bit
Equipment
0
1
2
3
4
5
6
7
Printer
Not defined
Not defined
Not defined
Not defined
Not defined
Not defined
Not defined
0
Invalid
Value
1
Valid
· When the printer has not been selected, this printer abandons all the received
data until it is selected by this command.
[Caution]
· Even when the printer has not been selected, it can become BUSY state
through printer operation.
· When the printer is deselected, this printer discards all the data until it is
selected with this command.
[Default]
n=1
[Sample Program]
[Print Results]
LPRINT "AAAAA" ;
LPRINT CHR$ (&H1B) ; "=" ; CHR$ (0) ;
LPRINT "aaaaa" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "=" ; CHR$ (1) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
57
CITIZEN
CBM-270 User’s Manual
ESC
@
[Function]
[Code]
[Outline]
Initializing the printer
<1B> H <40> H
Clears data stored in the print buffer and brings various settings to the initial
state (Default state).
[Caution]
· Data inside the internal input buffer are not cleared.
· Dip switches setting are red once again.
[Sample Program]
[Print Results]
LPRINT CHR$ (&H1B) ; " ! " ; CHR$ (&H30) ;
LPRINT CHR$ (&H1B) ; "V" ; CHR$ (1) ;
LPRINT "AAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "@" ;
LPRINT "AAA" ; CHR$ (&HA) ;
ESC
D
[n]
k
Each setting has
been initialized by
the reset command.
NUL
[Function]
[Code]
[Range]
Setting horizontal tab position
<1B> H <44> H [<n>] k <00> H
1 £ n £ 255
0 £ k £ 32
[Outline]
Specifying a horizontal tab position.
· "n" indicates the no. of columns from the beginning to the horizontal tab
position. At this time, n= set position- 1 is to be specified. For example, to set
the position at 9th column, n=8 is to be specified.
· k denotes the number of horizontal tab positions you want to set.
· The tab position is set at position where it is "character width x n" from the line
beginning. The character width, at this time, includes the rightward space
amount. In double wide characters, it is made double of the ordinary case.
· Tab positions can be specified are maximum 32. Specifying exceeding this is
ignored.
· <n> k, which denotes a setting position, is input in the increasing order and
ends at <00> H.
· ESC D NUL clears all the set tab positions. Following clearing, horizontal
tab command is ignored.
[Caution]
When the data, <n> k, is equal to or smaller than its preceding data, <n> k-1, it is
assumed that tab setting is finished. If this is the case, the next data onward
will be processed as normal data.
When the data, <n> k, exceeds a 1-line print area, set the horizontal tab position,
assuming "Set digit position = Maximum print digits + 1." The horizontal tab
position does not change even if the character width is altered after setting the
horizontal tab position.
[Default]
· Initial value is specified for each eight characters(9th.17th.25th.33rd columns)
of Font A.
[See Also]
HT
[Sample Program]
[Print Results]
See Sample Program and Print Results for HT on Page 46.
58
CITIZEN
CBM-270 User’s Manual
ESC
E
[Function]
[Code]
[Outline]
[Caution]
[See Also]
[Example]
n
Specifying/Canceling highlighting
<1B> H <45> H <n>
Specifying/canceling the highlighting characters.
· "n" is valid only for the lowest bit (n0).
· Control by the lowest bit (n0) is shown as follows:
n0
Type
0
Canceling highlighting
1
Specifying highlighting
· This is effective to all characters.
· Dot configuration of a highlighted character includes one extra dot added at its
side.
· The print result of Double printing and highlight character printing is
completely same.
ESC !, ESC G
[Sample Program]
[Print Results]
LPRINT CHR$ (&H1B) ; "E" ; CHR$ (0) ;
LPRINT "AAABBB" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "E" ; CHR$ (1) ;
LPRINT "AAABBB" ; CHR$ (&HA) ;
ESC
G
[Function]
[Code]
[Outline]
n
Specifying/Canceling double printing
<1B> H <47> H <n>
Specifying/canceling the double printing.
· "n" is valid only for the lowest bit (n0).
· Control by n is shown as follows.
n0
Type
0
Canceling double printing
1
Specifying double printing
This is effective to all characters.
[Caution]
· The print result of Double printing and highlight character printing is
completely same.
[See Also]
ESC E
[Sample Program]
[Print Results]
LPRINT CHR$ (&H1B) ; "G" ; CHR$ (0) ;
LPRINT "AAABBB" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "G" ; CHR$ (1) ;
LPRINT "AAABBB" ; CHR$ (&HA) ;
59
CITIZEN
CBM-270 User’s Manual
ESC
J
n
[Function]
Printing and Feeding paper n/203 inch
[Code]
<1B> H <4A> H <n>
[Range]
0 £ n £ 255
[Outline]
Prints data inside the print buffer and feeds paper by n/360 inch. Since an
actual mechanical pitch is 1/203 inch, it is internally converted approximate to
the value specified with this command.
· Specified volume does not remain.
· The beginning of the line is to be considered as the next printing start position.
· Initial value is not defined.
[Sample Program]
[Print Results]
See Sample Program and Print Results for ESC 2 on Page 54.
60
CITIZEN
CBM-270 User’s Manual
ESC
R
n
[Function]
Selecting the international character set
[Code]
<1B> H <52> H <n>
[Range]
0 £ n £ 10
[Outline]
Depending on the value of n, following character sets are specified.
n
0
1
2
3
4
5
6
7
8
9
10
Character Set
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
Italy
Spain
Japan
Norway
Denmark II
[Default]
An initial value of n is set to 8 for Japan and 0 for International.
[See Also]
Character Code Table (International Character Set)
[Sample Program]
FOR I=0 TO 10
LPRINT CHR$ (&H1B) ; "R" ; CHR$ (I) ;
LPRINT " #$@[¥]^" ;
LPRINT CHR$ (&H60) ; " {
}~ " ;
LPRINT "n=" ; STR$ (I) ;
LPRINT CHR$ (&HA) ;
NEXT I
END
[Print Results]
61
CITIZEN
CBM-270 User’s Manual
ESC
V
n
[Function]
Specifying/Canceling 90°-right- turned characters
[Code]
<1B> H <56> H <n>
[Range]
0£n£1
[Outline]
Specifying/canceling characters 90°-right- turned character.
· "n" means the followings.
n
0
1
Condition
Canceling 90°-right- turned Characters
Specifying 90°-right- turned Characters
[Caution]
· No underlines are attached to 90°-right- turned characters .
[Default]
n=0
[Sample Program]
[Print Results]
LPRINT CHR$ (&H1B) ; "V" ; CHR$ (0) ;
LPRINT "AAAAA" ;
LPRINT CHR$ (&H1B) ; "V" ; CHR$ (1) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
END
62
CITIZEN
CBM-270 User’s Manual
ESC
a
n
[Function]
Aligning the characters
[Code]
<1B> H <61> H <n>
[Range]
0£n£2
[Outline]
All the printed data within one line are aligned in the specified position.
· Depending on n value, positional alignment is carried out as in the table
below:
n
0
1
2
Position
Left end alignment
Centering
Right end alignment
[Caution]
· This is valid only when n is inputted at the beginning of line.
[Default]
n=0
[Sample Program]
LPRINT CHR$ (&H1B) ; "a" ; CHR$ (0) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "a" ; CHR$ (1) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "a" ; CHR$ (2) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
END
[Print Results]
63
CITIZEN
CBM-270 User’s Manual
ESC
c
3
n
(Parallel Interface Only)
[Function]
Selecting the paper near end sensor valid for a paper end signal output
[Code]
<1B>H<63>H<33>H<n>
[Range]
0 £ n £255
[Outline]
This command selects at which paper near end sensor a paper end signal should
be output. Each bit for n has the following meaning:
Bit
Position
0
1~7
Paper near end
Undefined
0
Disabled
Value
1
Enabled
This printer can only select one kind of paper end detection, a paper-near-end
sensor. n is valid for the least significant bit (n0).
[Caution]
This command is valid only for the parallel interface.
[Default]
A default of n is what has been set with the DIP switch (DS1-1).
[Sample Program]
LPRINT CHR$(&H1B);"c3";CHR$(0);
·······When outputting the paper-end signal at the paper end
LPRINT CHR$(&H1B);"c3";CHR$(1);
·······When outputting the paper-end signal at the paper near end
ESC
c
4
n
[Function]
Selecting the paper near end sensor valid for print stop
[Code]
<1B>H<63>H<34>H<n>
[Range]
0 £ n £ 255
[Outline]
This command selects at which paper near end sensor printing should be stopped.
Each bit for n has the following meaning:
Bit
Position
0
1~7
Paper near end
Undefined
0
Disabled
Value
1
Enabled
This printer can only select one kind of paper-end detection, a paper-near-end
sensor. n is valid for the least significant bit (n0).
[Caution]
If print stop is enabled, the printer will print (Feed the paper) 150 cm or an
amount of data specified with the ESC n command and go off-line.
[Default]
A default of n is what has been set with the DIP switch (DS1-1).
[Sample Program]
LPRINT CHR$(&H1B);"c4";CHR$(0);
·······When stopping printing at the paper end
LPRINT CHR$(&H1B);"c4";CHR$(1);
········When stopping printing at the paper near end
64
CITIZEN
CBM-270 User’s Manual
ESC
c
5
n
[Function]
Enabling/Disabling the panel switches
[Code]
<1B> H <63> H <35> H <n>
[Range]
0 £ n £ 255
[Outline]
Selecting the LF switch valid/invalid.
· "n" is valid only in the lowest bit (n0).
· "n" bit means the followings.
n0
0
1
Condition
LF SW valid.
LF SW invalid.
[Caution]
When the panel switch is disabled with this command, the LF switch is disabled.
Therefore, the paper cannot be fed by operating the LF switch.
[Default]
n=0
[Sample Program]
LPRINT CHR$ (&H1B) ; "c5" ; CHR$ (0) ; ········ When enabling the LF switch
LPRINT CHR$ (&H1B) ; "c5" ; CHR$ (1) ; ········ When disabling the LF switch
ESC
d n
[Function]
Printing and feeding the paper by n lines
[Code]
<1B> H <64> H <n>
[Range]
0 £ n £ 255
[Outline]
Prints data inside the buffer and feeds paper by n lines.
· Specified line does not remain.
· The beginning of the line is to be considered as the next printing start position.
[Default]
· The initial value is not defined.
[Sample Program]
LPRINT "AAAAA"
LPRINT CHR$ (&H1B) ; "d" ; CHR$ (2) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
END
[Print Results]
65
CITIZEN
CBM-270 User’s Manual
ESC
n
n
[Function]
[Code]
[Range]
[Outline]
Setting a remaining amount of printout
<1B>H<6E>H<n>
0 £ n £ 255 ("n" in the 2nd byte denotes this command)
This command sets a print remaining amount after detecting PNE. n is set in
units of cm.
[Caution]
If the paper near end sensor is disabled, this command will not function. The set
value and print remaining amount are not cleared by the ESC @ command. If a
value lower than the already set value is set at PNE detection time, the printer
may stop printing. The set value remains valid until it is re-set or the printer is
turned on again.
