Sony | MHC-VX333 | Operating instructions | Clarion A300.2 Stereo Amplifier User Manual

4-234-628-12(1)
Mini Hi-Fi
Component
System
Operating Instructions
MHC-VX333/VX222
© 2001 Sony Corporation
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
To prevent fire, do not Cover the ventilation of the
apparatus with news papers, table-cloths, curtains,
etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
Don’t throw a battery, dispose it as the
injurious wastes.
This system can play the
following discs
VIDEO CDs
Contents
Audio + Video
Audio
(moving pictures)
Disc size
12 cm/8 cm
12 cm/8 cm
Play time
74 min./20 min.
74 min./20 min.
Note on VIDEO CDs
This system conforms to VIDEO CDs without PBC
functions (Ver. 1.1) and VIDEO CDs with PBC
functions (Ver. 2.0) of VIDEO CD standards. You
can enjoy two kinds of playback according to the disc
type.
Disc type
You can
VIDEO CDs
without PBC
functions (Ver.
1.1 discs)
Enjoy video playback (moving
pictures) as well as audio CDs.
VIDEO CDs
with PBC
functions (Ver.
2.0 discs)
Play interactive software using
menu screens displayed on the TV
screen (menu playback), in
addition to the video playback
function of VIDEO CDs without
PBC functions.
Moreover, you can play high or
standard quality still picture.
* PBC = Play Back Control
2
Audio CDs
Disc Logo
Table of Contents
Parts Identification
Main unit ............................................... 4
Remote Control ..................................... 5
Getting Started
Hooking up the system .......................... 6
Inserting two R6 (size AA) batteries into
the remote ........................................ 8
Setting the time ...................................... 9
Saving the power in standby mode ........ 9
CD/VIDEO CD
Loading a CD/VIDEO CD .................. 10
Playing a CD
— Normal Play/Shuffle Play/
Repeat Play ................................... 10
Programing CD tracks
— Program Play ............................ 11
Playing a VIDEO CD
— Normal Play/Shuffle Play/
Repeat Play ................................... 12
Playing a VIDEO CD with PBC
functions (Ver. 2.0)
— PBC Play .................................. 13
Using the CD display .......................... 14
Using the on-screen display ................ 15
Locating a specific part of a disc ......... 16
— Time Search/Disc Digest/Track
Digest
Resuming playback from the point you
stopped a VIDEO CD
— Resume Play ............................. 18
Adjusting the picture
— Picture Effect ............................ 18
Tuner
Presetting radio stations ....................... 19
Listening to the radio
— Preset Tuning ........................... 20
Tape
Loading a tape ..................................... 20
Playing a tape ...................................... 21
Recording to a tape
— CD Synchro Recording/Recording
Manually/Program Edit ................. 22
Timer-recording radio programs ......... 23
Sound Adjustment
Adjusting the sound ............................. 24
Selecting the sound effect .................... 24
Adjusting the graphic equalizer and
storing ............................................ 25
Selecting the surround effect ............... 26
Other Features
Enhancing video game sound
— Game Sync ............................... 26
Changing the spectrum analyzer
display ........................................... 26
Singing along: Karaoke ...................... 26
Falling asleep to music
— Sleep Timer .............................. 28
Waking up to music
— Daily Timer .............................. 28
Optional Components
Hooking up the optional A/V
components ................................... 29
Connecting a video game machine ...... 30
Additional Information
Precautions .......................................... 31
Troubleshooting ................................... 33
Messages ............................................. 35
Specifications ...................................... 35
Glossary ............................................... 37
3
Parts Identification
The items are arranged in alphabetical order. Refer to the pages indicated in parentheses for details.
Main unit
1 2 3 4 5 6 78
9 0 qa
qs
qd
ej
qf
qg
eh
qh
eg
qj
qk
ef
ed
ql
es
w;
ea
wa
e; wl wk wj
AUDIO jacks eg (30)
CD qd (10 – 13, 22, 23)
CD SYNC wg (22, 23)
Deck A ea (20, 21)
Deck B wa (20 – 24)
DIRECTION 8 (21 – 23, 27)
DISC 1 – 3 ws (10, 11, 13)
DISC SKIP EX-CHANGE ed
(10, 11, 13)
Disc tray 9 (10)
DISPLAY 8 (9, 14)
ECHO LEVEL control wk (27)
EDIT 8 (23)
EFFECT ON/OFF 4
(25, 27)
ENTER qa (9, 13, 14, 18, 19,
23 – 25, 28, 29, 35)
GAME ej (26, 30)
GAME EQ 2 (24, 26)
GROOVE 5 (24)
KARAOKE PON ef (27)
4
wh
wg wf wd ws
MD (VIDEO) qh (30)
MIC 1, 2 jack es (26, 27)
MIC LEVEL control wl (26, 27)
MOVIE EQ q; (24, 25)
MUSIC EQ 7 (24, 25)
P FILE qs (25)
PHONES jack ql
PICTURE EFFECT 3 (18)
PLAY MODE 8 (10 – 12)
REC PAUSE/START wf (22, 23)
REPEAT 8 (11)
SPECTRUM 8 (26)
STEREO/MONO 8 (20)
TAPE A/B qg (20, 22)
TUNER MEMORY 8 (19)
TUNER/BAND qf (19, 22)
VIDEO jack eh (30)
VOLUME control qj
BUTTON DESCRIPTIONS
?/1 (power) 1
v/V/b/B 6
Z OPEN/CLOSE qk
Z (deck B) w;
M (fast forward) wd
+ wd
. (go back) wh
> (go forward) wh
X (pause) wh
hH (play) wh
x (stop) wh
m (rewind) wj
– wj
Z (deck A) e;
Remote Control
ej
6
eh
eg
7
Parts Identification
1 2 345
8
9
ef
ed
es
ea
0
qa
qs
qd
e;
wl
wk
wj
qf
qg
qh
wh
wg
wf
qj
qk
ql
wd
ws
w;
wa
CD eh (10 – 13, 22, 23)
CINEMA SPACE wg (26)
CLEAR e; (12)
CLOCK/TIMER SELECT 2
(24, 29)
CLOCK/TIMER SET 3 (9, 23,
28, 29)
DISPLAY ed (9, 14)
D.SKIP qd (10, 11, 13)
EFFECT ON/OFF qj (25, 27)
ENTER wd (9, 13, 14, 18, 19,
23 – 25, 28, 29, 35)
GAME ef (26, 30)
GAME EQ ws (24, 26)
KARAOKE PON ea (27)
KEY CONTROL #/2 qh (27)
MD (VIDEO) eg (30)
MOVIE EQ qk (24, 25)
MUSIC EQ wf (24, 25)
NEXT wl (13, 14, 17)
Numeric buttons 0 (14, 16, 17,
18)
ON SCREEN qf (15)
P FILE w; (25)
PICTURE/EFFECT wh (18)
PRESET + qg (19)
PRESET – qg (19)
PREV wk (13, 14, 17)
REPEAT qa (11)
RETURN O wj (14)
SELECT qg (13, 14)
SLEEP 1 (28)
SPECIAL MENU qs (16, 17)
SPECTRUM es (26)
TAPE A/B 6 (20, 22)
TUNER/BAND ej (19, 22)
TUNING + qg (19, 20)
TUNING – qg (19, 20)
TV ?/1 4 (8)
TV CH +/– 8 (8)
TV/VIDEO 9 (8)
TV VOL +/– 7 (8)
VOL ql
BUTTON DESCRIPTIONS
?/1 (power) 5
M (fast forward) qg
. (go back) qg
> (go forward) qg
X (pause) qg
nN (play) qg
m (rewind) qg
x (stop) qg
v/V/b/B wa
5
Getting Started
Hooking up the system
Perform the following procedure 1 to 5 to hook up your system using the supplied cords and
accessories.
