Cisco Systems 7600 MIB Network Router User Manual

CH A P T E R
3
Cisco 7600 MIB Specifications
This chapter describes the Management Information Base (MIB) on the Cisco 7600 Series router. It
includes the following sections:
•
Cisco 7600 MIBs, page 3-1
•
CISCO 7600 MIB Categories, page 3-1
– Supported and Verified MIBs, page 3-1
– Supported and Unverified MIBs, page 3-2
– Unverified or Unsupported MIBs, page 3-2
•
MIB Version String Description, page 3-2
Cisco 7600 MIBs
Each MIB description lists relevant constraints about the MIB’s implementation on the Cisco 7600
router platform. Any objects not listed in a table are implemented as defined in the MIB. For detailed
MIB descriptions, see the standard MIB.
Note
Not all MIBs included in a Cisco IOS software release are fully supported by the router. Some MIBs are
not supported at all. Other MIBs might work, but they have not been tested on the router. In addition,
some MIBs are deprecated but cannot be removed from the software. When a MIB is included in the
image, this does not necessarily mean it is supported by the Cisco 7600 platform.
To determine which MIBs are included in other releases, see the “Using Cisco IOS MIB Tools” section
on page 2-1.
CISCO 7600 MIB Categories
The MIBs in the c7600 Image on the Cisco 7600 Series router are categorized into three types:
Supported and Verified MIBs
The MIB exists in the image, the code is implemented, and Cisco has verified that all the supported
objects work properly. These MIBs are tested for Cisco 7600 router.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-1
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Supported and Unverified MIBs
The MIB exists in the image, the code is implemented, but we have not verified if it is working properly.
In other words, the user may get something if they query the MIB. However, the information may be
correct or incorrect because the MIB has not been tested. These MIBs are not tested for Cisco 7600
router support.
Unverified or Unsupported MIBs
The MIB exists in the image but is either not tested or not supported. These MIBs are neither tested nor
supported for Cisco 7600 routers.
MIB Version String Description
The MIB version string indicates the date and time that the module was most recently modified. The
format is YYMMDDHHMMZ or YYYYMMDDHHMMZ where
•
YY - last 2 digits of the year (only years between 1900-1999)
•
YYYY - all 4 digits of the year (any year)
•
MM - month (01 through 12)
•
DD - day of the month (01 through 31)
•
HH - hours (00 through 23)
•
MM - minutes (00 through 59)
•
Z - denotes UTC/GMT (the ASCII character Z) Coordinated Universal Time (UTC, formerly
Greenwich Mean Time). This datatype stores the datetime fields YEAR, MONTH, DAY, HOUR,
MINUTE, SECOND, TIMEZONE_HOUR, and TIMEZONE_MINUTE.
Note
Note
For example, 9592192015Z and 199509122015Z represent 8:15 GMT on 19 February 1995.
Years after 1999 use the four digit format. Years 1900-1999 may use the 2 or 4 digit format.
In the following table you might see the term Revision not available. This term refers to the MIB module
that does not have a recorded time stamp indicating the latest modification.
MIBs in 7600 Series Routers
Table 3-1 lists the MIBs in 7600 Series Routers:
Table 3-1
MIBs in 7600 Series Routers
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
ATM-MIB
•
12.2(18)SXF3
9406072245
•
12.2(33)SRA
9406072245
Cisco 7600 Series Router MIB Specifications Guide
3-2
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRB
9406072245
•
12.2(33)SRC
9406072245
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
BGP4-MIB
•
12.2(18)SXF3
9405050000Z
•
12.2(33)SRA
9405050000Z
•
12.2(33)SRB
9405050000Z
•
12.2(33)SRC
9405050000Z
BRIDGE-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
CISCO-802-TAP-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200403110000Z
•
12.2(33)SRC
200403110000Z
CISCO-AAA-SESSION-MIB
•
12.2(18)SXF3
9911160000Z
•
12.2(33)SRA
9911160000Z
•
12.2(33)SRB
9911160000Z
•
12.2(33)SRC
200603210000Z
CISCO-AAL5-MIB
•
12.2(18)SXF3
200309220000Z
•
12.2(33)SRA
200309220000Z
•
12.2(33)SRB
200309220000Z
•
12.2(33)SRC
200309220000Z
CISCO-ACCESS-ENVMON-MIB
•
12.2(18)SXF3
9808050000Z
•
12.2(33)SRA
9808050000Z
•
12.2(33)SRB
9808050000Z
•
12.2(33)SRC
9808050000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-3
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-ALPS-MIB
•
12.2(18)SXF3
200001280000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-ASPP-MIB
•
12.2(18)SXF3
9508210000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-ATM-EXT-MIB
•
12.2(18)SXF3
9706200000Z
•
12.2(33)SRA
200301060000
•
12.2(33)SRB
200301060000
•
12.2(33)SRC
200301060000
CISCO-ATM-PVC-MIB
•
12.2(18)SXF3
9711180000Z
•
12.2(33)SRA
9711180000Z
•
12.2(33)SRB
9711180000Z
•
12.2(33)SRC
9711180000Z
CISCO-ATM-PVCTRAP-EXTN-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200303240000Z
CISCO-ATM-QOS-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200206100000Z
CISCO-BCP-MIB
•
12.2(18)SXF3
200408310000Z
•
12.2(33)SRA
200408310000Z
•
12.2(33)SRB
200408310000Z
•
12.2(33)SRC
200408310000Z
Cisco 7600 Series Router MIB Specifications Guide
3-4
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-BGP-POLICY-ACCOUNTING-MIB
•
12.2(18)SXF3
9912170000Z
•
12.2(33)SRA
200207260000Z
•
12.2(33)SRB
200207260000Z
•
12.2(33)SRC
200207260000Z
CISCO-BGP4-MIB
•
12.2(18)SXF3
200108130000Z
•
12.2(33)SRA
200302240000Z
•
12.2(33)SRB
200302240000Z
•
12.2(33)SRC
200302240000Z
CISCO-BRIDGE-EXT-MIB
•
12.2(18)SXF3
200408230000Z
•
12.2(33)SRA
200408230000Z
•
12.2(33)SRB
200408230000Z
•
12.2(33)SRC
200408230000Z
CISCO-BSC-MIB
•
12.2(18)SXF3
9701250000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-BSTUN-MIB
•
12.2(18)SXF3
9701220000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-BULK-FILE-MIB
•
12.2(18)SXF3
9810291700Z
•
12.2(33)SRA
9810291700Z
•
12.2(33)SRB
9810291700Z
•
12.2(33)SRC
200108220000Z
CISCO-CABLE-DIAG-MIB
•
12.2(18)SXF3
200409130000Z
•
12.2(33)SRA
200409130000Z
•
12.2(33)SRB
200409130000Z
•
12.2(33)SRC
200409130000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-5
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-CALLHOME-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200704060000Z
CISCO-CAR-MIB
•
12.2(18)SXF3
0002180000Z
•
12.2(33)SRA
0002180000Z
•
12.2(33)SRB
0002180000Z
•
12.2(33)SRC
0002180000Z
CISCO-CASA-FA-MIB
•
12.2(18)SXF3
200209180000Z
•
12.2(33)SRA
200209180000Z
•
12.2(33)SRB
200209180000Z
•
12.2(33)SRC
200209180000Z
CISCO-CASA-MIB
•
12.2(18)SXF3
200209180000Z
•
12.2(33)SRA
200209180000Z
•
12.2(33)SRB
200209180000Z
•
12.2(33)SRC
200209180000Z
CISCO-CAT6K-CROSSBAR-MIB
•
12.2(18)SXF3
200411190000Z
•
12.2(33)SRA
200411190000Z
•
12.2(33)SRB
200411190000Z
•
12.2(33)SRC
200411190000Z
CISCO-CDP-MIB
•
12.2(18)SXF3
9812100000Z
•
12.2(33)SRA
200503210000Z
•
12.2(33)SRB
200503210000Z
•
12.2(33)SRC
200503210000Z
CISCO-CEF-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200601300000Z
Cisco 7600 Series Router MIB Specifications Guide
3-6
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-CIRCUIT-INTERFACE-MIB
•
12.2(18)SXF3
200005090000Z
•
12.2(33)SRA
200005090000Z
•
12.2(33)SRB
200005090000Z
•
12.2(33)SRC
200005090000Z
CISCO-CLASS-BASED-QOSMIB
•
12.2(18)SXF3
200012080000Z
•
12.2(33)SRA
200404120000Z
•
12.2(33)SRB
200404120000Z
•
12.2(33)SRC
200404120000Z
CISCO-CONFIG-COPY-MIB
•
12.2(18)SXF3
9701150000Z
•
12.2(33)SRA
200403170000Z
•
12.2(33)SRB
200403170000Z
•
12.2(33)SRC
200608220000Z
CISCO-CONFIG-MAN-MIB
•
12.2(18)SXF3
9511280000Z
•
12.2(33)SRA
9511280000Z
•
12.2(33)SRB
200406180000Z
•
12.2(33)SRC
200608220000Z
CISCO-CONTEXT-MAPPING-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200503170000Z
•
12.2(33)SRC
200503170000Z
CISCO-CSG-MIB
•
12.2(18)SXF3
200302200000Z
•
12.2(33)SRA
200302200000Z
•
12.2(33)SRB
200302200000Z
•
12.2(33)SRC
200302200000Z
CISCO-DATA-COLLECTION-MIB
•
12.2(18)SXF3
•
12.2(33)SRA
Y
200210300530Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-7
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRB
200210300530Z
•
12.2(33)SRC
200210300530Z
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-DIAL-CONTROL-MIB
•
12.2(18)SXF3
9801161546Z
•
12.2(33)SRA
9801161546Z
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-DLCSW-MIB
•
12.2(18)SXF3
9702190000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-DLSW-EXT-MIB
•
12.2(18)SXF3
9703110000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-DLSW-MIB
•
12.2(18)SXF3
9506300900Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-DSPU-MIB
•
12.2(18)SXF3
9508150000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-EIGRP-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-EMBEDDED-EVENT-MGR-MIB
•
12.2(18)SXF3
200304160000Z
•
12.2(33)SRA
200304160000Z
Cisco 7600 Series Router MIB Specifications Guide
3-8
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
•
12.2(33)SRB
200304160000Z
•
12.2(33)SRC
200304160000Z
Not in
Image
CISCO-ENHANCED-IMAGE-M
IB
•
12.2(18)SXF3
200501060000Z
•
12.2(33)SRA
200501060000Z
•
12.2(33)SRB
200501060000Z
•
12.2(33)SRC
200501060000Z
CISCO-ENHANCED-MEMORY-POOL-MIB
•
12.2(18)SXF3
200106050000Z
•
12.2(33)SRA
200302240000Z
•
12.2(33)SRB
200302240000Z
•
12.2(33)SRC
200302240000Z
CISCO-ENTITY-ALARM-MIB
•
12.2(18)SXF3
9907062150Z
•
12.2(33)SRA
9907062150Z
•
12.2(33)SRB
9907062150Z
•
12.2(33)SRC
9907062150Z
CISCO-ENTITY-ASSET-MIB
•
12.2(18)SXF3
200207231600Z
•
12.2(33)SRA
200207231600Z
•
12.2(33)SRB
200207231600Z
•
12.2(33)SRC
200207231600Z
CISCO-ENTITY-EXT-MIB
•
12.2(18)SXF3
200104050000Z
•
12.2(33)SRA
200104050000Z
•
12.2(33)SRB
200104050000Z
•
12.2(33)SRC
200104050000Z
CISCO-ENTITY-FRU-CONTROL-MIB
•
12.2(18)SXF3
200310230000Z
•
12.2(33)SRA
200310230000Z
•
12.2(33)SRB
200310230000Z
•
12.2(33)SRC
200310230000Z
CISCO-ENTITY-SENSOR-MIB
•
12.2(18)SXF3
200301070000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-9
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRA
200509080000Z
•
12.2(33)SRB
200601010000Z
•
12.2(33)SRC
200601010000Z
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-ENTITY-VENDORTYPE-OID-MIB
•
12.2(18)SXF3
200204051400Z
•
12.2(33)SRA
200204051400Z
•
12.2(33)SRB
200204051400Z
•
12.2(33)SRC
200505050930Z
CISCO-ENVMON-MIB
•
12.2(18)SXF3
200207170000Z
•
12.2(33)SRA
200207170000Z
•
12.2(33)SRB
200207170000Z
•
12.2(33)SRC
200207170000Z
CISCO-ERM-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200602110000Z
•
12.2(33)SRC
200602110000Z
CISCO-ETHER-CFM-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
•
12.2(33)SRB
200412280000Z
•
12.2(33)SRC
200412280000Z
200412280000Z
CISCO-FLASH-MIB
•
12.2(18)SXF3
200301311234Z
•
12.2(33)SRA
200301311234Z
•
12.2(33)SRB
200403180000Z
•
12.2(33)SRC
200403180000Z
CISCO-FLEX-LINKS-MIB
•
12.2(18)SXF3
200504250000Z
•
12.2(33)SRA
200504250000Z
•
12.2(33)SRB
200504250000Z
•
12.2(33)SRC
200504250000Z
CISCO-FRAME-RELAY-MIB
•
12.2(18)SXF3
200005220000Z
Cisco 7600 Series Router MIB Specifications Guide
3-10
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRA
200005220000Z
•
12.2(33)SRB
200005220000Z
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
200010130000Z
CISCO-FRAS-HOST-MIB
•
12.2(18)SXF3
9703100000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-FTP-CLIENT-MIB
•
12.2(18)SXF3
9710091700Z
•
12.2(33)SRA
9710091700Z
•
12.2(33)SRB
9710091700Z
•
12.2(33)SRC
9710091700Z
CISCO-HSRP-EXT-MIB
•
12.2(18)SXF3
9808030000Z
•
12.2(33)SRA
9808030000Z
•
12.2(33)SRB
9808030000Z
•
12.2(33)SRC
9808030000Z
CISCO-HSRP-MIB
•
12.2(18)SXF3
9808030000Z
•
12.2(33)SRA
9808030000Z
•
12.2(33)SRB
9808030000Z
•
12.2(33)SRC
9808030000Z
CISCO-IETF-ATM2-PVCTRAP-MIB
•
12.2(18)SXF3
200303240000Z
•
12.2(33)SRA
200303240000Z
•
12.2(33)SRB
200303240000Z
•
12.2(33)SRC
9802030000Z
CISCO-IETF-ATM2-PVCTRAP-MIB-EXTN
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200007110000Z
CISCO-IETF-DHCP-SERVER-E
XT-MIB
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-11
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200703151200Z
CISCO-IETF-DHCP-SERVER-M
IB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200703270000Z
CISCO-IETF-FRR-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200211051200Z
•
12.2(33)SRB
200211051200Z
•
12.2(33)SRC
200211051200Z
CISCO-IETF-IP-FORWARD-MIB
•
12.2(18)SXF3
200201240000Z
•
12.2(33)SRA
200201240000Z
•
12.2(33)SRB
200201240000Z
•
12.2(33)SRC
Y
CISCO-IETF-IP-MIB
•
12.2(18)SXF3
200203040000Z
•
12.2(33)SRA
200203040000Z
•
12.2(33)SRB
200203040000Z
•
12.2(33)SRC
Y
CISCO-IETF-ISIS-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
•
12.2(33)SRC
200508161200Z
Y
CISCO-IETF-PPVPN-MPLS-VP
N-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200304171200Z
•
12.2(33)SRB
200304171200Z
•
12.2(33)SRC
200304171200Z
Cisco 7600 Series Router MIB Specifications Guide
3-12
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-IETF-PW-ATM-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200504191200Z
•
12.2(33)SRC
200504191200Z
CISCO-IETF-PW-ENET-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200209221200Z
•
12.2(33)SRB
200209221200Z
•
12.2(33)SRC
200209221200Z
CISCO-IETF-PW-FR-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200312160000Z
•
12.2(33)SRC
200312160000Z
CISCO-IETF-PW-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200403171200Z
•
12.2(33)SRB
200403171200Z
•
12.2(33)SRC
200403171200Z
CISCO-IETF-PW-MPLS-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200302261200Z
•
12.2(33)SRB
200302261200Z
•
12.2(33)SRC
200302261200Z
CISCO-IETF-PW-TC-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200302261200Z
•
12.2(33)SRB
200302261200Z
•
12.2(33)SRC
200302261200Z
CISCO-IETF-PW-TDM-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200607210000Z
•
12.2(33)SRC
200607210000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-13
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-IF-EXTENSION-MIB
•
12.2(18)SXF3
200308120000Z
•
12.2(33)SRA
200308120000Z
•
12.2(33)SRB
200311140000Z
•
12.2(33)SRC
200311140000Z
CISCO-IMAGE-MIB
•
12.2(18)SXF3
9508150000Z
•
12.2(33)SRA
9508150000Z
•
12.2(33)SRB
9508150000Z
•
12.2(33)SRC
9508150000Z
CISCO-IMAGE-TC-MIB
•
12.2(18)SXF3
200501120000Z
•
12.2(33)SRA
200501120000Z
•
12.2(33)SRB
200501120000Z
•
12.2(33)SRC
200501120000Z
CISCO-IP-STAT-MIB
•
12.2(18)SXF3
9707180000Z
•
12.2(33)SRA
200112202300Z
•
12.2(33)SRB
200112202300Z
•
12.2(33)SRC
200112202300Z
CISCO-IP-STAT-MIB
•
12.2(18)SXF3
200012220000Z
•
12.2(33)SRA
200503070000Z
•
12.2(33)SRB
200503070000Z
•
12.2(33)SRC
200503070000Z
CISCO-IP-TAP-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200403110000Z
•
12.2(33)SRC
200403110000Z
CISCO-IP-URPF-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200411120000Z
Cisco 7600 Series Router MIB Specifications Guide
3-14
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-IPSEC-FLOW-MONITOR-MIB
•
12.2(18)SXF3
200010131800Z
•
12.2(33)SRA
200010131800Z
•
12.2(33)SRB
200010131800Z
•
12.2(33)SRC
200010131800Z
CISCO-IPSEC-MIB
•
12.2(18)SXF3
200008071139Z
•
12.2(33)SRA
200008071139Z
•
12.2(33)SRB
200008071139Z
•
12.2(33)SRC
200008071139Z
CISCO-IPSLA-ETHERNET-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200602080000Z
CISCO-L2-CONTROL-MIB
•
12.2(18)SXF3
200306011700Z
•
12.2(33)SRA
200306011700Z
•
12.2(33)SRB
200306011700Z
•
12.2(33)SRC
200306011700Z
CISCO-L2-TUNNEL-CONFIG-MIB
•
12.2(18)SXF3
200205311000Z
•
12.2(33)SRA
200205311000Z
•
12.2(33)SRB
200205311000Z
•
12.2(33)SRC
200205311000Z
CISCO-L2L3-INTERFACE-CONFIG-MIB
•
12.2(18)SXF3
200005101900Z
•
12.2(33)SRA
200005101900Z
•
12.2(33)SRB
200005101900Z
•
12.2(33)SRC
200005101900Z
CISCO-LAG-MIB
•
12.2(18)SXF3
200212130000Z
•
12.2(33)SRA
200212130000Z
•
12.2(33)SRB
200212130000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-15
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
200212130000Z
CISCO-MAC-NOTIFICATION-MIB
•
12.2(18)SXF3
200303210000Z
•
12.2(33)SRA
200303210000Z
•
12.2(33)SRB
200303210000Z
•
12.2(33)SRC
200706110000Z
CISCO-MEMORY-POOL-MIB
•
12.2(18)SXF3
9602120000Z
•
12.2(33)SRA
9602120000Z
•
12.2(33)SRB
9602120000Z
•
12.2(33)SRC
9602120000Z
CISCO-MVPN-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200402231200Z
•
12.2(33)SRB
200402231200Z
•
12.2(33)SRC
200402231200Z
CISCO-NAC-NAD-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200602150000Z
•
12.2(33)SRC
200602150000Z
CISCO-NDE-MIB
•
12.2(18)SXF3
200108080000Z
•
12.2(33)SRA
200108080000Z
•
12.2(33)SRB
200108080000Z
•
12.2(33)SRC
200108080000Z
CISCO-NETFLOW-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
•
12.2(33)SRC
200503270000Z
Y
CISCO-NTP-MIB
•
12.2(18)SXF3
200202200000Z
•
12.2(33)SRA
200307070000Z
•
12.2(33)SRB
200307070000Z
Cisco 7600 Series Router MIB Specifications Guide
3-16
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
200307070000Z
CISCO-OSPF-MIB
•
12.2(18)SXF3
200301280000Z
•
12.2(33)SRA
200301280000Z
•
12.2(33)SRB
200301280000Z
•
12.2(33)SRC
200301280000Z
CISCO-OSPF-TRAP-MIB
•
12.2(18)SXF3
200302270000Z
•
12.2(33)SRA
200302270000Z
•
12.2(33)SRB
200302270000Z
•
12.2(33)SRC
200302270000Z
CISCO-PAE-MIB
•
12.2(18)SXF3
200105241016Z
•
12.2(33)SRA
200302260000Z
•
12.2(33)SRB
200604120000Z
•
12.2(33)SRC
200604120000Z
CISCO-PAGP-MIB
•
12.2(18)SXF3
9903030000Z
•
12.2(33)SRA
9903030000Z
•
12.2(33)SRB
9903030000Z
•
12.2(33)SRC
9903030000Z
CISCO-PIM-MIB
•
12.2(18)SXF3
200011020000Z
•
12.2(33)SRA
200011020000Z
•
12.2(33)SRB
200011020000Z
•
12.2(33)SRC
200011020000Z
CISCO-PING-MIB
•
12.2(18)SXF3
200108280000Z
•
12.2(33)SRA
200108280000Z
•
12.2(33)SRB
200108280000Z
•
12.2(33)SRC
200108280000Z
CISCO-POLICY-GROUP-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200601131600Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-17
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
200601131600Z
CISCO-PORT-SECURITY-MIB
•
12.2(18)SXF3
200504190000Z
•
12.2(33)SRA
200504190000Z
•
12.2(33)SRB
200504190000Z
•
12.2(33)SRC
200504190000Z
CISCO-PPPOE-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200102200000Z
CISCO-PRIVATE-VLAN-MIB
•
12.2(18)SXF3
200207240000Z
•
12.2(33)SRA
200207240000Z
•
12.2(33)SRB
200207240000Z
•
12.2(33)SRC
200207240000Z
CISCO-PROCESS-MIB
•
12.2(18)SXF3
200105180000Z
•
12.2(33)SRA
200301220000Z
•
12.2(33)SRB
200301220000Z
•
12.2(33)SRC
200301220000Z
CISCO-PRODUCTS-MIB
•
12.2(18)SXF3
200204051400Z
•
12.2(33)SRA
200204051400Z
•
12.2(33)SRB
200204051400Z
•
12.2(33)SRC
200505051930Z
CISCO-QINQ-VLAN-MIB
•
12.2(18)SXF3
200411290000Z
•
12.2(33)SRA
200411290000Z
•
12.2(33)SRB
200411290000Z
•
12.2(33)SRC
200411290000Z
CISCO-QLLC01-MIB
•
12.2(18)SXF3
9411090000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
Cisco 7600 Series Router MIB Specifications Guide
3-18
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
Supported and
Unverified
Unsupported or
Unverified
12.2(33)SRC
Not in
Image
Y
CISCO-QUEUE-MIB
•
12.2(18)SXF3
9505310000Z
•
12.2(33)SRA
9505310000Z
•
12.2(33)SRB
9505310000Z
•
12.2(33)SRC
9505310000Z
CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200705220000Z
CISCO-RF-MIB
•
12.2(18)SXF3
200107200000Z
•
12.2(33)SRA
200404030000Z
•
12.2(33)SRB
200404030000Z
•
12.2(33)SRC
200404030000Z
CISCO-RMON-CONFIG-MIB
•
12.2(18)SXF3
200501240000Z
•
12.2(33)SRA
200501240000Z
•
12.2(33)SRB
200602210000Z
•
12.2(33)SRC
200602210000Z
CISCO-RSRB-MIB
•
12.2(18)SXF3
9508210000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-RTTMON-MIB
•
12.2(18)SXF3
0104230000Z
•
12.2(33)SRA
200401200000Z
•
12.2(33)SRB
200603020000Z
•
12.2(33)SRC
200603020000Z
CISCO-RTTMON-IP-EXT-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-19
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
Supported and
Unverified
12.2(33)SRC
Unsupported or
Unverified
Not in
Image
200608020000Z
CISCO-SDLLC-MIB
•
12.2(18)SXF3
9508210000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-SLB-EXT-MIB
•
12.2(18)SXF3
200302111000Z
•
12.2(33)SRA
200302111000Z
•
12.2(33)SRB
200302111000Z
•
12.2(33)SRC
200302111000Z
CISCO-SLB-MIB
•
12.2(18)SXF3
200203180000Z
•
12.2(33)SRA
200203180000Z
•
12.2(33)SRB
200203180000Z
•
12.2(33)SRC
200203180000Z
CISCO-SMI-MIB
•
12.2(18)SXF3
200011012246Z
•
12.2(33)SRA
200011012246Z
•
12.2(33)SRB
200011012246Z
