Owner`s manual | Clarion VRX935VD Automobile Parts User Manual

English
VRX935VD
Installation and Wire connection manual
1.
2.
3.
4.
5.
6.
7.
8.
9.
BEFORE STARTING ...............................................................
PACKAGE CONTENTS ...........................................................
GENERAL CAUTIONS ............................................................
CAUTIONS ON INSTALLATION ..............................................
INSTALLING THE MAIN UNIT .................................................
REMOVING THE MAIN UNIT ..................................................
CAUTIONS ON WIRING ..........................................................
WIRE CONNECTION ..............................................................
SAMPLE SYSTEMS ................................................................
65
65
66
66
67
69
69
70
73
1. BEFORE STARTING
1. This set is exclusively for use in cars with a
negative ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “v” terminal before starting. This is to prevent short
circuits during installation. (Figure 1)
Car battery
Figure 1
2. PACKAGE CONTENTS
1 Main unit
2 Tuner Amp unit
3 Manuals
Owner’s manual & Installation manual
Warranty card
Guide label for SIRIUS radio
4 Power supply lead (For the main unit)
5 Power supply lead (For the tuner amp
unit)
6 Connection cord (Main unit ↔ Tuner amp unit)
7 Antenna extension cord
8 Bag for accessories of the main unit (No. 1)
Flat head screw (M5 × 8) ............................ 4
Sems hexagonal bolt (M5× 8) ..................... 5
Electro tap
Machine screw (M4× 3) ............................... 4
9 Bag for accessories of the main unit (No. 2)
Hook plate ................................................... 2
Cord clamp
Rubber cap
Special screw
0 Bag for accessories of tuner amp unit
Maunting bracket ......................................... 2
Canoe clip ................................................... 4
Machine screw (M4 × 8) .............................. 4
! Universal mounting bracket
@ Remote control unit
# Battery
(for remote control unit)
$ Outer Escutcheon
% DCP Case
VRX935VD
65
Installation and Wire
connection manual
■ Contents
English
3. GENERAL CAUTIONS
Installation and Wire
connection manual
1. Do not open the case. There are no user serviceable parts inside. If you drop anything
into the unit during installation, consult your
dealer or an authorized CLARION service
centre.
2. Use a soft, dry cloth to clean the case. Never
use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or
warm water to a soft cloth and wipe off the
dirt gently.
4. CAUTIONS ON INSTALLATION
1. Prepare all articles necessary for installing
the main unit before starting.
2. This model is used with the LCD panel slid
forwards (shell loading system). On some
types of cars, the LCD panel may touch the
dashboard or shift lever, in which case it cannot be installed. Check that the set will not
hamper operation of the shift lever before
choosing the place of installation.(Figure 2)
5. Use the enclosed screws for installation. Using other screws can cause damage. (Figure
4)
Chassis
Chassis
Damage
Max. 8 mm (M5 screw)
Dashboard
Figure 4
6. The source unit has mounting screw holes
for NISSAN (N marks) and TOYOTA (T
marks) vehicles.
T
Shift lever
(check that it does not
touch the LCD.)
N
T
Shift lever
Figure 2
3. Install the unit within 30° of the horizontal
plane. (Figure 3)
N
T
Figure 5
Max. 30˚
Figure 3
4. If you have to do any work on the car body,
such as drilling holes, consult your car dealer
beforehand.
66
VRX935VD
N
English
5. INSTALLING THE MAIN UNIT
■ Universal Mount
Notes:
1) Some car models require special mounting kits
for proper installation. Consult your Clarion
dealer for details.
2) Fasten the front stopper securely to prevent the
main unit from coming loose.
7-3/16" (182 mm)
Hole
2-1/16" (53 mm)
• Console opening dimensions
Rear fastening hole (of vehicle)
Instrument panel
Hole
Stoppers
Special Screw
Screwdriver
Rubber cap
Main unit
Universal mounting bracket
Stoppers
2-Spring
Outer escutcheon
Note: Set the outer escutcheon so that its metallic
part on the back side
fits the upper edge of
the main unit.
Figure 6
VRX935VD
67
Installation and Wire
connection manual
1. Place the universal mounting bracket into the
instrument panel, use a screwdriver to bend
each stopper of the universal mounting
bracket inward, then secure the stopper as
shown in Figure 6.
2. Wire as shown in Section 8.
3. Insert the main unit into the universal mounting bracket until it locks.
4. Mount the outer escutcheon so that all the
hooks are locked.
■ Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)
English
Installation and Wire
connection manual
This unit is designed for fixed installation in the
dashboard.
If the vehicle is equipped with a factory-installed
radio, install the main unit with the parts and
screws marked (∗). (Figure 8)
If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install
the main unit in the following procedure.
1. Remove the screws from both side of the
main unit. Then, at either side, lift the leaf
spring until the engaging claws are released
from the holes, and slide the spring to the di-
rection of arrow to remove it. Repeat the
same for the other side to remove the
springs from the both sides. (Figure 7)
2. Secure the mounting brackets to the chassis
as shown in Figure 8. Holes are pre-tapped
for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models.
