Owner`s manual | Cissell L28UR30 Clothes Dryer User Manual

LCD TV PLASMA TV
OWNER’S MANUAL
LCD TV MODELS
PLASMA TV MODELS
32LG30
37LG30
42LG30
42PG25
50PG25
32LG60
37LG60
42LG60
47LG60
52LG60
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency(EPA).
As an ENERGY STAR
Partner LGE U. S. A.,Inc.
has determined that this
product meets the
ENERGY STAR guidelines
for energy efficiency.
37LG50
42LG50
47LG50
52LG50
50PG60
60PG60
32LG70
42LG70
47LG70
52LG70
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
P/NO : SAC30708020 (0803-REV04)
www.lgusa.com / www.lg.ca
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product
1
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate
booklet or sheet, or be located before any operating instructions in an instruction for installation for use and
supplied with the apparatus.
This information shall be given in a language acceptable to the country where the apparatus is intended to be used.
The important safety instructions shall be entitled “Important Safety Instructions”. The following safety
instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety
information may be included by adding statements after the end of the following safety instruction list. At the
manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be
placed immediately adjacent to that safety instruction:
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
1
Do not use this apparatus near water.
2
Clean only with dry cloth.
3
4
5
2
6
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
7
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
8
Only use attachments/accessories specified by
the manufacturer.
9
Unplug this apparatus when unused for long
periods of time.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.
When mounting a TV it on the wall, make sure
not to install TV by the hanging power and signal cables on the back of the TV.
10
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
11
Never touch this apparatus or antenna during
a thunder or lighting storm.
12
Do not allow a impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.
13
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has exposed to rain or moisture,
does not operate normally, or has been
dropped.
14
CAUTION concerning the Power Cord :
Most appliances recommend they be placed
upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and
has no additional outlets or branch circuits.
Check the specification page of this owner's
manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use
of the appliance, and have the cord replaced
with an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
15
Outdoor use marking :
WARNING - To reduce the risk of fire or electric shock, do not expose this appliance to rain
or moisture.
16
Wet Location Marking : Apparatus shall not be
exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall
be placed on or over apparatus.
17
GROUNDING
Ensure that you connect the earth ground wire
to prevent possible electric shock. If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas pipes.
Power
Supply
Short-circuit
Breaker
18
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The
plug must remain readily operable.
3
CONTENTS
WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Protection Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Securing the TV to the wall to prevent falling . . . . 21
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 22
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Audio Out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
WATCHING TV / CHANNEL CONTROL
Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Turning On the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4
Channel Setup
- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
- Add / Delete Channel (Manual Tuning) . . . . . . 57
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
USB
Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 72
Preset Picture Settings
- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Manual Picture Adjustment
- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 76
- Picture Mode - Expert Control . . . . . . . . . . . . . . . . . . 77
Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 78
Advanced Control - Black (Darkness) Level . . . . . . . 79
Advanced Control - Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Advanced - Real Cinema/Film Mode . . . . . . . . . . . . . . . . . 81
Advanced - TruMotion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
TruMotion Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Image Sticking Minimization (ISM) Method . . . . . . 86
Power Saving Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
SOUND & LANGUAGE CONTROL
APPENDIX
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 88
Preset Sound Settings (Sound Mode) . . . . . . . . . . . . . . 89
Sound Setting Adjustment - User Mode . . . . . . . . . . . 90
Clear Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
On-Screen Menus Language Selection . . . . . . . . . . . . . . 97
Caption Mode
- Analog Broadcasting System Captions . . . . . . . 98
- Digital Broadcasting System Captions . . . . . . . . 99
- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Programming the Remote Control . . . . . . . . . . . . . . . . . . 124
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
External Control Through RS-232C . . . . . . . . . . . . . . . . .129
Open Source License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
TIME SETTING
Clock Setting
- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
5
FEATURE OF THIS TV
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.
Manufactured under license from Dolby Laboratories.
“Dolby “and the double-D symbol are trademarks of
Dolby Laboratories.
FOR LCD TV
■
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is
nothing wrong with TV.
■ Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they
have no adverse effect on the monitor's performance.
■ Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce
some temporary distortion effects on the screen.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with
general household waste. Disposal of this product must be carried out in accordance to the regulations of your local
authority.
6
PREPARATION
ACCESSORIES
TV
Q.
PO
ST
MEN B
U
U
RE
TU
RN
AV
VO
1
L
FA
V
CH
MU
TE
2
4
E
ER
VC
IN R
PU
T
D
A
G
MO
DE
P
3
5
7
W
DV
MEN
EN
TE
R
6
8
9
0
FLASH
BK
1.5V 1.5V
Copyright© 2007 LGE,
All Rights Reserved.
Owner’s Manual
Remote Control,
Batteries
CD Manual
PREPARATION
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
Power Cord
Option Extras
* Wipe spots on the exterior only with
the polishing cloth.
* Do not wipe roughly when removing
Polishing Cloth
stain. Please be cautions of that
(This feature is not available
excessive pressure may cause scratch
for all models.)
or discoloration.
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.
For Plasma TV models
(Only 50PG25,
50/60PG60)
x4
Bolts for stand assembly
(Refer to P.14)
Cable Holder
(Only 42PG25)
Cable Management Clip
(Only 42PG25)
Protection Cover
(Refer to P.20)
For LCD TV models
32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70
(Only 32/37/42LG30, 37/42LG50,
32/42LG70)
(Only 32LG30/70)
or
x4
x4
Bolts for stand assembly
(Refer to P.14)
Screw for stand fixing
(Refer to P.18)
Protection Cover
(Refer to P.20)
32/37/42/47/52LG60
(Only 32/37LG60)
(Only 42LG60)
or
32LG60: 3EA
37LG60: 4EA
4EA
2EA
(M4x16)
Bolts for stand assembly
(Refer to P.15)
1EA
4EA
(M4x20)
Protection Cover
(Refer to P.20)
Cable Management
Clip
7
PREPARATION
FRONT PANEL INFORMATION
■
Image shown may differ from your TV.
■
NOTE: If your TV has a protection tape attached, remove the tape.
And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).
PREPARATION
Plasma TV Models
Remote Control Sensor
POWER Button
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
MENU
INPUT
INPUT
INPUT
MENU
VOL
ENTER
MENU
MENU
Button
INPUT
Button
VOL
ENTER
VOL
ENTER
CH
CH
ENTER
Button
CH
VOLUME
(-, +) Buttons
CHANNEL
(E,D)Buttons
LCD TV Models
32/42/47/52LG70
CH
Intelligent Sensor
Adjusts picture according to the surrounding
conditions
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using P o w e r I n d i c a t o r in
the OPTION menu. G p.85)
Remote Control Sensor
POWER Button
8
VOL
CHANNEL (
Buttons
VOLUME (+, -)
Buttons
ENTER
ENTER Button
MENU
INPUT
,
MENU Button
INPUT Button
)
LCD TV Models
CH
Intelligent Sensor (Except 32/37/42LG30)
Adjusts picture according to the surrounding
conditions
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using P o w e r I n d i c a t o r in
the OPTION menu. G p.85)
VOL
CHANNEL (
Buttons
,
)
PREPARATION
32/37/42LG30, 37/42/47/52LG50
VOLUME (+, -)
Buttons
ENTER
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
Remote Control Sensor
POWER Button
32/37/42/47/52LG60
CH
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
POWER Button
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates white when the set is switched on.
(Can be adjusted using P o w e r I n d i c a t o r in
the OPTION menu. G p.85)
VOL
CHANNEL (
Buttons
,
)
VOLUME (+, -)
Buttons
ENTER Button
ENTER
MENU Button
MENU
INPUT Button
INPUT
9
PREPARATION
BACK PANEL INFORMATION
■
Image shown may differ from your TV.
HDMI IN 4
USB IN
10
1
R
VIDEO L/MONO AUDIO
RR
PREPARATION
Plasma TV Models
12
9
AV IN 2
5
3
1
6
ANTENNA/
CABLE IN
4
RGB IN
HDMI/DVI IN
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
DIGITAL AUDIO OUT
OPTICAL COAXIAL
7
3
2
1
1
AUDIO
VIDEO
2
10
S-VIDEO
2
AUDIO OUT
(
)
(
)
AUDIO
VIDEO
(MONO)
8
AV IN 1
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
9
R
R
PREPARATION
LCD TV Models
12
5
ANTENNA/
CABLE IN
3
USB
SERVUCE ONLY
32/37/42LG30
6
DIGITAL
AUDIO OUT
OPTICAL
HDMI/DVI IN
7
RS-232C IN
(CONTROL & SERVICE)
2
2
1
1
AUDIO OUT
8
AUDIO
VIDEO
S-VIDEO VIDEO
(MONO)
AUDIO
AV IN 1
(
COMPONENT IN
VIDEO L/MONO AUDIO R
REMOTE
CONTROL IN
R
AUDIO
(RGB/DVI)
RGB(PC)
1
HDMI IN 3
4
RGB IN
)
9
11
1
9
AV IN 2
2
5
ANTENNA/
CABLE IN
3
USB IN
37/42/47/52LG50
6
10
REMOTE
CONTROL IN
HDMI/DVI IN
1
COAXIAL
RS-232C IN
(CONTROL & SERVICE)
7
AUDIO OUT
8
2
1
AUDIO
VIDEO
COMPONENT IN
S-VIDEO VIDEO
(MONO)
AUDIO
AV IN 1
2
OPTICAL
9
(
)
VIDEO L/MONO AUDIO R
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
RGB(PC)
1
HDMI IN 3
4
RGB IN
1
9
AV IN 2
2
11
R
PREPARATION
■
Image shown may differ from your TV.
R
LCD TV Models
32/42/47/52LG70
1
ANTENNA/
CABLE IN
6
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
3
OPTICAL
7
COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
8
AV IN 1
2
2
1
1
AUDIO
VIDEO
COMPONENT IN
(
S-VIDEO VIDEO
(MONO)
AUDIO
)
1
VIDEO L/MONO AUDIO R
HDMI/DVI IN
HDMI IN 4
4
RGB IN
10
USB IN
5
3
9
R
PREPARATION
12
9
AV IN 2
R
2
12
(RGB/DVI)
COAXIAL
OPTICAL
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
6
REMOTE
CONTROL IN
12
4
7
RGB(PC)
USB IN
HDMI IN 4
DIGITAL
AUDIO OUT
3
AUDIO
HDMI/DVI IN
2
RGB IN
1
1
3
VIDEO L/MONO AUDIO R
11
VIDEO
2
AUDIO
COMPONENT IN
1
2
32/37/42/47/52LG60
AV IN
10
(
1
9
)
2
3
HDMI/DVI IN, HDMI IN
Digital Connection.
Supports HD video and Digital audio. Doesn’t
support 480i.
Accepts DVI video using an adapter or HDMI to
DVI cable (not included)
COMPONENT IN
Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red
and white for audio.
RGB (PC)
Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).
AUDIO (RGB/DVI)
1/8” headphone jack for analog PC audio input.
4
REMOTE CONTROL IN PORT
For a wired remote control.
5
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
6
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
7
DIGITAL AUDIO OUT
Digital audio output for use with amps and home
theater systems.
Includes an optical and/or coaxial connection.
Note: In standby mode, these ports do not work.
8
AUDIO OUT
Analog audio output for use with amps and home
theater systems.
9
AV (Audio/Video) IN
Analog composite connection. Supports standard
definition video only (480i).
S-VIDEO
Better quality than standard composition.
Supports standard definition video only (480i).
10
USB INPUT
Used for viewing photos and listening to MP3s.
11
USB SERVICE ONLY or RS-232C IN (SERVICE
ONLY)
Used for software updates.
12
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
PREPARATION
1
13
PREPARATION
STAND INSTALLATION
■
Image shown may differ from your TV.
Only 42PG25
Only 32/37/42LG30, 37/42LG50, 32/42LG70
PREPARATION
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the TV as shown.
2
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
STAND BODY
COVER BASE
3
14
Fix the 4 bolts securely using the holes in the
back of the TV.
3
Assemble the TV as shown.
4
Fix the 4 bolts securely using the holes in the
back of the TV.
Only 32/37/42LG60
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
32LG60
PREPARATION
1
37LG60
42LG60
STAND BODY
STAND BODY
(M4x16)
STAND BODY
COVER BASE
COVER BASE
3
Assemble the TV as shown.
4
Fix the 4 bolts securely using the holes in the
back of the TV.
COVER BASE
(M4x20)
15
PREPARATION
CABLE MANAGEMENT
■
Image shown may differ from your TV.
PREPARATION
Plasma TV Models
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
Install the CABLE MANAGEMENT CLIP as
shown.
If your TV has the CABLE HOLDER, install it
as shown and bundle the cables.
CABLE HOLDER
CABLE MANAGEMENT CLIP
How to remove the CABLE MANAGEMENT CLIP
42PG25
G
First, press the cable management. Hold the
C A B L E M A N A G E M E N T C L I P with both
hands and pull it upward.
50PG25, 50/60PG60
G
Hold the CABLE MANAGEMENT CLIP with both
hands and pull it upward.
G
Separate C A B L E M A N A G E M E N T C L I P from TV
by pressing two latches.
! NOTE
G
16
Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken.
LCD TV Models
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
Install the CABLE MANAGEMENT CLIP as
shown.
32/37/42/47/52LG60
1
Align the hole with the tab on the C A B L E
M A N A G E M E N T C L I P.
Turn the C A B L E M A N A G E M E N T C L I P as
shown.
Note: This cable management clip can be broken by excessive pressure.
2
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
PREPARATION
32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70
CABLE MANAGEMENT CLIP
3
Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.
17
PREPARATION
DESKTOP PEDESTAL INSTALLATION
■
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
PREPARATION
4 inches
4 inches
CAUTION
4 inches
4 inches
G
Ensure adequate ventilation by following the clearance recommendations.
SWIVEL STAND
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.
ATTACHING THE TV TO A DESK (Only 32LG30/70)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.
Stand
1-Screw
(provided as parts of the product)
Desk
WARNING
G
18
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
VESA WALL MOUNTING
PREPARATION
This TV accepts VESA FDMI compliant mounts via the four screw holes on the back of the TV.
We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
Plasma TV Models
400 mm
(Except 60PG60: 600 mm)
R
400 mm
LCD TV Models
32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70
32/37/42/47/52LG60
200 mm
(Except 52LG50/70: 800 mm)
200 mm
(Except 52LG60: 800 mm)
)
R
32LG30/70: 100 mm
37LG30/50: 200 mm
42LG30/50/70: 200 mm
47LG50/70: 200 mm
52LG50/70: 400 mm
32LG60: 100 mm
37/42/47LG60: 200 mm
52LG60: 400 mm
R
(
! NOTE
G
Screw length needed depends on the wall mount used. For further information, refer to the instructions
included with the mount.
(
)
19
PREPARATION
PROTECTION COVER
■
Image shown may differ from your TV.
PREPARATION
You can remove the stand before installing the TV on a wall mount by performing the previous stand instructions
in reverse. After removing the stand, install the included p r o t e c t i o n c o v e r over the hole for the stand.
Insert the P R O T E C T I O N C O V E R into the TV until clicking sound.
Plasma TV Models
LCD TV Models
After removing the protection paper from the
protection cover, adhere it to the TV as shown.
20
SECURING THE TV TO THE WALL TO PREVENT FALLING
■
■
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
PREPARATION
You should purchase necessary components to prevent TV from falling off of the stand.
Image shown may differ from your TV.
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it
becomes horizontal between the wall and the product.
! NOTE
G
G
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
21
PREPARATION
■
To prevent damage do not connect to the power outlet until all connections are made between the devices.
ANTENNA OR CABLE CONNECTION
R
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connection.
For optimum picture quality, adjust antenna direction if needed.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA/
CABLE IN
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
R
PREPARATION
1. Antenna (Analog or Digital)
Copper Wire
Be careful not to bend the copper wire
when connecting the antenna.
(
)
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
R
RF Coaxial Wire (75 ohm)
)
To improve the picture quality in a poor signal area, please purchase a signal amplifier( and
install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
ANTENNA/
CABLE IN
UHF
Signal
Amplifier
Antenna
VHF
(
22
)
EXTERNAL EQUIPMENT SETUP
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
■
Image shown may differ from your TV.
HD RECEIVER SETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do
receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
EXTERNAL EQUIPMENT SETUP
Component Connection
1. How to connect
1
2
Connect the video outputs (Y, PB, PR) of the digital settop box to the C O M P O N E N T I N V I D E O 1 jacks on
the TV. Match the jack colors (Y = green, PB = blue, and
PR = red).
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O 1 jacks on the TV.
2. How to use
■
■
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box. operation)
Select the C o m p o n e n t 1 input source on the TV using
the I N P U T button on the remote control.
If connected to C O M P O N E N T I N 2 input, select the
C o m p o n e n t 2 input source on the TV.
Supported Resolutions
Signal
Y, CB/PB, CR/PR
Component
HDMI
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
1080p
Yes
Yes
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480i
15.73
15.73
59.94
60.00
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.94
60.00
23
EXTERNAL EQUIPMENT SETUP
Plasma TV, 32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70
Y
PB
PR
L
R
EXTERNAL EQUIPMENT SETUP
2
1
RGB IN
DIGI
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
OPT
RS-232
(CONTROL &
2
Y
PB
PR
R
L
1
AUDIO
VIDEO
S-VIDEO
COMPONENT IN
3
AUDIO
(RGB/DVI)
HDMI/DVI IN
2
1
RGB IN
2
VIDEO
1
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
1
32/37/42/47/52LG60
COAXIAL
2
OPTICAL
RGB(PC)
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
L
24
R
Y
PB
PR
HDMI Connection
1. How to connect
Connect the digital set-top box to H D M I / D V I I N 1,
2 , 3 , or 4 jack on the TV.
2
No separate audio connection is necessary.
HDMI supports both audio and video.
2. How to use
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
■ Select the H D M I 1, H D M I2, H D M I 3, or H D M I 4 input
source on the TV using the INPUT button on the remote
control.
■
EXTERNAL EQUIPMENT SETUP
1
HDMI-DTV
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.939
60.00
25
EXTERNAL EQUIPMENT SETUP
32/37/42LG30, 37/42/47/52LG50
Plasma TV, 32/42/47/52LG70
RGB IN
RGB IN
HDMI/DVI IN
A
(RG
RGB(PC)
RGB(PC)
3
EXTERNAL EQUIPMENT SETUP
HDMI/DVI IN
2
2
2
Y
PR
PB
Y
1
1
VIDEO
COMPONENT
PR
VIDEO
COMPON
1
1
HDMI-DTV OUTPUT
HDMI-DTV OUTPUT
AUDIO
(RGB/DVI)
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
RGB(PC)
HDMI/DVI IN
3
COAXIAL
OPTICAL
HDMI-DTV OUTPUT
2
RGB IN
2
VIDEO
1
DIGITAL
AUDIO OUT
AUDIO
1
COMPONENT IN
1
32/37/42/47/52LG60
26
PB
1
DVI to HDMI Connection
1. How to connect
32/37/42LG30, 37/42/47/52LG50, Plasma TV
- Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1, 2 , or 3 jack on the TV.
32/37/42/47/52LG60, 32/42/47/52LG70
- Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1, 2 , 3 , or 4 jack on the TV.
2
Connect the PC audio output to the A U D I O ( R G B / D V I ) jack on the TV.
2. How to use
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
■ 32/37/42LG30, 37/42/47/52LG50, Plasma TV
- Select the HDMI1, HDMI2, or HDMI3 input source on the TV using the I N P U T button on the remote control.
■ 32/37/42/47/52LG60, 32/42/47/52LG70
- Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the I N P U T button on the remote
control.
■
! NOTE
G
EXTERNAL EQUIPMENT SETUP
1
A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio,
so a separate audio connection is necessary.
27
EXTERNAL EQUIPMENT SETUP
Plasma TV, 32/42/47/52LG70
32/37/42LG30, 37/42/47/52LG50
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
RGB IN
HDMI/DVI IN
REMOTE
CONTROL IN
AUDIO
(RGB/DVI)
RGB(PC)
REMOT
CONTROL
3
R
(CONT
2
2
EXTERNAL EQUIPMENT SETUP
Y
PR
PB
R
L
2
Y
1
1
(
2
PB
PR
1
AUDIO
VIDEO
S
COMPONENT IN
2
1
DVI-DTV OUTPUT
L
DVI-DTV OUTPUT
R
COAXIAL
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
28
L
R
RGB(PC)
HDMI/DVI IN
3
AUDIO
(RGB/DVI)
2
OPTICAL
DVI-DTV OUTPUT
2
RGB IN
VIDEO
1
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
1
2
32/37/42/47/52LG60
1
AUDIO
VIDEO
COMPONENT IN
2
1
R
L
1
L
R
AV IN 1
HDMI/DVI IN
(
)
DVD SETUP
Component Connection
1. How to connect
2
Connect the video outputs (Y, PB, PR) of the DVD to the
C O M P O N E N T I N V I D E O 1 jacks on the TV.
Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O 1 jacks on the TV.
2. How to use
■
■
■
■
Turn on the DVD player, insert a DVD.
Select the C o m p o n e n t 1 input source on the TV using
the I N P U T button on the remote control.
If connected to C O M P O N E N T I N 2 input, select the
C o m p o n e n t 2 input source on the TV.
Refer to the DVD player's manual for operating instructions.
EXTERNAL EQUIPMENT SETUP
1
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
29
EXTERNAL EQUIPMENT SETUP
Plasma TV, 32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70
Y
PB
PR
L
EXTERNAL EQUIPMENT SETUP
1
R
2
RGB IN
DIGITA
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
OPTICA
RS-232C I
(CONTROL & SER
2
Y
PB
PR
R
L
1
AUDIO
VIDEO
S-VIDEO V
COMPONENT IN
3
AUDIO
(RGB/DVI)
HDMI/DVI IN
2
1
RGB IN
2
VIDEO
1
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
1
32/37/42/47/52LG60
COAXIAL
2
OPTICAL
RGB(PC)
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
30
L
R
Y
PB
PR
S-Video Connection (Except 32/37/42/47/52LG60)
AUDIO
S-VIDEO
1
Connect the S-VIDEO output of the DVD to the
S - V I D E O input on the TV.
2
Connect the audio outputs of the DVD to the A U D I O
input jacks on the TV.
L
R
ANTENNA/
CABLE IN
2. How to use
■
■
Turn on the DVD player, insert a DVD.
Select the A V 1 input source on the TV using the I N P U T
button on the remote control.
Refer to the DVD player's manual for operating instructions.
2
UDIO
B/DVI)
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
L
AUDIO OUT
R
AUDIO
N
COAXIAL
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
■
1
DIGITAL AUDIO OUT
EXTERNAL EQUIPMENT SETUP
1. How to connect
31
EXTERNAL EQUIPMENT SETUP
HDMI Connection
32/37/42LG30, 37/42/47/52LG50
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
HDMI/DVI IN
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1, 2 , 3 or 4 jack on the TV.