[Default]
n = 150 (Remaining amount: 150 cm)
[Sample Program]
LPRINT CHR$(&H1B);"n";CHR$(100); ·······When setting the print remaining amount = 100 cm
ESC
t
[Function]
[Code]
[Range]
[Outline]
n
Selecting the character code table
<1B> H <74> H <n>
0£n£1
Selecting Page n on the character code table:
The character code table is selected depending on the value of n.
"n" means the followings.
n
Condition
0
Page 0(IBM Character #2)
1
Page 1(Domestic Character)
[Caution]
International character can not be changed.
Setting condition can be confirmed by self printing
[Default]
An initial value of n is set to 1(Page 1) when the J1~3 are opened,
the other cases, it is set to 0(Page 0).
[See Also]
Character Code Table, ESC R
[Sample Program]
[Print Results]
FOR N=0 TO 1
LPRINT CHR$ (&H1B) ; "t"; CHR$ (N) ;
LPRINT " n= " ; STR$(N) ; " " ;
FOR C=&HB1 TO &HB5
LPRINT CHR$ (C) ;
NEXT C
LPRINT CHR$ (&HA) ;
NEXT N
END
66
CITIZEN
CBM-270 User’s Manual
ESC
v
(Serial Interface Only)
[Function]
Transmitting the printer status
[Code]
<1B> H <76> H
[Outline]
Current printer status is transmitted..
[Caution]
· Status sent out consists of 1 byte whose content is as in the table below.
· In DTR/DSR control, after receptible state of the host (DSR signal being in
SPACE state) is confirmed, only 1 byte is transmitted. In XON/XOFF control,
DSR signal state not being confirmed, only 1 byte is transmitted.
· In DTR/DSR control, when the host is in unreceptible state(DSR signal being
in MARK state), it waits until receptible state is created.
· In paper end (paper near end) status, this command may be unreceptible state
due to BUSY state.
Remarks. This command is valid only for serial interface model.
Bit
Function
0
1
2
3
4
5
6
7
Not defined
Not defined
Paper end
Not defined
Not used
Not defined
Not defined
Not defined
0
Value
1
With paper
Without paper
Fixed to 0
-
[Sample Program]
OPEN "COM1:N81NN" AS #1 ;
PRINT #1, CHR$ (&H1B) ; "v" ;
A$ = INPUT$ (1, #1) ;
CLOSE #1
END
67
CITIZEN
CBM-270 User’s Manual
ESC
{
n
[Function]
Specifying/Canceling Inverted Characters
[Code]
<1B> H <7B> H <n>
[Range]
0 £ n £ 255
[Outline]
Specifying/Canceling inverted characters.
· "n" is valid only for the lowest bit (n0).
· Bit n (n0) means the followings.
n0
0
1
[Caution]
Condition
Canceling inverted characters
Specifying inverted characters
· Inverted printing means printing the line at 180°turned.
· This is valid only when this is specified at the beginning of a line.
[Default]
n=0
[Sample Program]
LPRINT CHR$ (&H1B) ; "{" ; CHR$ (0) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT "BBBBB" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "{" ; CHR$ (1) ;
LPRINT "AAAAA" ; CHR$ (&HA) ;
LPRINT "BBBBB" ; CHR$ (&HA) ;
END
[Print Results]
68
CITIZEN
CBM-270 User’s Manual
ESC
$
n1
n2
[Function]
Specifying the absolute positions
[Code]
<1B> H <24> H < n1> <n2>
[Range]
0 £ n1 £ 255
0 £ n2 £ 1
[Outline]
The printing start position is specified in the number of dots (1/203 inch unit)
from the beginning of line.
· The number of dots is divided by 256, whose quotient is taken as n2 and the
residual as n1.
· Therefore, the printing start position is equal to n1 + n2 ´ 256 from the
beginning of line..
[Caution]
· Specifying beyond the line end is ignored.
[Default]
· The initial value is not specified.
[See Also]
ESC ¥
[Sample Program]
LPRINT CHR$ (&H1B) ; "$" ;
LPRINT CHR$ (0) ; CHR$ (0) ; "A" ;
LPRINT CHR$ (&H1B) ; "$" ;
LPRINT CHR$ (50) ; CHR$ (0) ; "B" ;
LPRINT CHR$ (&H1B) ; "$" ;
LPRINT CHR$ (0) ; CHR$ (1) ; "C" ;
LPRINT CHR$ (&HA) ;
LPRINT CHR$ (&H1B) ; "$" ;
LPRINT CHR$ (100) ; CHR$ (0) ; "A" ;
LPRINT CHR$ (&H1B) ; "¥" ;
LPRINT CHR$ (&HC2) ; CHR$ (&HFF) ; "B" ;
LPRINT CHR$ (&HA) ;
END
[Print Results]
69
CITIZEN
CBM-270 User’s Manual
ESC
¥
n1
n2
[Function]
Specifying the relative positions
[Code]
<1B> H <5C> H <n1> <n2>
[Range]
0 £ n1 £ 255
0 £ n2 £ 255
[Outline]
The printing start position is specified in the number of dots(1/203 inch unit)
from the current position.
· Rightward direction is taken as plus and leftward direction as minus.
· To specify N dot in minus (left) direction, use a complement of N for
assignment.
-N dots = 65536 - N
· The number of dots is divided by 256, whose quotient is taken as n2 and the
residual as n1.
[Caution]
·
Specifying exceeding the top of line or the end of line is ignored.
[Default]
·
The initial value is not specified.
[See Also]
ESC $
[Sample Program]
[Print Results]
See Sample Program and Print Results for ESC $ on Page 67.
70
CITIZEN
CBM-270 User’s Manual
GS
k
n
[d] k
NUL
[Function]
Printing the bar code
[Code]
<1D> H <6B> H <n> [ <d> ] k <00> H
[Range]
[Outline]
0£n£7
Specifying a type of bar code and printing bar codes.
· The beginning of line is considered as the next printing start position.
· Depending on the value of n, the following bar code can be selected.
d indicates a character code to be printed and k indicates the number of character
to be printed.
[Caution]
·
·
·
·
·
[Default]
n
Bar Code System
Maximum Columns
0
UPC-A
1
UPC-E
2
JAN13 (EAN)
3
JAN 8 (EAN)
4
CODE 39
13
5
ITF
22
6
CODABAR (NW-7)
17
7
CODE 128
16
When data being held in the print buffer, this command is ignored.
Regardless of the specified feed pitch, this command feeds the paper to be
required to print a bar code.
If the character code d cannot be printed in the respective bar code system, the
bar code so far will be printed, processing the subsequent data as normal data.
When a bar code whose number of characters to be printed is fixed has been
selected, the number of characters k have to be always made equal to the
number of characters to be printed. (The bar code is not printed when not
matching.)
When the horizontal direction exceeds one line length, the excess part is not
printed.
· The initial value is not specified.
[Description of Bar Codes] <For print examples, see Page 72.>
UPC-A
This bar code, consisting of numerals only, has a fixed length of 12 columns; a
11-column number entered from the host or application software plus a check
column(12th column) automatically calculated inside the printer. If the 12thcolumn numeral is sent from the host, the entire bar code will be printed as it is.
UPC-E
This bar code, consisting of numerals only, has a fixed length of 8 columns; the
first number system character is "0" stationary. A 12-column numeral entered
from the host or application software is compressed to 8 columns with a check
column and printed. The 12th-column check column is automatically calculated
inside the printer and sent from the host, the entire bar code will be printed,
compressed to 8 columns.
71
CITIZEN
CBM-270 User’s Manual
JAN-13(EAN) This bar code, consisting of numerals only, has a fixed length of 13 columns; a
12-column number entered from the host or application software plus a check
column(13th column) automatically calculated inside the printer. If the 13thcolumn numeral is sent from the host, the entire bar code will be printed as it is.
JAN-8(EAN) This bar code, consisting of numerals only, has a fixed length of 8 columns; a 7column number entered from the host or application software plus a check
column(8th column) automatically calculated inside the printer. If the 8thcolumn numeral is sent from the host, the entire bar code will be printed as it is.
CODE39
This bar code, consisting of uppercase alphabets and numerals, has a variable
length of columns. A start/stop code "*" is automatically added by the printer.
Available characters include a space and " $ % * + -. / 0 1 2 3 4 5 6 7 8 9 " and
uppercase alphabets.
ITF
This bar code, consisting of numerals only, has a variable length of even digits.
If an odd-column code is transferred, nothing will be printed.
CODABAR (NW-7)
This bar code, consisting of alphanumerals, has a variable length of columns.
Available characters include " 0 1 2 3 4 5 6 7 8 9 A B C D $ + - . / : " A start/stop
code is required; any one of A, B, C, and D is used.
CODE128
· This bar code consists of all of 128 ASCII code characters and has a variable
length of columns. This printer supports the code subsets A, B, and C. By
prefixing a transfer code with any one character of A, B, and C, you can select the
code subset to start from. If not prefixed with A, B, or C, the code subset B will be
selected.
· The code subset A is the bar code consisting of standard uppercase alphabets,
numerals, symbols, and special codes.
· The code subset B is the bar code consisting of standard uppercase/lowercase
alphabets, numerals, symbols, control codes, and special codes.
· The code subset C is the bar code consisting of special characters and 100
kinds of numbers ranging from 00 to 99.
· The check digit automatically calculated inside the printer is added to the end
of the entered columns to be printed.
· Processing of the special characters
The characters above the ASCII code number 96 are considered special
characters. The following lists the converted characters for entering these
characters.
72
CITIZEN
CBM-270 User’s Manual
ASCII Code
96
97
98
99
100
101
102
Converted
Character
80h
81h
82h
83h
84h
85h
86h
Subset Code A
Subset Code B
Subset Code C
FNC 3
FNC 2
SHIFT
CODE C
CODE B
FNC 4
FNC 1
FNC 3
FNC 2
SHIFT
CODE C
FNC 4
CODE A
FNC 1
-N/A-N/A-N/A-N/ACODE B
CODE A
FNC 1
The following exemplifies a selection of the code subset as a method to utilize the
special characters.
<Selection of Code Subset>
· Initial selection: Enter any one character of A, B, and C.
· Conversion on the way: Enter any one character of 82h through 85h
Example) When initially testing with the code subset B, and then, printing the
bar code, "123," with the code subset A
· Input code
:
B
· Bar code data :
TEST
<85h>
123
<CODE B>TEST<CODE A>123
[Sample Program]
LPRINT CHR$ (&H1D) ; "H" ; CHR$ (2) ;
LPRINT CHR$ (&H1D) ; "k" ;
LPRINT CHR$ (4) ;
LPRINT "123" ; CHR$ (0) ;
[Print Results]
73
CITIZEN
CBM-270 User’s Manual
[Description of Bar Codes]
UPC-A, UPC-E, JAN-13 (EAN), JAN-8 (EAN), CODE39, ITF, CODABAR, CODE128
Type
Print Sample
Bar Code 1
UPC-A
Bar Code 2
UPC-E
Bar Code 3
JAN-13
Bar Code 4
JAN-8
Bar Code 5
CODE39
Bar Code 6
ITF
CODABAR
(NW-7)
Bar Code 7
Bar Code 8
CODE128
Max.
column
Outline of Symbol
12-column fixed-length bar
consisting of numerals only
code
8-column fixed-length bar
consisting
of
numerals
Abbreviated version of UPC-A
code
only.
