Cisco Systems 7304 Network Router User Manual

CH A P T E R
3
MIB Specifications
This chapter describes each Management Information Base (MIB) on the Cisco 7304 router. Each
description lists any constraints about how the MIB is implemented on the Cisco 7304 router platform.
Unless noted otherwise, the Cisco 7304 implementation of a MIB follows the standard. Any objects not
listed in a table are implemented as defined in the MIB. For detailed MIB descriptions, see the MIB.
Note
Not all MIBs included in a Cisco IOS software release are fully supported by the router. Some MIBs are
not supported at all. Other MIBs might work, but they have not been tested on the router. In addition,
some MIBs are deprecated but cannot be removed from the software. The fact that the MIB is included
in the image does not necessarily mean it is supported by the Cisco 7304 platform.
Note
The RFC versions are listed to show the MIB versions we support.
Table 3-1 lists the MIBs included in Cisco IOS Release 12.2SB that are supported and verified for
configurations on the Cisco 7304 router.
Table 3-1
Supported and Verified Cisco 7304 MIBs
ATM-MIB (RFC 1695)
CISCO-SONET-MIB
BGP4-MIB
CISCO-SYSLOG-MIB
CISCO-AAL5-MIB
CISCO-TC
CISCO-ACCESS-ENVON-MIB
CISCO-TCP-MIB
CISCO-ATM-EXT-MIB
ENTITY-MIB (RFC 2737)
CISCO-BGP-POLICY-ACCOUNTING-MIB
ETHERLIKE-MIB (RFC 2665)
CISCO-BULK-FILE-MIB
EVENT-MIB (RFC 2981)
CISCO-CDP-MIB
EXPRESSION-MIB
CISCO-CLASS-BASED-QOS-MIB
IF-MIB (RFC 2233)
CISCO-CONFIG-COPY-MIB
MPLS-LDP-MIB
CISCO-CONFIG-MAN-MIB
MPLS-LSR-MIB
CISCO-ENTITY-ALARM-MIB
MPLS-TE-MIB
CISCO-ENTITY-ASSET-MIB
MPLS-VPN-MIB
CISCO-ENTITY-EXT-MIB
NOTIFICATION-LOG-MIB
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-1
Chapter 3
Table 3-1
MIB Specifications
Supported and Verified Cisco 7304 MIBs (continued)
CISCO-ENTITY-FRU-CONTROL-MIB
OLD-CISCO-CHASSIS-MIB
CISCO-ENTITY-PFE -MIB
OLD-CISCO-CPU-MIB
CISCO-ENTITY-SENSOR-MIB
OLD-CISCO-INTERFACES-MIB
CISCO-ENTITY-VENDORTYPE-OID-MIB
OLD-CISCO-IP-MIB
CISCO-ENVMON-MIB
OLD-CISCO-MEMORY-MIB
CISCO-FLASH-MIB
PIM-MIB (RFC 2934)
CISCO-FRAME-RELAY-MIB
RFC1213-MIB (MIB II)
CISCO-FTP-CLIENT-MIB
RFC1243-MIB (AppleTalk)
CISCO-HSRP-EXT-MIB
RFC1253-MIB (OSPF)
CISCO-HSRP-MIB
RFC1315-MIB (FRAME RELAY MIB)
CISCO-IETF-IP-MIB
RFC1406-MIB (DS1)
CISCO-IMAGE-MIB
RFC1407-MIB (DS3)
CISCO-IP-STAT-MIB
RFC2558-MIB (SONET MIB)
CISCO-MEMORY-POOL-MIB
RMON-MIB (RFC 1757)
CISCO-NETFLOW-MIB
UDP-MIB (RFC 2013)
CISCO-PING-MIB
SNMP-FRAMEWORK-MIB (RFC 2571)
CISCO-PROCESS-MIB
SNMPv2-MIB (RFC 1907)
CISCO-PRODUCTS-MIB
SNMP-NOTIFICATION-MIB (RFC 2573)
CISCO-QUEUE-MIB
SNMP-TARGET-MIB (RFC 2573)
CISCO-RF-MIB
SNMP-USM-MIB (RFC 2574)
CISCO-RTTMON-MIB
SNMP-VACM-MIB (RFC 2575)
CISCO-SMI
CISCO-CEF-MIB
Table 3-2 lists the Cisco 7304 MIBs included in c7304 image, but support is not verified in the
Cisco 7304 router.
Table 3-2
Cisco 7304 Router MIBs—Support Not Verified in the c7304 Image
ATM-FORUM-ADDR-REG-MIB
CISCO-SNADLC-CONV01-MIB
ATM-FORUM-MIB
CISCO-SNAPSHOT-MIB
BRIDGE-MIB (RFC 1493)
CISCO-STUN-MIB
CISCO-AAA-SESSION-MIB
CISCO-VINES-MIB
CISCO-ALPS-MIB
DLSW-MIB
CISCO-ASPP-MIB
FUNI-MIB
CISCO-BCP-MIB
HC-RMON-MIB
CISCO-BGP4-MIB
IGMP-MIB
CISCO-BSC-MIB
INT-SERV-GUARANTEED-MIB
CISCO-BSTUN-MIB
INT-SERV-MIB
CISCO-BUS-MIB
LAN-EMULATION-CLIENT-MIB
Cisco 7304 Router MIB Specifications Guide
3-2
OL-4925-02
Chapter 3
MIB Specifications
ATM-MIB
Table 3-2
Cisco 7304 Router MIBs—Support Not Verified in the c7304 Image (continued)
CISCO-CAR-MIB
MPOA-MIB
CISCO-CASA-FA-MIB
MSDP-MIB
CISCO-CASA-MIB
NOVELL-IPX-MIB
CISCO-CIRCUIT-INTERFACE-MIB
NOVELL-NLSP-MIB
CISCO-DLCSW-MIB
NOVELL-RIPSAP-MIB
CISCO-DLSW-EXT-MIB
OLD-CISCO-APPLETALK-MIB
CISCO-DLSW-MIB
OLD-CISCO-DECNET-MIB
CISCO-DSPU-MIB
OLD-CISCO-NOVELL-MIB
CISCO-FRAS-HOST-MIB
OLD-CISCO-SYSTEM-MIB
CISCO-IETF-ATM2-PVCTRAP-MIB
OLD-CISCO-TCP-MIB
CISCO-IETF-IP-FORWARD-MIB
OLD-CISCO-TS-MIB
CISCO-IPMROUTE-MIB
OLD-CISCO-VINES-MIB
CISCO-LEC-DATA-VCC-MIB
OLD-CISCO-XNS-MIB
CISCO-LEC-EXT-MIB
RFC1231-MIB (Token Ring MIB)
CISCO-LECS-MIB
RFC1381-MIB (X.25 LAPB)
CISCO-LES-MIB
RFC1382-MIB (X.25 Packet Layer)
CISCO-MPOA-EXT-MIB
RFC2006-MIB (MIP)
CISCO-NDE-MIB
RMON2-MIB
CISCO-NTP-MIB
RS-232-MIB
CISCO-PIM-MIB
RSVP-MIB
CISCO-QLLC01-MIB
SMON-MIB
CISCO-RMON-SAMPLING-MIB
SNA-SDLC-MIB
CISCO-RSRB-MIB
SNMP-PROXY-MIB
CISCO-SDLLC-MIB
SOURCE-ROUTING-MIB
CISCO-SLB-EXT-MIB
TCP-MIB (RFC 2012)
CISCO-SLB-MIB
CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
ATM-MIB
The ATM-MIB (RFC 1695) contains the ATM and ATM adaptation layer 5 (AAL5) objects used to
manage logical and physical entities and the relationship between them, such as ATM interfaces, virtual
links, cross connects, and AAL5 entities and connections.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-3
Chapter 3
MIB Specifications
ATM-FORUM-ADDR-REG-MIB
Table 3-3 lists the constraints that the Cisco 7304 router places on objects in the ATM-MIB. For detailed
definitions of MIB objects, see the MIB.
Table 3-3
ATM-MIB Constraints
MIB Object
Notes
atmInterfaceDs3PlcpTable
Not used in Cisco 7304.
atmInterfaceTCTable
Not supported.
atmTrafficDescrParamTable
Read-only.
atmVplTable
Not supported.
atmVclTable
•
atmVclAdminStatus
Read-only.
•
atmVclReceiveTrafficDescrIndex Read-only.
•
atmVclTransmitTrafficDescrIndex Read-only.
•
atmVccAalType
•
atmVccAal5CpcsTransmitSduSize Read-only. Default value 4470.
•
atmVccAal5CpcsReceiveSduSize Read-only. Default value 4470.
•
atmVccAal5EncapsType
Read-only.
•
atmVclCrossConnectIdentifier
Read-only.
•
atmVclRowStatus
Read-only.
•
atmVclCastType
Not supported.
•
atmVclConnKind
Not supported.
Read-only.
atmVpCrossConnectTable
•
atmVcCrossConnectIndexNext
atmVcCrossConnectTable
Not supported.
Not implemented.
aal5VccTable
•
atmTrafficDescrParamIndexNext
Not supported.
1 The SAR used in the OSM-2-OC-12-ATM-xx+ card does not support the CRC error counters, timeout counter,
and oversized SDUs statistics in the aal5VccTable. These statistics are supported in the PA-A3-OC-3-SMI card.
2 The ifType for the ifIndex used in the ATM-MIB tables must be of type atm(37).
ATM-FORUM-ADDR-REG-MIB
The ATM-FORUM-ADDR-REG-MIB contains information about ATM user-network interface (UNI)
addresses and ports. The MIB also contains ATM address registration administration information.
There are no constraints on this MIB.
ATM-FORUM-MIB
The ATM-FORUM-MIB contains ATM object definitions and object identifiers (OIDs).
Cisco 7304 Router MIB Specifications Guide
3-4
OL-4925-02
Chapter 3
MIB Specifications
BGP4-MIB
BGP4-MIB
The BGP4-MIB (RFC 1657) provides access to information related to the implementation of the Border
Gateway Protocol (BGP). The MIB provides:
•
BGP configuration information
•
Information about BGP peers and messages exchanged with them
•
Information about advertised networks
BRIDGE-MIB
The BRIDGE-MIB contains objects to manage Media Access Control (MAC) bridges between Local
Area Network (LAN) segments, as defined by the IEEE 802.1D-1990 standard. This MIB is extracted
from RFC 1493 and is intended for use with network management protocols in TCP/IP-based internets.
CISCO-AAA-SESSION-MIB
The CISCO-AAA-SESSION-MIB contains information about accounting sessions based on
authentication, authorization, and accounting (AAA) protocols.
CISCO-AAL5-MIB
The CISCO-AAL5-MIB contains performance statistics for ATM adaptation layer 5 (AAL5) virtual
channel connections (VCCs). This MIB provides statistics not found in the aal5VccTable in RFC 1695
(for example, packets and octets received and transmitted on the VCC).
There are no constraints on this MIB.
CISCO-ACCESS-ENVMON-MIB
The CISCO-ACCESS-ENVMON-MIB indicates the reason for a power supply failure, which is
information that is not provided in the ciscoEnvMonSupplyStatusTable in the CISCO-ENVMON-MIB.
The CISCO-ACCESS-ENVMON-MIB also defines temperature and voltage notifications to replace
those in CISCO-ENVMON-MIB.
CISCO-ALPS-MIB
The CISCO-ALPS-MIB provides Cisco airline protocol support for IBM-P1024B(ALC) and
Unisys-P1024C(UTS) protocol encapsulation over TCP/IP. The MIB contains configuration and
operational information for the protocol, which provides a tunneling mechanism to transport airline
protocol data across a Cisco router-based TCP/IP network to an X.25-attached mainframe.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-5
Chapter 3
MIB Specifications
CISCO-ASPP-MIB
CISCO-ASPP-MIB
The CISCO-ASPP MIB provides configuration and operational information on asynchronous polled
protocols such as the asynchronous security protocols that alarm-monitoring companies use. The
protocols are handled in Pass-through mode. ASPP handles the receiving and sending of asynchronous
blocks.
CISCO-ATM-EXT-MIB
The CISCO-ATM-EXT-MIB contains extensions to the Cisco ATM module that are used to manage
ATM entities. It provides additional AAL5 performance statistics for a virtual channel connection (VCC)
on an ATM interface.
Note
There are no constraints on this MIB and the ATM-EXT-MIB has only one table. The cAal5VccExtTable
augments the aal5VccTable of the ATM-MIB. The aal5VccTable contains additional AAL5 performance
parameters.
CISCO-BCP-MIB
The CISCO-BCP-MIB (based on RFC 2878) (Bridging Control Protocol) contains objects to configure,
enable, and disable bridge modules on both ends of point-to-point links. The Cisco 7304 router uses the
BCP for transporting Ethernet frames over SONET and DPT networks. The BCP-MIB manages and
monitors Bridge Control Protocol configuration and information on subnetwork interfaces using the
family of Point-to-Point Protocols.
The CISCO-BCP-MIB contains the following tables:
•
bcpOperTable—Describes the current operational status information for a particular link. For all
entries in ifTable with ifType ppp(23), there will be an entry in this table.
•
bcpConfigTable—Shows the BCP configuration information (for example, the current configuration
for spanning tree, line identification option).
Table 3-4 lists the constraints that the router places on objects in the CISCO-BCP-MIB. Also see the table of
new MIB objects which follows. For detailed definitions of MIB objects, see the MIB.
Table 3-4
CISCO-BCP-MIB Constraints
MIB Object
Notes
bcpOperTable
•
bcpOperStatus
Possible values:
open(1)
closed (2)
listening(3)
bcpConfigTable
•
bcpConfigBridgeIdControl
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigLineIdControl
Read-only. Possible values: enabled(1), disabled(2)
Cisco 7304 Router MIB Specifications Guide
3-6
OL-4925-02
Chapter 3
MIB Specifications
CISCO-BGP-POLICY-ACCOUNTING-MIB
Table 3-4
CISCO-BCP-MIB Constraints (continued)
MIB Object
Notes
•
bcpConfigMacSupport
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigTinygram
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigMacAddressControl
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigSpanTreeControl
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigIeee802dot1qTagged
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigMgmtInline
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigBCPacketIndicator
Read-only. Possible values: enabled(1), disabled(2)
•
bcpConfigBridgeId
Read-only.
•
bcpConfigLineId
Read-only.
•
bcpConfigMacType
Read-only.
•
bcpConfigMacAddress
Read-only.
•
bcpConfigSpanTree
Read-only.
1 bcpConfigTable objects are defined as read-write; but they are implemented as READ-ONLY.
2 The CISCO-BCP-MIB supports interfaces configured with bridge-enabled only, which means if no “bridge-enable” is
configured,there is no entry for this interface when the user pulled the bcpOperTable or bcpConfigTable by SNMP.
CISCO-BGP-POLICY-ACCOUNTING-MIB
The CISCO-BGP-POLICY-ACCOUNTING-MIB contains BGP policy-based accounting information
(such as ingress traffic on an interface), which can be used for billing purposes. The MIB provides
support for BGP Policy Accounting, which enables you to classify IP traffic into different classes and to
maintain statistics for each traffic class.
The MIB contains counts of the number of bytes and packets of each traffic type on each input interface.
This information can be used to charge customers according to the route that their traffic travels.
CISCO-BGP4-MIB
The BGP4-MIB provides access to information related to the implementation of the Border Gateway
Protocol (BGP). The MIB provides:
•
BGP configuration information
•
Information about BGP peers and messages exchanged with them
•
Information about advertised networks
CISCO-BSC-MIB
The CISCO-BSC-MIB contains objects to manage binary synchronous communications (BSC) on the
router, including BSC ports (serial interfaces) and BSC control units (stations on a port).
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-7
Chapter 3
MIB Specifications
CISCO-BSTUN-MIB
CISCO-BSTUN-MIB
The CISCO-BSTUN-MIB contains objects to manage Block Serial Tunnels (BSTUNs) on the router.
The MIB provides global BSTUN information and contains configuration and operational information
to manage BSTUN groups, ports, and routes.
CISCO-BULK-FILE-MIB
The CISCO-BULK-FILE-MIB contains objects to create and delete files of SNMP data for bulk-file
transfer.
CISCO-BUS-MIB
The CISCO-BUS-MIB contains information to manage LANE broadcast and unknown servers.
CISCO-CAR-MIB
The CISCO-CAR-MIB contains information about the Committed Access Rate (CAR) assigned to router
interfaces. The CAR is used to control the rate of traffic on an interface for packet switching purposes.
The MIB provides information about how the router is to handle traffic that conforms and exceeds the
CAR on the interface.
CISCO-CASA-FA-MIB
The CISCO-CASA-FA-MIB is used in conjunction with the CISCO-CASA-MIB to manage a
Cisco Appliance Services Architecture (CASA) forwarding agent (FA).