2
2
Y
2
AUDIO
(RGB/D
RGB(PC)
No separate audio connection is necessary.
HDMI supports both audio and video.
PR
PB
L
1
1
A
VIDEO
COMPONENT IN
2. How to use
■
■
Select the HDMI1, H D M I2, HDMI3, or HDMI4 input
source on the TV using the I N P U T button on the remote
control.
Refer to the DVD player's manual for operating instructions.
1
HDMI-DVD OUTPUT
Plasma TV, 32/42/47/52LG70
2
Y
PB
1
PR
1
VIDEO
COMPONENT
(
DIGITAL
AUDIO OUT
COAXIAL
)
OPTICAL
ANTENNA/
CABLE IN
1
REMOTE
CONTROL IN
HDMI-DVD OUTPUT
HDMI-DVD OUTPUT
32
3
AUDIO
(RGB/DVI)
RS-232C IN
(SERVICE ONLY)
1
2
RGB(PC)
HDMI/DVI IN
COMPONENT IN
2
1
RGB IN
(R
3
AUDIO
RGB(PC)
VIDEO
RGB IN
HDMI/DVI IN
2
1
32/37/42/47/52LG60
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
■ Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period
of time (Plasma TV models only). If the 4:3 picture format is used; the fixed images on the sides of the screen
may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty.
■
1
Connect the RF antenna out socket of the
VCR to the A N T E N N A / C A B L E I N socket on the TV.
Plasma TV, 32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70
ANTENNA/
CABLE IN
UDIO OUT
1
COAXIAL
2
Connect the antenna cable to the RF
antenna in socket of the VCR.
E)
ANT IN
OUTPUT
SWITCH
AV IN 1
2
EO L (MONO) AUDIO R
VIDEO
L
R
Wall Jack
Antenna
32/37/42/47/52LG60
COMP
■
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.)
S-VIDEO
AUDIO OUT
2. How to use
■
ANT OUT
AUDIO
1. How to connect
EXTERNAL EQUIPMENT SETUP
Antenna Connection
COAX
OPTIC
ANTENNA/
CABLE IN
1
S-VIDEO
VIDEO
L
R
ANT OUT
RS-232C IN
(SERVICE ONLY)
ANT IN
OUTPUT
SWITCH
Wall Jack
REMOTE
CONTROL IN
2
Antenna
33
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
Plasma TV, 32/37/42LG30,
37/42/47/52LG50,
32/42/47/52LG70
1. How to connect
EXTERNAL EQUIPMENT SETUP
V I D E O jacks between TV and
Connect the A U D I O/V
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)
1
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
L
R
2. How to use
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
■ Select the A V 1 input source on the TV using the I N P U T
button on the remote control.
■ If connected to A V I N 2, select A V 2 input source on the TV.
■
1
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
COAXIAL
AUDIO OUT
! NOTE
L
If you have a mono VCR, connect the audio cable from
the VCR to the A U D I O L / M O N O jack of the TV.
R
AUDIO
S-VIDEO VIDEO L (MONO) AUDIO R
HDMI IN 4
USB IN
NT IN
VIDEO L/MONO AUDIO R
32/37/42/47/52LG60
1
AV IN
34
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
L
R
AV IN 1
G
S-Video Connection (Except 32/37/42/47/52LG60)
1. How to connect
2
Connect the audio outputs of the VCR to the A U D I O
input jacks on the TV.
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
L
R
2. How to use
■
■
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
Select the A V 1 input source on the TV using the I N P U T
button on the remote control.
ANTENNA/
CABLE IN
2
1
DIGITAL
AUDIO OUT
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
L
! NOTE
G
S-Video provides better quality than composite. Use it
when available.
AUDIO OUT
R
AUDIO
NT IN
COAXIAL
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
Connect the S-VIDEO output of the VCR to the
S - V I D E O input on the TV.
EXTERNAL EQUIPMENT SETUP
1
CAUTION
G
Do not connect to both Video and S-Video at the same
time. In the event that you connect both Video and the
S-Video cables, only the S-Video will work.
35
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
Camcorder
1. How to connect
■
■
Select the A V 2 input source on the TV using
the I N P U T button on the remote control.
If connected to A V I N 1 input, select the A V 1
input source on the TV.
Operate the corresponding external equipment.
L
USB IN
VIDEO
HDMI IN 3
2. How to use
■
36
V I D E O jacks
Connect the A U D I O/V
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
VIDEO L/MONO AUDIO R
EXTERNAL EQUIPMENT SETUP
1
Video Game Set
1
R
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
VGA (D-Sub 15 pin) Connection
N
(CO
2
Y
PB
PR
1
DIGITAL
AUDIO OUT
3
AUDIO
(RGB/DVI)
COAXIAL
R
L
2
OPTICAL
RGB(PC)
1
ANTENNA/
CABLE IN
AUDIO
VIDEO
COMPONENT IN
1
1
2
RS-232C IN
(SERVICE ONLY)
HDMI/D
REMOTE
CONTROL IN
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
VIDEO
RGB IN
AUDIO
COMPONENT IN
32/37/42/47/52LG60
EXTERNAL EQUIPMENT SETUP
Plasma TV, 32/37/42LG30,
37/42/47/52LG50, 32/42/47/52LG70
2
REMOTE
CONTROL IN
RGB OUTPUT
AUDIO
RGB OUTPUT
AUDIO
1. How to connect
1
Connect the VGA output of the PC to the R G B ( P C) jack on the TV.
2
Connect the PC audio output to the A U D I O ( R G B / D V I) jack on the TV.
2. How to use
■
■
Turn on the PC and the TV.
Select the R G B - P C input source on the TV using the I N P U T button on the remote control.
37
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
32/37/42LG30, 37/42/47/52LG50, Plasma TV
- Connect the DVI output of the PC to the H D M I / D V I I N 1, 2 , or 3 jack on the TV.
32/37/42/47/52LG60, 32/42/47/52LG70
- Connect the DVI output of the PC to the H D M I / D V I I N 1, 2 , 3 , or 4 jack on the TV.
2
Connect the PC audio output to the A U D I O ( R G B / D V I ) jack on the TV.
2. How to use
■
■
■
Turn on the PC and the TV.
32/37/42LG30, 37/42/47/52LG50, Plasma TV
- Select the HDMI1, HDMI2, or HDMI3 input source on the TV using the I N P U T button on the remote control.
32/37/42/47/52LG60, 32/42/47/52LG70
- Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the I N P U T button on the remote
control.
! NOTES
38
G
32/37/42LG30, 42/50PG25: To get the the best
picture quality, adjust the PC graphics card to
1360x768.
G
37/42/47/52LG50, 32/37/42/47/52LG60,
32/42/47/52LG70, 50/60PG60: To get the the
best picture quality, adjust the PC graphics card
to 1920x1080.
G
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
G
In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or bright-
ness. If noise is present, change the PC output to
another resolution, change the refresh rate to
another rate or adjust the brightness and contrast
on the PICTURE menu until the picture is clear.
G
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image could become
permanently imprinted on the screen.
G
The synchronization input form for Horizontal and
Vertical frequencies is separate.
32/37/42LG30, 37/42/47/52LG50
Plasma TV, 32/42/47/52LG70
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
RGB IN
HDMI/DVI IN
REMOTE
CONTROL IN
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
3
HDMI/DVI IN
R
(CONT
(CO
2
PR
PB
R
L
Y
1
1
AUDIO
VIDEO
R
L
AUDIO
VIDEO
COMPONENT IN
2
1
2
DVI-PC OUTPUT
AUDIO
DVI-PC OUTPUT
PR
1
S
COMPONENT IN
1
PB
1
AV IN 1
Y
2
EXTERNAL EQUIPMENT SETUP
2
2
AUDIO
1
3
AUDIO
(RGB/DVI)
HDMI/DVI IN
2
RGB IN
2
VIDEO
1
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
1
32/37/42/47/52LG60
COAXIAL
OPTICAL
RGB(PC)
ANTENNA/
CABLE IN
RS-232C IN
2
(SERVICE ONLY)
REMOTE
CONTROL IN
DVI-PC OUTPUT
AUDIO
39
(
)
EXTERNAL EQUIPMENT SETUP
Supported Display Specifications (RGB-PC, HDMI-PC)
! NOTE
EXTERNAL EQUIPMENT SETUP
G
Depending on the graphics card, some resolution settings may not allow the image to be positioned on the
screen properly.
G
If there are overscan in HDMI-PC 1920x1080, change aspect ratio to J u s t s c a n.
For 32/37/42LG30
For 37/42/47/52LG50, 32/37/42/47/52LG60,
32/42/47/52LG70
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.469
70.08
640x350
31.468
70.09
720x400
31.469
70.08
720x400
31.469
70.08
640x480
31.469
59.94
640x480
800x600
37.879
60.31
31.469
37.500
37.861
59.94
75.00
72.80
1024x768
48.363
60.00
1280x768
47.776
59.87
800x600
35.156
37.879
46.875
48.077
56.25
60.31
75.00
72.18
1360x768
47.720
59.799
1366x768
47.130
59.65
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.776
60.289
59.87
74.893
1280x1024
63.981
79.976
60.02
75.025
1360x768
47.712
60.015
1600x1200
75.00
60.00
66.587
59.934
67.5
60.00
* Only RGB-PC mode
1920x1080
RGB-PC
1920x1080
HDMI-PC
* Only RGB-PC mode
40
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.468
70.09
720x400
31.469
70.08
640x480
31.469
37.500
37.861
59.94
75.00
72.80
800x600
35.156
37.879
46.875
48.077
56.25
60.31
75.00
72.18
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.776
60.289
59.87
74.893
1280x1024
63.981
79.976
60.02
75.025
1360x768
47.712
60.015
1600x1200
75.00
60.00
1920x1080
66.587
59.934
EXTERNAL EQUIPMENT SETUP
For 42/50PG25, 50/60PG60
* Only RGB-PC mode
41
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
You can choose the resolution in RGB-PC mode.
The P o s i t i o n, P h a s e, and S i z e can also be adjusted.
EXTERNAL EQUIPMENT SETUP
PICTURE
Move
SCREEN
Enter
E
• Brightness
50
• Sharpness
60
• Color
60
• Tint
0
Resolution
Auto config.
R
G
• Advanced Control
• Reset
Screen (RGB-PC)
Position
Size
Phase
TruMotion Demo
Reset
1 MENU
2
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select R e s o l u t i o n.
3
4
ENTER
5
ENTER
42
Select P I C T U R E.
Select the desired resolution.
Move
G
MENU Prev.
1024 x 768
1280 x 768
1360 x 768
1366 x 768
Only for
32/37/42LG30
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, try using the manual settings or a different resolution or refresh rate on the PC.
Move
SCREEN
Enter
E
• Brightness
50
• Sharpness
60
• Color
60
• Tint
0
Move
MENU Prev.
Resolution
Auto config. G
R
G
• Advanced Control
• Reset
Position
Size
To Set
Yes
No
Screen (RGB-PC)
TruMotion Demo
Phase
Reset
1 MENU
2
Select P I C T U R E.
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select A u t o c o n f i g ..
ENTER
Select Y e s.
3
4
5
ENTER
EXTERNAL EQUIPMENT SETUP
PICTURE
• If the position of the image is still not
correct, try Auto adjustment again.
• If picture needs to be adjusted again
after Auto adjustment in RGB-PC, you
can adjust the P o s i t i o n , S i z e or
P h a s e.
Start Auto Configuration.
43
EXTERNAL EQUIPMENT SETUP
Adjustment for screen Position, Size, and Phase
PICTURE
Move
SCREEN
Enter
E
EXTERNAL EQUIPMENT SETUP
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.
This feature operates only in RGB-PC mode.
• Brightness
50
• Sharpness
60
• Color
60
• Tint
0
Move
MENU Prev.
Resolution
Auto config.
R
G
D
• Advanced Control
Position
• Reset
Size
G
F
G
E
Screen (RGB-PC)
TruMotion Demo
Phase
Reset
1 MENU
2
■
ENTER
Select S c r e e n ( R G B - P C ).
■
3
ENTER
Select P o s i t i o n, S i z e, or P h a s e.
■
4
ENTER
5
ENTER
44
Select P I C T U R E.
Make appropriate adjustments.
P o s i t i o n: This function is to adjust picture to left/right and up/down as you
prefer.
S i z e: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change.
P h a s e : This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters.
Screen Reset (Reset to original factory values)
Returns P o s i t i o n, S i z e, and P h a s e to the default factory settings.
This feature operates only in RGB-PC mode.
Move
SCREEN
Enter
E
• Brightness
50
• Sharpness
60
• Color
60
• Tint
0
Move
MENU Prev.
Resolution
Auto config.
R
G
• Advanced Control
• Reset
Position
To Set
Yes
Size
No
EXTERNAL EQUIPMENT SETUP
PICTURE
Screen (RGB-PC)
Phase
TruMotion Demo
Reset
1 MENU
2
Select P I C T U R E.
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select R e s e t.
3
4
ENTER
G
Select Y e s.
5
ENTER
45
EXTERNAL EQUIPMENT SETUP
USB CONNECTION (Except 32/37/42LG30)
or
1
VIDEO L/MONO AUDIO R
EXTERNAL EQUIPMENT SETUP
HDMI IN 3
USB IN
i.e)
AV IN 2
1. How to connect
1
Connect the USB device to the U S B I N jack on the side
of TV.
2. How to use
■
After connecting the U S B I N jack, you use the USB func-
tion. (G p .64)
46
AUDIO OUT CONNECTION
Send the TV’s audio to external audio equipment via the Audio Output port.
Analog (Except 32/37/42/47/52LG60)
1. How to connect
RS-232C IN
(CONTROL & SERVICE)
S-VIDEO VIDEO L (MONO) AUDIO R
Set the “TV Speaker option - Off ” in the AUDIO menu.
(G p . 9 3). See the external audio equipment instruction
manual for operation.
AV IN 1
AUDIO
2
EXTERNAL EQUIPMENT SETUP
R
Connect audio outputs to the TV’s AUDIO OUT jacks.
1
AUDIO OUT
1
Digital
L
R
AUDIO
1. How to connect
Connect one end of the optical or coaxial cable to the
TV’s O P T I C A L or COAXIAL (Except 32/37/42LG30)
port of D I G ITAL AUDIO OUT.
1
Connect the other end of the optical or coaxial cable to
the digital audio input on the audio equipment.
2
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
UDIO
B/DVI)
Set the “TV Speaker option - Off” in the AUDIO menu. (G
p .93). See the external audio equipment instruction manual for operation.
RS-232C IN 1
(CONTROL & SERVICE)
L
G
When connecting with external audio equipments, such as
amplifiers or speakers, you can turn the TV speakers off in
the menu. (G p . 9 3)
N
COAXIAL
AUDIO OUT
R
AUDIO
! NOTE
OPTICAL
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
3
REMOTE
CONTROL IN
2
CAUTION
G
G
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
Block the SPDIF out (optical/coaxial) about the contents
with ACP(Audio Copy Protection) function.
47
WATCHING TV / CHANNEL CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
TV/STB/DVD/VCR Select the remote operating mode: TV, STB, DVD, or VCR.
POWER Turns your TV or any other programmed equipment on or
off, depending on the mode.
POWER
STB
Q. MENU MENU
DVD
VCR
INPUT
WATCHING TV / CHANNEL CONTROL
Q.MENU Select the desired quick menu source. G p.51
MENU Displays the main menu.
Clear all on-screen displays and return to TV viewing from
any menu.
ENTER
INPUT External input modes rotate in regular sequence.
VOLUME UP Increase/decrease the sound level.
/DOWN
RETURN
AV MODE
FAV Scroll through the programmed Favorite channels. G p.51
FAV
MUTE Switch the sound on or off. G p.50
NUMBER button
— (DASH) Used to enter a program number for multiple
program channels such as 2-1, 2-2, etc.
FLASHBK Tune to the last channel viewed.
VCR/DVD, USB,
SIMPLINK
Control buttons
Control video cassette recorders or DVD players.
Control USB menu (PHOTO LIST and MUSIC LIST.)
Control the SIMPLINK compatible devices.
CH
VOL
CHANNEL Select available channels.
UP/DOWN
PAGE Move from one full set of screen information to the next one.
UP/DOWN
48
TV
MUTE
1
2
3
4
5
6
7
8
9
0
FLASHBK
P
A
G
E
THUMBSTICK Navigate the on-screen menus and adjust the system settings to your preference.
(Up/Down/Left
Right/ENTER)
RETURN Allows the user to move return one step in an interactive application or other user interaction
function.
AV MODE It helps you select and set images and sounds. G p.61
WATCHING TV / CHANNEL CONTROL
SIMPLINK See a list of AV devices connected to TV.
When you toggle this button, the SIMPLINK menu appears at the screen. G p.62-63
Installing Batteries
■
Open the battery compartment cover on the back side and install
the batteries matching correct polarity (+with +,-with -).
■
Install two 1.5V AAA batteries. Don’t mix old or used batteries with
new ones.
■
Close cover.
49
WATCHING TV / CHANNEL CONTROL
TURNING ON THE TV
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
■ In standby mode to turn TV on, press the
)
, INPUT, CH (DE or
), Number
button on the TV or press the POWER, INPUT, CH(
or
( 0~9
9 ) button on the remote control.
1
WATCHING TV / CHANNEL CONTROL
2
Select the viewing source by using the INPUT button on the remote control.
■ This TV is programmed to remember which power state it was last set to,
even if the power cord is out.
3
When finished using the TV, press the POWER button on the remote control.
The TV reverts to standby mode.
! NOTE
G
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
CHANNEL SELECTION
1
Press the C H (
or
) or NUMBER buttons to select a channel number.
VOLUME ADJUSTMENT
Adjust the volume to suit your personal preference.
50
1
Press the V O L ( + or - ) button to adjust the volume.
2
If you want to switch the sound off, press the M U T E button.
3
You can cancel the Mute function by pressing the MUTE or V O L ( + or - )
button.
QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
■
■
■
■
■
■
■
■
■
■
S o u n d M o d e: Selects the factory preset sound for
type of program.
C a p t i o n: Select on or off.
M u l t i A u d i o: Changes the audio language (Digital
signal).
S A P: Selects MTS sound (Analog signal).
S l e e p T i m e r: Select the amount of time before
your TV turns off automatically.
D e l / A d d / F a v: Select channel you want to add/delete
or add the channel to the Favorite List.
U S B E j e c t: Select “USB Eject” in order to eject
USB device.
Plasma TV
LCD TV
Q.Menu
Q.Menu
Aspect Ratio
F
16:9
Power Saving
F
16:9
Off
Clear Voice
Picture Mode
Vivid
Picture Mode
Vivid
Sound Mode
Standard
Sound Mode
Standard
Off
Caption
Multi Audio
Sleep Timer
Off
Del/Add/Fav
Add
USB Eject
Eject
Close
Off
Caption
English
English
Multi Audio
CH
G
3
Backlight
3
Off
Clear Voice
CH
Aspect Ratio
G
WATCHING TV / CHANNEL CONTROL
■
A s p e c t R a t i o: Selects your desired picture format.
P o w e r S a v i n g (Plasma TV Only): Adjusts screen
brightness to reduce the power consumption of the
TV.
B a c k l i g h t (LCD TV Only): Adjust the brightness
of LCD panel to control the brightness of the screen.
C l e a r V o i c e: By differentiating the human sound
range from others, it helps make human voices
sound better.
P i c t u r e M o d e: Selects the factory preset picture
depend on the viewing environment.
Sleep Timer
Off
Del/Add/Fav
Add
USB Eject
Eject
Close
Except 32/37/42LG30
1Q. MENU
Display each menu.
2
3Q. MENU
Make appropriate adjustments.
Return to TV viewing.
51
WATCHING TV / CHANNEL CONTROL
INITIAL SETTING
This Function guides the user to easily set the essential items for viewing the TV for the first time when purchasing the TV. If will be displayed on the screen when turning the TV on for the first time. It can also be activated from the user menus.
■
■
WATCHING TV / CHANNEL CONTROL
H o m e”. We recommend setting the TV to “H
H o m e” mode for the best picture in your
Default selection is “H
home environment.
P i c t u r e menu “II n - s t o r e” Mode is only intended for use in retail environments. Customers can adjust the “P
P i c t u r e m o d e” manually while inspecting the TV, but the TV will automatically return to preset in-store
mode after 5 minutes.
Step1. Mode setting
1
Step1. Mode Setting
!
Select H o m e Mode.
Selecting the environment.
Choose the setting mode you want.
2
Home
In Store
Enter
RETURN
ENTER
Exit
Step2. Time setting
1
Step2. Time Setting
Current Time Setting
Year
Auto
11
Date
15
Hour
5 PM
Minute
Daylight Saving
Enter
Select A u t o or M a n u a l.
G
2007
Month
Time Zone
52
F
2
Select desired time option.
52
Eastern
Off
RETURN Exit
3
ENTER
Step3. Option setting
1
Step3. Option Setting
F
2. Audio Language Setting
English
Select O S D L a n g u a g e S e t t i n g or
A u d i o L a n g u a g e S e t t i n g.
G
French
Enter
RETURN Exit
2
3
Select your desired language.
ENTER
Step4. Auto Tuning
1
Step4. Auto Tuning
Auto Tuning can change channel map.
Do you want to start Auto Tuning?
ENTER
Start A u t o T u n i n g.
WATCHING TV / CHANNEL CONTROL
1. OSD Language Setting
Enter
Enter
RETURN Exit
! NOTE
■
You can also adjust I n i t i a l S e t t i n g in the O P T I O N menu.
53
WATCHING TV / CHANNEL CONTROL
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
All models (Except 32/37/42LG30)
CHANNEL
Move
PICTURE
Enter
Move
Auto Tuning
Aspect Ratio : 16:9
Manual Tuning
Picture Mode : Standard
Channel Edit
AUDIO
Enter
Move
Auto Volume
: Off
Clear Voice
: On
WATCHING TV / CHANNEL CONTROL
• Backlight
80
Balance
• Contrast
90
Sound Mode
• Brightness
50
• SRS TruSurround XT: Off
• Sharpness
60
• Treble
50
• Color
60
• Bass
50
• Tint
0
R
0
Move
Language
E
TIME
Enter
Clock
Input Label
CHANNEL
: On
PICTURE
AUDIO
TIME
Move
Off Time
: Off
On Time
: Off
: Off
Sleep Timer : Off
Caption
: Off
Auto Sleep : Off
ISM Method
: Normal
Power Saving
: Level 0
Set ID
:1
LOCK
INPUT
Enter
: Feb/21/2008 2:10 AM
Key Lock
OPTION
R
• Reset
G
: English
SIMPLINK
L
: Standard
E
OPTION
Enter
USB
E
LOCK
Move
Lock System
: Off
INPUT
Enter
Lock System
: Off
Move
USB
PHOTO LIST
MUSIC LIST
Set Password
Set Password
Cable
Block Channel
Block Channel
AV1
Movie Rating
TV Rating-English
AV2
TV Rating-Children
TV Rating-French
Component1
TV Rating-General
Downloadable Rating
Component2
Downloadable Rating
Input Block
RGB-PC
Input Block
Enter
Antenna
Move
Enter
HDMI1
E
For USA
1 MENU
2
ENTER
Display each menu.
