Owner`s manual | Clarion FZ709E Bluetooth Headset User Manual

Owner’s manual
Mode d’emploi
Bedienungsanleitung
Istruzioni per l’uso
Gebruiksaanwijzing
Manual de instrucciones
Bruksanvisning
Manual de instruções
Bluetooth® USB/MP3/WMA/AAC RECEIVER
RÉCEPTEUR Bluetooth® USB/MP3/WMA/AAC
Bluetooth® USB/MP3/WMA/AAC EMPFÄNGER
RICEVITORE Bluetooth® USB/MP3/WMA/AAC
Bluetooth® USB/MP3/WMA/AAC RECEIVER
RECEPTOR DE Bluetooth® USB/MP3/WMA/AAC
Bluetooth® USB/MP3/WMA/AAC-RECEIVER
RECEPTOR DE Bluetooth® USB/MP3/WMA/AAC
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2009: Clarion Co., Ltd.
Printed in Malaysia / Imprimé en Malaisie / Gedruckt in Malaysia / Stampato in Malaysia
Gedrukt in Maleisi / Impreso en Malasia / Tryckt i Malaysia / Impresso na Malásia
PE-8501E
280-8841-00
English
English
Français
Thank you for purchasing this Clarion product.
∗ Please read this owner’s manual in its entirety before
operating this equipment.
∗ After reading this manual, be sure to keep it in a
handy place (e.g., glove compartment).
∗ Check the contents of the enclosed warranty card
and keep it carefully with this manual.
Français
Deutsch
Italiano
Nous vous remercions pour l’achat de ce produit
Clarion.
∗ Veuillez lire ce mode d’emploi dans son intégralité
avant d’utiliser cet équipement.
∗ Après l’avoir lu, veillez à conserver ce mode
d’emploi dans un endroit pratique (par ex. boîte à
gants).
∗ Vérifiez le contenu de la carte de garantie jointe
et conservez-la soigneusement avec ce mode
d’emploi.
Deutsch
Nederlands Español
Wir möchten Ihnen für den Kauf dieses Clarion
Produkts danken.
∗ Für optimale Leistung und Sicherheit lesen Sie bitte
diese Bedienungsanleitung aufmerksam durch.
∗ Heben Sie diese Anleitung auf, um sie später zum
Nach-schlagen griffbereit zu haben, (z.B. im Handschuhfach).
∗ Überprüfen Sie den Inhalt mit der beiliegenden
Garantiekarte. Legen Sie diese Karte zum Handbuch.
Italiano
Svenska Português
Grazie per aver acquistato questo prodotto Clarion.
∗ Si prega di leggere questo manuale utente prima di
utilizzare l’impianto.
∗ Una volta letto, conservare il manuale in un luogo
a portata di mano (ad es. il vano portaoggetti).
∗ Verificare il contenuto della garanzia acclusa e
conser-varla insieme a questo manuale.
Nederlands
Hartelijk bedankt voor de aankoop van dit Clarionproduct.
∗ Lees a.u.b. deze gebruiksaanwijzing compleet door,
alvorens dit apparaat in gebruik te nemen.
∗ Bewaar deze gebruiksaanwijzing, nadat u ze
gelezen hebt, op een gemakkelijke plaats (bv. in
het dashboardkastje).
∗ Lees wat in de bijgesloten garantiekaart staat en
bewaar ze samen met deze gebruiksaanwijzing.
Español
Gracias por haber adquirido este producto Clarion.
∗ Lea este manual de instrucciones por entero antes
de utilizar este equipo.
∗ Después de leer el manual, guárdelo a mano (por
ejemplo, en la guantera).
∗ Compruebe el contenido de la tarjeta de garantía
adjunta y guárdela cuidadosamente con este
manual.
Svenska
Tack för ditt val av denna Clarion-produkt.
∗ Var god läs denna manual i sin helhet innan du
använ-der denna utrustning.
∗ Efter att du läst denna manual, se till att förvara den
på ett praktiskt ställe (t.ex. handskfacket).
∗ Kontrollera innehållet på det medföljande garantikortet och förvara det aktsamt tillsammans med denna
manual.
Português:
Obrigado por comprar este produto Clarion.
∗ Por favor leia este manual do utilizador na sua totalidade antes de colocar o equipamento a funcionar.
∗ Após ler este manual, assegure-se que o tem à mão
(e.x., porta-luvas).
∗ Verifique os conteúdos do cartão de garantia
incluído e mantenha-o cuidadosamente com este
manual.
Dichiarazione di conformità:
Io mandatario nell’ UE: Clarion Europe S.A.S. Z.I. du Pré à Varois,
Route de Pompey, 54670 Custines, FRANCE
Dichiaro che il prodotto FZ709E è conforme al DM 28-08-1995 ottemperando
alle prescrizioni dei DM 25-06-1985 e DM 27-08-1987.
2
FZ709E
Title display
Trick Play indication
USB
Scan play
Repeat play
Random play
All scan play
All repeat play
All random play
iPod
Repeat/Random play
Repeat/All Random play
Random play
All Random play
Radio mode
USB mode
Band/Frequency/Preset no.
Mode name/Folder no./
Track no./Playback time
Mode name/Track no./
Playback time (iPod mode)
Previous layer/Current item
Adjust mode
BT Audio mode
Telephone mode
AUX mode
Clock time
Operation
status
indication
Function display
MP3 indication
WMA indication
AAC indication
Source icon
Radio mode
Stereo indication
Manual indication
Auto store indication
Scan indication
1. PRECAUTIONS .............................................................................................................................. 4
2. CONTROLS .................................................................................................................................... 5
MAIN UNIT ...................................................................................................................................... 5
3. NOMENCLATURE .......................................................................................................................... 6
Names of the Keys and Their Functions ......................................................................................... 6
Slider's Key Operation .................................................................................................................... 7
Display Items ................................................................................................................................... 8
OEL Display ..................................................................................................................................... 8
4. REMOTE CONTROL ...................................................................................................................... 9
Inserting the Battery ......................................................................................................................... 9
Functions of Remote Control Unit Buttons .................................................................................... 10
5. OPERATIONS ................................................................................................................................11
Basic Operations ............................................................................................................................11
Radio Mode Operations ................................................................................................................ 16
Radio Data System Operations ..................................................................................................... 19
USB Operations ............................................................................................................................ 23
iPod® Operations ............................................................................................................................ 27
Bluetooth® Operations ................................................................................................................... 31
Common Operations ..................................................................................................................... 35
6. TROUBLESHOOTING .................................................................................................................. 39
7. ERROR DISPLAYS ...................................................................................................................... 42
8. SPECIFICATIONS ........................................................................................................................ 43
1. This unit is applicable for on-road 4 wheel
vehicle purpose only. Use for tractor, fork
truck, bulldozer, off road vehicle, 2 or 3 wheel
motor bicycle, marine boat or other special
purpose vehicle is not appropriate.
2. In extreme cold, the screen movement may
slow down and the screen may darken, but
this is normal.The screen will recover when
it returns to normal temperature.
3. This unit is a Capacitive Touch-Sensing
product. The keys can be activated by finger
capacitance.
Using a thick glove may reduce the finger
capacitance and cannot operate the unit.
4. User is advised to have minimum operation
on the unit while driving. Drive safely.
BBE MP (Minimized Polynomial Non-Linear Saturation) Process improves digitally compressed sound, such as MP3, by
restoring and enhancing the harmonics lost through compression. BBE MP works by regenerating harmonics from the
source material, effectively recovering warmth, details and nuance.
Sound mode
MAGNA BASS EX indication
Beat EQ indication
MUTE indication
Manufactured under license from BBE Sound, Inc.
Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol
are registered trademarks of BBE Sound, Inc.
Radio Data System
Alternative frequency indication
Regional indication
Traffic announcement indication
Traffic programme indication
Programme type indication
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
iPod and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.
Windows Media™, and the Windows® logo are trademarks, or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
The use of apparatus in moderate climates.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Clarion Co.,Ltd.
is under license. Other trademarks and trade names are those of their respective owners.
®
The organic electro-luminescence display (OEL Display) of this product is made by high technology
basis.
However, it is possible that there might be part of the pixels which is always lighting or not lightning.
Sometimes unevenness of color and brightness might be occurred depend on the point of view to watch
in a characteristic.
A descending line across the screen will be displayed regularly to prevent OEL Display burn-in.
Please note that these are not hardware/software failures as it happens to be the structure of the organic
electro-luminescence display.
FZ709E
1. PRECAUTIONS
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY.
Mobile phone’s network signal
indication
Mobile phone’s battery
indication
Bluetooth® connection indication
OEL Screen
8
English
English
Contents
Display Items
FZ709E
3
4
®
Be sure to unfold and read the next page. / Veuillez déplier et vous référer à la page suivante.
Bitte ausbreiten und die nächste Seite lesen. / Assicurarsi di aprire e leggere la pagina successiva.
Volgende pagina uitvouwen en doorlezen a.u.b. / Cerciórese de desplegar y de leer la página siguiente.
Glöm inte att vika ut och läsa nästa sida. / Não deixe de abrir e ler a próxima página.
FZ709E
Slider’s Key Operation
3. NOMENCLATURE
Note:
Be sure to read this chapter referring to the front diagrams of chapter “2. CONTROLS” on page 5.
English
Français
Deutsch
MAIN UNIT / APPAREIL PRINCIPAL / HAUPTGERÄT
/ APPARECCHIO PRINCIPALE / HOOFDTOESTEL
/ UNIDAD PRINCIPAL / HUVUDENHET / UNIDADE PRINCIPAL
English
English
2. CONTROLS/ LES COMMANDES/
REGLER/ CONTROLLI/
REGELAARS/ CONTROLES/
KONTROLLER/ CONTROLOS
Slide
Names of the Keys and Their Functions
[
] key
Touch and hold the key for 1 second or longer
to turn off the power.
Switch to Source menu.
[
] key
To u c h t h e k e y t o s e t t h e TA ( Tr a ff i c
Announcement) standby mode.
[
] key
Switch to ADJ menu.
Italiano
[
Nederlands Español
[
[
] key
Switch Title display.
Touch and hold the key for 1 second or longer
to switch the display layout (Title mode
Indicator mode Clock).
] / [ ] key
Seek a station while in the Radio mode.
Select a track while in the USB mode.
Touch and hold the key for 1 second or longer to
enter the Fast-forward or Fast backward mode
while in USB mode.