AM loop antenna
FM antenna
3
2
4
1
5
Left speaker
Right speaker
1 Connect the speakers.
2 Connect the FM/AM antennas.
Connect the speaker cords to the SPEAKER
jacks as shown below.
Set up the AM loop antenna, then connect
it.
Insert only the stripped portion.
R
+
L
+
Red/Solid
(3)
–
Jack type A
AM loop antenna
Extend the FM lead antenna
horizontally
FM
Black/Stripe (#)
75
AM
6
Jack type B
5 Connect the power cord to a wall outlet.
Extend the FM lead antenna
horizontally
AM loop antenna
L
AM
3 Connect the video input jack of your TV
to the VIDEO OUT jack with the
supplied video cable.
VIDEO
OUT
6 Set the color system to PAL or NTSC
depending on the color system of your
TV while the power is off.
The color system Press
of your TV
AUTO (factory
setting)
?/1 while holding down X.
If your TV automatically
changes the color system
according to the input signal,
the system is set to AUTO.
NTSC
?/1 while holding down
>. The system is set to
NTSC.
PAL
?/1 while holding down
.. The system is set to
PAL.
When using a TV
Turn on the TV and select the video input so
you can view the pictures from this system.
Tip
For even higher quality video images, you can use an
optional S-video cable to connect the S VIDEO input
jack on your TV to the S VIDEO OUT jack.
4 For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage.
Getting Started
FM
CO75
AX
IA
The demonstration appears in the display.
When you press ?/1, the system turns on
and the demonstration automatically ends.
If the supplied adapter on the plug does not
fit your wall outlet, detach it from the plug
(only for models equipped with an adapter).
Notes
• You cannot set the color system in the Power
Saving Mode.
• When you play back a VIDEO CD recorded in the
different color system from the one you set to the
unit, the picture image may be distorted.
To connect optional components
See page 29.
230 - 240V
220V
120V
continued
7
Hooking up the system (continued)
To attach the speaker pads
Attach the supplied speaker pads to the bottom
of the speakers to stabilize the speakers and
prevent them from slipping.
When carrying this system
Perform the following procedure to protect
the CD mechanism.
1 Make sure that all discs are removed
from the unit.
2 Hold down CD and then press ?/1 until
“STANDBY” appears.
When you release the buttons, “LOCK”
appears.
3 Unplug the AC power cord.
Note
Keep the speaker cords away from the antennas to
prevent noise.
Inserting two R6 (size AA)
batteries into the remote
Using the remote
You can use the buttons shown below to
operate a Sony TV.
To
Press
Turn the TV on or
off
TV ?/1.
Switch the TV’s
video input
TV/VIDEO.
Change the TV
channels
TV CH + or –.
Adjust the volume
of the TV
speaker(s)
TV VOL + or –.
e
E
E
e
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates the
system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage.
8
Setting the time
remote.
Press DISPLAY repeatedly when the
system is off.
Proceed to step 5 when “CLOCK” appears
in the display.
Each time you press the button, the system
switches cyclically as follows:
3 Press v or V repeatedly to select “SET
CLOCK”.
4 Press ENTER.
5 Press v or V repeatedly to set the hour.
6 Press B.
The minute indication flashes.
7 Press v or V repeatedly to set the
minute.
8 Press ENTER.
Tip
Demonstration t Clock display
t Power Saving Mode
Getting Started
1 Turn on the system.
2 Press CLOCK/TIMER SET on the
Saving the power in
standby mode
Tips
• ?/1 indicator lights up even in the Power Saving
Mode.
• The timer functions in the Power Saving Mode.
Note
You cannot set the time in the Power Saving Mode.
To cancel the Power Saving Mode
Press DISPLAY once to show the
demonstration or twice to show the clock
display.
If you made a mistake or want to change the time,
start over from step 2.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
9
CD/VIDEO CD
Loading a CD/VIDEO CD
1 Press CD.
2 Press PLAY MODE repeatedly until the
mode you want appears in the display.
1 Press Z OPEN/CLOSE.
The disc tray opens.
2 Place a CD or VIDEO CD with the label
side up on the disc tray.
When you play a CD
single (8 cm CD),
place it on the inner
circle of the tray.
To insert additional discs, press DISC SKIP
EX-CHANGE to rotate the disc tray.
Select
To play
ALL DISCS
(Normal Play)
All CDs in the disc tray
continuously.
1DISC
(Normal Play)
The CD you have selected
in original order.
SHUFFLE
ALL DISCS
(Shuffle Play)
The tracks on all CDs in
random order.
SHUFFLE
1DISC
(Shuffle Play)
The tracks on the CD you
have selected in random
order.
PROGRAM
(Program Play)
The tracks on all CDs in the
order you want them to be
played (see “Programing
CD tracks” on page 11).
3 Press Z OPEN/CLOSE to close the disc
tray.
3 Press hH (or nN on the remote).
Playing a CD
Other Operations
–– Normal Play/Shuffle Play/Repeat
Play
This system lets you play the CD in different
play modes.
Disc tray number
Disc presence
indicator
10
Track
number
To
Do this
Stop play
Press x.
Pause
Press X. Press again to resume
play.
Select a track
During play or pause, press >
(to go forward) or . (to go
back).
Find a point
in a track
During play, press M (to go
forward) or m (to go back). At
the desired point, press hH
(or nN on the remote) to stop
searching and start playback.
Select a CD in
stop mode
Press DISC 1 – 3 or DISC SKIP
EX-CHANGE (or D.SKIP on the
remote).
Playing time
To
Do this
Switch to CD
function from
another source
Press DISC 1 – 3 (Automatic
Source Selection). However, if a
CD is used in a program, play does
not start even if you press CD 1 –
3.
Press Z OPEN/CLOSE.
Exchange other
CDs while
playing
Press DISC SKIP EX-CHANGE.
Play repeatedly
(Repeat Play)
Press REPEAT during play until
“REPEAT” or “REPEAT 1”
appears.
REPEAT*1: For all the tracks on
the CD up to five times.
REPEAT 1*2: For a single track
only.
To cancel playing repeatedly, press
REPEAT until “REPEAT” or
“REPEAT 1” disappears.
–– Program Play
You can make a program of up to 32 tracks
from all the CDs in the order you want to play
them.
1 Press CD, then place a CD.
2 Press PLAY MODE repeatedly until
“PROGRAM” appears in the display.
3 Press one of DISC 1 – 3 to select a CD.
CD/VIDEO CD
Remove a CD
Programing CD tracks
To program all the tracks on a CD at once,
proceed to step 5 with “AL” displayed.
4 Press . or > until the desired
track appears in the display.
Disc tray number
Total playing time
(including selected track)
1
* You cannot select “REPEAT” and “SHUFFLE
ALL DISCS” at the same time.
*2 When you select “REPEAT 1”, that track is
repeated endlessly until REPEAT 1 is canceled.
Playing a track by entering the track
number
Press the number button(s) on the remote to
enter the track number of the track you want to
play.
To enter a track number over 10
1 Press >10.
2 Enter the corresponding digits.
To enter 0, press 10/0 instead.
Example:
To play track number 30, press >10, then 3 and
10/0.
Track number
5 Press ENTER.
The track is programed. The program step
number appears, followed by the total
playing time.
6 Program additional discs or tracks.
To program
Repeat steps
Other discs
3 and 5
Other tracks on the
same disc
4 and 5
Other tracks on other
discs
3 to 5
continued
11
Programing CD tracks (continued)
7 Press hH (or nN on the remote).
Playing a VIDEO CD
— Normal Play/Shuffle Play/Repeat
Play
Other operations
To
Do this
Cancel Program
Play
Press PLAY MODE repeatedly
until “PROGRAM” and
“SHUFFLE” disappear.