•
12.2(33)SRC
200011012246Z
CISCO-SNADLC-CONV01-MIB
•
12.2(18)SXF3
9504120000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-SNAPSHOT-MIB
•
12.2(18)SXF3
9508150000Z
•
12.2(33)SRA
9508150000Z
•
12.2(33)SRB
9508150000Z
•
12.2(33)SRC
9508150000Z
CISCO-SNMP-TARGET-EXT-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200404010000Z
Cisco 7600 Series Router MIB Specifications Guide
3-20
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
200404010000Z
CISCO-SONET-MIB
•
12.2(18)SXF3
200205220000Z
•
12.2(33)SRA
200205220000Z
•
12.2(33)SRB
200205220000Z
•
12.2(33)SRC
200205220000Z
CISCO-SRP-MIB
•
12.2(18)SXF3
200103280000Z
•
12.2(33)SRA
200103280000Z
•
12.2(33)SRB
200103280000Z
•
12.2(33)SRC
Y
CISCO-STACK-MIB
•
12.2(18)SXF3
200305290000Z
•
12.2(33)SRA
200305290000Z
•
12.2(33)SRB
200305290000Z
•
12.2(33)SRC
200305290000Z
CISCO-STP-EXTENSIONS-MIB
•
12.2(18)SXF3
200503020000Z
•
12.2(33)SRA
200503020000Z
•
12.2(33)SRB
200503020000Z
•
12.2(33)SRC
200503020000Z
CISCO-STUN-MIB
•
12.2(18)SXF3
9508210000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-SVI-AUTOSTATE-MIB
•
12.2(18)SXF3
200311130000Z
•
12.2(33)SRA
200311130000Z
•
12.2(33)SRB
200311130000Z
•
12.2(33)SRC
200311130000Z
CISCO-SWITCH-ENGINE-MIB
•
12.2(18)SXF3
200311070000Z
•
12.2(33)SRA
200311070000Z
•
12.2(33)SRB
200311070000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-21
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
200311070000Z
CISCO-SWITCH-QOS-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200609180000Z
CISCO-SYSLOG-MIB
•
12.2(18)SXF3
9508070000Z
•
12.2(33)SRA
9508070000Z
•
12.2(33)SRB
9508070000Z
•
12.2(33)SRC
9508070000Z
CISCO-TAP2-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200611270000Z
•
12.2(33)SRC
200611270000Z
CISCO-TC
•
12.2(18)SXF3
200404140000Z
•
12.2(33)SRA
200404140000Z
•
12.2(33)SRB
200404140000Z
•
12.2(33)SRC
200404140000Z
CISCO-TCP-MIB
•
12.2(18)SXF3
200111120000Z
•
12.2(33)SRA
200111120000Z
•
12.2(33)SRB
200111120000Z
•
12.2(33)SRC
200111120000Z
CISCO-UDLDP-MIB
•
12.2(18)SXF3
200302210000Z
•
12.2(33)SRA
200302210000Z
•
12.2(33)SRB
200302210000Z
•
12.2(33)SRC
200302210000Z
CISCO-VINES-MIB
•
12.2(18)SXF3
9506070000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
Cisco 7600 Series Router MIB Specifications Guide
3-22
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
Supported and
Unverified
Unsupported or
Unverified
12.2(33)SRC
Not in
Image
Y
CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
•
12.2(18)SXF3
9904010530Z
•
12.2(33)SRA
9904010530Z
•
12.2(33)SRB
9904010530Z
•
12.2(33)SRC
9904010530Z
CISCO-VLAN-MEMBERSHIP-MIB
•
12.2(18)SXF3
200404070000Z
•
12.2(33)SRA
200404070000Z
•
12.2(33)SRB
200404070000Z
•
12.2(33)SRC
200404070000Z
CISCO-VLAN-TRANSLATION-MIB
•
12.2(18)SXF3
200406010000Z
•
12.2(33)SRA
200406010000Z
•
12.2(33)SRB
200406010000Z
•
12.2(33)SRC
200406010000Z
CISCO-VOICE-ANALOG-IF-MIB
•
12.2(18)SXF3
200201210000Z
•
12.2(33)SRA
200201210000Z
•
12.2(33)SRB
200201210000Z
•
12.2(33)SRC
Y
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB
•
12.2(18)SXF3
200109050000Z
•
12.2(33)SRA
200109050000Z
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-VOICE-DIAL-CONTROL-MIB
•
12.2(18)SXF3
200004190000Z
•
12.2(33)SRA
200004190000Z
•
12.2(33)SRB
Not Included
•
12.2(33)SRC
Not Included
CISCO-VOICE-IF-MIB
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-23
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
•
12.2(18)SXF3
9909140000Z
•
12.2(33)SRA
9909140000Z
•
12.2(33)SRB
9909140000Z
•
12.2(33)SRC
Not in
Image
Y
CISCO-VPDN-MGMT-EXT-MI
B
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200706040000Z
CISCO-VPDN-MGMT-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200601200000Z
CISCO-VTP-MIB
•
12.2(18)SXF3
200311210000Z
•
12.2(33)SRA
200311210000Z
•
12.2(33)SRB
200311210000Z
•
12.2(33)SRC
200311210000Z
DIAL-CONTROL-MIB
•
12.2(18)SXF3
9609231544Z
•
12.2(33)SRA
9609231544Z
•
12.2(33)SRB
9609231544Z
•
12.2(33)SRC
Y
DIFFSERV-DSCP-TC
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200205090000Z
•
12.2(33)SRC
200205090000Z
DIFFSERV-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200202070000Z
•
12.2(33)SRC
200202070000Z
DLSW-MIB
Cisco 7600 Series Router MIB Specifications Guide
3-24
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(18)SXF3
9512050000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
DS1-MIB (RFC 1406, 2495,
2495)
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
9808011830Z
•
12.2(33)SRB
9808011830Z
•
12.2(33)SRC
9808011830Z
DS3-MIB (RFC 1407)
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
9808012130
•
12.2(33)SRB
9808012130
•
12.2(33)SRC
9808012130
ENTITY-MIB (RFC 2737)
•
12.2(18)SXF3
9912070000Z
•
12.2(33)SRA
9912070000Z
•
12.2(33)SRB
9912070000Z
•
12.2(33)SRC
9912070000Z
ENTITY-SENSOR-MIB
•
12.2(18)SXF3
200212160000Z
•
12.2(33)SRA
200212160000Z
•
12.2(33)SRB
200212160000Z
•
12.2(33)SRC
200212160000Z
ETHERLIKE-MIB (RFC 2665,
3635)
•
12.2(18)SXF3
9908240400Z
•
12.2(33)SRA
9908240400Z
•
12.2(33)SRB
200309190000Z
•
12.2(33)SRC
200309190000Z
EVENT-MIB
•
12.2(18)SXF3
9902221700Z
•
12.2(33)SRA
200010160000Z
•
12.2(33)SRB
200010160000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-25
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
Supported and
Unverified
12.2(33)SRC
Unsupported or
Unverified
Not in
Image
200010160000Z
EXPRESSION-MIB
•
12.2(18)SXF3
9802251700Z
•
12.2(33)SRA
9802251700Z
•
12.2(33)SRB
9802251700Z
•
12.2(33)SRC
9802251700Z
FR-MFR-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200011300000Z
HC-RMON-MIB
•
12.2(18)SXF3
9702120000Z
•
12.2(33)SRA
9702120000Z
•
12.2(33)SRB
9702120000Z
•
12.2(33)SRC
9702120000Z
IEEE8021-CFM-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200608220100Z
•
12.2(33)SRC
200608220100Z
IEEE8021-PAE-MIB
•
12.2(18)SXF3
200101160000Z
•
12.2(33)SRA
200101160000Z
•
12.2(33)SRB
200101160000Z
•
12.2(33)SRC
200101160000Z
IEEE8023-LAG-MIB
•
12.2(18)SXF3
200006270000Z
•
12.2(33)SRA
200006270000Z
•
12.2(33)SRB
200006270000Z
•
12.2(33)SRC
200006270000Z
IF-MIB (RFC 2863)
•
12.2(18)SXF3
9611031355Z
•
12.2(33)SRA
9611031355Z
•
12.2(33)SRB
9611031355Z
Cisco 7600 Series Router MIB Specifications Guide
3-26
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
9611031355Z
IGMP-MIB
•
12.2(18)SXF3
9712180000Z
•
12.2(33)SRA
9712180000Z
•
12.2(33)SRB
9712180000Z
•
12.2(33)SRC
9712180000Z
IMA-MIB
•
12.2(18)SXF3
9804011315Z
•
12.2(33)SRA
9804011315Z
•
12.2(33)SRB
9804011315Z
•
12.2(33)SRC
9804011315Z
INT-SERV-GUARANTEED-MIB
•
12.2(18)SXF3
9511030500Z
•
12.2(33)SRA
9511030500Z
•
12.2(33)SRB
9511030500Z
•
12.2(33)SRC
9511030500Z
INT-SERV-MIB
•
12.2(18)SXF3
9710030642Z
•
12.2(33)SRA
9710030642Z
•
12.2(33)SRB
9710030642Z
•
12.2(33)SRC
9710030642Z
INTEGRATED-SERVICES-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
9511030500Z
•
12.2(33)SRC
9511030500Z
IP-FORWARD-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
9609190000Z
•
12.2(33)SRB
9609190000Z
•
12.2(33)SRC
200602010000Z
IP-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200404260000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-27
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRC
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
200602020000Z
IPMROUTE-MIB
•
12.2(18)SXF3
9902080000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
IPMROUTE-STD-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200009220000Z
•
12.2(33)SRB
200009220000Z
•
12.2(33)SRC
200009220000Z
LLDP-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200505060000Z
•
12.2(33)SRC
200505060000Z
MPLS-LDP-MIB
•
12.2(18)SXF3
200108161200Z
•
12.2(33)SRA
200108161200Z
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
MPLS-LDP-ATM-STD-MIB
(RFC 3815)
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200406030000Z
•
12.2(33)SRC
200406030000Z
MPLS-LDP-GENERIC-STD-MI
B (RFC 3815)
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200406030000Z
•
12.2(33)SRC
200406030000Z
MPLS-LDP-STD-MIB (RFC
3815)
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
Cisco 7600 Series Router MIB Specifications Guide
3-28
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
•
12.2(33)SRB
200406030000Z
•
12.2(33)SRC
200406030000Z
Unsupported or
Unverified
Not in
Image
MPLS-LSR-MIB
•
12.2(18)SXF3
200004261200Z
•
12.2(33)SRA
200004261200Z
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
MPLS-LSR-STD-MIB (RFC
3031)
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200406030000Z
•
12.2(33)SRC
200406030000Z
MPLS-L3VPN-STD-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
200601230000Z
MPLS-TC-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200101041200Z
•
12.2(33)SRB
200101041200Z
•
12.2(33)SRC
200101041200Z
MPLS-TE-MIB
•
12.2(18)SXF3
200011211200Z
•
12.2(33)SRA
200011211200Z
•
12.2(33)SRB
200011211200Z
•
12.2(33)SRC
200011211200Z
MPLS-VPN-MIB
•
12.2(18)SXF3
200110151200Z
•
12.2(33)SRA
200110151200Z
•
12.2(33)SRB
200110151200Z
•
12.2(33)SRC
200110151200Z
MSDP-MIB
•
12.2(18)SXF3
9912160000Z
•
12.2(33)SRA
9912160000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-29
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
•
12.2(33)SRB
9912160000Z
•
12.2(33)SRC
9912160000Z
Unsupported or
Unverified
Not in
Image
NOTIFICATION-LOG-MIB
•
12.2(18)SXF3
200011270000Z
•
12.2(33)SRA
200011270000Z
•
12.2(33)SRB
200011270000Z
•
12.2(33)SRC
200011270000Z
NOVELL-IPX-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
NOVELL-NLSP-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
NOVELL-RIPSAP-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
OLD-CISCO-APPLETALK-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
OLD-CISCO-CHASSIS-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
Cisco 7600 Series Router MIB Specifications Guide
3-30
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
OLD-CISCO-CPU-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
OLD-CISCO-DECNET-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
OLD-CISCO-INTERFACES-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
OLD-CISCO-IP-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
OLD-CISCO-MEMORY-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-31
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
Not in
Image
OLD-CISCO-NOVELL-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
OLD-CISCO-SYS-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
OLD-CISCO-SYSTEM-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
OLD-CISCO-TCP-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
OLD-CISCO-TS-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
Cisco 7600 Series Router MIB Specifications Guide
3-32
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
Unsupported or
Unverified
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
Not in
Image
OLD-CISCO-VINES-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
OLD-CISCO-XNS-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
OSPF-MIB
•
12.2(18)SXF3
9501201225Z
•
12.2(33)SRA
9501201225Z
•
12.2(33)SRB
9501201225Z
•
12.2(33)SRC
9501201225Z
OSPF-TRAP-MIB
•
12.2(18)SXF3
9501201225Z
•
12.2(33)SRA
9501201225Z
•
12.2(33)SRB
9501201225Z
•
12.2(33)SRC
9501201225Z
PIM-MIB (RFC 2934)
•
12.2(18)SXF3
200009280000Z
•
12.2(33)SRA
200009280000Z
•
12.2(33)SRB
200009280000Z
•
12.2(33)SRC
200009280000Z
RFC1213-MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-33
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
RFC1243-MIB (Appletalk)
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
RFC1315-MIB (Frame Relay)
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
RFC1381-MIB (X25 LAPB)
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
RFC1382-MIB (X25 Packet
Layer)
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
RFC2006-MIB (MIP)
•
12.2(18)SXF3
9606040000Z
•
12.2(33)SRA
9606040000Z
•
12.2(33)SRB
9606040000Z
•
12.2(33)SRC
9606040000Z
RMON-MIB (RFC 1757)
Cisco 7600 Series Router MIB Specifications Guide
3-34
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
RMON2-MIB (RFC 2021)
•
12.2(18)SXF3
9605270000Z
•
12.2(33)SRA
9605270000Z
•
12.2(33)SRB
9605270000Z
•
12.2(33)SRC
9605270000Z
RS-232-MIB
•
12.2(18)SXF3
9405261700Z
•
12.2(33)SRA
9405261700Z
•
12.2(33)SRB
9405261700Z
•
12.2(33)SRC
9405261700Z
RSVP-MIB
•
12.2(18)SXF3
9808251820Z
•
12.2(33)SRA
9808251820Z
•
12.2(33)SRB
9808251820Z
•
12.2(33)SRC
9808251820Z
SMON-MIB
•
12.2(18)SXF3
9812160000Z
•
12.2(33)SRA
9812160000Z
•
12.2(33)SRB
9812160000Z
•
12.2(33)SRC
9812160000Z
SNA-SDLC-MIB
•
12.2(18)SXF3
9411150000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
SNMP-COMMUNITY-MIB
(RFC 2576)
•
12.2(18)SXF3
Revision not
available
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-35
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
SNMP-FRAMEWORK-MIB
(RFC 2571)
•
12.2(18)SXF3
9901190000Z
•
12.2(33)SRA
9901190000Z
•
12.2(33)SRB
9901190000Z
•
12.2(33)SRC
9901190000Z
SNMP-MPD-MIB (RFC 2572)
•
12.2(18)SXF3
9905041636Z
•
12.2(33)SRA
9905041636Z
•
12.2(33)SRB
9905041636Z
•
12.2(33)SRC
9905041636Z
SNMP-NOTIFICATION-MIB
(RFC 2573)
•
12.2(18)SXF3
9808040000Z
•
12.2(33)SRA
9808040000Z
•
12.2(33)SRB
9808040000Z
•
12.2(33)SRC
9808040000Z
SNMP-PROXY-MIB
•
12.2(18)SXF3
9808040000Z
•
12.2(33)SRA
9808040000Z
•
12.2(33)SRB
9808040000Z
•
12.2(33)SRC
9808040000Z
SNMP-TARGET-MIB (RFC
2573)
•
12.2(18)SXF3
9808040000Z
•
12.2(33)SRA
9808040000Z
•
12.2(33)SRB
9808040000Z
•
12.2(33)SRC
9808040000Z
SNMP-USM-MIB (RFC 2574)
•
12.2(18)SXF3
9901200000Z
•
12.2(33)SRA
9901200000Z
Cisco 7600 Series Router MIB Specifications Guide
3-36
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
•
12.2(33)SRB
9901200000Z
•
12.2(33)SRC
9901200000Z
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
SNMP-VACM-MIB (RFC 2575)
•
12.2(18)SXF3
9901200000Z
•
12.2(33)SRA
9901200000Z
•
12.2(33)SRB
9901200000Z
•
12.2(33)SRC
9901200000Z
SNMPV2-MIB (RFC 1907)
•
12.2(18)SXF3
9511090000Z
•
12.2(33)SRA
9511090000Z
•
12.2(33)SRB
9511090000Z
•
12.2(33)SRC
9511090000Z
SONET-MIB (RFC 1595, 2558)
•
12.2(18)SXF3
9401030000Z
•
12.2(33)SRA
9810190000Z
•
12.2(33)SRB
9810190000Z
•
12.2(33)SRC
9810190000Z
SOURCE-ROUTING-MIB (RFC
1525)
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
TCP-MIB
•
12.2(18)SXF3
9411010000Z
•
12.2(33)SRA
9411010000Z
•
12.2(33)SRB
9411010000Z
•
12.2(33)SRC
9411010000Z
TUNNEL-MIB
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200505160000Z
•
12.2(33)SRC
200505160000Z
UDP-MIB
•
12.2(18)SXF3
9411010000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-37
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-1
MIBs in 7600 Series Routers (continued)
Supported and
Verified
MIB
Supported and
Unverified
•
12.2(33)SRA
9411010000Z
•
12.2(33)SRB
9411010000Z
•
12.2(33)SRC
9411010000Z
Unsupported or
Unverified
Not in
Image
Cisco 7600 Series Router MIB Specifications Guide
3-38
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
MIB Notification Names in 7600 Series Routers
Table 3-2 lists the Notification Names associated with MIBs in 7600 Series Routers:
Table 3-2
MIB Notification names in 7600 Series Routers
MIB
Notification Name
BGP4-MIB
bgpEstablished,
bgpBackwardTransition
Supported and
Verified
•
12.2(18)SXF3
9405050000Z
•
12.2(33)SRA
9405050000Z
•
12.2(33)SRB
9405050000Z
•
12.2(33)SRC
9405050000Z
BRIDGE-MIB
Unsupported or
Unverified
Not in
Image
newRoot,
topologyChange
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
CISCO-ALPS-MIB
Supported and
Unverified
alpsPeerStatusChange,
alpsCktStatusChange,
alpsAscuStatusChange,
alpsPeerConnStatusChange,
alpsCktOpenFailure,
alpsCktPartialReject
•
12.2(18)SXF3
200001280000Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-39
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB Notification names in 7600 Series Routers (continued)
MIB
Notification Name
CISCO-ATM-PVCTRAP-EXTN-MIB
catmIntfPvcUpTrap,
catmIntfPvcOAMFailureTrap,
catmIntfPvcSegCCOAMFailureTrap,
catmIntfPvcEndCCOAMFailureTrap,
catmIntfPvcAISRDIOAMFailureTrap,
catmIntfPvcAnyOAMFailureTrap,
catmIntfPvcOAMRecoverTrap,
catmIntfPvcSegCCOAMRecoverTrap,
catmIntfPvcEndCCOAMRecoverTrap,
catmIntfPvcAISRDIOAMRecoverTrap,
catmIntfPvcAnyOAMRecoverTrap,
catmIntfPvcUp2Trap,
catmIntfPvcDownTrap,
catmIntfPvcSegAISRDIFailureTrap,
catmIntfPvcEndAISRDIFailureTrap,
catmIntfPvcSegAISRDIRecoverTrap,
catmIntfPvcEndAISRDIRecoverTrap
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-BGP4-MIB
200303240000Z
cbgpFsmStateChange,
cbgpBackwardTransition,
cbgpPrefixThresholdExceeded,
cbgpPrefixThresholdClear
•
12.2(18)SXF3
200108130000Z
•
12.2(33)SRA
200302240000Z
•
12.2(33)SRB
200302240000Z
•
12.2(33)SRC
200302240000Z
CISCO-BSTUN-MIB
•
bstunPeerStateChangeNotification
12.2(18)SXF3
9701220000Z
Cisco 7600 Series Router MIB Specifications Guide
3-40
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-BULK-FILE-MIB
cbfDefineFileCompletion
•
12.2(18)SXF3
9810291700Z
•
12.2(33)SRA
9810291700Z
•
12.2(33)SRB
9810291700Z
•
12.2(33)SRC
CISCO-CALLHOME-MIB
200108220000Z
ccmSmtpServerFailNotif,
ccmAlertGroupTypeAddedNotif,
ccmAlertGroupTypeDeletedNotif,
ccmSmtpMsgSendFailNotif
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-CAT6K-CROSSBAR-MIB
200704060000Z
cc6kxbarIntBusCRCErrExcdN
otif,
cc6kxbarIntBusCRCErrRcvrdN
otif,
cc6kxbarSwBusStatusChangeN
otif
•
12.2(18)SXF3
200411190000Z
•
12.2(33)SRA
200411190000Z
•
12.2(33)SRB
200411190000Z
•
12.2(33)SRC
200411190000Z
CISCO-CEF-MIB
cefResourceFailure,
cefPeerStateChange,
cefPeerFIBStateChange,
cefInconsistencyDetection
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-CONFIG-COPY-MIB
200601300000Z
ccCopyCompletion
•
12.2(18)SXF3
9701150000Z
•
12.2(33)SRA
200403170000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-41
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
•
12.2(33)SRB
•
12.2(33)SRC
CISCO-CONFIG-MAN-MIB
Supported and
Verified
Not in
Image
200608220000Z
ciscoConfigManEvent,
ccmCLIRunningConfigChanged,
ccmCTIDRolledOver
12.2(18)SXF3
9511280000Z
•
12.2(33)SRA
9511280000Z
•
12.2(33)SRB
200406180000Z
•
12.2(33)SRC
200608220000Z
cdcVFileCollectionError,
cdcFileXferComplete
•
12.2(18)SXF3
•
12.2(33)SRA
200210300530Z
•
12.2(33)SRB
200210300530Z
•
12.2(33)SRC
200210300530Z
CISCO-DLSW-EXT-MIB
Unsupported or
Unverified
200403170000Z
•
CISCO-DATA-COLLECTION-MIB
Supported and
Unverified
Y
cdeTrapTConnUpDown,
cdeTrapCircuitUpDown
•
12.2(18)SXF3
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-DLSW-MIB
9703110000Z
ciscoDlswTrapTConnPartnerReject,
ciscoDlswTrapTConnProtViolation,
ciscoDlswTrapTConnUp,
ciscoDlswTrapTConnDown,
ciscoDlswTrapCircuitUp,
ciscoDlswTrapCircuitDown
•
12.2(18)SXF3
9506300900Z
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
Cisco 7600 Series Router MIB Specifications Guide
3-42
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB Notification names in 7600 Series Routers (continued)
MIB
Notification Name
CISCO-DSPU-MIB
dspuPuStateChangeTrap,
dspuPuActivationFailureTrap,
newdspuPuStateChangeTrap,
newdspuPuActivationFailureTrap,
dspuLuStateChangeTrap,
newdspuLuStateChangeTrap,
dspuLuActivationFailureTrap,
dspuSapStateChangeTrap
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(18)SXF3
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-ENHANCED-MEMORY-POOL-MIB
9508150000Z
cempMemBufferNotify
•
12.2(18)SXF3
200106050000Z
•
12.2(33)SRA
200302240000Z
•
12.2(33)SRB
200302240000Z
•
12.2(33)SRC
200302240000Z
CISCO-ENTITY-ALARM-MIB
ceAlarmAsserted,
ceAlarmCleared
•
12.2(18)SXF3
9907062150Z
•
12.2(33)SRA
9907062150Z
•
12.2(33)SRB
9907062150Z
•
12.2(33)SRC
9907062150Z
CISCO-ENTITY-FRU-CONTROL-MIB
cefcModuleStatusChange,
cefcPowerStatusChange,
cefcFRUInserted,
cefcFRURemoved
•
12.2(18)SXF3
200310230000Z
•
12.2(33)SRA
200310230000Z
•
12.2(33)SRB
200310230000Z
•
12.2(33)SRC
200310230000Z
CISCO-ENTITY-SENSOR-MIB
entSensorThresholdNotification
•
12.2(18)SXF3
200301070000Z
•
12.2(33)SRA
200509080000Z
•
12.2(33)SRB
200601010000Z
•
12.2(33)SRC
200601010000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-43
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB Notification names in 7600 Series Routers (continued)
MIB
Notification Name
CISCO-ENVMON-MIB
ciscoEnvMonShutdownNotification,
ciscoEnvMonFanNotification,