The CASA protocol allows appliances (software entities such as web caches, firewalls, and load
balancers) to control the behavior of forwarding agents (hardware devices such as switches and routers).
The appliance tells forwarding agents how to handle packets based on their source and destination
IP addresses and ports, and IP protocol fields (this information is called an affinity).
CISCO-CASA-MIB
The CISCO-CASA-MIB contains objects to manage a Cisco Appliance Services Architecture (CASA)
entity (such as a manager or a forwarding agent). The MIB contains objects to configure CASA, and to
retrieve status and operational information about the fixed affinity cache.
The CASA protocol allows appliances (software entities such as web caches, firewalls, and load
balancers) to control the behavior of forwarding agents (hardware devices such as switches and routers).
The appliance tells forwarding agents how to handle packets based on their source and destination
IP addresses and ports, and IP protocol fields (this information is called an affinity).
Cisco 7304 Router MIB Specifications Guide
3-8
OL-4925-02
Chapter 3
MIB Specifications
CISCO-CDP-MIB
CISCO-CDP-MIB
The CISCO-CDP-MIB contains objects to manage the Cisco Discovery Protocol (CDP) on the router.
CISCO-CEF-MIB
The CISCO-CEF-MIB (Cisco Express Forwarding) contains objects that manage Cisco Express
Forwarding (CEF) technology. CEF is the key data plane forwarding path for layer 3 IP switching
technology. The CISCO-CEF-MIB monitorS CEF operational data and provideS notification when
encountering errors in CEF, through SNMP.
Note
Cisco Express Forwarding (CEF) is a high speed switching mechanism that a router uses to forward
packets from the inbound to the outbound interface.
CISCO-CIRCUIT-INTERFACE-MIB
The CISCO-CIRCUIT-INTERFACE-MIB contains objects to configure the circuit description for an
interface. The circuit description identifies circuits on interfaces such as ATM and Frame Relay, and
might be used, for example, to correlate performance statistics on the corresponding interfaces.
CISCO-CLASS-BASED-QOS-MIB
The CISCO-CLASS-BASED-QOS-MIB provides access to quality of service (QoS) configuration
information and statistics for Cisco platforms that support the Modular Quality of Service command-line
interface (Modular QoS CLI).
The MIB uses the following indexes to identify QoS features and distinguish among instances of those
features:
•
cbQosPolicyIndex—Identifies a service policy that is attached to a logical interface.
•
cbQosObjectsIndex—Identifies each QoS feature on the Cisco 7304 router.
•
cbQosConfigIndex—Identifies a type of QoS configuration. This index is shared by QoS objects that
have identical configurations.
The indexes cbQosPolicyIndex and cbQosObjectsIndex are assigned by the system to uniquely identify
each instance of a QoS feature. These indexes are never reused between router reboots, even if the QoS
configuration changes.
QoS MIB information is stored in:
•
Configuration objects—Includes all ClassMap, PolicyMap, Match Statements, and Feature Actions
configuration parameters. Might have multiple identical instances. Multiple instances of the same
QoS feature share a single configuration object, which is identified by cbQosConfigIndex.
•
Statistics objects—Includes summary counts and rates by traffic class before and after any
configured QoS policies are enforced. In addition, detailed feature-specific statistics are available
for select PolicyMap features. Each has a unique runtime instance. Multiple instances of a QoS
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-9
Chapter 3
MIB Specifications
CISCO-CLASS-BASED-QOS-MIB
feature have a separate statistics object. Run-time instances of QoS objects are each assigned a
unique identifier (cbQosObjectsIndex) to distinguish among multiple objects with matching
configurations.
Cisco 7304 Router MIB Specifications Guide
3-10
OL-4925-02
Chapter 3
MIB Specifications
CISCO-CLASS-BASED-QOS-MIB
MIB Constraints
Table 3-5 lists the constraints that the Cisco 7304 Network Service Engine (NSE) 100-based router
places on objects in the CISCO-CLASS-BASED-QOS-MIB. For detailed definitions of MIB objects, see
the MIB. Any MIB table or object not listed in this table is implemented as defined in the MIB.
Note
The CISCO-CLASS-BASED-QOS-MIB support for the Cisco 7304 NPE-G100 and the Cisco c7200
NPE-G1 is the same.
Table 3-5
CISCO-CLASS-BASED-QOS-MIB Constraints for the c7304 NSE-100
MIB Object
Notes
cbQosInterfacePolicyTable
•
cbQosInterfacePolicyIndex
Not supported.
cbQosFrameRelayPolicyTable
•
cbQosFRPolicyIndex
Not supported.
cbQosATMPVCPolicyTable
•
cbQosATMPolicyIndex
Not supported.
cbQosQueueingCfgTable
•
cbQosQueueingCfgFlowEnabled·
The QosQueueingCfgFlowEnabled is always false(2)
because the fair queue is not supported.
•
cbQosQueueingCfgIndividualQSize·
Not supported on the NSE-100.
•
cbQosQueueingCfgDynamicQNumber·
Not supported on the NSE-100.
•
cbQosQueueingCfgPrioBurstSize
Not supported on the NSE-100.
cbQosTSCfgTable
•
cbQosTSCfgBurstSize
Not supported on the NSE-100.
•
cbQosTSCfgExtBurstSize
Not supported on the NSE-100.
•
cbQosTSCfgAdaptiveEnabled
Not supported on the NSE-100.
•
cbQosTSCfgAdaptiveRate
Not supported on the NSE-100.
•
cbQosTSCfgLimitType
average(1) is the only value supported on the
NSE-100 card.
cbQosQueueingStatsTable
•
cbQosQueueingCurrentQDepth·
Not supported on the NSE-100.
•
cbQosQueueingMaxQDepth
Not supported on the NSE-100. Current value is
available in Parallel eXpress Forwarding (PXF).
cbQosTSStatsTable
•
cbQosTSStatsDelayedByteOverflow·
•
cbQosTSStatsDelayedByte
•
cbQosTSStatsDelayedByte64
For the NSE-100s, the shaping stats,
cbQosTSStatsEntry, are not supported in PXF*. PXF
performs the traffic shaping according to the traffic
shaping configuration.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-11
Chapter 3
MIB Specifications
CISCO-CONFIG-COPY-MIB
Table 3-5
CISCO-CLASS-BASED-QOS-MIB Constraints for the c7304 NSE-100
MIB Object
•
cbQosTSStatsDelayedPktOverflow
•
cbQosTSStatsDelayedPkt·
•
cbQosTSStatsDelayedPkt64
•
cbQosTSStatsDropByteOverflow
•
cbQosTSStatsDropByte
•
cbQosTSStatsDropByte64
•
cbQosTSStatsActive
•
cbQosTSStatsCurrentQSize
Notes
*PXF is Cisco Parallel eXpress Forwarding (PXF) IP Services Processor technology. The Cisco 7304 router offers two types of
processor options: general-purpose network processing engine (NPE-G100) and hardware-accelerated network services
engine (NSE-100).The NSE-100 is the forwarding engine and route processor for the Cisco 7304. The NSE-100 utilizes
Parallel eXpress Forwarding (PXF) technology to deliver hardware-accelerated network services.
CISCO-CONFIG-COPY-MIB
The CISCO-CONFIG-COPY-MIB contains objects to copy configuration files on the router. For
example, the MIB enables the SNMP agent to:
•
Copy configuration files to and from the network
•
Copy the running configuration to the startup configuration
•
Copy the startup or running configuration files to and from a local Cisco IOS file system
CISCO-CONFIG-MAN-MIB
The CISCO-CONFIG-MAN-MIB contains objects to track and save changes to the router configuration.
The MIB represents a model of the configuration data that exists elsewhere in the router and in peripheral
devices. Its main purpose is to report changes to the running configuration through the
SNMP notification ciscoConfigManEvent.
CISCO-DLCSWITCH-MIB
The CISCO-DLCSWITCH-MIB contains objects to manage Frame-Relay access support (FRAS)
sessions to the end-user station. The MIB applies only to downstream or end-user sessions. It does not
apply to upstream or host-end sessions, which are managed through the FRAS-HOST-MIB.
CISCO-DLSW-EXT-MIB
The CISCO-DLSW-EXT-MIB is an extension to the CISCO-DLSW-MIB. It contains objects to manage
Cisco specific data-link switching (DLSW) protocol enhancements. DLSw provides a way to transport
Systems Network Architecture (SNA) and NetBIOS traffic over an IP network.
Cisco 7304 Router MIB Specifications Guide
3-12
OL-4925-02
Chapter 3
MIB Specifications
CISCO-DLSW-MIB
CISCO-DLSW-MIB
The CISCO-DLSW-MIB contains objects to manage data-link switches.
CISCO-DSPU-MIB
The CISCO-DSPU-MIB contains objects to configure and manage Cisco downstream physical
unit (DSPU) objects.
CISCO-ENTITY-ALARM-MIB
The CISCO-ENTITY-ALARM-MIB enables the Cisco 7304 router to monitor alarms generated by
system components, such as the chassis, slots, modules, power supplies, fans, and ports.
For a component’s alarms to be monitored, the component must be defined by a row in the
entPhysicalTable of the ENTITY-MIB in the “ENTITY-MIB” section on page 3-36 of this guide.
Note
The Cisco 7403 router temperature, power supplies, and fan monitoring are implemented in the
CISCO-ENTITY-SENSOR-MIB instead of the CISCO-ENTITY-ALARM-MIB. The temperature
sensors are supported at the line card level, not the chassis level.
MIB Constraints
Table 3-6 lists the constraints that the Cisco 7304 router places on objects in the
CISCO-ENTITY-ALARM-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-6
CISCO-ENTITY-ALARM-MIB Constraints
MIB Object
Notes
ceAlarmDescrTable
•
ceAlarmDescrSeverity
Read-only.
ceAlarmFilterProfileTable
•
ceAlarmFilterIndex
•
ceAlarmFilterStatus
•
ceAlarmFilterAlias
•
ceAlarmFilterAlarmsEnabled
•
ceAlarmFilterNotifiesEnabled
•
ceAlarmFilterSyslogEnabled
The objects listed are not supported.
ceAlarmCutOff
Not supported.
ceAlarmFilterProfileIndexNext
Not supported.
The MIB table, entPhysicalTable, identifies the physical system components in the router. The following
list describes the table objects for the CISCO-ENTITY-ALARM-MIB:
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-13
Chapter 3
MIB Specifications
CISCO-ENTITY-ALARM-MIB
•
Physical entity—The component in the Cisco 7304 router that generates the alarm.
•
Physical vendor type—The object specifies an identifier (typically an enterprise-specific OID) that
uniquely identifies the vendor type of those physical entities that this alarm description applies to.
•
Alarm severity—Each alarm type defined by a vendor type and employed by the system is assigned
an associated severity:
– Critical—Indicates a severe, service-affecting condition has occurred and that immediate
corrective action is imperative, regardless of the time of day or day of the week. For example,
online insertion and removal of line cards or loss of signal failure when a physical port link is
down.
– Major—Used for hardware or software conditions. Indicates a serious disruption of service or
the malfunctioning or failure of important hardware. Requires immediate attention and response
of a technician to restore or maintain system stability. The urgency is less than in critical
situations because of a lesser effect on service or system performance. For example, a minor
alarm is generated if a secondary NSE-100 or NPE-G100 card fails or it is removed.
– Minor—Used for troubles that do not have a serious effect on service to customers or for alarms
in hardware that are not essential to the operation of the system.
– Info—Notification about a condition that could lead to an impending problem or notification of
an event that improves operation.
The syntax values are: critical(1), major(2), minor(3), info(4)
•
Alarm description text—Specifies a readable message describing the alarm.
•
Alarm type—Identifies the type of alarm that is generated. An arbitrary integer value that uniquely
identifies an event relative to a physical entity in the Cisco 7304 router. Values 0 through 255.
Table 3-7 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities, line
card slots, and processor cards.
Table 3-7
entPhysicalTable Objects for Cisco 7304 Router Line Cards
Physical Entity
entPhysicalVendorType
ceAlarmDesc
rSeverity
ceAlarmDescrText
ceAlarmDescr
AlarmType
Line card slots
cevContainerSlot
critical
Active line card
removed OIR alarm
0
Line card slots
cevContainerSlot
critical
Line card stopped
responding OIR
alarm
1
NSE-100 and
NPE-G100
processor cards
cevCpuC7300Nse100
critical
or
cevCpuC7300Npeg100
Cutover
0
NSE-100 and
NPE-G100
processor cards
cevCpuC7300Nse100
major
or
cevCpuC7300Npeg100
Secondary failure
1
NSE-100 and
NPE-G100
processor cards
cevCpuC7300Nse100
major
or
cevCpuC7300Npeg100
Secondary removed
2
NSE-100 and
NPE-G100
processor cards
cevCpuC7300Nse100
major
or
cevCpuC7300Npeg100
Secondary not
synchronized
3
Cisco 7304 Router MIB Specifications Guide
3-14
OL-4925-02
Chapter 3
MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-8 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entity, the
6-port clear channel T3 (DS3) line card.
Table 3-8
entPhysicalTable Objects for Cisco 7304 Router 6-Port Clear Channel T3 Module Ports
Physical Entity
entPhysicalVendorType
ceAlarmDescr
ceAlarmDescr
Severity
ceAlarmDescrText AlarmType
Clear channel T3
interface
cevPortDs3
major
Transmitter is
sending remote
alarm
0
Clear channel T3
interface
cevPortDs3
major
Transmitter is
sending AIS
1
Clear channel T3
interface
cevPortDs3
major
Receiver has loss
of signal
2
Clear channel T3
interface
cevPortDs3
major
Receiver is
receiving AIS
3
Clear channel T3
interface
cevPortDs3
major
Receiver has loss
of frame
4
Clear channel T3
interface
cevPortDs3
major
Receiver has
remote alarm
5
Clear channel T3
interface
cevPortDs3
major
Physical port link
down
6
Clear channel T3
interface
cevPortDs3
info
Physical port
adminsitrative
state down
7
Table 3-9 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities,
Gigabit Ethernet and Fast Ethernet port adapter cards.
Table 3-9
entPhysicalTable Objects for Cisco 7304 Router Port Adapters
Physical Entity
entPhysicalVendorType
ceAlarmDescr
ceAlarmDescr
Severity
ceAlarmDescrText AlarmType
Gigabit Ethernet
cevPortGE
critical
Physical port link
down
0
Gigabit Ethernet
cevPortGE
info
Physical port
administrative
state down
1
Fast Ethernet
cevPortFEIP
critical
Physical port link
down
0
Fast Ethernet
cevPortFEIP
info
Physical port
administrative
state down
1
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-15
Chapter 3
MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-10 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities,
2 and 4-port OC-3c/STM-1, and 1 and 2-port OC-12c/STM-4 Packet over SONET/SDH line cards.
Table 3-10
entPhysicalTable Objects for Cisco 7304 Router Packet over SONET Line Card Ports
Physical Entity
entPhysicalVendor
Type
ceAlarmDescr
Severity
Packet over SONET
cevPortPOS
critical
Section loss of
signal failure
0
Packet over SONET
cevPortPOS
critical
Section loss of
frame failure
1
Packet over SONET
cevPortPOS
critical
Section out of
frame alignment
2
Packet over SONET
cevPortPOS
critical
Section J0
mismatch
3
Packet over SONET
cevPortPOS
critical
Section bit
interleaved parity
4
Packet over SONET
cevPortPOS
critical
Line alarm
indication signal
5
Packet over SONET
cevPortPOS
critical
Line remote failure 6
indication
Packet over SONET
cevPortPOS
critical
Line bit interleaved 7
parity
Packet over SONET
cevPortPOS
critical
Line far end block
errors
8
Packet over SONET
cevPortPOS
critical
Path alarm
indication signal
9
Packet over SONET
cevPortPOS
critical
Path remote failure 10
indication
Packet over SONET
cevPortPOS
critical
Path loss of pointer 11
Packet over SONET
cevPortPOS
critical
Path bit interleaved 12
parity
Packet over SONET
cevPortPOS
critical
Path far end block
errors
13
Packet over SONET
cevPortPOS
critical
Protection switch
byte failure
14
Packet over SONET
cevPortPOS
critical
Path pointer
justifications
15
Packet over SONET
cevPortPOS
critical
Path positive
pointer stuff event
16
Packet over SONET
cevPortPOS
critical
Path negative
pointer stuff event
17
Packet over SONET
cevPortPOS
critical
Path payload label
mismatch
18
ceAlarmDescrText
ceAlarmDescr
AlarmType
Cisco 7304 Router MIB Specifications Guide
3-16
OL-4925-02
Chapter 3
MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-10
entPhysicalTable Objects for Cisco 7304 Router Packet over SONET Line Card Ports
Physical Entity
entPhysicalVendor
Type
ceAlarmDescr
Severity
Packet over SONET
cevPortPOS
critical
Path payload
unequipped
19
Packet over SONET
cevPortPOS
critical
Count of APS
20
Packet over SONET
cevPortPOS
critical
Receiver data out
of lock failure
21
Packet over SONET
cevPortPOS
critical
Signal failure alarm 22
Packet over SONET
cevPortPOS
critical
Signal degrade
alarm
23
Packet over SONET
cevPortPOS
critical
Threshold cross
alarm–B1
24
Packet over SONET
cevPortPOS
critical
Threshold cross
alarm–B2
25
Packet over SONET
cevPortPOS
critical
Threshold cross
alarm–B3
26
Packet over SONET
cevPortPOS
critical
Port link down
alarm
27
Packet over SONET
cevPortPOS
info
Port administrative 28
down alarm
ceAlarmDescrText
ceAlarmDescr
AlarmType
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-17
Chapter 3
MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-11 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities,
2-port OC-3 ATM line cards.