Clear a track from
the end
Press CLEAR on the remote in
stop mode.
Clear the entire
program
Press x once in stop mode or
twice during play.
Tips
• The program you made remains after Program Play
finishes. To play the same program again, press CD,
then press nN.
• “--.--” appears when the total CD program time
exceeds 100 minutes, or when you select a CD track
whose number is 21 or over.
You can play both VIDEO CDs without PBC
functions (Ver 1.1) and VIDEO CDs with PBC
functions (Ver. 2.0).
Disc tray number
Disc presence
indicator
Track number
Playing time
1 Turn on your TV and select the video
input.
Refer to the operating instructions supplied
with your TV if you need help.
2 Press CD.
3 Press PLAY MODE repeatedly until the
mode you want appears in the display.
Select
To play
ALL DISCS*1 All CDs in the disc tray
(Normal Play) continuously.
1DISC*1
(Normal Play)
The CD you have selected in
original order.
SHUFFLE
The tracks on all CDs in random
ALL DISCS*2 order.
(Shuffle Play)
SHUFFLE
1DISC*2
(Shuffle Play)
The tracks on the CD you have
selected in random order.
PROGRAM
The tracks on all CDs in the
(Program Play) order you want them to be
played (see “Programing CD
tracks” on page 11).
*1 Only for VIDEO CDs with PBC functions
(Ver.2.0), “PBC” appears while the PBC
function is set to on.
*2 Shuffle Play does not function during menu
playback of a VIDEO CD with PBC functions
(Ver. 2.0).
12
4 Press hH (or nN on the remote).
Other Operations
To
Do this
Stop play
Press x.
— PBC Play
1
Press X* . Press again to resume
playback.
Select a track
or scene*2
Press NEXT on the remote or >
to go forward, PREV on the
remote or . to go back. When
you play VIDEO CDs with PBC
functions (Ver 2.0), see pages 13
and 14).
1 Press and hold down m or
M during playback. According to
the length of holding down the
button, speed changes as follows:
1 (slow) t 2 (normal) t 3 (high)
Release m or M at the desired
speed and the search goes on at the
speed.
2 Press m or M during
playback. Each time you press the
button, speed changes cyclically as
follows:
1 (slow) t 2 (normal) t 3 (high)
At the desired point, press
hH (or nN on the remote)
to stop searching and start
playback.
Select a VIDEO
CD in stop
mode
Press DISC 1 – 3 or DISC SKIP
EX-CHANGE (or D.SKIP on the
remote).
Remove the
VIDEO CD
Press Z OPEN/CLOSE.
Exchange other
VIDEO CDs
while playing
Press DISC SKIP EX-CHANGE.
Play repeatedly
(Repeat Play)
See page 11.
You can use menus on your TV screen to enjoy
the disc’s interactive software.
The menu format and structure will differ with
each disc.
1 Press CD.
2 Press hH (or nN on the remote)
CD/VIDEO CD
Pause
Find a point in a
track or scene
(Lock Search
function)
Playing a VIDEO CD with
PBC functions (Ver. 2.0)
to start playing a VIDEO CD with PBC
functions (Ver. 2.0).
The VIDEO CD and PBC indicators light
up and a PBC menu appears on your TV.
• VCD: Lights during playback of a
VIDEO CD.
• PBC: Lights during PBC playback of a
PBC compatible VIDEO CD (Ver. 2.0).
• PBC OFF: Lights when a PBC
compatible VIDEO CD (Ver. 2.0) is
played without using the PBC functions
(see page 14).
3 Press . or > repeatedly to select a
number from the menu, then press
ENTER or SELECT.
4 Continue according to the instructions
on the menus to enjoy interactive
playback.
continued
*1 There may be some disturbance in the video
image.
*2 Only when setting the PBC function to off or when
playing VIDEO CDs without PBC functions (Ver.
1.1).
13
Playing a VIDEO CD with PBC
functions (Ver. 2.0) (continued)
Stop play
Press x.
You can check the remaining time of the
current track or the entire CD.
See the rest of
a menu
Press NEXT on the remote.
Press DISPLAY repeatedly.
Go back to the
top of a menu
Press PREV on the remote.
Go back to a
previous menu
Press RETURN O on the remote.
Cancel playback
with PBC
functions (Ver.
2.0)
In stop mode, press . or >
to select the desired track, then
press ENTER or SELECT on the
remote.
Also you can select the desired
track number using the numeric
buttons on the remote.
The PBC OFF indicator lights up
and playback begins from the
selected track.
Still images, such as the menu
screens, will not be shown.
To
Do this
Select a menu
number using
the remote
The display changes cyclically as follows:
During normal play
Press the numeric buttons (see “To
enter a track number over 10” on
page 11).
Tip
When
appears on the TV screen, you have
pressed an invalid button.
14
Using the CD display
Playing time of the current track t Remaining
time of the current track t Remaining time of
the current CD (1DISC mode) or “--.--” display
(ALL DISCS mode) t Clock display (for
eight seconds) t Effect status
(VIDEO CDs with PBC functions (Ver. 2.0))
Playing time on the current track* t Clock
display (for eight seconds) t Effect status
* May not appear with still images, etc.
In stop mode
Total number of tracks and total playing time
t Clock display (for eight seconds)
t Effect status
4
Using the on-screen
display
Displayed
In Program Play
mode
Programed disc and track
number
In stop mode (ON
SCREEN 2 only)
Disc number and track
numbers
In other conditions
No display
5
Press ON SCREEN on the remote.
While the deck is:
Displayed
Each time you press this button, the on-screen
display changes cyclically as follows:
In stop mode
STOP
During playback
Elapsed time of current track
ON SCREEN 1 t ON SCREEN 2 t ON
SCREEN OFF*
6
* No display (except for Time Search/Disc Digest/
Track Digest)
While the deck is:
Displayed
In stop mode
Current disc number and total
playing time of the current
disc*3
During playback
No display
ON SCREEN display 1, 2
1
2
3
RESUME
VCD
KARAOKE
DISC 1
CONTINUE
21
4
STOP
25 : 40
REPEAT
DISC 1
VCD
TR 1 – 12
DISC 2
VCD
TR 1 – 16
DISC 3
CD
TR 1 – 10
5
6
7
8
CD/VIDEO CD
You can check the current operating status and
disc information of VIDEO CDs or audio CDs
during playback or in stop mode. Depending
on conditions, some items are displayed and
others are not.
While the deck is:
*3 In Program Play mode, total playing time of the
program appears.
7“REPEAT”, “REPEAT 1” or no display
1
8Key control level or no display
While the deck is:
Displayed
In stop mode
“RESUME” or no display
During playback
Current disc and track
number*1
*1 For VIDEO CD, only ON SCREEN 2 displays the
current disc and track number during playback.
“SCENE” and the number is displayed during
playback of a VIDEO CD with PBC functions.
Note
Check to make sure that ON SCREEN OFF is
selected when recording a video signal played back
by this system onto a video tape, etc. Otherwise the
display information will also be recorded onto the
video tape.
continued
2KARAOKE effect status
3Play mode or “AUTO PBC”*2
*2 “AUTO PBC” appears for a VIDEO CD with PBC
functions.
15
Using the on-screen display
(continued)
To switch language of on-screen
display (Chinese model only)
You can switch the messages in the on-screen
display from Chinese to English.
1 Press SPECIAL MENU on the remote.
2 Press 4 on the remote.
The messages switch from Chinese to
English.
To switch back to Chinese messages, repeat
this operation.