Select a menu item.
! NOTE
G
G
3
ENTER
4 MENU
54
For Canada
Enter to the pop up menu.
G
Return to TV viewing.
I S M M e t h o d, P o w e r S a v i n g: Only
P l a s m a T V.
Backlight, Power Indicator,
T r u M o t i o n D e m o: Only L C D T V.
(But, T r u M o t i o n D e m o : Only for
32/37/42/47/52LG60, 32/42/47/52LG70)
S e t I D: Except 3 2 / 3 7 / 4 2 / 4 7 / 5 2 L G 6 0.
Only for 32/37/42LG30
CHANNEL
Move
Enter
PICTURE
Move
Auto Tuning
Aspect Ratio : 16:9
Manual Tuning
Picture Mode : Standard
Channel Edit
AUDIO
Enter
Move
Auto Volume
: Off
Clear Voice
: On
• Backlight
80
Balance
• Contrast
90
Sound Mode
• Brightness
50
• SRS TruSurround XT: Off
• Sharpness
60
• Treble
50
• Color
60
• Bass
50
0
R
Move
Clock
R
• Reset
G
E
TIME
L
: Standard
WATCHING TV / CHANNEL CONTROL
• Tint
0
Enter
E
Enter
: Feb/21/2008 2:10 AM
Off Time
: Off
On Time
: Off
CHANNEL
PICTURE
AUDIO
TIME
OPTION
LOCK
Sleep Timer : Off
Auto Sleep : Off
OPTION
Language
Move
Enter
: English
Input Label
LOCK
Move
Lock System
: Off
Lock System
Set Password
Set Password
: Off
SIMPLINK
: On
Block Channel
Block Channel
Key Lock
: Off
Movie Rating
TV Rating-English
Caption
: Off
TV Rating-Children
TV Rating-French
Set ID
:1
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Power Indicator
Initial Setting
: Home
Input Block
For USA
1 MENU
2
Enter
ENTER
3
ENTER
4 MENU
For Canada
Display each menu.
Select a menu item.
Enter to the pop up menu.
Return to TV viewing.
55
WATCHING TV / CHANNEL CONTROL
CHANNEL SETUP
Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the
channel list.
Run Auto Tuning again after any Antenna/Cable connection changes.
WATCHING TV / CHANNEL CONTROL
CHANNEL
Move
Enter
Move
Auto Tuning
Manual Tuning
Manual Tuning
Channel Edit
Channel Edit
Enter
Press ‘Yes’ button to begin
auto tuning.
Yes
No
1 MENU
2
ENTER
Select C H A N N E L.
Select A u t o T u n i n g.
3
ENTER
4
ENTER
5RETURN
MENU
56
CHANNEL
Auto Tuning
Select Y e s.
Run A u t o t u n i n g.
Return to the previous menu.
Return to TV viewing.
■
A password is required to gain access to
Auto Tuning menu if the Lock System is
turned on.
Add/Delete Channel (Manual Tuning)
If selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality
of the signal being received.
CHANNEL
Move
Enter
CHANNEL
Move
Auto Tuning
Manual Tuning
Manual Tuning
Channel Edit
Channel Edit
DTV
F
G
Select channel type and
RF-channel number.
Channel
2
DTV 2-1
Bad
Normal
Good
Delete
Close
1 MENU
2
Select C H A N N E L.
Select M a n u a l T u n i n g.
ENTER
3
■
ENTER
Select D T V, T V, C A D T V, or C A T V.
4
WATCHING TV / CHANNEL CONTROL
Auto Tuning
Enter
A password is required to gain access to
Manual Tuning menu if the Lock System
is turned on.
Select channel you want to add
or delete.
5
ENTER
6RETURN
MENU
Select A d d or D e l e t e.
Return to the previous menu.
Return to TV viewing.
57
WATCHING TV / CHANNEL CONTROL
CHANNEL SETUP
Channel Editing
A custom list can be created by toggling each channel on or off with ENTER button. The channels in the Custom
List are displayed in black and the channels deleted from the Custom List are displayed in gray.
Once a channel is highlighted you can add or delete the channel by referring to the small window at the topright corner of the screen.
WATCHING TV / CHANNEL CONTROL
CHANNEL
Move
Enter
Auto Tuning
Manual Tuning
Channel Edit
Add/Delete
1 MENU
2
Select C H A N N E L.
ENTER
Select C h a n n e l E d i t.
ENTER
Select a channel.
3
4
ENTER
5 MENU
RETURN
58
Select channel you want to add or
delete.
Return to the previous menu.
Return to TV viewing.
Move
CH
Move Page
MENU Previous
RETURN Exit
INPUT LIST
Only these input signals which are connected to a TV can be activated and selected.
Antenna
Cable
ENTER
AV2
Component1
Select the desired input source.
You can also select the desired input source in the I N P U T menu
(Except 32/37/42LG30).
■
32/37/42LG30, 37/42/47/52LG50
Antenna
Cable
HDMI3
AV1
AV2
HDMI2
Component1
HDMI1
Component2
RGB-PC
Plasma TV, 32/42/47/52LG70
Antenna
Cable
HDMI4
AV1
AV2
HDMI3
HDMI2
Component1
HDMI1
Component2
RGB-PC
WATCHING TV / CHANNEL CONTROL
1 INPUT
AV1
32/37/42/47/52LG60
Antenna
Cable
HDMI4
AV
HDMI3
Component1
HDMI2
HDMI1
ie)
Cable
AV1
AV2
Q.MENU
■
■
■
■
■
RGB-PC
Disconnected input is inactivated.
Antenna
■
Component2
Component1
Input Label
RETURN
Exit
Select a desired input source (except
A n t e n n a or C a b l e). Then, you can select
your desired Input Label with using Q. MENU
button. G p.60
A n t e n n a: Select it to watch over-the-air broadcasts.
C a b l e: Select it to watch cable and digital cable.
A V: Select them to watch a VCR or other external equipment.
C o m p o n e n t: Select them to watch DVD or a Digital set-top box.
R G B - P C: Select it to view PC input.
H D M I: Select them to watch high definition devices.
59
WATCHING TV / CHANNEL CONTROL
INPUT LABEL
You can set a label for each input source when it's not in use.
OPTION
Move
Language
Enter
: English
Input Label
SIMPLINK
: On
Key Lock
: Off
AV1
F
G
AV1
F
AV
G
AV2
AV2
Component1
Component1
Component1
Component2
Component2
Component2
RGB-PC
WATCHING TV / CHANNEL CONTROL
Caption
: Off
ISM Method
: Normal
RGB-PC
RGB-PC
HDMI1
Power Saving
: Level 0
HDMI1
HDMI1
HDMI2
Set ID
:1
HDMI2
HDMI2
HDMI3
HDMI3
HDMI3
HDMI4
E
G
HDMI4
Close
Close
Close
32/37/42LG30,
37/42/47/52LG50
32/37/42/47/52LG60
Plasma TV, 32/42/47/52LG70
With using OPTION menu
With using INPUT button
1 MENU
1 INPUT
2
3
Select O P T I O N.
ENTER
Select I n p u t L a b e l.
ENTER
Select the source.
3RETURN
MENU
Select the label.
5RETURN
■
Select the label.
Return to the previous menu.
Return to TV viewing.
Return to the previous menu.
MENU
■
Select the source.
2Q. MENU
4
Return to TV viewing.
When new external device is connected, this popup menu is displayed automatically.
If selecting Y e s, you can select input source that you want to appreciate.
S I M P L I N K - O n”, popup menu for HDMI input will not be displayed.
But, when selecting “S
!
New external device is connected.
Do you want to enjoy this?
!
Select input source that you want to appreciate.
AV1
Yes
No
AV2
Component1
60
F
AV MODE
You can select the optimal images and sounds.
2
Cinema
Game
Sport
Press the A V M O D E button repeatedly to select the desired source.
ENTER
■
■
WATCHING TV / CHANNEL CONTROL
1AV MODE
Off
C i n e m a” in AV mode,
If you select “C
C i n e m a will be selected both for “PICTURE menu - Picture Mode” and “AUDIO
menu - Sound Mode” respectively.
O f f” in AV mode, the
If you select “O
P i c t u r e M o d e” and “S
S o u n d M o d e”
“P
return to previous selected value.
61
WATCHING TV / CHANNEL CONTROL
This function operates only with devices with the
logo.
The TV might not function properly when using it with other products with HDMI-CEC function.
This allows you to control and play other AV devices connected with HDMI cable without additional cables and
settings.
To start using SIMPLINK, turn it on in the user menus.
OPTION
Move
WATCHING TV / CHANNEL CONTROL
Language
Enter
: English
Input Label
OPTION
Move
Language
Enter
: English
Input Label
SIMPLINK
Off
: On
SIMPLINK
Key Lock
: Off
Key Lock
: Off
Caption
: Off
Caption
: Off
ISM Method
: Normal
ISM Method
: Normal
Power Saving
: Level 0
Power Saving
: Level 0
:1
Set ID
Set ID
E
: On
On
:1
E
1 MENU
Select O P T I O N.
2
ENTER
Select S I M P L I N K.
ENTER
Select O n or O f f.
3
4RETURN
MENU
Return to the previous menu.
Return to TV viewing.
! NOTE
Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the
SIMPLINK device with the HDMI cable.
G When you switch the Input source with the INPUT button on the remote control, the SIMPLINK device
will stop.
G When you select a device with home theater functionality, the sound output automatically switches to
the home theater speakers.
G If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITAL
AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIMPLINK device with an OPTICAL cable.
G
62
SIMPLINK Functions
D i r e c t P l a y : After connecting AV devices to the TV, you can directly control the devices and play media without additional settings.
■ S e l e c t A V d e v i c e : Enables you to select one of the AV devices connected to TV.
■ D i s c p l a y b a c k : Control connected AV devices by pressing the
, ENTER, G, A, l l, FF and GG buttons.
■ P o w e r o f f a l l d e v i c e s : When you power off the TV, all connected devices are turned off.
■ S w i t c h a u d i o - o u t : Offers an easy way to switch audio-out.
■ S y n c P o w e r o n : When you play the connected AV device, TV will automatically turn on.
(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide
this function)
Note: To operate SIMPLINK, an HDMI cable over Version 1.2 with *CEC function should be used. (*CEC: Consumer
Electronics Control).
■
Display S I M P L I N K menu.
TV
2
ENTER
Select the desired device.
WATCHING TV / CHANNEL CONTROL
1
3
ENTER
Control connected AV devices.
SIMPLINK Menu
1
2
3
4
5
T V v i e w i n g: Switch to the previous TV
channel regardless of the current mode.
D I S C p l a y b a c k: Select and play discs.
When multiple discs are available, the titles
of discs are conveniently displayed at the
bottom of the screen.
V C R p l a y b a c k: Control the connected
VCR.
H D D R e c o r d i n g s p l a y b a c k: Control
recordings stored in HDD.
A u d i o O u t t o H o m e T h e a t e r s p e a ke r / A u d i o O u t t o T V: Select Home
Theater speaker or TV speaker for Audio
Out.
1
2
G
3
4
G
G
5
When no device is connected
(displayed in gray)
Selected Device
When a device is connected
(displayed in bright color)
63
USB
* This feature is only for 37/42/47/52LG50, 32/37/42/47/52LG60, 32/42/47/52LG70, Plasma TV.
ENTRY MODES
When you connect a USB device, this screen is displayed automatically.
In USB device, you can not add a new folder or delete the existing folder.
1 Connect the USB device to the U S B
IN
jacks on the side of TV.
■
USB IN
■
It doesn’t support USB HDD
This TV supports JPG and MP3.
USB
MI IN 3
When removing the USB device
2
Select the U S B E j e c t menu before removing the
USB device.
Select P H O T O L I S T or M U S I C L I S T
PHOTO LIST
3
MUSIC LIST
1Q. MENU
2
Select U S B E j e c t.
ENTER
ENTER
Precautions when using the USB device
G
G
G
G
G
G
G
G
64
Only a USB storage device is recognizable.
If the USB storage device is connected through a
USB hub, the device is not recognizable.
A USB storage device using an automatic recognition program may not be recognized.
A USB storage device which uses its own driver
may not be recognized.
In case of a card reader, up to four memory cards
are concurrently recognizable.
The recognition speed of a USB storage device
may depend on each device.
Please do not turn off the TV or unplug the USB
device when the connected USB storage device is
working. When such device is suddenly separated
or unplugged, the stored files or the USB storage
device may be damaged.
Please do not connect the USB storage device
which was artificially maneuvered on the PC. The
device may cause the product to malfunction or
fail to be played. Never forget to use only a USB
storage device which has normal music files or
image files.
G
G
G
G
G
G
Please use only a USB storage device which was
formatted as a FAT or NTFS file system provided
with the Windows operating system. In case of a
storage device formatted as a different utility program which is not supported by Windows, it may
not be recognized.
Please connect power to a USB storage device
which requires an external power supply. If not,
the device may not be recognized.
Please connect a USB storage device with cable is
offered by USB maker. If connected with cable is
not offered by USB maker or an excessively long
cable, the device may not be recognized.
Some USB storage devices may not be supported
or operated smoothly.
File alignment method of USB storage device is
similar to Window XP and filename can recognize
up to 100 English characters.
Please backup important files because data on
USB device may be damaged. Data management is
consumer's responsibility and as a result, the manufacturer does not cover data damage.
PHOTO LIST
You can view .JPG files from USB storage devices.
The On Screen Display on your model may be slightly different.
Supported photo file: *.JPG
■
■
You can play JPG files only.
Only baseline scan is supported among JPG.
USB
Screen Components
1 MENU
Select U S B.
2
ENTER
Select P H O T O L I S T.
ENTER
3
1
2
Moves to upper level file
Preview: Display the
thumbnail/folder name of
the photo in the selected
folder
4
5
USB Device
PHOTO LIST
Page 1/1
No Marked
Free Space 150MB
TOP FOLDER
Drive1
Drive1
2
1
3
Current page/Total pages
4
Total number of marked photos
5
Usable USB memory
6
Corresponding buttons on
the remote control
1
2Folders, 4Files
Upper
Navigate
PopUp Menu
CH
Move Page
FAV
Mark
RETURN
Exit
6
65
USB
Photo Selection and Popup Menu
PHOTO LIST
USB Device
Page 1/1
No Marked
Free Space 150MB
TOP FOLDER
Drive1
Drive1
2Folders, 4Files
USB
Upper
Navigate
PopUp Menu CH
PHOTO LIST
Move Page
FAV
Mark
RETURN Exit
USB Device
Page 1/1
No Marked
Free Space 150MB
Drive1
Butterfly
Upper
Photo
X.Box
1366x768
125KB
View
Mark All
1366x768 125KB
Delete
Cancel
Upper
Navigate
1
PopUp Menu CH
Move Page
FAV
Mark
RETURN Exit
When you select a file (not folder), this PopUp
menu is displayed.
G V i e w: Display the selected item.
G Mark All: Mark all photos on the screen.
G U n m a r k A l l: Deselect all marked photos.
G D e l e t e: Delete the selected photo item.
G C a n c e l: Close the pop-up menu.
Select the target folder or drive.
■
2
ENTER
3
ENTER
4
66
Select the desired photos.
Show the Popup menu.
ENTER
Select the desired Popup menu.
Use the C H
button to navigation in the
photo page.
■ Use the F A V button to mark or unmark a
photo. When one or more photos are marked,
you can view individual photos or a slide show
of the marked photos. If no photos are marked,
you can view all photos individually or all photos in the folder in a slide show.
Full Screen Menu
You can change the Photo List view so that it fills the screen. More operations are available in full
screen mode.
PHOTO LIST
USB Device
Page 1/1
No Marked
Free Space 150MB
TOP FOLDER
Drive1
Drive1
USB
2Folders, 4Files
Upper
Navigate
Move Page
PopUp Menu CH
PHOTO LIST
FAV
Mark
RETURN Exit
USB Device
Page 1/1
No Marked
Free Space 150MB
Drive1
Butterfly
Upper
Photo
X.Box
1366x768
125KB
View
Mark All
1366x768 125KB
Delete
1/17
Cancel
Upper
Sideshow
Navigate
1
Move Page
FAV
Mark
RETURN Exit
Delete
Option
Hide
The aspect ratio of a photo may change the size of
the photo displayed on the screen in full size.
Select the target folder or drive.
2
ENTER
3
ENTER
4
5
PopUp Menu CH
BGM
Select the desired photos.
Show the Popup menu.
Select V i e w.
ENTER
The selected photo is displayed in
full size.
■
Use the C H
photo page.
button to navigation in the
67
USB
6
ENTER
Select the Sideshow, B G M,
D e l e t e, Option, or Hide.
(Rotate),
■
1/17
Sideshow
BGM
Delete
Option
Hide
Use
button to select the previous or
next photo.
■ Use
button to select and control
the menu on the full-sized screen.
USB
S i d e s h o w: Selected photos are displayed during the
slide show. If no photo is selected, all photos in the current folder are displayed during slide show.
■ Set the time interval of the slide show in O p t i o n.
■ A slide show continues for a maximum of 4 hours.
After 4 hours, the slide show will end and go to TV
mode or external input mode.
G B G M: Listen to music while viewing photos in full size.
■ Set the BGM device and album in O p t i o n.
( R o t a t e ): Rotate photos.
G
■ Rotates the photo 90°, 180°, 270°, 360° clockwise.
G D e l e t e: Delete photos.
G O p t i o n: Set values for S l i d e S p e e d and M u s i c
F o l d e r.
■ Use
button and E N T E R button to set values.
Then go to
and press E N T E R to save the settings.
■ You cannot change M u s i c F o l d e r while BGM is
playing.
G H i d e : Hide the menu on the full-sized screen.
■ To see the menu again on the full-sized screen, press
E N T E R button to display.
G
68
Press F G to set the time interval between slides.
Slide Speed
Fast
Music Folder
...
ENTER
Cancel
! NOTE
G
This TV will not be able to decode
most JPEG images saved using the
Progressive option.
MUSIC LIST
You can use the Music List menu to play MP3 files form a USB storage device.
This TV cannot play back copy-protected files.
The On Screen Display on your model may be slightly different.
USB
Supported music file: *.MP3
Bit rate range 40Kbps ~ 320Kbps
• Sampling rate (Sampling Frequency)
MPEG1 : 32000, 44100, 48000Hz
MPEG2 : 16000, 24000, 22050Hz
MPEG2.5 : 16 ~ 48KHz
Screen Components
1 MENU
2
Select U S B.
ENTER
Select M U S I C L I S T.
ENTER
3
1
2
3
Moves to upper level file
4
Total number of marked
musics
5
Usable USB memory
6
Corresponding buttons on
the remote control
USB Device
MUSIC LIST
Preview: If any album jacket
for the file exists, this jacket is displayed.
Current page/Total pages
5
4
Page 1/1
No Marked
Free Space 150MB
Title
Drive1
Arirang
Play Time
Upper
2
Arirang
04:12
Good Bye
05:30
3945 KB, 128 Kbps
1
Upper
Navigate
PopUp Menu
CH
Move Page
FAV
Mark
RETURN
Exit
6
69
USB
Music Selection and Popup Menu
Up to 6 music titles are listed per page.
MUSIC LIST
USB Device
Page 1/1
No Marked
Drive1
Free Space 150MB
Title
Arirang
Play Time
Upper
Arirang
04:12
Good Bye
05:30
3945 KB, 128 Kbps
Upper
USB
Navigate
PopUp Menu CH
MUSIC LIST
Move Page
FAV
Mark
RETURN Exit
USB Device
Page 1/1
No Marked
Drive1
Free Space 150MB
Title
Arirang
Play Time
Upper
3945 KB
128 Kbps
Arirang
Play
Good Bye
Play with Photo
Mark All
3945 KB, 128 Kbps
Delete
Upper
Navigate
1
Move Page
FAV
Mark
RETURN Exit
Select the target folder or drive.
2
ENTER
3
ENTER
4
5RETURN
70
Cancel
PopUp Menu CH
Select the desired musics.
Show the Popup menu.
ENTER
Select the desired Popup menu.
Return to TV viewing
P l a y (During stop): Play the selected music.
Once a song finishes playing, the next selected
one will be played. When there are no selected
musics to play, the next one in the current folder will be played. If you go to a different folder
and press the E N T E R button, the current
music in playback will stop.
G P l a y M a r k e d: Play the selected musics. Once
a music finishes playing, the next selected one
will be played automatically.
G S t o p P l a y (During playback): Stop the playing musics.
G P l a y w i t h P h o t o: Start playing the selected
musics and then move to the Photo List.
G M a r k A l l: Mark all musics in the folder.
G U n m a r k A l l: Deselect all marked music.
G D e l e t e: Delete the selected music.
G C a n c e l: Close the pop-up menu.
G
■
Use the C H
button to navigation in
the music page.
■ Use F A V button to mark or unmark a music
file. If no music is marked, all the music in the
folder will be played in sequence. When one or
more music files are marked, the marked music
files will be played in sequence. If you want to
listen to only one song repeatedly, just mark
that one file and play.
■
The play information box (as shown below) will automatically
move across the screen when there is no user input to prevent a fixed image remaining on the screen for a extended
period of time.
USB
! NOTE
G
G
G
G
G
When music is playing,
is displayed in front of the music play time.
A damaged or corrupted music file that does not play displays 00:00 as the play time.
Music files with copy-protection will not play.
Press E N T E R, A , or R E T U R N button to stop the screen saver.
This TV can not play music files less than 16 Kbytes.
71
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO) CONTROL
This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV.
■ RGB-PC input source use 4:3 or 16:9 aspect ratio.
! NOTE
G
If a fixed image is displayed on the screen for a long time, the image could become imprinted on the
screen and remain visible.
This phenomenon is common to all manufacturers and is not covered by warranty. Although, after watching video that did not fill the screen, any after-image from the black bars will normally dissipate after a few
minutes.
PICTURE CONTROL
PICTURE
Move
PICTURE
Enter
Aspect Ratio : 16:9
Move
Aspect Ratio : 16:9
Picture Mode : Standard
Picture Mode : Standard
• Backlight
80
• Backlight
80
• Contrast
90
• Contrast
90
Set By Program
• Brightness
50
• Brightness
50
4:3
• Sharpness
60
• Sharpness
60
16:9
• Color
60
• Color
60
• Tint
0
R
• Tint
G
E
1 MENU
ENTER
4RETURN
MENU
72
Zoom1
R
Zoom2 G
Just Scan
Select P I C T U R E.
Select A s p e c t R a t i o.
3
ENTER
0
E
■
2
Enter
Select the desired picture format.