ciscoEnvMonFanStatusChangeNotif,
ciscoEnvMonRedundantSupplyNotification,
ciscoEnvMonSuppStatusChangeNotif,
ciscoEnvMonTemperatureNotification
Supported and
Verified
•
12.2(18)SXF3
200207170000Z
•
12.2(33)SRA
200207170000Z
•
12.2(33)SRB
200207170000Z
•
12.2(33)SRC
200207170000Z
CISCO-ERM-MIB
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
ciscoErmGlobalPolicyViolation,
ciscoErmLocalPolicyViolation
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200602110000Z
•
12.2(33)SRC
200602110000Z
CISCO-ETHER-CFM-MIB
cEtherCfmCcMepUp,
cEtherCfmCcMepDown,
cEtherCfmCcCrossconnect,
cEtherCfmCcLoop,
cEtherCfmCcConfigError,
cEtherCfmXCheckMissing,
cEtherCfmXCheckUnknown,
cEtherCfmXCheckServiceUp
•
12.2(18)SXF3
•
12.2(33)SRA
•
12.2(33)SRB
200412280000Z
•
12.2(33)SRC
200412280000Z
CISCO-FLASH-MIB
Y
200412280000Z
ciscoFlashCopyCompletionTrap,
ciscoFlashDeviceChangeTrap,
ciscoFlashDeviceInsertedNotif,
ciscoFlashDeviceRemovedNotif,
ciscoFlashMiscOpCompletionTrap
Cisco 7600 Series Router MIB Specifications Guide
3-44
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
•
12.2(18)SXF3
200301311234Z
•
12.2(33)SRA
200301311234Z
•
12.2(33)SRB
200403180000Z
•
12.2(33)SRC
200403180000Z
CISCO-FLEX-LINKS-MIB
Unsupported or
Unverified
12.2(18)SXF3
200504250000Z
•
12.2(33)SRA
200504250000Z
•
12.2(33)SRB
200504250000Z
•
12.2(33)SRC
200504250000Z
cHsrpStateChange
•
12.2(18)SXF3
9808030000Z
•
12.2(33)SRA
9808030000Z
•
12.2(33)SRB
9808030000Z
•
12.2(33)SRC
9808030000Z
CISCO-IETF-ATM2-PVCTRAP-MIB-EXTN
Not in
Image
cflIfStatusChangeNotif
•
CISCO-HSRP-MIB
Supported and
Unverified
atmIntfPvcUpTrap,
atmIntfPvcOAMFailureTrap
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-IETF-DHCP-SERVEREXT-MIB
200007110000Z
cDhcpv4ServerIfLeaseLimitEx
ceeded,
cDhcpv4ServerSubnetFreeAddr
essLow,
cDhcpv4ServerSubnetFreeAddr
essHigh
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-IETF-DHCP-SERVERMIB
•
200703151200Z
cDhcpv4ServerFreeAddressLo
w,
cDhcpv4ServerFreeAddressHig
h,
cDhcpv4ServerStartTime,
cDhcpv4ServerStopTime,
cDhcpv4ServerDuplicateAddre
ss
12.2(18)SXF3
Y
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-45
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-IETF-FRR-MIB
200703270000Z
cmplsFrrProtected
•
12.2(18)SXF3
•
12.2(33)SRA
200211051200Z
•
12.2(33)SRB
200211051200Z
•
12.2(33)SRC
200211051200Z
CISCO-IETF-ISIS-MIB
Y
ciiDatabaseOverload,
ciiManualAddressDrops,
ciiCorruptedLSPDetected,
ciiAttemptToExceedMaxSequence,
ciiIDLenMismatch,
ciiMaxAreaAddressesMismatch,
ciiOwnLSPPurge,
ciiSequenceNumberSkip,
ciiAuthenticationTypeFailure,
ciiAuthenticationFailure,
ciiVersionSkew,
ciiAreaMismatch,
ciiRejectedAdjacency,
ciiLSPTooLargeToPropagate,
ciiOrigLSPBuffSizeMismatch,
ciiProtocolsSupportedMismatch,
ciiAdjacencyChange,
ciiLSPErrorDetected
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
•
12.2(33)SRC
200508161200Z
Y
CISCO-IETF-PPVPN-MPLS-V cMplsNumVrfRoPN-MIB
uteMaxThreshCleared
•
12.2(18)SXF3
•
12.2(33)SRA
200304171200Z
•
12.2(33)SRB
200304171200Z
•
12.2(33)SRC
200304171200Z
CISCO-IETF-PW-MIB
Y
cpwVcDown,
cpwVcUp
Cisco 7600 Series Router MIB Specifications Guide
3-46
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
•
12.2(18)SXF3
•
12.2(33)SRA
200403171200Z
•
12.2(33)SRB
200403171200Z
•
12.2(33)SRC
200403171200Z
CISCO-IP-STAT-MIB
Supported and
Unverified
ciscoIpMRouteMissingHeartBeats
12.2(18)SXF3
200012220000Z
•
12.2(33)SRA
200503070000Z
•
12.2(33)SRB
200503070000Z
•
12.2(33)SRC
200503070000Z
clcVlanMacLimitNotif
•
12.2(18)SXF3
200306011700Z
•
12.2(33)SRA
200306011700Z
•
12.2(33)SRB
200306011700Z
•
12.2(33)SRC
200306011700Z
CISCO-MAC-NOTIFICATION-MIB
cmnMacChangedNotification,
cmnMacMoveNotification,
cmnMacThresholdExceedNotif
•
12.2(18)SXF3
200303210000Z
•
12.2(33)SRA
200303210000Z
•
12.2(33)SRB
200303210000Z
•
12.2(33)SRC
CISCO-MVPN-MIB
Not in
Image
Y
•
CISCO-L2-CONTROL-MIB
Unsupported or
Unverified
200706110000Z
ciscoMvpnMvrfChange
•
12.2(18)SXF3
Y
•
12.2(33)SRA
200402231200Z
•
12.2(33)SRB
200402231200Z
•
12.2(33)SRC
200402231200Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-47
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB Notification names in 7600 Series Routers (continued)
MIB
Notification Name
CISCO-OSPF-TRAP-MIB
cospfIfConfigError,
cospfVirtIfConfigError,
cospfTxRetransmit,
cospfVirtIfTxRetransmit,
cospfOriginateLsa,
cospfMaxAgeLsa,
cospfNssaTranslatorStatusChange,
cospfShamLinkStateChange,
cospfShamLinksStateChange,
cospfShamLinkNbrStateChange,
cospfShamLinkConfigError,
cospfShamLinkAuthFailure,
cospfShamLinkRxBadPacket,
cospfShamLinkTxRetransmit
Supported and
Verified
•
12.2(18)SXF3
200302270000Z
•
12.2(33)SRA
200302270000Z
•
12.2(33)SRB
200302270000Z
•
12.2(33)SRC
200302270000Z
CISCO-PAE-MIB
12.2(18)SXF3
200105241016Z
•
12.2(33)SRA
200302260000Z
•
12.2(33)SRB
200604120000Z
•
12.2(33)SRC
200604120000Z
Not in
Image
pimNeighborLoss (RFC 2934),
ciscoPimInterfaceUp,
ciscoPimInterfaceDown,
ciscoPimRPMappingChange,
ciscoPimInvalidRegister,
ciscoPimInvalidJoinPrune
•
12.2(18)SXF3
200011020000Z
•
12.2(33)SRA
200011020000Z
•
12.2(33)SRB
200011020000Z
•
12.2(33)SRC
200011020000Z
CISCO-PING-MIB
Unsupported or
Unverified
cpaeNoGuestVlanNotif,
cpaeNoAuthFailVlanNotif
•
CISCO-PIM-MIB
Supported and
Unverified
ciscoPingCompletion
•
12.2(18)SXF3
200108280000Z
•
12.2(33)SRA
200108280000Z
•
12.2(33)SRB
200108280000Z
•
12.2(33)SRC
200108280000Z
Cisco 7600 Series Router MIB Specifications Guide
3-48
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
CISCO-PORT-SECURITY-MIB cpsIfVlanSecureMacAddrVio-
lation,
cpsSecureMacAddrViolation
•
12.2(18)SXF3
200504190000Z
•
12.2(33)SRA
200504190000Z
•
12.2(33)SRB
200504190000Z
•
12.2(33)SRC
200504190000Z
CISCO-PPPOE-MIB
cPppoeSystemSessionThresholdTrap,
cPppoeVcSessionThresholdTrap
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-PROCESS-MIB
200102200000Z
cpmCPURisingThreshold,
cpmCPUFallingThreshold
•
12.2(18)SXF3
200105180000Z
•
12.2(33)SRA
200301220000Z
•
12.2(33)SRB
200301220000Z
•
12.2(33)SRC
200301220000Z
CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
crepLinkStatus,
crepPreemptionStatus,
crepPortRoleChange
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-RF-MIB
200705220000Z
ciscoRFSwactNotif,
ciscoRFProgressionNotif,
ciscoRFIssuStateNotif
•
12.2(18)SXF3
200107200000Z
•
12.2(33)SRA
200404030000Z
•
12.2(33)SRB
200404030000Z
•
12.2(33)SRC
200404030000Z
CISCO-RSRB-MIB
rsrbPeerStateChangeNotification
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-49
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(18)SXF3
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-RTTMON-MIB
9508210000Z
rttMonConnectionChangeNotification,
ttMonTimeoutNotification,
rttMonThresholdNotification
•
12.2(18)SXF3
0104230000Z
•
12.2(33)SRA
200401200000Z
•
12.2(33)SRB
200603020000Z
•
12.2(33)SRC
200603020000Z
CISCO-SDLLC-MIB
convSdllcPeerStateChangeNotification
•
12.2(18)SXF3
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-SONET-MIB
9508210000Z
ciscoSonetSectionStatusChange,
ciscoSonetLineStatusChange,
ciscoSonetPathStatusChange
•
12.2(18)SXF3
200205220000Z
•
12.2(33)SRA
200205220000Z
•
12.2(33)SRB
200205220000Z
•
12.2(33)SRC
200205220000Z
CISCO-SRP-MIB
srpTrapRingWrapped,
srpTrapRingRestored
•
12.2(18)SXF3
200103280000Z
•
12.2(33)SRA
200103280000Z
•
12.2(33)SRB
200103280000Z
•
12.2(33)SRC
CISCO-STACK-MIB
Y
moduleUp,
moduleDown,
chassisAlarmOn,
chassisAlarmOff
•
12.2(18)SXF3
200305290000Z
•
12.2(33)SRA
200305290000Z
Cisco 7600 Series Router MIB Specifications Guide
3-50
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
•
12.2(33)SRB
200305290000Z
•
12.2(33)SRC
200305290000Z
CISCO-STP-EXTENSIONS-MIB
Unsupported or
Unverified
Not in
Image
stpxInconsistencyUpdate,
stpxLoopInconsistencyUpdate,
stpxRootInconsistencyUpdate
•
12.2(18)SXF3
200503020000Z
•
12.2(33)SRA
200503020000Z
•
12.2(33)SRB
200503020000Z
•
12.2(33)SRC
200503020000Z
CISCO-STUN-MIB
Supported and
Unverified
stunPeerStateChangeNotification
•
12.2(18)SXF3
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-SYSLOG-MIB
9508210000Z
clogMessageGenerated
•
12.2(18)SXF3
9508070000Z
•
12.2(33)SRA
9508070000Z
•
12.2(33)SRB
9508070000Z
•
12.2(33)SRC
9508070000Z
CISCO-TAP2-MIB
ciscoTap2MIBActive,
ciscoTap2MediationTimedOut,
ciscoTap2MediationDebug,
ciscoTap2StreamDebug,
ciscoTap2Switchover
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200611270000Z
•
12.2(33)SRC
200611270000Z
CISCO-VLAN-MEMBERSHIP-MIB
vmVmpsChange
•
12.2(18)SXF3
200404070000Z
•
12.2(33)SRA
200404070000Z
•
12.2(33)SRB
200404070000Z
•
12.2(33)SRC
200404070000Z
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB
•
12.2(18)SXF3
cvdcPoorQoVNotification
200109050000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-51
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(33)SRA
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
CISCO-VPDN-MGMT-MIB
200109050000Z
cvpdnNotifSession
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
CISCO-VTP-MIB
200601200000Z
vtpConfigDigestError,
vtpConfigRevNumberError,
vtpLocalModeChanged,
vlanTrunkPortDynamicStatusChange,
vtpVlanCreated,
vtpVlanDeleted,
vtpVersionInUseChanged,
vtpVersionOneDeviceDetected
•
12.2(18)SXF3
200311210000Z
•
12.2(33)SRA
200311210000Z
•
12.2(33)SRB
200311210000Z
•
12.2(33)SRC
200311210000Z
DIAL-CONTROL-MIB
dialCtlPeerCallInformation,
dialCtlPeerCallSetup
•
12.2(18)SXF3
9609231544Z
•
12.2(33)SRA
9609231544Z
•
12.2(33)SRB
9609231544Z
•
12.2(33)SRC
DLSW-MIB
Y
dlswTrapTConnPartnerReject,
dlswTrapTConnProtViolation,
dlswTrapTConnUp,
dlswTrapTConnDown,
dlswTrapCircuitUp,
dlswTrapCircuitDown
•
12.2(18)SXF3
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
DS1-MIB (RFC 1406, 2495,
2495)
9512050000Z
dsx1LineStatusChange
Cisco 7600 Series Router MIB Specifications Guide
3-52
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
9808011830Z
•
12.2(33)SRB
9808011830Z
•
12.2(33)SRC
9808011830Z
ENTITY-MIB (RFC 2737)
Unsupported or
Unverified
12.2(18)SXF3
9912070000Z
•
12.2(33)SRA
9912070000Z
•
12.2(33)SRB
9912070000Z
•
12.2(33)SRC
9912070000Z
mteTriggerFired,
mteTriggerRising,
mteTriggerFalling,
mteTriggerFailure,
mteEventSetFailure
•
12.2(18)SXF3
9902221700Z
•
12.2(33)SRA
200010160000Z
•
12.2(33)SRB
200010160000Z
•
12.2(33)SRC
200010160000Z
FR-MFR-MIB
Not in
Image
entConfigChange
•
EVENT-MIB
Supported and
Unverified
mfrMibTrapBundleLinkMismatch
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
IEEE8021-CFM-MIB
200011300000Z
dot1agCfmFaultAlarm
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200608220100Z
•
12.2(33)SRC
200608220100Z
IF-MIB (RFC 2863)
linkDown,
linkUp
•
12.2(18)SXF3
9611031355Z
•
12.2(33)SRA
9611031355Z
•
12.2(33)SRB
9611031355Z
•
12.2(33)SRC
9611031355Z
LLDP-MIB
lldpRemTablesChange
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-53
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200505060000Z
•
12.2(33)SRC
200505060000Z
MPLS-LDP-MIB
mplsLdpInitSesThresholdExceeded,
mplsLdpPVLMismatch,
mplsLdpSessionDown
•
12.2(18)SXF3
200108161200Z
•
12.2(33)SRA
200108161200Z
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
MPLS-LDP-STD-MIB (RFC
3815)
mplsLdpInitSessionThresholdExceeded,
mplsLdpPathVectorLimitMismatch,
mplsLdpSessionUp,
mplsLdpSessionDown
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200406030000Z
•
12.2(33)SRC
200406030000Z
MPLS-LSR-MIB
mplsXCUp,
mplsXCDown
•
12.2(18)SXF3
200004261200Z
•
12.2(33)SRA
200004261200Z
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
MPLS-LSR-STD-MIB (RFC
3031)
mplsXCUp,
mplsXCDown
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
200406030000Z
•
12.2(33)SRC
200406030000Z
Cisco 7600 Series Router MIB Specifications Guide
3-54
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB Notification names in 7600 Series Routers (continued)
MIB
Notification Name
MPLS-L3VPN-STD-MIB
mplsL3VpnVrfUp,
mplsL3VpnVrfDown,
mplsL3VpnVrfRouteMidThres
hExceeded,
mplsL3VpnVrfNumVrfRouteM
axThreshExceeded,
mplsL3VpnNumVrfSecIllglLbl
ThrshExcd,
mplsL3VpnNumVrfRouteMax
ThreshCleared
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(18)SXF3
Y
•
12.2(33)SRA
Y
•
12.2(33)SRB
Y
•
12.2(33)SRC
MPLS-TE-MIB
200601230000Z
mplsTunnelDown,
mplsTunnelUp,
mplsTunnelRerouted
•
12.2(18)SXF3
200011211200Z
•
12.2(33)SRA
200011211200Z
•
12.2(33)SRB
200011211200Z
•
12.2(33)SRC
200011211200Z
MPLS-VPN-MIB
mplsNumVrfRouteMidThreshExceeded,
mplsNumVrfRouteMaxThreshExceeded,
mplsNumVrfSecIllegalLabelThreshExceeded,
mplsVrfIfDown,
mplsVrfIfUp
•
12.2(18)SXF3
•
12.2(33)SRA
200110151200Z
•
12.2(33)SRB
200110151200Z
•
12.2(33)SRC
200110151200Z
MSDP-MIB
200110151200Z
msdpEstablished,
msdpBackwardTransition
•
12.2(18)SXF3
9912160000Z
•
12.2(33)SRA
9912160000Z
•
12.2(33)SRB
9912160000Z
•
12.2(33)SRC
9912160000Z
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-55
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB Notification names in 7600 Series Routers (continued)
MIB
Notification Name
OSPF-TRAP-MIB
ospfIfStateChange,
ospfVirtIfStateChange,
ospfNbrStateChange,
ospfVirtNbrStateChange,
ospfIfConfigError,
ospfVirtIfConfigError,
ospfIfAuthFailure,
ospfVirtIfAuthFailure,
ospfIfRxBadPacket,
ospfVirtIfRxBadPacket,
ospfTxRetransmit,
ospfVirtIfTxRetransmit,
ospfOriginateLsa,
ospfMaxAgeLsa,
ospfLsdbOverflow,
ospfLsdbApproachingOverflow
Supported and
Verified
•
12.2(18)SXF3
9501201225Z
•
12.2(33)SRA
9501201225Z
•
12.2(33)SRB
9501201225Z
•
12.2(33)SRC
9501201225Z
PIM-MIB (RFC 2934)
Supported and
Unverified
12.2(18)SXF3
200009280000Z
•
12.2(33)SRA
200009280000Z
•
12.2(33)SRB
200009280000Z
•
12.2(33)SRC
200009280000Z
fallingAlarm,
risingAlarm
•
12.2(18)SXF3
Revision not
available
•
12.2(33)SRA
Revision not
available
•
12.2(33)SRB
Revision not
available
•
12.2(33)SRC
Revision not
available
SNA-SDLC-MIB
•
12.2(18)SXF3
•
12.2(33)SRA
Not in
Image
pimNeighborLoss
•
RMON-MIB (RFC 1757)
Unsupported or
Unverified
sdlcPortStatusChange,
sdlcLSStatusChange,
sdlcLSStatusChange1
9411150000Z
Y
Cisco 7600 Series Router MIB Specifications Guide
3-56
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
Cisco 7600 MIBs
Table 3-2
MIB
MIB Notification names in 7600 Series Routers (continued)
Notification Name
Supported and
Verified
Supported and
Unverified
Unsupported or
Unverified
Not in
Image
•
12.2(33)SRB
Y
•
12.2(33)SRC
Y
Note
The 3rd 12.2(18)SXF rebuild (12.2(18)SXF3) release was used because later releases include features
not supported by c7600 SR releases. Feature parity is up to SXF3.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-57
Chapter 3
Cisco 7600 MIB Specifications
ATM-MIB
ATM-MIB
The ATM-MIB (RFC 1695) contains the ATM and ATM adaptation Layer 5 (AAL5) objects used to
manage logical and physical entities and the relationship between them, such as ATM interfaces, virtual
links, cross connects, and AAL5 entities and connections.
MIB Constraints
Table 3-3 lists the constraints that the Cisco 7600 Series router places on objects in the ATM-MIB. For
detailed definitions of MIB objects, see the MIB.
Table 3-3
ATM-MIB Constraints
MIB Object
Notes
atmInterfaceDs3PlcpTable
Not implemented.
atmInterfaceTCTable
Not implemented.
atmTrafficDescrParamTable
Read-only.
atmVplTable
Not implemented.
atmVclTable
•
atmVclAdminStatus
•
atmVclReceiveTrafficDescrIndex Read-only.
•
atmVclTransmitTrafficDescrIndex Read-only.
•
atmVccAalType
•
atmVccAal5CpcsTransmitSduSize Read-only.
•
atmVccAal5CpcsReceiveSduSize Read-only.
•
atmVccAal5EncapsType
Read-only.
•
atmVclCrossConnectIdentifier
Read-only.
•
atmVclRowStatus
Read-only.
atmVpCrossConnectTable
•
atmVpCrossConnectIndexNext
atmVcCrossConnectTable
•
atmVcCrossConnectIndexNext
Read-only.
Read-only.
Not implemented.
Not implemented.
Not implemented.
Not implemented.
* The ifType for the ifIndex used in the ATM-MIB tables must be type atm(37).
BGP4-MIB
The BGP4-MIB (RFC 1657) provides access to information related to the implementation of the Border
Gateway Protocol (BGP). The MIB provides:
•
BGP configuration information
•
Information about BGP peers and messages exchanged with them
•
Information about advertised networks
Cisco 7600 Series Router MIB Specifications Guide
3-58
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
BRIDGE-MIB
BRIDGE-MIB
The BRIDGE-MIB contains objects to manage Media Access Control (MAC) bridges between Local
Area Network (LAN) segments, as defined by the IEEE 802.1D-1990 standard. This MIB is extracted
from RFC 1493 and is intended for use with network management protocols in TCP/IP based internets.
CISCO-802-TAP-MIB
The CISCO-802-TAP-MIB contains object to manage IEEE 802 intercept.
CISCO-AAA-SESSION-MIB
The CISCO-AAA-SESSION-MIB contains information about accounting sessions based on
authentication, authorization, and accounting (AAA) protocols.
CISCO-AAL5-MIB
The CISCO-AAL5-MIB contains performance statistics for ATM adaptation Layer 5 (AAL5) virtual
channel connections (VCCs). This MIB provides statistics not found in the aal5VccTable in RFC 1695
(for example, packets and octets received and transmitted on the VCC).
CISCO-ACCESS-ENVMON-MIB
The CISCO-ACCESS-ENVMON-MIB indicates the reason for a power supply failure, which is
information that is not provided in the ciscoEnvMonSupplyStatusTable in the CISCO-ENVMON-MIB.
The CISCO-ACCESS-ENVMON-MIB also defines temperature and voltage notifications to replace
those in CISCO-ENVMON-MIB.
CISCO-ALPS-MIB
The CISCO-ALPS-MIB provides Cisco airline protocol support for IBM-P1024B(ALC) and
Unisys-P1024C(UTS) protocol encapsulation over TCP/IP. The MIB contains configuration and
operational information for the protocol, which provides a tunneling mechanism to transport airline
protocol data across a Cisco router-based TCP/IP network to an X.25-attached mainframe.
CISCO-ASPP-MIB
The CISCO-ASPP-MIB provides configuration and operational information on asynchronous-polled
protocols such as the asynchronous security protocols that alarm monitoring companies use.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-59
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ATM-EXT-MIB
CISCO-ATM-EXT-MIB
The CISCO-ATM-EXT-MIB contains extensions to the Cisco ATM module that are used to manage
ATM entities. It provides additional AAL5 performance statistics for a virtual channel connection (VCC)
on an ATM interface.
Note
The cAal5VccExtTable augments the aal5VccTable of the ATM-MIB. The aal5VccTable contains
additional AAL5 performance parameters.
CISCO-ATM-PVC-MIB
The CISCO-ATM-PVC-MIB contains objects to configure a permanent virtual circuit (PVC) on an
ATM uplink card, and bind the PVC to a virtual LAN (VLAN). This allows the PVC to carry bridged
PDUs (BPDUs) using the encapsulation method described in RFC 1483, which is an alternative to using
LAN emulation to transfer BPDUs.
CISCO-ATM-PVCTRAP-EXTN-MIB
The CISCO-ATM-PVCTRAP-EXTN-MIB supplements to the CISCO-IETF-ATM2-PVCTRAP-MIB.
CISCO-ATM-QOS-MIB
The CISCO-ATM-QOS-MIB is created to provide ATM QoS information in the following areas:
•
Traffic shaping on a per-VC basis
•
Traffic shaping on a per-VP basis
•
Per-VC queuing/buffering.
CISCO-BCP-MIB
The CISCO-BCP-MIB (based on RFC 2878) (Bridging Control Protocol) contains objects to configure,
enable, and disable bridge modules on both ends of point-to-point links. The Cisco 7600 series Internet
router uses the BCP for transporting Ethernet frames over SONET and DPT networks. The BCP-MIB
manages and monitors Bridge Control Protocol configuration and information on subnetwork interfaces
using the family of Point-to-Point Protocols.
MIB Constraints
Table 3-4 lists the constraints that the router places on objects in the CISCO-BCP-MIB. For detailed
definitions of MIB objects, see the MIB.
Cisco 7600 Series Router MIB Specifications Guide
3-60
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-BGP-POLICY-ACCOUNTING-MIB
Table 3-4
CISCO-BCP-MIB Constraints
MIB Object
Notes
bcpConfigTable
•
bcpConfigBridgeIdControl
Read-only. Always disabled
•
bcpConfigBridgeId
Always 0. BcpConfigBridgeIdControl must be enabled
to have value.
•
bcpConfigLineIdControl
Read-only. Always disabled
•
bcpConfigLineId
Always 0. BcpConfigLineIdControl must be enabled to
have value.
