Service manual | Clarke STV-20 Vacuum Cleaner User Manual

IVIE Enterprises
www.ivie-ent.com
Ph:(918)254-5161 or (888)262-5161 Fax:(918)250-4807
Service
Manual
STV-20
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If you
cannot read English, have this manual explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 78439A 12/98
CLARKE TECHNOLOGY
Printed in the U.S.A.
230 Volt Machine
Instructions For Connection
To The Power Supply
And The Electrical Ground
This machine must be connected to the electrical
ground to protect the operator from electric shock.
The machine has an approved power cord with two
main conductors and one earthing conductor. Connect the plug to a receptacle as shown in Figure 2.
The green (or green and yellow) conductor in the cord
is the ground wire. Never connect this wire to any
terminal other then the ground terminal.
Make sure you have the correct frequency and
voltage before connecting the power cord to an
outlet. The machine has a plug as shown in
Figure 2. If a receptacle connected to the electrical
ground as shown in Figure 2 is not available, have
one installed by an electrical contractor. Do not use
an adapter.
WARNING:
This machine will operate
only on AC frequency and
electrical voltage shown on
the nameplate. Make sure
you have the correct frequency and voltage before
connecting the power cord
to an outlet. If you are not
sure, consult your electrical
contractor.
WARNING:
Have worn, cut or damaged
cords and plugs replaced by
an authorized service
person.
Pin Earthing Contacts
European Plug
Side Earthing Contacts
Figure 2
After using this machine, follow these instructions:
-
Store the cord on the hook.
Store the machine indoors away from sources
of heat.
This machine is provided with an automatically reset
thermal overload to avoid damage to the motor. If
the thermal overload stops the motor unplug the
machine and follow the procedures below:
-
Empty the vacuum tank.
Shake the filter bag to remove dust.
In a few minutes the thermal overload will
allow restarting of the motor.
CLARKE TECHNOLOGY Operator's Manual STV-20/20D
Page -5-
CLARKE TECHNOLOGY STV-20
Single Motor Assembly Drawing & Parts List 1/98
5
6
7
4
3
2
8
1
9
12
10
11
13
14
15
16
17
18
19
20
24
25
21
22
26
23
27
28
30
40
41
31
32
33
34
35
36
37
38
39
Ref.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
30
31
32
33
34
35
36
37
38
39
40
41
NI
NI
Part No.
51841A
56448A
54503A
56441A
51869A
88304A
54922A
56482A
56441A
88001A
40409A
88304A
52765A
56441A
47316B
54064A
88304A
51872A
57162A
52799A
56483A
56483A
58410A
58414A
56442A
50507A
57877A
56441A
54377A
56039B
56046B
40834A
40835A
54377A
56441A
54377A
57163A
54058A
54059A
57164A
50760A
59859A
56485A
59887A
52944A
Description
Cord, Power
Strain Relief
Cord, Grip
Screw, 5mm x 20mm
Cord, Hook
Screw 5mm x 50mm
Handle, Lift
Screw 5mm x 35mm
Screw, 5mm x 20mm
Screw, 5mm x 14mm
Block, Terminal
Screw, 5mm x 50mm
Cover, Dome
Screw, 5mm x 20mm
Switch, Rocker
Filter, Upper
Screw, 5mm x 50mm
Clip, Spring
Plug, Upper
Cover, Motor
Screw, 5mm x 40mm
Screw, 5mm x 40mm
Support, Motor
Screw, 5mm x 30mm
Screw, 4.3mm x 19mm
Block, Terminal
Ring, Vac Motor
Screw, 5mm x 20mm
Gasket, Vac Motor
Motor, Vac 115V
Motor, Vac 230V
Brush, Carbon 115V
Brush, Carbon 230V
Gasket, Vac Motor
Screw 5mm x 20mm
Gasket, Vac Motor
Plug, Motor
Foam, Triangle
Filter
Plug, Lower
Base, Motor
Washer, Star
Screw, 4mm x 8mm
Wire, Connect
Clip
Qty
1
1
1
2
1
4
1
2
4
2
1
2
1
2
1
1
9
1
2
1
9
3
1
1
1
1
1
4
1
1
1
1
1
1
8
2
2
3
3
2
1
1
1
4
2
NI= Not Illustrated
IVIE Enterprises
www.ivie-ent.com
Page -6-
Ph:(918)254-5161 or (888)262-5161 Fax:(918)250-4807
CLARKE TECHNOLOGY Operator's Manual STV-20/20D
CLARKE TECHNOLOGY STV-20
Filter Bag & Float Assembly Drawing & Parts List 1/98
1
2
3
4
Ref
1
2
3
4
5
6
7
8
5
6
Part No.