Table 3-11
entPhysicalTable Objects for Cisco 7304 Router OC-3 ATM Line Cards
Physical Entity
entPhysicalVendorType
ceAlarmDescr
ceAlarmDescr
Severity
ceAlarmDescrText AlarmType
ATM over SONET
cevPortOC3
critical
Loss of signal
failure
0
ATM over SONET
cevPortOC3
critical
Loss of frame
1
ATM over SONET
cevPortOC3
critical
Out of frame
failure
2
ATM over SONET
cevPortOC3
critical
Loss of path
3
ATM over SONET
cevPortOC3
critical
Line far end RX
failure
4
ATM over SONET
cevPortOC3
critical
Line alarm
indication signal
5
ATM over SONET
cevPortOC3
critical
Path alarm
indication signal
6
ATM over SONET
cevPortOC3
critical
Far end receiver
data failure
7
ATM over SONET
cevPortOC3
critical
Loss of cell
delineation
8
ATM over SONET
cevPortOC3
critical
Path bit
interleaved parity
9
ATM over SONET
cevPortOC3
critical
Path payload label 12
mismatch
ATM over SONET
cevPortOC3
critical
Section bit
interleaved parity
10
ATM over SONET
cevPortOC3
critical
Line bit
interleaved parity
11
ATM over SONET
cevPortOC3
critical
Path payload
unequipped
13
ATM over SONET
cevPortOC3
critical
Physical port link
down
14
ATM over SONET
cevPortOC3
Info
Physical port
administrative
state down
15
Cisco 7304 Router MIB Specifications Guide
3-18
OL-4925-02
Chapter 3
MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-12 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities,
1-port enhanced ATM T3, and E3 port adapters.
Table 3-12
entPhysicalTable Objects for Cisco 7304 Router ATM over T3 and E3 Port Adapters
Physical Entity
entPhysicalVendorType
ceAlarmDescr
ceAlarmDescr
Severity
ceAlarmDescrText AlarmType
ATM over T3
cevPortDs3Atm
critical
Loss of signal
failure
0
ATM over T3
cevPortDs3Atm
critical
Out of frame
failure
1
ATM over T3
cevPortDs3Atm
critical
Pay load mismatch 2
ATM over T3
cevPortDs3Atm
critical
Idle
3
ATM over T3
cevPortDs3Atm
critical
Loss of cell
delineation
4
ATM over T3
cevPortDs3Atm
critical
Far end receiver
data failure
5
ATM over T3
cevPortDs3Atm
critical
Alarm indication
signal
6
ATM over T3
cevPortDs3Atm
critical
Physical port link
down
7
ATM over T3
cevPortDs3Atm
info
Physical port
administrative
state down
8
ATM over E3
cevPortE3Atm
major
Loss of signal
failure
0
ATM over E3
cevPortE3Atm
major
Out of frame
failure
1
ATM over E3
cevPortE3Atm
major
Pay load mismatch 2
ATM over E3
cevPortE3Atm
major
Idle
3
ATM over E3
cevPortE3Atm
major
Loss of cell
delineation
4
ATM over E3
cevPortE3Atm
major
Far end receiver
data failure
5
ATM over E3
cevPortE3Atm
major
Alarm indication
signal
6
ATM over E3
cevPortE3Atm
major
Physical port link
down
7
ATM over E3
cevPortE3Atm
info
Physical port
administrative
state down
8
GBIC container
cevContainerGbic or
cevContainerSFP
critical
GBIC is missing
0
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-19
Chapter 3
MIB Specifications
CISCO-ENTITY-ASSET-MIB
CISCO-ENTITY-ASSET-MIB
The CISCO-ENTITY-ASSET-MIB provides asset tracking information for the physical components in
the ENTITY-MIB (RFC 2737) entPhysicalTable. This MIB is applicable to all line and processor cards.
The ceAssetTable contains an entry (ceAssetEntry) for each physical component on the router. Each
entry provides information about the component, such as its orderable part number, serial number,
hardware revision, manufacturing assembly number, and manufacturing revision.
Program most physical components with a standard Cisco generic ID PROM value that specifies asset
information for the component. If possible, the MIB accesses the component’s ID PROM information.
The CISCO-ENTITY-ASSET-MIB contains two object groups:
•
ceAssetGroupRev1—The ceAssetGroupRev1 group holds objects that are not present in the
ENTITY-MIB.
•
ceAssetEntityGroup—The ceAssetEntityGroup duplicates the objects in entPhysicalTable of the
ENTITY-MIB (RFC 2737).
Table 3-13 lists the constraints that the Cisco 7304 router places on objects in the
CISCO-ENTITY-ASSET-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-13
CISCO-ENTITY-ASSET-MIB Object Constraints
MIB Object
Notes
ceAssetTable
ceAssetAlias
Not supported.
ceAssetTag
Not supported.
ceAssetCLEI
Not supported.
The following objects are read-only objects in the MIB definition. You see values if your platform has any related information
on the object. Otherwise, the object is a zero length string, such as ceAssetFirmwareID, ceAssetFirmwareRevision,
ceAssetSoftwareI, and ceAssetSoftwareRevision.
CISCO-ENTITY-EXT-MIB
The CISCO-ENTITY-EXT-MIB contains extensions for the processor modules listed in the
ENTITY-MIB entPhysicalTable. A processor module is any physical entity that has a CPU, RAM, and
NVRAM, and can load a boot image and save a configuration. The extensions in this MIB provide
information such as RAM and NVRAM sizes, configuration register settings, and bootload image names
for each processor module.
The CISCO-ENTITY-EXT-MIB contains two tables:
•
The ceExtPhysicalProcessorTable table contains information related to processor RAM and
NVRAM sizes (total and used).
•
The ceExtConfigRegTable table contains information related to configuration register settings and
boot images.
Table 3-14 lists the constraints that the Cisco 7304 router places on objects in the
CISCO-ENTITY-EXT-MIB. For detailed definitions of MIB objects, see the MIB. Any objects not listed in
this table are implemented as defined in this MIB.
Cisco 7304 Router MIB Specifications Guide
3-20
OL-4925-02
Chapter 3
MIB Specifications
CISCO-ENTITY-FRU-CONTROL-MIB
Table 3-14
CISCO-ENTITY-EXT-MIB Object Constraints
MIB Object
Notes
ceExtConfigRegTable
Note
ceExtConfigRegNext
Read only.
ceExtSysBootImageList
Read only.
The CISCO-ENTITY-EXT-MIB is only supported for the physical entities representing active and
standby processors.
CISCO-ENTITY-FRU-CONTROL-MIB
The CISCO-ENTITY-FRU-CONTROL-MIB contains objects to configure and monitor the status of
field replaceable units (FRUs) on the Cisco 7304 router. An FRU is a hardware component (such as a
line card) that can be replaced on site.
Table 3-15 lists the constraints that the router places on objects in the
CISCO-ENTITY-FRU-CONTROL-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-15
CISCO-ENTITY-FRU-CONTROL-MIB Constraints
MIB Object
Notes
cefcModuleTable
•
•
cefcModuleAdminStatus
cefcModuleOperStatus
Supported values:
•
Enable(1)
•
Reset(3)
Note
The cefcModuleAdminStatus object cannot be set
to reset(3) for processor modules.
Note
When a line card is disabled, its
cefcModuleAdminStatus cannot be set to reset.
Supported values:
– Unknown(1)—Read-only.
– Ok(2)—Read-only.
– Failed(7)—Read-only.
•
cefcModuleResetReason
Supported values:
– Unknown(1)—Read-only.
– PowerUp(2)—Read-only.
– ManualReset(5)—Read-only.
cefcFRUPowerSupplyGroupTable
Not supported.
cefcFRUPowerStatusTable
Not supported.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-21
Chapter 3
MIB Specifications
CISCO-ENTITY-PFE-MIB
Table 3-15
CISCO-ENTITY-FRU-CONTROL-MIB Constraints (continued)
MIB Object
•
Notes
cefcMaxDefaultInLinePower
Not supported.
1 The entPhysicalEntry (which has module(9) as entPhysicalClass in the entPhysicalTable) has a corresponding entry in the
cefcModuleTable.
2 Because port adapters do not provide operational status information, they cannot be administratively controlled and
independently OIRed. Port adapters are not supported in the cefcModuleAdminStatus table.
3 The cefcPowerStatusChange notification is not supported and the cefcModuleStatusChange notification can be supported for
a redundant power supply.
CISCO-ENTITY-PFE-MIB
The CISCO-ENTITY-PFE -MIB (Packet Forwarding Engine) contains objects that maintain the
performance history on the Packet Forwarding Engine (PFE) processor listed in the ENTITY-MIB
(RFC 2737) entPhysicalTable. The PFE processor is a Cisco developed network processor technology,
which accelerates certain IP features to provide better network performance.
Table 3-16 lists the constraints that the router places on objects in the CISCO-ENTITY-PFE-MIB. For
detailed definitions of MIB objects, see the MIB.
Table 3-16
CISCO-ENTITY-PFE-MIB Constraints
MIB Object
Notes
cePfeHistRestartEvent
Not supported.
A percentage value that represents the actual utilization and efficiency performance of the PXF are
recorded in the CISCO-ENTITY-PFE-MIB. Use this MIB to access additional IP statistics. To obtain
detailed implementation information, you can issue the show hardware pxf cpu context command from
the command line interface (CLI).
Note
The PFE is the parallel express forwarding network processor (PXF), which is part of the performance
routing engine (PRE).
CISCO-ENTITY-SENSOR-MIB
The CISCO-ENTITY-SENSOR-MIB contains objects that monitor the values of sensors in the
ENTITY-MIB (RFC 2037) entPhysicalTable. The CISCO-ENTITY-SENSOR-MIB:
•
Is a Cisco private MIB to support a monitoring function of sensor devices.
•
Discovers the sensor devices in the system and provides the ability to monitor the status of the
system.
•
Provides the threshold values and notifications for each sensor.
The sensor entities shown in this MIB are the physical entities whose entity class are defined to sensor(8)
in the entPhysicalTable.
Cisco 7304 Router MIB Specifications Guide
3-22
OL-4925-02
Chapter 3
MIB Specifications
CISCO-ENTITY-VENDORTYPE-OID-MIB
CISCO-ENTITY-VENDORTYPE-OID-MIB
The CISCO-ENTITY-VENDORTYPE-OID-MIB defines the object identifiers (OIDs) assigned to
various Cisco 7304 router components. The OIDs in this MIB are used by the entPhysicalTable of the
ENTITY-MIB as values for the entPhysicalVendorType field in entPhysicalTable. Each OID uniquely
identifies a type of physical entity, such as a chassis, line cards, or port adapters.
MIB Constraints
Table 3-17 lists the objects and OIDs in the CISCO-ENTITY-VENDORTYPE-OID-MIB that describe router
entities. For detailed definitions of MIB objects, see the MIB.
Table 3-17
CISCO-ENTITY-VENDORTYPE-OID-MIB Objects and Constraints
MIB Object (OID Assignment)
Notes (Part Number)
cevChassis
•
cevChassisCisco7304
(1.3.6.1.4.1.9.12.3.1.3.304)
Cisco 7304 chassis (CISCO7304)
cevContainer
•
cevContainerSlot
(1.3.6.1.4.1.9.12.3.1.5.1)
Chassis slot
cevModule
•
cevModuleC7xxxType
(1.3.6.1.4.1.9.12.3.1.9.7)
Cisco 7300 Network Services Engine 100
•
cevCpuC7300Nse100
•
cevC7300Nse100Db
Cisco 7304 NPE-G100 Network Processing Engine
•
cevCpuC7300Npeg100
OC-3 ATM 2-port line cards
•
cevC73002Oc3AtmMm
(1.3.6.1.4.1.9.12.3.1.9.17.43)
2-port, multimode
(7300-2OC-3ATM-MM)
•
cevC73002Oc3AtmSmIr
(1.3.6.1.4.1.9.12.3.1.9.17.43)
2-port, single-mode intermediate reach
(7300-2OC-3ATM-SMI)
•
cevC73002Oc3AtmSmLr
(1.3.6.1.4.1.9.12.3.1.9.17.43)
2-port, single-mode long reach
7300-2OC-3ATM-SML)
Cisco 6-port Clear Channel T3 Card
•
cevC73006T3
OC-3/STM-1 POS/SDH, Packet over SONET/SDH line cards (2 and 4 port)
•
cevC73002Oc3PosMm
(1.3.6.1.4.1.9.12.3.1.9.17.48)
2-port, multimode
7300-2OC-3POS-MM)
•
cevC73002Oc3PosSmIr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
2-port, single-mode intermediate reach
7300-2OC-3POS-SMI)
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-23
Chapter 3
MIB Specifications
CISCO-ENTITY-VENDORTYPE-OID-MIB
Table 3-17
CISCO-ENTITY-VENDORTYPE-OID-MIB Objects and Constraints (continued)
MIB Object (OID Assignment)
Notes (Part Number)
•
cevC73002Oc3PosSmLr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
2-port, single-mode long reach
(7300-2OC-3POS-SML)
•
cevC73004Oc3PosMm
(1.3.6.1.4.1.9.12.3.1.9.17.48)
4-port, multimode
(7300-2OC-3POS-MM)
•
cevC73004Oc3PosSmIr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
4-port, single-mode intermediate reach
(7300-2OC-3POS-SMI)
•
cevC73004Oc3PosSmLr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
4-port, single-mode long reach
(7300-2OC-3POS-SML)
OC-12c/STM-16 Packet over SONET/SDH line cards (1 and 2 port)
•
cevC7300Oc12PosMm
(1.3.6.1.4.1.9.12.3.1.9.17.48)
1-port, multimode
(7300-1OC-12POS-MM)
•
cevC7300Oc12PosSmIr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
1-port, single-mode intermediate reach
(7300-1OC-12POS-SMI)
•
cevC7300Oc12PosSmLr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
1-port, single-mode long reach
(7300-1OC-12POS-SML)
•
cevC73002Oc12PosMm
(1.3.6.1.4.1.9.12.3.1.9.17.48)
2-port, multimode
(7300-2OC-12POS-MM)
•
cevC73002Oc12PosSmIr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
2-port, single-mode intermediate reach
(7300-2OC-12POS-SMI)
•
cevC73002Oc12PosSmLr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
2-port, single-mode long reach
(7300-2OC-12POS-SML)
OC-48c/STM-16 Packet over SONET/SDH line cards (1 port)
•
cevC73001Oc48PosSmSr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
1-port, single-mode short reach
(7300-1OC-48POS-SMS)
•
cevC73001Oc48PosSmIr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
1-port, single-mode intermediate reach
(7300-1OC-48POS-SMI)
•
cevC73001Oc48PosSmLr
(1.3.6.1.4.1.9.12.3.1.9.17.48)
1-port, single-mode long reach
(7300-1OC-48POS-SML)
cevPortAdapters
Cisco 7304 PCI Port Adapter Carrier cards (7300-PA-CC)
•
cevC7300CCPA
(1.3.6.1.4.1.9.12.3.1.9.7.76)
cevModuleC7300CCPA
•
cevPaAtmdxE3
(1.3.6.1.4.1.9.12.3.1.9.4.37)
1-port enhanced ATM E3 port adapter
cevPaAtmdxDs3
(1.3.6.1.4.1.9.12.3.1.9.4.38)
1-port enhanced ATM T3 port adapter
cevPa2feFx182543
(1.3.6.1.4.1.9.12.3.1.9.4.93)
2-port Fast Ethernet port adapter
cevPa2feTx182543
(1.3.6.1.4.1.9.12.3.1.9.4.92)
2-port Fast Ethernet port adapter
•
•
•
(PA-A3-E3)
(PA-A3-T3)
(PA-2FE-FX)
(PA-2FE-TX)
Cisco 7304 Router MIB Specifications Guide
3-24
OL-4925-02
Chapter 3
MIB Specifications
CISCO-ENVMON-MIB
Table 3-17
CISCO-ENTITY-VENDORTYPE-OID-MIB Objects and Constraints (continued)
MIB Object (OID Assignment)
Notes (Part Number)
cevPort
•
cevPortFEIP
(1.3.6.1.4.1.9.12.3.1.10.10)
NSE Fast Ethernet port
•
cevPortGE
(1.3.6.1.4.1.9.12.3.1.10.20)
NSE GigabitEthernet port
•
cevPortGE
(1.3.6.1.4.1.9.12.3.1.10.52)
NPE GigabitEthernet port
•
cevPortOc3
(1.3.6.1.4.1.9.12.3.1.10.80)
OC-3 ATM port
•
cevPortT3
(1.3.6.1.4.1.9.12.3.1.10.94)
Clear Channel T3 port
•
cevPortPOS
(1.3.6.1.4.1.9.12.3.1.10.96)
Packet over SONET port
•
cevPortE3Atm
(1.3.6.1.4.1.9.12.3.1.10.108)
PA-A3-E3 port
•
cevPortDs3ATM
(1.3.6.1.4.1.9.12.3.1.10.109)
PA-A3-T3 port
•
cevPortFEIP
(1.3.6.1.4.1.9.12.3.1.10.119)
PA-2FE-TX port
cevModuleSFPType
Gigabit Ethernet SFP is a 1000-Mbps optical interface with LC-type duplex connection
•
cevSFP1000BaseSx
GLC-SX-MM, short wavelength
•
cevSFP1000BaseLx
GLC-LH-SM, long wavelength, long haul
•
cevSFP1000BaseZx
GLC-ZX-SM, extended distance wavelength
cevMGBIC
Gigabit Ethernet GBIC is a 1000-Mbps optical interface with an SC-type duplex connection
•
cevMGBIC1000BaseSX
(1.3.6.1.4.1.9.12.3.1.9.16.2)
GBIC-SX or WS-G5484, short wavelength
•
cevMGBIC1000BaseSX
(1.3.6.1.4.1.9.12.3.1.9.16.2)
GBIC-LX/LH or WS-G5486, long wavelength, long haul
•
cevMGBIC1000BaseSX
(1.3.6.1.4.1.9.12.3.1.9.16.2)
GBIC-ZX or WS-G5487, extended distance wavelength
CISCO-ENVMON-MIB
The CISCO-ENVMON-MIB contains information about the status of environmental sensors (for
voltage, temperature, and power supplies). It also contains MIB objects to enable and disable
notifications for changes to the status of these sensors.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-25
Chapter 3
MIB Specifications
CISCO-FLASH-MIB
CISCO-FLASH-MIB
The CISCO-FLASH-MIB contains objects to manage flash cards and flash-card operations.