•
bcpConfigMacSupport
Read-only. Always disabled
•
bcpConfigMacType
Always 0. BcpConfigMacControl must be enabled to
have value.
•
bcpConfigTinygram
Read-only. Always disabled
•
bcpConfigMacAddressControl
Read-only. Always disabled
•
bcpConfigMacAddress
Read-only. Always 0000.0000.0000, since this is
meaningful only if BcpConfigMacAddressControl is
enabled.
•
bcpConfigSpanTreeControl
Read-only. Always disabled
•
bcpConfigSpanTree
Read-only. Always null (0).
BcpConfigSpanTreeControl must be enabled to have
value.
* If there is an entry in the ifTable with ifType ppp(23), there will be an entry in both the bcpOperTable and
bcpConfigTable.
* The CISCO-BCP-MIB supports interfaces configured with bridge-enabled only, which means if no “bridge-enable” is
configured, there will be no such entry for this interface when the user pulls the bcpOperTable or bcpConfigTable
by SNMP.
CISCO-BGP-POLICY-ACCOUNTING-MIB
The CISCO-BGP-POLICY-ACCOUNTING-MIB contains BGP policy-based accounting information
(such as ingress traffic on an interface), which can be used for billing purposes. The MIB provides
support for BGP Policy Accounting, which enables you to classify IP traffic into different classes and to
maintain statistics for each traffic class.
The MIB contains counts of the number of bytes and packets of each traffic type on each input interface.
This information can be used to charge customers according to the route that their traffic travels.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-61
Chapter 3
Cisco 7600 MIB Specifications
CISCO-BGP4-MIB
CISCO-BGP4-MIB
The CISCO-BGP4-MIB provides access to information related to the implementation of the Border
Gateway Protocol (BGP). The MIB provides:
•
BGP configuration information
•
Information about BGP peers and messages exchanged with them
•
Information about advertised networks
CISCO-BRIDGE-EXT-MIB
The CISCO-BRIDGE-EXT-MIB extends the BRIDGE-MIB specified in RFC 1493.
CISCO-BSC-MIB
The CISCO-BSC-MIB contains objects to manage binary synchronous communications (BSC) on the
router, including BSC ports (serial interfaces) and BSC control units (stations on a port).
CISCO-BSTUN-MIB
The CISCO-BSTUN-MIB contains objects to manage Block Serial Tunnels (BSTUNs) on the router.
The MIB provides global BSTUN information and contains configuration and operational information
to manage BSTUN groups, ports, and routes.
CISCO-BULK-FILE-MIB
The CISCO-BULK-FILE-MIB contains objects to create and delete files of SNMP data for bulk-file
transfer.
MIB Constraints
Table 3-5 lists the constraints that the router places on objects in the CISCO-BULK-FILE-MIB. For detailed
definitions of MIB objects, see the MIB.
Table 3-5
CISCO-BULK-FILE-MIB Constraints
MIB Object
Notes
cbfDefineFileTable
•
cbfDefinedFileStorage
Only ephemeral type of file storage is supported.
Note
The ephemeral bulk file created can be moved to
a remote FTP server using
CISCO-FTP-CLIENT-MIB.
Cisco 7600 Series Router MIB Specifications Guide
3-62
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-CABLE-DIAG-MIB
Table 3-5
CISCO-BULK-FILE-MIB Constraints
MIB Object
•
cbfDefinedFileFormat
Notes
Only bulkBinary and bulkASCII file formats are
supported.
Note:
The cbfDefienFileTable has objects that are required for defining a bulk file and for controlling its creation. The
cbfDefineObjectTable has information regarding the contents (SNMP data) that go into the bulk file.
When an entry in the cbfDefineFileTable and its corresponding entries in the cbfDefineObjectTable are active, then
cbfDefineFileNow can then be set to create. This causes a bulkFile to be created as defined in cbfDefineFileTable
and it will also create an entry in the cbfStatusFileTable.
CISCO-CABLE-DIAG-MIB
The CISCO-CABLE-DIAG-MIB module defines objects for managing cable diagnostic test capabilities
supported by the Cisco devices.
Cable diagnostic tests are tests intended to exercise the functional integrity of the cable attached to a
physical interface
CISCO-CALLHOME-MIB
The CISCO-CALLHOME-MIB module provides functionality to manage Call Home feature within the
framework of Call Home architecture.
A customer might be deploying network solutions to run mission critical applications such as storage
solutions that require high availability. Such customers need runtime support for their networking
products. Cisco Call Home feature enables a system experiencing Hardware/Software problem to
automatically send relevant failure information to the Support Center. The Support Center can use this
information to provide immediate help in the form of troubleshooting or hardware replacement. This
feature also provides functionality that allow storage systems to send performance, accounting, and
system health information.
CISCO-CAR-MIB
The CISCO-CAR-MIB contains information about the Committed Access Rate (CAR) assigned to router
interfaces. The CAR is used to control the rate of traffic on an interface for packet switching purposes.
The MIB provides information about how the router is to handle traffic that conforms and exceeds the
CAR on the interface.
CISCO-CASA-FA-MIB
The CISCO-CASA-FA-MIB is used in conjunction with the CISCO-CASA-MIB to manage a
Cisco Appliance Services Architecture (CASA) forwarding agent (FA).
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-63
Chapter 3
Cisco 7600 MIB Specifications
CISCO-CASA-MIB
The CASA protocol allows appliances (software entities such as web caches, firewalls, and load
balancers) to control the behavior of forwarding agents (hardware devices such as switches and routers).
The appliance tells forwarding agents how to handle packets based on their source and destination
IP addresses and ports, and IP protocol fields (this information is called an affinity).
CISCO-CASA-MIB
The CISCO-CASA-MIB contains objects to manage a Cisco Appliance Services Architecture (CASA)
entity (such as a manager or a forwarding agent). The MIB contains objects to configure CASA, and to
retrieve status and operational information about the fixed affinity cache.
The CASA protocol allows appliances (software entities such as web caches, firewalls, and load
balancers) to control the behavior of forwarding agents (hardware devices such as switches and routers).
The appliance tells forwarding agents how to handle packets based on their source and destination
IP addresses and ports, and IP protocol fields (this information is called an affinity).
CISCO-CAT6K-CROSSBAR-MIB
The CISCO-CAT6K-CROSSBAR-MIB contains objects to configure and manage the crossbar-switching
fabric module on Cisco Catalyst 6500 family switches.
CISCO-CDP-MIB
The CISCO-CDP-MIB contains objects to manage the Cisco Discovery Protocol (CDP) on the router.
CISCO-CEF-MIB
The CISCO-CEF-MIB contains objects to configure and monitor CEF related objects.
CISCO-CIRCUIT-INTERFACE-MIB
The CISCO-CIRCUIT-INTERFACE-MIB contains objects to configure the circuit description for an
interface. The circuit description identifies circuits on interfaces such as ATM and Frame Relay, and
might be used, for example, to correlate performance statistics on the corresponding interfaces.
CISCO-CLASS-BASED-QOS-MIB
The CISCO-CLASS-BASED-QOS-MIB provides only read access to quality of service
(QoS) configuration information and statistics for Cisco platforms that support the modular Quality of
Service command-line interface (modular QoS CLI).
To understand how to navigate the CISCO-CLASS-BASED-QOS-MIB tables, it is important to
understand the relationship among different QoS objects. QoS objects consists of:
•
Match Statement – the specific match criteria to identify packets for classification purposes.
Cisco 7600 Series Router MIB Specifications Guide
3-64
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-CONFIG-COPY-MIB
•
Class Map – a user-defined traffic class that contains 1 or more match statements used to classify
packets into different categories.
•
Feature Action – a QoS feature. Features include police, traffic shaping, queueing, random detect,
and packet marking. After the traffic has been classified we apply actions to each traffic class.
•
Policy Map – a user-defined policy that associates a Qos feature action to the user-define class map.
•
Service Policy – a policy map that has been attached to an interface.
The MIB uses the following indices to identify QoS features and distinguish among instances of those
features:
•
cbQosObjectsIndex – identifies each QoS feature on the router.
•
cbQoSConfigIndex n- identifies a type of QoS configuration. This index is shared by QoS objects
that have identical configuration.
•
cbQosPolicyIndex – uniquely identifies a service policy.
QoS MIB information is stored in:
•
Configuration instances – includes all class maps, policy map, match statements, and feature action
configuration parameters. Might have multiple identical instances. Multiple instances of the same
QoS feature share a single configuration object, which is identified by cbQosConfigIndex.
•
Runtime Statistics instances—Includes summary counts and rates by traffic class before and after
any configured QoS policies are enforced. In addition, detailed feature-specific statistics are
available for select PolicyMap features. Each has a unique runtime instance. Multiple instances of
a QoS feature have a separate statistics object. Run-time instances of QoS objects are each assigned
a unique identifier (cbQosObjectsIndex) to distinguish among multiple objects with matching
configurations.
CISCO-CONFIG-COPY-MIB
The CISCO-CONFIG-COPY-MIB contains objects to copy configuration files on the router. For
example, the MIB enables the SNMP agent to copy:
•
Configuration files to and from the network
•
The running configuration to the startup configuration and startup to running
•
The startup or running configuration files to and from a local Cisco IOS file system
CISCO-CONFIG-MAN-MIB
The CISCO-CONFIG-MAN-MIB contains objects to track and save changes to the router configuration.
The MIB represents a model of the configuration data that exists elsewhere in the router and in peripheral
devices. Its main purpose is to report changes to the running configuration through the
SNMP notification ciscoConfigManEvent.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-65
Chapter 3
Cisco 7600 MIB Specifications
CISCO-CONTEXT-MAPPING-MIB
CISCO-CONTEXT-MAPPING-MIB
The CISCO-CONTEXT-MAPPING-MIB module provides mapping tables which contain the
information that a single SNMP agent sometimes needs to support multiple instances of the same MIB
module. In such cases, network management applications need to know the specific data/identifier values
in each context. This is accomplished through the use of multiple SNMP contexts.
CISCO-CSG-MIB
The CISCO-CSG-MIB supports the Cisco Content Services Gateway (CSG) product. It includes five
traps and four tables that enable querying CSG resource statistics.
CISCO-DATA-COLLECTION-MIB
The CISCO-DATA-COLLECTION-MIB retrieves data periodically when the data displays as a set of
discontinuous rows spread across multiple tables. This MIB module facilitates data retrieval of tabular
objects. This MIB can be used for performance and accounting purposes, where several row instances
of a set of objects are polled over a period of time.
The MIB provides the user a way to specify which objects and which instances are required. In addition
the MIB provides 2 ways in which this data can be retrieved.
MIB Constraints
Table 3-6 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-DATA-COLLECTION-MIB. For detailed definitions of MIB objects, see the MIB. Any MIB
table or object not listed in this table is implemented as defined in the MIB.
Note
Only traps are supported by the CISCO-DATA-COLLECTION-MIB.
Table 3-6
CISCO-DATA-COLLECTION-MIB Constraints
MIB Object
Notes
cdcVFileTable
Not implemented.
cdcVFileMgmtTable
Not implemented.
cdcDGTable
Not implemented.
cdcDGBaseObjectTable
Not implemented.
cdcDGInstanceTable
Not implemented.
cdcFileXferConfTable
Not implemented.
•
cdcVFilePersistentStorage
•
cdcVFileMaxSizeHitsLimit.
These objects are not implemented.
Cisco 7600 Series Router MIB Specifications Guide
3-66
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-DIAL-CONTROL-MIB
CISCO-DIAL-CONTROL-MIB
The CISCO-DIAL-CONTROL-MIB stores past call information. This MIB is an extension of RFC 2128.
CISCO-DLCSW-MIB
The CISCO-DLCSW-MIB contains objects to manage Frame-Relay access support (FRAS) sessions to
the end-user station. The MIB applies only to downstream or end-user sessions. It does not apply to
upstream or host-end sessions, which are managed through the FRAS-HOST-MIB.
CISCO-DLSW-EXT-MIB
The CISCO-DLSW-EXT-MIB is an extension to the CISCO-DLSW-MIB. It contains objects to manage
Cisco specific data-link switching (DLSw) protocol enhancements. DLSW provides a way to transport
Systems Network Architecture (SNA) and NetBIOS traffic over an IP network.
CISCO-DLSW-MIB
The CISCO-DLSW-MIB contains objects to manage Data Link Switches.
CISCO-DSPU-MIB
The CISCO-DSPU-MIB contains objects to configure and manage Cisco downstream physical
unit (DSPU) objects.
CISCO-EIGRP-MIB
The CISCO-EIGRP-MIB contains objects to manage Enhanced Interior Gateway Protocol (EIGRP).
EIGRP is a Cisco proprietary distance vector routing protocol, based on the Diffusing Update Algorithm
(DUAL). DUAL defines the method to identify loop-free paths through a network.
CISCO-EMBEDDED-EVENT-MGR-MIB
The CISCO-EMBEDDED-EVENT-MGR-MIB provides descriptions and stores events generated by the
Cisco Embedded Event Manager. The Cisco Embedded Event Manager detects hardware and software
faults and other events such as OIRs for the system.
CISCO-ENHANCED-IMAGE-MIB
The CISCO-ENHANCED-IMAGE-MIB provides information about events running on the system. The
MIB modular operating systems.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-67
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENHANCED-MEMORY-POOL-MIB
CISCO-ENHANCED-MEMORY-POOL-MIB
The CISCO-ENHANCED-MEMORY-POOL-MIB contains objects to monitor memory pools on all of
the physical entities on a managed system. Represents the different types of memory pools that may be
present in a managed device. Memory use information is provided to users at three different intervals of
time: 1 minute, 5 minutes, and 10 minutes. Memory pools can be categorized into two groups, predefined
pools and dynamic pools. The following pool types are currently predefined:
•
1:Processor memory
•
2:I/O memory
•
3:PCI memory
•
4:Fast memory
•
5:Multibus memory
Dynamic pools have a pool type value greater than any of the predefined types listed above. Only the
processor pool is required to be supported by all devices. Support for other pool types is dependent on
the device being managed. For detailed definitions of the CISCO-ENHANCED-MEMORY-POOL-MIB
objects, see the MIB.
MIB Constraints
Table 3-7 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-ENHANCED-MEMORY-POOL-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-7
CISCO-ENHANCED-MEMORY-POOL-MIB Constraints
MIB Object
Notes
ciscoMemoryPoolTable
•
cempMemPoolType
Values are:
•
processorMemory(2)
•
ioMemory(3)
•
cempMemPoolAlternate
Always 0.
•
cempMemPoolPlatformMemory
Always 0.
MIB Usage Values for Cisco FlexWAN and FlexWAN2 Cards
There are two types of memory available on the Enhanced FlexWAN cards, processor and PCI. Only the
processorMemory(2) and ioMemory (3) pool types are supported. Table 3-8 lists the memory pool names
corresponding to each pool type:
Cisco 7600 Series Router MIB Specifications Guide
3-68
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-8
CISCO-ENHANCED-MEMORY-POOL-MIB Usage Values in the cempMemPoolTable
cempMemPoolType
processorMemory
ioMemory
cempMemPoolName
•
Processor 0
•
Processor 1
•
I/O is 0
•
I/O is 1
CISCO-ENTITY-ALARM-MIB
The CISCO-ENTITY-ALARM-MIB enables the Cisco 7600 Series router to monitor alarms generated
by system components, such as the chassis, slots, modules, power supplies, fans, and ports.
MIB Constraints
Table 3-9 lists the constraints that the Cisco 7600 Series router WAN modules place on objects in the
CISCO-ENTITY-ALARM-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-9
CISCO-ENTITY-ALARM-MIB Constraints
MIB Object
Notes
ceAlarmTable
•
ceAlarmFilterProfile
Not implemented.
•
ceAlarmFilterProfileIndexNext
Not implemented.
ceAlarmFilterProfileTable
Not implemented.
ceAlarmDescrTable
ceAlarmDescrSeverity
Read-only.
ENTITY-MIB Table, entPhysicalTable, identifies the physical system components in the router. The
following list describes the table objects that describe the alarms for the CISCO-ENTITY-ALARM-MIB:
•
Physical entity—The component in the Cisco 7600 router that generates the alarm.
•
ceAlarmDescrVendorType—The object specifies an identifier (typically an enterprise-specific OID)
that uniquely identifies the vendor type of those physical entities that this alarm description applies
to.
•
Alarm severity—Each alarm type defined by a vendor type and employed by the system is assigned
an associated severity:
– Critical—Indicates a severe, service-affecting condition has occurred and that immediate
corrective action is imperative, regardless of the time of day or day of the week. For example,
online insertion and removal or loss of signal failure when a physical port link is down.
– Major—Used for hardware or software conditions. Indicates a serious disruption of service or
the malfunctioning or failure of important hardware. Requires immediate attention and response
of a technician to restore or maintain system stability. The urgency is less than in critical
situations because of a lesser effect on service or system performance.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-69
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-ALARM-MIB
– Minor—Used for troubles that do not have a serious effect on service to customers or for alarms
in hardware that are not essential to the operation of the system.
– Info—Notification about a condition that could lead to an impending problem or notification of
an event that improves operation.
The syntax values are: critical(1), major(2), minor(3), info(4)
•
Alarm description text—Specifies a readable message describing the alarm.
•
Alarm type—Identifies the type of alarm that is generated. An arbitrary integer value that uniquely
identifies an event relative to a physical entity in the Cisco 7600 router. Values 0 through 255.
Table 3-10 lists the alarm descriptions and severity levels for the Cisco 7600 router FlexWAN PA T3/E3
ports.
Table 3-10
Alarms Supported for Cisco 7600 Router FlexWAN PA T3/E3 Ports
Physical Entity
ceAlarmDescrVendorType
FlexWAN PA T3/3E
ports
cevPortT3
cevPortE3
cevPortDsE3Atm
ceAlarmDescr
Severity
ceAlarmDescrText
major
Transmitter is sending remote
alarm
major
Transmitter is sending AIS
major
Receiver has loss of signal
major
Receiver is receiving AIS
major
Receiver has loss of frame
major
Receiver has remote alarm
major
Receiver has idle signal
major
Other failure
major
Physical port link down
info
Physical port administrative
state down
Table 3-11 lists the alarm descriptions and severity levels for the Cisco 7600 router ATM and packet over
SONET ports.
Table 3-11
Alarms Supported for Cisco 7600 Router ATM and POS Ports
Physical Entity
ATM and POS ports
ceAlarmDescr
ceAlarmDescrVendorType Severity
cevPortATM
cevPortPOS
cevPortChSonet
ceAlarmDescrText
critical
Section loss of signal failure
critical
Section loss of frame failure
critical
Section out of frame alignment
minor
J0 trace byte mismatch
minor
Section bit interleaved parity
major
Line alarm indication signal
Cisco 7600 Series Router MIB Specifications Guide
3-70
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-11
Physical Entity
Alarms Supported for Cisco 7600 Router ATM and POS Ports (continued)
ceAlarmDescr
ceAlarmDescrVendorType Severity
ceAlarmDescrText
major
Line remote failure indication
minor
Line bit interleaved parity
minor
Line far end block errors
critical
Path alarm indication signal
critical
Path remote failure indication
critical
Path loss of pointer
minor
Path bit interleaved parity
minor
Path far end block errors
minor
Protection switching byte
failure
minor
Path pointer justifications
minor
Path positive pointer stuff event
minor
Path negative pointer stuff
event
major
Path payload label mismatch
major
Path unequipped payload label
zero
minor
Path trace identifier mismatch
minor
Path trace identifier unstable
minor
Count of number of times APS
bytes changed
minor
Receiver data out of lock
critical
Signal failure alarm
critical
Signal degrade alarm
minor
Signal failure alarm and B3
errors
minor
Signal degrade alarm and B3
errors
critical
Threshold cross alarm–B1
critical
Threshold cross alarm–B2
critical
Threshold cross alarm–B3
critical
Loss of multiframe
Table 3-12 lists the alarm descriptions and severity levels for the Cisco 7600 router serial port adapters.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-71
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-ALARM-MIB
Table 3-12
Alarms Supported for Cisco 7600 Router Serial Port Adapters
Physical Entity
ceAlarmDescrVendorType
Serial port adapter
ports
cevPortHSSI
cevPortCBusSerial
ceAlarmDescr
Severity
ceAlarmDescrText
minor
Physical port link down
Info
Physical port administrative
state down
Table 3-13 lists the alarm descriptions and severity levels for the Cisco 7600 router FlexWAN PA T1 and
E1 ports.
Table 3-13
Alarms Supported for Cisco 7600 Router FlexWAN PA T1/E1 Port Adapter Ports
Physical Entity
ceAlarmDescr
ceAlarmDescrVendorType Severity
ceAlarmDescrText
FlexWAN PA T1
and E1 ports
cevPortT1
cevPortE1
minor
Transmitter is sending remote
alarm
minor
Transmitter is sending AIS
minor
Transmitter is sending TS16
LOMF alarm
minor
Receiver has loss of multiframe in
TS16
minor
Receiver has loss of signal
minor
Receiver is receiving AIS
minor
Receiver has loss of frame
minor
Receiver has remote alarm
minor
Receiver is getting AIS in TS16
minor
Receiver has remote TS16 LOMF
alarm
minor
Other failure
minor
Physical port link down
info
Physical port administrative state
down
Cisco 7600 Series Router MIB Specifications Guide
3-72
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-ASSET-MIB
Table 3-14 lists the alarm descriptions and severity levels for the Cisco 7600 router FlexWAN
T1/E1 IMA ports.
Table 3-14
Alarms Supported for Cisco 7600 Router FlexWAN T1/E1 IMA Ports
Physical Entity
ceAlarmDescrVendorType
FlexWAN T1/E1
IMA ports
cevPortT1ImaLink
cevPortE1ImaLink
ceAlarmDescr
Severity
ceAlarmDescrText
minor
Transmitter is sending remote
alarm
minor
Transmitter is sending AIS
minor
Receiver has loss of signal
minor
Receiver is receiving AIS
minor
Receiver has loss of frame
minor
Receiver has remote alarm
minor
Other failure
minor
Physical port link down
info
Physical port administrative
state down
CISCO-ENTITY-ASSET-MIB
The CISCO-ENTITY-ASSET-MIB provides asset tracking information for the physical components in
the ENTITY-MIB (RFC2737) entPhysicalTable.
The ceAssetTable contains an entry (ceAssetEntry) for each physical component on the router. Each
entry provides information about the component, such as its orderable part number, serial number,
hardware revision, manufacturing assembly number, and manufacturing revision.
Most physical components are programmed with a standard Cisco generic ID PROM value that specifies
asset information for the component. If possible, the MIB accesses the component’s ID PROM
information.
MIB Constraints
Table 3-15 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-ENTITY-ASSET-MIB.
Table 3-15
MIB Object
CISCO-ENTITY-ASSET-MIB Object Constraints
Notes
ceAssetTable
ceAssetOrderablePartNumber
Not implemented
ceAssetSerialNumber
Not implemented
ceAssetHardwareRevision
Not implemented
ceAssetFirmwareRevision
Not implemented
ceAssetsSoftwareRevision
Not implemented
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-73
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-EXT-MIB
MIB Object
Notes
ceAssetAlias
Not implemented
ceAssetTag
Not implemented
ceAssetIsFRU
Not implemented
CISCO-ENTITY-EXT-MIB
The CISCO-ENTITY-EXT-MIB contains extensions for the processor modules listed in the
ENTITY-MIB entPhysicalTable. A processor module is any physical entity that has a CPU, RAM, and
NVRAM, and can load a boot image and save a configuration. The extensions in this MIB provide
information such as RAM and NVRAM sizes, configuration register settings, and bootload image name
for each processor module.
CISCO-ENTITY-FRU-CONTROL-MIB
The CISCO-ENTITY-FRU-CONTROL-MIB contains objects to configure and monitor the status of
field replaceable units (FRUs) on the Cisco 7600 Series router listed in the ENTITY-MIB
entPhysicalTable. An FRU is a hardware component (such as a line card and module, fan, or power
supply) that can be replaced on site. This MIB is applicable to SIP and SPA modules for this release.
MIB Constraints
Table 3-16 lists the constraints that the router places on objects in the
CISCO-ENTITY-FRU-CONTROL-MIB.
Table 3-16
CISCO-ENTITY-FRU-CONTROL-MIB Constraints
MIB Object
Notes
cefcModuleTable
•
cefcModuleAdminStatus
enabled(1) for read and write.
reset(3) for write only.
•
cefcModuleOperStatus
unknown(1)
ok(2)
failed(7)
•
cefcModuleResetReason
unknown(1)
powerUp(2)
manualReset(5)
•
cefcModuleLastClearConfigTime
Not implemented.
•
cefcModuleResetReasonDescription Not implemented.
•
cefcModuleStateChangeReasonDescr Not implemented.
•
cefcModuleUpTime
Not implemented.
cefcModuleTable
cefcFRUPowerStatusTable
Cisco 7600 Series Router MIB Specifications Guide
3-74
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-SENSOR-MIB
CISCO-ENTITY-SENSOR-MIB
The CISCO-ENTITY-SENSOR-MIB contains objects that support the monitoring of sensors. The MIB
is applicable to sensors present in various modules and to the sensors present in the DWDM GBICs and
XENPAK transceivers. This MIB allows you to monitor sensor values and thresholds on sensors that are
discovered by the ENTITY-MIB.