13-column fixed-length bar
consisting of numerals only
code
8-column fixed-length bar
consisting of numerals only
code
Variable-length bar code consisting of
alphabets and numerals.
The
*
start/stop code " " is automatically
added.
Even-column variable-length bar code
consisting of numerals only
Variable-length bar code consisting of
alphanumerals. Any one of A, B, C,
and D is required as the start/stop
code.
Variable-length bar code consisting of
all 128 ASCII code characters.
-
-
-
-
13
22
17
16
Printing is done depending on bar code specification type, number of print digits,
bar code height, width (Magnification), visible code presence, and bar code data
specification.
74
CITIZEN
CBM-270 User’s Manual
GS
w
n
[Function]
Specifying the horizontal size(Scale factor) of bar code
[Code]
<1D> H <77> H <n>
[Range]
2£n£4
[Outline]
Selecting bar code width.
n denotes the number of dots in fine element width.
[Default]
n=3
[Sample Program]
LPRINT CHR$ (&H1D) ; "h" ; CHR$ (50) ;
LPRINT CHR$ (&H1D) ; "w" ; CHR$ (2) ;
GOSUB *BC
LPRINT CHR$ (&H1D) ; "h" ; CHR$ (80) ;
LPRINT CHR$ (&H1D) ; "w" ; CHR$ (3) ;
GOSUB *BC
LPRINT CHR$ (&H1D) ; "h" ; CHR$ (120) ;
LPRINT CHR$ (&H1D) ; "w" ; CHR$ (4) ;
GOSUB *BC
END
*BC :
LPRINT CHR$ (&H1D) ; "k" ;
LPRINT CHR$ (4) ;
LPRINT "12" ; CHR$ (0) ;
RETURN
Height 50,
Magnification 2
[Print Results]
Height 80,
Magnification 3
Height 120,
Magnification 4
GS
h
n
[Function]
Specifying the height of the bar code
[Code]
<1D> H <68> H <n>
[Range]
1 £ n £ 255
[Outline]
Selecting bar code height.
n denotes the number of dots in the vertical direction.
[Default]
[See also]
n = 162
GS k, GS w
[Sample Program]
[Print Results]
See Sample Program and Print Results for GS w as above.
75
CITIZEN
CBM-270 User’s Manual
GS
H
n
[Function]
Selecting the printing position of HRI characters
[Code]
<1D> H <48> H <n>
[Range]
0£n£3
[Outline]
Selecting printing position of HRI characters in printing bar codes.
· "n" means the followings.
n
0
1
2
3
Printing Position
No printing
Above the bar code
Below the bar code
Both above and below the bar code
The visible code refers to the bar code-turned characters so that you can read
them.
[Caution]
The visible code is printed in the font selected with GS f. Specify before the GS k
command.
[Default]
n=0
[See Also]
GS f
[Sample Program]
[Print Results]
LPRINT CHR$ (&H1B) ; "3" ; CHR$ (5) ;
LPRINT CHR$ (&H1D) ; "h" ; CHR$ (50) ;
LPRINT CHR$ (&H1D) ; "H" ; CHR$ (0) ;
No Visible Code
GOSUB *BC
LPRINT CHR$ (&H1D) ; "H" ; CHR$ (1) ;
GOSUB *BC
LPRINT CHR$ (&H1D) ; "H" ; CHR$ (2) ;
Printed above
GOSUB *BC
LPRINT CHR$ (&H1D) ; "H" ; CHR$ (3) ;
GOSUB *BC
END
Printed below
*BC :
LPRINT CHR$ (&H1D) ; "k" ;
LPRINT CHR$ (4) ;
LPRINT "12" ; CHR$ (0) ;
LPRINT CHR$ (&HA) ;
Printed above
And below
RETURN
76
CITIZEN
CBM-270 User’s Manual
GS
f n
[Function]
Selecting the font of HRI code
[Code]
<1D> H <66> H <n>
[Range]
n = 0, 1
[Outline]
Selecting the font of HRI code in printing bar code.
The type of font can be printed by selecting n is as follows.
n
0
1
Font
Font A
Font B
The visible code refers to the bar code-turned characters so that you can read
them.
[Caution]
The visible code is printed at the position specified with GS h.
[Default]
n=0
[See Also]
GS H
[Sample Program]
LPRINT CHR$ (&H1D) ; "h" ; CHR$ (50) ;
LPRINT CHR$ (&H1D) ; "H" ; CHR$ (2) ;
LPRINT CHR$ (&H1D) ; "f" ; CHR$ (0) ;
GOSUB *BC
LPRINT CHR$ (&H1D) ; "f" ; CHR$ (1) ;
GOSUB *BC
END
*BC :
LPRINT CHR$ (&H1D) ; "k" ;
LPRINT CHR$ (4) ;
LPRINT "123" ; CHR$ (0) ;
LPRINT CHR$ (&HA) ;
RETURN
[Print Results]
FONT A
FONT B
77
CITIZEN
CBM-270 User’s Manual
GS
*
n1
[Function]
[Code]
[Range]
[Outline]
[Caution]
n2 [ d ]
n1 ´ n2 ´ 8
Defining the download, bit image
<1D> H <2A> H <n1> <n2> [ <d> ] n1´n2´8
1 £ n1 £ 255
1 £ n2 £ 48
n1 ´ n2 £ 1311
Defines downloading bit images of the number of dots specified by n1/n2.
· The numbers of dots are n1 ´ 8 in horizontal direction and n2 ´ 8 in vertical
direction.
· d indicates bit image data.
· The download bit image thus defined remains effective until redefinition, ESC
@ execution, ESC &, or power OFF takes place.
· A download character and a download bit image can not be defined
simultaneously.
With this command executed, defined content of a download character is cleared.
[See Also]
· Relations between the bit image data and the dot defined are shown below:
GS /, ESC &
n1´8 dots
n2´8 dots
[Sample Program]
[Print Results]
GOSUB *IMG
LPRINT CHR$ (&H1D) ; "/" ; CHR$ (0) ;
LPRINT CHR$ (&H1D) ; "/" ; CHR$ (1) ;
LPRINT CHR$ (&H1D) ; "/" ; CHR$ (2) ;
LPRINT CHR$ (&H1D) ; "/" ; CHR$ (3) ;
END
*IMG :
N1 = 8 : N2= 8
LPRINT CHR$ (&H1D) ; "*" ;
LPRINT CHR$ (N1) ; CHR$ (N2) ;
FOR J=1 TO N1*8
FOR I=1 TO N2
LPRINT CHR$ (J) ;
NEXT I
NEXT J
RETURN
END
78
Normal Mode
Double Width Mode
Double Height Mode
Quadruple Mode
CITIZEN
CBM-270 User’s Manual
GS
/
m
[Function]
Printing the download, bit image
[Code]
<1D> H <2F> H <m>
[Range]
0£m£3
[Outline]
Prints download bit image in a mode specified by m.
· Modes can be selected by m are shown below.
m
Mode Name
0
1
2
3
Normal mode
Double wide mode
Double high mode
Double wide/double high mode
[Caution]
Dot Density In
Vertical Direction
203 DPI
203 DPI
101 DPI
101 DPI
Dot Density In
Horizontal Direction
203 DPI
101 DPI
203 DPI
101 DPI
· When data exist inside the print buffer, this command is ignored.
· When a download bit image has not been defined, this command is ignored.
· A portion of a download bit image exceeding one line length is not printed.
· A download character and a download bit image cannot be defined
simultaneously.
[Default]
· The initial value is not specified.
[See Also]
GS *
[Sample Program]
[Print Results]
See Sample Program and Print Results for GS * on Page 76.
79
CITIZEN
CBM-270 User’s Manual
GS
:
[Function]
Starting/Ending macro definition
[Code]
<1D> H <3A> H
[Outline]
Specifying starting / ending macro definition.
Means termination when received while defining a macro.
[Caution]
Maximum content available for macro definition is 2048 bytes.
exceeding 2048 bytes is not defined.
A portion
· Even with ESC @ (initialization of the printer) having been executed, defined
content is not cleared. Therefore, it is possible to include ESC @ into the
content of macro definition.
· Normal printing operation is carried out even while in macro definition
[Default]
· Initially, Macro is not specified.
[See Also]
GS ^
[Sample Program]
[Print Results]
LPRINT CHR$ (&H1D) ; " : " ;
LPRINT "+ - - - +" ; CHR$ (&HA) ;
LPRINT "|
|" ; CHR$ (&HA) ;
Normal Printing during
Macro Definition
LPRINT "+ - - - +" ; CHR$ (&HA) ;
LPRINT CHR$ (&H1D) ; " : " ;
LPRINT CHR$ (&H1D) ; " ^ " ;
Printing during Macro Execution
LPRINT CHR$ (2) ; CHR$ (10) ;
LPRINT CHR$ (0) ;
END
80
CITIZEN
CBM-270 User’s Manual
GS
^
n1 n2
n3
[Function]
Executing the macro
[Code]
<1D> H <5E> H <n1> <n2> <n3>
[Range]
0 £ n1 £ 255
0 £ n2 £ 255
0 £ n3 £ 1
[Outline]
Executing contents defined in macro.
· "n1~n3" indicate as follows:
n1 : The number of times of macro execution
n2 : Waiting time on macro execution
Waiting time of n2 ´ 100 msec is given for every execution.
n3 : Macro execution mode
n3
0
1
Mode
Continuous execution
Execution by LF SW
Continuous execution: The Macro is executed n1 times continuously at the time
intervals specified by n2.
Execution by FEED S: After waiting for lapse of time specified by n2, the
ALAME LED flickers and the LF switch is waited to be
pressed. When it is pressed, the macro is executed once.
This action is repeated n1 times.
[Caution]
· When this command is received while in macro definition, suspension of macro
definition is indicated. At this time, the defined content is cleared.
· No execution takes place when macro is held undefined or n1=0.
· While in macro execution with n3=1, paper feed with the LF SW is not
available.
[Default]
· Initially, this command is not specified.
[See Also]
GS :
[Sample Program]
[Print Results]
See Sample Program and Print Results for GS : on Page 78.
81
CITIZEN
CBM-270 User’s Manual
DC2
A
n
[Function]
Selecting a printing speed
[Code]
<12>H<41>H<n>
[Range]
0£n£1
[Outline]
This command specifies a printing command.
significant bit.
[Caution]
[Default]
DC3
n is valid only for the least
n0
Printing Speed
0
Standard print
1
High-speed print
If a printing amount is too much for one line, a standard speed will be assumed.
Bar code printout and download bit image printout are automatically done at a
standard speed. At high-speed printout, printing quality may be deteriorated.
n=1
n
[Function]
[Code]
[Range]
[Outline]
[Caution]
[Default]
Switching the Red/Black printing
<13>H<n>
0 £ n £ 255
This command selects/deselects black/red printout.
significant bit (n0).
n is valid only for the least
n0
Black based paper
n0
Red based paper
0
Deselects red printout
0
Deselects black printout
1
Selects red printout
1
Selects black printout
When deselected : Assumes a standard power-on pulse rate
When selected : Increases a power-on pulse rate to change coloring.