CISCO-FRAME-RELAY-MIB
The CISCO-FRAME-RELAY-MIB contains Frame Relay information that is specific to Cisco products
or that is missing from RFC 1315.
CISCO-FRAS-HOST-MIB
The CISCO-FRAS-HOST-MIB contains objects specific to upstream or host-end sessions.
CISCO-FTP-CLIENT-MIB
The CISCO-FTP-CLIENT-MIB contains objects to invoke File Transfer Protocol (FTP) operations for
network management.
CISCO-HSRP-EXT-MIB
The CISCO-HSRP-EXT-MIB provides an extension to the CISCO-HSRP-MIB. It contains objects to
perform functions such as assigning secondary HSRP IP addresses, monitoring the operational status of
interfaces, and modifying an HSRP group’s priority.
Although this MIB is included in the Cisco IOS software image, the MIB is currently not supported for
broadband configurations.
CISCO-HSRP-MIB
The CISCO-HSRP-MIB contains objects to configure and manage the Cisco Hot Standby Router
Protocol (HSRP), which is defined in RFC 2281.
CISCO-IETF-ATM2-PVCTRAP-MIB
The CISCO-IETF-ATM2-PVCTRAP-MIB supplements the ATM-MIB. It implements the virtual
channel link (VCL) section of the IETF document “draft-ietf-atommib-atm2-11.txt,” Section 9 ATM
Related Trap Support.
Cisco 7304 Router MIB Specifications Guide
3-26
OL-4925-02
Chapter 3
MIB Specifications
CISCO-IETF-IP-FORWARD-MIB
CISCO-IETF-IP-FORWARD-MIB
The CISCO-IETF-IP-FORWARD-MIB contains objects to manage multipath IP routes in a classless
interdomain routing (CIDR) environment. This MIB is based on the IETF document
draft-ietf-ipngwg-rfc2096-update-00.txt.
CISCO-IETF-IP-MIB
The CISCO-IETF-IP-MIB contains objects to manage the Internet Protocol (IP), but not to manage IP
routes. The MIB also contains objects to manage the Internet Control Message Protocol (ICMP). It is
based on the IETF document “draft-ietf-ipngwg-rfc2011-update-00.txt.”
CISCO-IMAGE-MIB
The CISCO-IMAGE-MIB is the router image MIB which identifies the identifies the characteristics and
capabilities of the Cisco IOS software image running on the router.
There are no constraints on this MIB.
CISCO-IP-STAT-MIB
The CISCO-IP-STAT-MIB contains objects to manage the collection and display of IP statistics,
categorized by IP precedence and the Media Access Control (MAC) address associated with IP packets.
To use the MIB to access additional IP statistics, you can execute the following commands from the CLI:
•
show interfaces mac-accounting
•
show interfaces precedence
CISCO-IPMROUTE-MIB
The CISCO-IPMROUTE-MIB contains objects to manage IP multicast routing on the router.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-27
Chapter 3
MIB Specifications
CISCO-ENHANCED-MEMORY-POOL-MIB
CISCO-ENHANCED-MEMORY-POOL-MIB
Note
The CISCO-ENHANCED-MEMORY-POOL-MIB is not supported in this release.
The CISCO-ENHANCED-MEMORY-POOL-MIB (Table 3-18) contains objects to monitor memory
pools on all physical entities on a managed system Memory utilization information is provided to users at
three different intervals of time: 1 minute, 5 minutes, and 10 minutes. Memory pools can be categorized into
two groups:
•
Predefined pool types—Currently predefined as:
– 1:processor memory
– 2:i/o memory
– 3:pci memory
– 4:fast memory
– 5:multibus memory
•
Dynamic pool types—Have a pool type value greater than any of the predefined types listed above.
Only the processor pool is required to be supported by all devices. Support for other pool types is
dependent on the device being managed. For detailed definitions of the
CISCO-ENHANCED-MEMORY-POOL-MIB objects, see the MIB.
Table 3-18
CISCO-ENHANCED-MEMORY-POOL-MIB Constraints
MIB Object
Notes
ciscoMemoryPoolTable
•
ciscoMemoryPoolLargestFree
•
cempMemPoolPlatformMemory
•
cempMemPoolLargestFree
•
cempMemPoolLowestFree
ciscoMemoryPoolUtilizationTable
Not supported.
Table not supported.
Note
CISCO-ENHANCED-MEMORY-POOL-MIB retrieves used and free information from sysdb namespace. If
mempool type is not found, it returns zero length to the SNMP core agent.
Note
The OLD-CISCO-MEMORY-MIB contains objects that describe memory pools on devices running an
earlier implementation of the Cisco IOS operating system. This MIB was replaced by the
CISCO-MEMORY-POOL-MIB.
Cisco 7304 Router MIB Specifications Guide
3-28
OL-4925-02
Chapter 3
MIB Specifications
CISCO-LEC-DATA-VCC-MIB
CISCO-LEC-DATA-VCC-MIB
The CISCO-LEC-DATA-VCC-MIB module is a Cisco extension to the ATM Forum's LANE Client MIB.
This extension identifies those VCCs which are being used to carry packets sent on LANE Data Direct
VCCs.
CISCO-LEC-EXT-MIB
The CISCO-LEC-EXT-MIB module is a Cisco extension to the ATM Forum's LANE client MIB.
CISCO-LECS-MIB
The CISCO-LECS-MIB contains objects that manage LANE configuration in Cisco devices.
CISCO-LES-MIB
The CISCO-LES-MIB contains objects that manage LANE service in Cisco devices.
CISCO-MEMORY-POOL-MIB
The CISCO-MEMORY-POOL-MIB contains objects to monitor memory pools on the router.
There are no constraints on this MIB.
CISCO-NETFLOW-MIB
The CISCO-NETFLOW-MIB contains objects that remotely obtains and manages cache flow
information, current NetFlow configuration, and statistics.
The Netflow MIB provides a simple and easy method to get NetFlow cache information, current NetFlow
configuration and statistics.The MIB provides Netflow information in these areas:
•
Cache information and configuration.
•
Export information and configuration.
•
Export Statistics.
•
Protocol Statistics.
•
Version 9 Export Template information.
•
Top Flows information.
To manage parameters, this MIB supports the following object groups:
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-29
Chapter 3
MIB Specifications
CISCO-NETFLOW-MIB
Table 3-19
CISCO-NETFLOW-MIB Object Groups
Objects Group
Description
cnfCacheInfo
Provides common information for all
active/inactive flows ( i.e. entries, time out etc)
per cache basis.
cnfExportInfo
Provides information about export like export
version and export destinations(/Collectors).
cnfFeatureAcceleration
Provides information about NetFlow Feature
Acceleration.
cnfExportStatistics
Provides export statistics.
cnfProtocolStatistics
Provides a summary of NetFlow cache statistics.
cnfExportTemplate
Provides Template based Version 9 flow export
information and statistic.
SNMP is used to collect network information. SNMP permits retrieval of critical information from
network elements such as routers, switches, and workstations. The CISCO-NETFLOW-MIB feature uses
SNMP to configure NetFlow and to gather NetFlow statistics.
The CISCO-NETFLOW-MIB contains objects that allow NetFlow statistics and other NetFlow data for
the managed devices on your system to be retrieved by SNMP. You can specify retrieval of NetFlow
information from a managed device (for example, a router) either by entering commands on that
managed device or by entering SNMP commands from the NMS workstation to configure the router
through the MIB.
If the NetFlow information is configured from the NMS workstation, no access to the router is required
and all configuration can be performed through SNMP. The CISCO-NETFLOW-MIB request for
information is sent from an NMS workstation through SNMP to the router and is retrieved from the
router. This information is stored or viewed, thus allowing NetFlow information to be easily accessed
and transported across a multivendor programming environment.
The CISCO-NETFLOW-MIB feature defines managed objects that enable a network administrator to
remotely monitor the following NetFlow information:
Note
•
Flow cache configuration information
•
NetFlow export information
•
General NetFlow statistics
For detailed information about the CISCO-NETFLOW-MIB, go to:
http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a00805e11
ab.html
Cisco 7304 Router MIB Specifications Guide
3-30
OL-4925-02
Chapter 3
MIB Specifications
CISCO-NDE-MIB
CISCO-NDE-MIB
The CISCO-NDE-MIB contains objects to configure and monitor the operation of the NetFlow Data
Export (NDE) feature. A network flow is a unidirectional sequence of packets between a pair of source
and destination endpoints, which are identified by IP address and transport layer application port
number. NetFlow uses the IP protocol type, type of service (ToS), and input interface identifier to
uniquely identify network flows.
CISCO-NTP-MIB
The CISCO-NTP-MIB contains objects to monitor a Network Time Protocol (NTP) server. NTP is used
to synchronize timekeeping among a set of distributed time servers and clients. Primary time servers,
which are synchronized to national time standards, are connected to widely accessible resources such as
backbone gateways. These primary servers send timekeeping information to other time servers, and
perform clock checking to eliminate timekeeping errors due to equipment or propagation failures.
CISCO-PAE-MIB
The CISCO-PAE-MIB contains objects to manage port access entities (PAEs) on the router, as defined
by IEEE Std 802.1x. The MIB contains PAE information that is not included in the IEEE8021-PAE-MIB
or that is specific to Cisco products.
CISCO-PIM-MIB
The CISCO-PIM-MIB defines Cisco specific objects and variables for managing Protocol Independent
Multicast (PIM) on the router. These MIB definitions are an extension of those in RFC 2934, which is
the IETF-PIM-MIB.
CISCO-PING-MIB
The CISCO-PING-MIB contains objects to manage ping requests on the router. There are no constraints
on this MIB.
CISCO-PROCESS-MIB
The CISCO-PROCESS-MIB displays memory and CPU usage on the router, and describes active system
processes.
CISCO-PRODUCTS-MIB
The CISCO-PRODUCTS-MIB lists the object identifiers (OIDs) assigned to Cisco hardware platforms.
The cisco7303 = 1.3.6.1.4.1.9.1.439 OID is supported.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-31
Chapter 3
MIB Specifications
CISCO-QLLC01-MIB
CISCO-QLLC01-MIB
The CISCO-QLLC01-MIB contains objects to configure and monitor logical connections for the
Qualified Logical Link Control (QLLC) protocol.
CISCO-QUEUE-MIB
The CISCO-QUEUE-MIB contains objects to manage interface queues, which can be used for FIFO,
priority, custom, and fair queuing.
CISCO-RF-MIB
The CISCO-RF-MIB contains objects related to the redundancy framework (RF), which is designed to
support the one-to-one redundancy of processor cards. Note that the MIB is not designed to support
redundant hardware, such as power supplies.
CISCO-RSRB-MIB
The CISCO-RSRB-MIB contains objects used to manage remote source-route bridging (RSRB) on the
router. This MIB provides information about the attributes of the local-remote RSRB peer relationship.
CISCO-RTTMON-MIB
The CISCO-RTTMON-MIB contains objects to monitor network performance. The MIB provides
information about the response times of network resources and applications. Each conceptual round-trip
time (RTT) control row in the MIB represents a single probe, which is used to determine an entity’s
response time. The probe defines an RTT operation to perform (for example, an FTP or HTTP get
request), and the results indicate whether the operation succeeded or failed, and the length of time it took
to complete.
If you plan to schedule an RTT operation, see Table 3-20 for information about
rttMonScheduleAdminRttStartTime in the rttMonScheduleAdminTable.
Note
An rttMonCtrlOperConnectionLostOccurred trap is generated when an RTT connection cannot be
established to the destination router because the router responder application is not running. However,
the trap is not generated if the physical connection to the router is lost.
Cisco 7304 Router MIB Specifications Guide
3-32
OL-4925-02
Chapter 3
MIB Specifications
CISCO-RTTMON-MIB
MIB Constraints
Table 3-20 lists the constraints that the Cisco 7304 router places on objects in the CISCO-RTTMON-MIB.
For detailed definitions of MIB objects, see the MIB.
Table 3-20
CISCO-RTTMON-MIB Constraints
MIB Object
Notes
RttMonProtocol
Not supported:
rttMonApplAuthTable
•
snaRUEcho
•
snaLU0EchoAppl
Not supported.
rttMonCtrlAdminTable
•
rttMonCtrlAdminRttType
Supported values:
echo(1)
pathEcho(2)
•
rttMonCtrlAdminRttType
Supported values:
udpEcho(5)
tcpConnect(6)
http(7)
dns(8)
jitter(9)
ftp(12)
All other values not supported.
rttMonEchoAdminTable
•
rttMonEchoAdminProtocol
Supported values:
ipIcmpEcho(2)
ipUdpEchoAppl(3)
ipTcpConn(24)
httpAppl(25)
dnsAppl(26)
jitterAppl(27)
ftpAppl(30)
All other values not supported.
rttMonScheduleAdminTable
•
rttMonScheduleAdminRttStartTime
rttMonHistoryCollectionTable
Before setting this object to a date/time value,
make sure the ESR clock was set through the
CLI clock set command. Otherwise, the
scheduled RTT operation does not run.
HTTP and Jitter types not supported.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-33
Chapter 3
MIB Specifications
CISCO-SDLLC-MIB
CISCO-SDLLC-MIB
The CISCO-SDLLC-MIB contains object to manage SDLC Logical Link Control (SDLLC). The MIB
contains read-only configuration and operational information for the Cisco implementation of
Synchronous Data Link Control (SDLC) to Logical Link Control, type 2 (LLC2) media translation.
CISCO-SLB-EXT-MIB
The CISCO-SLB-EXT-MIB contains extensions to the Cisco server load-balancing MIB
(CISCO-SLB-MIB). Server load balancing enables the router to balance the processing of packets and
connections from other devices, such as real servers, firewalls, or caches. An SLB device determines how
to handle incoming frames and connections according to the contents of the incoming data. Various
configuration options are available.
CISCO-SLB-MIB
The CISCO-SLB-MIB contains objects to manage server load-balancing (SLB) managers, such as those
provided by the Cisco IOS SLB product. The MIB includes objects for the manager-side implementation
of the Dynamic Feedback Protocol (DFP), which is used to obtain information about servers.