3. Wire as shown in Section 8.
4. Secure the unit in the dashboard, and then
reassemble the dashboard and the centre
panel.
2-Screw
Engagin claw
Main Unit
2-Spring
Screwdriver
Figure 7
4-Hexagonal screw ∗ (M5 × 8)
Mounting bracket
(1 pair for the left and right sides)
Main Unit
Pocket
Note 2
Centre Panel (Note 1)
∗: The screws with this mark are
enclosed in this set.
★: The parts and screws with this mark
are used to install radio or included in
the installation kit.
Figure 8
Note 1: In some cases, the centre panel may require
some modification (trimming, filling, etc.).
68
VRX935VD
Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with
a nipper or a similar tool.
pull the main unit out by the hook plate. (Insert both the right and left edges of the hook
plate.) (Figure 9)
Note: Keep the hook plate. You cannot remove the
main unit without disengaging the hook plate.
Instrument panel
Universal mounting bracket
2-Hook plate
Main
Unit
Spring
Outer escutcheon
A
B
Figure 9
7. CAUTIONS ON WIRING
1. Be sure to turn the power off before wiring.
2. Be particularly careful where you route the
wires.
Keep them well away from the engine, and
exhaust pipe, etc. Heat may damage the
wires.
3. If the fuse should blow, check to see if the
wiring is correct.
If it is, replace the fuse with a new one with
the same amperage rating as the original.
4. To replace the fuse, remove the old fuse of
the power supply lead and insert the new
one. (Figure10)
∗ Power supply lead for the tuner amp unit : 15A
FUSE
∗ Power supply lead for the main unit : 3A FUSE
Note: There are various types of fuse holder. Do not
let the battery side touch other metal parts.
CAUTION
After the connection, fix the lead by a clamp or
insulation tape for protection.
Fuse
Fuse holder
Figure 10
VRX935VD
69
Installation and Wire
connection manual
1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw.
2. Remove the outer escutcheon.
3. Insert the hook plate between the spring and
the universal mounting bracket, fit tab B of
the spring into hole A of the hook plate, then
English
6. REMOVING THE MAIN UNIT
English
8. WIRE CONNECTION
Installation and Wire
connection manual
Securely connect to the
metal part of the car with a
screw, etc.
Black
Choke coil
Yellow
Power supply lead
Main unit
Main power supply cord
Fuse
Connection cord
(provided with this unit)
CeNET cable (Sold separately)
VIDEO output (RCA) ∗5
Power supply lead
VISUAL 1 audio input
terminal L+R (RCA)
VISUAL 1 video input (RCA)/
DVD changer input (RCA)
&
TV TUNER input (RCA)
Reset switch
Top view of the
tuner amp unit
5.1ch surround decoder select switch ∗3
¥
∗2
$
%
∗6
Rear audio output (input) terminal L+R (RCA) ∗4
Front audio output (input) terminal L+R (RCA) ∗4
Non Fader output terminal L+R (RCA)
70
VRX935VD
Purple/Black
Purple
1
Green/Black
8
0
Green
Brawn
7
*∗1
Glay
Grass-green
Glay/Black
Orange/White
White/Black
Red
White
Yellow
3
)
4
!
6
@
5
9
(
Black
Blue
Installation and Wire
connection manual
Blue/White
English
2
#
¡
No.
1
2
3
4
5
6
7
8
9
0
!
@
#
$
%
¥
&
*
(
)
¡
Description
REAR RIGHTB
REAR RIGHTv
FRONT RIGHTB
FRONT RIGHTv
FRONT LEFTB
FRONT LEFTv
REAR LEFTB
REAR LEFTv
+12 V MAIN POWER
Amplifier turn-on lead
ILLUMINATION
+12 V ACCESSORY
GROUND
CCD camera
VISUAL 2 terminal
Radio antenna jack (∗2)
CeNET terminal
Phone mute (Brown) (∗1)
Spare terminal (Yellow)
Parking brake (Grass-Green)
AUTO ANTENNA
∗1: Connecting the PHONE MUTE Terminal
The lead included with the unit must be connected to the specified position of the vehicle’s
connector in order to use the “triggered audio mute for cellular telephones” function.
∗2: Use the attached extension lead when necessary. (Provided with this unit)
Note : Before making any installation, disconnect the car battery - (negative) cable.
∗3: If a 5.1ch surround decoder (DVH920, sold separately) is connected and the amp of this unit is
used, set the select switch to “LINE IN”. Then the AUDIO OUT (IN) terminal of the Tuner Amp
Unit is only available for audio input, not outputting the audio.
(LINE IN) D
N (LINE OUT)
∗4: Connect to a separately sold external amplifier with a separately sold RCA cord (L, R).
Note : When the 5.1ch surround decoder is connected, these terminals are only available for audio input.