This command is valid only at the beginning of the line. It functions when special
purpose paper is used. Printing color becomes thicker on normal thermal paper.
n=0
[Sample Program]
LPRINT "ABCDEFG" ;CHR$ (&HA) ;
LPRINT CHR$ (&H13) ; CHR& (1) ;
LPRINT "ABCDEFG" CHR& (&HA) ;
END
[Print Result]
When the normal thermal paper is used
Black print
Red print
When the special purpose paper is used
Standard print
High-temperature print
82
CITIZEN
CBM-270 User’s Manual
FF
(Only When Label Printer is Selected)
[Function]
Printing and paper feeding to the top of the label
[Code]
<0C>H
[Outline]
This command prints the data in the printer buffer and searches for the head of
the next label.
[Caution]
This command is valid only when the label printer is selected with DS1-5. It is
ignored when the thermal paper is specified. After sending one label worth of
print data, be sure to send this command or GS FF command. After the user
intentionally moved the label paper, this command cannot search for the head of
the label properly.
[See Also]
GS FF, GS <
[Sample Program]
[Print Result]
LPRINT "ABC" ; CHR$ (&HA) ;
LPRINT "123" ; CHR$ (&HC) ;
LPRINT "HHHHH" ; CHR$ (&HA) ;
LPRINT "gggg" ; CHR$ (&HC) ;
END
GS
FF
(Only When Label Printer is Selected)
[Function]
Printing and discharging the label(Cutting included)
[Code]
<1D>H<0C>H
[Outline]
This command prints the data in the printer buffer and cuts and discharges the
label. If this command is executed, the printer will discharge the label to the
cutting position and flicker the PAPER lamp to stop. After cutting the label,
press the FEED switch to search for the head of the next label.
[Caution]
This command is valid only when the label printer is selected with DS1-5. It is
ignored when the thermal paper is specified. After sending one label worth of
print data, be sure to send this command or FF command. After the user
intentionally moved the label paper, this command can not search for the head of
the label properly.
[See Also]
FF, GS <
83
CITIZEN
CBM-270 User’s Manual
GS
C0
m
[Function]
[Code]
[Range]
[Outline]
m=0
m = 1 to 5
n=0
n=1
n =2
[Caution]
[See Also]
[Default]
n
Setting the numbering print mode
<1D>H<43>H<30>H<m><n>
0£m£5
0£n£5
This command sets the numbering (serial number counter) print mode. m
denotes the number of print columns.
Prints the digits indicated by a numeral. In this case, n has no meaning.
Indicates the maximum number of columns to be printed. If a counter value is
larger than this the number of columns set with this command, the printer will
print the lower m-digits of the counter value.
n specifies a printing position within the printing columns.
Prints the data right justified. The blank columns are spaced.
Prints the data right justified. The blank columns are filled with "0".
Prints the data left justified. The right blank columns are spaced.
If either m or n has a value beyond their ranges, that setting will become invalid.
GS C1, GS C2, GS c, GS C
m = 0, n = 0
[Sample Program]
LPRINT CHR$ (&H1D) ; "C0" ;
* CNT
LPRINT CHR$ (0) ; CHR$ (0) ;
FOR I=1 TO 5
GOSUB * CNT
LPRINT CHR$ (&HID) ; "c" ;
LPRINT CHR$ (&H1D) ; "C0" ;
NEXT I
LPRINT CHR$ (1) ; CHR$ (0) ;
LPRINT CHR$ (&HA) ;
GOSUB * CNT
RETURN
LPRINT CHR$ (&H1D) ; "C0" ;
LPRINT CHR$ (3) ; CHR$ (0) ;
GOSUB * CNT
LPRINT CHR$ (&H1D) ; "C0" ;
LPRINT CHR$ (3) ; CHR$ (1) ;
GOSUB * CNT
LPRINT CHR$ (&H1D) ; "C0" ;
LPRINT CHR$ (3) ; CHR$ (2) ;
GOSUB * CNT
END
[Print Result]
Counts from 1 to 5 at m = 0 and n = 0.
Counts from 6 to 10 at m = 1 and n = 0.
Counts from 11 to 15 at m = 3 and n = 0.
Counts from 16 to 20 at m = 3 and n = 1.
Counts from 21 to 25 at m = 3 and n =2.
84
CITIZEN
CBM-270 User’s Manual
GS
C1
n1
n2
n3
n4
n5
n6
[Function]
Setting the numbering counter mode (A)
[Code]
<1D>H<43>H<31>H<n1><n2><n3><n4><n5><n6>
[Range]
0 £ n1, N2, N3, N4, N5, N6 £ 255
[Outline]
This command sets the numbering (serial number counter) mode.
n1 + n2 ´ 256 (n1 = remainder, n2 = quotient)
: Counter default
n3 + n4 ´ 256 (n3 = remainder, n4 = quotient)
: Counter final value
n5
: Counter step value
n6
: Identical counter print count
(n1 + n2 ´ 256) < (n3 + n4 ´ 256)
: Count-up system
(n1 + n2 ´ 256) > (n3 + n4 ´ 256)
: Count-down system
(n1 + n2 ´ 256) = (n3 + n4 ´ 256) or n5 = 0 or n6 = 0 : Counter stop
[Default]
n1 + n2 ´ 256 = 1
n3 + n4 ´ 256 = 65535
n5 = 1
n6 = 1
[See Also]
GS C0, GS C2, GS c, GS C ;
[Sample Program]
LPRINT CHR$ (&H1D) ; "C0" ;
* CNT
LPRINT CHR$ (3) ; CHR$ (0) ;
FOR I=1 TO 6
LPRINT CHR$ (&H1D) ; "C1" ;
LPRINT CHR$ (&HID) ; "c" ;
LPRINT CHR$ (50) ; CHR$ (0) ;
NEXT I
LPRINT CHR$ (0) ; CHR$ (0) ;
LPRINT CHR$ (&HA) ;
LPRINT CHR$ (5) ; CHR$ (2) ;
RETURN
GOSUB * CNT
LPRINT CHR$ (&H1D) ; "C2" ;
LPRINT CHR$ (5) ; CHR$ (0) ;
GOSUB * CNT
END
[Print Result]
When setting a count-down range = 0 to 50, step
value = 5, repeat count = 2, and start value = 5 to
print a counter value.
When setting a count-down range = 0 to 50, step
value = 5, repeat count = 1, and start value = 50
to print a counter value. (The repeat count is
cleared)
85
CITIZEN
CBM-270 User’s Manual
GS
C2
n1
n2
[Function]
Setting the numbering counter
[Code]
<1D>H<43>H<3B>H<N1><3B>H<N2><3B>H<N3><3B>H<N4><3B>H
<N5><3B>H
<1D>H<43>H<32>H<n1><n2>
[Range]
0 £ n1 £ 255, 0 £ n2 £ 255
[Outline]
This command sets the numbering (serial number counter) value.
n1 + n2 ´ 256 (n1 = remainder, n2 = quotient) becomes a counter value.
[Caution]
If the counter is set with this command, a repeat count of the identical counter
will be cleared. If the counter value is beyond the Range specified with the "GS
C1" or "GS C;" command, the counter will be initialized.
[Default]
Not defined.
[See Also]
GS C0, GS C1, GS c, GS C ;
[Sample Program]
[Print Result]
See the sample program and print result for the GS C1 command on Page 82.
GS
C;
N1;
N2;
N3;
N4;
N5;
[Function]
Setting the numbering counter mode (B)
[Code]
<1D>H<43>H<3B>H<N1><3B>H<N2><3B>H<N3><3B>H<N4><3B>H
<N5><3B>H
<N1>, <N2>, <N3>, <N4>, and <N5> are character codes.
[Range]
0 £ N1, N2, N5 £ 65535
0 £ N3, N4 £ 255
[Outline]
This command sets the numbering (serial number counter) mode and a counter
value.
N1
: Counter default
N2
: Counter final value
N3
: Counter step value
N4
: Identical counter print count
N5
: Counter start value
N1<N2
: Count-up system
N1>N2
: Count-down system
N1 = N2
or
N3 = 0
: Counter stop
or
N4 = 0
86
CITIZEN
CBM-270 User’s Manual
[Caution]
If the N5 counter start value is beyond the counter range specified with N1 and
N2, it is assumed to be N1 = N5. If each value of N1 through N5 contains a
character code other than "0" through "9" , the printer will invalidate the data up
to that parameter and handle the subsequent data as normal print data.
[Default]
N1 = 1
N2 = 65535
N3 = 1
N4 = 1
N5 = 1
[See Also]
GS C0, GS C1, GS C2, GS c
[Sample Program]
LPRINT CHR$ (&H1D) ; "C0" ;
* CNT
LPRINT CHR$ (3) ; CHR$ (0) ;
FOR I=1 TO 6
LPRINT CHR$ (&H1D) ; "C" ;
LPRINT CHR$ (&H1D) ; "c" ;
LPRINT "50 ; 0 ; 5 ; 2 ; 50 ; " ;
NEXT I
GOSUB * CNT
LPRINT CHR$ (&HA) ;
LPRINT CHR$ (&H1D) ; "C ; " ;
RETURN
LPRINT "50 ; 0 ; 5 ; 2 ; 5 ; " ;
GOSUB * CNT
END
[Print Result]
When setting a count-down range = 0 to 50, step
value = 5, repeat count = 2, and start value = 50
to print a counter value.
When setting a count-down range = 0 to 50, step
value = 5, repeat count = 2, and start value = 5 to
print a counter value.
GS c
[Function]
Printing the counter
[Code]
<1D>H<63>H
[Outline]
This command prints the serial number counter data. After setting the current
counter value in the print buffer as the print data (Character string), it
increments or decrements the counter according to the set count mode.
[Caution]
When setting the value in the print buffer, its format depends on the GS C0
command. The count mode depends on the GS C1 or GS C; command. If the
counter final value set with these commands if exceeded by executing the GS c
command, the counter will be initialized to the set default.
[See Also]
GS C0, GS C1, GS C2, GS C ;
[Sample Program]
[Print Result]
See the sample programs and print results for the commands on Pages 82
through 85.
87
CITIZEN
CBM-270 User’s Manual
GS
<
(Only When Label Printer is Selected)
[Function]
Initializing the printer mechanism
[Code]
<1D>H<3C>H
[Outline]
This command initializes the printer mechanism.
[Caution]
This command is valid only when the label printer is selected with DS1-5. Since
it uses one label for scanning, a head search starts from the next label. The
maximum label length and label spacing (Black mark) is 300 mm. Any label
exceeding this limit results in an error.
GS
A
m
n
(Only When Label Printer is Selected)
[Function]
Correctting the label top position
[Code]
<1D>H<41>H<m><n>
[Range]
0 £ m £ 255, 0 £ n £ 10
[Outline]
This command sets the label head search position in terms of correction value for
the default position. m denotes the correcting direction and valid only for the
least significant bit (m0).
m0
0
1
Correcting direction
Corrects in the forward direction
Corrects in the reverse direction
n denotes a correction value; it is set in increments of n/203 inch.
[Caution]
This command is valid only when the label printer is selected with DS1-5. The
correction value remains valid until it is re-set with this command or the power is
turned on again. Any setting beyond the range is ignored.
88
CITIZEN
CBM-270 User’s Manual
11. CHARACTER CO
CODES TABL
ABLE
11.1
Inter national
11.