CISCO-SMI-MIB
The CISCO-SMI-MIB defines the structure of management information for Cisco enterprise MIBs.
CISCO-SNAPSHOT-MIB
The CISCO-SNAPSHOT-MIB contains objects to manage snapshot routing, which helps improve the
use of system resources for static routing and routing for dedicated serial lines.
CISCO-SONET-MIB
The CISCO-SONET-MIB contains objects to describe SONET/SDH interfaces on the router. This MIB
is an extension to the standard SONET-MIB (RFC 2558).
MIB Constraints
Currently, the Cisco 7304 router implements only the traps in this MIB. See Chapter 4, “Monitoring
Notifications.”
Cisco 7304 Router MIB Specifications Guide
3-34
OL-4925-02
Chapter 3
MIB Specifications
CISCO-STUN-MIB
CISCO-STUN-MIB
The CISCO-STUN-MIB contains objects to configure and monitor serial tunneling (STUN) on the
router. The MIB contains global STUN configuration and operational information, and objects to
manage STUN groups, ports, and routes.
CISCO-SYSLOG-MIB
The CISCO-SYSLOG-MIB contains all system log messages generated by the Cisco IOS software. The
MIB provides a way to access syslog messages through SNMP. All Cisco IOS syslog messages contain
the message name and its severity, message text, the name of the entity generating the message, and an
optional time stamp. The MIB also contains a history of syslog messages and counts related to syslog
messages.
Note
You can configure the Cisco 7304 router to send syslog messages to a ‘syslog’ server.
MIB Constraints
The MIB does not keep track of messages generated from commands entered through the command line
interface (CLI).
CISCO-TC-MIB
The CISCO-TC-MIB defines the textual conventions used in Cisco enterprise MIBs.
CISCO-TCP-MIB
The CISCO-TCP-MIB contains objects to manage the Transmission Control Protocol (TCP) on the
router. This MIB is an extension to the IETF TCP MIB.
CISCO-VINES-MIB
The CISCO-VINES-MIB provides Virtual Integrated Network Service (VINES) routing information.
The MIB also contains objects from the Cisco VINES command line interface.
CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
The CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB contains VLAN-ID and ifIndex information for
each routed virtual LAN (VLAN) interface on the router. A routed VLAN interface is the router interface
or subinterface to which you attach the IP address used by the router on the VLAN.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-35
Chapter 3
MIB Specifications
DLSW-MIB
On the Cisco 7304 router, the MIB contains information about VLAN subinterfaces created on GigE
WAN ports on the 4-port GigE WAN Optical Services Module (OSM-2+4GE-WAN+). The MIB maps
each VLAN-ID to an ifIndex, which you can use to access the ipRouteTable to obtain the routing
configuration for the routed VLAN interface.
DLSW-MIB
The DLSW-MIB (RFC 2024) contains objects to manage data-link switching (DLSw) on the router.
ENTITY-MIB
The ENTITY-MIB contains a table called, entPhysicalTable that identifies physical system components
(logical entities) in the Cisco 7304 router and allows SNMP management of those entities. This MIB is
applicable to chassis, line cards, processor cards, port adapters, fans, and power supplies.
Cisco 7304 Router MIB Specifications Guide
3-36
OL-4925-02
Chapter 3
MIB Specifications
ENTITY-MIB
The following are the five conformance groups contained in the Entity-MIB:
•
entityPhysical group—Describes the physical entities managed by a single agent.
•
entityLogical group—Describes the logical entities managed by a single agent.
•
entityMapping group—Describes the associations between the physical entities, logical entities,
interfaces, and non-interface ports managed by a single agent.
•
entityGeneral group—Describes general system attributes shared by potentially all types of entities
managed by a single agent.
•
entityNotifications group—Contains status indication notifications.
The following two groups are added from RFC 2737:
•
entityPhysical2 group—This group augments the entityPhysical group.
•
entityLogical2 group—Describes the logical entities managed by a single agent, and replaces
entityLogical group.
The MIB table entPhysicalTable identifies the physical system components in the router. The
entPhysicalTable contains 1 row for the Cisco 7304 chassis and 1 row for each entity in the chassis. A
physical entity can contain other entities. The physical hierarchy of system components is determined at
runtime, based on the actual router configuration.
MIB Constraints
Table 3-21 lists the constraints that the router places on objects in the ENTITY-MIB. For detailed definitions
of MIB objects, see the MIB.
Table 3-21
ENTITY-MIB Constraints for OSM Modules
MIB Object
Notes
entPhysicalTable
•
entPhysicalAlias
Zero length string.
•
entPhysicalAssetID
Zero length string.
entLogicalTable
•
entLogicalContextName
entLPMappingTable
Not supported.
Not supported.
The following MIB entities are dependent on each user’s configuration:
•
entPhysicalIndex—Uniquely identifies each entity in the router. The index is also used to access
information about the entity in other MIB tables.
•
entPhysicalContainedIn—Indicates the entPhysicalIndex of a component’s parent entity. The value
of entPhysicalIndex for the physical entity which 'contains' this physical entity. A value of zero
indicates this physical entity is not contained in any other physical entity.
•
entPhysicalParentRelPos—An integer that shows the relative position of same-type entities that
have the same entPhysicalContainedIn value (for example, slots and line card ports).
The entPhysicalTable contains a single row for the Cisco 7304 chassis and a row for each entity in the
chassis. A physical entity may contain other entities (for example, a fan-tray bay may contain a fan-tray
module, which may contain one or more fans). The physical hierarchy of system components is
determined at runtime, based on the actual configuration.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-37
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-22 lists entPhysicalTable entries for the Cisco 7304 router.
Table 3-22
entPhysicalTable Entries for Cisco 7304 Chassis Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
C7300 chassis
cevChassis7304
chassis
7300 Chassis
Chassis slot
cevContainerSlot
container(5)
slot 0
Contained in the
chassis
Chassis slot
cevContainerSlot
container(5)
slot 1
Contained in the
chassis.
Chassis slot
cevContainerSlot
container(5)
slot 2
Contained in the
chassis
Chassis slot
cevContainerSlot
container(5)
slot 3
Contained in the
chassis
Chassis slot
cevContainerSlot
container(5)
slot 4
Contained in the
chassis
Chassis slot
cevContainerSlot
container(5)
slot 5
Contained in the
chassis
Power supply slot
cevContainerC7304Po
werSupplyBay
container(5)
Power supply
(PS) bay 1
The device can
have 2 power
supplies in the
chassis
Power supply slot
cevContainerC7304
PowerSupplyBay
container(5)
PS bay 2
The device can
have 2 power
supplies in the
chassis
Power supply and
fan module
cevPowerSupplyC7300 Other
DC
Entity description Device supports
and PS slot
AC and DC
number
power supplies.
The power
supply and fan
are in the PS
container
Power supply and
fan module
cevPowerSupplyC7300 Other
AC
Entity description Device supports
and PS slot
AC and DC
number
power supplies.
The power
supply and fan
are in the PS
container
DC or AC power
supply
cevPowerSupply
—
Contained in the
power supply and
fan module
Power supply state cevSensorC7300PSFan sensor(8)
State
—
Contained in the
power supply
Fan
—
—
cevFan
powersupply
fan
Notes
Cisco 7304 Router MIB Specifications Guide
3-38
OL-4925-02
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-22
entPhysicalTable Entries for Cisco 7304 Chassis Components (continued)
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Fan module
cevFanC7300Fan
Module
other
Fan state
cevSensorC7300PSFan sensor(8)
State
Notes
Entity description —
and PS slot
number
—
Contained in the
fan
Table 3-23 lists entPhysicalTable entries for the Cisco 7304 router network service engine (NSE) cards.
Table 3-23
entPhysicalTable Entries for Cisco 7304 Network Service Engine Cards
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
NSE 100 CPU
card
cevCpuC7300Nse100
module(9)
Entity description
and slot number
7300 NSE
occupies 2
slots. It is
contained in
either slots 0
and 1 or slots 2
and 3.
module(9)
Entity description
and slot number
Contained in
NSE-100 only.
7304-NPE-G100
cevCpuC7300Npeg100 module(9)
Entity description
and slot number
7300 network
route processor
engine is
contained in
either slots 0
and 1 or slots 2
and 3.
Mistral EOBC
cevPortFEIP
port(10)
FastEthernet0
Only contained
in the primary
NSE-100.
Pinnacle GE
cevPortGE
port(10)
GigabitEthernet0/0
GigabitEthernet0/1
GigabitEthernet2/0
GigabitEthernet2/1
Contained in
the primary and
standby
NSE-100. There
are 2 GE ports
per NSE-100.
BCM1250
Internal MAC
cevPortGE
port(10)
GigabitEthernet0
or
GigabitEthernet1
or
GigabitEthernet2
Only contained
in the primary
NPE-G100.
NSE DB
temperature
sensor
cevSensorC7300NseDb sensor(8)
TempVoltage
Entity description
and slot number
Contained in
the primary
NSE DB.
NSE 100 daughter cevC7300Nse100Db
card
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-39
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-23
entPhysicalTable Entries for Cisco 7304 Network Service Engine Cards (continued)
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
NSE DB 1.65 V
sensor
cevSensorC7300NseDb sensor(8)
TempVoltage
Entity description
and slot number
Contained in
the primary
NSE DB.
NSE DB 1.8 V
sensor
cevSensorC7300NseDb sensor(8)
TempVoltage
Entity description
and slot number
Contained in
the primary
NSE DB.
Table 3-24 lists entPhysicalTable entries for the Cisco 7304 Router OC-3 ATM components.
Table 3-24
entPhysicalTable Entries for Cisco 7304 OC-3 ATM Card Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
2-port ATM OC-3
multimode
cevC73002Oc3AtmMm
module(9)
Entity description 2-port OC-3
and slot number
ATM line card
2-port ATM OC-3
SM Intermediate
Range
cevC73002Oc3AtmSmIr
module(9)
Entity description 2-port OC-3
and slot number
ATM line card
2-port ATM OC-3
SM Long Range
cevC73002Oc3AtmSmLr module(9)
Entity description 2-port OC-3
and slot number
ATM line card
4-port ATM OC-3
multimode
cevC73004Oc3AtmMm
module(9)
Entity description 4-port OC-3
and slot number
ATM line card
4-port ATM OC-3
SM Intermediate
Range
cevC73004Oc3AtmSmIr
module(9)
Entity description 4-port OC-3
and slot number
ATM line card
4-port ATM OC-3
SM Long Range
cevC73002Oc3AtmSmLr module(9)
Entity description 4-port OC-3
and slot number
ATM line card
atm_oc3
Temperature
Sensor
cevSensorModuleDevice
Temp
sensor(8)
Entity description Contained in
and slot number
OC-3 ATM
line card
atm_oc3 1.8 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
OC-3 ATM
line card
atm_oc3 2.5 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
OC-3 ATM
line card
atm_oc3 3.3 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
OC-3 ATM
line card
atm_oc3 12 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
OC-3 ATM
line card
OC-3 ATM
cevPortOC3
port(10)
ATM and slot
number and port
number.
Contained in
OC-3 ATM
line card
Cisco 7304 Router MIB Specifications Guide
3-40
OL-4925-02
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-25 lists entPhysicalTable entries for the Cisco 7304 Router OC-3-POS components.
Table 3-25
entPhysicalTable Entries for Cisco 7304 OC-3-POS Line Card Components
entPhysicalDescr entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
2-port POS OC-3 cevC73002Oc3PosMm
multimode
module(9)
Entity description 2-port
and slot number
OC-3c/STM-1
POS line card
2-port POS OC-3 cevC73002Oc3PosSmIr
SM Intermediate
Range
module(9)
Entity description 2-port
and slot number
OC-3c/STM-1
POS line card
2-port POS OC-3 cevC73002Oc3PosSmLr
SM Long Range
module(9)
Entity description 2-port
and slot number
OC-3c/STM-1
POS line card
4-port POS OC-3 cevC73004Oc3PosMm
multimode
module(9)
Entity description 4-port
and slot number
OC-3c/STM-1
POS line card
4-port POS OC-3 cevC73004Oc3PosSmIr
SM Intermediate
Range
module(9)
Entity description 4-port
and slot number
OC-3c/STM-1
POS line car
4-port POS OC-3 cevC73004Oc3PosSmLr
SM Long Range
module(9)
Entity description 4-port
and slot number
OC-3c/STM-1
POS line car
pos_oc3
Temperature
Sensor
cevSensorModuleDevice
Temp
sensor(8)
Entity description Contained in
and slot number
the OC-3 POS
line card
pos_oc3 1.5 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
the OC-3 POS
line card
pos_oc3 1.8 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
the OC-3 POS
line card
pos_oc3 2.5 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
the OC-3 POS
line card
pos_oc3 3.3 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
the OC-3 POS
line card
pos_oc3 12 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
the OC-3 POS
line card
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-41
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-26 lists entPhysicalTable entries for the Cisco 7304 router OC-12-POS components.
Table 3-26
entPhysicalTable Entries for Cisco 7304 OC-12-POS Card Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
1-port POS OC-12 cevC7300Oc12PosMm
Multimode
module(9)
Entity description 1-port
and slot number. OC-12c/STM4 POS line card
1-port POS OC-12 cevC7300Oc12PosSmIr
SM Intermediate
Range
module(9)
Entity description 1-port
and slot number. OC-12c/STM4 POS line card
1-port POS OC-12 cevC7300Oc12PosSmLr
SM Long Range
module(9)
Entity description 1-port
and slot number. OC-12c/STM4 POS line card
2-port POS OC-12 cevC73002Oc12PosMm
Multimode
module(9)
Entity description 2-port
and slot number. OC-12c/STM4 POS line card
2-port POS OC-12 cevC73002Oc12PosSmIr
SM Intermediate
Range
module(9)
Entity description 2-port
and slot number. OC-12c/STM4 POS line card
2-port POS OC-12 cevC73002Oc12PosSmLr module(9)
SM Long Range
Entity description 2-port
and slot number. OC-12c/STM4 POS line card
pos_oc12
Temperature
Sensor
cevSensorModuleDevice
Temp
sensor(8)
Entity description Contained in
and slot number. OC-12 POS
line card
pos_oc12 1.5 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number. OC-12 POS
line card
pos_oc12 1.8 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number. OC-12 POS
line card
pos_oc12 2.5 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number. OC-12 POS
line card
pos_oc12 3.3 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number. OC-12 POS
line card
pos_oc12 12 V
Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description Contained in
and slot number
OC-12 POS
line card
Cisco 7304 Router MIB Specifications Guide
3-42
OL-4925-02
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-27 lists entPhysicalTable entries for the Cisco 7304 router OC-48-POS components.
Table 3-27
entPhysicalTable Entries for Cisco 7304 OC-48-POS Card Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
1-port POS OC-48 cevC7300Oc48PosSmSr
SM Short Range
module(9)
Entity description 1-port
and slot number
OC-48c/STM-1
6 POS line card
Port POS OC-48
SM Intermediate
Range
cevC7300Oc48PosSmIr
module(9)
Entity description 1-port
and slot number
OC-48c/STM-1
6 POS line card
1-port POS OC-48 cevC7300Oc48PosSmL
SM Long Range
module(9)
Entity description 1-port
and slot number
OC-48c/STM-1
6 POS line card
Packet over
SONET
cevPortPOS
port(10)
POS and slot
number and port
number
pos_oc48
Temperature
Sensor
cevSensorModuleDevice sensor(8)
Temp
Entity description Contained in
and slot number
OC-48 POS line
cards
pos_oc48 1.5 V
Sensor
cevSensorModuleDevice sensor(8)
Voltage
Entity description Contained in
and slot number
OC-48 POS line
cards
pos_oc48 1.8 V
Sensor
cevSensorModuleDevice sensor(8)
Voltage
Entity description Contained in
and slot number
OC-48 POS line
cards
pos_oc48 2.5 V
Sensor
cevSensorModuleDevice sensor(8)
Voltage
Entity description Contained in
and slot number
OC-48 POS line
cards
pos_oc48 3.3 V
Sensor
cevSensorModuleDevice sensor(8)
Voltage
Entity description Contained in
and slot number
OC-48 POS line
cards
pos_oc48 12 V
Sensor
cevSensorModuleDevice sensor(8)
Voltage
Entity description Contained in
and slot number
OC-48 POS line
cards
Contained in all
POS line cards
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-43
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-28 lists entPhysicalTable entries for the Cisco 7304 Router modules, ports, and temperature
sensors.