Locating a specific part of
a disc
— Time Search/Disc Digest/Track
Digest
The TV screen must be ON to use these
functions. These functions cannot be used
during playback of VIDEO CDs with PBC
functions (Ver. 2.0). Use the remote.
To stop playback
Press x.
To enter 10 or over with the numeric
buttons
Press the numeric buttons on the remote (see
“To enter a track number over 10” on page 11).
To use VIDEO CDs with PBC
functions (Ver. 2.0)
See pages 13 and 14.
16
Locating by elapsed time
from the beginning of the
disc
— Time Search
1 Press SPECIAL MENU on the remote.
2 Press 1 on the remote to select
“1) TIME SEARCH.”
3 Press the numeric buttons (1 – 10/0) on
the remote to enter the time (in
minutes) for the section you want.
To enter 10 minutes: Press 1 c 10/0.
The selected elapsed time appears on the
TV screen.
To reenter the time: Press CLEAR, and then
press the numeric buttons again.
4 Press hH (or nN on the remote).
Playback starts from the selected time.
Locating the track you want
— Disc Digest
You can select the track you want by viewing
the first frame of each track. 9 different tracks
can be displayed on the TV screen at one time.
“2) DISC DIGEST”.
The first frame of tracks 1 through 9 on the
current disc are displayed.
The sound of the first three seconds of each
track on an audio CD plays, but there is no
sound when using a VIDEO CD.
3 Press the numeric buttons (1 – 10/0) on
the remote to select the track you want.
To display the next 9 tracks
Press NEXT on the remote. The first frame of
tracks 10 through 18 are displayed.
When there are more tracks in the disc, “>”
appears in the upper right corner of the TV
screen.
To display previous tracks, press PREV on the
remote.
To switch to the digest of another
disc during Disc Digest
Press D.SKIP during Disc Digest.
Note
The play mode automatically switches to
CONTINUE mode if you start Disc Digest during
Shuffle or Program Play.
— Track Digest
You can have the CD player divide a VIDEO
CD track into 9 different sections and display
the first scene of each section on the TV screen.
1 Press SPECIAL MENU on the remote.
2 Press 3 on the remote to select
“3) TRACK DIGEST”.
The current track is divided into 9 sections
and the first frame of each section is
displayed.
The sound of the first three seconds of each
track on an audio CD plays, but there is no
sound when using a VIDEO CD.
CD/VIDEO CD
1 Press SPECIAL MENU on the remote.
2 Press 2 on the remote to select
Locating a section within a
track
3 Press the numeric buttons (1 – 10/0) on
the remote to select the section you
want.
Playback starts from a point near the
selected frame.
To switch to the digest of another
track during Track Digest
Press PREV or NEXT on the remote during
Track Digest.
Notes
• Tracks less than 40 seconds long may be divided
into fewer than 9 sections.
• You cannot use this function during Shuffle Play or
Program Play.
17
Resuming playback from
the point you stopped a
VIDEO CD
— Resume Play
The unit memorizes the point where you
stopped the VIDEO CD so you can resume
from that point. Resume Play is not canceled
when you turn off the system.
Resume Play is not available for an audio CD.
1 While playing a VIDEO CD, press x to
stop playback.
“RESUME” appears on your TV screen.
If “RESUME” does not appear, Resume
Play is not available.
2 Press hH (or nN on the remote).
The player starts playback from the point
you stopped the VIDEO CD in step 1.
To view from the beginning of the
VIDEO CD
When “RESUME” appears in the display, press
x, then press hH (or nN on the
remote).
Notes
• Resume Play is not available in the Digest, Shuffle,
or Program Play modes.
• Depending on where you stopped the VIDEO CD,
the player may resume playback from a different
point.
• Resume Play is canceled when:
– you press the numeric buttons, PLAY MODE, x,
DISC SKIP EX-CHANGE (or D.SKIP on the
remote), SPECIAL MENU, or ./>.
– you remove the VIDEO CD.
– you unplug the system’s power cord.
18
Adjusting the picture
— Picture Effect
You can adjust the hue and sharpness of the
picture.
1 Press PICTURE EFFECT during
playback.
2 Press b or B repeatedly to adjust the
hue.
3 Press v or V repeatedly to adjust the
sharpness.
4 Press ENTER or PICTURE EFFECT.
Tip
The hue and sharpness can be adjusted in 11 steps
(from –5 to +5).
Tuner
Presetting radio stations
You can preset up to 20 stations for FM and 10
stations for AM.
1 Press TUNER/BAND repeatedly to
select “FM” or “AM”.
2 Press and hold + or – (or TUNING + or –
Start over from step 1. After step 3, press .
or > (or PRESET – or + on the remote)
repeatedly to select the preset number you want
to store the other station.
You can preset a new station in the selected
preset number.
To erase a preset station
1 Press and hold TUNER MEMORY until a
preset number appears in the display.
Scanning stops automatically when the
system tunes in a station. “TUNED” and
“STEREO” (for a stereo program) appear.
2 Press . or > (or PRESET – or + on
the remote) repeatedly to select the preset
number you want to erase.
3 Press TUNER MEMORY.
A preset number appears in the display.
The stations are stored from preset number
1.
Preset number
4 Press ENTER.
“COMPLETE” appears.
The station is stored.
5 Repeat steps 1 to 4 to store other
stations.
To tune in a station with a weak
signal
Press + or – (or TUNING + or – on the remote)
repeatedly in step 2 to tune in the station
manually.
CD/VIDEO CD/Tuner
on the remote) until the frequency
indication starts to change, then
release it.
To set another station to an existing
preset number
Select “ALL ERASE” when you want to
erase all the preset stations.
3
Press ENTER.
“COMPLETE” appears.
When you erase a preset number, the preset
number decreases by one and all preset
numbers following the erased one are
renumbered.
To change the AM tuning interval
(except for the Middle Eastern and
Philippine models)
The AM tuning interval is factory-set to 9 kHz
(10 kHz in some areas). To change the AM
tuning interval, tune in any AM station first,
then turn off the system. While holding down
ENTER, turn the system back on. When you
change the interval, all the AM preset stations
are erased. To reset the interval, repeat the
same procedure.
Tip
The preset stations are retained for half a day even if
you unplug the power cord or if a power failure
occurs.
Note
You cannot change the AM tuning interval in the
Power Saving Mode.
19
Tape
Listening to the radio
Loading a tape
— Preset Tuning
Preset radio stations in the tuner’s memory first
(see “Presetting radio stations” on page 19).
1 Press TUNER/BAND repeatedly to
select “FM” or “AM”.
2 Press . or > (or press PRESET –
or + on the remote) repeatedly to tune
in the desired preset station.
Preset number
Frequency*
* When only one station is preset, “ONE
PRESET” appears in the display.
To listen to non-preset radio stations
Use manual or automatic tuning in step 2.
For manual tuning, press + or – (or TUNING
+ or – on the remote) repeatedly. For automatic
tuning, press and hold + or – (or TUNING
+ or – on the remote).
Tips
• When an FM stereo program has static noise, press
STEREO/MONO repeatedly until “MONO”
appears. There will be no stereo effect, but the
reception will improve.
• To improve broadcast reception, adjust the supplied
antennas.
20
1 Press TAPE A/B repeatedly to select
deck A or B.
2 Press Z.
3 Insert a tape in deck A or B with the
side you want to play/record facing
forward.
With the side
you want to
play/record
facing forward.
To
Do this
Stop play
Press x.
You can use TYPE I (normal) tape.
Pause
Press X. Press again to
resume play.
1 Load a tape.
2 Press DIRECTION repeatedly to select
Fast-forward
or rewind
Press m or M.
Remove
the cassette
Press Z.
Playing a tape
g to play one side. Select j*1 to
play both sides.
To play both decks in succession, select
“RELAY” (Relay Play)*2.