11.2 Domestic
89
CITIZEN
CBM-270 User’s Manual
11.3
Inter national Character Codes Table
90
CITIZEN
CBM-270 User’s Manual
APPE
PPENDIX 1. BLOCK DI
DIAGRAM
*1 Parallel Interface --- Centronics compliant
Serial Interface
--- RS-232C compliant
91
CITIZEN
CBM-270 User’s Manual
APPE
PPENDIX 2. OUTLI
TLINE DRAWING
92
CITIZEN
CBM-270 User’s Manual
APPE
PPENDIX 3. WALL MOUNT
UNTING HOLES LAYOUT DRAWING
93
CITIZEN
CBM-270 User’s Manual
<<<German>>>
94
CITIZEN
CBM-270 User’s Manual
<VORSICHT>
1. Bitte lesen Sie die Bedienungsanleitung vor dem Betrieb des Geräts aufmerksam durch und bewahren
Sie die Anleitung anschließend für späteres Nachschlagen an einem sicheren Platz auf.
2. Änderungen des Inhalts dieser Anleitung bleiben ohne Vorankündigung vorbehalten.
3. Die Vervielfältigung dieser Bedienungsanleitung ohne vorherige Genehmigung verstößt, auch
auszugsweise, gegen das Urheberschutzrecht.
4. Niemals versuchen, in dieser Anleitung nicht erwähnte Geräteteile eigenhändig zu warten, zerlegen
oder zu reparieren.
5. Bitte beachten Sie, daß wir keinerlei Haftung für Schäden übernehmen, die auf unsächgemäße
Bedienung, falsche Handhabung oder eine ungeeignete Betriebsumgebung zurückzuführen sind.
6. Zur Vermeidung von Unfällen und sonstigen Problemen
ist das Gerät ausschließlich auf die in der
Bedienungsanleitung beschriebene Weise zu betreiben.
7. Daten sind grundsätzlich temporär, d.h. sie können nicht permanent gesichert oder über längere Zeit
gespeichert werden. Es sei deshalb darauf hingewiesen, daß wir für finanzielle Schäden oder
Profitrückgänge als Folge von Datenverlust, Unfällen, Reparaturen, Tests usw. keinerlei Haftung
übernehmen.
8. Bitte wenden Sie sich mit Fragen oder Hinweisen auf Fehler oder Auslassungen im Text dieser
Anleitung an unsere Geschäftsstelle.
9. Beachten Sie jedoch, daß wir, ungeachtet des obigen Punkts 8, keinerlei Haftung für negative
Folgeerscheinungen im Zusammenhang mit dem Betrieb dieses Geräts übernehmen.
95
CITIZEN
CBM-270 User’s Manual
ZU BEACHTENDE SICHERHEITSMASSRE
SSREG
REGELN
Zur Vermeidung von Gefahren gegenüber dem Bediener und anderen Personen und Sachschäden sind
die folgenden Vorsichtsmaßregeln unbedingt zu beachten.
· Der folgende Text beschreibt das Ausmaß der Gefahren und potentiellen Sachschäden, die durch eine
Mißachtung der Bedienungshinweise oder durch die unsachgemäße Handhabung des Geräts
entstehen können.
WARNUNG
UNG
Die Mißachtung dieser Vorsichtsmaßregel kann zu Körperverletzungen
mit möglicher Todesfolge führen.
VORSICHT
Die Mißachtung dieser Vorsichtsmaßregel kann zu Körperverletzungen
oder Sachschäden führen.
Dieses Symbol ruft den Bediener zu erhöhter Wachsamkeit auf.
Dieses Symbol weist auf wichtige Informationen, wie z.B. Bedienungsschritte oder dergleichen,
hin.
96
CITIZEN
CBM-270 User’s Manual
WARNUNG
UNG
· Beim Betrieb des Geräts sind die nachfolgenden Vorsichtsmaßregeln unbedingt zu beachten. Eine
Mißachtung dieser Hinweise kann zu Schäden, Funktionsstörungen, Rauchentwicklung und
Brandgefahr durch Überhitzen und zu elektrischen Schlägen führen.
Der fortgesetzte Betrieb des Geräts in anormalem Zustand, wie z.B. nach einer Beschädigung,
kann Funktionsstörungen, Rauchentwicklung, fremde Gerüche/Geräusche und Brände
verursachen. Wenn anormale Erscheinungen beim Betrieb auftreten, sofort das Gerät stoppen,
den Netzstecker abziehen, und den Fachhändler benachrichtigen. Niemals versuchen, das
Gerät eigenhändig zu reparieren, um ernsthafte Gefahren zu vermeiden.
· Das Gerät vor starken Stößen und Erschütterungen, wie z.B. Tritte, Stampfen, Schläge,
Herunterfallen usw., schützen.
· Das Gerät an einem gut belüfteten Platz aufstellen, und darauf achten, die Belüftungsöffnung
nicht zu blockieren.
· Bei der Aufstellung des Geräts Plätze vermeiden, an denen chemische Reaktionen auftreten,
wie z.B. in einem Labor, sowie Plätze mit salz- oder gashaltiger Umgebungsluft.
· Netz- und Datenkabel niemals am Kabel haltend anschließen oder abziehen. Bei Betrieb,
Verrücken oder Tragen des Geräts darauf achten, daß die Kabel keiner Gewalteinwirkung
ausgesetzt sind.
· Darauf achten, daß keine Fremdköper, wie z.B. Nadeln oder Büroklammern, in das Gerät gelangen.
· Darauf achten, keine Flüssigkeiten auf dem Gerät zu vergießen oder chemische Substanzen
enthaltende Sprays darüber zu versprühen. Bei versehentlichem Naßwerden das Gerät sofort
ausschalten, das Stromanschlußkabel abziehen, das Netzkabel von der Steckdose trennen usw.
und an einen Fachhändler wenden.
· Nicht dieses Gerät zerlegen oder modifizieren. Eine Mißachtung dieser Vorsichtsmaßregel
kann zu Bränden und elektrischen Schlägen führen.
· Das Gerät nur mit der vorgeschriebenen Netzspannung und dem vorgeschriebenen Netzteil
verwenden. Eine Mißachtung dieser Vorsichtsmaßregel kann Brände, elektrische Schläge und
Funktionsstörungen verursachen.
· Wenn das Netzteil herunterfällt, beschädigt wird oder naß wird, sofort von der Steckdose
trennen und sich an einen Fachhändler wenden.
· Das Netzkabel nicht beschädigen, brechen, modifizieren, mit Gewalt biegen/ziehen, verdrehen
oder kurzschließen. Ein beschädigtes Netzteil kann Brände, elektrische Schläge und
Funktionsstörungen verursachen. Wenden Sie sich bei einer Beschädigung des Netzteilkabels
bitte an unsere Kundendienstvertretung.
· Wenden Sie sich bei einer Beschädigung des Netzteilkabels bitte an unsere Kundendienstvertretung.
· Das Netzteil niemals mit nassen Händen anschließen oder trennen. Hierdurch können Brände,
elektrische Schläge und sonstige Probleme entstehen.
· Verpackungsbeutel sind vorschriftsgemäß zu entsorgen oder ansonsten von Kindern
fernzuhalten. Kleinkinder können durch Überstreifen eines Plastikbeutels ersticken.
97
CITIZEN
CBM-270 User’s Manual
VORSICHTSMASSREG
REGELN FÜR DIE AUFSTELLU
LLUNG
· Das Gerät nicht an Plätzen abstellen oder betreiben, an denen es Feuer, Feuchtigkeit oder
direkter Sonnenbestrahlung ausgesetzt ist. Ebenso sind Plätze in der Nähe von Heizkörpern
und sonstigen Wärmenquellen zu vermeiden, an denen Umgebungstemperatur und
Luftfeuchtigkeit nicht den vorgeschriebenen Betriebsbedingungen entsprechen, sowie Plätze,
an denen das Gerät Öl, Metallspänen oder Staub ausgesetzt ist. Andernfalls können
Funktionsstörungen sowie Rauch- und Brandentwicklung die Folge sein.
· Bei der Aufstellung des Geräts Plätze vermeiden, an denen chemische Reaktionen auftreten,
wie z.B. in einem Labor, sowie Plätze mit salz- oder gashaltiger Umgebungsluft. Hierbei
besteht die Gefahr von Bränden und elektrischen Schlägen.
· Den Drucker auf einer ebenen, stabilen Tischplatte an einem gut belüfteten Platz und frei von
Erschütterungen aufstellen.
· Den Drucker nicht an einem Ort aufstellen, wo sein Betrieb behindert werden kann.
· Keine Gegenstände auf den Drucker stellen und keine kleinen Gegenstände wie Papierclips
oder Stifte in der Nähe liegen lassen. Diese können Betriebsstörungen verursachen, wenn sie
in das Gerät gelangen.
· Keine spitzen Gegenstände wie etwa einen Kugelschreiber zur Bedienung des Bedienfelds des
Druckers verwenden. Dadurch können Betriebsstörungen verursacht werden.
· Das Gerät nicht in der Nähe eines Radios oder Fernsehers verwenden und nicht zusammen mit
einem Radio oder Fernseher an die gleiche Steckdose anschließen. Hierdurch können
Empfangsstörungen auftreten.
· Das Gerät ausschließlich mit der vorgeschriebenen Netzspannung und -frequenz betreiben.
Eine Mißachtung dieser Vorsichtsmaßregel kann Brände, elektrische Schläge und
Funktionsstörungen verursachen.
· Das Gerät ausschließlich mit der vorgeschriebenen Netzspannung betreiben. Eine Mißachtung
dieser Vorsichtsmaßregel kann Brände, elektrische Schläge und Funktionsstörungen verursachen.
· Vergewissern, daß die für den Anschluß des Netzkabels verwendete Steckdose über eine
ausreichende Kapazität verfügt.
· Das Gerät nicht zusammen mit anderen Geräten an die gleiche Steckdose anschließen oder lange
Verlängerungskabel verwenden. Andernfalls können Brände und Stromausfälle die Folge sein.
Nicht auf das Netzkabel treten, schwere Gegenstände darauf abstellen, das Netzkabel anderweitig
belasten (ziehen, quetschen) oder den Drucker mit einem derartig belasteten Netzkabel betreiben.
· Erdungskabel niemals an ein Gasrohr anschließen, da hierbei Explosionsgefahr besteht. Vor
dem Anschließen oder Trennen eines Erdungskabels unbedingt zuerst den Netzstecker aus der
Steckdose ziehen.
· Beim Anschließen oder Trennen der Kabel zuerst die Netzversorgung ausschalten, einschließlich
der angeschlossenen Seite, und dann an Stecker und Steckdose haltend anschließen bzw. trennen.
Durch ziehen am Kabel selber kann dieses reißen oder anderweitig beschädigt werden.
· Netzkabel oder Verbindungskabel immer fest anschließen. Durch Anschluß mit umgekehrter
Polarität können Innenbauteile oder Paßflächen beschädigt werden.
· Für Datensignalleitungen abgeschirmte Kabel oder verzwirbelte Doppeladerkabel verwenden,
um Rauschstörungen möglichst gering zu halten. Das Kabel nicht über zu lange Strecken
verlegen oder an gestörte Geräte anschließen. Durch Anschluß an gestörte Geräte kann
fehlerhafter Druck aufgrund von korruptierten Daten usw. verursacht werden.