MIB Constraints
Table 3-17 lists CISCO-ENTITY-SENSOR-MIB constraints. For detailed definitions of MIB objects,
see the MIB.
Table 3-17
CISCO-ENTITY-SENSOR-MIB Constraints
MIB Object
Notes
entSensorThresholdTable
•
entSensorThresholdRelation
Read-only.
•
entSensorThresholdSeverity
Read-only.
•
entSensorThresholdValue
Read-only.
MIB Usage Values for Cisco Transceivers
The tables in this section lists each type of sensor’s value represented in the entSensorValueTable and
the entSensorThresholdTable.
Table 3-18 lists CISCO-ENTITY-SENSOR-MIB sensor objects and their usage values for Cisco 7600
transceivers in the entSensorValueTable.
Table 3-18
CISCO-ENTITY-SENSOR-MIB Usage Values in the entSensorValueTable for Cisco
Transceivers
MIB Sensor Object
Notes
Module Temperature Sensor
•
entSensorType
celsius(8)
•
entSensorScale
units(9)
•
entSensorPrecision
1
•
entSensorStatus
ok(1)
•
entSensorValue
Reports most recent measurement seen by the sensor.
•
entSensorValueTimeStamp
Value indicates the age of the value reported by
entSensorValue object.
•
entSensorValueUpdateRate
Value indicates the rate that the agent updates
entSensorValue (in seconds). For example, 60 seconds.
Module Voltage Sensor
•
entSensorType
volts(DC)4
•
entSensorScale
units(9)
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-75
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-SENSOR-MIB
Table 3-18
CISCO-ENTITY-SENSOR-MIB Usage Values in the entSensorValueTable for Cisco
Transceivers (continued)
MIB Sensor Object
Notes
•
entSensorPrecision
1
•
entSensorStatus
ok(1)
•
entSensorValue
Reports most recent measurement seen by the sensor.
•
entSensorValueTimeStamp
Value indicates the age of the value reported by
entSensorValue object.
•
entSensorValueUpdateRate
Value indicates the rate that the agent updates
entSensorValue in seconds.
Tx Laser Current Sensor
•
entSensorType
amperes(5)
•
entSensorScale
milli(8)
•
entSensorPrecision
1
•
entSensorStatus
ok(1)
•
entSensorValue
Reports most recent measurement seen by the sensor.
•
entSensorValueTimeStamp
Value indicates the age of the value reported by
entSensorValue object.
•
entSensorValueUpdateRate
Value indicates the rate that the agent updates
entSensorValue (in seconds). For example, 60 seconds.
Transmit Power Sensor (Optical Tx)
Receive Power Sensor (Optical Rx)
•
entSensorType
dBm(14)
•
entSensorScale
units(9)
•
entSensorPrecision
1
•
entSensorStatus
ok(1)
•
entSensorValue
Reports most recent measurement seen by the sensor.
•
entSensorValueTimeStamp
Value indicates the age of the value reported by
entSensorValue object.
•
entSensorValueUpdateRate
Value indicates the rate that the agent updates
entSensorValue (in seconds). For example, 60 seconds.
Each Cisco transceiver sensor has 4 threshold values corresponding to the four alarm states listed in
Table 3-19 and Table 3-20. The entSensorValueTable is indexed by both entPhysicalIndex and
entSensorThresholdIndex. Cisco 7600 entSensorThresholdIndices range from 1 to 4. For N/A (not
applicable), a value of zero is returned.
Table 3-19 lists the default values for the Cisco GBIC transceivers in the entSensorThresholdTable.
Cisco 7600 Series Router MIB Specifications Guide
3-76
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ENTITY-VENDORTYPE-OID-MIB
Table 3-19
Default Values in the entSensorThreshold Table for DWDM GBIC Transceivers
MIB Sensor Object
High Alarm
High Warning
Low Warning
Low Alarm
Temperature
70.0
60.0
5.0
0.0
Voltage
5.5
5.2
4.7
4.5
Tx Bias Current
60.0
40.0
10.0
5.0
Tx Optical Power
3.4
3.2
-0.3
-0.5
Rx Optical Power
5.9
-6.7
-28.5
-28.5
Table 3-20 lists the default values for the Cisco XENPAK transceivers in the entSensorThresholdTable.
Table 3-20
Default Values in the entSensorThreshold Table for XENPAK Transceivers
MIB Sensor Object
High Alarm
High Warning
Low Warning
Low Alarm
Temperature
70.0
60.0
5.00.0
0.0
Voltage
Not applicable.
Not applicable.
Not applicable. Not applicable.
Tx Bias Current
80.0
75.0
15.0
10.0
Tx Optical Power
2.0
0.9
-4.0
-9.7
Rx Optical Power
2.0
0.4
-11.9
-15.0
CISCO-ENTITY-VENDORTYPE-OID-MIB
The CISCO-ENTITY-VENDORTYPE-OID-MIB defines the object identifiers (OIDs) assigned to
various Cisco 7600 Series router components. The OIDs in this MIB are used by the entPhysicalTable
of the ENTITY-MIB as values for the entPhysicalVendorType field in the entPhysicalTable. Each OID
uniquely identifies a type of physical entity, such as a chassis, Optical Services Module, FlexWAN card,
SPAs, and SIPs.
CISCO-ENVMON-MIB
The CISCO-ENVMON-MIB contains information about the status of environmental sensors (for
voltage, temperature, and power supplies). It also contains MIB objects to enable and disable
notifications for changes to the status of these sensors.
Note
The CISCO-ENVMON-MIB is not supported by the shared port adapters (SPAs).
MIB Constraints
Table 3-21 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-ENVMON-MIB.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-77
Chapter 3
Cisco 7600 MIB Specifications
CISCO-ERM-MIB
F
Table 3-21
CISCO-ENVMON-MIB Constraints
MIB Object
Notes
ciscoEnvMonVoltageStatusTable
•
ciscoEnvMonVoltageStatusDescr
Not implemented.
•
ciscoEnvMonVoltageStatusValue
Not implemented.
•
ciscoEnvMonVoltageThresholdLow
Not implemented.
•
ciscoEnvMonVoltageThresholdHigh
Not implemented.
•
ciscoEnvMonVoltageLastShutdown
Not implemented.
•
ciscoEnvMonVoltageState
Not implemented.
•
ciscoEnvMonEnableVoltageNotification
Not implemented.
CISCO-ENVMON-MIB Usage
The command show environment can be used to check environmental status through the CLI. The
objects defined in ciscoEnvMonMIBNotificationEnables can be set to true using CLI command
snmp-server enable traps environment.
CISCO-ERM-MIB
The CISCO-ERM-MIB is for the Embedded Resource Manager (ERM framework which helps in
effectively managing resources such as cpu, memory, buffers, etc).
CISCO-ETHER-CFM-MIB
The CISCO-ETHER-CFM-MIB defines the managed objects and notifications for Ethernet Connectivity
Fault Management (CFM). CFM is an end-to-end per service instance Ethernet layer Operations,
Administration and Management (OAM) protocol.
CISCO-FLASH-MIB
The CISCO-FLASH-MIB contains objects to manage flash cards and flash-card operations.
CISCO-FLEX-LINKS-MIB
The CISCO-FLEX-LINKS-MIB is for configuration and status query of Flex Links feature on the Cisco
device.
Flex Links are a pair of a Layer 2 interfaces, where one interface is configured to act as a backup to the
other. The feature provides an alternative solution to the Spanning Tree Protocol (STP), allowing users
to turn off STP and still provide basic link redundancy.
Cisco 7600 Series Router MIB Specifications Guide
3-78
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-FRAME-RELAY-MIB
Flex Links are typically configured in service provider or enterprise networks where users do not want
to run STP on the device.
CISCO-FRAME-RELAY-MIB
The CISCO-FRAME-RELAY-MIB contains Frame Relay information that is specific to Cisco products
or that is missing from RFC 1315.
MIB Constraints
Table 3-22 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-FRAME-RELAY-MIB. Unless noted otherwise, the Cisco 7600 implementation of a MIB
follows the standard. Any objects not listed in a table are implemented as defined in the MIB.
Note
Frame relay SVCs are not currently supported in Cisco 7600.
Table 3-22
CISCO-FRAME-RELAY-MIB Constraints
MIB Object
Notes
cfrCircuitTable
•
cfrCircuitType
Supported value is pvc(1).
cfrExtCircuitTable
•
cfrExtCircuitMinThroughputOut
Supported for QoS. Otherwise value is 0.
•
cfrExtCircuitMinThroughputIn
Supported for QoS. Otherwise value is 0.
•
cfrExtCircuitShapeByteLimit
Supported for QoS. Otherwise value is 0.
•
cfrExtCircuithapeInterval
Supported for QoS. Otherwise value is 0.
•
cfrExtCircuitShapeByteIncrement
Supported for QoS. Otherwise value is 0.
•
cfrExtCircuitShapeActive
Supported for QoS. Otherwise value is 0.
•
cfrExtCircuitShapeAdapting
Supported for QoS. Otherwise value is 0.
cfrMapTable
•
cfrMapType
cfrSvcTable
Values are:
•
static(1)
•
dynamic(2)
Not implemented.
CISCO-FRAS-HOST-MIB
The CISCO-FRAS-HOST-MIB contains objects specific to upstream or host-end sessions.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-79
Chapter 3
Cisco 7600 MIB Specifications
CISCO-FTP-CLIENT-MIB
CISCO-FTP-CLIENT-MIB
The CISCO-FTP-CLIENT-MIB contains objects to invoke File Transfer Protocol (FTP) operations for
network management. This MIB has no known constraints and all objects are implemented as defined in
the MIB.
CISCO-HSRP-EXT-MIB
The CISCO-HSRP-EXT-MIB provides an extension to the CISCO-HSRP-MIB which defines the Cisco
Hot Standby Router Protocol (HSRP), which is defined in RFC 2281. The extensions cover assigning of
secondary IP addresses and modifying an HSRP group’s priority.
CISCO-HSRP-MIB
The CISCO-HSRP-MIB contains objects to configure and manage the Cisco Hot Standby Router
Protocol (HSRP), which is defined in RFC 2281.
CISCO-IETF-ATM2-PVCTRAP-MIB-EXTN
The CISCO-IETF-ATM2-PVCTRAP-MIB-EXTN MIB supplements the
CISCO-IETF-ATM2-PVCTRAP-MIB.
CISCO-IETF-ATM2-PVCTRAP-MIB
The CISCO-IETF-ATM2-PVCTRAP-MIB supplements the ATM-MIB. It implements the virtual
channel link (VCL) section of the IETF document “draft-ietf-atommib-atm2-11.txt,” Section 9 ATM
Related Trap Support.
CISCO-IETF-DHCP-SERVER-EXT-MIB
The CISCO-IETF-DHCP-SERVER-EXT-MIB is an extension of the
CISCO-IETF-DHCP-SERVER-MIB.
CISCO-IETF-DHCP-SERVER-MIB
The CISCO-IETF-DHCP-SERVER-MIB contains objects for the entities implementing the server side
of the Bootstrap Protocol (BOOTP) and the Dynamic Host Configuration protocol (DHCP) for Internet
Protocol version 4(IPv4). This MIB does not include support for updating Dynamic DNS (DDNS) and
DHCP Failover Protocol.
Cisco 7600 Series Router MIB Specifications Guide
3-80
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-IETF-FRR-MIB
CISCO-IETF-FRR-MIB
The CISCO-IETF-FRR-MIB contains managed object definitions for MPLS Fast Reroute (FRR).
CISCO-IETF-IP-MIB
The CISCO-IETF-IP-MIB contains objects to manage the Internet Protocol (IPv6), but not IP routes. The
MIB also contains objects to manage the Internet Control Message Protocol (ICMP). It is based on the
IETF document draft-ietf-ipngwg-rfc2011-update-00.txt and supports read-only.
Note
This MIB only supports IPv6 interfaces.
Table 3-23 lists constraints that the Cisco 7600 Series router places on objects in the
CISCO-IETF-IP-MIB.
Table 3-23
CISCO-IETF-IP-MIB Constraints
MIB Object
Notes
•
cIpv6Forwarding
Read-only.
•
cIpv6DefaultHopLimit
Read-only.
cIpv6InterfaceTable
•
cIpv6InterfaceIdentifier
Read-only.
•
cIpv6InterfaceIdentifierLength
Read-only.
cIpAddressPfxTable
•
cIpAddressPfxOrigin
Read-only.
Values:
•
other(1)
•
manual(2)
cIpAddressTable
•
cIpAddressOrigin
Read-only.
Values:
•
cIpAddressStatus
•
other(1)
•
manual(2)
•
wellknown(3)
Read-only. Value is depracated(2). No longer
supported
cInetNetToMediaTable
•
cInetNetToMediaPhysAddress
Read-only.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-81
Chapter 3
Cisco 7600 MIB Specifications
CISCO-IETF-ISIS-MIB
Table 3-23
CISCO-IETF-IP-MIB Constraints (continued)
MIB Object
•
cInetNetToMediaType
Notes
Read-only.
Values:
•
cInetNetToMediaState
•
other(1)
•
dynamic(3)
•
static(4)
Read-only. Value is invalid(5). Not supported.
cInetIcmpTable
•
cInetIcmpOutErrors
Not Implemented.
CISCO-IETF-ISIS-MIB
The CISCO-IETF-ISIS-MIB contains objects to manage IS-IS Routing protocol described in ISO 10589.
IS-IS Routing protocol is used to construct routing tables for IP networks, as described in RFC 1195.
CISCO-IETF-IP-FORWARD-MIB
The CISCO-IETF-IP-FORWARD-MIB contains objects to manage multipath IP (IPv6) routes in a
classless interdomain routing (CIDR) environment. This MIB is based on the IETF document
draft-ietf-ipngwg-rfc2096-update-00.txt and supports read-only.
CISCO-IETF-PPVPN-MPLS-VPN-MIB
The CISCO-IETF-PPVPN-MPLS-VPN-MIB is an extension of the MPLS-VPN-MIB. It contains a new
notification, mplsNumVrfRouteMaxThreshCleared, which was added with
MPLS-VPN-MIB-DRAFT-05.
CISCO-IETF-PW-ATM-MIB
The CISCO-IETF-PW-ATM-MIB contains managed object definitions for Pseudo Wire emulation of
ATM over Packet Switched Networks(PSN).
CISCO-IETF-PW-ENET-MIB
The CISCO-IETF-PW-ENET-MIB describes a model for managing Ethernet point-to-point pseudo wire
services over a Packet Switched Network (PSN).
Cisco 7600 Series Router MIB Specifications Guide
3-82
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-IETF-PW-FR-MIB
CISCO-IETF-PW-FR-MIB
The CISCO-IETF-PW-FR-MIB describes network management objects defined for FRoPW services
over a Packet Switched Network (PSN).
CISCO-IETF-PW-MIB
The CISCO-IETF-PW-MIB contains managed object definitions for Pseudo Wire operation.
CISCO-IETF-PW-MPLS-MIB
The CISCO-IETF-PW-MPLS-MIB complements the CISCO-IETF-PW-MIB for PW operation over
MPLS.
CISCO-IETF-PW-TC-MIB
The CISCO-IETF-PW-TC-MIB provides Textual Conventions and OBJECT-IDENTITY Objects to be
used PW services.
CISCO-IETF-PW-TDM-MIB
The CISCO-IETF-PW-TDM-MIB contains managed object definitions for encapsulating TDM (T1,E1,
T3, E3, NxDS0) as pseudo-wires over packet-switching networks (PSN)
CISCO-IF-EXTENSION-MIB
The CISCO-IF-EXTENSION-MIB contains objects that provide additional interface-related
information that is not available in the IF-MIB (RFC 2863).
Table 3-24 lists constraints for Cisco 7600 WAN interfaces.
Table 3-24
CISCO-IF-EXTENSION-MIB Constraints
MIB Object
Notes
cielInterfaceTable
•
cieIfDhcpMode
Not implemented.
•
cieIfMtu
Not implemented.
•
cieIfContextName
Not implemented.
•
cieIfKeepAliveEnabled
Not supported for ATM interfaces.
cieSystemMtu
Not implemented.
cieIfUtilTable
Not implemented.
cieIfDot1dBaseMappingTable
Not implemented.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-83
Chapter 3
Cisco 7600 MIB Specifications
CISCO-IMAGE-MIB
Table 3-24
CISCO-IF-EXTENSION-MIB Constraints (continued)
MIB Object
Notes
cieIfDot1qCustomerEtherTypeTable
Not implemented.
cieIfNameMappingTable
Not implemented.
1 Some objects defined in cieIfPacketStatsTable and cieIfInterfaceTable are applicable to physical interfaces
only. As a result, this table may be sparse for non-physical interfaces.
2 ATM interfaces do not support the cieIfKeepAliveEnabled object.
CISCO-IMAGE-MIB
The CISCO-IMAGE-MIB contains objects which identify the capabilities and characteristics of the
Cisco IOS image.
CISCO-IMAGE-TC-MIB
The CISCO-IMAGE-TC-MIB defines the textual conventions used in the enhanced image MIB.''
CISCO-IP-STAT-MIB
The CISCO-IP-STAT-MIB contains objects to manage the collection and display of IP statistics,
categorized by IP precedence and the Media Access Control (MAC) address associated with IP packets.
To use the MIB to access additional IP statistics, you can issue the ip accounting mac-address and
ip accounting precedence commands at the CLI.CISCO-IPMROUTE-MIB
The CISCO-IPMROUTE-MIB contains objects to manage IP multicast routing on the router.
CISCO-IPSEC-FLOW-MONITOR-MIB
The CISCO-IPSEC-FLOW-MONITOR-MIB allows monitoring of the structures in IPSec-based Virtual
Private Networks.
CISCO-IP-TAP-MIB
The CISCO-IP-TAP-MIB manages Cisco's intercept feature for IP. This MIB is used along with
CISCO-TAP2-MIB to intercept IP traffic.
CISCO-IP-URPF-MIB
The CISCO-IP-URPF-MIB contains objects to manage Unicast Reverse Path Forwarding (URPF).
URPF validates the source address of IP packets received on an interface to prevent Denial of Service
attacks based on IP address spoofing.
Cisco 7600 Series Router MIB Specifications Guide
3-84
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-IPSEC-MIB
CISCO-IPSEC-MIB
The CISCO-IPSEC-MIB models the Cisco implementation-specific attributes of a Cisco entity that
implements IPsec.
CISCO-IPSLA-ETHERNET-MIB
The CISCO-IPSLA-ETHERNET-MIB contains objects to manage IP SLA Auto-Ethernet-CFM
operations and EthernetJitter statistics. IP SLA is a capability which utilizes active monitoring for
network performance. It can be used for network troubleshooting, network assessment, and health
monitoring. EthernetJitter is used to measure metrics such as RTT, Jitter, frame loss, and one-way
latency by sending multiple enhanced CFM frames at specified interval to a particular MEP.
CISCO-L2-CONTROL-MIB
The CISCO-L2-CONTROL-MIB contains objects that provide a n control feature for devices with
Layer 2 functions such as the VLAN MAC limit control. The MIB controls the number of MAC address
entries for each VLAN so that the forwarding table is not depleted.
CISCO-L2-TUNNEL-CONFIG-MIB
The CISCO-L2-TUNNEL-CONFIG-MIB contains objects to configure and manage Layer 2 tunnels on
the router. Tunneling allows separate local networks to appear as a single virtual LAN (VLAN). The
networks are connected through an ISP, which tunnels the packets from one network to another, making
it appear as if both networks are a single network.
CISCO-L2L3-INTERFACE-CONFIG-MIB
The CISCO-L2L3-INTERFACE-CONFIG-MIB contains objects to configure the operation mode of
router interfaces and to monitor their status. You can configure a router interface to operate in routed(1)
or switchport(2) mode:
•
Routed(1) mode—Layer 3 protocols are used to direct traffic across the interface.
•
Switchport(2) mode—Layer 2 protocols are used to direct traffic across the interface. This mode can
be configured manually, or negotiated by the dynamic trunking protocol (DTP) or the dynamic
interswitch link (DISL) protocol. The interface can be configured to operate in access mode, trunk
mode, or multimode.
CISCO-LAG-MIB
The CISCO-LAG-MIB contains objects to manage link aggregation (LAG) on the router, as defined by
IEEE Standard 802.3ad. The MIB contains link aggregation information that is not included in the
IEEE8023-LAG-MIB or that is specific to Cisco products.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-85
Chapter 3
Cisco 7600 MIB Specifications
CISCO-MAC-NOTIFICATION-MIB
CISCO-MAC-NOTIFICATION-MIB
The CISCO-MAC-NOTIFICATION-MIB is for configuration of the MAC notification feature. MAC
notification is a mechanism to inform monitoring devices when there are MAC addresses learnt or
removed from the forwarding database of the monitored devices.
CISCO-MEMORY-POOL-MIB
The CISCO-MEMORY-POOL-MIB contains objects that represents the different types of memory pools
that may be present in a managed device. Memory pools are categorized into two groups:
•
Predefined pools
•
Dynamic pools
CISCO-MVPN-MIB
The CISCO-MVPN-MIB contains managed object definitions for Cisco implementation of multicast in
VPNs defined by the Internet draft: draft-rosen-vpn-mcast-05.txt.
CISCO-NAC-NAD-MIB
The CISCO-NAC-NAD-MIB is for the configuration of a Network Access Device (NAD) on the Cisco
Network Admission Control (NAC) system.
CISCO-NDE-MIB
The CISCO-NDE-MIB contains objects to configure and monitor the operation of the NetFlow Data
Export (NDE) feature. A network flow is a unidirectional sequence of packets between a pair of source
and destination endpoints, which are identified by IP address and transport layer application port
number. NetFlow uses the IP protocol type, type of service (ToS), and input interface identifier to
uniquely identify network flows.
CISCO-NETFLOW-MIB
The CISCO-NETFLOW-MIB provides a simple and easy method to get NetFlow cache information,
current NetFlow configuration and statistics.
Cisco 7600 Series Router MIB Specifications Guide
3-86
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-NTP-MIB
CISCO-NTP-MIB
The CISCO-NTP-MIB contains objects to monitor a Network Time Protocol (NTP) server. NTP is used
to synchronize timekeeping among a set of distributed time servers and clients. Primary time servers,
which are synchronized to national time standards, are connected to widely accessible resources such as
backbone gateways. These primary servers send timekeeping information to other time servers, and
perform clock checking to eliminate timekeeping errors due to equipment or propagation failures.
CISCO-OSPF-MIB
The CISCO-OSPF-MIB contains objects for managing OSPF implementation. Most of the MIB
definitions are based on the IETF draft < draft-ietf-ospf-mib-update-05.txt > and includes support for
OSPF Sham link. The CISCO-OSPF-MIB is an extension to the OSPF-MIB defined in RFC 1850.
CISCO-OSPF-TRAP-MIB
The CISCO-OSPF-TRAP-MIB contains new and modified notification objects and events, which are
defined in the latest version for OSPF MIB IETF draft draftietf-ospf-mib-update-05.txt in addition to
support for OSPF Sham link.
CISCO-PAE-MIB
The CISCO-PAE-MIB contains objects to manage port access entities (PAEs) on the router, as defined
by IEEE Std 802.1x. The MIB contains PAE information that is not included in the IEEE8021-PAE-MIB
or that is specific to Cisco products.
CISCO-PAGP-MIB
The CISCO-PAGP-MIB contains objects to configure and manage Fast Etherchannel and the Port
Aggregation Protocol (PAgP) on the router. These features allow two or more physical interfaces to be
aggregated together to form a single agport that behaves like a single interface, but that has improved
bandwidth and availability over each of the physical interfaces.
Note
You can also monitor interfaces, agports, and related statistics through the ifStackTable and the ifTable
(IF-MIB).
CISCO-PIM-MIB
The CISCO-PIM-MIB defines Cisco specific objects and variables for managing Protocol Independent
Multicast (PIM) on the router. These MIB definitions are an extension of those in RFC 2934, which is
the IETF PIM MIB.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-87
Chapter 3
Cisco 7600 MIB Specifications
CISCO-PING-MIB
CISCO-PING-MIB
The CISCO-PING-MIB contains objects to manage ping requests on the router.
CISCO-POLICY-GROUP-MIB
The CISCO-POLICY-GROUP-MIB is used for configuration of policy and policy group. A policy group
can be described as a set of entities identified by IP addresses or other means. Members of a policy group
will be subjected to the same policy.
CISCO-PORT-SECURITY-MIB
The CISCO-PORT-SECURITY-MIB is used for managing Cisco Port Security
CISCO-PPPOE-MIB
The CISCO-PRIVATE-VLAN-MIB contains objects to manage Cisco PPPoE sessions.
CISCO-PRIVATE-VLAN-MIB
The CISCO-PRIVATE-VLAN-MIB contains objects to manage the private virtual LAN (VLAN) feature
on the router.
CISCO-PROCESS-MIB
The CISCO-PROCESS-MIB displays memory and CPU usage on the router and describes active system
processes. CPU utilization presents a status of how busy the system is. The numbers are a ratio of the
current idle time over the longest idle time (this information should be used as an estimate only).