Table 3-28
entPhysicalTable Entries for Cisco 7304 Router Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
6-port T3
cevC73006T3
module(9)
Entity description 6-port Clear
and slot number
Channel T3
line card
FastEthernet
Interface
cevPortFEIP
module(9)
Fast Ethernet and
slot and port
number
Packet over DS3
cevPortDs3
module(9)
Serial and slot and Contained in
port number
6-port T3
ds3 Temperature
Sensor
cevSensorModuleDevice
Temp
sensor(8)
Entity description —
and slot number
ds3 1.8 V Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description —
and slot number
ds3 2.5 V Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description —
and slot number
ds3 3.3 V Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description —
and slot number
ds3 12 V Sensor
cevSensorModuleDevice
Voltage
sensor(8)
Entity description —
and slot number
—
Table 3-29 lists entPhysicalTable entries for the Cisco 7304 router inlet and outlet temperature sensor
components and port adapter sensor components.
Table 3-29
entPhysicalTable Entries for Cisco 7304 Router Temperature Sensor Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
Outlet
Temperature
Sensor
cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Inlet Temperature
Sensor
cevSensorC7300Inlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Hotspot
Temperature
Sensor
cevSensorC7300Hotspot sensor(8)
TempVoltage
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Cisco 7304 Router MIB Specifications Guide
3-44
OL-4925-02
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-29
entPhysicalTable Entries for Cisco 7304 Router Temperature Sensor Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
Outlet 1.8 V
Sensor
cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Outlet 2.5 V
Sensor
cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Outlet 3.3 V
Sensor
cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Outlet 5 V Sensor cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Outlet 12 V
Sensor
cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Inlet 1.8 V Sensor cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Inlet 3.3 V Sensor cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Inlet 1.5 V Sensor cevSensorC7300Outlet
TempVoltage
sensor(8)
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-45
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-29
entPhysicalTable Entries for Cisco 7304 Router Temperature Sensor Components
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Hotspot 1.8 V
Sensor
cevSensorC7300Outlet
TempVoltage
sensor(8)
Notes
Entity description Contained in
and slot number
Primary
NSE-100 or
primary
NPE-G100*
* Be aware that the entPhysicalTable entries for the NSE-100 and NPE-G100 temperature/voltage sensors vary for each
hardware version of the NSE-100 and NPE-G100 cards. Table 3-30 provides you with the temperature/voltage entries for
the specific hardware versions (Revision 4 and Revision 5) of these cards.
Table 3-30 lists entPhysicalTable entries for the Cisco 7304 NSE-100 and NPE-G100 line card
temperature and voltage entries for hardware Revision 4 and Revision 5.
Note
Be aware that you may observe various MIB object values if you are running different versions of
hardware.
Table 3-30
entPhysicalTable Temperature and Voltage Entries for Cisco 7304 NSE-100 and
NPE-G100 Line Cards
NSE-100 Line Card
Hardware Revision 4.0
NSE-100CR Line Card
Hardware Revision 4.0
NSE-100CR Line Card
Hardware Revision 5.0
NPE-G100 Line Card
Hardware Revision 5.0
volttab_t
volt_table_nse100
volttab_t
volt_table_nse100cr
volttab_t
volt_table_nse100cr
volttab_t
volt_table_npeg100
nse outlet 1.8 V
nse outlet 1.8 V
nse outlet 1.8 V
npe outlet 2.5 V
nse outlet 2.5 V
nse outlet 2.5 V
nse outlet 2.5 V
npe outlet 3.3 V
nse outlet 3.3 V
nse outlet 3.3 V
nse outlet 3.3 V
npe outlet 5.0 V
nse outlet 5 V
nse outlet 5 V
nse outlet 5 V
npe outlet 12.0 V
nse outlet 12 V
nse outlet 12 V
nse outlet 12 V
npe outlet 3.3c V
nse inlet 1.8 V
nse inlet 1.8 V
nse inlet 1.8 V
npe inlet 1.5 V
nse inlet 3.3 V
nse inlet 3.3 V
nse inlet 3.3 V
npe outlet 1.8 V
nse hotspot 1.8 V
nse inlet 1.5 V
nse inlet 1.5 V
npe outlet 1.2 V
nse db 1.65 V
nse hotspot 1.8 V
nse hotspot 1.8 V
npe outlet 1.2c V
nse db 1.65 V
nse db 1.60 V
nse db 1.65 V
—
nse db 1.8 V
nse db 1.8 V
nse db 1.8 V
—
Cisco 7304 Router MIB Specifications Guide
3-46
OL-4925-02
Chapter 3
MIB Specifications
ENTITY-MIB
Table 3-31 lists entPhysicalTable entries for the Cisco 7304 router port adapter cards.
Table 3-31
entPhysicalTable Entries for Cisco 7304 PCI Port Adapter Carrier Card—7300-CC-PA
entPhysicalDescr
entPhysicalVendorType
entPhysicalClass entPhysicalName
Notes
Port Adapter
Carrier Card
cevC7300CCPA
module(9)
Entity description Globe Master
and slot number
Jacket Card
PA-2FE-TX
cevPa2feTx
module(9)
Entity description Contained in
and slot number
CC-PA-BAY
and bay number
ENHANCED
ATM E3 Port
Adapter
cevPaAtmdxE3
module(9)
Entity description Contained in
and slot number
CC-PA-BAY
and bay number
ENHANCED
ATM PA
cevPortE3Atm
port(10)
ATM and slot and Uses the PA-CC
port number
slot number
Port Adapter Slot
cevModuleC7300CCPA module
Entity description Can contain
and slot number
PAs supported
in C7304
pacc hotspot
Temperature
Sensor
cevSensorTemperature
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc coolspot
Temperature
Sensor
cevSensorTemperature
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc -12 V Sensor cevSensorVoltage
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc 1.2 V Sensor cevSensorVoltage
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc 1.5 V Sensor cevSensorVoltage
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc 2.5 V Sensor cevSensorVoltage
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc 3.3 V Sensor cevSensorVoltage
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc 5.15 V
Sensor
cevSensorVoltage
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
pacc 12 V Sensor
cevSensorVoltage
sensor(8)
Entity description Contained in
and slot number
the PA carrier
cards
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-47
Chapter 3
MIB Specifications
ETHERLIKE-MIB
ETHERLIKE-MIB
The ETHERLIKE-MIB (RFC 2665) contains objects to manage Ethernet-like interfaces on the
Cisco 7304 router.
MIB Constraints
Table 3-32 lists the constraints that the Cisco 7304 router places on objects in the ETHERLIKE-MIB. Any
objects not listed in this table are implemented as defined in the MIB. For detailed definitions of MIB objects,
see the MIB.
Table 3-32
ETHERLIKE-MIB Constraints
MIB Table/Object
Notes
dot3CollTable
Not implemented
dot3ControlTable
Not implemented
dot3PauseTable
Not implemented
Table 3-33 shows usage of ifTable for Ethernet-like layer.
Table 3-33
ETHERLIKE-MIB ifTable Usage
MIB ifTable Object
Use for GigaEthernet Layer
IfDescr
GE-WAN<slot>/<port>
IfType
EthernetCsmacd(6)
IfSpeed
1000000000
IfPhysAddress
MAC Address
IfName
GE<slot>/<port>
IfLinkUpDownTrapEnable
enabled(1)
IfHighSpeed
1000
ifConnectorPresent
true(1)
EVENT-MIB
The EVENT-MIB contains objects to define event triggers and actions for network management
purposes.
EXPRESSION-MIB
The EXPRESSION-MIB contains objects to define expressions of MIB objects for network management
purposes.
Cisco 7304 Router MIB Specifications Guide
3-48
OL-4925-02
Chapter 3
MIB Specifications
HC-RMON-MIB
HC-RMON-MIB
The MIB module for managing remote monitoring device implementations. This MIB module augments
the original RMON MIB as specified in RFC 1757 and RFC 1513 and RMON2 MIB as specified in
RFC 2021.
IEEE8021-PAE-MIB
The Port Access Entity module for managing IEEE 802.1X.
IEEE8023-LAG-MIB
The IEEE 8023-LAG-MIB is the Link Aggregation module for managing IEEE Standard 802.3ad.
IF-MIB
The IF-MIB (RFC 2233) describes the attributes of physical and logical interfaces. The router supports
the ifGeneralGroup of MIB objects for all layers (ifIndex, ifDescr, ifType, ifSpeed, ifPhysAddress,
ifAdminStatus, ifOperStatus, ifLastChange, ifName, ifLinkUpDownTrapEnable, ifHighSpeed, and
ifConnectorPresent).
MIB Constraints
Table 3-34 lists the constraints that the Cisco 7304 router places on objects in the IF-MIB. For detailed
definitions of MIB objects, see the MIB.
Table 3-34
IF-MIB Constraints
MIB Object
Notes
ifXTable
•
IfPromiscuousMode
Read-only.
ifStackTable
•
IfStackStatus
For creating and removing table entries, the only
supported values are createAndGo(4) and destroy(6).
ifRcvAddressTable
•
IfRcvAddressStatus
For creating and removing table entries, the only
supported values are createAndGo(4) and destroy(6).
•
IfRcvAddressType
The only supported value is other(1).
OSM ifTable Values
This section contains tables that list the ifTable values used for OSMs in the Cisco 7304 router.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-49
Chapter 3
MIB Specifications
IF-MIB
Table 3-35
ifTable Object Values and Constraints for OC-12 ATM OSM Cards
OSM-2-OC-12-ATM
SONET Layer
ATM and ATM Subinterface Layer
AAL5 and AAL5 Subinterface Layer
IfDescr
ATM slot/port
ATM slot/port–ATM layer
ATM slot/port.subif–ATM subif layer
ATM slot/port–AAL5 layer
ATM slot/port.subif–AAL5 subif layer
IfType
sonet(39)
atm(37)
atmSubInterface(134)
aal5(49)
IfMtu
4470
Not used.
Not used.
IfSpeed
599040000
599040000
0
IfPhysAddress
Zero length string.
Zero length string.
Zero length string.
ifAdminStatus
Not used.
Read-only. (ATM layer)
Not used. (ATM subinterface)
Read-only. (AAL5 layer)
Not used. (AAL5 subinterface)
ifInUnknownProtos
Not used.
Not used.
0
ifInMulticastPkts
Not used.
Not used.
0
ifInBroadcastPkts
Not used.
Not used.
0
ifOutMulticastPkts
Not used.
Not used.
0
ifOutBroadcastPkts
Not used.
Not used.
0
IfName
AT slot/port
AT slot/port
AT slot/port
IfHighSpeed
599
599
0
IfPromiscuousMode
false(2)
false(2)
false(2)
IfConnectorPresent
true(1)
false(2)
false(2)
IfAlias
Not used.
Read-only. (ATM layer)
Not used. (ATM subinterface)
Read-only. (AAL5 layer)
Not used. (AAL5 subinterface)
ifTable
Table 3-36
ifTable Object Values for GigE WAN OSMs
OSM-2+4GE-WAN+
Gigabit Ethernet Layer
VLAN 802.1Q Subinterface Layer
IfDescr
GE–WAN slot/port
GE–WAN slot/port.subif–802.1Q vLAN subif
IfType
EthernetCsmacd(6)
l2vlan(135)
IfSpeed
1000000000
1000000000
IfPhysAddress
MAC address
MAC address
IfName
GE slot/port
Gi slot/port.subif
IfLinkUpDownTrapEnable
enabled(1)
enabled(1)
IfHighSpeed
1000
1000
IfConnectorPresent
true(1)
false(2)
ifTable
Cisco 7304 Router MIB Specifications Guide
3-50
OL-4925-02
Chapter 3
MIB Specifications
IGMP-MIB
Table 3-37
ifTable Object Values for DS3 Channelized T1/E1 OSMs
OSM-12CT3-T1
DS3 Layer
DS1 Layer
IfDescr
T3 slot/subslot/port
E3 slot/subslot/port
T1 slot/subslot/port
E1 slot/subslot/port
IfType
ds3(30)
ds1(18)
IfSpeed
44736000 (DS3)
34368000 (E3)
1544000 (DS1)
2048000 (E1)
IfPhysAddress
The circuit ID value, or zero length The circuit ID value, or zero length
string.
string.
IfName
T3 slot/subslot/port
E3 slot/subslot/port
T1 slot/subslot/port
E1 slot/subslot/port
IfLinkUpDownTrapEnable
enabled(1)
enabled(1)
IfHighSpeed
45 (DS3)
34 (E3)
2
IfConnectorPresent
true(1)
true(1)
ifTable
Table 3-38
RFC1407-MIB Constraints
MIB Object
Notes
dsx3ConfigTable
•
dsx3LineType
Supported values is E3 supports e3other(6) and
e3Plcp(8)
•
dsx3LineCoding
Read-only.
T3 supports dsx3B3ZS(2) value only.
E3 supports e3HDB3(3) value only.
•
dsx3SendCode
Read-only. Supports dsx3SendNoCode value only.
•
dsx3CircuitIdentifier
Read-only.
•
dsx3LoopbackConfig
Read-only.
dsx3FarEndConfigTable
Not supported.
dsx3FarEndCurrentTable
Not supported.
dsx3FarEndIntervalTable
Not supported.
dsx3FarEndTotalTable
Not supported.
1 All T3/ATM line cards only support RO on all variables. See IF-MIB section for use of ifTable.
2 The RFC1407-MIB use supports the following port adapter line card types: PA-MC-T3, PA-MC-E3,
PA-A3-T3, PA-A3-E3.
IGMP-MIB
The IGMP-MIB contains objects to manage the Internet Group Management Protocol (IGMP) on the
router.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-51
Chapter 3
MIB Specifications
INT-SERV-GUARANTEED-MIB
INT-SERV-GUARANTEED-MIB
The INT-SERV-GUARANTEED-MIB describes the guaranteed service of the Integrated Services
Protocol (ISP).
INT-SERV-MIB
The INT-SERV-MIB describes the Integrated Services Protocol (ISP).
IPMROUTE-MIB
The IPMROUTE-MIB contains objects to manage IP multicast routing on the router, independent of the
actual multicast routing protocol in use.
LAN-EMULATION-CLIENT-MIB
This module defines a portion of the management information base (MIB) for managing ATM LAN
Emulation Client nodes. It is meant to be used in connection with the AToM MIB and MIB-II / RFC 1573
'ifTable' entries for each LEC / emulated 802.x network interface. The RFC1406-MIB provides access
to configuration and performance monitoring information for DS1 controllers and interfaces on the
Cisco 7304 router.
MPLS-LDP-MIB
The MPLS-LDP-MIB (version 1) provides management information for the Multiprotocol Label
Switching (MPLS) Label Distribution Protocol (LDP), which is used by label switching routers (LSRs)
to communicate the definitions of labels that each router is using. The router supports the IETF draft
version of this MIB (draft-ietf-mpls-ldp-mib-08.txt).
For detailed information about this MIB, see its feature module description at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120limit/120st/120st21/ld
pmib21.htm
Cisco 7304 Router MIB Specifications Guide
3-52
OL-4925-02
Chapter 3
MIB Specifications
MPLS-LDP-MIB
MIB Constraints
Table 3-39 lists the constraints that the Cisco 7304 router places on objects in the MPLS-LDP-MIB. For
detailed definitions of MIB objects, see the MIB. Any object not listed in this table is implemented as
defined in the MIB.
Table 3-39
MPLS-LDP-MIB Constraints
MIB Object
Notes
mplsLdpEntityTable
•
mplsLdpEntityProtocolVersion
Read-only.
•
mplsLdpEntityAdminStatus
Read-only.
•
mplsLdpEntityWellKnownDiscoveryPort
Read-only. Always 646
•
mplsLdpEntityMaxPduLength
Read-only.
•
mplsLdpEntityKeepAliveHoldTimer
Read-only.
•
mplsLdpEntityHelloHoldTimer
Read-only.
•
mplsLdpEntityFailedInitSessionTrapEnable
Read-only.
•
mplsLdpEntityFailedInitSessionThreshold
Read-only.
•
mplsLdpEntityLabelDistributionMethod
Read-only. Value
downstreamUnsolicited(2))
•
mplsLdpEntityPVLimitMismatchTrapEnable
Read-only.
•
mplsLdpEntityPathVectorLimit
Read-only.
•
mplsLdpEntityHopCountLoopDetection
Read-only.
•
mplsLdpEntityHopCount
Read-only.
•
mplsLdpEntityTargetedPeer
Read-only.
•
mplsLdpEntityTargetedPeerAddrType
Read-only.
•
mplsLdpEntityTargetedPeerAddr
Read-only.
•
mplsLdpEntityOptionalParameters
Read-only.
•
mplsLdpEntityDiscontinuityTime
Read-only.
•
mplsLdpEntityStorageType
Read-only. (Value volatile(2))
•
mplsLdpEntityRowStatus
Read-only. (Value active(1))
mplsLdpEntityConfGenericTable
•
mplsLdpConfGenericIfIndexOrZero
Read-only.
•
mplsLdpConfGenericLabel
Read-only.
•
mplsLdpConfGenericStorageType
Read-only.
•
mplsLdpConfGenericRowStatus
Read-only.
mplsLdpEntityAtmParmsTable
•
mplsLdpEntityAtmIfIndexOrZero
Read-only.