Svenska Português
] key
Switch the band, or seek tuning or manual tuning
while in the Radio mode.
Switch to List Search, or Top folder while in the
USB mode.
Switch between last menu level and Play
display, or Top iPod menu while in the iPod
mode.
[
] key
Play or pause a track while in the USB mode.
Toggle Mute on/off while in the Radio mode.
Touch and hold the key for 2 seconds or longer
to memory new value during setting mode.
Dial the selected phone number thorugh call
method.
[
] slider
Adjust the volume.
[
] slider
Select a station while in the Radio mode.
Select the folder while in the USB mode.
End a call or reject an incoming call.
This key is used to make various settings.
USB PORT
USB memory device insertion port (at rear
panel).
AUX input
The input jack for connecting an external device
(at rear panel).
]
Touch & hold slider [
will increase volume continuously.
Touch & hold [ ] will to
scroll up items continuously.
Touch and release [ ]
once will increase the
volume 1 step.
Touch and release [ ]
once will scroll up items
1 step.
]
Touch & hold slider [
will decrease volume continuously.
Touch & hold [ ] will to
scroll down items continuously.
Touch and release [ ]
once will decrease the
volume 1 step.
Touch and release [ ]
once will scroll down items
1 step.
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Hinweis: Bitte diese Seite ausfalten und beim Lesen der einzelnen Kapital die Frontdiagramme beachten.
Nota: Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo.
Opmerking: Vouw deze pagina uit en zie tevens de afbeeldingen van het voorpaneel tijdens het doorlezen van de volgende hoofdstukken.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
Observera: Vik ut denna sida för att kunna se figurerna över bilstereons framsida medan du läser de olika kapitlen.
Nota: Certifique-se de abrir esta página e consulte os diagramas frontais conforme realiza a leitura de cada capítulo.
5
FZ709E
6
FZ709E
FZ709E
7
English
4. REMOTE CONTROL
Inserting the Battery
1. Turn over the remote control unit and slide the
cover in the direction indicated by the arrow in
the illustration.
2. Insert the battery (CR2025) into the insertion
guides, with the printed side (+) facing
upwards.
3. Press the battery in the direction indicated by the
arrow so that it slides into the compartment.
4. Replace the cover and slide in until it clicks
into place.
Notes:
Misuse may result in rupture of the battery, producing
leakage of fluid and resulting in personal injury or
damage to surrounding materials. Always follow these
safety precautions:
Use only the designated battery.
When replacing the battery, insert properly, with
+/- polarities oriented correctly.
Do not subject battery to heat, or dispose of in fire or
water. Do not attempt to disassemble the battery.
Dispose of used batteries properly.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
FZ709E
9
English
Functions of Remote Control Unit Buttons
Mode
Button
Radio
(Radio Data System)
USB
iPod
[SRC]
Switch among radio, USB, BT Audio, AUX and iPod.
[BND]
Switch reception
band.
[ ],[ ]
[
down.
Move tracks up and down.
Press and hold the button for 1 second or
longer: Fast-forward/fast-backward.
No function.
Switch between playback and pause.
] channels up and
]
[MUTE]
[TA]
[DISP]
iPod menu
No function.
Move tracks
up and
down.
No function.
No function.
Turn mute on and off.
TA on and off.
No function.
Switch among title display.
No function.
Press and hold for 1 second or longer: Switch among title display, indicator display and
clock display.
Scan play.
Press and hold the
button for 1 second
or longer to perform
folder scan play.
No function.
[PS/AS]
Preset scan.
Press and hold
the button for 2
seconds or longer:
Auto store.
Repeat play.
Press and hold the
button for 1 second
or longer to perform
folder repeat play.
Toggle repeat on/off. No function.
[AF]
AF function on and
off.
Press and hold the
button for 1 second
or longer: REG
function on and off.
PTY mode on and
off.
Random play.
Press and hold the
button for 1 second
or longer to perform
folder random play.
Random play.
Press and hold
the button for 1
second or longer
to perform folder
random play.
[PTY]
AUX
Increase and decrease volume (in all modes).
Move preset
],[
[
Play the first track.
Top play.
BT Audio
No function.
No function.
∗ Some of the corresponding buttons on the main unit and remote control unit have different functions.
∗ TV/VTR is not supported in this model.
10
FZ709E
Basic Operations
! CAUTION
Be sure to lower the volume before switching
off the unit power or the ignition key. The
unit remembers its last volume setting. If
you switch the power off with the volume
up, when you switch the power back on, the
sudden loud volume may hurt your hearing
and damage the unit.
Please operate this unit by the finger. It is not
possible to operate it normally with gloves
worn.
Turning on/off the power
Note:
Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Touch and hold any key for 2 seconds or longer
to power on the unit.
2. The unit automatically remembers its last
Operation mode and will automatically switch
to display that mode.
] key for 1 second or
3. Touch and hold the [
longer to turn off the power for the unit.
Note:
System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, the “SYSTEM CHECK” appears in the
display. This unit will switch to Radio mode after
system check.
Note: Be sure to read this chapter referring to the
front diagrams of chapter “2. CONTROLS” on
page 5.
English
5. OPERATIONS
3. There are 4 selections in the Source menu:
∗ iPod can connect to this unit via USB SLOT.
Adjusting the volume
] or touch the [ ] key
1. Slide up along the [
to increases the volume.
] or touch the [ ]
2. Slide down along the [
key to decreases the volume.
∗ The volume level is from 0 (minimum) to 33
(maximum).
Switching the title display
] key to switch the title display.
1. Touch the [
] key, the display
2. Each time you touch the [
switches in the following order:
Tuner/AUX/BT
No Title display.
iPod mode
TRACK (ALBUM)
ARTIST (TRACK)
USB mode
ALBUM (TRACK)
ARTIST (TRACK)
FOLDER (TITLE)
mode
ALBUM (ARTIST)
TRACK (ALBUM)
ARTIST (TITLE)
FOLDER (TRACK)
ALBUM (TRACK)
Selecting a mode
] key to switch to Source menu.
1. Touch the [
2. Touch the corresponding key beside the Source
mode name to enter into desired mode.
FZ709E
11
English
Basic Operations
∗ Once selected, the preferred title display becomes
the display default. When a function adjustment
such as volume is made, the screen will momentarily switch to that function’s display, then revert
back to the preferred title display several seconds
after the adjustment.
∗ If the key operation is performed with the screen
saver function on, the operation display corresponding to the key operation is shown for about
30 seconds and the display returns to the screen
saver display. For details, refer to the subsection
“Turning the screen saver function on or off” in
section “Common Operations”.
Switching the display layout
] key for more than 1 second to
1. Touch the [
switch display layout.
] key for more
2. Each time you touch the [
than 1 second, the display layout switches in
the following order:
Title mode
Indicator mode
Example: iPod
Clock
Sound adjustments
You can adjust a sound effect or tone quality to
your preference.
To change sound setting
1 . Touch the [ ] key to switch to ADJ menu.
2 . Select “SOUND” in the menu to enter
Sound Adjustment mode.
] slider or touch [ ] /
3 . Slide along the [
[ ] key, the Sound Adjustment mode
changed as following order:
(“BASS”
“BEAT EQ”
“MID”
“TREBLE”)∗1
“BBE MP”∗2
“BALANCE”
“FADER”
“M-BEX”
“HPF”
“S-W LPF”
“S-W VOL”
“BEAT EQ”...
Notes:
∗1 : BASS/MID/TREBLE are only available if
“CUSTOM” is selected in “BEAT EQ”.
∗2 : BBE MP is only available if “USB” is
selected in source mode and the “OUTPUT
FORM” is set to “DIGITAL”. (Please refer to
page 30)
Setting the BEAT EQ
This unit is provided with 4 types of sound tone
effects stored in memory. Select the one you prefer.
∗ The factory default setting is “OFF”.
Select “BEAT EQ”.
Touch [ ] key to enter detail setting stage.
3 - 3 . During detail setting stage, each time your
] slider or touch [ ] / [ ]
slide along [
key, the tone effect changes in the following
order:
“OFF”
“BASS BOOST”
“IMPACT”
“EXCITE”
“CUSTOM”
OFF
: No sound effect
BASS BOOST : Bass emphasized
IMPACT
: Bass and treble emphasized
EXCITE
: Bass and treble emphasized
mid emphasized
CUSTOM
: User custom
3-1.
3-2.
∗ When CT data is not received, “
” appears in the display for Title mode and Indicator
mode, while “
” appears in the display for
Clock mode.
12
FZ709E
English
Basic Operations
When “BASS BOOST”/“IMPACT”/
“EXCITE” is set:
“BASS BOOST”/“IMPACT”/“EXCITE” will appear
after the “BEAT EQ” item in the sound Adjustment mode.
3 - 3 - 1 . Select the item and touch [
] key to enter
detail setting stage.
3 - 3 - 2 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the setting in the range of -3
to +3.
∗ The factory default setting is “0”.
3-3-3.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
When “CUSTOM” is set:
3-3-1.
] slider or touch [ ]/[ ]
Slide along [
key to select the “BASS”, “MID” or “TREBLE” mode to adjust.
Adjusting the bass
This adjustment can be performed only when the
BEAT EQ is set to “CUSTOM”.
3 - 1 . Select “BASS”.
3 - 2 . Touch [ ] key to enter detail setting stage.
Touch [ ] / [ ] key to select Gain(“G”),
center frequency(“F”) or Q factor(“Q”).
3 - 4 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the value.
3-3.
∗ The factory default setting:
G : “0” (Adjustment range: +7 to -7)
F : “50Hz” (Adjustment range: 50/100/200)
Q : “1.0” (Adjustment range: 0.7/1.0/1.4/2.0)
3-5.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Adjusting the mid
This adjustment can be performed only when the
BEAT EQ is set to “CUSTOM”.
3 - 1 . Select “MID”.
3 - 2 . Touch [ ] key to enter detail setting stage.
]/[
] key to select Gain(“G”),
Touch [
center frequency(“F”) or Q factor(“Q”).
3 - 4 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the value.
3-3.
∗ The factory default setting:
G : “0” (Adjustment range: +7 to -7)
F : “500Hz” (Adjustment range: 500/1k/2k)
Q : “1.0” (Adjustment range: 0.7/1.0/1.4/2.0)
FZ709E
13
English
Basic Operations
3-5.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Adjusting the treble
This adjustment can be performed only when the
BEAT EQ is set to “CUSTOM”.