Return to the previous menu.
Return to TV viewing.
You can also adjust A s p e c t R a t i o in
the Q - M e n u.
Set by program
Zoom 1
Selects the proper picture proportion to match
the source’s image.
Choose Zoom 1 when you want to view the picture without any alteration. However, the top and
bottom portions of the picture will be cropped.
(4:3
(16:9
4:3)
16:9)
Zoom 2
4:3
Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio.
PICTURE CONTROL
Choose Zoom 2 when you want the picture to be
altered, both vertically extended and cropped.
The picture taking a halfway trade off between
alteration and screen coverage.
Just Scan
16:9
Adjust the picture horizontally, in a linear proportion to fill the entire screen.
Following selection will lead to you view the picture of best quality without loss of original picture in high resolution image.
Notes: If there are noise in original picture, you
can see the noise at the edge.
J u s t S c a n operates only in
DTV/CADTV/Component/HDMI-DTV/DVI-DTV
(720p/1080i/1080p) input source.
73
PICTURE CONTROL
PRESET PICTURE SETTINGS
Picture Mode - Preset
There are factory presets for picture settings available in the user menus. You can use a preset, change each
setting manually, or use the Intelligent Sensor.
PICTURE
Move
Enter
Aspect Ratio : 16:9
Intelligent Sensor
Vivid
Vivid
Picture Mode : Standard
Vivid
Standard
Standard
• Backlight
80
Standard
Cinema
• Contrast
90
Cinema
Sport
Sport
• Brightness
50
Sport
Game
Game
• Sharpness
60
Game
Expert1
Expert1
• Color
60
Expert1
Expert2
Expert2
• Tint
0
R
G
Cinema
Expert2
E
PICTURE CONTROL
37/42/47/52LG50,
32/37/42/47/52LG60,
32/42/47/52LG70,
1 MENU
2
ENTER
3
ENTER
4RETURN
32/37/42LG30,
42/50PG25
Select P I C T U R E.
Select P i c t u r e M o d e.
Select I n t e l l i g e n t S e n s o r (Except
32/37/42LG30, Plasma TV), V i v i d,
S t a n d a r d, C i n e m a /
Cinema
(Only for 50/60PG60) , S p o r t, or
G a m e.
■
■
Return to the previous menu.
■
MENU
74
50/60PG60
Return to TV viewing.
When selecting I n t e l l i g e n t S e n s o r
(Except 32/37/42LG30, Plasma TV),
the most suitable picture is automatically
adjusted according to the surrounding
conditions.
V i v i d, S t a n d a r d, C i n e m a /
C i n e m a, S p o r t, and G a m e Settings are
preset for the optimum picture quality at
the factory and are not adjustable.
You can also adjust P i c t u r e M o d e in
the Q . M e n u.
Color Tone - Preset
Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to
cool to see less intense colors with more blue.
PICTURE
Move
PICTURE
Enter
Move
Enter
E
E
• Brightness
50
• Brightness
50 Color Temperature
• Sharpness
60
• Sharpness
60 Fresh Contrast
Off
• Color
60
60 Fresh Color
G
0 R
Noise Reduction
• Advanced Control
Gamma
• Reset
Black Level
Off
• Tint
0
F
• Color
R
• Tint
G
• Advanced Control
TruMotion Demo
Screen (RGB-PC)
TruMotion Demo
Off
Medium
Low
Eye Care
Off
Real Cinema
Off
TruMotion
High
Close
1 MENU
G
PICTURE CONTROL
• Reset
Screen (RGB-PC)
Medium
Select P I C T U R E.
2
ENTER
Select A d v a n c e d C o n t r o l.
3
ENTER
Select C o l o r T e m p e r a t u r e.
4
Select C o o l, M e d i u m, or W a r m.
5RETURN
MENU
Return to the previous menu.
Return to TV viewing.
75
PICTURE CONTROL
MANUAL PICTURE ADJUSTMENT
Picture Mode - User Mode
Adjust the picture appearance to suit your preference and viewing situations.
P i c t u r e M o d e - I n t e l l i g e n t S e n s o r”.
LCD TV only: This feature is disable in “P
Picture ModeC i n e m a”.
50/60PG60 only: This feature is disable in “P
PICTURE
Move
Enter
Aspect Ratio : 16:9
80
• Contrast
90
• Brightness
50
• Sharpness
60
• Color
60
• Tint
0
• Backlight
80
E
R
G
E
PICTURE CONTROL
1 MENU
Select P I C T U R E.
2
3
ENTER
Select P i c t u r e M o d e.
ENTER
Select V i v i d, S t a n d a r d, C i n e m a, S p o r t, or G a m e.
4
ENTER
5
ENTER
6RETURN
MENU
76
Select B a c k l i g h t (Only LCD TV), C o n t r a s t,
B r i g h t n e s s, S h a r p n e s s, C o l o r, or T i n t.
Make appropriate adjustments.
Return to the previous menu.
Return to TV viewing.
E
• Backlight
E
E
Picture Mode : Standard
Enter
Picture Mode - Expert Control
By segmenting categories, E x p e r t 1 and E x p e r t 2 provide more categories which users can set as they see
fit, offering the optimal picture quality for users.
PICTURE
Move
PICTURE
Enter
Move
Enter
E
Aspect Ratio : 16:9
• Brightness
50
Fresh Contrast
Picture Mode : Standard
• Sharpness
60
Noise Reduction
• Color
60
• Backlight
80
• Contrast
90
• Brightness
50
• Sharpness
60
• Color
• Tint
Sport
• Expert Control
Expert1
• Reset
Expert2
60
0
• Tint
Game
Screen (RGB-PC)
R
G
E
TruMotion Demo
0
F
Gamma
R
Medium
G
Off
Real Cinema
Off
Color Standard
SD
White Balance
Normal
• Method
2 Points
• Red Contrast
50
• Green Contrast
50
• Blue Contrast
50
ENTER
Select P i c t u r e M o d e.
ENTER
Select E x p e r t 1 or E x p e r t 2.
ENTER
Select E x p e r t C o n t r o l.
ENTER
Select your desired menu option.
3
4
PICTURE CONTROL
2
Select P I C T U R E.
G
Off
Black Level
E
1 MENU
Off
5
6
Make appropriate adjustments.
7RETURN
MENU
Return to the previous menu.
Return to TV viewing.
77
PICTURE CONTROL
PICTURE IMPROVEMENT TECHNOLOGY
Fresh Contrast: Optimizes the contrast automatically according to the brightness of the reflection.
Fresh Color: Adjusts the color of the reflection automatically to reproduce as close as possible natural colors.
Noise Reduction: Removes interference up to the point where it does not damage the original picture.
Gamma: High gamma values display whitish images and low gamma values display high contrast images.
PICTURE
Move
PICTURE
Enter
Move
E
E
• Brightness
50
• Brightness
50
• Sharpness
60
• Sharpness
60
Fresh Contrast
• Color
60
• Color
60
Fresh Color
PICTURE CONTROL
• Tint
0
R
• Tint
G
• Advanced Control
TruMotion Demo
0
• Advanced Control
• Reset
Screen (RGB-PC)
• Reset
Screen (RGB-PC)
TruMotion Demo
R
Medium
F
G
Noise Reduction
Off
Gamma
Medium
Black Level
Low
Eye Care
Off
Off
TruMotion
High
Close
2
Select P I C T U R E.
ENTER
Select A d v a n c e d C o n t r o l.
ENTER
Select F r e s h C o n t r a s t, F r e s h C o l o r,
N o i s e R e d u c t i o n, or G a m m a.
3
4
Select your desired options.
5RETURN
MENU
Return to the previous menu.
Return to TV viewing.
Off
Off
Real Cinema
1 MENU
78
Enter
Color Temperature
G
ADVANCED CONTROL - BLACK (DARKNESS) LEVEL
Adjusting the contrast and the brightness of the screen using the black level of the screen.
This feature is disable in DTV and RGB-PC mode.
PICTURE
Move
PICTURE
Enter
Move
Enter
E
E
• Brightness
50
• Brightness
50
Color Temperature
• Sharpness
60
• Sharpness
60
Fresh Contrast
• Color
60
• Color
60
Fresh Color
• Tint
0
R
• Tint
G
0
• Advanced Control
• Advanced Control
• Reset
• Reset
Screen (RGB-PC)
TruMotion Demo
Screen (RGB-PC)
TruMotion Demo
R
Medium
Off
Off
G
Noise Reduction
Auto
Gamma
Black Level
Medium
F
Eye Care
Low
G
Off
Real Cinema
Off
High
Close
1 MENU
Select P I C T U R E.
■
2
ENTER
Select A d v a n c e d C o n t r o l.
3
■
■
ENTER
Select B l a c k L e v e l.
L o w: The reflection of the screen gets
darker.
H i g h: The reflection of the screen gets
brighter.
A u t o: Realizing the black level of the
screen and set it to High or Low automatically.
PICTURE CONTROL
TruMotion
4
Select L o w or H i g h.
5RETURN
MENU
Return to the previous menu.
Return to TV viewing.
79
PICTURE CONTROL
ADVANCED CONTROL - EYE CARE - LCD TV Only
Dims extremely bright pictures.
P i c t u r e M o d e - V i v i d, C i n e m a”.
This feature is disable in “P
PICTURE
Move
PICTURE
Enter
Move
E
E
• Brightness
50
• Brightness
50
Off
Off
• Sharpness
60
• Sharpness
60
Fresh Contrast
• Color
60
• Color
60
Fresh Color
• Tint
0
R
• Tint
G
• Advanced Control
Screen (RGB-PC)
TruMotion Demo
0
R
Medium
G
Noise Reduction
Off
• Advanced Control Gamma
• Reset
Black Level
• Reset
Screen (RGB-PC)
TruMotion Demo
Eye Care
Medium
Low
F
PICTURE CONTROL
1 MENU
Select P I C T U R E.
ENTER
Select A d v a n c e d C o n t r o l.
ENTER
Select E y e C a r e.
3
4
Select O n or O f f.
5RETURN
MENU
Return to the previous menu.
Return to TV viewing.
Off
Real Cinema
Auto
TruMotion
High
Close
2
80
Enter
Color Temperature
G
ADVANCED CONTROL - REAL CINEMA / FILM MODE
Set up the TV for the best picture appearance for viewing movies.
When you operate Real Cinema/Film Mode (3:2 Pull-Down Mode or Cinema Correction Mode), the TV will
adjust 24 fps video from movies to 30 fps video for display.
■ Plasma TV, 32/37/42LG30
This feature operates only in TV (Analog TV/CATV, Digital DTV/CADTV), AV1, AV2, Component 480i/1080i,
and HDMI 1080i mode.
■ 37/42/47/52LG50
This feature operates only in TV (Analog TV/CATV, Digital DTV/CADTV), AV1, AV2, Component 480i/1080i,
and HDMI 1080i mode.
This TV ouputs 48Hz in DTV, Component, and HDMI 1080p (24Hz).
■ 32/37/42/47/52LG60, 32/42/47/52LG70
This function works with all inputs except PC mode.
TruMotion
Real Cinema
5:5 Pull-Down
Off
On
3:2 Pull-Down
On
On
PICTURE
Move
PICTURE
Enter
Move
PICTURE CONTROL
Screen
Enter
E
E
• Brightness
50
• Brightness
50
Color Temperature
• Sharpness
60
• Sharpness
60
Fresh Contrast
Off
Fresh Contrast
Off
• Color
60
• Color
60
Fresh Color
Off
Fresh Color
Off
Off
Noise Reduction
• Tint
0
R
• Tint
G
• Advanced Control
0
• Reset
Gamma
Film Mode
TruMotion Demo
Off
Off
Medium
Black Level
Low
F
Medium
Gamma
Medium
Black Level
Screen (RGB-PC)
TruMotion Demo
G
Noise Reduction
• Advanced Control
• Reset
Screen (RGB-PC)
R
Color Temperature
Medium
G
Off
Real Cinema
Close
Low
Eye Care
F
TruMotion
For Plasma TV
Off
G
High
Close
For LCD TV
1 MENU
2
ENTER
3
ENTER
Select P I C T U R E.
4
Select A d v a n c e d C o n t r o l.
5RETURN
Select R e a l C i n e m a or F i l m
M o d e.
Select O n or O f f.
MENU
Return to the previous menu.
Return to TV viewing.
81
PICTURE CONTROL
ADVANCED CONTROL - TRUMOTION
- Only 32/37/42/47/52LG60, 32/42/47/52LG70
TruMotion provides even better quality for movies than 3:2 Pull-Down conversions.
TruMotion means the panel supports faster frame rates that normal panels which makes for smoother motion
in video. TruMotion LCD models support 120Hz instead of 60Hz. This means twice the information on the
screen in the same amount of time and easier film conversions (120 is equally divisible by 24, so no interpretations or double frames are needed).
TruMotion works with all inputs except PC mode.
PICTURE
Move
PICTURE
Enter
Move
E
E
• Brightness
50
• Brightness
• Sharpness
60
• Sharpness
• Color
60
• Tint
Enter
0
R
G
• Advanced Control
PICTURE CONTROL
• Reset
Screen (RGB-PC)
TruMotion Demo
50 Color Temperature
Medium
60 Fresh Contrast
• Color
60
Fresh Color
G
• Tint
0 R
Noise Reduction
• Advanced Control
Gamma
• Reset
Black Level
Screen (RGB-PC)
TruMotion Demo
Off
Off
Off
Medium
Low
Eye Care
Off
Real Cinema
TruMotion
Off
F
High
G
Close
1 MENU
2
Select P I C T U R E.
ENTER
Select A d v a n c e d C o n t r o l.
ENTER
Select T r u M o t i o n.
3
4
■
Select O f f, L o w, or H i g h.
5RETURN
MENU
82
■
■
Return to the previous menu.
Return to TV viewing.
■
H i g h: Provides smoother picture movement.
L o w: Provides smooth picture movement.
Use this setting for standard use.
O f f: Use this setting when “High”and
“Low” setting result in noise.
If you enable "TruMotion", noise may
appear on the screen.
If this occurs, set "TruMotion" to "Off".
TRUMOTION DEMO - Only 32/37/42/47/52LG60, 32/42/47/52LG70
Use this feature to see the difference TruMotion makes.
TruMotion works with all inputs except PC mode.
PICTURE
Move
Enter
E
• Brightness
50
• Sharpness
60
• Color
60
• Tint
0
R
G
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion On
TruMotion Off
TruMotion Demo
2
3
ENTER
ENTER
4 MENU
Select P I C T U R E.
PICTURE CONTROL
1 MENU
Select T r u M o t i o n D e m o.
Begin T r u M o t i o n D e m o.
Stop T r u M o t i o n D e m o.
83
PICTURE CONTROL
PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
PICTURE
Move
PICTURE
Enter
Move
E
E
• Brightness
50
• Brightness
50
• Sharpness
60
• Sharpness
60
• Color
60
• Color
60
• Tint
0
R
• Tint
G
0 R
Resetting video configuration...
• Advanced Control
G
• Advanced Control
PICTURE CONTROL
• Reset
1 MENU
2
ENTER
4 MENU
84
• Reset
Screen (RGB-PC)
Screen (RGB-PC)
TruMotion Demo
TruMotion Demo
Select P I C T U R E.
Select R e s e t.
3
ENTER
Initialize the adjusted value.
Return to TV viewing.
Enter
i
POWER INDICATOR - LCD TV Only
OPTION
Language
Move
Enter
: English
OPTION
Language
Enter
Input Label
Input Label
SIMPLINK
: On
SIMPLINK
Key Lock
: Off
Key Lock
Caption
: Off
Caption
Set ID
:1
Set ID
Power Indicator
Power Indicator
Initial Setting
Move
: English
: Home
Initial Setting
: On
: Off
: Off Sound
Srartup
:1
Standby Light
F
Low
Off
Power
Light
: Home
On
Demo Mode
Off
G
Only for
32/37/42/47/52LG60
1 MENU
2
Select O P T I O N.
■
ENTER
Select P o w e r I n d i c a t o r.
■
3
ENTER
Select S r a r t u p S o u n d , S t a n d b y
L i g h t, P o w e r L i g h t or D e m o M o d e.
■
4
Select your desired options.
■
5RETURN
MENU
PICTURE CONTROL
Close
S t a r t u p S o u n d: You can turn off the
starting sound of the TV or set the volume.
S t a n d b y L i g h t: You can set the
brightness of the LED on the front side
of the TV during power standby.
P o w e r L i g h t: You can set the the LED
on the front side of the TV to be turned
on or off while watching the TV.
D e m o M o d e: You can set the LED on
the front side of the TV to flash.
Return to the previous menu.
Return to TV viewing.
85
PICTURE CONTROL
IMAGE STICKING MINIMIZATION (ISM) METHOD - Plasma TV Only
A frozen still picture from a PC/video game displayed on the screen for prolonged periods can result in a ghost
image. You can use Orbiter to help prevent image sticking. The other two functions are for removing a ghost
image.
OPTION
Move
Language
OPTION
Enter
: English
SIMPLINK
: On
SIMPLINK
Key Lock
: Off
Key Lock
: Off
Caption
: Off
Caption
: Off
ISM Method
: Normal
ISM Method
: Level 0
Power Saving
:1
Set ID
Power Saving
Set ID
PICTURE CONTROL
3
ENTER
ENTER
4RETURN
MENU
: On
Normal
Orbiter
: Normal
Inversion
: Level 0
White Wash
:1
E
E
2
Enter
: English
Input Label
Input Label
1 MENU
Move
Language
Select O P T I O N.
■
Select I S M M e t h o d.
■
Select N o r m a l , O r b i t e r ,
I n v e r s i o n or W h i t e W a s h .
■
Return to the previous menu.
■
Return to TV viewing.
N o r m a l: If image sticking is never a
problem, ISM is not necessary - set to
Normal.
O r b i t e r : Orbiter may help prevent
ghost images. However, it is best not to
allow any fixed image to remain on the
screen. To avoid a ghost image on the
screen, the image will move every 2 minutes.
I n v e r s i o n: Inversion will automatically
invert the plasma display panel color
every 30 minutes.
W h i t e W a s h : White Wash removes
ghost images from the screen. Use sparingly. Watch the TV normally for a while
before using this feature to see if the
ghost image disappears on its own.
! NOTE
G
86
An excessive ghosted image may be impossible to
clear entirely with White Wash. To return to normal viewing, press the any button.
POWER SAVING PICTURE MODE - Plasma TV Only
It reduces the plasma display’s power consumption.
OPTION
Move
Language
Enter
: English
Input Label
OPTION
Move
Language
Input Label
SIMPLINK
: On
SIMPLINK
Key Lock
: Off
Key Lock
: Off
Caption
: Off
Caption
: Off
ISM Method
: Normal
ISM Method
Power Saving
: Level 0
Power Saving
Set ID
:1
Set ID
: On
2
3
Select P o w e r S a v i n g.
ENTER
Select L e v e l 0, L e v e l 1,
L e v e l 2, L e v e l 3, or L e v e l 4.
1
2
3
4
Return to the previous menu.
■
MENU
Level
: Normal
Level
: Level 0
Level
:1
Level
Select O P T I O N.
ENTER
4RETURN
Level 0
PICTURE CONTROL
E
E
1 MENU
Enter
: English
Return to TV viewing.
■
■
Level 0 is the brightest.
Level 0 > Level 1 > Level 2 > Level 3 >
Level 4
You can also adjust P o w e r S a v i n g in
the Q . M e n u.
87
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER (AUTO VOLUME)
Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a
regular TV program.
AUDIO
Move
: Off
Auto Volume
: On
Clear Voice
: On
Clear Voice
: On
0
Sound Mode
L
: Standard
SOUND & LANGUAGE CONTROL
4RETURN
MENU
88
On
Balance
0
L
: Standard
• SRS TruSurround XT: Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
Select A U D I O.
Select A u t o V o l u m e.
3
ENTER
Enter
Off
• SRS TruSurround XT: Off
E
ENTER
R
Sound Mode
• Reset
2
Move
Auto Volume
Balance
1 MENU
AUDIO
Enter
Select O n or O f f.
Return to the previous menu.
Return to TV viewing.
• Reset
E
R
PRESET SOUND SETTINGS (SOUND MODE)
Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate
sound options based on the program content.
S t a n d a r d, M u s i c, C i n e m a, S p o r t, and G a m e are preset for optimum sound quality at the factory and are
not adjustable.
AUDIO
Move
Auto Volume
: Off
Clear Voice
: On
Balance
0
Sound Mode
AUDIO
Enter
L
R
: Standard
Move
Auto Volume
: Off
Clear Voice
: On
Balance
0
Sound Mode
•
• Treble
50
•
• Bass
50
•
•
E
2
ENTER
E
Select A U D I O.
Select S o u n d M o d e.
■
3
ENTER
4RETURN
MENU
Standard
SRS TruSurround XT: Off
Music
Treble
50
Cinema
Bass
50
Sport
Reset
Game
You can also adjust S o u n d M o d e in
the Q . M e n u.
SOUND & LANGUAGE CONTROL
1 MENU
R
: Standard
• SRS TruSurround XT: Off
• Reset
L
Enter
Select S t a n d a r d, M u s i c,
C i n e m a, S p o r t, or G a m e.
Return to the previous menu.
Return to TV viewing.
89
SOUND & LANGUAGE CONTROL
SOUND SETTING ADJUSTMENT - USER MODE
Adjust the sound to suit your taste and room situations.
Move
Enter
AUDIO
Move
Auto Volume
: Off
Auto Volume
: Off
Clear Voice
: On
Clear Voice
: On
Balance
0
Sound Mode
L
R
: Standard
Balance
Sound Mode
0
Enter
L
R
: Standard
• SRS TruSurround XT: Off
• Treble
50
• Treble
50
SRS TruSurround XT
• Bass
50
• Bass
50
Treble
50
Bass
50
• Reset
• Reset
E
E
E
• SRS TruSurround XT: Off
Off
E
AUDIO
Close
1 MENU
2
SOUND & LANGUAGE CONTROL
3
ENTER
5
Select S o u n d M o d e.
6RETURN
ENTER
Select S t a n d a r d, M u s i c,
C i n e m a, S p o r t, or G a m e.
ENTER
Select T r e b l e or B a s s.
4
ENTER
MENU
Make appropriate adjustments.
Return to the previous menu.
Return to TV viewing.
SRS TRUSURROUND XT
1 MENU
2
Select A U D I O.
ENTER
Select S R S T r u S u r r o u n d X T
ENTER
Select O n or O f f.
3
4RETURN
MENU
90
Select A U D I O.
Return to the previous menu.
Return to TV viewing.
■
S R S T r u S u r r o u n d X T: Takes advantage of
any multi-channel format without needing to
add extra speakers or equipment. Dialog clarity,
bass enrichment, and the addition of stereo
audio enhancement produces an immersive
sound experience from standard stereo material.
CLEAR VOICE
By differentiating the human sound range from others, it improves the sound quality of voices.