•
mplsLdpEntityAtmMergeCap
Read-only. Value vcMerge(2)
•
mplsLdpEntityAtmLabelRangeComponents
Read-only. Value is 0
•
mplsLdpEntityAtmVcDirectionality
Read-only. Value unidirectional(1)
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-53
Chapter 3
MIB Specifications
MPLS-LDP-MIB
Table 3-39
MPLS-LDP-MIB Constraints (continued)
MIB Object
Notes
•
mplsLdpEntityAtmLsrConnectivity
Read-only.
•
mplsLdpEntityDefaultControlVpi
Read-only.
•
mplsLdpEntityDefaultControlVci
Read-only.
•
mplsLdpEntityUnlabTrafVpi
Read-only.
•
mplsLdpEntityUnlabTrafVci
Read-only.
•
mplsLdpEntityAtmStorageType
Read-only. Value volatile(2)
•
mplsLdpEntityAtmRowStatus
Read-only. Value iactive(1)
mplsLdpEntityConfAtmLabelRangeTable
•
mplsLdpEntityConfAtmLabelRange-MaximumVpi Read-only.
•
mplsLdpEntityConfAtmLabelRange-MaximumVci Read-only.
•
mplsLdpEntityConfAtmLabelRange-StorageType Read-only.
•
mplsLdpEntityConfAtmLabelRange-RowStatus
Read-only.
mplsLdpEntityFrameRelayParmsTable
•
mplsLdpEntityFrIfIndexOrZero
Read-only.
•
mplsLdpEntityFrMergeCap
Read-only.
•
mplsLdpEntityFrLabelRangeComponents
Read-only.
•
mplsLdpEntityFrLen
Read-only.
•
mplsLdpEntityFrVcDirectionality
Read-only.
•
mplsLdpEntityFrParmsStorageType
Read-only.
•
mplsLdpEntityFrParmsRowStatus
Read-only.
mplsLdpEntityConfFrLabelRangeTable
•
mplsLdpConfFrMaximumDlci
Read-only.
•
mplsLdpConfFrStorageType
Read-only.
•
mplsLdpConfFrRowStatus
Read-only.
mplsLdpAtmSessionTable
Not supported.
mplsLdpFrameRelaySessionTable
Not supported.
mplsLdpSessionPeerAddressTable
Not supported.
mplsLdpLibTable
Not supported.
mplsLdpFecTable
Not supported.
mplsLdpEntityConfGenericTable
Not supported.
mplsLdpEntityConfAtmLabelRangeTable
Not supported.
mplsLdpEntityFrameRelayParmsTable
Not supported.
mplsLdpEntityConfFrLabelRangeTable
•
mplsLdpLibLspUp
Not supported.
•
mplsLdpLibLspDown
Not supported.
Cisco 7304 Router MIB Specifications Guide
3-54
OL-4925-02
Chapter 3
MIB Specifications
MPLS-LSR-MIB
MPLS-LSR-MIB
The MPLS-LSR-MIB provides configuration and performance monitoring information to manage label
switched paths (LSPs) through a label switching router (LSR) that is using the Multiprotocol Label
Switching (MPLS) technology. The router supports the IETF version of the MPLS-LSR-MIB.
For detailed information about this MIB, see its feature module description at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/relnote/7000fam/rn120st.htm
#31417
MIB Constraints
Table 3-40 lists the constraints that the Cisco 7304 router places on objects in the MPLS-LSR-MIB. For
detailed definitions of MIB objects, see the MIB. Any object not listed in the table is implemented as
defined in the MIB.
Table 3-40
MPLS-LSR-MIB Constraints
MIB Object
Notes
mplsInterfaceConfTable
•
mplsInterfaceConfStorageType
Default read-only(5).
•
mplsInterfaceAvailableBandwidth
Read-only. Always 0.
•
mplsInterfaceTotalBandwidth
Read-only. Always 0.
•
mplsInterfaceTotalBuffer
Read-only. Always 0.
•
MplsInterfaceAvailableBuffer
Read-only. Always 0.
mplsInterfacePerfTable
•
mplsInterfaceInPackets
Read-only. Always 0.
•
mplsInterfaceInDiscards
Read-only. Always 0.
•
mplsInterfaceFailedLabelLookup
Read-only. Always 0.
•
mplsInterfaceOutPackets
Read-only. Always 0.
•
mplsInterfaceOutDiscards
Read-only. Always 0.
•
mplsInterfaceOutFragments
Read-only. Always 0.
mplsInSegmentTable
•
mplsInSegmentAdminStatus
Read-only. Always up(1).
•
mplsInSegmentOperStatus
Always up(1).
•
mplsInSegmentNPop
Read-only.
•
mplsInSegmentAddrFamily
Read-only.
•
mplsInSegmentOwner
Read-only. Other(1)
•
mplsInSegmentTrafficParamPtr
Read-only. Always 0.
•
mplsInSegmentRowStatus
Read-only. Active(5).
•
mplsInSegmentStorageType
Read-only. Volatile(2)
mplsInSegmentPerfTable
•
mplsInSegmentOctets
Read-only. Always 0.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-55
Chapter 3
MIB Specifications
MPLS-LSR-MIB
Table 3-40
MPLS-LSR-MIB Constraints (continued)
MIB Object
Notes
•
mplsInSegmentPackets
Read-only. Always 0.
•
mplsInSegmentHCOctets
Read-only. Always 0.
•
mplsInSegmentErrors
Read-only. Always 0.
•
mplsInSegmentDiscards
Read-only. Always 0.
•
mplsInSegmentPerforDiscontinuityTime
Read-only. Always 0.
mplsOutSegmentTable
•
mplsOutSegmentIfIndex
Read-only.
•
mplsOutSegmentPushTopLabel
Read-only.
•
mplsOutSegmentTopLabel
Read-only.
•
mplsOutSegmentNextHopIpAddrType
Read-only.
•
mplsOutSegmentNextHopIpv4Addr
Read-only.
•
mplsOutSegmentNextHopIpv6Addr
Always 0.
•
mplsOutSegmentOwner
Read-only. Other(1).
•
mplsOutSegmentTrafficParamPtr
Always 0.
•
mplsOutSegmentRowStatus
Read-only. Active(5).
•
mplsOutSegmentStorageType
Read-only. Volatile(2).
•
mplsOutSegmentAdminStatus
Read-only. Always up(1).
•
mplsOutSegmentOperStatus
Always up(1).
mplsOutSegmentPerfTable
•
mplsOutSegmentOctets
Read-only. Always 0.
•
mplsOutSegmentPackets
Read-only. Always 0.
•
mplsOutSegmentHCOctets
Read-only. Always 0.
•
mplsOutSegmentErrors
Read-only. Always 0.
•
mplsOutSegmentDiscards
Read-only. Always 0.
•
mplsOutSegmentPerfDiscontinuityTime
Read-only. Always 0.
mplsXCTable
•
mplsXCLspId
Read-only. Does not support tunnel IDs.
•
mplsXCLabelStackIndex
Read-only. Value is set to 0 because
XCLabelStack is unsupported.
•
mplsXCIsPersistent
Read-only.
•
mplsXCOwner
Read-only. Other(1).
•
mplsXCRowStatus
Read-only.
•
mplsXCStorageType
Read-only.
•
mplsXCAdminStatus
Read-only. Always up(1).
•
mplsXCOperStatus
Always up(1).
•
mplsOutSegmentIndexNext
Read-only.
Cisco 7304 Router MIB Specifications Guide
3-56
OL-4925-02
Chapter 3
MIB Specifications
MPLS-TE-MIB
Table 3-40
MPLS-LSR-MIB Constraints (continued)
MIB Object
Notes
•
mplsXCIndexNext,
Read-only.
•
mplsLabelStackIndexNext
Read-only.
•
mplsTrafficParamIndexNext
Read-only.
mplsLabelStackTable
Not supported.
mplsTrafficParamTable
•
mplsInSegmentTrapEnable
Read-only.
•
mplsOutSegmentTrapEnable
Read-only.
•
mplsXCTrapEnable
Read-only.
•
mplsXCUp
*Not supported.
•
mplsXCDown
*Not supported.
•
mplsInSegmentUp
*Not supported.
•
mplsInSegmentDown
*Not supported.
•
mplsOutSegmentUp
*Not supported.
•
mplsOutSegmentDown
*Not supported.
* Not implemented due to scalability issues.
* mplsInterfaceConfTable—Provides information for each MPLS-capable interface on an LSR.
* mplsInterfacePerfTable—Augments the MPLS interface configuration table.
* mplsInSegmentTable—Contains a description of incoming segments at an LSR and their associated parameters.
Administrative and operational status objects for this table control packet transmission. If administrative and operational
status objects are down, the LSR does not forward packets. If these status objects are up, the LSR forwards packets.
* mplsInSegmentPerfTable—Augments the MPLS in-segment table, providing performance information and counters for
incoming segments on an LSR.
* mplsOutSegmentTable—Contains a description of outgoing segments from an LSR and their associated parameters.
Administrative and operational status objects for this table control packet transmission. If administrative and operational
status objects are down, the LSR does not forward packets. If these values are up, the LSR forwards packets.
* mplsOutSegmentPerfTable—Augments the MPLS out-segment table, providing performance information and counters for
outgoing segments on an LSR.
* mplsXCTable—Associates inSegments (labels) to outSegments (labels) to show the manager how the LSR is currently
swapping these labels. A row in this table consists of one cross-connect entry that is indexed by the cross-connect index, the
interface index of the incoming segment, the incoming label, and the out-segment index. The administrative and operational
objects for this table control packet forwarding to and from a cross-connect entry (XCEntry). The administrative status and
operational status are always up in the Cisco implementation. Otherwise, the LSR would not forward packets.
MPLS-TE-MIB
The MPLS-TE-MIB enables the Cisco 7304 router to perform traffic engineering for MPLS tunnels. The
MIB is based on Revision 05 of the IETF MPLS-TE-MIB.
Traffic engineering support for MPLS tunnels requires the following configuration:
•
Setting up MPLS tunnels along with appropriate configuration parameters.
•
Configuring tunnel loose and strict source routed hops.
Refer to the Cisco MPLS MIB team web page for more documentation on this MIB:
http://mpls-mib-group.cisco.com/
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-57
Chapter 3
MIB Specifications
MPLS-TE-MIB
MIB Constraints
Table 3-41 lists the constraints that the Cisco 7304 router places on objects in the MPLS-TE-MIB. For
detailed definitions of MIB objects, see the MIB. Any objects not listed in this table are implemented as
defined in the MIB.
Table 3-41
MPLS-TE-MIB Constraints
MIB Object
Notes
mplsTunnelIndexNext
Always 0.
mplsTunnelTable
•
mplsTunnelName
Read-only.
•
mplsTunnelDescr
Read-only.
•
mplsTunnelIsIf
Read-only.
•
mplsTunnelXCPointer
Read-only.
•
mplsTunnelSignallingProto
Read-only.
•
mplsTunnelSetupPrio
Read-only.
•
mplsTunnelHoldingPrio
Read-only.
•
mplsTunnelSessionAttributes
Read-only.
•
mplsTunnelOwner
Read-only.
•
mplsTunnelLocalProtectInUse
Read-only. Always false(2).
•
mplsTunnelResourcePointer
Read-only.
•
mplsTunnelInstancePriority
Read-only. Always 0.
•
mplsTunnelHopTableIndex
Read-only.
•
mplsTunnelIncludeAnyAffinity
Read-only. Always 0.
•
mplsTunnelIncludeAllAffinity
Read-only.
•
mplsTunnelExcludeAllAffinity
Read-only.
•
mplsTunnelPathInUse
Read-only.
•
mplsTunnelRole
Read-only.
•
mplsTunnelTotalUpTime
Read-only.
•
mplsTunnelInstanceUpTime
Read-only. Always 0.
•
mplsTunnelAdminStatus
Read-only.
•
mplsTunnelRowStatus
Read-only. Always active(1).
•
mplsTunnelStorageType
Read-only. Volatile(2). Always active.
No constraints on other table objects.
mplsTunnelHopListIndexNext
Read-only. Always 0.
mplsTunnelHopTable
•
mplsTunnelHopAddrType
Read-only.
•
mplsTunnelHopIpv4Addr
Read-only.
•
mplsTunnelHopIpv4PrefixLen
Read-only.
•
mplsTunnelHopIpv6Addr
Read-only.
Cisco 7304 Router MIB Specifications Guide
3-58
OL-4925-02
Chapter 3
MIB Specifications
MPLS-VPN-MIB
Table 3-41
MPLS-TE-MIB Constraints (continued)
MIB Object
Notes
•
mplsTunnelHopIpv6PrefixLen
Read-only.
•
mplsTunnelHopAsNumber
Read-only.
•
mplsTunnelHopLspId
Read-only.
•
mplsTunnelHopType
Read-only.
•
mplsTunnelHopRowStatus
Read-only. Always active(1).
•
mplsTunnelHopStorageType
Read-only. Volatile(2). Always active.
mplsTunnelResourceIndexNext
Read-only. Always 0.
mplsTunnelResourceTable
•
mplsTunnelResourceMaxRate
Read-only.
•
mplsTunnelResourceMeanRate
Read-only.
•
mplsTunnelResourceMaxBurstSize
Read-only.
•
mplsTunnelResourceRowStatus
Read-only. Always active(1).
•
mplsTunnelResourceStorageType
Read-only. Volatile(2). Always active.
MPLS-VPN-MIB
The MPLS-VPN-MIB:
•
Describes managed objects for modeling a Multi-Protocol Label Switching/Border Gateway
Protocol Virtual Private network.
•
Configures and monitor routes and route targets for each VRF instance on a router
•
Facilitates provisioning VPN Routing and Forwarding (VRF) instances on MPLS interfaces
•
Measures the performance of MPLS/BGP VPNs
The MIB is based on Revision 05 of the IETF MPLS-VPN-MIB.
Note
Refer to the Cisco MPLS MIB team web page for more documentation on this MIB:
http://mpls-mib-group.cisco.com/.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-59
Chapter 3
MIB Specifications
MPLS-VPN-MIB
MIB Constraints
Table 3-42 lists the constraints that the Cisco 7304 router places on objects in the MPLS-VPN-MIB. For
detailed definitions of MIB objects, see the MIB. Any objects not listed in the table are implemented as
defined in the MIB.
Table 3-42
MPLS-VPN-MIB Constraints
MIB Object
Notes
MplsNumVrfSecViolationThreshExceeded
Not supported.
mplsVpnVrfSecTable
•
MplsVpnVrfSecIllegalLabelViolations
Read-only. Always 0.
•
MplsVpnVrfSecIllegalLabelRcvThresh
Read-only. Always 0.
mplsVpnVrfTable
•
MplsVpnVrfConfRowStatus
Read-only.
•
MplsVpnVrfConfStorageType
Read-only. Volatile(2).
•
MplsVpnVrfConfMidRouteThreshold
Read-only.
•
MplsVpnVrfConfHighRouteThreshold
Read-only
•
MplsVpnVrfConfMaxRoutes
Read-only
•
MplsVpnVrfConfMaxPossibleRoutes
Read-only. Always 0.
•
MplsVpnVrfDescription
Read-only
•
MplsVpnInterfaceVpnClassification
Read-only
mplsVpnInterfaceConfTable
•
MplsVpnInterfaceConfStorageType
Read-only. Volatile(2).
•
MplsVpnInterfaceConfRowStatus
Read-only.
Values: active(1), notInService(2).
•
MplsVpnInterfaceLabelEdgeType
Read-only. providerEdge(1).
mplsVpnVrfRouteTargetTable
•
MplsVpnVrfRouteTargetRowStatus
Read-only. Values: active(1), notInService(2).
mplsVpnVrfBgpNbrAddrTable
•
MplsVpnVrfBgpNbrRowStatus
Read-only. Values: active(1), notInService(2).
•
MplsVpnVrfBgpNbrRole
Read-only. providerEdge(1).
•
MplsVpnVrfBgpNbrType
Read-only.
•
MplsVpnVrfBgpNbrAddr
Read-only.
•
MplsVpnVrfBgpNbrStorageType
Read-only. Volatile(2).
mplsVpnVrfRouteTable
•
MplsVpnVrfRouteInfo
Read-only. Value zero length string OID.
•
MplsVpnVrfRouteTarget
Read-only. Determines the route distinguisher for
this target.
Cisco 7304 Router MIB Specifications Guide
3-60
OL-4925-02
Chapter 3
MIB Specifications
MSDP-MIB
Table 3-42
MPLS-VPN-MIB Constraints (continued)
MIB Object
Notes
•
MplsVpnVrfRouteTargetDescr
Description of the route target. This object is not
supported in this Cisco IOS release. Therefore, the
object is the same as mplsVpnVrfRouteTarget.