3 - 1 . Select “TREBLE”.
3 - 2 . Touch [ ] key to enter detail setting stage.
]/[
] key to select Gain(“G”),
Touch [
center frequency(“F”) or Q factor(“Q”).
3 - 4 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the value.
3-3.
∗ The factory default setting:
G : “0” (Adjustment range: +7 to -7)
F : “10kHz” (Adjustment range: 5k/10k/15k)
Q : “1.0” (Adjustment range: 0.7/1.0/1.4/2.0)
14
FZ709E
3-5.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Setting the BBE MP (Sound
Enhancement and Restoration for
compressed audio files)
BBE MP (Minimized Polynomial Non-Linear Saturation) Process improves digitally compressed
sound, such as MP3, by restoring and enhancing
the harmonics lost through compression. BBE
MP works by regenerating harmonics from the
source material, effectively recovering warmth,
detail and nuance.
∗ This function is effective for the audio files in the
USB/iPod mode, but it is ineffective for the video
in the USB/iPod mode.
Select “BBE MP”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select the value in sequence of
“OFF”
“ON”
3-1.
3-2.
∗ The factory default setting is “OFF”.
When “ON” is set:
3-3-1.
3-3-2.
Touch [ ] key to enter detail setting
stage.
] slider or touch [ ]/[ ]
Slide along [
key to select the value in sequence of
“HIGH”
“MID”
“LOW”
∗ The factory default setting is “MID”.
3-4.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Adjusting the balance
Select “BALANCE”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the balance of the right and left
speakers.
3-1.
3-2.
∗ The factory default setting is “CENTER”.
(Adjustment range: RIGHT 12 to LEFT 12)
3-4.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Adjusting the fader
Select “FADER”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the balance of the rear and front
speakers.
3-1.
3-2.
∗ The factory default setting is “CENTER”.
(Adjustment range: FRONT 12 to REAR 12)
3-4.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Adjusting the M-BEX
Select “M-BEX”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to turn on or turn off the MAGNA BASS
EXTEND effect.
3-1.
3-2.
∗ The factory default setting is “OFF”.
(Adjustment range: ON/OFF)
3-4.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Adjusting the high pass filter
Select “HPF”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select the setting in sequence
“60”
“90”
“120”
“THROUGH”
3-1.
3-2.
English
Basic Operations
∗ The factory default setting is “THROUGH”.
∗ This is supported only with amplifiers
equipped with this function. Output is not
supported from RCA cables.
Setting the subwoofer
You can set the low pass filter of subwoofer.
3 - 1 . Select “S-W LPF”.
3 - 2 . Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select the setting in sequence
“THROUGH”
“60”
“90”
“120”
∗ The factory default setting is “THROUGH”.
Adjusting the subwoofer output
volume
You can adjust the volume output from the unit’s
subwoofer output terminal.
This adjustment can be performed only when the
“S-W LPF” is set to “60”, “90” or “120”.
3 - 1 . Select “S-W VOL”.
3 - 2 . Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to increases or decreases the subwoofer
volume.
∗ The factory default setting is “0”.
(Adjustment range: +6 to -6)
∗ When the volume level is more than 30, the
subwoofer volume adjustment value can not
reach +6.
Note:
During SOUND adjustment mode, if no operation
is performed for more than 10 seconds, this mode
can be cancelled and return to previous mode.
FZ709E
15
English
Basic Operations
CT(Clock Time) function
The CT function receives CT data sent from
an Radio Data System station and displays the
time.
∗ If a CT data is not being received, “
” appears in the display.
Note:
CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT may not display accurately.
Radio Mode Operations
Listening to the radio
] key to switch to Source menu.
1. Touch the [
2. Select “TUNER” to enter Radio mode. The
frequency or PS and PTY appears in the display.
PS: Programme service name
PTY: Programme type
3. To select a preset band, touch the [ ] key and
then select one of the preset bands such as
FM1, FM2, FM3 or AM1.
Every time the [ ] key is touched, the band
switches in the following order:
FM1 FM2 FM3 AM1 FM1...
4. Touch the [ ]/[ ] key to tune in the desired
station.
Tuning
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
Seek tuning
There are 2 types of seek tuning: DX SEEK and
LOCAL SEEK.
DX SEEK can automatically tune in to receivable
broadcast stations; LOCAL SEEK can tune in to
only broadcast stations with a good reception
sensitivity.
1. Touch the [ ] key and select the desired band
(FM or AM).
∗ If
is lit in the display, touch and hold the
[ ] key for 1 second or longer.
in the
display goes off and seek tuning is now available.
∗ If
is lit in the display, TP stations are automatically sought.
2. Touch the [ ]/[ ] key to start automatic station tuning.
When the [ ] key is touched, the station is
sought in the direction of higher frequencies;
if the [ ] key is touched, the station is sought
in the direction of lower frequencies.
16
FZ709E
DX SEEK
When the [ ] key is touched, search will be performing in the direction of higher frequencies.
When the [ ] key is touched, search will be performed in the direction of lower frequencies.
∗ When seek tuning starts, “DX SEEK” appears in
the display.
LOCAL SEEK
If the key is touched and held in position for 1
second or longer, local seek tuning will be enabled. Broadcast stations with good reception
sensitivity are selected.
∗ When local seeking starts, “LO SEEK” appears in
the display.
Manual tuning
There are 2 ways available:
Quick tuning and step tuning.
When you are in the step Tuning mode, the frequency changes one step at a time. In the Quick
Tuning mode, you can quickly tune the desired
frequency.
1. Touch the [ ] key and select the desired band
(FM or AM).
∗ If
is not lit in the display, touch and hold
is lit
the [ ] key for 1 second or longer.
in the display and manual tuning is now available.
2. Tune into a station.
Quick tuning
Touch and hold the [ ] / [ ] key for 1 second or
longer to begin station tuning.
Step tuning
Touch the [
ing.
]/[
] key to perform manual tun-
English
Radio Mode Operations
TUNER OPTION
] key to
1 . During Tuner mode, touch the [
switch to ADJ menu.
2 . Select “OPTION” in the menu to enter
Tuner Option mode.
] slider or touch [ ]/[ ]
3 . Slide along [
key, the TUNER OPTION mode changed
as following order:
(“PTY”
“P.CH MEMORY”
“PTY SELECT”
“AF”
“REG”)
“LANGUAGE”
“PRESET SCAN”
“AUTO STORE”
“P.CH MEMORY”...
Notes:
Items in bracket (PTY, PTY SELECT, AF, REG)
are called Radio Data System Adjustment
mode. Please refer to page 20 for Radio Data
System Adjustment mode.
“PTY SELECT” only available when “PTY” is
on.
“REG” only available when “AF” is on.
Preset memory function
Preset memory function can store up to 24 stations: Six stations for each of FM1, FM2, FM3,
and AM1.
Manual memory function
Select “P.CH MEMORY”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select the preset channel number to
be stored.
3 - 4 . Touch [ENT] key for 2 seconds to store the
frequency into the selected preset channel.
3 - 5 . “MEMORY” is displayed for 2 seconds before
revert to main display.
3-1.
3-2.
∗ If no operation is performed for more than 7 seconds, manual tuning is cancelled and the display
returns to the previous mode.
Radio function
You need to enter the TUNER OPTION to perform the Radio function.
FZ709E
17
English
Radio Mode Operations
Preset scan
Preset scan receives the stations stored in preset memory in order. This function is useful when
searching for a desired station in memory.
3 - 1 . Select “PRESET SCAN”.
3 - 2 . Touch [ENT] key to start scan preset channel.
3 - 3 . When a desired station is tuned in, touch
the [ ] / [ ] key to continue receiving that
station.
Auto store
Auto store is a function for storing up to 6 stations
that are automatically tuned in sequentially. If 6
receivable stations cannot be received, a previously stored station remains un-overwritten at
the memory position.
3 - 1 . Select “AUTO STORE”.
3 - 2 . Touch [ENT] key to start performing auto
store function.
3 - 3 . The stations with good reception are stored
automatically to the preset channels.
∗ If auto store is performed in the FM bands,
the stations are stored in FM3 even if FM1 or
FM2 was chosen for storing stations.
∗ “AUTO STORE” will appears in the display.
Recalling a preset station
A total of 24 preset positions (6-FM1, 6-FM2, 6FM3, 6-AM1) exists to store individual radio stations in memory.
1. Touch the [ ] key to select the desired band.
] slider or touch [ ]/[ ] key
2. Slide along [
to select the desired preset station.
3. Touch [ENT] key to recall the stored radio
frequency.
18
FZ709E
Radio Data System
This unit has a built-in Radio Data System decoder system that supports broadcast stations
transmitting Radio Data System data.
This system can display the name of the broadcast station being received (PS) and can automatically switch to the broadcast station with the
best reception as you move long distances (AF
switching).
Also, if a traffic announcement or programme
type is broadcast from an Radio Data System
station, no matter what mode you are in, this
broadcast is received. Additionally, if EON information is received, this information enables
automatic switching of other preset stations on
the same network and interruption of the station
being received with traffic information from other
stations (TP). This function is not available in
some areas. When using the Radio Data System
function, always set the radio to FM mode.
AF : Alternative Frequency
PS : Programme Service Name
PTY : Programme Type
EON : Enhanced Other Network
TP : Traffic Programme
∗ Radio Data System interrupt does not function
during AM radio reception.
∗ When set receives Radio Data System signal, and
can read PS data, PS appears in the display.
TA (Traffic Announcement)
In the TA standby mode, when a traffic announcement broadcast starts, the traffic announcement
broadcast is received as top priority regardless of
the Function mode so you can listen to it. Traffic
programme (TP) automatic tuning is also possible.
Setting the TA standby mode
If you touch the [ ] key when only
is lit in
the display,
and
light in the display and
the unit is set into the TA standby mode until a
traffic announcement is broadcast. When a traffic announcement broadcast starts, “TRA INFO”
] key
appears in the display. If you touch the [
while a traffic announcement broadcast is being
received, the traffic announcement broadcast reception is cancelled and the unit goes into the TA
standby mode.
English
Radio Data System Operations
Cancelling the TA standby mode
As
and
lit in the display, touch the [ ]
key. The
in the display goes off and the TA
standby mode is cancelled.
∗ If
is not lit, touch the [
TP station.
] key searches for a
Searching for a TP station
When
is not lit, if you touch the [ ] key,
in the display lights and the unit automatically receives a TP station.