3 Press hH (or nN on the remote).
Tape presence indicator
To go forward
Press > during playback when N lights in
the display.
“TAPE A (or TAPE B) >>> +1” appears.
Press . during playback when n lights in
the display.
“TAPE A*2 (or TAPE B) <<< +1” appears.
Tuner/Tape
Press hH (or nN on the remote)
again to play the reverse side*1. The tape
starts playing.
Searching for the beginning of the
current or the next track (AMS)*1
To go back
Reverse
indicator
Forward
indicator
*1 The deck stops automatically after repeating the
sequence five times. For MHC-VX222, deck A
doesn’t play the reverse side.
*2 Relay Play always follows this cyclic sequence up
to five times, then stops:
Deck A (front side) t Deck A (reverse side)
t Deck B (front side) t Deck B (reverse side)
Press . during playback when N lights in
the display.
“TAPE A (or TAPE B) <<< –1” appears.
Press > during playback when n lights in
the display.
“TAPE A*2 (or TAPE B) >>> –1” appears.
*1 AMS (Automatic Music Sensor)
*2 For MHC-VX222, deck A doesn’t play the reverse
side.
Tip
For MHC-VX222, after the playback of the front
side of deck A, deck B repeats the sequence five
times.
When a tape is inserted, corresponding forward/
reverse indicators light.
Note
The AMS function may not operate correctly under
the following circumstances:
– When the unrecorded space between songs is less
than 4 seconds long.
– When the system is placed near a television.
21
Recording to a tape
— CD Synchro Recording/Recording Manually/Program Edit
You can record from a CD, VIDEO CD, tape or radio. You can use TYPE I (normal) tapes. The
recording level is adjusted automatically.
Steps
Recording from a CD/VIDEO CD
(CD Synchro Recording)
1
2
3
Load a recordable tape into deck B.
4
Recording from a CD/VIDEO CD/tape/
radio manually
Press CD.
Press CD, TAPE A/B or TUNER/BAND.
Load the CD/VIDEO CD you want
to record.
Load the CD, VIDEO CD or tape, or tune
in the station you want to record.
Press CD SYNC.
Press REC PAUSE/START.
Deck B stands by for recording.
REC PAUSE/START button flashes.
5
Press DIRECTION repeatedly to select g to record on one side. Select j
(or RELAY) to record on both sides.
6
Press REC PAUSE/START.
To stop recording
Note
Press x.
You cannot listen to other sources while recording.
Tips
• If you want to record from the reverse side, press
TAPE A/B to select deck B after step 1. Press
hH (or nN on the remote) to start playback
of the reverse side, then press x to start recording.
The TAPE B reverse indicator lights up.
• When you record on both sides, be sure to start
from the front side. If you start from the reverse
side, recording stops at the end of the reverse side.
• For recording from the radio:
If noise is heard while recording from the radio,
move the respective antenna to reduce the noise.
22
Press REC PAUSE/START, and then start
playing the desired source.
Recording a CD by specifying
track order
11 Press DIRECTION repeatedly to select
— Program Edit
12 Press REC PAUSE/START.
When programing, make sure the playing times
for each side do not exceed the length of one
side of the tape.
1 Load a CD and load a recordable tape
into deck B.
2 Press CD.
3 Press PLAY MODE repeatedly until
4 Press one of DISC 1 – 3 to select a CD.
To program all the tracks on a CD at once,
proceed to step 5 with “AL” displayed.
5 Press . or > until the desired
track appears in the display.
6 Press ENTER.
The track is programed. The program step
number appears, followed by the total
playing time.
7 To program additional tracks, repeat
steps 4 to 6.
Skip step 4 to select tracks from the same
disc.
8 Press X to pause at the end of side A.
9 Repeat steps 5 and 6 for the same disc
or 4 to 6 for tracks from another disc to
program the remaining tracks to be
recorded on side B.
10 Press CD SYNC.
Deck B stands by to record in the direction
of the indication on hH (the right
indication lights to record on the forward
side and the left indicator lights to record on
the reverse side). The CD player stands by
for playback.
Recording starts.
Tip
To check the required tape length for recording a CD,
press EDIT until “EDIT” flashes after you have
loaded a CD and pressed CD. The required tape
length for the currently selected CD appears, followed
by the total playing time for side A and side B
respectively (Tape Select Edit).
Note
You cannot use Tape Select Edit for discs containing
over 20 tracks.
Tape
“PROGRAM” appears in the display.
g to record on one side. Select j
(or RELAY) to record on both sides.
Timer-recording radio
programs
You can record a preset radio station from a
specified time.
To timer-record, you must first preset the radio
station (see “Presetting radio stations” on page
19) and set the clock (see “Setting the time” on
page 9).
1 Tune in the preset radio station (see
“Listening to the radio” on page 20).
2 Press CLOCK/TIMER SET on the
remote.
“SET DAILY 1” appears.
3 Press v or V repeatedly to select “SET
REC”, then press ENTER.
“ON” appears and the hour indication
flashes in the display.
continued
23
Sound Adjustment
Timer-recording radio programs
(continued)
4 Set the time to start recording.
Press v or V repeatedly to set the hour,
then press B.
The minute indication starts flashing.
Press v or V repeatedly to set the minute,
then press ENTER.
5 Repeat step 4 to set the time to stop
recording.
The start time appears, followed by the stop
time, the preset radio station to be recorded
(e.g., “TUNER FM 5”), then the original
display appears.
6 Load a recordable tape into deck B.
7 Press ?/1 to turn off the system.
When the recording starts, the volume level
is set to minimum.
Other Operations
To
You can reinforce the bass and create a more
powerful sound.
The GROOVE setting is ideal for music
sources, and the V-GROOVE setting is ideal
for video sources (movies, VCDs).
Press GROOVE.
Each time you press the button, the display
changes cyclically as follows:
GROOVE ON* t V-GROOVE ON*
t GROOVE OFF
* The volume switches to power mode, the equalizer
curve changes, and the “GROOVE” indicator
lights up.
Selecting the sound effect
Selecting the effect from the music
menu
Do this
Check the setting Press CLOCK/TIMER SELECT
on the remote and press v or V
repeatedly to select “SEL REC”.
Then, press ENTER. To change
the setting, start over from step 1.
Cancel the timer Press CLOCK/TIMER SELECT
on the remote and press v or V
repeatedly to select “TIMER
OFF”, then press ENTER.
Notes
• If the system is on at the preset time, the recording
will not be made.
• When you use the Sleep Timer, Daily Timer and
Timer recording will not turn on the system until
the Sleep Timer turns it off.
24
Adjusting the sound
Press MUSIC EQ, MOVIE EQ or GAME EQ
repeatedly to select the preset you desire.
The preset name appears in the display.
See the chart “Sound effect options”.
To cancel the effect
Press EFFECT ON/OFF repeatedly until
“EFFECT OFF” appears in the display.
Adjusting the graphic
equalizer and storing
Sound effect options
“SURR” appears if you select an effect with
surround effects.
MUSIC EQ
Effect
ROCK
POP
JAZZ
DANCE
SOUL
ORIENTAL
Standard music sources
You can adjust the sound by raising or
lowering the levels of specific frequency
ranges, then store up to three personal files (P
FILE) in the memory.
Select the audio emphasis you want for your
basic sound first.
1 Press b or B repeatedly to select a
frequency band, then press v or V to
adjust the level.
Frequency band
Frequency level
Effect
ACTION
DRAMA
MUSICAL
Soundtracks and special listening
situations
2 Press and hold P FILE.
A personal file number appears in the
display.
GAME EQ
Effect
ADVENTURE
ARCADE
RACING
PlayStation 1, 2 and other video
game music sources
3 Press P FILE repeatedly to select
P FILE 1 – 3 where you want to store
the equalizer setting.