MIB Constraints
Table 3-25 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-PROCESS-MIB.
Table 3-25
CISCO-PROCESS-MIB Constraints
MIB Object
Notes
cpmProcessTable
•
cpmProcExtPriority
Read-only.
Cisco 7600 Series Router MIB Specifications Guide
3-88
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-PRODUCTS-MIB
CISCO-PROCESS-MIB Usage
The CISCO-PROCESS-MIB supports the 7600 WAN Cards (FlexWANs, OSM, SIPs) cards. These cards
have one or two CPUs. The CISCO-PROCESS-MIB contains information for each CPU present.
The cpmCPUTotal5sec, cpmCPUTotal1min, and cpmCPUTotal5min objects have been deprecated and
replaced by cpmCPUTotal5secRev, cpmCPUTotal1minRev, and cpmCPUTotal5minRev respectively.
Note
When an object is deprecated it does not mean that an object instance may not be returned. For these
deprecated objects, object instances are returned. However, their returned values must be ignored. The
values returned by the new objects must be used.
CISCO-PRODUCTS-MIB
The CISCO-PRODUCTS-MIB lists the object identifiers (OIDs) assigned to Cisco hardware platforms.
The following OIDs are supported:
•
cisco7603 (1.3.6.1.4.1.9.1.401)
•
cisco7606 (1.3.6.1.4.1.9.1.402)
•
cisco7609 (1.3.6.1.4.1.9.1.509)
•
cisco7613 (1.3.6.1.4.1.9.1.528)
•
cisco7604 (1.3.6.1.4.1.9.1.658)
•
cisco7609s (1.3.6.1.4.1.9.1.835)
•
cisco7603s (1.3.6.1.4.1.9.1.862)
•
cisco7606s (1.3.6.1.4.1.9.1.863)
This MIB is included in the Cisco 7600 executable image, but its support is unverified.
CISCO-QINQ-VLAN-MIB
The CISCO-QINQ-VLAN-MIB describes configuration and monitoring capabilities relating to
802.1QinQ interfaces.
MIB Constraints
Table 3-26 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-QINQ-VLAN-MIB.
Table 3-26
CISCO-QINQ-VLAN-MIB Constraints
MIB Object
Notes
cqvTerminationTable
Not implemented. Cisco7600 does not
support QinQ Termination feature.
cqvTranslationTable
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-89
Chapter 3
Cisco 7600 MIB Specifications
CISCO-QLLC01-MIB
Table 3-26
CISCO-QINQ-VLAN-MIB Constraints (continued)
MIB Object
Notes
•
cqvTranslationTrunkPeVlanId
Read-only.
•
cqvTranslationTrunkCeVlanId
Read-only.
•
cqvTranslationType
Read-only.
•
cqvTranslationCosPBits
Read-only.
•
cqvTranslationRowStatus
Read-only.
CISCO-QLLC01-MIB
The CISCO-QLLC01-MIB contains objects to configure and monitor logical connections for the
Qualified Logical Link Control (QLLC) protocol.
CISCO-QUEUE-MIB
The CISCO-QUEUE-MIB contains objects to manage interface queues, which can be used for FIFO,
priority, custom, and fair queuing.
CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
The CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB defines objects required for managing
Resilient Ethernet Protocol (REP). Resilient Ethernet Protocol (REP) is a Cisco proprietary protocol that
provides an alternative to Spanning Tree Protocol (STP). REP provides functionality to control network
loops, handle link failures, and improve convergence time.
CISCO-RF-MIB
The CISCO-RF-MIB provides configuration control and status for the Redundancy Framework (RF)
subsystem. RF provides a mechanism for logical redundancy of software functionality and is designed
to support 1:1 redundancy on processor cards (supervisor engines). Redundancy duplicates data
elements and software functions to provide an alternative in case of failure.
Note
For information about the levels of redundancy and how to verify that the redundancy feature is available
on Cisco 7600 routers, see Appendix A, “Cisco Redundancy Features.”
MIB Constraints
Table 3-27 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-RF-MIB.
Cisco 7600 Series Router MIB Specifications Guide
3-90
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-RMON-CONFIG-MIB
Table 3-27
CISCO-RF-MIB Constraints
MIB Object
Notes
cRFCfgGroup
•
cRFCfgSplitMode
Object is deprecated.
•
cRFCfgRedundancyMode
Values: 6, 7, and 8.
•
cRFCfgMaintenanceMode
Read-only. Supported value is false(2).
cRFHistoryGroup
•
cRFHistory
There are three switchover modes:
coldstandby, warmstandby, and hoststandby.
The only entries saved are those generated
from a hotstandby switchover.
CISCO-RMON-CONFIG-MIB
The CISCO-RMON-CONFIG-MIB contains Cisco RMON configuration span extensions for the
standard IETF remote monitoring (RMON) MIBs.
CISCO-RSRB-MIB
The CISCO-RSRB-MIB contains objects used to manage remote source-route bridging (RSRB) on the
router. This MIB provides information about the attributes of the local-remote RSRB peer relationship.
CISCO-RTTMON-MIB
The CISCO-RTTMON-MIB contains objects to monitor network performance. The MIB provides
information about the response times of network resources and applications. Each conceptual round-trip
time (RTT) control row in the MIB represents a single probe, which is used to determine an entity’s
response time. The probe defines an RTT operation to perform (for example, an FTP or HTTP get
request), and the results indicate whether the operation succeeded or failed, and how long it took to
complete.
If you plan to schedule an RTT operation, see Table 3-28 for information about
rttMonScheduleAdminRttStartTime in the rttMonScheduleAdminTable.
Note
An rttMonCtrlOperConnectionLostOccurred trap is generated when an RTT connection cannot be
established to the destination router because the router responder application is not running. However,
the trap is not generated if the physical connection to the router is lost.
MIB Constraints
Table 3-28 lists the constraints that the Cisco 7600 Series router places on objects in the
CISCO-RTTMON-MIB. For detailed definitions of MIB objects, see the MIB.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-91
Chapter 3
Cisco 7600 MIB Specifications
CISCO-RTTMON-IP-EXT-MIB
Table 3-28
CISCO-RTTMON-MIB Constraints
MIB Object
Notes
RttMonProtocol
Not supported:
snaRUEcho
snaLU0EchoAppl
rttMonApplAuthTable
Not supported.
rttMonCtrlAdminTable
•
rttMonCtrlAdminRttType
Supported values:
echo(1)
pathEcho(2)
udpEcho(5)
tcpConnect(6)
http(7)
dns(8)
jitter(9)
ftp(12)
All other values not supported.
rttMonEchoAdminTable
•
rttMonEchoAdminProtocol
Supported values:
ipIcmpEcho(2)
ipUdpEchoAppl(3)
ipTcpConn(24)
httpAppl(25)
dnsAppl(26)
jitterAppl(27)
ftpAppl(30)
All other values not supported.
rttMonScheduleAdminTable
•
rttMonScheduleAdminRttStartTime
rttMonHistoryCollectionTable
Before setting this object to a date/time value,
make sure the ESR clock was set through the
CLI clock set command. Otherwise, the
scheduled RTT operation does not run.
HTTP and Jitter types not supported.
CISCO-RTTMON-IP-EXT-MIB
The CISCO-RTTMON-IP-EXT-MIB contains extensions to tables in CISCO-RTTMON-MIB to support
IP-layer extensions including IPv6 addresses, information related to IPv6, and additional IP information.
Cisco 7600 Series Router MIB Specifications Guide
3-92
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-SDLLC-MIB
CISCO-SDLLC-MIB
The CISCO-SDLLC-MIB contains object to manage SDLC Logical Link Control (SDLLC). The MIB
contains read-only configuration and operational information for Cisco implementation of Synchronous
Data Link Control (SDLC) to Logical Link Control, type 2 (LLC2) media translation.
CISCO-SLB-EXT-MIB
The CISCO-SLB-EXT-MIB contains extensions to the Cisco server load-balancing MIB
(CISCO-SLB-MIB). Server load balancing enables the router to balance the processing of packets and
connections from a number of other devices, such as real servers, firewalls, or caches. An SLB device
determines how to handle incoming frames and connections according to the contents of the incoming
data and various configuration options.
CISCO-SLB-MIB
The CISCO-SLB-MIB contains objects to manage server load-balancing (SLB) managers, such as those
provided by the Cisco IOS SLB product. The MIB includes objects for the manager-side implementation
of the Dynamic Feedback Protocol (DFP), which is used to obtain information about servers.
CISCO-SMI-MIB
The CISCO-SMI-MIB defines the structure of management information for Cisco enterprise MIBs.
CISCO-SNADLC-CONV01-MIB
The CISCO-SNADLC-CONV01-MIB contains objects that manage QLLC-to-SDLC and
QLLC-to-LLC2 conversion.
CISCO-SNAPSHOT-MIB
The CISCO-SNAPSHOT-MIB contains objects to manage snapshot routing, which helps improve the
use of system resources for static routing and routing for dedicated serial lines.
CISCO-SNMP-TARGET-EXT-MIB
The CISCO-SNMP-TARGET-EXT-MIB is an extension of the SNMP-TARGET-MIB specified in
RFC2273
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-93
Chapter 3
Cisco 7600 MIB Specifications
CISCO-SONET-MIB
CISCO-SONET-MIB
The CISCO-SONET-MIB contains objects to describe SONET/SDH interfaces on the router. This MIB
is an extension to the standard SONET-MIB (RFC 2558). The CISCO-SONET-MIB has objects that
provide additional SONET related information not found in the SONET-MIB. For detailed definitions
of MIB objects, see the MIB.
MIB Constraints
The following CISCO-SONET-MIB tables are not implemented in the Cisco 7600 platform:
Note
•
csConfigTable
•
csVTConfigTable
•
csAPSConfigTable
•
cssTranceTable
•
cspTranceTable
•
csStatsTable
•
cspConfigTable
Only the section, line, and path totals objects from the ciscoSonetStatsMIBGroup and the complete
ciscoSonetEnableGroup must be supported. All network elements containing one or more SONET
interfaces must implement this MIB.
CISCO-SRP-MIB
The CISCO-SRP-MIB contains objects that describe the spatial reuse protocol (SRP) interface layer.
CISCO-STACK-MIB
The CISCO-STACK-MIB provides configuration information and runtime status for router components.
On the Cisco 7600 Series router, the CISCO-STACK-MIB contains information about the chassis, ports,
and modules.
Note
Before the ENTITY-MIB standardization, the OLD-CHASSIS-MIB and CISCO-STACK-MIB were
used to support physical entities. The CISCO-STACK-MIB is supported on the Cisco 7600 Series router
for LAN cards, OSM cards, and FlexWAN/SPAs. PAs, SIPs and SPAs and are not supported.
Table 3-29 lists the values that the Cisco 7600 Series router uses for module types.
Cisco 7600 Series Router MIB Specifications Guide
3-94
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-STP-EXTENSIONS-MIB
Table 3-29
CISCO-STACK-MIB Module Type Values for the Cisco 7600 Series Router
MIB Object
Notes
moduleTable
•
moduleType
Module Type
Part Number
Enhanced OC-48/STM-16 POS/SDH OSM WAN ports
osm1oc48PosSSPlus(611)
OSM-1OC-48-POS-SS+
osm1oc48PosSIPlus(612)
OSM-1OC-48-POS-SI+
osm1oc48PosSLPlus(613)
OSM-1OC-48-POS-SL+
Enhanced OC-12/STM-4 POS/SDH OSM WAN ports
osm2oc12PosMMPlus(608)
OSM-2OC-12-POS-MM+
osm4oc12PosSIPlus(617)
OSM-4OC-12-POS-SI+
Enhanced OC-12/ATM OSM WAN ports
osm2oc12AtmMMPlus(606)
OSM-2OC-12-ATM-MM+
osm2oc12AtmSIPlus(607)
OSM-2OC-12-ATM-SI+
Enhanced OC-3/STM-1 POS/SDH OSM WAN ports
osm16oc3PosSIPlus(610)
OSM-16OC-3-POS-SI+
osm4oc3PosSIPlus(614)
OSM-4OC-3-POS-SI+
osm8oc3PosSLPlus(615)
OSM-8OC-3-POS-SL+
osm8oc3PosSIPlus(616)
OSM-8OC-3-POS-SI+
Channelized DS3, GigE, and FlexWAN Modules
wsx6182pa(212)
WS-X6182-2PA
osm12ct3DS0(600)
OSM-12CT3/T1
osm24ct3DS0(287)
OSM-24CT3/T1
osm4GeWanGbicPlus(603)
OSM-2+4GE-WAN+
CISCO-STP-EXTENSIONS-MIB
The CISCO-STP-EXTENSIONS-MIB contains objects to manage Cisco extensions to the
Spanning-Tree Protocol (STP), which is defined by IEEE Std 802.1D.
CISCO-STUN-MIB
The CISCO-STUN-MIB contains objects to configure and monitor serial tunneling (STUN) on the
router. The MIB contains global STUN configuration and operational information, and objects to
manage STUN groups, ports, and routes.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-95
Chapter 3
Cisco 7600 MIB Specifications
CISCO-SVI-AUTOSTATE-MIB
CISCO-SVI-AUTOSTATE-MIB
The CISCO-SVI-AUTOSTATE-MIB is used for configuration of the switch virtual interface (SVI)
autostate feature. Autostate feature is a mechanism to calculate the state of a SVI dynamically when
some condition occurs such as a failure of a participating interface in that SVI.
CISCO-SWITCH-ENGINE-MIB
The CISCO-SWITCH-ENGINE-MIB contains objects to manage Cisco Layer 2 and 3 switches, such as
the Cisco 7600 Series router. Layer 2 and 3 switches can have a single (central) switching engine or
multiple (distributed) switching engines that are interconnected through a common switching fabric.
•
In a central-switching engine model, all physical ports in the system are handled by the single
switching engine.
•
In a distributed-switching model, each switching engine handles a set of local physical ports and
when necessary, uses the switching fabric to switch packets to other switching engines.
CISCO-SWITCH-QOS-MIB
The CISCO-SWITCH-QOS-MIB extends the CISCO-CLASS-BASED-QOS-MIB by defining
configuration and statistics information specific to the quality of service (QoS) features of Layer2/3
switch functionality implemented in Cisco devices. This MIB is applicable to a device which is fully
within a single QoS domain; one or more boundaries with other QoS domains can be immediately
adjacent to this device.
CISCO-SYSLOG-MIB
The CISCO-SYSLOG-MIB contains all system log messages generated by the Cisco IOS software. The
MIB provides a way to access these syslog messages through SNMP. All Cisco IOS syslog messages
contain the message name and its severity, message text, the name of the entity generating the message,
and an optional time stamp. The MIB also contains a history of syslog messages and counts related to
syslog messages.
Note
You can configure the Cisco 7600 Series router to send syslog messages to a ‘syslog’ server.
Note
The MIB does not keep track of messages generated from debug commands entered through the
command line interface (CLI).
Cisco 7600 Series Router MIB Specifications Guide
3-96
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-TAP2-MIB
CISCO-TAP2-MIB
The CISCO-TAP2-MIB manages Cisco's intercept feature. This MIB replaces CISCO-TAP-MIB. This
MIB defines a generic stream table that contains fields common to all intercept types. Specific intercept
filters are defined in extension MIBs. The MIBs are CISCO-IP-TAP-MIB for IP intercepts,
CISCO-802-TAP-MIB for IEEE 802 intercepts and CISCO-USER-CONNECTION-TAP-MIB for
RADIUS-based user connection intercepts.
CISCO-TC
The CISCO-TC contains objects that define textual conventions used throughout Cisco enterprise MIBs.
CISCO-TCP-MIB
The CISCO-TCP-MIB contains objects to manage the Transmission Control Protocol (TCP) on the
router. This MIB is an extension to the IETF TCP MIB.
CISCO-UDLDP-MIB
The CISCO-UDLDP-MIB contains objects to configure and manage the Cisco Uni Direction Link
Detection Protocol (UDLDP) on the router.
CISCO-VINES-MIB
The CISCO-VINES-MIB provides Virtual Integrated Network Service (VINES) routing information.
The MIB also contains objects from the Cisco VINES command line interface.
CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
The CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB contains VLAN-ID and ifIndex information for
each routed virtual LAN (VLAN) interface on the router. A routed VLAN interface is the router interface
or subinterface to which you attach the IP address used by the router on the VLAN. The MIB maps each
VLAN-ID to an ifIndex, which you can use to access the ipRouteTable to obtain the routing
configuration for the routed VLAN interface.
CISCO-VLAN-MEMBERSHIP-MIB
The CISCO-VLAN-MEMBERSHIP-MIB module provides management functions for the VLAN
Membership within the frame work of Cisco VLAN Architecture, Version 2.0. The MIB provides
information on VLAN Membership Policy Servers used by a device and VLAN membership
assignments of non-trunk bridge ports of the device.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-97
Chapter 3
Cisco 7600 MIB Specifications
CISCO-VLAN-TRANSLATION-MIB
CISCO-VLAN-TRANSLATION-MIB
The CISCO-VLAN-TRANSLATION-MIB provides management of VLAN translations. VLAN
translation refers to the ability of the device to translate between different virtual LANs or between
VLAN and non-VLAN encapsulating interfaces at Layer 2. Translation is typically used for selective
inter-VLAN switching of non-routable protocols and to extend a single VLAN topology across hybrid
switching environments
CISCO-VOICE-ANALOG-IF-MIB
The CISCO-VOICE-ANALOG-IF-MIB manages the E&M, FXO, FXS interfaces in the router. The
analog voice interface MIB provides the standard configuration, timing parameters, telephony hook, and
ring status information on Cisco Analog Voice interface implementation. The following groups are
managed:
Analog interface general group
•
E&M (recEive and transMit) interface group
•
FXO (Foreign Exchange Office) interface group
•
FXS (Foreign Exchange Station) interface group
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB
The CISCO-VOICE-COMMON-DIAL-CONTROL-MIB module contains voice related objects that are
common across more than one network encapsulation such as VoIP, VoATM, and VoFR.
CISCO-VOICE-DIAL-CONTROL-MIB
The CISCO-VOICE-DIAL-CONTROL-MIB module enhances the IETF Dial Control MIB (RFC 2128)
by providing management of voice telephony peers on both a circuit-switched telephony network, and
an IP data network.
CISCO-VOICE-IF-MIB
The CISCO-VOICE-IF-MIB module manages the common voice related parameters for both voice
analog and ISDN interfaces.
CISCO-VPDN-MGMT-EXT-MIB
The CISCO-VPDN-MGMT-EXT-MIB is a supplement to CISCO-VPDN-MGMT-MIB.
Cisco 7600 Series Router MIB Specifications Guide
3-98
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
CISCO-VPDN-MGMT-MIB
CISCO-VPDN-MGMT-MIB
The CISCO-VPDN-MGMT-MIB contains objects to manage the Virtual Private Dialup Network
(VPDN) feature of Cisco IOS. VPDN handles the forwarding of PPP links from an Internet Provider
(ISP) to a Home Gateway.
CISCO-VTP-MIB
The CISCO-VTP-MIB contains objects to configure and manage the VLAN Trunking Protocol (VTP)
and virtual LANs (VLANs) on the router.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-99
Chapter 3
Cisco 7600 MIB Specifications
DIAL-CONTROL-MIB
DIAL-CONTROL-MIB
The DIAL-CONTROL-MIB contains objects that describe peer information for demand access and
possibly other kinds of interfaces. Managing access circuits requires the following groups of
information:
•
General configuration information.
•
Information to describe peer configuration and peer statistics. In this respect, peer configuration
means information on how to connect to peers on outgoing calls, how to identify peers on incoming
calls, and other call related configuration information.
•
Information to store active call information.
•
Information to retain call history.
DIFFSERV-DSCP-TC
DIFFSERV-DSCP-TC contains the definitions of the textual conventions that should be used whenever
a Differentiated Services Code Point is used in a MIB.
DIFFSERV-MIB
The DIFFSERV-MIB defines the objects necessary to manage a device that uses the Differentiated
Services Architecture described in RFC 2475.
DS1-MIB (RFC 1406, 2495, 2495)
The DS1-MIB module contains a description of DS1, E1, DS2, and E2 interfaces objects.
Note
NOTE - Release 12.2(18)SXF and earlier support RFC1406. Release 12.2(33)SRA and later support
RFC 2495DS3-MIB
MIB Constraints
Table 3-30 describes constraints on objects from DS1-MIB definition. For detailed definitions of MIB
objects, see the MIB.
Table 3-30
DS1-MIB Constraints
MIB Object
Notes
dsx1ConfigTable
•
dsx1LineStatusChangeTrapEnable Read-only.
•
dsx1Channelization
Read-only.
•
dsx1LineLength
Read-only.
Cisco 7600 Series Router MIB Specifications Guide
3-100
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
DS3-MIB (RFC 1407)
Table 3-30
DS1-MIB Constraints (continued)
MIB Object
Notes
•
dsx1LineType
Read-only.
•
dsx1LineCoding
Read-only.
•
dsx1SendCode
Read-only.
•
dsx1CircuitIdentifier
Read-only.
•
dsx1LoopbackConfig
Read-only.
•
dsx1SignalMode
•
Read-only.
•
SPA-8XCHT1/E1 usage is always none(1).
•
dsx1TransmitClockSource
Read-only.
•
dsx1Fdl
Read-only.
•
dsx1LoopbackStatus
SPA-8XCHT1/E1 usage: Pay load loopbacks are
not supported (dsx1NearEndPayloadLoopback,
dsx1FarEndPayloadLoopback)
dsx1FracTable
Not implemented.
DS3-MIB (RFC 1407)
The DS3-MIB contains a description of DS3 and E3 interfaces objects.
MIB Constraints
Table 3-31 lists the constraints that the Cisco 7600 Series router places on objects in theRFC1407-MIB. For
detailed definitions of MIB objects, see the MIB. Any other object not listed in the table is implemented as
defined in the RFC 1407-MIB.
Table 3-31
DS3-MIB Constraints
MIB Object
Notes
dsx3ConfigTable
•
•
dsx3LineType
dsx3LineCoding
Supported values are:
•
T3 supports dsx3M23(2) and dsx3CbitParity(4)
•
E3 supports e3Framed(7) and e3Plcp(8)
Read-only. Supported values are:
•
T3 supports dsx3B3ZS(2)
•
E3 supports e3HDB3(3)
•
dsx3SendCode
Read-only. Supports only dsx3SendNoCode
•
dsx3TransmitClockSource Supported values are loopTiming(1) and
localTiming(2).
•
dsx3CircuitIdentifier
Read-only.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-101
Chapter 3
Cisco 7600 MIB Specifications
DLSW-MIB
Table 3-31
DS3-MIB Constraints (continued)
MIB Object
•
dsx3LoopbackConfig
Notes
Read-only.
dsx3FarEndConfigTable
Not implemented.
dsx3FarEndCurrentTable
Not implemented.
dsx3FarEndIntervalTable
Not implemented.
dsx3FarEndTotalTable
Not implemented.
dsx3FracTable
Not implemented.
* All T3/ATM line cards only support read-only values on all variables.
* The RFC1407-MIB usage supports the Cisco 7600 PA-MC-T3, PA-MC-E3, PA-A3-T3, PA-A3-E3 port
adapters.
* Currently for the dsx3FracTable to operate, the DS1 layer must be implemented in the ifTable. In this
release, this table is shown as not implemented because no rows are instantiated.
DLSW-MIB
The DLSW-MIB (RFC 2024)contains objects to manage data-link switching (DLSW) on the router.
ENTITY-MIB (RFC 2737)
The ENTITY-MIB allows functional component discovery. It is used to represent physical and logical
entities (components) in the router and manages those entities. The current software release supports the
RFC 2737 version of this MIB. This MIB is applicable to all OSM WAN ports, FlexWAN cards, port
adapters, and Cisco DWDM GBIC and XENPAK transceivers.
The following are the conformance groups contained in the ENTITY-MIB:
•
entityPhysical group—Describes the physical entities managed by a single agent.
•
entityLogical group—Describes the logical entities managed by a single agent.
•
entityMapping group—Describes the associations between the physical entities, logical entities,
interfaces, and non-interface ports managed by a single agent.
•
entityGeneral group—Describes general system attributes shared by potentially all types of entities
managed by a single agent.
•
entityNotifications group—Contains status indication notifications.
The following groups are added from RFC 2737:
•
entityPhysical2 group—This group augments the entityPhysical group.
•
entityLogical2 group—Describes the logical entities managed by a single agent, and replaces
entityLogical group.
The MIB table entPhysicalTable identifies the physical entities in the router. The entPhysicalTable
contains a single row for the Cisco 7600 chassis and a row for each entity in the chassis. A physical entity
may contain other entities. For example, a SIP-200 in slot 6 with one 4xOC3 POS SPA in subslot 6/0,
supports the following entities in this table: SPA and SIP modules, sensors on the SIP, and SPA ports.
For detailed definitions of MIB objects, see the MIB.
