Classe Audio CAP-2100 Stereo Amplifier User Manual

Owner’s Manual
CAP-2100
Integrated Amplifier
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO
NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
NOTICE
All of us at Classé take extreme care to ensure that your purchase will remain a prized investment. We are proud to inform you that all
Classé components have been officially approved for the European Community (CE) mark.
This means that your Classé product was subjected to the most rigorous manufacturing and safety tests in the world. The CE mark certifies
that your purchase meets or exceeds all European Community requirements for unit-to-unit consistency and consumer safety.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna;
Increase the separation between the equipment and the receiver;
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
This product incorporates copyright protection technology that is protected by U.S. patents ad other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses otherwise
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
The information contained in the manual is subject to change without notice. The most current version of this manual will be posted on
our web site at http://www.classeaudio.com.
Marking by the “CE” symbol (shown left) indicates compliance of this device with the EMC
(Electromagnetic Compatibility) and LVD (Low Voltage Directive) standards of the European
Community.
Classé products are designed to comply with international directives on the Restriction of Hazardous
Substances (RoHS) in electrical and electronic equipment and the disposal of Waste Electrical and
Electronic Equipment (WEEE). The crossed wheelie bin symbol indicates compliance and that the
products must be appropriately recycled or processed in accordance with these directives.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Please record the serial number for your new Classé component here for future reference.
Serial #: ____________________________________________
2
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as
vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from
the AC receptacle.
17. The mains plug of the power supply cord shall remain readily operable.
18. Do not expose batteries to excessive heat such as sunshine, fire or the like.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
3
Contents
Welcome to the Classé family ..........................................................................6
a word about installation ...........................................................................6
Unpacking and Placement ...............................................................................7
unpacking your integrated amplifier ..........................................................7
placement ..................................................................................................7
ventilation ..................................................................................................7
custom installations....................................................................................7
serial number .............................................................................................7
register your purchase! ...............................................................................8
operating voltage .......................................................................................8
warm up/break-in period ...........................................................................9
please read this manual .............................................................................9
Special Design Features ..................................................................................10
flexible graphical user interface ...............................................................10
customizable volume control ...................................................................10
highly refined circuit design .....................................................................10
extensive listening tests ............................................................................ 11
extraordinary longevity ............................................................................ 11
Front Panel .....................................................................................................12
Rear Panel ......................................................................................................15
optional phono preamp .....................................................................16
The Remote Control .......................................................................................20
The Menu System ...........................................................................................22
operational menu .....................................................................................22
input selection ...................................................................................22
tape loop ...........................................................................................22
main menu system ...................................................................................23
system setup.............................................................................................23
rotary .................................................................................................24
input ..................................................................................................26
phono gain ...............................................................................................28
triggers .....................................................................................................28
max volume .............................................................................................28
teach IR ....................................................................................................29
display setup ............................................................................................29
brightness ..........................................................................................30
timeout ..............................................................................................30
language ............................................................................................30
main balance ...........................................................................................30
remote Fkeys ............................................................................................31
cautionary note on Fkey use ..............................................................31
status ....................................................................................................... 32
version info....................................................................................... 32
sensors .............................................................................................. 32
4
CAN-Bus .................................................................................................. 32
features .............................................................................................. 32
hardware setup .................................................................................. 33
using CAN-Bus................................................................................... 34
CAN-Bus shared features .......................................................................... 35
configuration...................................................................................... 35
operate............................................................................................... 35
AC status ............................................................................................ 35
status .................................................................................................. 35
name.................................................................................................. 35
global brightness ................................................................................ 36
global standby ................................................................................... 36
CAN-Bus model specific features ............................................................. 36
PlayLink ............................................................................................. 36
amp info ............................................................................................ 37
event log ............................................................................................ 37
Troubleshooting .............................................................................................. 38
Care & Maintenance ....................................................................................... 42
cleaning the cabinet ................................................................................. 42
cleaning the LCD touchscreen.................................................................. 42
installing the remote control batteries ....................................................... 42
Specifications .................................................................................................. 43
Dimensions ..................................................................................................... 44
5
Welcome to the Classé family
Congratulations on your purchase of a Classé product. It is the result of many
years of continuous refinement, and we are sure that you will enjoy it for many
years to come.