Tape/Sound Adjustment
MOVIE EQ
4 Press ENTER.
“COMPLETE” appears.
This setting is automatically stored as the
personal file you selected in step 3.
To
Press
Call up a
personal file
P FILE repeatedly to select the
desired personal file number.
Cancel a
personal file
EFFECT ON/OFF repeatedly
until “EFFECT OFF” appears in
the display.
25
Other Features
Selecting the surround
effect
Press CINEMA SPACE on the remote
repeatedly to turn the surround effect on
or off.
Each time you press the button, the display
changes as follows:
C.SPACE LOW* t C.SPACE MID* t
C.SPACE HIGH* t SURR ON (on) t
SURR OFF (off)
* CINEMA SPACE is the surround effect for movies.
Note
When you select other sound effects, the surround
effect will be canceled.
Enhancing video game
sound
— Game Sync
You need to connect a video game machine
(see “Connecting a video game machine” on
page 30).
Press GAME.
Tips
• In the standby mode, the system automatically turns
on.
• The GAME EQ (previously selected effect) is
automatically selected.
• These operations cannot be performed in the Power
Saving Mode.
Changing the spectrum
analyzer display
Press SPECTRUM.
Each time you press the button, the display
changes cyclically as follows:
PATTERN 1 t PATTERN 2 t PATTERN
3 t PATTERN OFF (No display)
Singing along: Karaoke
You can sing along by turning down the
singer’s voice. You need to connect an optional
microphone.
1 Turn MIC LEVEL to MIN to turn down
the microphone control level.
2 Connect an optional microphone to
MIC 1 or 2.
26
3 Press KARAOKE PON repeatedly to
obtain the karaoke effect you desire.
Each time you press the button, the display
changes cyclically as follows:
KARAOKE PON t MPX R*1 t MPX
L*1 t Effect status*2
*1 Only for CD or VCD.
*2 KARAOKE PON is canceled.
To sing karaoke of multiplex CD, select
“MPX R” or “MPX L”.
4 Start playing the music.
5 Adjust the microphone volume by
turning MIC LEVEL.
Notes
• With some songs, vocals may not be canceled when
you select “KARAOKE PON”.
• During KARAOKE PON, equalizer and surround
settings cannot be changed.
• If you press MUSIC EQ, MOVIE EQ, GAME EQ
or EFFECT ON/OFF or recall a sound effect, the
karaoke mode is canceled.
• The instrumental sound may be reduced as well as
the singer’s voice when the sound is recorded in
monaural.
• The singer’s voice may not be reduced when:
– only a few instruments are playing.
– a duet is being played.
– the source has strong echoes or chorus.
– the singer’s voice deviates from the center.
– the voice on the source is singing in high soprano
or tenor.
Do this
Use VIDEO
CDs
Turn on your TV and switch it to
the appropriate video input.
Mixing and recording sounds
Cancel karaoke
mode
Turn MIC LEVEL to MIN and
disconnect the microphone from
MIC 1 or 2, then press KARAOKE
PON repeatedly until “KARAOKE
PON”, “MPX R” or “MPX L”
disappears.
1 Do the procedure for “Singing along”
Adjust the
microphone
echo
Turn ECHO LEVEL to adjust the
echo effect. To cancel the echoing,
turn ECHO LEVEL to MIN.
When you want to record from TAPE A,
press TAPE A/B repeatedly until TAPE A
is selected.
Adjust the key
Press KEY CONTROL # or 2 on
the remote to suit your vocal
range.
You can adjust the key higher of
lower in 13 halftone steps (26 –
#6).
This function cannot be used with
the tape deck.
(steps 1 through 5). Then, load a
recordable tape in deck B.
2 Press the function button of the source
you want to record (e.g., CD).
3 Press REC PAUSE/START.
Deck B stands by for recording. The
indicator on REC PAUSE/START flashes.
4 Press DIRECTION repeatedly to select
g to record on one side. Select j
(or RELAY) to record on both sides.
Sound Adjustment/Other Features
To
5 Press REC PAUSE/START and then
press hH (or nN on the remote)
to start playing the source to be
recorded.
Start singing along with the music.
continued
27
Singing along: Karaoke (continued)
To stop recording
Press x.
Tips
• If acoustic feedback (howling) occurs, move the
microphone away from the speakers or change the
direction of the microphone.
• If you want to record your voice through the
microphone only, you can do so by selecting the
CD function and not playing a CD.
• When high level sound signals are input, the system
automatically adjusts the recording level to prevent
distortion of the recorded sound signal (Auto Level
Control function).
Falling asleep to music
— Sleep Timer
You can set the system to turn off after a
certain time, so that you can fall asleep to
music.
Press SLEEP on the remote.
Each time you press the button, the minute
display (the turn-off time) changes cyclically as
follows:
AUTO* t 90 t 80 t 70 t … t 10 t
OFF
* The system turns off when the current CD or tape
finishes playback (for up to 100 minutes).
Other Operations
28
To
Press
Check the
remaining time
SLEEP on the remote once.
Change the
time to turn off
SLEEP on the remote
repeatedly to select the time you
want.
Cancel the Sleep
Timer function
SLEEP on the remote
repeatedly until “SLEEP OFF”
appears.
Waking up to music
— Daily Timer
You can wake up to music at a preset time.
Make sure you have set the clock (see “Setting
the time” on page 9).
1 Prepare the music source you want to
play.
• CD: Load a CD. To start from a
specific track, make a program (see
“Programing CD tracks” on page 11).
• Tape: Load a tape with the side you
want to play facing forward.
• Radio: Tune in the preset station you
want (see “Listening to the radio” on
page 20).
2 Adjust the volume.
3 Press CLOCK/TIMER SET on the
remote.
“SET DAILY 1” appears.
4 Press v or V repeatedly to select
“DAILY 1 (or 2)”, then press ENTER.
“ON” appears and the hour indication
flashes.
5 Set the time to start playing.
Press v or V repeatedly to set the hour,
then press B.
The minute indication flashes.
Press v or V repeatedly to set the minute,
then press ENTER.
6 Repeat step 5 to set the time to stop
playing.
7 Press v or V repeatedly until the music
source you want appears.
The indication changes as follows:
t TUNER y CD PLAY T
t TAPE PLAY T
Optional Components
8 Press ENTER.
The type of timer (“DAILY 1” or
“DAILY 2”), followed by the start time,
stop time, and the music source appear, then
the original display appears.
9 Press ?/1
to turn off the system.
To
Do this
Check the setting
Press CLOCK/TIMER
SELECT on the remote and
press v or V repeatedly to
select the respective mode
(“DAILY 1” or “DAILY 2”),
then press ENTER.
Change the setting
Start over from step 1.
Cancel the timer
Press CLOCK/TIMER
SELECT on the remote and
press v or V repeatedly to
select “TIMER OFF”, then
press ENTER.
Hooking up the optional
A/V components
You can connect your MD deck or VCR to this
system.
To the digital input
jack of the MD deck
To the audio output of
the MD deck or VCR
The system turns on 15 seconds before the preset
time.
Notes
• You cannot activate DAILY 1 and DAILY 2 timer
at the same time.
• When you use the Sleep Timer, the Daily Timer
will not turn on the system until the Sleep Timer
turns it off.
• You cannot activate the Daily Timer and Timerrecording at the same time.
To the audio
input of the
MD deck or
VCR
To the S VIDEO
input of the VCR
To the video
input of the VCR
continued
Other Features/Optional Components
Tip
29
Hooking up the optional A/V
components (continued)
To
Do this
Make a digital
recording from
a CD to an MD
Connect an optional optical cable.