•
MplsVpnVrfRouteDistinguisher
Read-only.
•
MplsVpnVrfRouteNextHopAS
Read-only. Value always 0.
•
MplsVpnVrfRouteRowStatus
Read-only. This object normally reads active(1),
but may read notInService(2), if a VRF was
recently deleted.
•
MplsVpnVrfRouteStorageType
Read-only. Volatile(2).
•
MplsVpnVrfRouteDestAddrType
Read-only.
•
MplsVpnVrfRouteMaskAddrType
Read-only.
•
MplsVpnVrfRouteTos
Read-only. Value always 0.
•
MplsVpnVrfRouteNextHop
Read-only.
•
MplsVpnVrfRouteNextHopAddrType
Read-only.
•
MplsVpnVrfRouteIfIndex
Read-only.
•
MplsVpnVrfRouteType
Read-only.
•
MplsVpnVrfRouteProto
Read-only.
mplsVpnVrfBgpNbrPrefixTable
Not supported.
The mplsVpnVrfConfTable represents all the MPLS/BGP VPNs configured. The NMS configures an entry in this table for each
MPLS/BGP VPN configured to run in this MPLS domain. The mplsVPNInterfaceConfTable extends the interface MIB to
provide specific MPLS/BGP VPN information on MPLS/BGP VPN-enabled interfaces. The mplsVPNPerfTable enhances
the mplsVpnVrfConfTable to provide performance information.
The mplsVpnVrfRouteTable and the mplsVpnRouteTargetTable facilitate the configuration and monitoring of routes and route
targets, respectively, for each VRF instance.
MSDP-MIB
The MSDP-MIB contains objects to monitor the Multicast Source Discovery Protocol (MSDP). The
MIB can be used with SNMPv3 to remotely monitor MSDP speakers.
For more information about this MIB, see its feature module description at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t5/dt5msdp.htm
NOTIFICATION-LOG-MIB
The NOTIFICATION-LOG-MIB defines objects that record notification information against lost
notifications, whether those are traps or informs (the two types of notifications supported). This MIB
provides common infrastructure for other MIBs in the form of a local logging function.
The management stations:
•
Query the MIB using GET requests to determine if they missed any notifications which were
generated but were never received.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-61
Chapter 3
MIB Specifications
NOVELL-IPX-MIB
•
Refine the MIB logs by using the SNMP SET operation on objects which enable control over log
sizes. This control can be executed on a global basis (affecting the whole Notification Log MIB
database) or on a per named log basis.
•
Specify the maximum time a notification can remain logged in the Notification Log MIB.
Note
Because this MIB logs all notifications, this ensures that all notifications which are dropped
from the trap queue are also logged by this MIB. Inform retries are not logged. Traps sent to
multiple recipients are logged only one time. Currently, this MIB logs notifications originating
at the local engine only.
Table 3-43 describes the constraints on objects from the NOTIFICATION-LOG-MIB. Any objects not
listed in this table are defined as in the MIB.
Table 3-43
Note
NOTIFICATION-LOG-MIB Object Constraints
MIB Object
Notes
nlmConfigGlobalEntryLimit
Value is Unsigned32. Read only.
nlmConfigGlobalAgeOut
Value is Unsigned32. Read only.
nlmConfigLogTable
Read only.
Apart from the constraints listed in Table 3-43, only the default log is supported in this release. Besides
the named logs, each system has a default log with a name as a zero length string. This log has no security
checking associated with it.
NOVELL-IPX-MIB
The NOVELL-IPX-MIB defines the management information for a system using the IPX protocol. This
MIB is designed to provide a basic framework for the management of systems implementing the IPX
protocol. This MIB is virtually identical to the IPX MIB distributed as a part of the Novell NetWare Link
Services Protocol (NLSP) Specification 1.0, Novell Part Number 100-001708-002, 2nd Edition Feb '94.
NOVELL-NLSP-MIB
The NOVELL-NLSP-MIB defines the management information for the NLSP protocol running in an
IPX environment. It provides information in addition to that contained in the IPX MIB. This MIB is
virtually identical to the NLSP MIB distributed as a part of the Novell NetWare Link Services Protocol
(NLSP) Specification 1.0, Novell Part Number 100-001708-002, 2nd Edition Feb '94.
Cisco 7304 Router MIB Specifications Guide
3-62
OL-4925-02
Chapter 3
MIB Specifications
NOVELL-RIPSAP-MIB
NOVELL-RIPSAP-MIB
The NOVELL-RIPSAP-MIB defines the management information for the RIP and SAP protocols
running in an IPX environment. It provides information in addition to that contained in the IPX MIB
itself. This MIB is virtually identical to the RIPSAP MIB distributed as a part of the Novell NetWare
Link Services Protocol (NLSP) Specification 1.0, Novell Part Number 100-001708-002, 2nd Edition
Feb '94.
OLD-CISCO-APPLETALK-MIB
The OLD-CISCO-APPLETALK-MIB provides information about Appletalk traffic on the router.
OLD-CISCO-CHASSIS-MIB
The OLD-CISCO-CHASSIS-MIB describes chassis objects in devices running an earlier release of the
Cisco IOS operating system. This MIB is deprecated, and is being replaced by the ENTITY-MIB.
However, the Cisco 7304 router implements the OLD-CISCO-CHASSIS-MIB to support earlier network
management applications that do not implement the ENTITY-MIB.
Network management applications that do not support the ENTITY-MIB can use the
OLD-CISCO-CHASSIS-MIB to discover port adapters.
MIB Constraints
The OLD-CISCO-CHASSIS-MIB is deprecated. Most chassis objects are now described in the
ENTITY-MIB; therefore, where possible, we recommend that you use the ENTITY-MIB instead of the
OLD-CISCO-CHASSIS-MIB.
The OLD-CISCO-CHASSIS-MIB is supported on the Cisco 7304 router for modules and port adapters.
Table 3-44 lists the constraints that the router places on objects in the MIB. For detailed definitions of
MIB objects, see the MIB.
Table 3-44
OLD-CISCO-CHASSIS-MIB Constraints for Line Cards and Port Adapters
MIB Object
Notes
cardTable
•
cardType
The following values are used for 7304 router cards:
Module or Port Adapter cardType Value
PA-A3-T3—pa-atmdx-ds3(406)
PA-A3-E3—pa-atmdx-e3(407)
PA-2FE-FX—cevPa2feFxI82543
PA-2FE-TX— cevPa2feTxI82543
7300-PA-CC—c7300-cc-pa(2138)
•
cardOperStatus
cardIfIndexTable
Port adapter status matches module status.
Used for port adapters only.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-63
Chapter 3
MIB Specifications
OLD-CISCO-CPU-MIB
OLD-CISCO-CPU-MIB
The OLD-CISCO-CPU-MIB describes CPU usage and active system processes on devices running an
earlier implementation of the Cisco IOS operating system.
OLD-CISCO-DECNET-MIB
The OLD-CISCO-DECNET-MIB provides information about the implementation of DECnet on the
router. DECnet is group of communications products (including a protocol suite) developed by Digital
Equipment Corporation that supports the Open System Interconnection (OSI) protocol and proprietary
Digital protocols.
OLD-CISCO-INTERFACES-MIB
The OLD-CISCO-INTERFACES-MIB contains objects to manage interfaces on devices running an
earlier implementation of the Cisco IOS operating system.
OLD-CISCO-IP-MIB
The OLD-CISCO-IP-MIB contains objects to manage IP on devices running an earlier implementation
of the Cisco IOS operating system.
OLD-CISCO-MEMORY-MIB
The OLD-CISCO-MEMORY-MIB contains objects that describe memory pools on devices running an
earlier implementation of the Cisco IOS operating system.
OLD-CISCO-NOVELL-MIB
The OLD-CISCO-NOVELL-MIB provides information about Novell traffic on the router, including
packet counts and IPX accounting and checkpoint accounting information.
OLD-CISCO-SYSTEM-MIB
The OLD-CISCO-SYSTEM-MIB provides information about the router (such as its name, software
bootload, and configuration file), and contains controls for reloading software onto the router and
clearing the Address Resolution Protocol (ARP) cache.
Cisco 7304 Router MIB Specifications Guide
3-64
OL-4925-02
Chapter 3
MIB Specifications
OLD-CISCO-TCP-MIB
OLD-CISCO-TCP-MIB
Starting with Cisco IOS software Release 10.2, all objects defined in this MIB have been deprecated.
They have been replaced with the objects defined in the CISCO-TCP-MIB.my document. Management
applications should no longer examine the objects defined in this MIB.
OLD-CISCO-TS-MIB
The OLD-CISCO-TS-MIB provides information about the number of terminal lines and virtual lines on
this device.
OLD-CISCO-VINES-MIB
The OLD-CISCO-VINES-MIB group is present in all router-based products. It provides the total input
and output number of vines.
OLD-CISCO-XNS-MIB
The OLD-CISCO-XNS-MIB provides the total number of packets.
PIM-MIB
The PIM-MIB contains objects to configure and manage Protocol Independent Multicast (PIM) on the
router. The MIB is extracted from RFC 2934.
Table 3-45 describes the constraints on tables from the PIM-MIB. Any objects or tables not listed in this
table are defined as in the MIB.
Table 3-45
PIM-MIB Object or Table Constraints
MIB Object
Notes
pimInterfaceTable
Read-only.
pimComponentTable
Read-only.
pimCandidateRPTable
Read-only.
RFC1213-MIB
The RFC1213-MIB defines the second version of the Management Information Base (MIB-II) for use
with network-management protocols in TCP-based internets.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-65
Chapter 3
MIB Specifications
RFC1243-MIB
RFC1243-MIB
The RFC1243-MIB uses the extended OBJECT-TYPE macro as defined in llapEntry 9 (9). The total
number of times this LocalTalk interface received a lapRTS packet and expected a data packet, but did
not receive any data packet.
RFC1253-MIB
The RFC1253-MIB contains objects to manage Version 2 of the Open Shortest Path First (OSPF)
protocol.
RFC1315-MIB
The RFC1315-MIB contains objects to manage a Frame Relay data terminal equipment (DTE) interface,
which consists of a single physical connection to the network with many virtual connections to other
destinations and neighbors. The MIB contains the objects used to manage:
•
The Data Link Connection Management Interface (DLCMI)
•
Virtual circuits on each Frame Relay interface
•
Errors detected on Frame Relay interfaces
RFC1381-MIB
The RFC1381-MIB (LAPB MIB file) was extracted from RFC 1381. The LAPB administration table
contains objects that can manage a LAPB interface.
RFC1382-MIB
The RFC1382-MIB was extracted from RFC 1382. Several changes were made to the MIB to allow it to
compile in a Cisco environment:
•
Remove IMPORT statements for EntryStatus, PositiveInteger, and IfIndexType.
•
Hand-imported the above types by copying the definitions from their respective files.
•
The range of x25OperRestartCount was increased to be the largest integer possible.
RFC1406-MIB (DS1)
The RFC1406-MIB provides access to configuration and performance monitoring information for
DS1 controllers and interfaces on the Cisco 7304 router.
Cisco 7304 Router MIB Specifications Guide
3-66
OL-4925-02
Chapter 3
MIB Specifications
RFC1407-MIB (DS3)
RFC1407-MIB (DS3)
The RFC1407-MIB (DS3-MIB) provides access to configuration and performance monitoring
information for DS1 controllers and interfaces.
MIB Constraints
Table 3-38 on page 3-51 lists the constraints that the Cisco 7304 router places on objects in the
RFC1407-MIB. For detailed definitions of MIB objects, see the MIB. Any other object not listed in the table
is implemented as defined in the RFC1407-MIB.
RFC2006-MIB
The RFC2006-MIB is the MIB module for the Mobile IP.
RMON-MIB
The RMON-MIB contains objects to remotely monitor devices in the network. Supports MIB version
RFC 1757.
RMON2-MIB
The RMON2-MIB contains objects to manage remote monitoring device implementations. This MIB
module augments the original RMON MIB as specified in RFC 1757. We support the RFC 2021 version
of the MIB.
RS-232-MIB
The RS232-MIB contains objects to manage RS-232-like hardware interfaces and devices.
RSVP-MIB
The RSVP-MIB contains objects to manage the Resource Reservation Protocol (RSVP).
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-67
Chapter 3
MIB Specifications
SMON-MIB
SMON-MIB
The SMON-MIB manages remote monitoring device implementations for Switched Networks. Identifies
the source of the data that the associated function is configured to analyze. This Textual Convention
extends the DataSource Textual Convention defined by RMON 2 to the following data source types:
•
ifIndex
•
smonVlanDataSource
•
entPhysicalEntry
SNA-SDLC-MIB
The SNA-SDLC-MIB contains objects that manage SDLC (synchronous data link control) devices.
SNMP-FRAMEWORK-MIB
The SNMP-FRAMEWORK-MIB (RFC 2571) contains objects that describe the SNMP management
architecture.
There are no constraints on this MIB.
SNMP-NOTIFICATION-MIB
The SNMP-NOTIFICATION-MIB contains managed objects for SNMP v3 notifications. The MIB also
defines a set of filters that limit the number of notifications generated by a particular entity
(snmpNotifyFilterProfileTable and snmpNotifyFilterTable).
Objects in the snmpNotifyTable are used to select entities in the SNMP-TARGET-MIB
snmpTargetAddrTable and specify the types of SNMP notifications those entities are to receive.
SNMP-PROXY-MIB
The SNMP-PROXY-MIB contains managed objects to remotely configure the parameters used by an
SNMP entity for proxy forwarding operations. The MIB contains a single table, snmpProxyTable, which
defines the translations to use to forward messages between management targets.
Cisco 7304 Router MIB Specifications Guide
3-68
OL-4925-02
Chapter 3
MIB Specifications
SNMP-TARGET-MIB
SNMP-TARGET-MIB
The SNMP-TARGET-MIB (RFC 2573) contains objects to remotely configure the parameters used by
an entity to generate SNMP notifications. The MIB defines the addresses of entities to send SNMP
notifications to, and contains a list of tag values that are used to filter the notifications sent to these
entities (see the SNMP-NOTIFICATION-MIB). There are no constraints on this MIB.
SNMP-USM-MIB
The SNMP-USM-MIB (RFC 2574) contains objects that describe the SNMP User-based Security
Model. There are no constraints on this MIB.
SNMP-VACM-MIB
The SNMP-VACM-MIB (RFC 2575) contains objects that describe the view-based access control model
for SNMP.
Note
To access this MIB, you must create an SNMP v3 user with access to a view that includes all of the
information from the Internet subtree. For example:
Router(config)# snmp-server view abcview internet included
Router(config)# snmp-server group abcgroup v3 noauth read abcview write abcview
notify abcview
Router(config)# snmp-server user abcuser abcgroup v3
SNMPv2-MIB
The SNMPv2-MIB contains objects SNMPv2 entities. The SNMPv2-MIB contains the following
mandatory object groups:
•
SNMP group—Collection of objects providing basic instrumentation and control of an
SNMP entity.
•
System group—Collection of objects common to all managed systems.
•
snmpSetGroup—Collection of objects which allow several cooperating SNMPv2 entities, all acting
in a manager role, to coordinate their use of the SNMPv2 set operation.
•
snmpBasicNotificationsGroup—The two notifications are coldStart and authenticationFailure
which an SNMPv2 entity is required to implement.
SONET-MIB
The SONET-MIB (RFC 1595) contains objects to manage both configuration and performance managing
objects for SONET interfaces.
Cisco 7304 Router MIB Specifications Guide
OL-4925-02
3-69
Chapter 3
MIB Specifications
SOURCE-ROUTING-MIB
MIB Constraints
Table 3-46 lists the constraints that the Cisco 7304 router places on objects in the SONET-MIB. Any
other objects not listed in the table are defined as in the RFC1595-MIB definition. For detailed
definitions of MIB objects, see the MIB.
Table 3-46
SONET-MIB Constraints
MIB Object
Notes
sonetPathCurrentTable
•
sonetPathCurrentWidth
Read-only.
sonetVTCurrentTable
Not supported.
sonetVTIntervalTable
Not supported.
sonetFarEndVTCurrentTable
Not supported.
sonetFarENdVTIntervalTable
Not supported.
SOURCE-ROUTING-MIB
The SOURCE-ROUTING-MIB contains objects to configure and manage source routing and source
routing transparent bridges. We support the RFC 1525 version of the MIB.
TCP-MIB
The TCP-MIB (RFC 2012) contains objects to manage the Transmission Control Protocol (TCP)
implementations on the router. There are no constraints.
UDP-MIB
The UDP-MIB (RFC 2013) contains objects to manage the User Datagram Protocol (UDP) on the router.
There are no constraints.
Cisco 7304 Router MIB Specifications Guide
3-70
OL-4925-02
Download PDF

advertising