Note:
If a TP station is not received, the unit continues the
] key again goes off
search operation. Touch [
in the display and stops TP station searching.
Emergency broadcast
If an emergency broadcast is received, all the
Function mode operations are stopped. “ALARM”
appears in the display and the emergency broadcast can be heard.
Cancelling an emergency broadcast
] key, emergency broadcast
If you touch the [
reception is cancelled.
∗ This function can only be used when
is lit in the
display. When
is lit, this means that the Radio
Data System broadcast station being received has
traffic announcement programmes.
FZ709E
19
English
Radio Data System Operations
Volume setting of TA, emergency
broadcast (ALARM) and PTY
The volume for TA, ALARM and PTY interrupts
can be set during TA, ALARM or PTY interrupt.
∗ The factory default setting for this volume is “VOL
15”.
During a TA, ALARM or PTY interrupt, slide the
[
] slider to set the volume to the desired level
(0 to 33).
∗ When the TA, ALARM or PTY interrupt ends, the
volume returns to the level it had before the interrupt.
Radio Data System Adjustment
mode
PTY
This function enables you to listen to a broadcast
of the selected programme type even if the unit is
on a Function mode other than radio.
∗ Some countries do not yet have PTY broadcast.
∗ In the TA standby mode, a TP station has priority
over a PTY broadcast station.
∗ The factory default setting is “OFF”.
Select “PTY”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3 - 4 . After completing settings, touch the [ENT]
key to return to the 1st selected item.
3-1.
3-2.
ON
“PTY” in the display lights and PTY standby
mode is turned on. When the selected
PTY broadcast starts, the PTY item name
appears in the display.
Radio Data System function
You need to enter the TUNER OPTION to perform the Radio Data System function.
OFF
“PTY” in the display goes off and PTY
standby mode is cancelled.
TUNER OPTION
] key to
1 . During Tuner mode, touch the [
switch to ADJ menu.
2 . Select “OPTION” in the menu to enter
TUNER OPTION mode.
] slider or touch [ ]/[ ]
3 . Slide along [
key, the TUNER OPTION mode changed
as following order:
(“PTY”
“P.CH MEMORY”
“PTY SELECT”
“AF”
“REG”)
“LANGUAGE”
“PRESET SCAN”
“AUTO STORE”
“P.CH MEMORY”...
Notes:
Item in bracket (PTY, PTY SELECT, AF, REG)
are called Radio Data System Adjustment
mode.
“PTY SELECT” only available when “PTY” is
on.
“REG” only available when “AF” is on.
20
FZ709E
Cancelling a PTY interrupt broadcast
] key during the PTY interrupt
Touch the [
broadcast, the PTY interrupt is cancelled
and the unit returns to PTY standby mode.
Selecting PTY
Select “PTY SELECT”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select the desired PTY.
3-1.
3-2.
PTY seek
Touch the [ ] key to search for a
PTY broadcast in the direction of
]
higher frequencies; touch the [
key to search in the direction of lower
frequencies.
3 - 5 . “PTY SEEK” is displayed.
There are 29 types of PTY below can be selected.
ENGLISH
News
Affairs
Info
Sport
Educate
Drama
Culture
Science
Varied
Pop M
Rock M
Easy M
Light M
Classics
Other M
Weather
Finance
Children
Social
Religion
Phone In
Travel
Leisure
Jazz
Country
Nation M
Oldies
Folk M
Document
3-4.
PTY item
CONTENTS
News
Today’s events
Information
Sports
Education
Drama
Culture
Science
Variety
Pop music
Rock music
Easy music
Light music
Classics
Other music
Weather
Finance
For children
Social
Religion
Phone in
Travel
Leisure
Jazz
Country
Nation music
Oldies
Folk music
Documentaries
∗ During PTY list, if no operation is performed for 7
seconds, the display will return to 1st “PTY SELECT”
item.
English
Radio Data System Operations
∗ If no station with the selected PTY
broadcast can be received, the unit
returns to the previous selected PTY in
the PTY list.
∗ If station is found, PTY name and PS
name will be displayed for 7 seconds
before back to PTY list.
AF function
The AF function switches to a different frequency
on the same network in order to maintain optimum reception.
∗ The factory default setting is “ON”.
Select “AF”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3 - 4 . After completing settings, touch the [ENT]
key to return to the 1st selected item.
3-1.
3-2.
ON
“AF” in the display lights and AF function
turns on.
OFF
“AF” in the display goes off and AF
function turns off.
∗ If the reception of the current broadcast station deteriorates, “SEARCH” appears in the
display and the radio searches for the same
programme on another frequency.
REG (Regional programme) function
When the REG function is ON, the optimum regional station can be received. When this function is OFF, if the regional station area switches
as you drive, a regional station for that region is
received.
∗ The factory default setting is “OFF”.
FZ709E
21
English
Radio Data System Operations
Notes:
This function is disabled when a national station
such as BBC R2 is being received.
The REG function ON/OFF setting is valid when
the AF function is ON.
Select “REG”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3 - 4 . After completing settings, touch the [ENT]
key to return to the 1st selected item.
3-1.
3-2.
ON
“REG” in the display lights and REG function
turns on.
OFF
“REG” in the display goes off and REG
function turns off.
Manually tuning a regional station in
the same network
1. This function is valid when the AF function is ON and the REG function is OFF.
Note:
This function can be used when a regional
broadcast of the same network is received.
] slider or touch [ ]/[ ]
2. Slide along [
key to call out the regional station.
3. If the reception condition of the called out
] slider or
station is bad, slide along [
]/[
] key to select the same
touch [
number. The unit receives a local station
on the same network.
Switching the PTY display language
You can select one of 4 languages (English,
Deutsch, Svenska, Francais) for the PTY displayed in the display.
∗ The factory default setting is “English”.
Select “LANGUAGE”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select desired language.
3 - 4 . After completing settings, touch the [ENT]
key to return to the 1st selected item.
3-1.
3-2.
22
FZ709E
Auto store function for TP stations
You can automatically store up to 6 TP stations
into preset memory. If the number of TP can be
received less than 6, broadcast stations already
stored in memory and left without being overwritten.
3 - 1 . As
lit in the display, select “AUTO
STORE”.
3 - 2 . Touch [ENT] key to start performing auto
store function.
3 - 3 . The stations with good reception are stored
automatically to the preset channels.
∗ Even if you select FM1 or FM2, a TP station
is stored into memory for FM3.
USB memory device operation
About USB memory
USB is an acronym for Universal Serial Bus, and
refers to an external bus standard supporting
data transfer rates of 12 Mbps.
This unit is compatible with USB 1.1/2.0 with
maximum data transfer rates of 12 Mbps.
USB memory devices that can be played by
connecting to the unit’s USB cable are limited
to those recognized as “USB mass storage
class devices”; operation is not guaranteed
with all USB memory devices.
∗ Devices compatible with “USB Mass Storage
Class” can be used merely by connecting to the
host device, without need for special drivers or
application software.
Consult the manufacturer of your USB memory
device for information regarding whether it
is supported by “USB Mass Storage Class”
standards.
Audio files playable on this unit are limited to
MP3/WMA/AAC files.
To prevent the accidental loss of data, always
back up important data on your computer.
This unit does not support connections to a computer. In addition, connections made through a
USB hub device are also not supported.
When a USB memory device is composed of
two or more drives, only one of the drives will
be detected.
USB memory devices with security functions
cannot be played.
The order in which tracks are recorded may differ depending on the USB memory device connected (the actual playback order may not be
the same as that indicated on your computer’s
display).
If you continuously operate folder up/down, the
play time keeps as “00:00”, and the sound is
not emitted.
What is MP3?
MP3 is an audio compression method and classified into audio layer 3 of MPEG standards. This
audio compression method has penetrated into
PC users and become a standard format. This
MP3 features the original audio data compression to about 10 percent of its initial size with a
high sound quality. This means that several music CDs can be recorded on a USB memory device to allow a long listening time∗.
English
USB Operations
∗ Depends on the USB memory device storage
capacity.
What is WMA?
WMA is the abbreviation of Windows Media Audio, an audio file format developed by Microsoft
Corporation.
Notes:
If you play a file with DRM (Digital Rights Management) for WMA remaining ON, no audio is output
(The “--:--” and
indicator blinks for 5 seconds
and go to next track).
TM
Windows Media , and the Windows® logo are
trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other
countries.
To disable DRM
(Digital Rights Management)
1. When using Windows Media Player 9/10/11,
click on TOOL
OPTIONS
MUSIC RECORD tab, then under Recording settings, unclick the check box for RECORD PROTECTED
MUSIC. Then, reconstruct files.
Personally constructed WMA files are used at
your own responsibility.
FZ709E
23
English
USB Operations
What is AAC?
AAC is an acronym for “Advanced Audio
Coding” and refers to the audio compression
method used with video compression standards
MPEG-2 and MPEG-4.
AAC files composed with the following conditions can be played:
AAC files encoded with iTunes.
iTunes Ver. 7.0 or earlier.
File extension “.m4a” (“.M4A”)
Tracks purchased at an iTunes Store, and
copyright-protected files cannot be played.
When playing AAC files that include image data,
additional time may be required before playback
begins.
Files may not play properly, depending on the
iTunes version under which an AAC file is encoded.
Precautions when creating MP3/
WMA/AAC file
Usable sampling rates and bit rates
See “USB” (page 43) for details.
File extensions
1. Always add a file extension “.MP3”, “.WMA”
or “.M4A” to MP3, WMA or AAC file by using
single byte letters. If you add a file extension
other than specified or forget to add the file
extension, the file cannot be played.
2. Files without MP3/WMA/AAC data will not play.
The indication “NO FILE” appears in the play
time display if you attempt to play files without
MP3/WMA/AAC data.
∗ When VBR files are played, the play time display
may differ the play location.
∗ When MP3/WMA/AAC files are played, a little
no sound part is caused between tunes.
24
FZ709E
Logical format (File system)
1. When writing MP3/WMA/AAC file, please
select “FAT12”, “FAT16” or “FAT32” as the
file system format. Normal play may not be
possible if the files are recorded on another
format.
2. The folder name and file name can be displayed as the title during MP3/WMA/AAC
play but the title must be within 64 single byte
alphabetical letters and numerals (including an
extension).
3. Do not affix a name to a file inside a folder
having the same name.