AUDIO
Move
Auto Volume
: Off
Clear Voice
: On
Balance
0
Sound Mode
AUDIO
Enter
L
: Standard
R
Move
Auto Volume
: Off
Clear Voice
: On
0
On
R
: Standard
• SRS TruSurround XT: Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
E
E
Select A U D I O.
ENTER
Select C l e a r V o i c e.
ENTER
Select O n or O f f.
3
4RETURN
MENU
Return to the previous menu.
Return to TV viewing.
■
■
C l e a r V o i c e - O n”, S R S
If you select “C
T r u S u r r o u n d X T feature will not
work.
You can also adjust C l e a r V o i c e in the
Q - M e n u.
SOUND & LANGUAGE CONTROL
2
L
• SRS TruSurround XT: Off
• Reset
1 MENU
Off
Balance
Sound Mode
Enter
91
SOUND & LANGUAGE CONTROL
BALANCE
Adjust the left/right sound of speaker to suit your taste and room situations.
Move
Auto Volume
: Off
Clear Voice
: On
0
Sound Mode
L
R
: Standard
SOUND & LANGUAGE CONTROL
ENTER
4RETURN
MENU
92
Clear Voice
: On
Balance
0
L
Balance
• SRS TruSurround XT: Off
50
• Treble
50
• Bass
50
• Bass
50
Select A U D I O.
Select B a l a n c e.
Make appropriate adjustments.
Return to the previous menu.
Return to TV viewing.
Enter
R
0
: Standard
• Treble
3
ENTER
: Off
• SRS TruSurround XT: Off
E
2
Move
Auto Volume
Sound Mode
• Reset
1 MENU
AUDIO
E
Balance
Enter
• Reset
E
Close
L
R
E
AUDIO
TV SPEAKERS ON/OFF SETUP
Turn the TV speakers off if using external audio equipment.
AUDIO
Move
Enter
AUDIO
Move
E
E
Clear Voice
: On
Balance
Clear Voice
0
Sound Mode
L
: Standard
R
: On
Balance
Sound Mode
0
L
R
: Standard
• SRS TruSurround XT: Off
• SRS TruSurround XT: Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
TV Speaker
Enter
: On
• Reset
TV Speaker
: On
Off
On
2
Select A U D I O.
ENTER
Select T V S p e a k e r.
ENTER
Select O n or O f f.
3
4RETURN
MENU
SOUND & LANGUAGE CONTROL
1 MENU
Return to the previous menu.
Return to TV viewing.
93
SOUND & LANGUAGE CONTROL
AUDIO RESET
Settings of the selected Sound Mode return to the default factory settings.
AUDIO
Move
Auto Volume
: Off
Clear Voice
: On
Balance
Sound Mode
0
L
: Standard
SOUND & LANGUAGE CONTROL
ENTER
4 MENU
94
: Off
Clear Voice
: On
Balance
0
L
• SRS TruSurround XT: Off
50
• Treble
50
• Bass
50
• Bass
50
Select A U D I O.
Select R e s e t.
Initialize the adjusted value.
Return to TV viewing.
Enter
R
: Standard
i Resetting audio configuration...
• Treble
3
ENTER
Move
Auto Volume
• SRS TruSurround XT: Off
E
2
R
AUDIO
Sound Mode
• Reset
1 MENU
Enter
• Reset
E
STEREO/SAP BROADCAST SETUP
For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used
if the broadcast is only in Mono.
Plasma TV
LCD TV
Q.Menu
Q.Menu
Aspect Ratio
Power Saving
Vivid
Picture Mode
Vivid
Sound Mode
Standard
Sound Mode
Standard
Off
Multi Audio
F
English
Multi Audio
Add
USB Eject
Eject
CH
English
G
Off
Sleep Timer
Del/Add/Fav
Add
USB Eject
Eject
Close
Analog TV
F
Close
Digital TV
Select S A P.
Select M o n o, S t e r e o, or S A P.
3Q. MENU
Return to TV viewing.
1Q. MENU
2
Select M u l t i A u d i o.
Select other languages.
SOUND & LANGUAGE CONTROL
Del/Add/Fav
Off
Caption
G
Off
Sleep Timer
2
3
Off
Clear Voice
Picture Mode
Caption
1Q. MENU
16:9
Backlight
3
Off
Clear Voice
CH
Aspect Ratio
16:9
3Q. MENU
Return to TV viewing.
95
SOUND & LANGUAGE CONTROL
AUDIO LANGUAGE
Other languages may be available if a digital signal is provided by the broadcasting station.
This feature operates only in DTV/CADTV mode.
OPTION
Move
Language
Enter
: English
Input Label
SIMPLINK
: On
: Off
Key Lock
: Off
Caption
: Off
Caption
: Off
ISM Method
: Normal
ISM Method
: Normal
: Level 0
Power Saving
: Level 0
:1
Set ID
SOUND & LANGUAGE CONTROL
Select O P T I O N.
Select L a n g u a g e.
ENTER
Select A u d i o.
4
Select your desired language:
E n g l i s h, S p a n i s h, or F r e n c h
MENU
96
Audio
: On
ENTER
5RETURN
: English
Menu
Key Lock
E
3
Language
Enter
SIMPLINK
Set ID
2
Move
Input Label
Power Saving
1 MENU
OPTION
Return to the previous menu.
Return to TV viewing.
:1
E
English
F
English
Close
G
ON-SCREEN MENUS LANGUAGE SELECTION
The menus can be shown on the screen in the selected language.
OPTION
Move
Language
Enter
: English
Input Label
Audio
SIMPLINK
: On
SIMPLINK
Key Lock
: Off
Key Lock
: Off
Caption
: Off
Caption
: Off
ISM Method
: Normal
ISM Method
: Normal
Power Saving
: Level 0
Power Saving
: Level 0
Set ID
:1
Set ID
Select O P T I O N.
ENTER
Select L a n g u a g e.
ENTER
Select M e n u.
3
4
Enter
: English
Menu
F
English
G
English
: On
Close
:1
E
SOUND & LANGUAGE CONTROL
2
Move
Language
Input Label
E
1 MENU
OPTION
Select your desired language.
From this point on, the on-screen menus
will be shown in the selected language.
5RETURN
MENU
Return to the previous menu.
Return to TV viewing.
97
SOUND & LANGUAGE CONTROL
CAPTION MODE
Analog Broadcasting System Captions
Caption must be provided to help people with hearing loss watch TV. Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen
and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both
digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode
which was last set when you turned the power off. This function is only available when C a p t i o n Mode is set O n.
OPTION
Move
Language
Enter
: English
Input Label
Move
Language
Enter
: English
Input Label
SOUND & LANGUAGE CONTROL
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Caption
: Off
Caption
: CC1
ISM Method
: Normal
ISM Method
: Normal
Power Saving
: Level 0
Power Saving
: Level 0
Set ID
:1
Set ID
:1
E
F
Mode
On
G
CC1
Digital Option
E
Close
1 MENU
2
Select O P T I O N.
■
ENTER
Select C a p t i o n.
■
ENTER
Select O n.
3
■
4
4 or T e x t 1-4
4.
Select C C 1-4
5RETURN
MENU
98
OPTION
Return to the previous menu.
Return to TV viewing.
When selecting O f f, Sub-menus for
Analog, DTV, and Digital Option
become disabled.
CAPTION
The term for the words that scroll
across the bottom of the TV screen;
usually the audio portion of the program provided for the hearing impaired.
TEXT
The term for the words that appear in a
large black frame and almost cover the
entire screen; usually messages provided by the broadcaster.
Digital Broadcasting System Captions
Choose the language you want the DTV/CADTV Captions to appear in.
Other Languages can be chosen for digital sources only if they are included on the program.
This function in only available when Caption Mode is set On.
OPTION
Move
Language
Enter
: English
Input Label
Input Label
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Caption
: Off
Caption
: CC1
ISM Method
: Normal
ISM Method
Mode
: Normal
Power Saving
: Level 0
Power Saving
: Level 0
Set ID
:1
Set ID
:1
Select O P T I O N.
ENTER
Select C a p t i o n.
ENTER
Select O n.
3
4
4 , T e x t 1-4
4 , or
Select C C 1-4
S e r v i c e 1 - 6.
5RETURN
MENU
Enter
: English
E
F
On
G
CC1
Digital Option
Close
SOUND & LANGUAGE CONTROL
2
Move
Language
SIMPLINK
E
1 MENU
OPTION
Return to the previous menu.
Return to TV viewing.
99
SOUND & LANGUAGE CONTROL
Caption Option
Customize the DTV/CADTV captions that appear on your screen.
This function in only available when Caption Mode is set On.
F
OPTION
Move
Language
Enter
: English
Input Label
Move
Language
Enter
: English
Input Label
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
F
On
G
Caption
: Off
Caption
ISM Method
: Normal
ISM Method
: CC1
Mode
: Normal
Power Saving
: Level 0
Power Saving
: Level 0 Digital Option
Set ID
:1
Set ID
:1
E
SOUND & LANGUAGE CONTROL
1 MENU
E
Service1
Close
2
■
ENTER
Select C a p t i o n
ENTER
Select O n.
3
■
■
■
4
Select D i g i t a l O p t i o n.
5
6
Select C u s t o m.
Customize the S t y l e, F o n t, etc., to your
preference. A preview icon is provided at
the bottom of the screen, use it to see the
caption language.
7RETURN
MENU
G
A Standard
Font
Font 1
Text Color
White
Text Opacity
Solid
Bg Color
Black
Bg Opacity
Solid
Edge Type
None
Edge Color
Black
Close
Select O P T I O N.
■
ENTER
100
OPTION
Custom
Size
Return to the previous menu.
Return to TV viewing.
■
■
■
S i z e: Set the word size.
F o n t: Select a typeface for the text.
T e x t C o l o r: Choose a color for the
text.
T e x t O p a c i t y: Specify the opacity
for the text color.
B g ( B a c k g r o u n d ) C o l o r: Select a
background color.
B g ( B a c k g r o u n d ) O p a c i t y: Select
the opacity for the background color.
E d g e T y p e: Select an edge type.
E d g e C o l o r: Select a color for the
edges.
TIME SETTING
CLOCK SETTING
Auto Clock Setup
The time is set automatically from a digital channel signal.
The digital channel signal includes information for the current time provided by the broadcasting station.
Set the clock manually if the current time is set incorrectly by the auto clock function.
TIME
Move
Enter
TIME
Move
Enter
Clock
: Feb/21/2008 2:10 AM
Clock
: Feb/21/2008 2:10 AMF
Off Time
: Off
Off Time
: Off
On Time
: Off
On Time
: Off
Sleep Timer : Off
Sleep Timer : Off
Auto Sleep : Off
Auto Sleep : Off
Auto
Year
G
2008
Month
2
Date
21
Hour
2 AM
Minute
10
Eastern
Time Zone
Daylight
Saving
Auto
Close
1 MENU
ENTER
Select C l o c k.
ENTER
Select A u t o.
3
4
TIME SETTING
2
Select T I M E.
Select your viewing area time zone.
• U.S.A: E a s t e r n , C e n t r a l , M o u n t a i n ,
P a c i f i c, A l a s k a, or H a w a i i.
• Canada: E a s t e r n, C e n t r a l, M o u n t a i n,
P a c i f i c, N e w F . l a n d, or A t l a n t i c.
5
Select A u t o, O f f, or O n (depending on
whether or not your viewing area observes
Daylight Saving time).
6RETURN
MENU
Return to the previous menu.
Return to TV viewing.
101
TIME SETTING
Manual Clock Setup
If the current time setting is wrong, set the clock manually.
TIME
Move
Enter
TIME
Move
Enter
Clock
: Feb/21/2008 2:10 AM
Clock
: Feb/21/2008 2:10 AM F
Off Time
: Off
Off Time
: Off
On Time
: Off
On Time
: Off
Sleep Timer : Off
Sleep Timer : Off
Auto Sleep : Off
Auto Sleep : Off
Manual
Year
Month
2
Date
21
Hour
2 AM
Minute
10
Eastern
Time Zone
Daylight
Saving
Auto
Close
1 MENU
2
TIME SETTING
ENTER
Select C l o c k.
ENTER
Select M a n u a l.
3
4
Select the Year, Month, Date, Hour, or Minutes
option.
5
Set the Year, Month, Date, Hour, or Minutes
option.
6RETURN
MENU
102
Select T I M E.
Return to the previous menu.
Return to TV viewing.
G
2008
AUTO ON/OFF TIME SETTING
This function operates only if the current time has been set.
The O f f T i m e function overrides the O n T i m e function if they are both set to the same time.
The TV must be in standby mode for the O n T i m e to work.
If you do not press any button within 2 hours after the TV turns on with the O n T i m e function, the TV will
automatically revert to standby mode.
TIME
Move
TIME
Enter
Move
Enter
Clock
: Feb/21/2008 2:10 AM
Clock
: Feb/21/2008 2:10 AM
Off Time
: Off
Off Time
: Off
On Time
: Off
On Time
Repeat
: 6:30 AM (Once)
Sleep Timer : Off Hour
Auto Sleep : Off Minute
Sleep Timer : Off
Auto Sleep : Off
F
Once
G
6 AM
30
Input
TV
Channel
TV 2-0
Volume
30
Close
1 MENU
Select T I M E.
■
■
ENTER
Select O f f t i m e or O n t i m e.
ENTER
Select R e p e a t.
1
2
3
4
Select O f f, O n c e, E v e r y d a y, M o n~FF r i,
M o n~S
S a t, W e e k e n d, or S u n d a y.
5
Select and set H o u r or M i n u t e.
6RETURN
MENU
3
4
ENTER
Select I n p u t.
Select T V, AV/AV1-2, Component1-2,
R G B - P C, or H D M I 1 - 4.
TIME SETTING
2
To cancel O n / O f f T i m e function, select O f f.
Only for On Time function
When Selecting T V:
set the channel at turn-on.
Adjust to sound level at
turn-on.
Return to the previous menu.
Return to TV viewing.
103
TIME SETTING
SLEEP TIMER SETTING
The Sleep Timer turns the TV off at the preset time.
Note that this setting is cleared when the TV is turned off.
TIME
Clock
1 MENU
2
ENTER
TIME SETTING
3
Enter
TIME
ENTER
4RETURN
Move
Clock
Off Time
: Off
Off Time
: Off
On Time
: Off
On Time
: Off
Enter
: Feb/21/2008 2:10 AM
Sleep Timer : Off
Sleep Timer : Off
Auto Sleep : Off
Auto Sleep : Off
F
Off
G
Close
Select T I M E.
Select S l e e p T i m e r.
■
MENU
104
Move
: Feb/21/2008 2:10 AM
Select O f f, 1 0, 2 0, 3 0, 6 0, 9 0,
1 2 0, 1 8 0, or 2 4 0 minutes.
Return to the previous menu.
Return to TV viewing.
You can also adjust S l e e p T i m e r in
the Q - M e n u.
AUTO SHUT-OFF SETTING
TV will be automatically turned off, in case of no signal for 10 minutes.
TIME
Clock
Move
Enter
TIME
Move
Enter
: Feb/21/2008 2:10 AM
Clock
: Feb/21/2008 2:10 AM
Off Time
: Off
Off Time
: Off
On Time
: Off
On Time
: Off
Sleep Timer : Off
Sleep Timer : Off
Auto Sleep : Off
Auto Sleep : On
Off
On
TV will be automatically turned off,
in case of No Signal for 10 minutes.
1 MENU
2
ENTER
Select T I M E.
Select A u t o S l e e p.
ENTER
4RETURN
MENU
Select O n or O f f.
Return to the previous menu.
TIME SETTING
3
Return to TV viewing.
105
PARENTAL CONTROL / RATINGS
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the
type of the program and the categories. It is also possible to block all program viewing for a time period. To use
this function, the following must be done :
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enable the lock
V-Chip rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be
blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-tovideo movies use the Movie Rating System (MPAA) only.
Ratings for Television programs including made-for-TV movies :
TV-G
■ TV-PG
■ TV-14
■
(General audience)
(Parental guidance suggested)
(Parents strongly cautioned)
TV-MA (Mature audience only)
(All children)
■ TV-Y
■ TV-Y7 (Children 7 years older)
■
SET PASSWORD & LOCK SYSTEM
PARENTAL CONTROL / RATING
Setting up Your Password
Set up blocking schemes to block specific channels, ratings, and external viewing sources.
A password is required to gain access to this menu.
For USA
LOCK
Move
Lock System
For Canada
Enter
: Off
LOCK
Lock System
Move
Enter
: Off
Set Password
Set Password
Block Channel
Block Channel
Movie Rating
TV Rating-English
TV Rating-Children
TV Rating-French
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Enter Password
*
*
*
*
Close
Input Block
1 MENU
ENTER
Select L O C K.
■
■
2
1
2
3
4
5
6
7
8
9
0
106
Input the password.
Enter the password as requested.
The TV is set up with the initial password “0-0-0-0”.
Lock System
Enables or disables the blocking scheme you set up previously.
LOCK
Move
Lock System
1 MENU
2
1
2
3
4
5
6
8
9
7
Enter
: Off
LOCK
Move
Lock System
: On
Set Password
Set Password
Block Channel
Block Channel
Movie Rating
Movie Rating
TV Rating-Children
TV Rating-Children
TV Rating-General
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Input Block
ENTER
Enter
Off
On
Select L O C K.
Input the password.
0
Select L o c k S y s t e m.
4
ENTER
5RETURN
MENU
Select O n or O f f.
Return to the previous menu.
Return to TV viewing.
■
When you select O n, the Lock System
is enable.
PARENTAL CONTROL / RATING
3
107
PARENTAL CONTROL / RATINGS
Set Password
Change the password by inputting a new password twice.
LOCK
Move
Lock System
1 MENU
2
1
2
3
4
5
6
7
8
9
Enter
: Off
Set Password
Block Channel
Block Channel
PARENTAL CONTROL / RATING
108
ENTER
Movie Rating
TV Rating-Children
TV Rating-Children
TV Rating-General
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Input Block
ENTER
Select L O C K.
Input the password.
1
2
3
4
5
6
7
8
9
0
5RETURN
MENU
Move
Choose any 4 digits for your new password.
As soon as the 4 digits are entered, re-enter
the same 4 digits on the C o n f i r m.
Return to the previous menu.
Return to TV viewing.
Enter
: Off
Movie Rating
Select S e t p a s s w o r d.
4
Lock System
Set Password
0
3
LOCK
New
*
*
*
*
Confirm
*
*
*
*
Close
CHANNEL BLOCKING
Blocks any channels that you do not want to watch or that you do not want your children to watch.
LOCK
Move
Lock System
Enter
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
1 MENU
2
1
2
3
4
5
6
7
8
9
Block/Unblock
ENTER
Move
CH
Move Page
MENU Previous
RETURN Exit
Select L O C K.
Input the password.
0
Select B l o c k C h a n n e l.
4
ENTER
Select a channel to block or unblock.
5
ENTER
6 MENU
RETURN
Block or unblock a channel.
Return to the previous menu.
PARENTAL CONTROL / RATING
3
Return to TV viewing.
109
PARENTAL CONTROL / RATINGS
MOVIE & TV RATING
Movie Rating (MPAA) - For USA only
Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can
set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that
the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
LOCK
Move
Enter
LOCK
Move
Enter
Blocking off : Permits all programs
Lock System
1 MENU
2
1
2
3
4
5
6
8
9
7
: Off
Set Password
Block Channel
Block Channel
Movie Rating
Movie Rating
TV Rating-Children
TV Rating-Children
TV Rating-General
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Input Block
ENTER
PARENTAL CONTROL / RATING
110
ENTER
5RETURN
MENU
G
PG
PG-13
R
NC-17
X
Blocking Off
Select L O C K.
Input the password.
Select M o v i e R a t i n g.
4
: Off
Set Password
0
3
Lock System
Select G , P G, P G - 1 3, R , N C - 1 7,
X , or B l o c k i n g O f f.
Return to the previous menu.
Return to TV viewing.
G (General audience)
■ PG (Parental guidance suggested)
■ PG-13 (Parents strongly cautioned)
■ R (Restricted)
■ NC-17 (No one 17 and under admitted)
■ X (Adult only)
■ Blocking Off (Permits all programs)
G If you set PG-13: G and PG movies will
be available, PG-13, R, NC-17 and X will
be blocked.
■
TV Rating Children - For USA only
Prevents children from watching certain children's TV programs, according to the ratings limit set. The children
rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.
LOCK
Move
Lock System
1 MENU
2
1
2
3
4
5
6
7
8
9
Enter
: Off
LOCK
Move
Lock System
: Off
Set Password
Set Password
Block Channel
Block Channel
Movie Rating
Movie Rating
TV Rating-Children
TV Rating-Children
TV Rating-General
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Input Block
ENTER
Enter
Age
Fantasy Violence
Close
Select L O C K.
Input the password.
0
Select T V R a t i n g - C h i l d r e n.
4
■
ENTER
Select A g e or F a n t a s y V i o l e n c e.
ENTER
Select block options.
5
6RETURN
MENU
Return to the previous menu.
■
Age (applies to TV-Y, TV-Y7)
Fantasy Violence (applies to TV-Y7)
PARENTAL CONTROL / RATING
3
Return to TV viewing.
111
PARENTAL CONTROL / RATINGS
TV Rating General - For USA only
Based on the ratings, blocks certain TV programs that you and your family do not want to view.
LOCK
Move
Lock System
Enter
: Off
LOCK
Move
Lock System
Enter
: Off
Set Password
Set Password
Block Channel
Block Channel
Age
Movie Rating
Movie Rating
Dialogue
TV Rating-Children
TV Rating-Children
Language
TV Rating-General
TV Rating-General
Sex
Downloadable Rating
Downloadable Rating
Violence
Input Block
Input Block
Close
1 MENU
2
1
2
3
4
5
6
7
8
9
ENTER
Select L O C K.
Input the password.
0
PARENTAL CONTROL / RATING
3
Select T V R a t i n g - G e n e r a l.
4
■
ENTER
5
■
■
ENTER
Select block options.
■
6RETURN
MENU
112
Select A g e, D i a l o g u e, L a n g u a g e,
S e x or V i o l e n c e.
Return to the previous menu.
Return to TV viewing.
■
Age (applies to TV-G,TV-PG,TV-14,TVMA).
Dialogue-sexual dialogue (applies to
TV-PG,TV-14).
Language-adult language (applies to
TV-PG, TV-14, TV-MA).
Sex-sexual situations (applies to TV-PG,
TV-14, TV-MA).
Violence (applies to TV-PG, TV-14, TVMA).
TV Rating English - For CANADA only
Selecting canadian english language rating system.
LOCK
Move
Enter
Blocking off : Permits all programs
LOCK
Move
Enter
E
Lock System
: Off
Lock System
: Off
Set Password
Set Password
Block Channel
Block Channel
TV Rating-English
TV Rating-English
TV Rating-French
TV Rating-French
Downloadable Rating
Downloadable Rating
Input Block
Input Block
C
C8+
G
PG
14+
18+
Blocking Off
1 MENU
2
1
2
3
4
5
6
8
9
7
ENTER
Select L O C K.