Cisco 7600 Series Router MIB Specifications Guide
3-102
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
ENTITY-SENSOR-MIB
ENTITY-SENSOR-MIB
The ENTITY-SENSOR-MIB contain objects that manage physical sensors, which are represented in the
Entity MIB with entPhysicalEntry and an entPhysicalClass value of sensor(8). The
ENTITY-SENSOR-MIB contains a single table, called the entPhySensorTable.
ETHERLIKE-MIB (RFC 2665, 3635)
The ETHERLIKE-MIB (RFC 2665) contains objects to manage Ethernet-like interfaces. Release
12.2(18)SXF and 12.2(33)SRA support the RFC 2665 version of the MIB. Release 12.2(33)SRC
supports the RFC 3635 version of the MIB
EVENT-MIB
The EVENT-MIB contains objects to define event triggers and actions for network management
purposes.
EXPRESSION-MIB
The EXPRESSION-MIB contains objects to define expressions of MIB objects for network management
purposes.
FR-MFR-MIB
The FR-MFR-MIB provides objects to control and monitor the multilink frame relay (MFR) function
described in FRF.16.
HC-RMON-MIB
The HC-RMON- MIB augments the original RMON MIB as specified in RFC 1757 and RFC 1513. The
RMON2 MIB as specified in RFC 2021.RMON AND RMON2 are defined in RMON (RFC 1757) and
the Token Ring RMON MIB (RFC 1513) and the RMON2 MIB (RFC 2021])
The MIB module for managing remote monitoring device implementations. The HC-RMON- MIB
module enhances the original RMON MIB as specified in RFC 1757 and RFC 1513 standards. and also
the RMON2 MIB as specified in the RFC 2021 standard.
IEEE8021-CFM-MIB
The IEEE8021-CFM-MIB is a Connectivity Fault Management (CFM) module for managing IEEE
802.1ag
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-103
Chapter 3
Cisco 7600 MIB Specifications
IEEE8021-PAE-MIB
IEEE8021-PAE-MIB
The IEEE8021-PAE-MIB is the Port Access Entity module for managing IEEE 802.1X.
IEEE8023-LAG-MIB
The IEEE 8023-LAG- MIB is the Link Aggregation module for managing IEEE Std 802.3ad.
IF-MIB (RFC 2863)
The IF-MIB (RFC 2863) describes the attributes of physical and logical interfaces (network interface
sub-layers). The router supports the ifGeneralGroup of MIB objects for all layers (ifIndex, ifDescr,
ifType, ifSpeed, ifPhysAddress, ifAdminStatus, ifOperStatus, ifLastChange, ifName,
ifLinkUpDownTrapEnable, ifHighSpeed, and ifConnectorPresent).
One of the most commonly used identifiers in SNMP-based network management applications is the
Interface Index (ifIndex) value. IfIndex is a unique identifying number associated with a physical or
logical interface.
IGMP-MIB
The IGMP-MIB manages Internet Group Management Protocol (IGMP).
IMA-MIB
The IMA-MIB manages ATM Forum Inverse Multiplexing for ATM (IMA) interfaces
INT-SERV-GUARANTEED-MIB
The INT-SERV-GUARANTEED-MIB describes the guaranteed service of the Integrated Services
Protocol (ISP).
INT-SERV-MIB
The INT-SERV-MIB describes the Integrated Services Protocol (ISP).
INTEGRATED-SERVICES-MIB
The INTEGRATED-SERVICES-MIB contains objects to manage the Integrated Services Protocol
Cisco 7600 Series Router MIB Specifications Guide
3-104
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
IP-FORWARD-MIB
IP-FORWARD-MIB
The IP-FORWARD-MIB contains objects to control the display of CIDR multipath IP Routes.
IP-MIB
The IP-MIB module contains objects for managing IP and ICMP implementations, but excluding their
management of IP routes.
IPMROUTE-MIB
The IPMROUTE-MIB contains objects to manage IP multicast routing on the router, independent of the
actual multicast routing protocol in use.
IPMROUTE-STD-MIB
The IPMROUTE-STD-MIB contains objects to manage IP multicast routing, but independent of the
specific multicast routing protocol in use.
LLDP-MIB
The LLDP-MIB contains objects to manage LLDP configuration, statistics, local system data and remote
systems data components.
MPLS-LDP-MIB
The MPLS-LDP-MIB provides management information for the Multiprotocol Label Switching (MPLS)
Label Distribution Protocol (LDP), which is used by label switching routers (LSRs) to communicate the
definitions of labels that each router is using. The MPLS-LDP-MIB provides objects that perform the
following actions:
•
Configures LDP sessions on a specific LSR
•
Records information that is learned through discovery or from the session initialization message
•
Shows the actual sessions that are established or are being established
Note
The MIB is based on Revision 08 of the IETF MPLS-LDP-MIB.
This MIB is not included in release 12.2(33)SRC. It is replaced by MPLS-LDP-STD-MIB and
MPLS-LDP-GENERIC-STD-MIB (RFC 3815).
For detailed MPLS MIB object support and usage, go to the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120limit/120st/120st21/ld
pmib21.htm
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-105
Chapter 3
Cisco 7600 MIB Specifications
MPLS-LDP-MIB
MIB Constraints
Table 3-32 lists the constraints that the Cisco 7600 Series router places on objects in the
MPLS-LDP-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-32
MPLS-LDP-MIB Constraints
MIB Object
Notes
mplsLdpGeneralGroup
•
mplsLdpLsrId
Read-only.
•
mplsLdpLsrLoopDetectionCapable
Read-only. Loop Detection is supported by
hopCountAndPathVector(5).
mplsLdpEntityIndexNext
Read-only. Returns a value of 0.
•
mplsLdpEntityTable
•
mplsLdpEntityProtocolVersion
Read-only.
•
mplsLdpEntityAdminStatus
Read-only. If adjacency is directed, value is
always enabled(1).
•
mplsLdpEntityOperStatus
Read-only. If adjacency is directed, then the
operation status is always enabled(1). The
adjacency does not appear in this table if
operation status is down.
•
mplsLdpEntityTcpDscPort
Read-only.
•
mplsLdpEntityUdpDscPort
Read-only.
•
mplsLdpEntityMaxPduLength
Read-only.
•
mplsLdpEntityKeepAliveHoldTimer
Read-only.
•
mplsLdpEntityHelloHoldTimer
Read-only.
•
mplsLdpEntityInitSesThreshold
Read-only. Default value is 8.
•
mplsLdpEntityLabelDistMethod
Read-only.
•
mplsLdpEntityLabelRetentionMode
Read-only. If LC-ATM then values are
conservative(1) otherwise liberal(2). If
directed, then the value is liberal(2).
•
mplsLdpEntityPVLimitMisTrapEnable
Read-only.
•
mplsLdpEntityPVL
Read-only.
•
mplsLdpEntityHopCountLimit
Read-only.
•
mplsLdpEntityTargPeer
Read-only.
•
mplsLdpEntityTargPeerAddrType
Read-only. Value is ipv4(1).
•
mplsLdpEntityTargPeerAddr
Read-only.
•
mplsLdpEntityOptionalParameters
Read-only. If LC-ATM, then values are
atm(2), otherwise generic(1). If directed,
then the value is generic(1).
•
mplsLdpEntityDiscontinuityTime
Read-only.
•
mplsLdpEntityStorType
Read-only. Value is volatile(2).
•
mplsLdpEntityRowStatus
Read-only. Value is active(1).
Cisco 7600 Series Router MIB Specifications Guide
3-106
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
MPLS-LDP-MIB
Table 3-32
MPLS-LDP-MIB Constraints (continued)
MIB Object
Notes
mplsLdpEntityConfGenLRTable
Read-only. This table contains entries for
every enabled LDP interface that is not an
LC-ATM.
•
mplsLdpEntityConfGenLRMin
Not-accessible. Index value.
•
mplsLdpEntityConfGenLRMax
Not-accessible. Index value.
•
mplsLdpEntityConfGenifIndexOrZero
Read-only. Always 0.
•
mplsLdpEntityConfGenLRStorType
Read-only. Value is volatile(2).
•
mplsLdpEntityConfGenLRRowStatus
Read-only. Value is active(1).
mplsLdpEntityAtmParmsTable
Not implemented. Cisco 7600 does not
support LC-ATM enabled interfaces.
mplsLdpEntityConfAtmLRTable
Not implemented. Cisco 7600 does not
support LC-ATM enabled interfaces
mplsLdpEntityFrParmsTable
Not implemented.
mplsLdpEntityConfFrLRTable
Not implemented.
mplsLdpEntityStatsTable
•
mplsLdpAttemptedSessions
Read-only.
•
mplsLdpSesRejectedNoHelloErrors
Read-only.
•
mplsLdpSesRejectedAdErrors
Read-only.
•
mplsLdpSesRejectedMaxPduErrors
Read-only.
•
mplsLdpSesRejectedLRErrors
Read-only.
•
mplsLdpBadLdpIdentifierErrors
Read-only.
•
mplsLdpBadPduLengthErrors
Read-only.
•
mplsLdpBadMessageLengthErrors
Read-only.
•
mplsLdpBadTlvLengthErrors
Read-only.
•
mplsLdpMalformedTlvValueErrors
Read-only.
•
mplsLdpKeepAliveTimerExpErrors
Read-only.
•
mplsLdpShutdownNotifReceived
Read-only.
•
mplsLdpShutdownNotifSent
Read-only.
mplsLdpPeerTable
•
mplsLdpPeerLabelDistMethod
Read-only.
•
mplsLdpPeerLoopDetectionForPV
Read-only. Value is enabled(1).
•
mplsLdpPeerPVL
Read-only.
mplsLdpHelloAdjanceyTable
•
mplsLdpHelloAdjHoldTimeRem
Read-only.
•
mplsLdpHelloAdjType
Read-only.
•
mplsLdpSesUpDownTrapEnable
Read-write.
mplsLdpSessionTable
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-107
Chapter 3
Cisco 7600 MIB Specifications
MPLS-LDP-ATM-STD-MIB (RFC 3815)
Table 3-32
MPLS-LDP-MIB Constraints (continued)
MIB Object
Notes
•
mplsLdpSesState
Read-only.
•
mplsLdpSesProtocolVersion
Read-only.
•
mplsLdpSesKeepAliveHoldTimeRem
Read-only.
•
mplsLdpSesMaxPduLen
Read-only.
•
mplsLdpSesDiscontinuityTime
Read-only.
mplsLdpAtmSesTable
Not implemented. Cisco 7600 does not
support LC-ATM enabled interfaces
mplsLdpFrameRelaySesTable
Not implemented.
mplsLdpSesStatsTable
•
mplsLdpSesStatsUnkMesTypeErrors
Read-only.
•
mplsLdpSesStatsUnkTlvErrors
Read-only.
mplsFecTable
Not implemented.
mplsFecIndexNext
Not implemented.
mplsLdpSesInLabelMapTable
Not implemented.
mplsLdpSesOutLabelMapTable
Not implemented.
mplsLdpSesXCMapTable
Not implemented.
mplsXCsFecsTable
Not implemented.
mplsLdpSesPeerAddrTable
Not implemented.
Important information about using the MPLS-LDP-MIB:
The mplsLdpEntityTable is used to configure the LSR for using LDP. There must be at least one LDP entity for the LSR to
support LDP. Each row in this table refers to a single LDP entity.
Entries in the mplsLdpEntityConfGenericTable refer to configured Generic Labels on LDP entities. An LDP entity can have
zero or more generic labels.
The mplsLdpEntityFrameRelayParmsTable contains Frame Relay specific information and parameters for LDP entities. The
mplsLdpEntityConfFrLRTable provides a mechanism for specifying a range of DLCI values, or a label range for LDP
entities.
The mplsLdpEntityStatsTable enhances the mplsLdpEntityTable and contains statistics about the LDP entities in the LSR.
The mplsLdpEntityPeerTable contains information about LDP peers in the mplsLdpEntityTable. This information is
based on information gathered through Entity-Peer interaction.
The mplsLdpSessionTable represents a table of sessions between LDP entities and LDP peers and contains information about
these sessions. The mplsHelloAdjacencyTable is a table of Hello Adjacencies for Sessions. A session can have one or
more Hello Adjacencies. The mplsLdpFrameRelaySessionTable relate Sessions to its label range intersections. The
mplsLdpSessionStatsTable augments the mplsLdpSessionTable and contains statistics about each Session between a
LDP entities and a LDP peer. The mplsLdpSesPeerAddressTable extends the mplsLdpSessionTable and is used to store
Label Address Information from Label Address Messages received by this LSR from Peers.
The Cisco 7600 router does not support LC-ATM (label-controlled) interfaces.
MPLS-LDP-ATM-STD-MIB (RFC 3815)
The MPLS-LDP-ATM-STD-MIB (RFC 3815) contains managed object definitions for configuring and
monitoring the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP), utilizing
Asynchronous Transfer Mode (ATM) as the Layer 2 media.
Cisco 7600 Series Router MIB Specifications Guide
3-108
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
MPLS-LDP-GENERIC-STD-MIB (RFC 3815)
MPLS-LDP-GENERIC-STD-MIB (RFC 3815)
The MPLS-LDP-GENERIC-STD-MIB (RFC 3815)- This MIB contains managed object definitions for
configuring and monitoring the Multiprotocol Label Switching (MPLS), Label Distribution Protocol
(LDP), utilizing ethernet as the Layer 2 media.
MPLS-LDP-STD-MIB (RFC 3815)
The MPLS-LDP-STD-MIB (RFC 3815) contains managed object definitions for the Multiprotocol Label
Switching, Label Distribution Protocol, (LDP) document.
MPLS-LSR-MIB
The MPLS-LSR-MIB provides configuration and remote performance monitoring information to
manage label switched paths (LSPs) through a label switching router (LSR) that is using the
Multiprotocol Label Switching (MPLS) technology. The router supports Version 5 of the
IETF MPLS-LSR-MIB. This MIB is not included in release 12.2(33)SRC. It is replaced by
MPLS-LSR-STD-MIB.
MIB Constraints
Table 3-33 lists the constraints that the Cisco 7600 Series router places on objects in the
MPLS-LSR-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-33
MPLS-LSR-MIB Constraints
MIB Object
Notes
mplsInterfaceConfTable
•
mplsInterfaceConfStorageType
Default read-only (5).
•
mplsInterfaceAvailableBandwidth
Read-only. Always 0.
•
mplsInterfaceTotalBandwidth
Read-only. Always 0.
•
mplsInterfaceTotalBuffer
Read-only. Always 0.
•
mplsInterfaceAvailableBuffer
Read-only. Always 0.
mplsInterfacePerfTable
•
mplsInterfaceInPackets
Read-only. Always 0.
•
mplsInterfaceInDiscards
Read-only. Always 0.
•
mplsInterfaceFailedLabelLookup
Read-only. Always 0.
•
mplsInterfaceOutPackets
Read-only. Always 0.
•
mplsInterfaceOutDiscards
Read-only. Always 0.
•
mplsInterfaceOutFragments
Read-only. Always 0.
mplsInSegmentTable
•
mplsInSegmentAdminStatus
Read-only. Always up(1).
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-109
Chapter 3
Cisco 7600 MIB Specifications
MPLS-LSR-MIB
Table 3-33
MPLS-LSR-MIB Constraints (continued)
MIB Object
Notes
•
mplsInSegmentOperStatus
Always up(1).
•
mplsInSegmentNPop
Read-only.
•
mplsInSegmentAddrFamily
Read-only.
•
mplsInSegmentOwner
Read-only. Other(1)
•
mplsInSegmentTrafficParamPtr
Read-only. Always 0.
•
mplsInSegmentRowStatus
Read-only. Active(5).
•
mplsInSegmentStorageType
Read-only(5).
mplsInSegmentPerfTable
•
mplsInSegmentOctets
Read-only. Always 0.
•
mplsInSegmentPackets
Read-only. Always 0.
•
mplsInSegmentHCOctets
Read-only. Always 0.
•
mplsInSegmentErrors
Read-only. Always 0.
•
mplsInSegmentDiscards
Read-only. Always 0.
mplsOutSegmentTable
•
mplsOutSegmentifIndex
Read-only.
•
mplsOutSegmentPushTopLabel
Read-only. Always False(2).
•
mplsOutSegmentTopLabel
Read-only.
•
mplsOutSegmentNextHopIpAddrType
Read-only.
•
mplsOutSegmentNextHopIpv4Addr
Read-only. Always ipv4(1).
•
mplsOutSegmentNextHopIpv6Addr
Read-only. Always 0.
•
mplsOutSegmentOwner
Read-only. Other(1).
•
mplsOutSegmentTrafficParamPtr
Read-only. Always 0.
•
mplsOutSegmentRowStatus
Read-only. Active(5).
•
mplsOutSegmentStorageType
ReadOnly(5).
•
mplsOutSegmentAdminStatus
Read-only. Always up(1).
•
mplsOutSegmentOperStatus
Always up(1).
mplsOutSegmentPerfTable
•
mplsOutSegmentOctets
Read-only. Always 0.
•
mplsOutSegmentPackets
Read-only. Always 0.
•
mplsOutSegmentHCOctets
Read-only. Always 0.
•
mplsOutSegmentErrors
Read-only. Always 0.
•
mplsOutSegmentDiscards
Read-only. Always 0.
•
mplsOutSegmentPerfDiscontinuityTime
Read-only. Always 0.
mplsXCTable
•
mplsXCLspId
Read-only. Does not support tunnel IDs.
Cisco 7600 Series Router MIB Specifications Guide
3-110
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
MPLS-LSR-MIB
Table 3-33
MPLS-LSR-MIB Constraints (continued)
MIB Object
Notes
•
mplsXCLabelStackIndex
Read-only. Value will be set to 0 because
XCLabelStack is not supported.
•
mplsXCIsPersistent
Read-only. Value is false(2).
•
mplsXCOwner
Read-only. Other(1).
•
mplsXCRowStatus
Read-only. Value is active(1).
•
mplsXCStorageType
Read-only.
•
mplsXCAdminStatus
Read-only. Always up(1).
•
mplsXCOperStatus
Always up(1).
•
mplsOutSegmentIndexNext
Read-only. Always 0.
•
mplsXCIndexNext,
Read-only. Always 0.
•
mplsLabelStackIndexNext
Read-only. Always 0.
•
mplsTrafficParamIndexNext
Read-only. Always 0.
mplsLabelStackTable
Not implemented.
mplsTrafficParamTable
Not implemented.
•
mplsInSegmentTrapEnable
Read-only. Always False(2).
•
mplsOutSegmentTrapEnable
Read-only. Always False(2).
•
mplsXCTrapEnable
Read-only. Always False(2).
•
mplsXCUp
*Not implemented.
•
mplsXCDown
*Not implemented.
•
mplsInSegmentUp
*Not implemented.
•
mplsInSegmentDown
*Not implemented.
•
mplsOutSegmentUp
*Not implemented.
•
mplsOutSegmentDown
*Not implemented.
* Not supported because of scalability issues.
mplsInterfaceConfTable—Provides information for each MPLS-capable interface on an LSR.
mplsInterfacePerfTable—Augments the MPLS interface configuration table.
mplsInSegmentTable—Contains a description of incoming segments (labels) at an LSR and their associated parameters.
Administrative and operational status objects for this table control packet transmission. If administrative and
operational status objects are down, the LSR does not forward packets. If these status objects are up, the LSR forwards
packets.
mplsInSegmentPerfTable—Augments the MPLS in-segment table, providing performance information and counters for
incoming segments on an LSR.
mplsOutSegmentTable—Contains a description of outgoing segments from an LSR and their associated parameters.
Administrative and operational status objects for this table control packet transmission. If administrative and
operational status objects are down, the LSR does not forward packets. If these values are up, the LSR forwards packets.
mplsOutSegmentPerfTable—Augments the MPLS out-segment table, providing performance information and counters for
outgoing segments on an LSR.
mplsXCTable—Associates inSegments (labels) to outSegments (labels) to show the manager how the LSR is currently
swapping these labels. A row in this table consists of one cross-connect entry that is indexed by the cross-connect index,
the interface index of the incoming segment, the incoming label, and the out-segment index. The administrative and
operational objects for this table control packet forwarding to and from a cross-connect entry (XCEntry). The
administrative status and operational status are always up in the Cisco implementation. Otherwise, the LSR would not
forward packets.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-111
Chapter 3
Cisco 7600 MIB Specifications
MPLS-LSR-STD-MIB (RFC 3031)
MPLS-LSR-STD-MIB (RFC 3031)
The MPLS-LSR-STD-MIB (RFC 3031) contains managed object definitions for the Multiprotocol Label
Switching (MPLS) Router.
MPLS-L3VPN-STD-MIB
The MPLS-L3VPN-STD-MIB contains managed object definitions for the Layer-3 Multiprotocol Label
Switching Virtual Private Networks. This MIB is based on RFC 4382 specification.
MPLS-TC-MIB
The MPLS-TC-MIB defines Textual Conventions and OBJECT-IDENTITIES for use in documents
defining management information bases (MIBs) for managing MPLS networks.
MPLS-TE-MIB
The MPLS-TE-MIB enables the Cisco 7600 Series router to perform traffic engineering for MPLS
tunnels. The MIB is based on Revision 05 of the IETF MPLS-TE-MIB.
Traffic engineering support for MPLS tunnels requires the following configuration:
•
Setting up MPLS tunnels with appropriate configuration parameters.
•
Configuring tunnel loose and strict source routed hops.
MIB Constraints
Table 3-34 lists the constraints that the Cisco 7600 Series router places on objects in the
MPLS-TE-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-34
MPLS-TE-MIB Constraints
MIB Object
Notes
mplsTunnelIndexNext
Read-only. Always 0.
mplsTunnelTable
•
mplsTunnelName
Read-only.
•
mplsTunnelDescr
Read-only.
•
mplsTunnelIsif
Read-only.
•
mplsTunnelXCPointer
Read-only.
•
mplsTunnelSignallingProto
Read-only.
•
mplsTunnelSetupPrio
Read-only. Always 7.
•
mplsTunnelHoldingPrio
Read-only. Always 7.
•
mplsTunnelSessionAttributes
Read-only.
Cisco 7600 Series Router MIB Specifications Guide
3-112
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
MPLS-TE-MIB
Table 3-34
MPLS-TE-MIB Constraints (continued)
MIB Object
Notes
•
mplsTunnelOwner
Read-only.
•
mplsTunnelLocalProtectInUse
Read-only. Always false(2).
•
mplsTunnelResourcePointer
Read-only.
•
mplsTunnelInstancePriority
Read-only. Always 0.
•
mplsTunnelHopTableIndex
Read-only.
•
mplsTunnelIncludeAnyAffinity
Read-only. Always 0.
•
mplsTunnelIncludeAllAffinity
Read-only.
•
mplsTunnelExcludeAllAffinity
Read-only.
•
mplsTunnelPathInUse
Read-only.
•
mplsTunnelRole
Read-only.
•
mplsTunnelTotalUpTime
Read-only.
•
mplsTunnelInstanceUpTime
Read-only. Always 0.
•
mplsTunnelAdminStatus
Read-only.
•
mplsTunnelRowStatus
Read-only. Always readOnly(5).
•
mplsTunnelStorageType
Read-only. Volatile (2). Always active.
mplsTunnelHopListIndexNext
Read-only. Always 0.
mplsTunnelHopTable
•
mplsTunnelHopAddrType
Read-only. Always ipv4(1).
•
mplsTunnelHopIpv4Addr
Read-only.
•
mplsTunnelHopIpv4PrefixLen
Read-only. Always 32.
•
mplsTunnelHopIpv6Addr
Read-only. NULL.
•
mplsTunnelHopIpv6PrefixLen
Read-only. Always 0.
•
mplsTunnelHopAsNumber
Read-only.
•
mplsTunnelHopLspId
Read-only.
•
mplsTunnelHopType
Read-only. Always strict(1).
•
mplsTunnelHopRowStatus
Read-only. Always active(1).
•
mplsTunnelHopStorageType
Read-only. Value is readOnly(5).
mplsTunnelResourceIndexNext
Read-only. Always 0.
mplsTunnelResourceTable
•
mplsTunnelResourceMaxRate
Read-only.
•
mplsTunnelResourceMeanRate
Read-only.
•
mplsTunnelResourceMaxBurstSize
Read-only.
•
mplsTunnelResourceRowStatus
Read-only. Always active(1).
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-113
Chapter 3
Cisco 7600 MIB Specifications
MPLS-VPN-MIB
Table 3-34
MPLS-TE-MIB Constraints (continued)
MIB Object
•
Notes
mplsTunnelResourceStorageType
Read-only. Value is readOnly(5).
The mplsTunnelTable allows new MPLS tunnels to be created between an MPLS LSR and a remote endpoint and existing
tunnels to be reconfigured or removed. The Cisco 7600 supports point-to-point tunnel segments, although
multi-point-to-point and point-to-multipoint connections are supported by an LSR acting as a cross-connect. Each MPLS
tunnel can have one out-segment originating at an LSR and one in-segment terminating at that LSR. The
mplsTunnelTable is enhanced by the mplsTunnelPerfTable which provides several counters to measure the performance
of the MPLS tunnels.
The mplsTunnelResourceTable indicates the resources required for a tunnel. Multiple tunnels can share the same resources
by pointing to the same entry in this table. Tunnels that do not share resources must point to separate entries in this table.