Note:
File names in small letters with less than 8 characters (not including file extension) will be displayed
in capital letters.
Folder structure
1. A USB with a folder having more than 8 hierarchical levels will be impossible.
Number of files or folders
1. Up to 255 files per folder can be recognized.
Up to 512 folders can be recognized and up
to total of 130560 files can played.
2. Tracks are played in the order that they were
recorded onto a USB. (Tracks might not always
be played in the order displayed on the PC.)
3. Some noise may occur depending on the type
of encoder software used while recording.
! CAUTION
Insert and remove a USB memory device
only when the device is not being accessed.
Connecting or disconnecting the device at
the following times may result in the loss of
data:
- If the USB memory device is removed or
power is disconnected during writing to
the device.
- When the device is subjected to static
electricity or electric noise.
Do not leave a USB memory device unattended in an automobile. Exposure to direct
sunlight or high temperatures may cause
deformation or other malfunction of the USB
memory device.
Connecting a USB memory device
1. Connect the USB memory device to the USB
slot.
Playback will begin from the first file recorded
on the device.
]
∗ If the device is not recognized, touch the [
key to switch to the Source menu and select
the source to the device.
∗ Always insert the device fully into the connector.
Incomplete connections may cause the device
not to be recognized.
∗ Depending on the number of tracks recorded,
some amount of time may be required until all
tracks are read into the unit.
∗ The order in which tracks are recorded may
differ depending on the device connected (the
actual playback order may not be the same as
that indicated on your computer’s display).
To listen to tracks on a connected
USB memory device
] key to switch to the Source
1. Touch the [
menu and select the “USB”. When USB
memory device is selected, playback (except
DRM files) will begin from the location at which
playback was previously stopped.
∗ When a USB memory device is connected the
USB mode will be displayed.
∗ When a USB memory device is disconnected
and then reconnected, playback will begin
from the previous position where playback is
stopped.
∗ When a USB memory device is disconnected
and then a different USB memory device is
connected, playback will begin from the first file
recorded on the device.
To stop play
] key and switch the function to
1. Touch the [
a source other than the USB memory device.
! CAUTION
Do not remove the USB memory device when
the USB mode is selected, since it may result
in loss or damage to data on the USB memory
device.
Always backup and save important data on
your computer.
English
USB Operations
2. Remove the USB memory device from the USB
slot.
Pausing play
] key to pause play. “PAUSE”
1. Touch the [
appears in the display.
] key again.
2. To resume play, touch the [
Selecting a track
Track-up
1. Touch the [ ] key to move to the beginning
of the next track.
2. Each time the [ ] key is touched, playback
proceeds to another track in the advancing
direction.
Track-down
1. Touch the [ ] key to move to the beginning
of the current track.
2. Touch the [ ] key twice to move to the beginning of the previous track.
Fast-forward/fast-backward
Fast-forward
Touch and hold the [
ger.
] key for 1 second or lon-
Fast-backward
Touch and hold the [
ger.
] key for 1 second or lon-
Top function
Touch the [ ] key for 1 second or longer, then
the USB memory device will start playing the first
track of current folder.
FZ709E
25
English
USB Operations
Other various play functions
USB OPTION
] key to
1 . During USB mode, touch the [
switch to ADJ menu.
2 . Select “OPTION” in the menu to enter USB
Option mode.
] slider or touch [ ]/[ ]
3 . Slide along [
key, the USB Option mode changed as
following order:
“SCAN”
“REPEAT”
“RANDOM”
“SCAN”
Note:
During trick play, “TRICK OFF” will be appeared
before “SCAN” item.
Scan play
This function allows you to locate and play the
first 10 seconds of all the tracks in current folder.
3 - 1 . Select “SCAN”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “TRACK”.
3 - 4 . Touch the [ENT] key, “TRACK SCAN” will be
displayed for 2 seconds.
3 - 5 . During scan,
will keep blinking.
∗ Scan play starts from the next track after the
track currently being played.
∗ Scan play will proceed to next folder after
all the tracks in the current folder have been
scanned.
All scan play
This function allows you to locate and play the
first 10 seconds of the first track of all the folders.
3 - 1 . Select “SCAN”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ALL”.
3 - 4 . Touch the [ENT] key, “ALL SCAN” will be
displayed for 2 seconds.
3 - 5 . During scan,
will keep blinking.
∗ All scan play starts from the first track of next
folder.
26
FZ709E
Repeat play
This function allows you to play the current track
repeatedly.
3 - 1 . Select “REPEAT”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “TRACK”.
3 - 4 . Touch the [ENT] key, “TRACK REPEAT” will
be displayed for 2 seconds.
3-5.
lights in the display.
All repeat play
This function allows you to play all tracks in the
MP3/WMA/AAC current folder repeatedly.
3 - 1 . Select “REPEAT”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ALL”.
3 - 4 . Touch the [ENT] key, “ALL REPEAT” will be
displayed for 2 seconds.
3-5.
lights in the display.
Random play
This function allows you to play all tracks of current folder in a random order.
3 - 1 . Select “RANDOM”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “TRACK”.
3 - 4 . Touch the [ENT] key, “TRACK RANDOM”
will be displayed for 2 seconds.
3-5.
lights in the display.
All random play
This function allows you to play all the tracks of
all the folders recorded on an USB in a random
order.
3 - 1 . Select “RANDOM”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ALL”.
3 - 4 . Touch the [ENT] key, “ALL RANDOM” will be
displayed for 2 seconds.
3-5.
lights in the display.
To cancel trick play
Select “TRICK OFF”.
3 - 2 . Touch [ENT] key to cancel trick play.
3 - 3 . Display will return to playback display.
3-1.
Folder Select
This function allows you to select a folder containing MP3/WMA/AAC files and start playing
from the first track in the folder.
] slider or touch [ ]/[ ]
1. Slide along [
key.
Touch [ ] key to move the next folder. Touch
[ ] key to move the previous folder.
∗ Touch [ ] key while in the final folder will shift
to the first folder.
∗ Folder without a MP3/WMA/AAC file is not
selectable.
iPod Operations
This section describes operations when connected to an Apple iPod via the USB slot.
Notes:
See the iPod Owner’s Manual for details regarding
operation conditions.
The unit will not operate, or may operate improperly
with unsupported versions.
For a list of compatible Apple iPod unit with the this
model, please contact your Clarion dealer or www.
clarion.com.
English
USB Operations
Connecting an iPod
When an iPod is connected to the USB slot,
“Shuffle” set on the iPod will become as follows:
“Shuffle (Albums)” play
Random play
“Shuffle (Songs)” play
All random play
The iPod have iPod menu which can toggle with
Play mode by touching the [ ] key for 1 second
or longer.
If iPod supports video capability, the following
screen will be displayed first before switching to
the iPod menu.
Touch [ENT] key to enter music menu or video
menu.
Select iPod mode
1. Connect your iPod to the USB connector. The
system will automatically detect the connected
device and change to the USB mode (iPod
mode) and start playback after a while.
When an iPod is already connected
1. Touch the [
] key to switch to the source
menu.
2. Touch the "USB" to select the iPod mode.
The system changes to the USB mode (iPod
mode), and starts playback from the previous
position.
FZ709E
27
English
iPod Operations
Note:
The following operations in Play mode operate the
same as in USB mode:
∗ Track selection: [ ] , [ ]
∗ Fast-forward/fast-backward: [ ] , [ ]
]
∗ Pause: [
See “USB Operations” (page 23) for details.
Other various play functions
(in Play mode)
Notes:
These functions are not supported when in the iPod
menu.
The Random function set on the iPod remains the
same after attachment/detachment of the iPod.
The Repeat function on the iPod will be changed
when you connect/disconnect the iPod to the
unit.
iPod OPTION
] key to
1 . During USB mode, touch the [
switch to ADJ menu.
2 . Select “OPTION” in the menu to enter iPod
Option mode.
] slider or touch [ ]/[ ]
3 . Slide along [
key, the iPod Option mode changed as
following order:
“REPEAT”
“RANDOM”
“OUTPUT FORM”
“SIMPLE MODE”
“REPEAT”...
Note:
During trick play, “TRICK OFF” will be appeared
before “REPEAT” item.
Repeat play
Play back one track repeatedly.
3 - 1 . Select “REPEAT”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON”.
3 - 4 . Touch the [ENT] key, “REPEAT ON” will be
displayed for 2 seconds.
3-5.
light in the display.
28
FZ709E
Repeat off
This function allows you to play all tracks in the
current folder repeatedly.
3 - 1 . Select “REPEAT”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “OFF”.
3 - 4 . Touch the [ENT] key, “REPEAT OFF” will be
displayed for 2 seconds.
Random play
Play all albums within a selected category, in random order. (Corresponds to “Shuffle (Albums)”
command on iPod.)
Select “RANDOM”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “TRACK”.
3 - 4 . Touch the [ENT] key, “TRACK RANDOM”
will be displayed for 2 seconds.
3-5.
light in the display.
3-1.
3-2.
All random play
Play all tracks within a selected category, in random order. (Corresponds to “Shuffle (Songs)”
command on iPod.)
Select “RANDOM”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ALL”.
3 - 4 . Touch the [ ENT ] key, “ALL RANDOM”
will be displayed for 2 seconds.
3-5.
light in the display.
3-1.
3-2.
To cancel trick play
Select “TRICK OFF”.
Touch the [ENT] key to cancel trick play.
3 - 3 . Display will return to playback display.
3-1.
3-2.
Note:
When playing the last track within a selected
category in Random mode, if ACC is switched off
then on again, playback will begin from a different
track.
Selecting category from the iPod
music menu
1. Touch and hold the [ ] key for 1 second or
longer.
2. Select to switch to music menu or video
menu.
3. If “MUSIC” is selected from the list, iPod music
menu categories will be displayed.
Notes:
If the iPod does not support video, the iPod music
menu categories will be displayed directly.
Repeat and Random mode operations are not
supported when in the iPod menu.
In iPod menu, if you touch the [ ] / [ ] or touch
[ ]/[ ] key fast, playback may not be performed.
] slider or touch [ ]/[ ] key
4. Slide along [
to select the category.
5. There are 6 categories in the iPod music
menu:
Playlists
Artists
Albums
Songs
Genres
Composers
6. Touch [ ]/[ ] key to switch between layer.
7. When the track name display is showing, touch
the [ENT] key.
Playback will begin from the selected track in
the selected category, and the iPod menu will
be canceled.