■
Input the password.
■
0
■
3
■
■
4
ENTER
Select E , C , C 8 +, G , P G, 1 4 +,
1 8 +, or B l o c k i n g O f f.
■
■
■
5RETURN
MENU
Return to the previous menu.
Return to TV viewing.
PARENTAL CONTROL / RATING
Select T V R a t i n g - E n g l i s h.
E (Exempt)
C (Children)
C8+ (Children eight years and older)
G (General programming, suitable for
all audiences)
PG (Parental Guidance)
14+ (Viewers 14 years and older)
18+ (Adult programming)
Blocking Off (Permits all programs)
113
PARENTAL CONTROL / RATINGS
TV Rating French - For CANADA only
Selecting canadian french language rating system.
LOCK
Move
Lock System
Enter
: Off
LOCK
Move
Lock System
: Off
Enter
Blocking off : Permits all programs
E
Set Password
Set Password
G
Block Channel
Block Channel
8ans+
TV Rating-English
TV Rating-English
13ans+
TV Rating-French
TV Rating-French
16ans+
Downloadable Rating
Downloadable Rating
18ans+
Input Block
Input Block
Blocking Off
1 MENU
2
1
2
3
4
5
6
8
9
7
ENTER
Select L O C K.
■
Input the password.
0
3
PARENTAL CONTROL / RATING
114
■
Select T V R a t i n g - F r e n c h.
4
ENTER
5RETURN
MENU
■
Select E , G , 8 a n s +, 1 3 a n s +,
1 6 a n s +, 1 8 a n s +, or B l o c k i n g o f f.
Return to the previous menu.
Return to TV viewing.
■
■
■
■
E (Exempt)
G (General)
8ans+ (General-Not convenient for little children)
13ans+ (Not convenient for children of
13 years and younger)
16ans+ (Not convenient for children of
16 years and younger)
18ans+ (This programs is only for
adults)
Blocking off (Permits all programs)
DOWNLOADABLE RATING
This function may become available in the future and will be available only for digital channels.
This function operates only when TV has received Region5 Rating data.
Move
Lock System
Enter
: Off
LOCK
Move
Lock System
Enter
: Off
E
LOCK
Set Password
Set Password
Block Channel
Block Channel
Humor
Movie Rating
Movie Rating
Sport
TV Rating-Children
TV Rating-Children
Cruelty
TV Rating-General
TV Rating-General
Language
Downloadable Rating
Downloadable Rating
Sadness
Input Block
Input Block
Genre
Age
E
Close
■
1 MENU
1
2
3
4
5
6
7
8
9
Select L O C K.
Input the password.
0
3
Select D o w n l o a d a b l e R a t i n g.
4
ENTER
Select desired D o w n l o a d a b l e
R a t i n g option.
ENTER
Select desired option and block it.
5
6RETURN
MENU
PARENTAL CONTROL / RATING
2
ENTER
Based on rating table, your TV's OSD
(On Screen Display) may differ slightly
from what is shown in this manual.
Return to the previous menu.
Return to TV viewing.
115
PARENTAL CONTROL / RATINGS
EXTERNAL INPUT BLOCKING
Enables you to block an input.
AV1
LOCK
Move
Enter
F
G
AV1
F
G
AV
AV2
AV2
Component1
Component1
Component1
Component2
Component2
Component2
RGB-PC
RGB-PC
RGB-PC
HDMI1
HDMI1
HDMI1
HDMI2
TV Rating-General
HDMI2
HDMI2
HDMI3
Downloadable Rating
HDMI3
HDMI3
HDMI4
Lock System
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
Input Block
F
G
HDMI4
Close
Close
Close
32/37/42LG30,
37/42/47/52LG50
1 MENU
2
1
2
3
4
5
6
7
8
9
ENTER
Select L O C K.
Input the password.
0
PARENTAL CONTROL / RATING
3
Select I n p u t B l o c k.
4
ENTER
5
Select O n or O f f.
6RETURN
MENU
116
Select input source.
Return to the previous menu.
Return to TV viewing.
32/37/42/47/52LG60
Plasma TV, 32/42/47/52LG70
KEY LOCK
The TV can be set up so that it can only be used with the remote control.
This feature can be used to prevent unauthorized viewing by locking out the front panel controls.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
OPTION
Move
Language
Enter
: English
Input Label
OPTION
Move
Language
Input Label
SIMPLINK
: On
SIMPLINK
Key Lock
: Off
Key Lock
: On
Off
Caption
: Off
Caption
: Off
On
ISM Method
: Normal
ISM Method
: Normal
Power Saving
: Level 0
Power Saving
: Level 0
Set ID
:1
Set ID
: On
:1
E
1 MENU
2
ENTER
E
Select O P T I O N.
3
4RETURN
MENU
Select O n or O f f.
■
Return to the previous menu.
Return to TV viewing.
O n’, if the TV is turned
In K e y L o c k ‘O
off, press the r / I, INPUT, CH (DE or
) button on the TV or POWER,
INPUT, CH
or NUMBER buttons
on the remote control.
With the K e y L o c k O n, the display
‘ ! K e y L o c k’ appears on the screen
if any button on the front panel is
pressed while viewing the TV.
PARENTAL CONTROL / RATING
Select Key Lock.
■
ENTER
Enter
: English
117
APPENDIX
TROUBLESHOOTING
The operation does not work normally.
Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■ Ensure that the correct remote operating mode is set: TV, VCR etc.
■ Install new batteries.
■
The remote control
doesn’t work
Power is suddenly
turned off
Is the sleep timer set?
■ Check the power control settings. Power interrupted.
■
The video function does not work.
Check whether the product is turned on.
■ Try another channel. The problem may be with the broadcast.
■ Is the power cord inserted into wall power outlet?
■ Check your antenna direction and/or location.
■ Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
■
No picture &No sound
Picture appears slowly
after switching on
■
This is normal, the image is muted during the product startup process. Please
contact your service center, if the picture has not appeared after five minutes.
Adjust Color in menu option.
Keep a sufficient distance between the product and the VCR.
■ Try another channel. The problem may be with the broadcast.
■ Are the video cables installed properly?
■ Activate any function to restore the brightness of the picture.
■
■
APPENDIX
No or poor color
or poor picture
Horizontal/vertical bars
or picture shaking
■
Check for local interference such as an electrical appliance or power tool.
Station or cable product experiencing problems, tune to another station.
Station signal is weak, reorient antenna to receive weaker station.
■ Check for sources of possible interference.
■
Poor reception on
some channels
Lines or streaks
in pictures
No picture
when connecting HDMI
118
■
■
Check antenna (Change the direction of the antenna).
■
Check HDMI cable over version 1.3.
The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screen
display. In this case use the latest cables that support HDMI version 1.3.
The audio function does not work.
Press the VOL or VOLUME button.
■ Sound muted? Press MUTE button.
■ Try another channel. The problem may be with the broadcast.
■ Are the audio cables installed properly?
■
Picture OK & No sound
No output from one
of the speakers
■
Adjust Balance in menu option.
■
A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the
product.
Unusual sound from
inside the product
No sound
when connecting
HDMI/USB
Check HDMI cable over version 1.3.
■ Check USB cable over version 2.0.
■ Use normal MP3 file.
■
There is a problem in PC mode. (Only PC mode applied)
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
Screen color is unstable
or single color
Adjust resolution, horizontal frequency, or vertical frequency.
■ Check the input source.
■
■
APPENDIX
The signal is out of range
Work the Auto configure or adjust clock, phase, or H/V position. (Option)
Check the signal cable.
■ Reinstall the PC video card.
■
119
APPENDIX
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new TV.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then
use it to wipe the screen.
1
2
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■ Please be sure not to use a wet cloth.
■
Extended Absence
CAUTION
G
APPENDIX
120
If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.
PRODUCT SPECIFICATIONS
MODELS
Dimensions
(Width x Height
x Depth)
With stand
Weight
With stand
Without stand
Without stand
MODELS
Dimensions
(Width x Height
x Depth)
With stand
Weight
With stand
Without stand
Without stand
MODELS
Dimensions
(Width x Height
x Depth)
With stand
Weight
With stand
Without stand
Without stand
Environment
condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
■
31.5 x 23.7 x 8.9 inches
801.8 x 604.2 x 227.3 mm
31.5 x 21.4 x 3.1 inches
801.8 x 544.1 x 79.0 mm
29.5 pounds / 13.4 kg
26.2 pounds / 11.9 kg
37LG30
(37LG30-UA)
(37LG30-UD)
42LG30
(42LG30-UA)
(42LG30-UD)
36.2 x 26.8 x 11.5 inches 40.6 x 29.2 x 11.5 inches
919.6 x 682.3 x 293.8 mm 1032.8 x 742.3 x 293.8 mm
36.2 x 24.0 x 3.5 inches 40.6 x 26.3 x 3.6 inches
919.6 x 610.3 x 89.0 mm 1032.8 x 670.1 x 92.0 mm
41.4 pounds / 18.8 kg
35.7 pounds / 16.2 kg
52.0 pounds / 23.6 kg
46.2 pounds / 21.0 kg
37LG50
(37LG50-UA)
(37LG50-UG)
36.8 x 26.9 x 11.5 inches
936.4 x 685.4 x 293.4 mm
36.8 x 24.1 x 3.4 inches
936.4 x 612.8 x 88.0 mm
42LG50
(42LG50-UA)
(42LG50-UG)
40.7 x 28.9 x 11.5 inches
1034.0 x 735.0 x 294.0 mm
40.7 x 26.1 x 3.5 inches
1034.0 x 663.0 x 91.0 mm
40.3 pounds / 18.3 kg
34.3 pounds / 15.6 kg
54.0 pounds / 24.5 kg
48.5 pounds / 22.0 kg
47LG50
(47LG50-UA)
(47LG50-UG)
45.5 x 32.0 x 13.5 inches
1156.2 x 813.1 x 342.9 mm
45.5 x 29.1 x 4.0 inches
1156.2 x 739.2 x 103.0 mm
52LG50
(52LG50-UA)
(52LG50-UG)
50.8 x 35.1 x 13.5 inches
1291.7 x 892.2 x 342.9 mm
50.8 x 32.1 x 4.5 inches
1291.7 x 817.0 x 115.3 mm
64.3 pounds / 29.2 kg
54.2 pounds / 24.6 kg
87.0 pounds / 39.5 kg
76.9 pounds / 34.9 kg
AC100-240V ~ 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
APPENDIX
Power requirement
Television System
Program Coverage
External Antenna Impedance
32LG30
(32LG30-UA)
(32LG30-UD)
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
121
APPENDIX
MODELS
Dimensions
(Width x Height
x Depth)
With stand
Weight
With stand
Without stand
Without stand
MODELS
Dimensions
(Width x Height
x Depth)
With stand
Weight
With stand
Without stand
Without stand
MODELS
Dimensions
(Width x Height
x Depth)
With stand
Weight
With stand
Without stand
Without stand
MODELS
APPENDIX
Dimensions
(Width x Height
x Depth)
With stand
Weight
With stand
Without stand
Without stand
Power requirement
Television System
Program Coverage
External Antenna Impedance
Environment
condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
■
122
32LG60
(32LG60-UA)
37LG60
(37LG60-UA)
42LG60
(42LG60-UA)
31.7 x 24.6 x 13.1 inches
805.6 x 626.0 x 333.0mm
31.7 x 23.1 x 3.7 inches
805.6 x 587.4 x 96.2 mm
36.5 x 27.8 x 14.7 inches
929.0 x 706.9 x 374.7 mm
36.5 x26.1 x 3.8 inches
929.0 x 665.0 x 98.7 mm
40.8 x 31.3 x 14.9 inches
1037.8 x 796.4 x 379.5 mm
40.8 x 29.4 x 3.1 inches
1037.8 x 747.0 x 80.8 mm
31.7 pounds / 14.4 kg
26.8 pounds / 12.2 kg
46.7 pounds / 21.2 kg
39.9 pounds / 18.1 kg
53.1 pounds / 24.1 kg
44.9 pounds / 20.4 kg
52LG60
(52LG60-UA)
47LG60
(47LG60-UA)
45.3 x 34.1 x 17.1 inches
1152.8 x 868.6 x 434.5 mm
45.3 x 32.3 x 3.1 inches
1152.8 x 820.8 x 79.0 mm
50.3 x 37.1 x 16.9 inches
1280.1 x 944.7 x 430.0 mm
50.3 x 35.2 x 3.5 inches
1280.1 x 896.0 x 89.0 mm
71.8 pounds / 32.6 kg
59.3 pounds / 26.9 kg
99.2 pounds / 45.0 kg
83.9 pounds / 38.1 kg
32LG70
(32LG70-UA)
42LG70
(42LG70-UA)
31.3 x 23.5 x 8.9 inches
797.0 x 597.0 x 227.3 mm
31.3 x 21.9 x 3.9 inches
797.0 x 558.6 x 100.5 mm
40.4 x 28.8 x 11.5 inches
1026.2 x 734.0 x 293.4 mm
40.4 x 27.0 x 4.4 inches
1026.2 x 687.9 x 111.8 mm
28.4 pounds / 12.9 kg
25.1 pounds / 11.4 kg
49.3 pounds / 22.4 kg
43.4 pounds / 19.7 kg
47LG70
(47LG70-UA)
52LG70
(52LG70-UA)
44.8 x 32.2 x 13.5 inches
1140.4 x 820.1 x 342.9 mm
44.8 x 30.1 x 5.0 inches
1140.4 x 764.8 x 129.0 mm
50.5 x 35.3 x 13.5 inches
1284.4 x 898.6 x 342.9 mm
50.5 x 33.2 x 5.0 inches
1284.4 x 844.6 x 129.5 mm
66.3 pounds / 30.1 kg
55.9 pounds / 25.4 kg
87.9 pounds / 39.9 kg
77.6 pounds / 35.2 kg
AC100-240V ~ 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
MODÈLES
Dimensions
(Width x Height
x Depth)
Weight
With stand
Without stand
With stand
Without stand
MODÈLES
Dimensions
(Width x Height
x Depth)
Weight
With stand
Without stand
With stand
Without stand
Power requirement
Television System
Program Coverage
External Antenna Impedance
Environment
condition
■
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
42PG25
(42PG60-UA)
50PG25
(50PG60-UA)
41.1 x 28.9 x 12.1 inches
1044.4 x 735.4 x 308.0 mm
41.1 x 26.7 x 3.1 inches
1044.4 x 680.6 x 79.6 mm
48.6 x 33.4 x 14.3 inches
1235.6 x 849.3 x 364.1 mm
48.6 x 31.2 x 3.1 inches
1235.6 x 792.8 x 79.6 mm
61.7 pounds / 28.0 kg
55.1 pounds / 25.0 kg
96.3 pounds / 43.7 kg
87.5 pounds / 39.7 kg
50PG60
(50PG60F-UA)
60PG60
(60PG60F-UA)
48.6 x 33.4 x 14.3 inches
1235.6 x 849.3 x 364.1 mm
48.6 x 31.2 x 3.1 inches
1235.6 x 792.8 x 79.6 mm
57.3 x 38.8 x 16.3 inches
1455.0 x 985.0 x 414.0 mm
57.3 x 36.4 x 3.3 inches
1455.0 x 924.8 x 84.1 mm
100.7 pounds / 45.7 kg
91.9 pounds / 41.7 kg
137.5 pounds / 62.4 kg
121.0 pounds / 54.9 kg
AC100-240V ~ 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
123
APPENDIX
PROGRAMMING THE REMOTE CONTROL
The provided universal remote control can be programmed to operate most remote-controllable devices.
Note that the remote may not control all models of other brands.
Programming a code into a remote mode
APPENDIX
124
1
Testing your remote control.
To find out whether your remote control can operate other components without programming, turn on a
component such as a STB and press the corresponding mode button (such as a S T B) on the remote control, while pointing at the component. Test the P O W E R and C H
buttons to see if the component
responds correctly. If the component does not operate correctly, the remote control requires programming
to operate the device.
2
Turn on the component to be programmed, then press the corresponding mode button (such as S T B) on
the remote control. The remote control button of the desired device is illuminated.
3
Press the M E N U and M U T E buttons simultaneously, and the remote control is ready to be programmed with
the code.
4
Enter a code number using the number buttons on the remote control. Programming code numbers for the
corresponding component can be found on the following pages. If the code is correct, the device will turn
off.
5
Press the M E N U button to store the code.
6
Test the remote control functions to see if the component responds correctly. If not, repeat from step 2.
Remote Control Code
VCR
Brand
AIWA
AKAI
Codes
Codes
Brand
MAGNAVOX
031
067
012
069
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
SAMSUNG
043 046 124
146
MARANTZ
033
023
037
031
103
039 043
129
033
MARTA
MATSUI
MEI
MEMOREX
040
033
007
108
116
135
041
010 064
110 111
117 119
MGA
MINOLTA
MITSUBISHI
023 039 043
053
017
031
037
131
008
025
034
046
138
009
027
035
101
153
010
033
109
136
012
018
063
033
033
013
066
063 072
144 147
031
050
150
034
048
012
106
033 043
055 060
152
039 043
045
026 034
137 150
015 033
101
MTC
MULTITECH
NEC
NORDMENDE
OPTONICA
PANASONIC
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
REALISTIC
013 020
114 123
009 013 014
034 101 106
RICO
RUNCO
SALORA
013
063
031
031
067
101
013
108
072
011
033
013
040
107
145
003
031
053
058
148
014
033 034 041
068
031 033 067
030
033
010
034
102
046
020
020
051
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
014
066
020
041
109
147
008
033
054
075
033
062
140
145
034
063
144
010 014
034 040
101
Codes
032
105
113
125
SANSUI
022
SANYO
003
102
SCOTT
017
131
SEARS
003
013
031
101
SHARP
031
SHINTOM
024
SONY
003
056
077
SOUNDESIGN
034
STS
013
SYLVANIA
031
067
SYMPHONIC
034
TANDY
010
TATUNG
039
TEAC
034
TECHNICS
031
TEKNIKA
019
101
THOMAS
034
TMK
006
TOSHIBA
008
059
TOTEVISION
040
UNITECH
040
VECTOR RESEARCH 012
VICTOR
048
VIDEO CONCEPTS 012
VIDEOSONIC
040
WARDS
003
031
053
YAMAHA
012
ZENITH
034
058
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
008 009 010
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
APPENDIX
034
016
125
AMPRO
072
ANAM
031
AUDIO DYNAMICS 012
BROKSONIC
035
CANON
028
CAPEHART
108
CRAIG
003
CURTIS MATHES 031
DAEWOO
005
065
112
DAYTRON
108
DBX
012
DYNATECH
034
ELECTROHOME 059
EMERSON
006
029
036
129
FISHER
003
FUNAI
034
GE
031
107
GO VIDEO
132
HARMAN KARDON
HITACHI
004
043
INSTANTREPLAY 031
JCL
031
JCPENNY
012
040
JENSEN
043
JVC
012
048
130
KENWOOD
014
047
LG (GOLDSTAR) 001
101
LLOYD
034
LXI
003
017
MAGIN
040
Brand
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
125
APPENDIX
HDSTB
Brand
Codes
ALPHASTAR DSR
AMPLICA
BIRDVIEW
CHANNEL MASTER
123
050
051
013
036
CHAPARRAL
008
CITOH
054
CURTIS MATHES 050
DRAKE
005
011
141
DX ANTENNA
024
ECHOSTAR
038
093
097
122
ELECTRO HOME 089
EUROPLUS
114
FUJITSU
017
133
GENERAL INSTRUMENT 003
031
HITACHI
139
APPENDIX
126
Brand
126 129
014 015 018
055
009 012 077
145
006 007 010
052 112 116
046
040
094
098
056
057
095
099
076
058
096
100
021 022 027
134
004 016 029
059 101
140
Codes
HOUSTON TRACKER 033
057
HUGHES
068
JANIEL
060
JERROLD
061
KATHREIN
108
LEGEND
057
LG
001
LUTRON
132
LUXOR
062
MACOM
010
065
MEMOREX
057
NEXTWAVE
028
NORSAT
069
PACE SKY SATELLITE 143
PANASONIC
060
PANSAT
121
PERSONAL CABLE 117
PHILIPS
071
PICO
105
PRESIDENT
019
PRIMESTAR
030
037 039 051
104
147
144
059 063 064
124 125
070
142
102
110 111
Brand
Codes
PROSAT
RCA
REALISTIC
SAMSUNG
SATELLITE SERVICE CO
072
066
043
123
028
085
SCIENTIFIC ATLANTA 032
SONY
103
STARCAST
041
SUPER GUIDE
020
TEECOM
023
088
137
TOSHIBA
002
UNIDEN
016
044
078
101
VIEWSTAR
115
WINEGARD
128
ZENITH
081
091
106
074
035 047 057
138
124 125
026 075 087
090 107 130
127
025 042 043
045 048 049
079 080 086
135 136
146
082 083 084
120
DVD
Brand
Codes
APEX DIGITAL
022
DENON
020
GE
005
HARMAN KARDON
JVC
012
LG
001
MAGNAVOX
013
MARANTZ
024
014
006
027
010 016 025
Brand
Codes
Brand
Codes
MITSUBISHI
NAD
ONKYO
PANASONIC
PHILIPS
PIONEER
PROCEED
PROSCAN
002
023
008
003
013
004
021
005
RCA
SAMSUNG
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
005
011
007
005
019
009
010
017
009
026
006
006
015
006
008
018
016 025
IR CODES
1. How to Connect
■
Connect your wired remote control to the Remote Control port on the TV.