Make an analog
recording on an
MD
Connect an optional audio cable.
Make an analog
recording from a
VIDEO CD to a
video tape
Connect an optional audio cable
from the MD/VIDEO (AUDIO)
OUT jacks and the supplied video
cable (or optional S VIDEO cable)
from the VIDEO OUT (or S
VIDEO OUT) jack to your VCR.
Listen to the
connected MD
deck
Press MD (VIDEO).
Listen to the
connected VCR
Hold down MD (VIDEO) and
press ?/1 while the system is on.
This switches the “MD” function
to “VIDEO”. Once you enable the
“VIDEO” function, just press MD
(VIDEO).
Connecting a video game
machine
Connect the video output of the video game
machine to the VIDEO jack, and the audio
output to the AUDIO jacks on the front panel
of the system. Connect the VIDEO OUT jack
on the rear panel of the system to the video
input of a TV using the optional video cable.
To listen to the sound of the connected video
game machine, press GAME.
To the video output of the video game machine
Notes
• You cannot record from a VIDEO CD to an MD
digitally. When you record from a VIDEO CD to an
MD, make an analog recording on MD.
• If you cannot select “MD” when you press MD
(VIDEO), press ?/1 while holding down MD
(VIDEO) when the system is on. “VIDEO” will be
switched to “MD”. To return to “VIDEO”, do the
same procedure.
• Make sure to match the color of the plugs and the
connectors.
• When you connect a VIDEO CD deck, set to “MD”.
30
To the audio output of the video game machine
Additional Information
To the video input of a TV
Precautions
On operating voltage
Before operating the system, check that the operating
voltage of your system is identical with the voltage of
your local power supply.
On safety
Notes
On placement
• Place the system in a location with adequate
ventilation to prevent heat build up.
• Do not place the system in an inclined position.
• Do not place the system in locations where it is:
— Extremely hot or cold
— Dusty or dirty
— Very humid
— Subject to vibrations
— Subject to direct sunlight.
On heat buildup
• Although the unit heats up during operation, this is
not a malfunction.
• Place the unit in a location with adequate
ventilation to prevent heat build-up in the unit.
If you continuously use this unit at a large volume,
the cabinet temperature of the top, side and bottom
rises considerably. To avoid burning yourself, do not
touch the cabinet.
To prevent a malfunction, do not cover the ventilation
hole for the cooling fan.
continued
Optional Components/Additional Information
• The video game machine image may appear on the
TV screen even if the system is turned off.
• See “Selecting the sound effect” on page 24 for
video game sound effects.
• If you press GAME while the system is off, the
system turns on, the function switches to GAME,
and the equalizer also switches to the GAME EQ
(previously selected effect).
• If you press GAME while the system is on, the
function switches to GAME and the equalizer
automatically switches to the GAME EQ
(previously selected effect).
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• Unplug the system from the wall outlet (mains) if it
is not to be used for an extended period of time. To
disconnect the cord (mains lead), pull it out by the
plug. Never pull the cord itself.
• Should any solid object or liquid fall into the
component, unplug the system and have it checked
by qualified personnel before operating it any
further.
• The AC power cord must be changed only at a
qualified service shop.
31
Precautions (continued)
On operation
• If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player. Should this occur, the system will not
operate properly. Remove the CD and leave the
system turned on for about an hour until the
moisture evaporates.
• When you move the system, take out any discs.
If you have any questions or problems concerning
your stereo system, please consult your nearest Sony
dealer.
Notes on CDs
• Before playing, clean the CD with a cleaning cloth.
Wipe the CD from the center out.
• Do not use solvents.
• Do not expose the CD to direct sunlight or heat
sources.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this system. Attempting to
do so may damage the system. Do not use such
discs.
Note on CD-R playback
Discs recorded on CD-R drives may not be played
back because of scratches, dirt, recording condition or
the drive’s characteristics. Besides, the discs, which
are not yet finalized at the end of recording, cannot be
played back.
Cleaning the cabinet
Use a soft cloth slightly moistened with mild
detergent solution.
To save a tape permanently
To prevent a tape from being accidentally recorded
over, break off the cassette tab from side A or B as
illustrated. If you later want to reuse the tape for
recording, cover the broken tab with adhesive tape.
Tab of side B
Tab of side A
Break off the
cassette tab
of side A
Before placing a cassette in the tape
deck
Take up any slack in the tape. Otherwise the tape may
get entangled in the parts of the tape deck and become
damaged.
When using a tape longer than 90
minutes
The tape is very elastic. Do not change the tape
operations such as play, stop, and fast-winding
frequently. The tape may get entangled in the tape
deck.
Cleaning the tape heads
Clean the tape heads after every 10 hours of use.
Be sure to clean the tape heads before you start an
important recording or after playing an old tape. Use
a separately sold dry-type or wet-type cleaning
cassette. For details, refer to the instructions of the
cleaning cassette.
Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that
have contact with the tape every 20 to 30 hours of use
with a separately sold demagnetizing cassette. For
details, refer to the instructions of the demagnetizing
cassette.
32
Troubleshooting
If you have any problem using this system, use
the following check list.
First, check that the power cord is connected
firmly and the speakers are connected correctly
and firmly.
Should any problem persist, consult your
nearest Sony dealer.
The sound from the connected source is
distorted.
• If “VIDEO” appears in the display when you
press MD (VIDEO), switch the display to “MD”
(see “Hooking up the optional A/V components”
on page 29).
“0:00” (or “12:00 AM”) flashes in the display.
• A power interruption occurred. Set the clock and
timer settings again.
The timer does not function.
• Set the clock correctly.
General
The display starts flashing as soon as you plug
in the power cord even though you haven’t
turned on the system (see step 5 of “Hooking up
the system” on page 7).
• Press DISPLAY when the system is turned off.
The demonstration disappears.
The clock setting/radio presetting/timer is
canceled.
There is no sound.
• Turn VOLUME clockwise (or press VOL + on
the remote).
• The headphones are connected.
• Insert only the stripped portion of the speaker
cord into the SPEAKER jack. Inserting the vinyl
portion of the speaker cord will obstruct the
speaker connections.
• There is no audio output during timer recording.
There is severe hum or noise.
• A TV or VCR is placed too close to the stereo
system. Move the stereo system away from the
TV or VCR.
• Set the timer correctly.
• Set the clock.
The remote does not function.
• There is an obstacle between the remote and the
system.
• The remote is not pointing in the direction of the
system’s sensor.
• The batteries have run down. Replace the
batteries.
There is acoustic feedback.
• Reduce the volume.
• Move the microphone away from the speakers or
change the direction of the microphone.
The color irregularity on a TV screen persists.
• Turn off the TV set once, then turn it on after 15
to 30 minutes. If the color irregularity still
persists, place the speakers farther away from the
TV set.
“PROTECT” and “PUSH POWER” appear
alternately.
Additional Information
• The power cord is disconnected or a power
failure occurs for longer than half a day.
Redo the following:
— “Setting the time” on page 9
— “Presetting radio stations” on page 19
If you have set the timer, also redo “Waking up
to music” on page 28 and “Timer-recording radio
programs” on page 23.
“DAILY 1”,“DAILY 2”, and “REC” do not appear
when you press CLOCK/TIMER SET.
• A strong signal was input. Press ?/1 to turn off
the system, leave the system turned off for a
while, then press ?/1 again to turn on the
system. If “PROTECT” and “PUSH POWER”
appear alternately even after the system is turned
on again, press ?/1 to turn off the system and
check the speaker cord.
continued
33
Troubleshooting (continued)
Tape Deck
The tape does not record.
Speakers
Sound comes from one channel or unbalanced
left and right volume.
• Check the speaker connection and speaker
placement.