∗5: Connect to a Rear View Monitor (sold separately) for the rear seat.
∗6: Connect to separately sold VTR equipment with a separately sold connection cord.
VRX935VD
71
English
■ Connecting the Accessories
• Connection to the external amplifier
The external amplifier can be connected unless the 5.1ch Surround Decoder is connected. For
detailed information, refer to the instruction manual of the 5.1ch Surround Decoder.
Installation and Wire
connection manual
• Connection to the CCD camera for vehicle
The CCD camera for vehicle can be connected to CCD terminal on the tuner amp unit. For detailed
information, refer to the instruction sheet or manual for the CCD camera.
Notes:
• A power supply box (sold separately) is required for connection of the main unit and the CCD camera.
• The power supply box for camera CAA147 cannot be used. Please use the CAA188 instead.
• If the specified lead of the cellular phone is connected to the phone mute
lead of the source unit, the audio mute is available when the cellular
telephone is used.
• SIRIUS Satellite Radio
When the SIRIUS is to be connected, use the CeNET connector. For detailed information, refer to
the instruction manual of the SIRIUS.
• TV Tunner
When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For
detailed information, refer to the instruction manual of the TV TUNER.
■ Connecting the parking brake lead
Parking brake lamp
+ lead to battery
Connect the lead to parking brake lamp earth
in the meter panel.
Notes:
• Connecting the parking brake lead to lamp earth
allows you to watch TV/VTR/DVD video/video
CD when the parking brake is engaged.
• When the parking brake lead is not connected,
the monitor will stay off.
- cord
parking
brake signal
lead
Connect these three leads.
Parking brake lead
(bright green)
Parking brake
72
VRX935VD
English
9. SAMPLE SYSTEMS
■ Sample System 1
Installation and Wire
connection manual
MAIN UNIT
VRX935VD
RCA Cable
(Visual)
VISUAL 2 IN
VTR
Tuner IN
TTX7501z
(CeNET TV TUNER)
TUNER AMP
UNIT
CeNET
CCA-389
VISUAL 1 IN
Rear view
monitor
CeNET
RCA Cable (Visual)
RCA Cable
(Visual)
DSH920S
(SIRIUS TUNER)
CeNET
VCZ625
(DVD CHANGER)
CeNET Mode*
Front Speaker
Rear Speaker
CCA-519-500
*Switch the MODE switch
to the CeNET mode.
DCZ625
(CD CHANGER)
VRX935VD
73
■ Sample System 2
English
Installation and Wire
connection manual
MAIN UNIT
VRX935VD
Optical Digital Cable
(included the DVH920)
(Gray)
RCA Cable
(Visual)
VISUAL 2 IN
VTR
Tuner IN
TUNER AMP
UNIT
CCA-389
TTX7501z
(CeNET TV TUNER)
CeNET
(LINE IN)D
RCA Cable
(Visual)
RCA Cable
(Visual)
Rear view
monitor
N(LINE OUT)
Set the select switch to
"(LINE IN)D".
CeNET (included
the DVH920)
VISUAL 1 IN
DVH920
(Black)
Optical Digital Cable
(sold separately,
DCA-005/008)
VRX935VD
CeNET
(included the VCZ625)
74
RCA Cable (Visual)
(included the VCZ625)
SRV303
(Powered Sub
Woofer)
RCA Cable (sold separately)
Center Speaker
RCA Cable
Rear Speaker
(included the SRK601)
Front Speaker
(5.1ch surround
decoder)
CeNET Mode∗
VCZ625
(DVD CHANGER)
CeNET Mode∗
(Gray)
∗ Switch the MODE switch
to the CeNET mode.
■ Sample System 3
English
(Gray)
Installation and Wire
connection manual
MAIN UNIT
VRX935VD
Optical Digital Cable
(included the DVH920)
RCA Cable
(Visual)
VISUAL 2 IN
Tuner IN
VTR
TTX7501z
(CeNET TV TUNER)
TUNER AMP
UNIT
CeNET
CeNET
(included the DVH920)
CCA-389
VISUAL 1 IN
(LINE IN)D
N(LINE OUT)
Set the select switch to
"N(LINE OUT)".
Rear view
monitor
RCA cable
RCA Cable (Visual)
RCA Cable
(Visual)
DVH920
(5.1ch surround
decoder)
CeNET Mode∗
RCA cable
Optical Digital Cable
Rear Speaker
(sold separately,
DCA-005/008)
Center Speaker
Front Speaker
CeNET
(included the VCZ625)
RCA Cable (Visual)
(included the VCZ625)
RCA Cable (sold separately)
RCA Cable
(included the SRK601)
Amplifier
(Black)
VCZ625
(DVD CHANGER)
CeNET Mode∗
∗ Switch the MODE switch
to the CeNET mode.
(Gray)
SRV303
(Powered Sub
Woofer)
VRX935VD
75
76
VRX935VD
Download PDF

advertising