∗ Subfolders may be displayed, depending on the
category.
In this case, use the [ ] / [ ] key to switch
between subfolders, then use the [ ] key to
select the desired subfolder.
∗ When the track name display is showing, touch
the [ ] key will return to the currently playing
folder name display.
] slider or touch [
8. Slide along [
to select a track within a category.
]/[
] key
Selecting category from the iPod
video menu
1. Touch and hold the [ ] key for 1 second or
longer.
2. Select to switch to music menu or video
menu.
3. If “VIDEO” is selected from the list, iPod video
menu categories will be displayed.
English
iPod Operations
Note:
Repeat and Random mode operations are not
supported when in the iPod menu.
] slider or touch [ ]/[ ] key
4. Slide along [
to select the category.
5. The categories in the iPod video menu is depend on the iPod.
∗ During video files playback, if ACC is switched
off then switched on again, or if iPod is disconnected, playback cannot be resumed.
∗ Random play cannot be selected in iPod video
mode. There is no album in the video menu.
∗ Please set the language setting in the iPod to
English as this unit can only display English.
iPod menu ABC search
This function searches the subfolders for desired
alphabetical letters.
] slider
1. During iPod menu, slide along [
or touch [ ]/[ ] key and select the desired
category.
2. Touch [ ] key.
∗ Subfolders maybe displayed, depending on
] slider
the categary. You can slide along [
or touch [ ]/[ ] key to switch between the
] key to enter the
subfolders and use the [
next subfolder layer.
3. Touch the [
] key for 1 second or longer.
∗ A small window for alphabet selection will be
displayed.
] slider
4. Select the alphabet by slide along [
or touch [ ]/[ ] key and touch [ENT] key to
perform search.
5. “SEARCHING” will be displayed.
FZ709E
29
English
iPod Operations
About title display
This unit supports the display of title information
transmitted from a connected iPod.
Character code information is UTF-8; displayable characters include English alphanumerics,
some symbols, and some umlaut characters.
Unsupported characters will be replaced by
asterisks (∗).
Output form
This function is to select digital output or analog output from this unit. This setting is for video
playback via iPod 5G.
When you connect other than iPod 5G or when
you play only audio files, please set this setting
to “DIGITAL”.
If you set this setting to “ANALOG”, optional iPod
video cable CCA723 is required.
∗ The factory default setting is “DIGITAL”.
Select “OUTPUT FORM”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ] / [ ]
key to select “DIGITAL” or “ANALOG”.
3 - 4 . After completing settings, touch the [ENT]
key to return to the 1st selected item.
3-1.
3-2.
Note:
The setting will only take effect after disconnecting
and re-connecting the iPod.
Select Simple Control mode
This function is to select the mode to operate the
iPod contents.
∗ The factory default setting is “OFF”.
Select “SIMPLE MODE”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3-1.
3-2.
30
FZ709E
ON
To operate iPod contents from iPod.
OFF
To operate iPod contents from this unit.
3-4.
After completing settings, touch the [ENT]
key to return to the 1st selected item.
Notes:
During iPod Simple mode ON, “iPod Mode” will
be displayed as below and cannot switch to other
display layout:
During Simple Mode On, do not operate from iPod
and this unit at the same time.
iPod 5G and iPod nano 1G cannot select both
digital output and simple control mode on at the
same time.
∗ Output form: Digital and Simple mode:
OFF - Default
∗ Output form: Digital and Simple mode:
ON - Not selectable
∗ Output form: Analog and Simple mode:
ON/OFF - Requires CCA723 cable
During Simple Mode On, please do not change the
repeat setting to “OFF” in the iPod.
The Bluetooth® interface allows you to utilize
your car’s built-in audio system for wireless mobile phone or music handsfree communication.
This unit will be able to retrieve phonebook contacts, perform outgoing call, receive incoming
call and listen to music.
Note:
When an audio device is paired, the following
operations are the same as USB mode:
∗ Play/Pause
∗ Track up/down
See “USB Operations” (page23) for details.
Basic Operations
1. Touch the [ADJ] key to switch to ADJ menu.
2. Select “TEL” in the menu, display will be shown
as below:
3. Touch the [ ] key to select “CALL” to enter
TEL MENU.
4. Touch the [ ] key to select “OPT” to enter TEL
OPTION mode.
Note:
“CALL” will only appear if paired mobile phone is
connected.
TEL MENU (Call method)
] slider or touch [ ]/[ ]
1 . Slide along [
key, the call method changed as following
order:
“PHONE BOOK”
“HISTORY”
“REDIAL”
“DIAL NUMBER”
“PHONE BOOK”...
Call from Phonebook
Select “PHONE BOOK”.
] key to enter the contact name
Touch the [
] slider
mode (In this case, slide along [
or touch [ ]/[ ] key to select the desired
contact name).
1 - 3 . When the contact name is displayed, touch
the [ ] key to view details.
1 - 4 . When contact name or contact details is
displayed, touch the [ENT] key to call the
mobile phone number.
1-1.
1-2.
English
Bluetooth® Operations
Received/Dialled/Missed Call History
You can browse and call from Received/Dialled/
Missed Call History.
1 - 1 . Select “HISTORY”.
1 - 2 . Touch the [ ] key to enter the contact name
] slider
mode (In this case, slide along [
or touch [ ]/[ ] key to select the desired
contact name).
1 - 3 . When the contact name is displayed, touch
the [ ] key to view details.
1 - 4 . When contact name or contact details is
displayed, touch the [ENT] key to call the
mobile phone number.
Note:
Only calls after phone connected with this unit will
be displayed in the history list. There is no synchronization of history calls between connected phone
and this unit.
Redial a Call
You can call a last dialed number of the phone.
1 - 1 . Select “REDIAL”.
1 - 2 . Touch the [ENT] key to redial the last dialed
number of the phone.
Dial Number Call
Outgoing call can be made by entering telephone
numbers.
Telephone number uses 0, 1, 2, 3, 4, 5, 6, 7, 8,
9, ∗, #, and +.
User can search the contact name in the phonebook and make call.
Alternatively, user can call from mobile phone.
FZ709E
31
English
Bluetooth® Operations
Select “DIAL NUMBER”.
Touch the [ ] key to enter the dial mode.
1 - 3 . Touch the [
] or [ ] key to move the cursor.
1 - 4 . Slide along [
] slider or touch [ ]/[ ]
key to select the numbers.
1 - 5 . Touch the [ENT] key to call the mobile phone
number.
1-1.
1-2.
Answering a call
1. You can answer an incoming call by touching
] slider).
any key (except slide along the [
End a call
1. You can reject an incoming call or end an on] slider.
going call by sliding down the [
TEL OPTION
] slider or touch [ ]/
1 . Slide along the [
[ ] key, the TEL OPTION mode changed
as following order:
“PAIRING”
“SELECT”
(“DISCONNECT”)
“DELETE”
(“ADD PHONEBOOK”
“DEL
PHONEBOOK”
“DEL HISTORY”)
“BOOK TYPE”
“RING VOL”
“AUTO ANSWER”
“AUTO
CONNECT”
“PASS KEY”
“ADDRESS”
“BT NAME”
“VERSION”
“PAIRING”...
Notes:
When user pairing at first time, “BOOK TYPE”
is displayed before “PAIRING”. By select book
type once, it appear later in the option list.
The “DISCONNECT” will only appear if paired
mobile phone is connected.
The “ADD PHONEBOOK”, “DEL PHONEBOOK” and “DEL HISTORY” will only appear if
paired mobile phone is connected and selected
Book Type has reserved memory for storing
contacts.
32
FZ709E
BT
OPTION
1 . During BT
mode, touch the [ ] key to
switch to ADJ menu.
2 . Select “OPTION” in the menu to enter the
BT
OPTION mode.
] slider or touch [ ]/
3 . Slide along the [
[ ] key, the BT OPTION mode changed
as following order:
“PAIRING”
“DELETE”
“PASS
KEY”
“ADDRESS”
“BT NAME”
“VERSION”
“PAIRING”...
PAIRING
This option is used to perform Bluetooth® pairing
with the mobile phone and audio.
Up to a maximum of 5 mobile phones and an audio device can be paired.
1 - 1 . Select “PAIRING”.
1 - 2 . Touch the [ ] key to enter detail setting
stage.
1 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “TELEPHONE” or “AUDIO” and
then touch the [ENT] key.
When you select “TELEPHONE”, slide along
[
] slider or touch [ ]/[ ] key to select
“MEMORY 1” to “MEMORY 5”.
1 - 5 . Touch the [ENT] key to enter Pairing mode.
1-4.
Notes:
Activate Pairing mode will disconnect all currently
connected devices.
This unit will not connect to previously connected
device after cancel the Pairing mode.
SELECT
This is a setting for user to select one of the
paired mobile phones.
1 - 1 . Select “SELECT”.
1 - 2 . Touch the [
] key to view the paired mobile
phones list.
1 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to choose one of the 5 mobile phones.
1 - 4 . Touch the [ENT] key to connect. Connected
device will be able to use all the functionalities provided.
Notes:
Make sure Bluetooth® setting on the mobile phone
is turned on during connection request.
“ ” indicator will appear if Bluetooth® device is
connected.
“
” and “
” indicator will only appear if supported by the mobile phone.
DELETE
This is a setting for user to delete one of the
paired devices from the list.
In TEL OPTION:
1 - 1 . Select “DELETE”.
1 - 2 . Touch the [
] key to view the paired mobile
phones list.
1 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to choose one of the 5 mobile phones.
1 - 4 . Touch the [ENT] key, “DELETED?” is displayed.
1 - 5 . Touch the [ENT] key for 2 seconds to delete
the paired device.
In BT
OPTION:
3 - 1 . Select “DELETE”.
3 - 2 . Touch the [ ] key, “DELETED?” is displayed.
3 - 3 . Touch the [ENT] key for 2 seconds to delete
the paired device.
Note:
After a device has been deleted, paired device will
not automatically rearrange in the list.
DISCONNECT
This option is used to disconnect the currently
connected device.
1 - 1 . Select “DISCONNECT”.
1 - 2 . Touch the [ ] key, “DISCONNECT?” is displayed.
1 - 3 . Touch the [ENT] key for 2 seconds to disconnect the connected device.
ADD PHONEBOOK
This option is used to add contacts from the mobile phone.
1 - 1 . Select “ADD PHONEBOOK”.