58541A
58413A
57856A
54027A
53981A
50339A
50720A
56492A
Description
Spacer, Plastic
Screw, 5mm x 20mm
Cage, Float
Filter
Float
Adapter, Bag
Bag, Filter
Support, Filter Bag
Qty
4
4
1
1
1
1
1
1
To add optional filters for STV-20 or STV-20D order:
54015A Filter, HEPA
1 and 57372A Retainer 1
or
53982A Filter, Cartridge 1 and 57372A Retainer 1
7
8
Wet Vac Tools
Part No.
59213B
59214B
59215A
57503A
59860A
59861A
54887A
Page -8-
Description
Tool, Squeegee
Tool, Floor Brush
Tool, Crevice 38mm
Reducer, Wand
Wand, Extenion 2 Pc.
Wand, Chrome 2 Pc
Hose, 38mm, 2.5m
CLARKE TECHNOLOGY Operator's Manual STV-20/20D
CLARKE TECHNOLOGY STV-20 STV-20D
Tank Assembly & Tilt and Pour Carriage Drawing & Parts List 1/98
1
2
3
4 5
6 7
8
9 10 11
20
19
18
17
12
16
1
13
1
2
3
4
14
15
5
6
7
8
9
10
11 12
13 14
15 16
Tank Assembly
Tilt and Pour Carriage
Ref.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Part No.
54921A
58529A
50460A
57380A
56490A
56441A
51868A
50459A
51184A
59948A
54897A
57853A
56441A
50555A
56481A
52120A
Description
Handle, Transport
Spacer, Hinge
Pivot, Tank Support
Rivet
Support, Handle
Screw, 5mm x 20mm
Carriage, 20 gal.
Pivot, Wheel
Bearing, Spacer
Wheel, 20 gal.
Hub Cap
Ring, Snap
Screw, 5mm x 20mm
Block, Stirrup
Screw, 5mm x 30mm
Caster, Swivel
Qty
1
2
1
4
1
4
1
2
2
2
2
2
8
2
8
2
CLARKE TECHNOLOGY Operator's Manual STV-20/20D
Ref.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Part No.
54920A
51823A
57374A
56481A
87055A
58925A
56481A
57375A
54376A
53166A
50336A
50524A
58692A
87055A
56481A
56481A
87055A
50554A
55008A
55534A
Description
Handle, Assembly
Clamp, Tank
Rivet
Screw, 5mm x 30mm
Washer
Tank, SS 20 gal.
Screw, 5mm x 30mm
Retainer, Poly Tank
Gasket, Tank Adaptor
Deflector, Tank
Adaptor, Hose
Button, Push
Spring, Push Button
Washer
Screw, 5mm x 30mm
Screw, 5mm x 30mm
Washer
Body, Hinge
Hinge, Locking
Knob, Hinge
Qty
2
2
4
8
8
1
4
1
1
1
1
1
1
4
4
4
4
1
2
2
Page -9-
CLARKE TECHNOLOGY STV-20 and STV-20D
Squeegee Tool Drawing & Parts List 1/98
2
1
3
Squeegee Tool - 59213B
Ref.
1
2
3
4
5
6
7
5
6
4
Part No.
50753A
57873A
50357A
53096A
88001A
59970A
53097A
Qty
1
1
1
2
4
2
2
Description
Body, Tool
Ring, Floor Tool
Adapter, Floor Tool
Support, Floor Tool
Screw, 5mm x 15mm
Wheel & Axle
Squeegee Blade
7
CLARKE TECHNOLOGY STV-20 and STV-20D
Floor Brush Tool Drawing & Parts List 1/98
2
1
3
Floor Brush Tool - 59214B
Ref.
1
2
3
4
5
6
7
8
6
5 4
www.ivie-ent.com
Page -10-
7
8
Part No.
50753A
57873A
50357A
53096A
88001A
59970A
51716A
51717A
Qty
1
1
1
2
4
2
1
1
Description
Body, Tool
Ring, Floor Tool
Adaptor, Floor Tool
Support, Floor Tool
Screw, 5mm x 15mm
Wheel & Axle
Brush Guide
Brush Strip, Serrated
IVIE Enterprises
Ph:(918)254-5161 or (888)262-5161 Fax:(918)250-4807
CLARKE TECHNOLOGY Operator's Manual STV-20/20D
Download PDF

advertising