· Das Gerät an einem Platz in der Nähe einer Steckdose betreiben, wo sich der Netzstecker zum
Unterbrechen der Stromversorgung jederzeit schnell und mühelos abziehen läßt.
· Wenn das Gerät längere Zeit lang nicht benutzt wird, den Stecker abziehen und die Papierrolle
herausnehmen.
· Beim Transport des Geräts die Papierrolle aus dem Papierhalter nehmen.
98
CITIZEN
CBM-270 User’s Manual
VORSICHTSMASSREG
REGELN FÜR DIE HANDHABUNG
UNG
Zur Vermeidung von Problemen sind bei der Handhabung des Geräts die folgenden
Vorsichtsmaßregeln zu beachten.
· Keine andere Betriebsstromquelle als das mitgelieferte Netzteil verwenden. Das Netzteil nicht
für andere Zwecke verwenden.
· Nicht ohne eingelegte Papier drucken.
· Keine Fremdkörper wie Papierclips, Sicherheitsnadeln etc. in den Drucker fallenlassen.
· Darauf achten, keine Flüssigkeiten auf dem Gerät zu vergießen oder chemische Substanzen
enthaltende Sprays darüber zu versprühen.
· Niemals mit spitzen Objekten, wie z.B. einem Kugelschreiber, auf das Bedienfeld drücken.
· Papierblätter niemals zum fortlaufenden Drucken mit Klebestreifen zusammenkleben.
Dadurch kann der Druckkopf beschädigt werden.
· Ein bereits eingezogenes Blatt niemals gewaltsam herausziehen. Beim Öffnen/Schließen der
Druckerabdeckung darauf achten, daß sich das Papier nicht verfängt. Dadurch kann
Papierstau verursacht werden.
· Immer das richtige Papier verwenden. Durch Verwendung anderer Papiersorten kann die
Druckqualität beeinträchtigt oder Probleme mit dem Druckkopf verursacht werden.
Zur Vermeidung von Verletzungen und Schäden
· Niemals
den
Druckkopf,
Motor
oder
die
Schneidklinge
berühren.
Dabei
besteht
Verletzungsgefahr.
· Bei Einschalten oder sofort nach dem Drucken keine elektrischen oder beweglichen Teile, wie
z.B. Antrieb, Motor, Innengetriebe etc. berühren. Sie können sehr heiß werden und
Verbrennungen verursachen.
· Darauf achten, körperliche Verletzungen und die Beschädigung anderer Objekte durch scharfe
Kanten zu vermeiden.
· Bei Auftreten jeglicher Störungen während des Betriebs den Drucker sofort ausschalten, und
das Netzkabel aus der Steckdose ziehen.
· Nur qualifiziertes Kundendienstpersonal ist zum Zerlegen oder Reparieren des Drucker befugt.
· Die Beseitigung von Betriebsstörungen ist qualifiziertem Fachpersonal zu überlassen. Niemals
versuchen, das Gerät eigenhändig zu zerlegen.
· Beim Öffnen/Schließen der Druckerabdeckung usw. darauf achten, nicht Hände oder Finger
einzuklemmen.
· Nach der Verwendung das Gerät mit dem Netzschalter ausschalten und den Netzstecker aus
der Steckdose ziehen.
99
CITIZEN
CBM-270 User’s Manual
TÄGLICHE WARTUNG
UNG
· Bei der Wartung immer den Netzschalter des Druckers auf Aus stellen und den Stecker aus der
Steckdose ziehen.
· Schmutz und Staub mit einem trockenen, weichen Tuch vom Druckergehäuse abwischen. Bei
starker Verschmutzung einen Lappen in Wasser anfeuchten, auswringen und damit abwischen.
Hierzu niemals flüchtige organische Lösungsmittel, wie z.B. Alkohol, Terpentin, Trichlorethan,
Benzol, Keton oder chemische Staubentfernungsmittel, verwenden.
· Papierstaub mit einer weichen Bürste vom Gehäuse entfernen. Darauf achten, nicht den
Druckkopf zu beschädigen.
VORSICHT:
Druckkopf und Motor werden sehr heiß. Diese Teile nicht sofort nach dem Drucken berühren.
Nicht die Heizfläche des Kopfes mit bloßer Hand oder Metall berühren.
· Reinigen des Druckkopfes
1. Die Druckwalzeneinheit unter Beachtung der Anweisungen in "4.5 Beheben von
Papierstau" entfernen.
2. Den Staub von der Oberfläche der Heizeinheit mit einem mit Äthylalkohol getränkten
Wattetupfer abwischen.
3. Die Druckwalzeneinheit wieder anbringen.
VORSICHT:
Die Wartung nicht direkt nach dem Drucken ausführen, da Druckkopf und Motor sich beim
Betrieb stark erhitzen.
Nicht die Oberfläche der Heizeinheit des Druckkopfes mit der bloßen Hand oder mit
Metallgegenständen berühren. Beim Abnehmen oder Wiederanbringen der Druckwalze
immer den Druckkopf anheben; andernfalls könnten die Teile beschädigt werden. Die
ausgebaute Druckwalzeneinheit vorsichtig zu behandeln, um Schäden zu vermeiden.
100
CITIZEN
CBM-270 User’s Manual
4.
4 .1
BETRIEB
Anschlie
ließen des Netzteils
ils
1. Das Gerät ausschalten.
2. Den Kabelstecker des Netzteils in den Betriebsstromeingang an der Rückseite des Druckers
einstecken.
3. Das Netzkabel des Netzteils zwischen Netzteil und Netzstecker anschließen.
VORSICHT:
1) Nur das vorgeschriebene Netzteil verwenden.
2) Beim Anschließen/Abtrennen des Steckers vom Netzteil immer am Stecker und nicht am
Kabel anfassen.
3) Das Netzteil von anderen rauscherzeugenden Geräten getrennt anschließen.
4) Durch starkes Ziehen am Netzkabel dann dieses beschädigt werden, was zu Bränden,
elektrischen Schlägen oder Reißen führen kann.
5) Bei Gewitter das Netzteil vom Netz trennen und nicht den Drucker betreiben, da sonst die
Gefahr von Bränden oder elektrischen Schlägen besteht.
6) Das Netzkabel nicht in der Nähe von Heizkabeln verlegen. Die Ummantelung könnte
schmelzen und zu Bränden oder elektrischen Schlägen führen.
7) Den Drucker immer an gut gelüfteten Orten betreiben, denn das Netzteil erwärmt sich beim
Betrieb.
8) Immer nur an eine geeignete Netzstromquelle anschließen. Sicherstellen, daß die Steckdose
ausreichende Kapazität hat. Bei unzureichender Kapazität besteht die Gefahr von Bränden
durch Erhitzung.
9) Nach der Verwendung des Druckers oder wenn das Gerät längere Zeit über nicht verwendet
werden soll immer aus Sicherheitsgründen, Netzstecker abziehen.
101
CITIZEN
CBM-270 User’s Manual
4 .2
Anschlie
ließen des Schni
hnitts
ttstelle
llenkabels
1. Das Gerät ausschalten. (Paßseite eingeschlossen)
2. Die Ober- und Unterseite der Kabelkontakte prüfen, und an den Schnittstellenkontakt
anschließen.
3. Die Kabelkontakte befestigen. Serielle Schnittstelle: Die Schrauben zum Befestigen
festziehen. Parallelschnittstelle: Einen Befestigungsring zum Befestigen in Pfeilrichtung
drehen.
4. Das Kabel an den Hostcomputer anschließen.
VORSICHT:
1) Unter bezug auf "6. PARALLELE SCHNITTSTELLE" und "7. SERIELLE SCHNITTSTELLE"
die Pinbelegung von Schnittstellenbuchse und -kabel prüfen. Falsche Verdrahtung kann zu
Störungen oder Fehlfunktionen nicht nur am Drucker sondern auch am Hostcomputer führen.
2) Beim Abtrennen/Anschließen des Schnittstellenkabels immer am Stecker halten. Durch
Ziehen am Kabel selber können Drahtverbindungen beschädigt werden.
3) Immer das Schnittstellenkabel sicher befestigen. Andernfalls kann gute Kommunikation
aufgrund von Verbindungsfehlern nicht erzielt werden.
102
CITIZEN
CBM-270 User’s Manual
4 .3
Einsetzen des Papiers
VORSICHT:
1) Immer die vorgeschriebene Papierrolle verwenden.
2) Bei Verwendung von nicht vorschriftsgemäßem Papier kann die Druckqualität, die
Lebensdauer des Druckkopfes usw. nicht garantiert werden.
3) Nicht Thermalpapier verwenden, wenn der Drucker für Etikettenpapier eingerichtet ist und
umgekehrt. Dadurch können Fehlfunktionen am Drucker oder Schäden am Druckkopf erzeugt
werden.
1. Die Konvexfläche hinten an der Druckerabdeckung halten und nach oben heben.
2. Die Vorderseite der Papierrolle fast im rechten Winkel halten.
VORSICHT:
1) Die Druckerabdeckung ist nicht stationär (öffnen/schließen). Nach dem Abnehmen
sicherstellen, daß sie nicht verlorengeht oder beschädigt wird.
2) Keine ausgefransten oder umgeknickten Papierenden der Papierrolle einsetzen, da dies zu
Papierstau oder Einzugfehlern führen kann.
3) Sicherstellen, daß das Gerät eingeschaltet ist.
4) Den Kopfanhebe-Hebel zu dieser Seite ziehen, um den Druckkopf anzuheben.
5) Wenn sich weiteres Papier auch nach der Papier-Verbraucht-Anzeige im Gerät befindet, die
Papierrolle entfernen, wie im Kapitel "4.4 Entnehmen der eingesetzten Papierrolle"
beschrieben.
6) Die Vorderkante der Papierrolle gerade in den Papiereinzugschacht einsetzen.
7) Die Papierrolle fest in den Papierhalter setzen.
8) Den Kopfanhebe-Hebel zurückschieben. Die Papierrolle wird automatisch durch die Druckwalze
eingezogen, um eine konstante Papiermenge vorzuschieben. (Wenn Auto-Laden aktiviert ist.) (Für
Etikettenpapier wird es bis zur Druck-Startposition am 2. Blatt eingezogen.)
9) Die Druckerabdeckung anbringen.
VORSICHT:
1) Wenn die Papierrolle schlaff ist, das Papier zurückwickeln, um den Durchhang zu beheben.
2) Wenn die Papierrolle geneigt ist, den Kopfanhebe-Hebel heben, um die Papierrollenposition zu
korrigieren oder die Papierrolle herausnehmen und erneut einsetzen.
3) Nicht die Druckerabdeckung während des Drucks öffnen.
4) Nicht die Papierrolle beim Drucken halten oder drücken, da dies zu Papierstau führen kann.
103
CITIZEN
CBM-270 User’s Manual
5) Wenn das Papier eingesetzt ist, wird der Drucker zum Druck vorbereitet. Beachten Sie, daß
falls Daten im Pufferspeicher verbleiben, der Drucker nach dem Einsetzen des Papiers
automatisch mit dem Druck beginnt.