1 - 2 . Touch the [ENT] key to enter standby mode,
“STAND BY” is blinking.
1 - 3 . During standby mode, use the last connected
mobile phone to send contacts to the unit.
English
Bluetooth® Operations
Notes:
When the “COMPLETED” appears, add phone
book is succeed.
Total contacts that can be stored depend on the
selected Book Type.
DELETE PHONEBOOK
This is a setting for user to delete one or the entire phone numbers.
1 - 1 . Select “DEL PHONEBOOK”.
1 - 2 . Touch the [
] key, the current connected
phone is displayed.
1 - 3 . Touch the [ ENT ] key to enter selection
mode.
1 - 4 . Slide along [
] slider or touch [ ]/[ ]
key to select “ALL DELETE” or “1 DELETE”
and touch [ENT] key.
1 - 5 . When you select “ALL DELETE”, touch the
[ENT] key to proceed.
1 - 6 . When you select “1 DELETE”, slide along
[
] slider or touch [ ]/[ ] key to select
one of the desired phone number and touch
[ENT] key.
1 - 7 . Touch the [ENT] key for 2 seconds to delete.
DELETE HISTORY
This option used to delete the call history.
1 - 1 . Select “DEL HISTORY”.
1 - 2 . Touch the [
] key, “DELETE?” is displayed.
1 - 3 . Touch the [ENT] key for 2 seconds to delete.
FZ709E
33
English
Bluetooth® Operations
BOOK TYPE
The unit provides 3 types of phone book which
are stored in memory.
∗ The factory default setting is “TYPE 3”.
Select “BOOK TYPE”.
1 - 2 . Touch the [
] key to enter detail setting
stage.
1 - 3 . Slide along [
] slider or touch [ ]/[ ] key
to select the setting in sequence “TYPE1”,
“TYPE 2” or “TYPE 3”.
1 - 4 . “ALL MEMORY IS DELETED” is displayed.
1 - 5 . Touch [ENT] key for 2 seconds to change
setting.
1-1.
TYPE
1
PHONE
2
3
MEMORY 1
250 pieces 200 pieces 100 pieces
MEMORY 2
250 pieces 100 pieces 100 pieces
MEMORY 3
0 piece
100 pieces 100 pieces
MEMORY 4
0 piece
50 pieces 100 pieces
MEMORY 5
0 piece
50 pieces 100 pieces
Note:
Once setting is changed, all previous stored phonebook data will be cleared.
RING VOL
This option is used to change the ringing volume
by each paired mobile phone device.
∗ The factory default setting is 5.
(Adjustment level: 1 to 10)
Select “RING VOL”.
Touch the [ ] key to enter detail setting
stage.
1 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to change the ringing volume.
1-1.
1-2.
34
FZ709E
AUTO ANSWER
This is a setting to determine whether any incoming call will be automatically or manually
answered.
∗ The factory default setting is “OFF”.
Select “AUTO ANSWER”.
Touch the [ ] key to enter detail setting
stage.
1 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
1-1.
1-2.
ON
Any incoming call is automatically answered
in 5 seconds.
OFF
User needs to manually answer the call.
AUTO CONNECT
This function allows this unit to be connected automatically with previously connected device.
∗ The factory default setting is “OFF”.
Select “AUTO CONNECT”.
Touch the [ ] key to enter detail setting
stage.
1 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
1-1.
1-2.
ON
Automatic connection is enabled.
OFF
Automatic connection is disabled.
Note:
If user disconnect the device from this unit, the unit
will not try to connect to the device automatically
even if the “AUTO CONNECT” is set to “ON”.
PASS KEY
User can set new 4 digits of pass key that range
from 0 to 9 for pairing authentication security.
This new pass key will be used for subsequent
pairing mode with other Bluetooth® device.
∗ The factory default setting is “1234”.
Select “PASS KEY”.
Touch the [ ] key to enter detail setting
stage.
1 - 3 . Default pass key is displayed. Touch [ENT]
key to change the setting.
1 - 4 . Touch [
] or [ ] key to move the cursor.
1 - 5 . Slide along [
] slider or touch [ ]/[ ]
key to select the desired digits.
1 - 6 . Touch [ENT] key for 2 seconds to store in
memory.
1 - 7 . “MEMORY” is displayed.
1-1.
1-2.
Note:
Both Bluetooth® device and this unit must have the
same pass key in order for pairing to be successful.
Common Operations
Security code
This unit can deter theft by checking registered
security code if security code is registered. The
security code is registered in the Adjustment
mode “CODE” item.
For first time installation, no security code is required.
If security code is registered, changing or disconnecting the vehicle battery will cause the security
code input to be requested for activation. “INPUT
0000” will be displayed and “0000” is blinking.
English
Bluetooth® Operations
] slider or touch [ ]/[ ] key
1. Slide along [
to choose 1~6 to input the security code.
∗ After input first digit, “0000” will stop blinking.
2. Touch [
] key to go on with the next digit.
ADDRESS
This will hold the unique Bluetooth® address. The
address is 12 figures.
1 - 1 . Select “ADDRESS”.
1 - 2 . Touch the [
] key, the Bluetooth® address
appears in the display.
3. Touch [ ] key to confirm during finish input
the 4 security code.
BT NAME
This will hold the unit's name for pairing purpose.
1 - 1 . Select “BT NAME”.
1 - 2 . Touch the [ ] key, the unit's name appears
in the display.
VERSION
This will display the software version of the
Bluetooth®.
1 - 1 . Select “VERSION”.
1 - 2 . Touch the [
] key, the Bluetooth® version
appears in the display.
4. Successful password input will power ON the
unit.
! CAUTION
If entered code is wrong, "----" will be displayed
for a given period during which no operation
can be performed. After the locking peroid,
"INPUT 0000" will be displayed again. For
mistakes less than 7 times, the locking time
will be 15 seconds; from 7th time onwards, the
locking time will be 15 minutes.
FZ709E
35
English
Common Operations
Adjustment Mode
1. Touch the [ ] key to switch to ADJ menu.
2. Select “SETTING” in the menu to enter setting
mode.
] or touch
3. Each time you slide along the [
[ ]/[ ] key, the setting mode changed as
following order:
“DISP BRIGHT”
“BEEP”
“CODE”
“SCREEN SAVER”
“AUTO SCROLL”
“SCROLL SPEED”
“DIMMER”
“BLINKING LED”
“AMP CANCEL”
“INT- SWITCH”
“SYSTEM CHECK”
∗ If no operation is performed for more than 10
seconds, ADJ mode is cancelled and the display
returns to the previous mode.
Setting the code
3-1.
3-2.
Select “CODE”.
Touch [ ] key to enter detail setting stage.
When no code is registered
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the value.
3 - 4 . Touch [
] / [ ] key to set the previous or
next digit.
Setting the display brightness
You can adjust the display brightness to match
the angle of installation of the unit.
∗ The factory default setting is “5”.
(Adjustment level: 1 to 8)
Select “DISP BRIGHT”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the value.
3-1.
3-2.
Notes:
If both the dimmer and the car’s illumination are
turned on, “ILLUMI ON” and the adjustment value
will be displayed. If the dimmer is turned on and
the car’s illumination is turned off, “ILLUMI OFF”
and the adjustment value will be displayed.
If the dimmer is turned off, only the adjustment value
will be displayed.
The display brightness level setting during dimmer
and car’s illumination are turned on has independent adjustment value.
Setting the beep
∗ The factory default setting is “ON”.
Select “BEEP”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3-1.
3-2.
36
FZ709E
3-5.
During finish adjustment, touch [ENT] key
for 2 seconds to memory the new setting
value.
3-6.
“MEMORY XXXX” will be displayed for 2 seconds where “XXXX” is the entered digits.
Note:
Write down your personal code in case you forget
it.
When code is registered
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to input the registered code.
3 - 4 . Touch [
] / [ ] key to set the previous or
next digit.
Turning the screen saver function on
or off
This unit is provided with the screen saver function which allows you to show various kinds of
patterns in the operation status indication area of
the display in a random order. You can turn on or
off this function. If the key operation is performed
with the screen saver function on, the operation display corresponding to the key operation
is shown for about 30 seconds and the display
returns to the screen saver display.
English
Common Operations
∗ The factory default setting is “ON”.
Select “SCREEN SAVER”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3-1.
3-2.
Setting the method for title scroll
Set how to scroll in MP3/WMA/AAC title.
∗ The factory default setting is “ON”.
Select “AUTO SCROLL”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3-1.
3-5.
During finish adjustment, touch [ENT] key for
2 seconds to confirm.
3-2.
ON
To scroll automatically.
3-6.
If successfully delete the registered code,
“DELETED” will be displayed for 2 seconds
and back to 1st item.
OFF
To scroll just 1 time.
Setting the scroll speed
This function allows you to adjust the speed of
the title scroll.
∗ The factory default setting is “3”.
Select “SCROLL SPEED”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to adjust the speed value. (Parameter
range: 1~5)
3-1.
3-2.
3-7.
If unsuccessfully delete the registered code,
“FAILED” will be displayed for 2 seconds and
back to the “INPUT 0000” display.
FZ709E
37
English
Common Operations
Setting the dimmer control
You can set the dimmer control “ON” or “OFF”.
∗ The factory default setting is “ON”.
Select “DIMMER”.
3 - 2 . Touch [
] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3-1.
Anti-theft indicator
The red Anti-theft indicator is a function for preventing theft.
∗ The factory default setting is “OFF”.
Select “BLINKING LED”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3-1.
3-2.
Setting the external amplifier
When an external amplifier is used, the noise can
be decreased by turning off the power supply of
the internal amplifier.
∗ The factory default setting is “OFF”.
Select “AMP CANCEL”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON” or “OFF”.
3-1.
3-2.
ON
Use with connected AMP.
OFF
Use for inside AMP.
Accessory interrupt setting
If you connect this unit and supported accessory
with a separately sold cable, you can listen the
output sound on your car speakers.
∗ The factory default setting is “OFF”.
Select “INT-SWITCH”.
Touch [ ] key to enter detail setting stage.
3 - 3 . Slide along [
] slider or touch [ ]/[ ]
key to select “ON”, “OFF” or “MUTE”.
3-1.
3-2.
38
FZ709E
ON
You can listen from the speakers when
accessory is connected to this unit.
∗ When listening to the connected accessory,
you can adjust the volume by turning the
[ROTARY] knob.