Sound lacks bass.
• Check that the speaker’s + and – jacks are
connected correctly.
• No tape in the cassette holder.
• The tab has been removed from the cassette (see
“To save a tape permanently” on page 32).
• The tape has reeled to the end.
The tape does not record nor play or there is a
decrease in sound level.
• The heads are dirty (see “Cleaning the tape
heads” on page 32).
• The record/playback heads are magnetized (see
“Demagnetizing the tape heads” on page 32).
The tape does not erase completely.
CD/VIDEO CD Player
There is no picture.
• Check that the player is connected securely.
• Make sure you operate the TV correctly.
• Make sure you set the color system correctly,
according to your TV (color) system.
• Press CD.
The CD tray does not close.
• The CD is not placed properly.
• The record/playback heads are magnetized (see
“Demagnetizing the tape heads” on page 32).
There is excessive wow or flutter, or the sound
drops out.
• The capstans or pinch rollers are dirty (see
“Cleaning the tape heads” on page 32).
Noise increases or the high frequencies are
erased.
• The record/playback heads are magnetized (see
“Demagnetizing the tape heads” on page 32).
The CD will not play.
•
•
•
•
The CD is not lying flat in the disc tray.
The CD is dirty.
The CD is loaded label side down.
There is moisture on the CD.
Play does not start from the first track.
• The player is in program or shuffle mode. Press
PLAY MODE repeatedly until “PROGRAM” or
“SHUFFLE” disappears.
Tuner
There is severe hum or noise (“TUNED” or
“STEREO” flashes in the display).
• Adjust the antenna.
• The signal strength is too weak. Connect the
external antenna.
A stereo FM program cannot be received in
stereo.
• Press STEREO/MONO so that “STEREO”
appears.
34
If other troubles not described above
occur, reset the system as follows:
1 Unplug the power cord.
2 Plug the power cord back in.
3 Press x, ENTER, and ?/1 at the same
time.
4 Press ?/1 to turn on the system.
The system is reset to the factory settings. All
the settings you made are cleared.
Messages
One of the following messages may appear or
flash in the display during operation.
NO DISC
• There is no CD on the disc tray.
OVER
• You have reached the end of the CD.
Specifications
Amplifier section
MHC-VX333
The following measured at AC 120, 220, 240 V
50/60 Hz
DIN power output (rated) 100 + 100 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
120 + 120 watts (6 ohms
at 1 kHz, 10% THD)
MHC-VX222
The following measured at AC 120, 220, 240 V
50/60 Hz
DIN power output (rated) 50 + 50 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
60 + 60 watts (6 ohms at
1 kHz, 10% THD)
Additional Information
Inputs
MD/VIDEO (AUDIO) IN (phono jacks):
voltage 450/250 mV,
impedance 47 kilohms
GAME (AUDIO) IN (phono jack):
voltage 450 mV,
impedance 47 kilohms
MIC 1/2 (mini jack):
sensitivity 1 mV,
impedance 10 kilohms
Outputs
MD/VIDEO (AUDIO) OUT (phono jacks):
voltage 250 mV
impedance 1 kilohms
VIDEO OUT (phono jack):
max. output level
1Vp-p, unbalanced, Sync
negative, load impedance
75 ohms
S-VIDEO OUT (4-pin/mini-DIN jack):
Y: 1Vp-p, unbalanced,
Sync negative,
C: 0.286Vp-p,
load impedance 75 ohms
PHONES (stereo mini jack):
accepts headphones of
8 ohms or more
SPEAKER:
accepts impedance of 6 to
16 ohms
continued
35
Specification (continued)
CD/VIDEO CD player section
System
Laser
Wavelength
Frequency response
Signal-to-noise ratio
Dynamic range
Video color system format
Compact disc and digital
audio and video system
Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
780 – 790 nm
2 Hz – 20 kHz (±0.5 dB)
More than 90 dB
More than 90 dB
NTSC, PAL
CD OPTICAL DIGITAL OUT
(Square optical connector jack, rear panel)
Wavelength
660 nm
Output Level
–18 dBm
Tape deck section
Recording system
Frequency response
Wow and flutter
4-track 2-channel stereo
40 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassette
±0.15% W.Peak (IEC)
0.1% W.RMS (NAB)
±0.2% W.Peak (DIN)
Speaker
SS-VX333 for MHC-VX333
Speaker system
3-way, 3-unit,
bass-reflex type
Speaker units
Sub Woofer:
13 cm, cone type
Woofer:
13 cm, cone type
Tweeter:
5 cm, cone type
Nominal impedance
6 ohms
Dimensions (w/h/d)
Approx. 215 × 325 × 277 mm
Mass
Approx. 4.3 kg net per
speaker
SS-VX222 for MHC-VX222
Speaker system
2-way, bass-reflex type
Speaker units
Woofer:
13 cm, cone type
Tweeter:
5 cm, cone type
Nominal impedance
6 ohms
Dimensions (w/h/d)
Approx. 200 × 325 × 223 mm
Mass
Approx. 3.4 kg net per
speaker
General
Power requirements
Thai model:
Other models:
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Tourist model:
Other models:
Antenna
Antenna terminals
Intermediate frequency
76.0 – 108.0 MHz
87.5 – 108.0 MHz
FM lead antenna
75 ohm unbalanced
10.7 MHz
AM tuner section
Tuning range
Middle Eastern and Philippine models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
Other models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
530 – 1,710 kHz (with the
interval set at 10 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
36
220 V AC, 50/60 Hz
120 V, 220 V or
230 – 240 V AC,
50/60 Hz
Adjustable with voltage
selector
Power consumption
MHC-VX333:
MHC-VX222:
190 watts
120 watts
Dimensions (w/h/d)
MHC-VX333/VX222:
Approx. 280 × 325 × 421 mm
Mass
HCD-VX333:
HCD-VX222:
Approx. 10.5 kg
Approx. 9.0 kg
Supplied accessories:
AM loop antenna (1)
Remote Commander (1)
Batteries (2)
FM lead antenna (1)
Speaker pads (8)
Video cable (1)
Design and specifications are subject to change
without notice.
Glossary
Auto Pause
An automatical pauses according to the signal
encoded on the disc while playing a VIDEO
CD. If the CD player does not resume play for
a long time, press hH (or nN on the
remote) to resume play manually.
Menu Playback
Playback using the menu screens recorded on
VIDEO CDs with PBC functions. You can
enjoy simple interactive software using the
menu playback function.
Playback Control (PBC)
Signals encoded on VIDEO CDs (Version 2.0)
to control playback.
By using menu screens recorded on VIDEO
CDs with PBC functions, you can enjoy
playing simple interactive software, software
with search functions, and so on.
Track
Sections of a picture or a music piece on disc.
Each track is assigned a track number to help
you locate the track you want.
A compact disc which contains moving
pictures.
VIDEO CDs contain compact picture
information using the MPEG 1 format, one of
the world wide standards of digital compact
technology. The picture information is
compressed about 120 times. Consequently, a
12 cm VIDEO CD can contain up to 74
minutes of moving pictures.
VIDEO CDs also contain compact audio
information. Sounds outside the range of
human hearing are compressed while the
sounds we can hear are not compressed.
VIDEO CDs can hold six times the audio
information of conventional audio CDs.
There are two versions for VIDEO CDs:
Version 1.1 (VIDEO CDs without PBC
functions):
You can play only moving pictures and sounds.
Version 2.0 (VIDEO CDs with PBC functions):
You can play still pictures and enjoy PBC
functions.
This player can play both versions.
Additional Information
When you select a VIDEO CD with PBC
functions on this player, the PBC indicator
lights up.
VIDEO CD
37
Sony Corporation
Printed in Indonesia
Download PDF

advertising