2. Remote Control IR Codes
■
Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
Tc
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
■
Configuration of frame
1st frame
Lead code
Low custom code
High custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
Repeat frame
Repeat code
■
Tf
Lead code
9 ms
4.5 ms
APPENDIX
■
Repeat code
0.55 ms
9 ms
■
2.25 ms
Bit description
Bit ”0”
Bit ”1”
0.56 ms
0.56 ms
2.24 ms
1.12 ms
■
Frame interval: Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
127
APPENDIX
(Hexa)
Code
Function
Note
08
POWER
Remote control Button (Power On/Off) D6
45
Q.MENU
Remote control Button
43
MENU
Remote control Button
0B
INPUT
Remote control Button
10-19
Number Key 0-9
Remote control Button
4C
- (Dash)
Remote control Button
1A
FLASHBK
Remote control Button
09
MUTE
Remote control Button
02
VOL +
Remote control Button
03
VOL -
Remote control Button
00
CH
Remote control Button
01
CH
Remote control Button
1E
FAV
Remote control Button
40
Remote control Button
41
Remote control Button
07
Remote control Button
06
Remote control Button
APPENDIX
44
ENTER
Remote control Button
5B
RETURN
Remote control Button
7E
SIMPLINK
Remote control Button
30
AV MODE
Remote control Button
B0
PLAY
Remote control Button
BA
PAUSE
Remote control Button
B1
STOP
Remote control Button
BD
REC
Remote control Button
8F
REW
Remote control Button
8E
FF
Remote control Button
Code
(Hexa)
Function
TV
Note
Discrete IR Code
(TV Input Selection)
C4
POWER ON
Discrete IR Code
(Only Power On)
C5
POWER OFF
Discrete IR Code
(Only Power Off)
5A
AV or AV1
Discrete IR Code
(AV or AV1 Input Selection)
D0
AV2
Discrete IR Code
(AV2 Input Selection)
BF
COMPONENT1
D4
COMPONENT2
Discrete IR Code
(Component1 Input Selection)
Discrete IR Code
(Component2 Input Selection)
D5
RGB-PC
Discrete IR Code
(RGB-PC Input Selection)
CE
HDMI1
Discrete IR Code
(HDMI1 Input Selection)
CC
HDMI2
E9
HDMI3
Discrete IR Code
(HDMI2 Input Selection)
Discrete IR Code
(HDMI3 Input Selection)
DA
HDMI4
Discrete IR Code
(HDMI4 Input Selection)
76
Ratio 4:3
Discrete IR Code
(Only 4:3 Mode)
77
Ratio 16:9
Discrete IR Code
AF
Ratio Zoom
Discrete IR Code
(Only 16:9 Mode)
(Only Zoom1 Mode)
* Use this feature depending on your model.
128
EXTERNAL CONTROL THROUGH RS-232C - Except 32/37/42/47/52LG60
The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the TV’s functions externally.
■ Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software.
The instructions below are provided to help with programming software or to test functionality using telenet
software.
RS-232C Setup
CABLE IN
i.e)
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
COAXIAL
AUDIO OUT
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
R
PC
Type of Connector; D-Sub 9-Pin Male
Pin Name
1
2
3
4
5
6
7
8
9
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
Baud rate : 9600 bps (UART)
■ Data length : 8 bits
■ Parity : None
■ Stop bit : 1 bit
■ Communication code : ASCII code
■ Use a crossed (reverse) cable.
■
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
APPENDIX
No.
Communication Parameters
! NOTE
G
No Connection
1
5
6
9
This product has command echo back in the
RS-232C Command.
129
APPENDIX
RS-232C Configurations
Either cable below can be used.
7-Wire Configuration
(Serial female-female NULL modem cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
3-Wire Configurations
(Not standard)
TXD
RXD
GND
DSR
DTR
CTS
RTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
RXD
TXD
GND
DTR
DSR
RTS
CTS
Set ID
Use this function to specify a TV ID number.
Refer to ‘Real Data Mapping1’. G p.133.
OPTION
Move
Language
Enter
: English
Input Label
Move
Language
Enter
: English
Input Label
SIMPLINK
: On
SIMPLINK
Key Lock
: Off
Key Lock
: Off
Caption
: Off
Caption
: Off
ISM Method
: On
ISM Method
Power Saving
: Level 0
Power Saving
Set ID
:1
Set ID
E
: Level 0
:1
F
1
E
APPENDIX
Close
1 MENU
2
ENTER
3
ENTER
4RETURN
MENU
130
OPTION
Select O P T I O N.
Select Set ID.
Choose the desired TV ID number.
The adjustment range of Set ID is
1~99.
Return to the previous menu.
Return to TV viewing.
G
TXD
RXD
GND
DTR
DSR
RTS
CTS
Command Reference List
COMMAND1 COMMAND2
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control
Lock Mode
k
x
k
k
k
k
k
k
k
k
k
k
a
b
c
d
e
f
g
h
i
j
k
l
DATA
(Hexadecimal)
00 ~ 01
(G p.132)
(G p.132)
00 ~ 01
00 ~ 01
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 01
COMMAND1 COMMAND2
14. Treble
15. Bass
16. Balance
17. Color Temperature
18. ISM Method
19. Power Saving
20. Auto Configuration
22. Channel Add/Del
23. Key
24. Backlight
k
k
k
k
j
j
j
m
m
m
DATA
(Hexadecimal)
r
s
t
u
p
q
u
b
c
g
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 02
(G p.134)
00 ~ 01
(G p.134)
00 ~ 01
(G p.135)
00 ~ 64
Only LCD TV Model
Only Plasma TV Model
k
m
COMMAND1 COMMAND2
21. Channel Tuning
m
a
00 ~ 01
DATA00
DATA01
DATA02
DATA03
DATA04
DATA05
(Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal)
physical
major
major low
program high program low
minor high
minor low
attribute
Transmission / Receiving Protocol
Transmission
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is
data read mode, it indicates present status data. If the data is
data write mode, it returns the data of the PC computer.
Error Acknowledgement
APPENDIX
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
[Set ID] : You can adjust the set ID to choose desired TV ID
number in Setup menu. Adjustment range is 1~ 99.
When selecting Set ID ‘0’, every connected the TV is
controlled. Set ID is indicated as decimal (1~ 99) on
menu and as Hexa decimal (0x0~ 0x63) on transmission
/receiving protocol.
[DATA] : To transmit the command data.
Transmit the ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
* In this model, TV will not send the status during the standby mode.
* In this model, TV will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[OK] : Use the large character.
[Command2][ ][Set ID][ ][NG][Data][x]
The TV transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions
or communication errors.
Data1: Illegal Code
Data2: Not supported function
Data3: Wait more time
* In this model, TV will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[NG] : Use the large character
131
APPENDIX
01. Power (Command: k a)
05. Volume Mute (Command: k e)
To control Power On/Off of the TV.
To control volume mute on/off.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
You can also adjust mute using the MUTE button on
remote control.
Data 00: Power Off
Data 01: Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][e][ ][Set ID][ ][Data][Cr]
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback
presents status about each function.
Data 00: Volume mute on (Volume off)
* Note: In this model, TV will send the Acknowledge
after power on processing completion.
There might be a time delay between command and
acknowledge.
02. Input Select (Command: x b)
To select input source for TV.
Data 01: Volume mute off (Volume on)
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
06. Volume Control (Command: k f)
To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Transmission [x][b][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’. See page 133.
Data 00: DTV (Antenna)
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
Data 01: DTV (Cable)
Data 10: Analog (Antenna) Data 11: Analog (Cable)
Data 20: AV1
Data 21: AV2
Data 40: Component 1
Data 41: Component 2
To adjust screen contrast.
Data 60: RGB-PC
Data 90: HDMI1
You can also adjust contrast in the PICTURE menu.
Data 91: HDMI2
Data 92: HDMI3
Transmission [k][g][ ][Set ID][ ][Data][Cr]
07. Contrast (Command: k g)
Data 93: HDMI4
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
*Refer to ‘Real data mapping’. See page 133.
* Use the feature depending on your model.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
03. Aspect Ratio (Command: k c)
To adjust the screen format.
08. Brightness (Command: k h)
To adjust screen brightness.
APPENDIX
Transmission [k][c][ ][Set ID][ ][Data][Cr]
You can also adjust brightness in the PICTURE menu.
Data 01: 4:3
05: Zoom 2
Transmission [k][h][ ][Set ID][ ][Data][Cr]
02: 16:9
06: Set by program
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
04: Zoom 1
09: Just scan
*Refer to ‘Real data mapping’. See page 133.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
Reserved
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
04. Screen Mute (Command: k d)
To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00: Screen mute off (Picture on)
Data 01: Screen mute on (Picture off)
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
132
09. Color (Command: k i)
14. Treble (Command: k r)
To adjust screen color.
To adjust treble.
You can also adjust color in the PICTURE menu.
You can also adjust treble in the AUDIO menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’ as shown below.
*Refer to ‘Real data mapping’ as shown.
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
10. Tint (Command: k j)
15. Bass (Command: k s)
To adjust screen tint.
To adjust bass.
You can also adjust tint in the PICTURE menu.
You can also adjust bass in the AUDIO menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Red: 00 ~ Green: 64 (*transmit by Hexadecimal code)
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’ as shown below.
*Refer to ‘Real data mapping’ as shown below.
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
11. Sharpness (Command: k k)
16. Balance (Command: k t)
To adjust screen sharpness.
To adjust balance.
You can also adjust sharpness in the PICTURE menu.
You can also adjust balance in the AUDIO menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’ as shown below.
*Refer to ‘Real data mapping’ as shown below.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
12. OSD Select (Command: k l)
17. Color Temperature (Command: k u)
To adjust color temperature.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
You can also adjust color temperature in the PICTURE menu.
Data 00: OSD off
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Data 01: OSD on
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
Data 00: Medium 01: Cool 02: Warm
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
13. Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel controls
on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off
Data 01: Lock on
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
If you’re not using the remote control and front panel
controls on the TV, use this mode. When main power is
on/off, remote control lock is released.
APPENDIX
To select OSD (On Screen Display) on/off.
*Real data mapping
0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
133
APPENDIX
18. ISM Method (Command: j p)
(Only Plasma TV model)
To avoid having a fixed image remain on screen.
Transmission [ j ][p][ ][Set ID][ ][Data][Cr]
Data 01: Inversion
04: White Wash
02: Orbiter
08: Normal
Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
19. Power saving (Command: j q)
(Only Plasma TV model)
To control the power saving function on/off.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Data 00: Power saving off (Power Saving Level 0)
01: Power saving on (Power Saving Level 4)
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
20. Auto Configuration (Command: j u)
To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
Data 1: To set
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
21. Channel Tuning (Command: m a)
To tune channel to following physical/major/minor number.
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
APPENDIX
Digital channels have a Physical, Major, and Minor channel
number. The Physical number is the actual digital channel
number, the Major is the number that the channel should
be mapped to, and the Minor is the sub-channel. Since
the ATSC tuner automatically maps the channel to the
Major number, the Physical number is not required when
sending a command.
Data 00: Physical Channel Number
NTSC air: 02~45, NTSC cable: 01, 0E~7D
ATSC air: 01~45, ATSC cable: 01~87
Data 01 & 02: Major Channel Number
Data 01: High byte
Data 02: Low byte
Two bytes are available for the Major and Minor, normally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.
134
Data05:
7
Main/Sub
Picture
6
Two/One
Part Channel
5
Using Physical
Channel
4
3
2
1
0
Step
NTSC Air
NTSC Cable
ATSC Air
ATSC Cable_std
ATSC Cable_hrc
ATSC Cable_irc
ATSC cable_auto
Reserved
...
Reserved
Reserved
0 Main
0 Two
0 Use
x
0
0
0
0
1 Sub
1 One
1 No Use
x
0
0
0
1
x
0
0
1
0
x
0
0
1
1
x
0
1
0
0
x
0
1
0
1
x
0
1
1
0
x
0
1
1
1
x
x
x
x
x
x
1
1
1
1
The table above lists the binary code which must be
converted to Hexadecimal before sending. For example:
The binary code to tune the sub source to an NTSC
cable channel is “1000 0001”, which translates to “81”
in Hex.
* 7th bit : For which source do you want to change the
channel.
* 6th bit: Use a two part or one part channel. Most cases
just use 0 since it’s ignored when using NTSC.
* 5th bit: Use 0 with NTSC since it can only use the physical channel number. Normally use 1 for ATSC since most
times it doesn’t matter what the physical number is.
* 4th bit: Set to 0.
* 3-0 bits: Choose signal type.
22. Channel Add/Del (Command: m b)
To add and delete the channels
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Channel Delete
Data 01: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
23. Key (Command: m c)
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code: Refer to page 128.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
24. Backlight (Command: m g)
(Only LCD TV model)
To adjust screen backlight.
* Tune Command Examples:
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 133.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
APPENDIX
1. Tune to the analog (NTSC) cable channel 35.
Data 00 = Physical of 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = 0000 0001 in binary = 01
Total = ma 00 23 00 00 00 00 01
2. Tune to the digital (ATSC) local channel 30-3.
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = 0010 0010 in binary = 22
Total = ma 00 00 00 1E 00 03 22
Acknowledgement[a][ ][Set ID][ ][OK][Data00][Data01]
[Data02][Data03][Data04][x][a][ ][Set ID]
[ ][NG][Data00][x]
135
APPENDIX
OPEN SOURCE LICENSE - This feature is not available for all models.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.
the program proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone's free use or not
licensed at all.
The precise terms and conditions for copying, distribution and
modification follow.
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public License is intended to guarantee your freedom to share
and change free software - to make sure the software is free for
all its users. This General Public License applies to most of the
Free Software Foundation's software and to any other program
whose authors commit to using it. (Some other free software
foundation software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source code
or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can
do these things.
APPENDIX
To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the
rights. These restrictions translate to certain responsibilities for
you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get
the source code. And you must show them these terms so they
know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
136
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This license applies to any program or other work which contains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The
"Program", below, refers to any such program or work, and a
"work based on the Program" means either the Program or any
derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with
modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the
term "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification
are not covered by this license; they are outside its scope.
The act of running the Program is not restricted, and the output from the program is covered only if its contents constitute
a work based on the program (independent of having been
made by running the program). Whether that is true depends
on what the program does.
1. You may copy and distribute verbatim copies of the program's
source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this license and to the
absence of any warranty; and give any other recipients of the
program a copy of this license along with the Program.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this
free software. If the software is modified by someone else and
passed on, we want its recipients to know that what they have is
not the original, so that any problems introduced by others will
not reflect on the original authors' reputations.
2. You may modify your copy or copies of the program or any
portion of it, thus forming a work based on the Program, and
copy and distribute such modifications or work under the
terms of section 1 above, provided that you also meet all of
these conditions:
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the date of
any change.
b) You must cause any work that you distribute or publish,
that in whole or in part contains or is derived from the
Program or any part there of, to be licensed as a whole at
no charge to all third parties under the terms of this
license.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print
or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users
may redistribute the program under these conditions, and
telling the user how to view a copy of this license.
(Exception: if the Program itself is interactive but does not
normally print such an announcement, your work based on
the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and
separate works in themselves, then this license, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as
part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this license,
whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who
wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of
derivative or collective works based on the program.
3. You may copy and distribute the program (or a work based on
it, under section 2) in object code or executable form under
the terms of sections 1 and 2 above provided that you also
do one of the following:
a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of sections 1 and 2 above on a medium customarily
used for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a
complete machine-readable copy of the corresponding
source code, to be distributed under the terms of sections
1 and 2 above on a medium customarily used for software
interchange; or,
The source code for a work means the preferred form of the
work for making modifications to it. For an executable work,
complete source code means all the source code for all modules it contains, plus any associated interface definition files,
plus the scripts used to control compilation and installation
of the executable. However, as a special exception, the source
code distributed need not include anything that is normally
distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating
system on which the executable runs, unless that component
itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same
place counts as distribution of the source code, even though
third parties are not compelled to copy the source along with
the object code.
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this license. Any attempt
otherwise to copy, modify, sublicense or distribute the
Program is void, and will automatically terminate your rights
under this license. However, parties who have received copies,
or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this license, since you have not
signed it. However, nothing else grants you permission to
modify or distribute the Program or its derivative works.
These actions are prohibited by law if you do not accept this
license. Therefore, by modifying or distributing the program
(or any work based on the program), you indicate your acceptance of this license to do so, and all its terms and conditions
for copying, distributing or modifying the program or works
based on it.
APPENDIX
In addition, mere aggregation of another work not based on
the program with the Program (or with a work based on the
program) on a volume of a storage or distribution medium
does not bring the other work under the scope of this license.
c) Accompany it with the information you received as to the
offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and
only if you received the program in object code or executable form with such an offer, in accord with Subsection
b above.)
6. Each time you redistribute the program (or any work based on
the Program), the recipient automatically receives a license
from the original licensor to copy, distribute or modify the
Program subject to these terms and conditions. You may not
impose any further restrictions on the recipients' exercise of
the rights granted herein. You are not responsible for enforcing compliance by third parties to this license.
137
APPENDIX
7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any
other pertinent obligations, then as a consequence you may
not distribute the program at all. For example, if a patent
license would not permit royalty-free redistribution of the
program by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it and
this license would be to refrain entirely from distribution of
the program.
any later version published by the Free Software Foundation.
If the program does not specify a version number of this
license, you may choose any version ever published by the
Free Software Foundation.
10.If you wish to incorporate parts of the program into other free
programs whose distribution conditions are different, write to
the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the
free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended to
apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of
protecting the integrity of the free software distribution system, which is implemented by public license practices. Many
people have made generous contributions to the wide range
of software distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot
impose that choice.
APPENDIX
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this license.
8. If the distribution and/or use of the program is restricted in
certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the program
under this license may add an explicit geographical distribution
limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In
such case, this license incorporates the limitation as if written
in the body of this license.
9. The Free Software Foundation may publish revised and/or
new versions of the General Public License from time to time.
Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the
program specifies a version number of this license which
applies to it and "any later version", you have the option of
following the terms and conditions either of that version or of
138
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS
IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to apply these terms to your new programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to
make it free software which everyone can redistribute and change
under these terms.
To do so, attach the following notices to the program. It is safest
to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at
least the "copyright" line and a pointer to where the full notice is
found.
one line to give the program's name and a brief idea of what it
does.
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License as
published by the Free Software Foundation; either version 2 of
the license, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public
License along with this program; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301 USA.
Also add information on how to contact you by electronic and
paper mail.
If the program is interactive, make it output a short notice like
this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for
details type ‘show w’. This is free software, and you are welcome
to redistribute it under certain conditions; type ‘show c’ for
details.
The hypothetical commands ‘show w’ and ‘show c’ should show
the appropriate parts of the General Public License. Of course,
the commands you use may be called something other than
‘show w’ and ‘show c’; they could even be mouse-clicks or menu
items-whatever suits your program.
You should also get your employer (if you work as a programmer)
or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by
James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your
program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to
do, use the GNU Lesser General Public License instead of this
license.
APPENDIX
139
APPENDIX
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public Licenses are intended to guarantee your freedom to share
and change free software - to make sure the software is free for
all its users.
This license, the Lesser General Public License, applies to some
specially designated software packages - typically libraries - of
the Free Software Foundation and other authors who decide to
use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public
License is the better strategy to use in any particular case, based
on the explanations below.
APPENDIX
When we speak of free software, we are referring to freedom of
use, not price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive
source code or can get it if you want it; that you can change the
software and use pieces of it in new free programs; and that you
are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender
these rights. These restrictions translate to certain responsibilities
for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis
or for a fee, you must give the recipients all the rights that we
gave you. You must make sure that they, too, receive or can get
the source code. If you link other code with the library, you must
provide complete object files to the recipients, so that they can
relink them with the library after making changes to the library
and recompiling it. And you must show them these terms so they
know their rights.
We protect your rights with a two-step method: (1) we copyright
the library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
140
To protect each distributor, we want to make it very clear that
there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know
that what they have is not the original version, so that the original author's reputation will not be affected by problems that
might be introduced by others.
Finally, software patents pose a constant threat to the existence
of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a
restrictive license from a patent holder. Therefore, we insist that
any patent license obtained for a version of the library must be
consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the
ordinary GNU General Public License. This license, the GNU
Lesser General Public License, applies to certain designated
libraries, and is quite different from the ordinary General Public
License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original library. The
ordinary General Public License therefore permits such linking
only if the entire combination fits its criteria of freedom. The
Lesser General Public License permits more lax criteria for linking
other code with the library.
We call this license the "Lesser" General Public License because
it does Less to protect the user's freedom than the ordinary
General Public License. It also provides other free software developers Less of an advantage over competing non-free programs.
These disadvantages are the reason we use the ordinary General
Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs
must be allowed to use the library. A more frequent case is that
a free library does the same job as widely used non-free libraries.
In this case, there is little to gain by limiting the free library to free
software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-free
programs enables a greater number of people to use a large body
of free software. For example, permission to use the GNU C
Library in non-free programs enables many more people to use
the whole GNU operating system, as well as its variant, the
GNU/Linux operating system.
Although the Lesser General Public License is Less protective of
the users' freedom, it does ensure that the user of a program that
is linked with the Library has the freedom and the wherewithal to
run that program using a modified version of the Library.
each copy an appropriate copyright notice and disclaimer of
warranty; keep intact all the notices that refer to this license
and to the absence of any warranty; and distribute a copy of
this license along with the Library.
The precise terms and conditions for copying, distribution and
modification follow. Pay close attention to the difference between
a "work based on the library" and a "work that uses the library".
The former contains code derived from the library, whereas the
latter must be combined with the library in order to run.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This license agreement applies to any software library or other
program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed
under the terms of this Lesser General Public License (also
called “this license”). Each license is addressed as "you".
A “library” means a collection of software functions and/or
data prepared so as to be conveniently linked with application
programs (which use some of those functions and data) to
form executables.
“Source code” for a work means the preferred form of the
work for making modifications to it. For a library, complete
source code means all the source code for all modules it contains, plus any associated interface definition files, plus the
scripts used to control compilation and installation of the
library.
Activities other than copying, distribution and modification
are not covered by this license; they are outside its scope.
The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the library (independent of
the use of the Library in a tool for writing it). Whether that is
true depends on what the library does and what the program
that uses the library does.
1. You may copy and distribute verbatim copies of the library's
complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on
(For example, a function in a library to compute square roots
has a purpose that is entirely well-defined independent of the
application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be
optional: if the application does not supply it, the square root
function must still compute square roots.)
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the
library, and can be reasonably considered independent and
separate works in themselves, then this license, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as
part of a whole which is a work based on the library, the distribution of the whole must be on the terms of this license,
whose permissions for other licenses extend to the entire
whole, and thus to each and every part regardless of who
wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of
derivative or collective works based on the library.
APPENDIX
The “Library”, below, refers to any such software library or work
which has been distributed under these terms. A “work based
on the Library” means either the Library or any derivative work
under copyright law: that is to say, a work containing the
library or a portion of it, either verbatim or with modifications
and/or translated straightforwardly into another language.
(Hereinafter, translation is included without limitation in the
term “modification”.)
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library, and
copy and distribute such modifications or work under the
terms of section 1 above, provided that you also meet all of
these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent
notices stating that you changed the files and the date of
any change.
c) You must cause the whole of the work to be licensed at no
charge to all third parties under the terms of this license.
d) If a facility in the modified Library refers to a function or a
table of data to be supplied by an application program that
uses the facility, other than as an argument passed when
the facility is invoked, then you must make a good faith
effort to ensure that, in the event an application does not
supply such function or table, the facility still operates, and
performs whatever part of its purpose remains meaningful.
In addition, mere aggregation of another work not based on
the library with the library (or with a work based on the
library) on a volume of a storage or distribution medium does
not bring the other work under the scope of this license.
141
APPENDIX
3. You may opt to apply the terms of the ordinary GNU General
Public License instead of this License to a given copy of the
Library. To do this, you must alter all the notices that refer to
this License, so that they refer to the ordinary GNU General
Public License, version 2, instead of to this License. (If a newer
version than version 2 of the ordinary GNU General Public
License has appeared, then you can specify that version
instead if you wish.) Do not make any other change in these
notices.