6) Nicht den Drucker mit entfernenter Abdeckung betreiben, da dies zu Fehlfunktionen oder
Sensorabweichungen führen kann.
4 .4
Entnehmen der eingesetzten Papier rolle
lle
1. Die Druckerabdeckung entfernen.
2. Den Kopfanhebe-Hebel heben.
3. Vorsichtig das Papier zur nahen Seite herausziehen. Wenn die Papierrolle verbleibt, vor
dem Herausziehen kurz vor dem Papiereinführschacht abschneiden.
VORSICHT:
1) Nicht die Papierrolle in gegenrichtung ziehen.
2) Wenn dies bei Etikettenpapier ausgeführt wird, können sich die Etiketten lösen.
3) Niemals das Papier mit gesenktem Kopfanhebe-Hebel herausnehmen, da der Druckkopf
beschädigt werden könnte.
4) Der Druckermechanismus kann sich beim Drucken stark erhitzen, deshalb muß vorsichtig
gearbeitet werden.
104
CITIZEN
CBM-270 User’s Manual
4 .5
Beseitigen von Papierstau
1. Das Gerät ausschalten.
2. Die Druckerabdeckung entfernen.
3. Die Papierrolle in der Nähe des Papiereinzugschachts abschneiden.
4. Den Kopfanhebe-Hebel anheben.
5. Die blauen Hebel an beiden Seiten der Druckwalzeneinheit heben, um die Einheit
vorsichtig zu entfernen.
Die Druckwalzeneinheit kann durch manuelles Anheben der
blauen Hebel abgenommen werden.
6. Die restlichen Papierrolle vollständig aus dem Papierpfad entfernen.
7. Wenn Etikettenpapier verwendet wird, können Klebstoffreste haftenbleiben. Einen weichen
Lappen in Alkohol tauchen und Reste sorgfältig abwischen, um nicht den Druckkopf zu
beschädigen.
8. Unter Bestätigung der Richtung der Druckwalzeneinheit diese in den Mechanismus einsetzen.
Die blauen Hebel an beiden Seiten der Einheit zum Befestigen nach unten schieben.
9. Den Kopfanhebe-Hebel absenken.
VORSICHT:
1) Diese Arbeit nicht sofort nach dem Drucken ausführen, da sich der Druckkopf stark erhitzt.
2) Beim Abnehmen der Druckwalzeneinheit immer das Gerät ausschalten.
3) Beim Entfernen von verbleibendem Papier nicht die Heizoberfläche des Kopfes mit bloßen
Händen oder Metallgegenständen berühren.
4) Nicht die Druckwalzeneinheit entfernen, wenn dies nicht unbedingt erforderlich ist, wie z.B.
zum Beheben von Papierstau.
5) Beim Wiedereinsetzen der Druckwalzeneinheit immer bestätigen, daß sie korrekt angebracht ist.
6) Niemals die Druckwalzeneinheit abnehmen oder anbringen, wenn der Kopfanhebe-Hebel
abgesenkt ist.
105
CITIZEN
CBM-270 User’s Manual
4 .6
FEED-Schalterfunk
unktion
4.6.1
Bei Verwendung von Ther malpapier
Durch Drücken des Schalters wird das Papier um 1 Zeile vorgeschoben. Wenn der Schalter
gedrückt gehalten wird, wird das Papier kontinuierlich vorgeschoben.
4.6.2
Bei Verwendung von Etikette
ttenpapier
Durch Drücken des Schalters wird das Papier um 1 Zeile vorgeschoben. Wenn der Schalter 1
Sekunde oder länger gedrückt gehalten wird, wird das Papier um ein Etikett vorgeschoben.
4.6.3
Bei Ausführ
ühr ung eines Makros
Wenn das ERROR-Lämpchen blinkt, während auf die Ausführung eines Makros gewartet
wird, den FEED-Schalter drücken. Der Wartestatus wird fortgesetzt, bis der Schalter
gedrückt wird.
4.6.4
Wenn das Etikett mi
mit Befehl bis zur Papierschne
hneideposition vorgeschoben wird
Das PAPER-Lämpchen blinkt. Nach dem Abschneiden des Papiers wird durch Drücken des
FEED-Schalters der Anfang des nächsten Etiketts aufgesucht. Der Wartestatus wird
fortgesetzt, bis der Schalter gedrückt wird.
VORSICHT:
Wenn das Etikettenpapier um 1 Zeile durch Drücken des FEED-Schalters vorgeschoben wird,
wird die Kopfposition leicht verschoben. Beachten Sie, daß wenn der Druck in diesem Zustand
gestartet wird, das neue Etikett leicht versetzt gedruckt wird. (Es wird empfohlen, das Papier um
1 Etikett vorzuschieben.)
4 .7
Papierende-Funktion
Wenn das Druckpapier aufgebraucht ist, gibt die parallele Schnittstelle BUSY, FAULT und PE
zum Host aus, und die serielle Schnittstelle gibt DTR aus, um den Druck zu stoppen. Wenn
manche Daten noch im Puffer verbleiben, wird der Druck nach dem Austauschen des Papiers
fortgesetzt. Tauschen Sie das Papier entsprechend den Angaben unter "4.3 Einsetzen des
Papiers" aus. Nach dem Austauschen des Papiers die Ausgaben BUSY (DTR), FAULT, und PE
aufheben. Einzelheiten siehe "4.7 Papierende-Funktion".
106
CITIZEN
CBM-270 User’s Manual
4 .8
Papier mangel-Funktion
Wenn das Papier fast verbraucht ist, informiert der PNE-Sensor den Hostcomputer, daß das
Papier fast verbraucht ist, indem ein Signal ausgegeben wird oder das PAPER-Lämpchen am
Bedienfeld aufleuchet. Das PAPER-Lämpchen leuchtet bedingungslos auf.
1. Wenn der PNE-Sensor erkennt, daß das Papier fast verbraucht ist, leuchtet das PAPERLämpchen auf.
2. Wenn PNE aktiviert ist, gibt die parallele Schnittstelle PE aus. (Standardeinstellung)
3. Drucken ist bis zu 1.5 m erlaubt. (Standardeinstellung) Nach dem Drucken oder Zuführen
des Papiers um einen vorgeschriebenen Betrag gibt die parallele Schnittstelle BUSY und
FAULT aus, und die serielle Schnittstelle gibt DTR aus, um den Druck zu stoppen.
4. Das Papier entsprechend dem Verfahren in "4.3 Einsetzen des Papiers" austauschen.
5. Nach dem Austauschen des Papiers die Ausgaben BUSY (DTR), FAULT und PE aufheben.
(1) Im folgenden eine Liste der Ausgaben, die durch die Papiermangel-Funktion und
Papierende-Funktion gegeben werden. Der Ausgabestatus kann mittels DIP-Schalter oder
Befehl geändert werden.
DS1-1
Status
PNE
Function
OFF
Deaktiviert
ON
Aktiviert
Einstellung der PESignalausgabe über
Befehl
*Wenn PE gewählt ist
Wenn PNE erkannt wird
Wenn PE gewählt ist
*Wenn PE erkannt wird
Wenn PNE erkannt wird
Wenn PE gewählt ist
*Wenn PNE gewählt ist
*Wenn PNE gewählt ist
PE-Ausgabe
BUSY (DTR)/FAULTAusgabe
PAPERLämpchen
*Wenn PE erkannt wird
Wenn PE erkannt wird
Wenn
der
Druck
aufgrund von PNE stoppt
*Wenn
der
Druck
aufgrund von PNE stoppt
*Bei PNE
Bei PNE
Bei PNE
*Bei PNE
Markierung* : Standardeinstellung
PNE : Papiermangel PE : Papierende
(2) Druckmenge nach Erkennung von PNE
Wenn PNE aktiviert ist, kann eine druckbare Menge nach der PNE-Erkennung eingestellt
werden. PNE wird erkannt, wenn die restliche Menge der Papierrolle etwa 2 bis 3 m
beträgt. (Diese Betrag hängt von der verwendeten Papierqualität, der Papierdicke und der
Betriebsumgebung ab.)
Der Standardwert beträgt 1,5 m. Bis zu 1,5 m können gedruckt werden, nachdem PNE
erkannt wird. Zu diesem Zeitpunkt beträgt bei Verwendung von Papier der empfohlenen
Dicke von ca. 70 mm die Restmenge des Papiers etwa 0,5 bis 1,5 m, wenn der
Druckvorgang stoppt.
Dieser Wert kann über Befehl zwischen 0 und 2.55 m eingestellt werden. Je nach
Betriebsumgebung und Papierqualität einstellen.
Je nach dem Einstellwert kann das Papierende früher erkannt werden (wobei der Druck
stoppt).
Wenn PNE in eingeschaltetem Zustand erkannt wird, wird von diesem Punkt an eine
eingestellte Druckmenge ausgeführt. (Der Standardwert beträgt 1.5 m).
107
CITIZEN
CBM-270 User’s Manual
4 .9
Autoladefunktion
Dieser Drucker hat eine Funktion zur automatischen Papiereinstellung. Wenn der
Papierendesensor, Papiermangelsensor und Kopfanhebe-Hebel aufgehoben werden, wird das
Papier automatisch um eine konstante Menge in ca. 1 Sekunde zugeführt. (Bis zur
Druckstartposition des zweiten Blatts bei Etikettenpapier.)
Um glatten Betrieb zu gewährleisten, den Kopfanhebe-Hebel zuletzt aufheben.
Außerdem kann der DIP-Schalter zum Aktivieren/Deaktivieren der Funktion verwendet
werden. Wenn sie aktiviert ist, wird automatisches Laden nicht ausgeführt. (Bei
Etikettenpapier wird das Papier zur Druckstartposition zugeführt.)
VORSICHT:
1) Wenn der Autoladefunktion aktiviert wird, nicht die Papierrolle berühren, da dadurch ein
Papiereinzugefehler oder einseitiges Einziehen des Papiers verursacht werden kann.
2) Das Papier immer so einsetzen, daß es in Berührung mit der Papiereinzugwalze kommt;
andernfalls kann das Papier nicht eingezogen werden, und der Druckkopf könnte beschädigt
werden.
3) Wenn bei Etikettenpapier die Etikettensektion oder die schwarze Markierung (zwischen den
Etiketten) nicht beim Zuführen des Papiers um eine konstante Menge erkannt werden kann,
leuchtet das ERROR-Lämpchen am Drucker auf, und der Betrieb stoppt, weil ein Papierfehler
erkannt wird.
4.10 Selbstdruckfunktion
Der Drucker hat eine Funktion, um Vorgabedruck auszuführen. Dazu wird das Gerät bei
gedrückt gehaltenem FEED-Schalter eingeschaltet. Jetzt wird die ROM-Version, die Stellung
der DIP-Schalter, die verwendeten Zeichen, der japanische Schriftzeichensatz etc. ausgedruckt.
Nach dem Selbstdruck schaltet der Drucker auf normalen Betriebszustand zurück.
Bei Etikettenpapier wird dieses bis zur Druckstartposition des nächsten Etiketts
vorgeschoben.
VORSICHT:
1) Nicht diese Funktion verwenden, wenn die Papierrolle fast verbraucht ist.