The mplsTunnelHopTable indicates strict or loose hops for an MPLS tunnel defined in mplsTunnelTable, when you establish
the hop using signaling. Multiple tunnels share the same hops by pointing to the same entry in this table. Each row also
has a secondary index, mplsTunnelHopIndex, corresponding to the next hop of this tunnel. The scalar
mplsTunnelMaxHops indicates the maximum number of hops that you can specify on each tunnel supported by this LSR.
The mplsTunnelARHopTable indicates the actual hops crossed by a tunnel as reported by the MPLS signaling protocol
after the tunnel is setup.
There are three notifications in this MIB module. The notifications mplsTunnelUp and mplsTunnelDown indicate that the
value of mplsTunnelOperStatus has transitioned to up(1) or down(2). The notification mplsTunnelRerouted is generated
when a tunnel is rerouted or re-optimized.
MPLS-VPN-MIB
The MPLS-VPN-MIB:
•
Describes managed objects for modeling a Multiprotocol Label Switching/Border Gateway Protocol
Virtual Private network
•
Configures and monitor routes and route targets for each VRF instance on a router
•
Facilitates provisioning VPN Routing and Forwarding (VRF) instances on MPLS interfaces
•
Measures the performance of MPLS/BGP VPNs
The MIB is based on Revision 05 of the IETF MPLS-VPN-MIB.
MIB Constraints
Table 3-35 lists the constraints that the Cisco 7600 Series router places on objects in the
MPLS-VPN-MIB. For detailed definitions of MIB objects, see the MIB.
Table 3-35
MPLS-VPN-MIB Constraints
MIB Object
Notes
mplsNumVrfSecViolationThreshExceeded
Not implemented.
mplsVpnVrfSecTable
•
mplsVpnVrfSecIllegalLabelViolations
Read-only. Always 0.
•
mplsVpnVrfSecIllegalLabelRcvThresh
Read-only. Always 0.
mplsVpnVrfTable
•
mplsVpnVrfConfRowStatus
Read-only.
•
mplsVpnVrfConfStorageType
Read-only. Volatile(2).
Cisco 7600 Series Router MIB Specifications Guide
3-114
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
MPLS-VPN-MIB
Table 3-35
MPLS-VPN-MIB Constraints (continued)
MIB Object
Notes
•
mplsVpnVrfConfMidRouteThreshold
Read-only.
•
mplsVpnVrfConfHighRouteThreshold
Read-only
•
mplsVpnVrfConfMaxRoutes
Read-only
•
mplsVpnVrfConfMaxPossibleRoutes
Read-only. Always 0.
•
mplsVpnVrfDescription
Read-only
•
mplsVpnInterfaceVpnClassification
Read-only
mplsVpnInterfaceConfTable
•
mplsVpnInterfaceConfStorageType
Read-only. Volatile(2).
•
mplsVpnInterfaceConfRowStatus
Read-only.
Values: active(1), notInService(2).
•
mplsVpnInterfaceLabelEdgeType
Read-only. providerEdge(1).
mplsVpnVrfRouteTargetTable
•
mplsVpnVrfRouteTargetRowStatus
Read-only. Values: active(1), notInService(2).
mplsVpnVrfBgpNbrAddrTable
•
mplsVpnVrfBgpNbrRowStatus
Read-only. Values: active(1), notInService(2).
•
mplsVpnVrfBgpNbrRole
Read-only. providerEdge(1).
•
mplsVpnVrfBgpNbrType
Read-only.
•
mplsVpnVrfBgpNbrAddr
Read-only.
•
mplsVpnVrfBgpNbrStorageType
Read-only. Volatile(2).
mplsVpnVrfRouteTable
•
mplsVpnVrfRouteInfo
Read-only. Value nullOID.
•
mplsVpnVrfRouteTarget
Read-only. Determines the route distinguisher for
this target.
•
mplsVpnVrfRouteTargetDescr
Description of the route target. This object is not
supported in this Cisco IOS release. Therefore, the
object is the same as mplsVpnVrfRouteTarget.
•
mplsVpnVrfRouteDistinguisher
Read-only.
•
mplsVpnVrfRouteNextHopAS
Read-only. Always 0.
•
mplsVpnVrfRouteRowStatus
Read-only. This object normally reads active (1),
but may read notInService (2), if a VRF was
recently deleted.
•
mplsVpnVrfRouteStorageType
Read-only. Volatile(2).
•
mplsVpnVrfRouteDestAddrType
Read-only.
•
mplsVpnVrfRouteMaskAddrType
Read-only.
•
mplsVpnVrfRouteTos
Read-only. Always 0.
•
mplsVpnVrfRouteNextHop
Read-only.
•
mplsVpnVrfRouteNextHopAddrType
Read-only.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-115
Chapter 3
Cisco 7600 MIB Specifications
MSDP-MIB
Table 3-35
MPLS-VPN-MIB Constraints (continued)
MIB Object
Notes
•
mplsVpnVrfRouteifIndex
Read-only.
•
mplsVpnVrfRouteType
Read-only.
•
mplsVpnVrfRouteProto
Read-only.
mplsVpnVrfBgpNbrPrefixTable
Not implemented.
The mplsVpnVrfConfTable represents all the MPLS/BGP VPNs configured. The NMS configures an entry in this table for each
MPLS/BGP VPN configured to run in this MPLS domain. The mplsVPNInterfaceConfTable extends the interface MIB to
provide specific MPLS/BGP VPN information on MPLS/BGP VPN-enabled interfaces. The mplsVPNPerfTable enhances
the mplsVpnVrfConfTable to provide performance information.
The mplsVpnVrfRouteTable and the mplsVpnRouteTargetTable facilitate the configuration and monitoring of routes and route
targets, respectively, for each VRF instance.
MSDP-MIB
The MSDP-MIB contains objects to monitor the Multicast Source Discovery Protocol (MSDP). The
MIB can be used with SNMPv3 to remotely monitor MSDP speakers.
For more information about this MIB, see its feature module description at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t5/dt5msdp.htm
NOTIFICATION-LOG-MIB
The NOTIFICATION-LOG-MIB contains objects for logging SNMP Notifications, that is, Traps and
Informs.
NOVELL-IPX-MIB
The NOVELL-IPX-MIB defines the management information for a system using the IPX protocol. This
MIB is designed to provide a basic framework for the management of systems implementing the
IPX protocol. It is identical to the IPX MIB distributed as a part of the Novell NetWare Link Services
Protocol (NLSP) Specification 1.0, Novell Part Number 100-001708-002, 2nd Edition Feb 1994.
NOVELL-NLSP-MIB
The NOVELL-NLSP-MIB defines the management information for the NLSP protocol that operates in
an IPX environment. It provides information in addition to that information contained in the IPX MIB
itself. This MIB is identical to the NLSP-MIB distributed as a part of the Novell NetWare Link Services
Protocol (NLSP) Specification 1.0, Novell Part Number 100-001708-002, 2nd Edition Feb 1994.
Cisco 7600 Series Router MIB Specifications Guide
3-116
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
NOVELL-RIPSAP-MIB
NOVELL-RIPSAP-MIB
The NOVELL-RIPSAP-MIB defines the management information for the RIP and SAP protocols
running in an IPX environment. It provides information in addition to that contained in the IPX MIB
itself. This MIB is identical to the RIPSAP-MIB distributed as a part of the Novell NetWare Link
Services Protocol (NLSP) Specification 1.0, Novell Part Number 100-001708-002, 2nd Edition
Feb 1994.
OLD-CISCO-APPLETALK-MIB
The OLD-CISCO-APPLETALK-MIB provides information about AppleTalk traffic on the router.
OLD-CISCO-CHASSIS-MIB
The OLD-CISCO-CHASSIS-MIB describes chassis objects in devices running an older implementation
of the Cisco IOS operating system. Those objects are now described in the ENTITY-MIB.
However, the Cisco 7600 Series router implements the OLD-CISCO-CHASSIS-MIB to support older
network management applications that do not implement the ENTITY-MIB.
The router uses this MIB for port adapters, which are not supported in the CISCO-STACK-MIB. It also
contains information about FlexWAN modules. Network management applications that do not support the
ENTITY-MIB can use the OLD-CISCO-CHASSIS-MIB to discover FlexWAN modules and port adapters.
MIB Constraints
The OLD-CISCO-CHASSIS-MIB is deprecated. Chassis objects are now described in the
ENTITY-MIB; therefore, where possible, we recommend that you use the ENTITY-MIB instead of the
OLD-CISCO-CHASSIS-MIB.
Note
The OLD-CISCO-CHASSIS-MIB is supported on the Cisco 7600 Series router for LAN cards, OSM
cards, and FlexWAN/PAs. Currently, SIPs and SPAs are only supported through the ENTITY-MIB,
therefore do not use the older MIBs.
Table 3-36 lists the constraints that the router places on objects in the MIB. For detailed definitions of
MIB objects, see the MIB.
Table 3-36
MIB Object
OLD-CISCO-CHASSIS-MIB Constraints for FlexWAN Modules and Port Adapters
Notes
cardTable
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-117
Chapter 3
Cisco 7600 MIB Specifications
OLD-CISCO-CHASSIS-MIB
Table 3-36
OLD-CISCO-CHASSIS-MIB Constraints for FlexWAN Modules and Port Adapters
MIB Object
•
cardType
Notes
The following values are used for 7600 router cards:
Module or Port Adapter
cardType Value
FlexWAN2 wsx-6582-2pa(689)
FlexWAN wsx_6182_2pa(658)
PA-A3-T3 pa_atmdx_ds3(406)
PA-A3-E3 pa_atmdx_e3(407)
PA-A3-OC-3SML pa_atmdx_sml_OC3(408)
PA-A3-OC-3-SMI pa_atmdx_smi_oc3(409)
PA-A3-OC-3MM pa_atmdx_mm_oc3(410)
PA-MC-4T1 pa_4ct1_csu(428)
PA-MC-8T1 pa_8ct1_csu(429)
PA-MC-E3 pa_ima_t1(569)
PA-A3-8E1IMA pa_ima_e1(570)
PA-MC-T3 pa_mct3(804)
PA-MC-STM-1SMI pa_mc_stm1_smi(817)
PA-MC-STM-1MM pa_mc_stm1_mm(818)
•
cardOperStatus
Port adapter status matches FlexWAN module status, up(2).
•
cardSerial
All zero (0).
•
cardHwVersion
FlexWAN module, 1.3. PAs not applicable.
•
cardSwVersion
FlexWAN module 12.1(13)E. PAs not applicable.
•
cardSlotNumber
•
•
cardContainedByIndex
CardSlots
•
FlexWAN is 2.
•
ATM-OC-3 PA is 0.
•
Channelized STM-1 PA is 1.
•
FlexWAN is 0.
•
ATM-OC-3 PA is 2.
•
Channelized STM-1 PA is 2.
•
FlexWAN is 2.
•
ATM-OC-3 PA is 0.
•
Channelized STM-1 PA is 0.
cardifIndexTable
•
CardifConnectorTypeEnabled Always not-specified(1).
•
cardifSlotNumber
•
•
CardifPortNumber
CardifCardIndex
•
ATM-OC-3 PA is bay# 0.
•
Channelized STM-1 PA is bay # 1.
•
ATM-OC-3 PA is 0.
•
Channelized STM-1 PA is 0.
•
ATM-OC-3 PA is 6.
•
Channelized STM-1 PA is 7.
Entries used for port adapters only. Not used for FlexWAN modules.
Cisco 7600 Series Router MIB Specifications Guide
3-118
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
OLD-CISCO-CPU-MIB
OLD-CISCO-CPU-MIB
The OLD-CISCO-CPU-MIB describes CPU usage and active system processes on devices running an
older implementation of the Cisco IOS operating system.
OLD-CISCO-DECNET-MIB
The OLD-CISCO-DECNET-MIB provides information about the implementation of DECnet on the
router. DECnet is group of communications products (including a protocol suite) developed by Digital
Equipment Corporation that supports the Open System Interconnetion (OSI) protocol and proprietary
Digital protocols.
OLD-CISCO-INTERFACES-MIB
The OLD-CISCO-INTERFACES-MIB contains objects to manage interfaces on devices running an
older implementation of the Cisco IOS operating system.
OLD-CISCO-IP-MIB
The OLD-CISCO-IP-MIB contains objects to manage IP on devices running an older implementation of
the Cisco IOS operating system.
OLD-CISCO-MEMORY-MIB
The OLD-CISCO-MEMORY-MIB contains objects that describe memory pools on devices running an
older implementation of the Cisco IOS operating system.
OLD-CISCO-NOVELL-MIB
The OLD-CISCO-NOVELL-MIB provides information about Novell traffic on the router, including
packet counts and IPX accounting and checkpoint accounting information.
OLD-CISCO-SYS-MIB
The OLD-CISCO-SYS-MIB should only be used in the test tool environment in place of
OLD-CISCO-CPU, OLD-CISCO-ENVMON-MIB, OLD-CISCO-MEMORY-MIB, and
OLD-CISCO-SYSTEM-MIB MIBs.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-119
Chapter 3
Cisco 7600 MIB Specifications
OLD-CISCO-SYSTEM-MIB
OLD-CISCO-SYSTEM-MIB
The OLD-CISCO-SYSTEM-MIB provides information about the router (such as its name, software boot
load and configuration file), and contains controls for reloading software onto the router and clearing the
Address Resolution Protocol (ARP) cache.
OLD-CISCO-TCP-MIB
Starting with Cisco IOS Release 10.2, all objects defined in this MIB have been deprecated. The objects
have been replaced with the objects defined in the CISCO-TCP-MIB. Management applications should
no longer be examining the objects defined in this MIB.
OLD-CISCO-TS-MIB
The OLD-CISCO-TS-MIB provides information about the umber of terminal lines on this device. Also,
includes virtual lines.
OLD-CISCO-VINES-MIB
The OLD-CISCO-VINES-MIB group is present in all router based products. It provides the total input
and output number of vines.
OLD-CISCO-XNS-MIB
The OLD-CISCO-XNS-MIB (present in router-based products) provides the total input number of
XNS packets.
OSPF-MIB
The OSPF-MIB contains objects that describe the OSPF Version 2 Protocol. The RFC1253-MIB
corresponds to the OSPF-MIB (Open Shortest Path First (OSPF) protocol).
OSPF-TRAP-MIB
The OSPF-TRAP-MIB contains objects that describe traps for the OSPF Version 2 Protocol.
PIM-MIB (RFC 2934)
The PIM-MIB contains objects to configure and manage Protocol Independent Multicast (PIM) on the
router. The MIB is extracted from RFC 2934.
Cisco 7600 Series Router MIB Specifications Guide
3-120
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
RFC1213-MIB
MIB Constraints
Table 3-37 lists the constraints that the Cisco 7600 Series router places on objects in the PIM-MIB.
Table 3-37
CISCO-PIM-MIB Constraints
MIB Object
Notes
pimIpMRouteTable
Not implemented
pimIpMRouteNextHopTable
Not implemented
pimInterfaceTable
•
pimInterfaceMode
Read only
•
pimInterfaceHelloInterval
Read only
•
pimInterfaceStatus
Read only
•
pimInterfaceJoinPruneInterval
Read only
•
pimInterfaceCBSRPreference
Read only
pimJoinPruneInterval
Read only
pimCandidateRPTable
•
pimCandidateRPAdressd
Read only
•
pimCandidateRPRowStatus
Read only
pimComponentTable
•
pimComponentCRPHoldTime
Read only
•
pimComponentStatus
Read only
RFC1213-MIB
The RFC1213-MIB defines the second version of the Management Information Base (MIB-II) for use
with network-management protocols in TCP-based internets.
RFC1243-MIB (Appletalk)
The RFC1243-MIB uses the extended OBJECT-TYPE macro as defined in [9], Rose, M., and K.
McCloghrie, Editors, Concise MIB Definitions, RFC 1212, Performance Systems International, Hughes
LAN Systems, March 1991.
RFC1315-MIB (Frame Relay)
The RFC1315-MIB contains objects to manage a Frame Relay data terminal equipment (DTE) interface,
which consists of a single physical connection to the network with many virtual connections to other
destinations and neighbors. The MIB contains the objects used to manage:
•
The Data Link Connection Management Interface (DLCMI)
•
Virtual circuits on each Frame Relay interface
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-121
Chapter 3
Cisco 7600 MIB Specifications
RFC1315-MIB (Frame Relay)
•
Errors detected on Frame Relay interfaces
MIB Constraints
Table 3-38 lists the constraints that the Cisco 7600 Series router places on objects in the RFC1315-MIB.
For detailed definitions of MIB objects, see the MIB. These constraints apply to all frame relay
supported interfaces.
Table 3-38
RFC1315-MIB Constraints
MIB Object
Notes
frDlcmiTable
•
•
frDlcmiState
frDlcmiAddress
Values are:
•
noLmiConfigured(1)
•
ImiRev1(2)
•
ansiT1-617-D(3)
•
itit933A(5) (Note: Value is defined in RFC2115.)
Values are:
•
q922November90(3)
•
q922(4)
Always returns q922November90(3)
•
frDlcmiAddressLen
Value is two-octets(2)
•
frDlcmiMaxSupportedVCs
Read-only. Always returns a value of 992.
frCircuitTable
•
frCircuitCommittedBurst
•
frCircuitExcessBurst
•
frCircuitThroughput
•
Normally, the QoS configuration entered through the
Modular QoS CLI (MQC) syntax does not appear in these
frCircuitTable objects.
However, when QoS is configured through the MQC and
the following conditions are met, these frCircuitTable
objects contain the QoS values as they are entered
through the MQC:
•
The default class is configured on the policy-map
only.
•
An output policy is attached to the Frame Relay (FR)
Permanent Virtual Circuit (PVC).
•
The Cisco-class-based-QoS (CBQ) enhancement
only supports two MQC actions: police cir and
shape.
•
If both police cir and shape actions exist, then the
FR traffic-shaping QoS takes precedence before
policing.
frCircuitState
Cisco 7600 Series Router MIB Specifications Guide
3-122
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
RFC1381-MIB (X25 LAPB)
Table 3-38
RFC1315-MIB Constraints (continued)
MIB Object
Notes
frErrTable
Not implemented.
frDLCIStausChange – No active(3) trap.
This trap is implemented according to the FRAME-RELAY-DTE-MIB (RFC2115). If the reason for the state change is due
to the DLCMI going down, then DLCI traps are not be generated.
RFC1381-MIB (X25 LAPB)
The RFC1381-MIB is the SNMP MIB Extension for X.25 (specifications) LAPB (Link Access
Procedure Balance protocol).
RFC1382-MIB (X25 Packet Layer)
The RFC1382-MIB was extracted from RFC 1382. Several changes were made to the MIB to allow it to
compile in our environment:
•
Remove IMPORT statements for EntryStatus, PositiveInteger, and ifIndexType.
•
Hand-import the above types by copying the definitions from their respective files.
•
The range of x25OperRestartCount is increased to be the largest integer possible.
RFC2006-MIB (MIP)
The RFC2006-MIB is the MIB module for the Mobile IP standard.
RMON-MIB (RFC 1757)
The RMON-MIB contains objects to remotely monitor devices in the network. This MIB supports the
MIB version RFC 1757.
RMON2-MIB (RFC 2021)
The RMON2-MIB contains objects to manage remote monitoring device implementations. This MIB
module enhances the original RMON MIB as specified in RFC 2021.
RS-232-MIB
The RS232-MIB contains objects to manage RS-232-like hardware interfaces and devices.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-123
Chapter 3
Cisco 7600 MIB Specifications
RSVP-MIB
RSVP-MIB
The RSVP-MIB contains objects to manage the Resource Reservation Protocol (RSVP).
SMON-MIB
The SMON-MIB manages remote monitoring device implementations for switched networks. Identifies
the source of the data that the associated function is configured to analyze. This textual convention
extends the data source textual convention defined by RMON 2 to the following data source types:
•
ifIndex
•
smonVlanDataSource
•
entPhysicalEntry
SNA-SDLC-MIB
The SNA-SDLC-MIB contains objects that manage SDLC (synchronous data link control) devices.
SNMP-FRAMEWORK-MIB (RFC 2571)
The SNMP-FRAMEWORK-MIB (RFC 2571) contains objects that describe the SNMP management
architecture. There are no constraints on this MIB.
SNMP-COMMUNITY-MIB (RFC 2576)
The SNMP-COMMUNITY-MIB (RFC 2576) contains objects that help support coexistence between
SNMPv1, SNMPv2c, and SNMPv3.
SNMP-MPD-MIB (RFC 2572)
The SNMP-MPD-MIB (RFC 2572) contains objects for Message Processing and Dispatching.
SNMP-NOTIFICATION-MIB (RFC 2573)
The SNMP-NOTIFICATION-MIB contains managed objects for SNMP v3 notifications. The MIB also
defines a set of filters that limit the number of notifications generated by a particular entity
(snmpNotifyFilterProfileTable and snmpNotifyFilterTable).
Objects in the snmpNotifyTable are used to select entities in the SNMP-TARGET-MIB
snmpTargetAddrTable and specify the types of SNMP notifications those entities are to receive.
Cisco 7600 Series Router MIB Specifications Guide
3-124
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
SNMP-PROXY-MIB
SNMP-PROXY-MIB
The SNMP-PROXY-MIB contains managed objects to remotely configure the parameters used by an
SNMP entity for proxy forwarding operations. The MIB contains a single table, snmpProxyTable, which
defines the translations to use to forward messages between management targets.
SNMP-TARGET-MIB (RFC 2573)
The SNMP-TARGET-MIB (RFC 2573) contains objects to remotely configure the parameters used by
an entity to generate SNMP notifications. The MIB defines the addresses of entities to send SNMP
notifications to, and contains a list of tag values that are used to filter the notifications sent to these
entities (see the SNMP-NOTIFICATION-MIB). There are no constraints on this MIB.
SNMP-USM-MIB (RFC 2574)
The SNMP-USM-MIB (RFC 2574) contains objects that describe the SNMP user-based security model.
SNMP-VACM-MIB (RFC 2575)
The SNMP-VACM-MIB (RFC 2575) contains objects that describe the view-based access control model
for SNMP.
Note
To access the SNMP-VACM-MIB, you must create an SNMP v3 user with access to a view that includes
all of the information from the Internet subtree. For example:
Router(config)# snmp-server view abcview internet included
Router(config)# snmp-server group abcgroup v3 noauth read abcview write abcview
notify abcview
Router(config)# snmp-server user abcuser abcgroup v3
SNMPV2-MIB (RFC 1907)
The SNMPv2-MIB contains objects SNMPv2 entities. The SNMPv2-MIB contains the following
mandatory object groups:
•
SNMP group—Collection of objects providing basic instrumentation and control of an
SNMP entity.
•
System group—Collection of objects common to all managed systems.
•
snmpSetGroup—Collection of objects which allow several cooperating SNMPv2 entities, all acting
in a manager role, to coordinate their use of the SNMPv2 set operation.
•
snmpBasicNotificationsGroup—The two notifications are coldStart and authenticationFailure
which an SNMPv2 entity is required to implement.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-125
Chapter 3
Cisco 7600 MIB Specifications
SONET-MIB (RFC 1595, 2558)
SONET-MIB (RFC 1595, 2558)
The SONET-MIB provides both configuration and performance monitoring objects for SONET
interfaces.
Note
Release 12.2(18)SXF supports RFC 1595 version. Releases 12.2(33)SRA and older support RFC 2558
version
MIB Constraints
Table 3-39 lists the constraints that the Cisco 7600 Series router places on objects in the SONET-MIB.
For detailed definitions of MIB objects, see the MIB.
Table 3-39
SONET-MIB Constraints
MIB Object
Notes
sonetPathCurrentTable
•
sonetPathCurrentWidth
Read-only.
sonetVTCurrentTable
Not implemented.
sonetVTIntervalTable
Not implemented.
sonetFarEndVTCurrentTable
Not implemented.
sonetFarENdVTIntervalTable
Not implemented.
Table
•
csConfig
Not Implemented.
•
csApsConfig
Not implemented.
•
csSection
Not implemented.
•
csLine
Not implemented.
•
csPath
Not implemented.
•
csStats
Not implemented.
•
cspConfig
Not implemented.
SOURCE-ROUTING-MIB (RFC 1525)
The SOURCE-ROUTING-MIB contains objects to configure and manage source routing and source
routing transparent bridges.
TCP-MIB
The TCP-MIB (RFC 2012) contains objects to manage the Transmission Control Protocol (TCP)
implementations on the router. There are no constraints. This MIB is included in the Cisco 7600
executable image, but its support is unverified.
Cisco 7600 Series Router MIB Specifications Guide
3-126
OL-4077-07
Chapter 3
Cisco 7600 MIB Specifications
TUNNEL-MIB
TUNNEL-MIB
The TUNNEL-MIB contains objects to manage IP Tunnels. This MIB is based on RFC 4087
specification.
UDP-MIB
The UDP-MIB (RFC 2013) contains objects to manage the User Datagram Protocol (UDP) on the router.
There are no constraints.
Cisco 7600 Series Router MIB Specifications Guide
OL-4077-07
3-127
Chapter 3
Cisco 7600 MIB Specifications
UDP-MIB
Cisco 7600 Series Router MIB Specifications Guide
3-128
OL-4077-07