OFF
This unit continues normal operation even
when the accessory is interrupted.
MUTE
The sound from this unit is muted during
accessory is interrupted.
Performing a system check
This function allows you to perform a system
check from the adjust mode when required.
3 - 1 . Select “SYSTEM CHECK”.
3 - 2 . Touch [ENT] key. “SYSTEM CHECK” appears in the display.
3 - 3 . After finish checking, this unit will switch to
previous mode.
AUX function
This system has an external input jack on the
rear panel so you can listen to sounds and music
from external devices connected to this unit.
Selecting AUX IN sensitivity
Make the following settings to select the sensitivity when sounds from external devices connected to this unit are difficult to hear even after
adjusting the volume.
∗ The factory default setting is “MID”.
1. During AUX mode, touch the [ ] key to switch
to ADJ menu.
2. Select OPTION in the menu to enter AUX OPTION mode.
3. Select “AUX SENSE” and touch [ ] key to
enter detail setting stage.
] slider or touch [ ]/[ ] key
4. Slide along [
to select “HIGH”, “MID” or “LOW”.
Note:
When AUX mode is selected, AUX IN sensitivity
can be set.
Problem
Measure
Replace with a fuse of the same amperage.
If the fuse blows again, consult your nearest
service dealers.
Incorrect wiring.
Consult your nearest service dealers.
No sound output when
operating the unit with
a m p l i fi e r s o r p o w e r
antenna attached.
Power antenna lead is
shorted to ground or
excessive current is
required for remote-on
the amplifiers or power
antenna.
1. Turn the unit off.
2. Remove all wires attached to the power
antenna lead. Check each wire for a possible
short to ground using an ohm meter.
3. Turn the unit back on.
4. Reconnect each amplifier remote wire
to the power antenna lead one by one.
If the amplifiers turn off before all wires
are attached, use an external relay to
provide remote-on voltage (excessive current
required).
No sound heard.
The speaker protection
circuit is operating.
1. Turn down sound volume. Function can
also be restored by turning the power off
and on again. (Speaker volume is reduced
automatically when the speaker protection
circuit operates).
2. If the sound is muted again, consult our
service department.
Problem
Cause
Measure
The device contains no
MP3/WMA/AAC files.
Record MP3/WMA/AAC files properly to the
device.
The files are not proper
MP3/WMA/AAC format.
Use only properly encoded MP3/WMA/AAC
files.
Connectors are loose.
Disconnect the device and reconnect
securely.
Sound is interrupted or
has noise.
The MP3/WMA/AAC files
are improperly encoded.
Use only properly encoded MP3/WMA/AAC
files.
The device isn’t
recognized.
The device is damaged.
Disconnect the device and reconnect. If the
device is still not recognized, try replacing with
a different device.
No sound heard.
USB/iPod
Cause
Fuse is blown.
General
Power does not turn on.
(No sound is produced)
Can’t insert the device.
Connectors are loose.
According to the state of
operation on the device,
the communication fault
is caused.
Disconnect the device and reconnect
securely.
The device has been
inserted improperly.
Try reversing the connection direction of the
device (usually the brand name surface should
be facing left).
The connector is broken.
Replace with a new device.
FZ709E
English
6. TROUBLESHOOTING
39
Problem
BT Audio
English
TROUBLESHOOTING
Cause
Measure
Audio streaming is
disconnected after
telephone interrupt.
This is probably happen when audio
streaming and telephone function
are from the same device (mobile
phone).
Dependent on phones.
Reconnect A2DP/AVRCP ( Audio
streaming profiles) from the phone
again after telephone interrupt.
Cannot perform remote
control for audio
streaming.
AVRCP is not connected.
Disconnect and pair the device
again.
Audio streaming will begin
to pulse on/off when using
your connected phone.
Due to excessive Bluetooth® activity
on a low bandwidth link. Some
phones will not handle this well.
If your phone is facing this problem,
please do not use your phone while
audio streaming.
Display is showing device
name connected but there
is no sound output.
The external audio device may in
Pause status.
Some Bluetooth ® audio devices
might not support AVRCP.
Check whether both device and main
unit are in play status. Change the
status in the device if necessary.
If problem persists, please power off
and on the main unit or the device.
There might be connection links
broken between the devices.
Please delete pairing information
on both device and main unit and
start re-pairing.
The device might not support audio
streaming.
Please check your phone whether it
supports Bluetooth® audio streaming
or visit www.clarion.com for your
phone compatibility.
∗ Advanced Audio Distribution Profile (A2DP) is used for Bluetooth® audio streaming support.
∗ Audio Video Remote Control Profile (AVRCP) is used for controlling audio streaming playback.
40
FZ709E
Problem
After pairing, car stereo
is not able to receive and
make calls.
Cause
Bluetooth connection is not
established yet.
Normally it will take several seconds
to establish the connection after
pairing.
Some phones will not automatic
connect after pairing.
®
Measure
Use your phone to manually connect
or select from the unit.
English
TROUBLESHOOTING
Power off and on the car stereo
and perform pairing again. Always
make sure pairing information on
both device and main unit have
been deleted before starting a new
pairing activity.
Telephone
If the problem persists, please visit
www.clarion.com for your phone
compatibility.
Car stereo is connected to other
device.
Disconnect the previous device and
reconnect current device.
Unable to reconnect to
car stereo using phone.
The device pairing information may
have been deleted from the unit.
Perform the above measure.
There is no sound output
when incoming call is
answered.
Incoming call was answered too
quickly before you hear the ringing
tone. This can cause the audio not
properly transferred to the main unit
by some phones.
Please use your phone to transfer
the audio back to the phone for the
current ongoing call.
Kindly answer the call only when you
hear a ringing tone next time.
If the problem persists, please
reconnect the phone or create new
pairing before the next incoming
call.
There is no sound output
during conversation.
Bluetooth® communication link is
lost.
Please disconnect the phone and
reconnect.
If the problem persists, please
create new pairing for both phone
and main unit.
Cannot operate the
handsfree function
properly.
No response from mobile phone.
Turn off and on the mobile phone.
FZ709E
41
English
7. ERROR DISPLAYS
USB/iPod
Error Display
Cause
Measure
ERROR 2
The files are not proper MP3/WMA/
AAC format.
Use only properly encoded MP3/
WMA/AAC files.
ERROR 3
(USB mode)
The MP3/WMA/AAC files are
improperly encoded.
Use only properly encoded MP3/
WMA/AAC files.
The iPod contains no audio files.
Insert an iPod containing audio
files.
Over current detection.
Disconnect the devices and
reconnect. If the devices are still
not recognized, try replacing with a
different devices.
Do not support the HUB devices.
Do not use the HUB devices.
ERROR 3
(iPod mode)
CUR ERR
HUB ERR
Error Display
Cause
Measure
No Bluetooth device is found within
range.
Please turn on the Bluetooth® device
and place the device within range of
reception.
The device pairing information might
have been lost.
Please manually pair and reconnect
the device.
Device or unit is not in pairing mode
or wrong pass key is entered.
Please make sure both the unit and
device is in pairing mode and enter
the correct pass key.
A2DP device is not connected.
Please manually pair and connect the
A2DP device.
BLUETOOTH®
®
FAILED
∗ If an error display other than the ones described above appears, press the reset button. If the problem persists,
turn off the power and consult your nearest service dealers.
42
FZ709E
FM tuner
Folder Level Limit: 8 Level
Usable Sensitivity: 11 dBf
File Support: 255 per folder
Frequency Range: 87.5 MHz to 108 MHz
50 dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation (1 kHz): 35 dB
Frequency Response (±3 dB): 30 Hz to 15 kHz
AM tuner
MW 531 kHz to 1602 kHz
LW 153 kHz to 279 kHz
Usable Sensitivity: 28µV
USB 1.1 and 2.0 compatible with a maximum
transfer rates of up to 12Mbps. (Full speed)
MP3
Decode Format MPEG 1, 2 and 2.5 - Layer 3
Bit-rate (kbps)
WMA
Sampling rate
(kHz)
Bit-rate (kbps)
AAC
Sampling rate
(kHz)
Bit-rate (kbps)
Folder Support: 512
Total File Support: 130560
Folder Name: Maximum 64 single bytes
alphabetical letters
File Name: Maximum 64 single bytes
alphabetical letters
Bluetooth® wireless technology
Compliance: Bluetooth® 2.1
Frequency Range: 2.40~2.4835 GHz, ISM band
RF Power: Class 2 (2.5mW)
Profiles: HFP, A2DP, AVRCP, OPP
USB
Sampling rate
(kHz)
English
8. SPECIFICATIONS
MPEG-1: 32, 44.1, 48
MPEG-2: 16, 22.05, 24
MPEG-2.5: 8, 11.025, 12
MPEG-1: 32 - 320
MPEG-2: 8 - 160
MPEG-2.5: 8 - 160
VBR
32, 44.1, 48
Operating Temperature: -20ºC ~ 60ºC
Telephone Operation:
Noise reduction, Echo cancellation, Full duplex
telephone
Mic Input (External): 2.2k ohm, 2V electret
Audio
Maximum Power Output: 200 W (50 W X 4 ch)
Power Output:
4 X 18 W (DIN 45324, +B=14.4 V)
Bass Control Action (100 Hz): ±14 dB
Middle Control Action (1 kHz): ±14 dB
Treble Control Action (10 kHz): ±14 dB
Line Output (with A/C 1 kHz, 10 kΩ): 4.0 V
32, 36, 40, 44, 48, 64, 128,
160, 192 (WMA V2/V7/V8)
64, 80, 96, 128, 160kbps
(WMA V9L1)
General
48, 44.1, 32, 24, 22.05, 16,
12, 11.025, 8 (kHz)
Current Consumption: Less than 15 A
Speaker Impedance: 4 Ω (4 Ω to 8 Ω allowable)
8-320 kbps
Power Supply Voltage:
12 V DC (10.8 V to 15.6 V allowable), negative
ground
Weight: 1.93 lb. (0.875 kg)
Dimensions:
178 mm Width X 50 mm Height X 154.2 mm
Depth
FZ709E
43
English
SPECIFICATIONS
Notes:
Specifications comply with JEITA Standards.
Specifications and design are subject to change
without notice for further improvement.
Please make sure when connecting external power
amplifier, that you properly, to the car chassis,
ground the amplifier.
If this is not done, severe damage to the source
unit may happen.
44
FZ709E
Download PDF

advertising