2) Wenn die Etikettenlänge beim Drucken auf Etikettenpapier zu gering ist, wird der Druck über
mehrere Etiketten fortgesetzt.
3) Datenkommunikation ist beim Selbstdruck nicht möglich.
4) Der Druckinhalt ist bei Thermalpapier und Etikettenpapier unterschiedlich.
108
CITIZEN
CBM-270 User’s Manual
4.11
Bedienfeld und Fehleranzeigen
1. POWER-Lämpchen (grün)
Leuchtet beim Einschalten auf.
2. ERROR-Lämpchen (rot), PAPER-Lämpchen (rot)
Zeigen durch Leuchten oder Blinken einen Fehler an.
Fehler
SpeicherprüfungFehler
Anzeige
ERRORLämpchen
AUS
Schnelles
Blinken
EIN
AUS
Kopfüberhitzung
EIN
AUS
Papiermangel
AUS
EIN
Papierende
EIN
Kopfanheben
Warten
auf
Makroausführung
AUS
AUS
Langsames
Blinken
Etikettpapierabschnei
den warten
AUS
EtikettenpapierFehler
EIN
Rückstellen
PAPERLämpchen
Langsames
Blinken
EIN
109
Kann
werden
nicht
rückgestellt
Kopfanhebe-Hebel absenken
Automatische
Rückstellung
durch Temperaturabfall
Nach Druckstopp eine neue
Papierrolle einsetzen.
Eine
neue
Papierrolle
einsetzen
Den FEED-Schalter drücken
Den FEED-Schalter drücken
Für
die
Spezifikationen
geeignetes Papier einsetzen.
CITIZEN
CBM-270 User’s Manual
< Fehler-Einzelheiten >
Kopfanheben
----- Tritt auf, wenn der Kopfanhebe-Hebel angehoben ist. Der Drucker kann
nicht Papier zuführen oder drucken. Die parallele Schnittstelle gibt BUSY
und FAULT aus, und die serielle Schnittstelle gibt DTR aus.
Kopfüberhitzen
----- Wenn die Temperatur des Druckkopfes ansteigt (auf 60°C oder mehr)
wird ein Druckkopftemperatur-Sensor zum Stoppen des Druckens
aktiviert, um den Kopf vor Überhitzung zu schützen. Die parallele
Schnittstelle gibt BUSY und FAULT aus, und die serielle Schnittstelle
gibt DTR aus. Wenn die Temperatur absinkt (auf ca. 55°C) wird der
Druck automatisch fortgesetzt.
Papiermangel
----- Wenn
der
Durchmesser
der
Papierrolle
abnimmt,
reagiert
der
Papiermangel-Sensor, um darauf hinzuweisen, daß die Papierrolle fast
verbraucht ist. (Siehe "4.8 Papiermangel-Funktion".)
Papierende
----- Wenn die Papierrolle verbraucht ist, wird der Papiersensor in der Nähe
des Druckkopfs aktiviert, um den Druck zu stoppen. Siehe "4.7
Papierende-Funktion".
Etikettenpapierfehler----- Tritt
auf,
wenn
Thermalpapier
oder
nicht-vorschriftsmäßiges
Etikettenpapier eingesetzt wird, wenn Etikettenpapier gewählt ist. Die
parallele Schnittstelle gibt BUSY und FAULT aus, und die serielle
Schnittstelle gibt DTR aus.
3. FEED-Schalter
Siehe "4.6 FEED-Schalterfunktion".
110
CITIZEN
CBM-270 User’s Manual
4..1
..12 Rot/Schwarz-Druck (Vorsichtsmaßregeln)
(1) Papiersorten
Das rote und schwarze Zweifarb-Thermalpapier ändert seine Farbe durch Steuerung der am
Thermalkopf angelegten Energie. Es ist grundsätzlich in zwei Typen unterteilt, entsprechend
der Farbentwicklungsreihenfolge. Wählen Sie eine davon entsprechend Ihrer Applikation.
1. Auf Rot basiertes zweifarbiges Thermalpapier (PB670: MITSUBISHI PAPER MILLS)
Rotdruck (Niedrigenergie)
®
Schwarzdruck (Hochenergie)
2. Auf Schwarz basiertes zweifarbiges Thermalpapier (735FA: RICOH)
Schwarzdruck (Niedrigenergie) ®
Rotdruck (Hochenergie)
(2) Hochenergie-Druckrate
Hochenergiedruck (Schwarzdruck auf rot-basiertem Papier oder Rotdruck auf schwarzbasiertem Papier) erfordert die Anwendung von hoher Energie am Thermalkopf. Zum
Schutz der Lebensdauer des Thermalkopfes verwenden Sie die folgende Druckrate als
Richtlinie; verwenden Sie die Festteilungs (6-Teilung) Methode.
1. Kontinuierlicher Druck mit nur hoher Energie : 6% oder weniger
2. Gemischter kontinuierlicher Druck mit niedriger und hoher Energie
: 30% oder weniger der Standarddruckrate
von 12.5%
3. Druckrate pro Punktzeile
: 50% oder weniger
(3) Minimale Punkte für Hochenergiedruck
Wenn Hochenergiedruck verwendet wird, ist der empfohlene minimale Bereich 3 Punkte
(Länge) ´ 3 Punkte (Breite) oder mehr. Je nach der eingestellten Druckdichte, des
verwendeten Papiers oder der Druckzeichen kann eine ausreichende Änderung des
Farbtons auch bei Hochenergiedruck nicht erzielt werden.
(Zeichen wie [, !, ', (, ¡, - Schriftart B mit kleiner Punktmatrix)
Es wird empfohlen, bei solchen Druckaufgaben doppelbreite Zeichen und doppelhohe
Zeichen zu verwenden.
VORSICHT
1) Wenn Hochenergiedruck kontinuierlich bei hoher Umgebungstemperatur ausgeführt wird,
erhitzt sich der Thermalkopf schneller, und die Schutzschaltung wird aktiviert, so daß der
Druck häufiger gestoppt wird.
Beachten Sie immer die Arbeitstemperatur und Druckrate.
2) Wenn eine Strichcode auf dem 2-Farb-Papier gedruckt wird, können beide Farben im
Normaldruck erscheinen, und der Hochenergiedruck oder der Strichcode können nicht richtig von
einem Strichcodeleser gelesen werden. Bei der Arbeit mit 2-Farbenpapier dies immer beachten.
3) Nicht normalen Hochenergiedrucka auf Einzelfarbpapier (normalem Thermalpapier)
ausführen. Dadurch kann die Lebensdauer des Thermalkopfs oder die Druckqualität
beeinrächtigt werden.
4) Zur Einstellung siehe Befehle (DC3: Switching the Red/Black Printing)
111
CITIZEN
CBM-270 User’s Manual
5.
5 .1
DIP-SCHALTEREINSTELLUN
LLUNG
UNG
Lage der DIP-Schalter
1. Das Gerät ausschalten.
2. Die Druckerabdeckung entfernen, und die Papierrolle herausnehmen. (Der Schalter
befindet sich unter der Papierrolle.)
3. Es gibt 2 Schalter (8polig und 4polig) für die serielle Schnittstelle, und 1 Schalter (8polig)
für die parallele Schnittstelle.
5 .2
DIP-Schalterfunk
unktion
DS1 No.
1
2
3
4
5
6
7
8
Funktion
PNE-Wahl
CR-Umschalten
ON
Aktiviert
LF-Betrieb
OFF
Deaktiviert
Ignoriert
Beim Versand
ON
OFF
Beim Versand
ON
OFF
OFF
Druckdichte
Siehe Tabelle 1
OFF
Papierwahl
Etikettenpapier Thermalpapier
OFF
Autoladen
Aktiviert
Deaktiviert
ON
DTR/DSR, XON/XOFF
XON/XOFF
DTR/DSR
OFF
Japanische Schriftcode-Wahl
S-JIS
JIS
OFF
* DS1-7 : Nur für serielle Schnittstelle aktiviert. Für parallele Schnittstelle deaktiviert.
DS2 (Nur für serielle Schnittstelle)
No.
Funktion
1
2 Einstellung für Baudrate
3 und Parität
4
Tabelle 1
Tabelle 2
Siehe Tabelle 2
OFF
OFF
OFF
OFF
Leicht
OFF
OFF
Standard
ON
OFF
Leicht Dunkel
DS1-3
DS1-4
OFF
ON
Dunkel
ON
ON
DS2-4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
DS2-3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
DS2-2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
DS2-1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Parität
Keine
Keine
Keine
Keine
Keine
Keine
Ungerade
Ungerade
Ungerade
Ungerade
Ungerade
Gerade
Gerade
Gerade
Gerade
Gerade
112
Baudrate
9,600 bps
1,200
2,400
4,800
9,600
19,200
1,200
2,400
4,800
9,600
19,200
1,200
2,400
4,800
9,600
19,200
CITIZEN
CBM-270 User’s Manual
5 .3
Jumperdraht-Funktion
Die Jumperdrähte sind werksseitig vor dem Versand eingestellt. Die folgende Liste zeigt die
grundlegende Einstellung beim Versand. Prüfen Sie die Einstellungen mit dem Selbsttest.
Jumperdrähte
No.
J1
J2
J3
J4
J5
J6
Funktion
Kurz
Internationale Zeichen
Siehe Tabelle 3
Datenbitlänge
Nicht verwendet
Etikett-Erkennung
J7
J8
Nicht verwendet
KommunikationsfehlerMarkierung
* J4
Offen
7 Bit
Schwarze
Markierung
-
8 Bit
Etiketten-Abs
tand
-
Ignoriert
"?" gedruckt
Bei
Versand
Kurz
Kurz
Kurz
Offen
Offen
Offen
Offen
Offen
: Nur serielle Schnittstelle. Für parallele Schnittstelle deaktiviert.
* J5 bis J7 : Nicht die werksseitigen Einstellungen verändern.
Tabelle 3
No.
USA
J1
J2
J3
Kurz
Kurz
Kurz
Frankreich Deutschland
Offen
Kurz
Kurz
Kurz
Offen
Kurz
Großbrita
nnien
Dänemark
-I
Schweden
Italien
Japan
Offen
Offen
Kurz
Kurz
Kurz
Offen
Offen
Kurz
Offen
Kurz
Offen
Offen
Offen
Offen
Offen
VORSICHT:
1) Niemals die Stellungen der Jumperdrähte ändern.
2) Wenn die Einstellungen verändert werden sollen, vorher die Vertretung des Herstellers
kontaktieren.
3) Niemals das Gehäuse des Druckers zerlegen. Dadurch können Betriebsstörungen und andere
Probleme hervorgerufen werden.
113
CITIZEN
CBM-270 User’s Manual
9.
WARTUNG
UNG UND DIENST
Bitte wenden Sie sich an die folgenden Stellen für weitergehende Informationen.
Nordamerika
Andere Gebiete
CBM America Corporation
Japan CBM Corporation
Service Center
Information Systems Division
365 Van Ness Way
1-1-7 Okubo Shinjuku-ku
Suite 510
Tokyo 169-8553 Japan
Torrance, CA 90501, USA
TEL +1-310-781-1460
TEL +81-3-3200-6970
FAX +1-310-781-9157
FAX +81-3-3200-6297
114
CITIZEN