Once this change is made in a given copy, it is irreversible for
that copy, so the ordinary GNU General Public License applies
to all subsequent copies and derivative works made from that
copy.
This option is useful when you wish to copy part of the code
of the library into a program that is not a library.
4. You may copy and distribute the library (or a portion or derivative of it, under Section 2) in object code or executable form
under the terms of Sections 1 and 2 above provided that you
accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of sections 1 and 2 above on a medium customarily
used for software interchange.
If distribution of object code is made by offering access to
copy from a designated place, then offering equivalent access
to copy the source code from the same place satisfies the
requirement to distribute the source code, even though third
parties are not compelled to copy the source along with the
object code.
APPENDIX
5. A program that contains no derivative of any portion of the
Library, but is designed to work with the Library by being
compiled or linked with it, is called a “work that uses the
Library”. Such a work, in isolation, is not a derivative work of
the Library, and therefore falls outside the scope of this
license.
However, linking a “work that uses the library” with the Library
creates an executable that is a derivative of the Library
(because it contains portions of the library), rather than a
“work that uses the library”. The executable is therefore covered by this license. Section 6 states terms for distribution of
such executable.
When a “work that uses the library” uses material from a header file that is part of the library, the object code for the work
may be a derivative work of the library even though the source
code is not.
Whether this is true is especially significant if the work can be
linked without the library, or if the work is itself a library. The
threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data
structure layouts and accessories, and small macros and small
inline functions (ten lines or less in length), then the use of
142
the object file is unrestricted, regardless of whether it is legally a derivative work. (Executable containing this object code
plus portions of the library will still fall under Section 6.)
Otherwise, if the work is a derivative of the library, you may
distribute the object code for the work under the terms of
Section 6. Any executable containing that work also fall under
Section 6, whether or not they are linked directly with the
library itself.
6. As an exception to the sections above, you may also combine
or link a "work that uses the library" with the library to produce a work containing portions of the library, and distribute
that work under terms of your choice, provided that the terms
permit modification of the work for the customer's own use
and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work
that the library is used in it and that the Library and its use
are covered by this license. You must supply a copy of this
license. If the work during execution displays copyright
notices, you must include the copyright notice for the library
among them, as well as a reference directing the user to the
copy of this license. Also, you must do one of these things:
a) Accompany the work with the complete corresponding
machine-readable source code for the library including
whatever changes were used in the work (which must be
distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete
machine-readable “work that uses the Library”, as object
code and/or source code, so that the user can modify the
library and then relink to produce a modified executable
containing the modified library. (It is understood that the
user who changes the contents of definitions files in the
library will not necessarily be able to recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the
library. A suitable mechanism is one that (1) uses at run time
a copy of the library already present on the user’s computer
system, rather than copying library functions into the executable, and (2) will operate properly with a modified version
of the library, if the user installs one, as long as the modified
version is interface-compatible with the version that the
work was made with.
c) Accompany the work with a written offer, valid for at least
three years, to give the same user the materials specified in
Subsection 6, above, for a charge no more than the cost of
performing this distribution.
d) If distribution of the work is made by offering access to
copy from a designated place, offer equivalent access to
copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these
materials or that you have already sent this user a copy.
For an executable, the required form of the "work that uses
the library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not
include anything that is normally distributed (in either source
or binary form) with the major components (compiler, kernel,
and so on) of the operating system on which the executable
runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license
restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction
means you cannot use both them and the library together in
an executable that you distribute.
7. You may place library facilities that are a work based on the
library side-by-side in a single library together with other
library facilities not covered by this license, and distribute
such a combined library, provided that the separate distribution of the work based on the Library and of the other library
facilities is otherwise permitted, and provided that you do
these two things:
a) Accompany the combined library with a copy of the same
work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms
of the sections above.
b) Give prominent notice with the combined library of the
fact that part of it is a work based on the library, and
explaining where to find the accompanying uncombined
form of the same work.
9. You are not required to accept this license, since you have not
signed it. However, nothing else grants you permission to modify or distribute the library or its derivative works. These
actions are prohibited by law if you do not accept this license.
Therefore, by modifying or distributing the library (or any work
based on the library), you indicate your acceptance of this
license to do so, and all its terms and conditions for copying,
distributing or modifying the library or works based on it.
10.Each time you redistribute the library (or any work based on
the Library), the recipient automatically receives a license
from the original licensor to copy, distribute, link with or modify the library subject to these terms and conditions. You may
not impose any further restrictions on the recipients' exercise
11. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any
other pertinent obligations, then as a consequence you may
not distribute the library at all. For example, if a patent license
would not permit royalty-free redistribution of the library by
all those who receive copies directly or indirectly through
you, then the only way you could satisfy both it and this
license would be to refrain entirely from distribution of the
library.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply, and the section as a whole is intended to
apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of
protecting the integrity of the free software distribution system which is implemented by public license practices. Many
people have made generous contributions to the wide range
of software distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute
software through any other system and a license cannot
impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this license.
12.If the distribution and/or use of the library is restricted in certain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the library under this
license may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted
only in or among countries not thus excluded. In such case,
this license incorporates the limitation as if written in the body
of this license.
APPENDIX
8. You may not copy, modify, sublicense, link with, or distribute
the library except as expressly provided under this license.
Any attempt otherwise to copy, modify, sublicense, link with,
or distribute the library is void, and will automatically terminate your rights under this license. However, parties who have
received copies, or rights, from you under this license will not
have their licenses terminated so long as such parties remain
in full compliance.
of the rights granted herein.
You are not responsible for enforcing compliance by third
parties with this license.
13.The Free Software Foundation may publish revised and/or
new versions of the Lesser General Public License from time to
time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the
library specifies a version number of this license which applies
to it and “any later version”, you have the option of following
the terms and conditions either of that version or of any later
version published by the Free Software Foundation.
143
APPENDIX
If the library does not specify a license version number, you
may choose any version ever published by the Free Software
Foundation.
14.If you wish to incorporate parts of the library into other free
programs whose distribution conditions are incompatible with
these, write to the author to ask for permission. For software
which is copyrighted by the Free Software Foundation, write
to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software generally.
To apply these terms, attach the following notices to the library.
It is safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should
have at least the “copyright” line and a pointer to where the full
notice is found.
one line to give the library's name and a brief idea of what it does.
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify
it under the terms of the GNU Lesser General Public License as
published by the Free Software Foundation; either version 2.1 of
the license, or (at your option) any later version.
NO WARRANTY
15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS
IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE
LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
APPENDIX
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to apply these terms to your new libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so
by permitting redistribution under these terms (or, alternatively,
under the terms of the ordinary General Public License).
144
This library is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more
details.
You should have received a copy of the GNU Lesser General
Public License along with this library; if not, write to the Free
Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
MA 02110-1301 USA
Also add information on how to contact you by electronic and
paper mail.
You should also get your employer (if you work as a programmer)
or your school, if any, to sign a “copyright disclaimer” for the
library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the
library ‘Frob’ (a library for tweaking knobs) written by James
Random Hacker.
signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice
MOZILLA PUBLIC LICENSE
Version 1.1
--------------code which is described in the source code notice
required by exhibit as original code, and which, at the time
of its release under this license is not already covered
code governed by this license.
1.Definitions.
1.0.1. “Commercial use” means distribution or otherwise making
the covered code available to a third party.
1.1.
“Contributor” means each entity that creates or contributes to the creation of modifications.
1.2.
“Contributor version” means the combination of the original code, prior modifications used by a contributor, and
the modifications made by that particular contributor.
1.3.
“Covered code” means the original code or modifications
or the combination of the original code and modifications,
in each case including portions thereof.
1.4.
“Electronic distribution mechanism” means a mechanism
generally accepted in the software development community for the electronic transfer of data.
1.5.
“Executable” means covered code in any form other than
source code.
“Initial developer” means the individual or entity identified
as the initial Developer in the Source Code notice required
by exhibit A.
1.7.
“Larger work” means a work which combines covered code
or portions thereof with code not governed by the terms
of this License.
1.8.
“License” means this document.
1.8.1. “Licensable” means having the right to grant, to the maximum extent possible, whether at the time of the initial
grant or subsequently acquired, any and all of the rights
conveyed herein.
1.9.
“Modifications” means any addition to or deletion from
the substance or structure of either the original code or
any previous modifications. When covered code is
released as a series of files, a modification is:
A. Any addition to or deletion from the contents of a file
containing original code or previous modifications.
B. Any new file that contains any part of the original code
or previous modifications.
1.11. “Source code” means the preferred form of the covered
code for making modifications to it, including all modules
it contains, plus any associated interface definition files,
scripts used to control compilation and installation of an
executable, or source code differential comparisons
against either the original code or another well known,
available covered code of the contributor's choice. The
source code can be in a compressed or archival form, provided the appropriate decompression or de-archiving software is widely available for no charge.
1.12. “You” (or “Your”) means an individual or a legal entity
exercising rights under, and complying with all of the terms
of, this license or a future version of this license issued
under section 6.1.
For legal entities, “You” includes any entity which controls,
is controlled by, or is under common control with You. For
purposes of this definition, “control” means (a) the power,
direct or indirect, to cause the direction or management of
such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
2. Source Code License.
2.1.
APPENDIX
1.6.
1.10.1.“Patent claims” means any patent claim(s), now owned or
hereafter acquired, including without limitation, method,
process, and apparatus claims, in any patent licensable by
grantor.
The initial developer grant.
The initial developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims:
a) under intellectual property rights (other than patent or
trademark) licensable by initial developer to use, reproduce, modify, display, perform, sublicense and distribute the original code (or portions thereof) with or without modifications, and/or as part of a larger work; and
(b) under patents claims infringed by the making, using or
selling of original code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise dispose
of the original code (or portions there of).
1.10. “Original code” means source code of computer software
145
APPENDIX
(c) the licenses granted in this section 2.1(a) and (b) are
effective on the date Initial developer first distributes
original code under the terms of this license.
(d) Notwithstanding section 2.1(b) above, no patent
license is granted: 1) for code that You delete from the
original Code; 2) separate from the original code; or
3) for infringements caused by: i) the modification of
the original code or ii) the combination of the original
code with other software or devices.
2.2.
APPENDIX
3. Distribution Obligations.
146
3.2.
Availability of source code.
Any modification which you create or to which you contribute must be made available in source code form under
the terms of this license either on the same media as an
executable version or via an accepted electronic distribution mechanism to anyone to whom you made an executable version available; and if made available via electronic distribution mechanism, must remain available for at
least twelve (12) months after the date it initially became
available, or at least six (6) months after a subsequent
version of that particular modification has been made
available to such recipients. You are responsible for ensuring that the source code version remains available even if
the electronic distribution mechanism is maintained by a
third party.
3.3.
Description of modifications.
You must cause all covered code to which you contribute to
contain a file documenting the changes You made to create
that covered code and the date of any change. You must
include a prominent statement that the modification is
derived, directly or indirectly, from original code provided by
the initial developer and including the name of the initial
developer in (a) the source code, and (b) in any notice in an
executable version or related documentation in which you
describe the origin or ownership of the covered code.
3.4.
Intellectual property matters
(a) Third party claims.
If contributor has knowledge that a license under a third
party's intellectual property rights is required to exercise
the rights granted by such contributor under sections 2.1
or 2.2, contributor must include a text file with the source
code distribution titled "LEGAL" which describes the claim
and the party making the claim in sufficient detail that a
recipient will know whom to contact. If contributor obtains
such knowledge after the modification is made available as
described in section 3.2, contributor shall promptly modify the LEGAL file in all copies contributor makes available
thereafter and shall take other steps (such as notifying
appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the covered code that
new knowledge has been obtained.
(b) Contributor APIs.
If contributor's modifications include an application
programming interface and contributor has knowledge of
patent licenses which are reasonably necessary to implement
that API, contributor must also include this information in
the LEGAL file.
Contributor Grant.
Subject to third party intellectual property claims, each
contributor hereby grants You a world-wide, royalty-free,
non-exclusive license
(a) under intellectual property rights (other than patent
or trademark) licensable by contributor, to use,
reproduce, modify, display, perform, sublicense and
distribute the modifications created by such contributor (or portions thereof) either on an unmodified
basis, with other modifications, as covered code
and/or as part of a larger work; and
(b) under patent claims infringed by the making, using, or
selling of modifications made by that contributor
either alone and/or in combination with its contributor
version (or portions of such combination), to make,
use, sell, offer for sale, have made, and/or otherwise
dispose of: 1) modifications made by that contributor
(or portions thereof); and 2) the combination of modifications made by that contributor with its contributor
version (or portions of such combination).
(c) the licenses granted in sections 2.2(a) and 2.2(b) are
effective on the date contributor first makes commercial use of the covered code.
(d) Notwithstanding section 2.2(b) above, no patent
license is granted: 1) for any code that contributor has
deleted from the contributor version; 2) separate from
the contributor version; 3) for infringements caused
by: i) third party modifications of contributor version
or ii) the combination of modifications made by that
contributor with other software (except as part of the
contributor version) or other devices; or 4) under
patent claims infringed by covered code in the
absence of modifications made by that contributor.
3.1.
You may not offer or impose any terms on any source code
version that alters or restricts the applicable version of
this license or the recipients' rights hereunder. However,
you may include an additional document offering the
additional rights described in section 3.5.
Application of license.
The modifications which You create or to which you contribute are governed by the terms of this license, including
without limitation section 2.2. The source code version of
covered code may be distributed only under the terms of
this license or a future version of this license released
under section 6.1, and you must include a copy of this
license with every copy of the source code you distribute.
3.5.
3.6.
(c) Representations.
contributor represents that, except as disclosed pursuant
to section 3.4(a) above, contributor believes that contributor's
modifications are contributor's original creation(s)
and/or contributor has sufficient rights to grant the rights
conveyed by this license.
3.7.
Required notices.
You must duplicate the notice in exhibit A in each file of
the source code. If it is not possible to put such notice in
a particular source code file due to its structure, then You
must include such notice in a location (such as a relevant
directory) where a user would be likely to look for such a
notice. If You created one or more modification(s), you
may add your name as a contributor to the notice
described in exhibit A. you must also duplicate this license
in any documentation for the source code where You
describe recipients' rights or ownership rights relating to
covered code. You may choose to offer, and to charge a
fee for, warranty, support, indemnity or liability obligations
to one or more recipients of covered code. However, you
may do so only on your own behalf, and not on behalf of
the Initial developer or any contributor. You must make it
absolutely clear than any such warranty, support, indemnity or liability obligation is offered by you alone, and You
hereby agree to indemnify the Initial developer and every
contributor for any liability incurred by the Initial developer or such contributor as a result of warranty, support,
indemnity or liability terms you offer.
4. Inability to comply due to statute or regulation.
If it is impossible for you to comply with any of the terms
of this license with respect to some or all of the covered
code due to statute, judicial order, or regulation then you
must: (a) comply with the terms of this license to the maximum extent possible; and (b) describe the limitations and
the code they affect. Such description must be included in
the LEGAL file described in section 3.4 and must be
included with all distributions of the source code. Except
to the extent prohibited by statute or regulation, such
description must be sufficiently detailed for a recipient of
ordinary skill to be able to understand it.
5. Application of this license.
This license applies to code to which the initial developer has
attached the notice in exhibit A and to related covered code.
6. Versions of the license.
6.1.
New versions.
Netscape communications corporation (“Netscape”) may
publish revised and/or new versions of the license from
time to time. Each version will be given a distinguishing
version number.
6.2.
Effect of new versions.
Once covered code has been published under a particular
version of the license, you may always continue to use it
under the terms of that version. You may also choose to
use such covered code under the terms of any subsequent
version of the license published by netscape. No one
other than netscape has the right to modify the terms
applicable to covered code created under this license.
6.3.
Derivative works.
If You create or use a modified version of this license
(which you may only do in order to apply it to code which
is not already covered code governed by this license), You
must (a) rename Your license so that the phrases
"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL",
"NPL" or any confusingly similar phrase do not appear in
your license (except to note that your license differs from
this license) and (b) otherwise make it clear that Your
version of the license contains terms which differ from the
Mozilla Public license and netscape Public License. (Filling
in the name of the initial developer, original code or contributor in the notice described in exhibit A shall not of
themselves be deemed to be modifications of this license.)
APPENDIX
Distribution of executable versions.
You may distribute covered code in executable form only if
the requirements of section 3.1-3.5 have been met for
that covered code, and if you include a notice stating that
the source code version of the covered code is available
under the terms of this license, including a description of
how and where you have fulfilled the obligations of section
3.2. The notice must be conspicuously included in any
notice in an executable version, related documentation or
collateral in which you describe recipients' rights relating
to the covered code. You may distribute the executable
version of covered code or ownership rights under a
license of your choice, which may contain terms different
from this license, provided that you are in compliance with
the terms of this license and that the license for the executable version does not attempt to limit or alter the recipient's rights in the source code version from the rights set
forth in this license. If you distribute the executable version under a different license you must make it absolutely
clear that any terms which differ from this license are
offered by you alone, not by the Initial developer or any
contributor. You hereby agree to indemnify the initial
developer and every contributor for any liability incurred
by the initial developer or such contributor as a result of
any such terms You offer.
Larger works.
You may create a larger work by combining covered code
with other code not governed by the terms of this license
and distribute the larger work as a single product. In such
a case, you must make sure the requirements of this
license are fulfilled for the covered code.
147
APPENDIX
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE
ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT
FOR A PARTICULAR PURPOSE OR NON-INFRINGING.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU.
SHOULD ANY COVERED CODE PROVE DEFECTIVE IN
ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR
ANY OTHER CONTRIBUTOR) ASSUME THE COST OF
ANY NECESSARY SERVICING, REPAIR OR CORRECTION.
THIS DISCLAIMER OF WARRANTY CONSTITUTES AN
ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY
COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT
UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1.
8.2.
APPENDIX
148
This license and the rights granted hereunder will terminate
automatically if you fail to comply with terms herein and
fail to cure such breach within 30 days of becoming aware
of the breach. All sublicenses to the covered code which
are properly granted shall survive any termination of this
license. Provisions which, by their nature, must remain in
effect beyond the termination of this license shall survive.
If you initiate litigation by asserting a patent infringement
claim (excluding declatory judgment actions) against initial developer or a contributor (the initial developer or
contributor against whom you file such action is referred
to as “Participant”) alleging that:
(a) such participant's contributor version directly or indirectly infringes any patent, then any and all rights
granted by such participant to you under sections 2.1
and/or 2.2 of this license shall, upon 60 days notice
from Participant terminate prospectively, unless if within
60 days after receipt of notice you either: (i) agree in
writing to pay participant a mutually agreeable reasonable
royalty for your past and future use of modifications
made by such participant, or (ii) withdraw your litigation
claim with respect to the contributor version against
such participant. If within 60 days of notice, a reasonable
royalty and payment arrangement are not mutually
agreed upon in writing by the parties or the litigation
claim is not withdrawn, the rights granted by participant to you under sections 2.1 and/or 2.2 automatically terminate at the expiration of the 60 day notice
period specified above.
(b) any software, hardware, or device, other than such participant's contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by
such participant under sections 2.1(b) and 2.2(b) are
revoked effective as of the date you first made, used,
sold, distributed, or had made, modifications made by
that participant.
8.3.
If you assert a patent infringement claim against participant alleging that such participant's contributor version
directly or indirectly infringes any patent where such claim
is resolved (such as by license or settlement) prior to the
initiation of patent infringement litigation, then the reasonable value of the licenses granted by such participant
under sections 2.1 or 2.2 shall be taken into account in
determining the amount or value of any payment or
license.
8.4.
In the event of termination under sections 8.1 or 8.2
above, all end user license agreements (excluding distributors
and resellers) which have been validly granted by you or
any distributor hereunder prior to termination shall survive
termination.
9. LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL
THEORY, WHETHER TORT (INCLUDING NEGLIGENCE),
CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL
DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF
ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,
WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE
BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY
TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT
APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT
APPLY TO YOU.
10. U.S. GOVERNMENT END USERS.
The covered code is a "commercial item," as that term is
defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
"commercial computer software" and "commercial computer
software documentation," as such terms are used in 48
C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.
12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4
(June 1995), all U.S. Government end users acquire covered code with only those rights set forth herein.
11. MISCELLANEOUS.
This license represents the complete agreement concerning
subject matter hereof. If any provision of this license is
held to be unenforceable, such provision shall be reformed
only to the extent necessary to make it enforceable. This
License shall be governed by California law provisions
(except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions. With
respect to disputes in which at least one party is a citizen
of, or an entity chartered or registered to do business in
the united states of america, any litigation relating to this
License shall be subject to the jurisdiction of the federal
courts of the northern district of california, with venue
lying in santa clara county, california, with the losing party
responsible for costs, including without limitation, court
costs and reasonable attorneys' fees and expenses. The
application of the united nations convention on contracts
for the International sale of goods is expressly excluded.
Any law or regulation which provides that the language of
a contract shall be construed against the drafter shall not
apply to this license.
EXHIBIT A -Mozilla Public License.
12. RESPONSIBILITY FOR CLAIMS.
As between initial developer and the contributors, each
party is responsible for claims and damages arising, directly
or indirectly, out of its utilization of rights under this
license and you agree to work with initial developer and
contributors to distribute such responsibility on an equitable
basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.
Alternatively, the contents of this file may be used under the
terms of the _____ license (the "[___] License"), in which case
the provisions of [______] license are applicable instead of those
above. If you wish to allow use of your version of this file only
under the terms of the [____] license and not to allow others to
use your version of this file under the MPL, indicate your decision
by deleting the provisions above and replace them with the
notice and other provisions required by the [___] license. If you
do not delete the provisions above, a recipient may use your version
of this file under either the MPL or the [___] license."
Software distributed under the license is distributed on an "AS
IS" basis, WITHOUT WARRANTY OF ANY KIND, either express
or implied. See the license for the specific language governing
rights and limitations under the License.
The Original Code is ______________________________________.
The
Initial
Developer
of
the
Original
Code
is___________________.
Portions created by ______________________ are Copyright (C)
_______________________. All Rights Reserved.
Contributor(s): ______________________________________.
NOTE: The text of this exhibit A may differ slightly from the text
of the notices in the source code files of the original code. You
should use the text of this exhibit A rather than the text found in
the original code/source code for Your modifications.
APPENDIX
13. MULTIPLE-LICENSED CODE.
Initial developer may designate portions of the covered
code as "Multiple-Licensed". "Multiple-Licensed" means
that the initial developer permits you to utilize portions of
the covered code under your choice of the NPL or the
alternative licenses, if any, specified by the initial developer
in the file described in exhibit A.
The contents of this file are subject to the Mozilla Public License
Version 1.1 (the “license”); you may not use this file except in
compliance with the License. You may obtain a copy of the
license at http://www.mozilla.org/MPL/
149
Download PDF

advertising