We value our relationship with our customers. Please allow us to stay in touch
with you by returning your warranty card now, before you pack up the shipping
carton of your new product and forget all about it. Doing so will enable us to
let you know about any possible future upgrades or updates that might become
available for your Classé component.
Sending in your warranty card also registers your product with us so that
warranty service can be obtained easily and quickly, even if you have mislaid
your original sales slip.
Please, take a few minutes to fill out the warranty
registration card, and drop it in the mail.
You will find the warranty registration card at the end of the separate warranty
policy booklet, enclosed.
a word about installation Every effort has been made to make the Classé CAP-2100 simple and
straightforward to install and use.
Still, we have no way to evaluate many other variables such as the size and shape
of your room, its acoustics, and the associated equipment you have chosen to use
with your amplifier. All of these factors influence the ultimate performance of
your system.
For this reason, we strongly encourage you to have your
system installed and calibrated by your dealer, whose
experience, training, and specialized equipment can
make a profound difference in the final performance of
the system.
6
Unpacking and Placement
unpacking your Carefully unpack your integrated amplifier according to the supplied
integrated amplifier instructions, and remove all accessories from the carton.
Important!
Keep all packing materials for future transport of your
Classé product. Shipping your new component in anything
other than its purpose-designed packing material may
result in damage that is not covered by the warranty.
placement As with any integrated amplifier, it is best to place the CAP-2100 centrally
within your system, since it is the hub to which all other components are
connected. It should also be located at a convenient height for both visibility and
use, since you generally interact with your integrated amplifier more than any
other component (changing inputs, adjusting volume, etc.).
Note that adequate clearance for the AC cord and connecting cables
must be left behind the CAP-2100. We suggest leaving eight inches
(20 cm) of free space behind your integrated amplifier to allow all cables
sufficient room to bend without crimping or undue strain.
Classé recommends that the unit not be placed directly on the top surface of a
power amplifier (or any other heat source).
ventilation Your Classé integrated amplifier generates a certain amount of heat in the course
of normal operation. Be sure to allow six inches of clearance above it and three
inches to each side to allow heat dissipation through air circulation. Avoid
placement on soft surfaces that would restrict airflow (such as plush carpeting).
custom installations Drawings are included in this manual to facilitate special installations and
custom cabinetry (see the section Dimensions). An optional, purpose-designed
rack mount kit is available for this product. Contact your Classé dealer for more
information.
serial number The serial number for your integrated amplifier is found on the rear of the
unit. Please note and record this number on the page entitled Important Safety
Instructions for your future reference.
7
register your purchase! Having found the serial number, now would be a good time to fill out the
registration card. Please register your purchase so we can advise you of updates
and other items of interest.
It will take only a minute or so. Please complete the card now, before you forget.
operating voltage The CAP-2100 integrated amplifier is set at the factory for 100V, 120V, 220V,
230V, or 240V AC mains operation, as appropriate for the country in which
it is to be sold (230V only in European Union countries, in compliance with CE
regulations.) The voltage setting may not be changed by the user.
Make sure that the label on the rear panel of your power amplifier indicates
the correct AC operating voltage for your location. Attempting to operate your
power amplifier at an incorrect voltage may damage the unit.
Warning:
The voltage setting of your power amplifier may not
be changed by the user. There are no user-serviceable
parts within the unit. Please refer any problems to an
authorized Classé service center.
If the AC mains voltage indicated on your integrated amplifier is incorrect,
please contact your local, authorized Classé dealer or distributor.
The CAP-2100 can easily be powered by a normal 15-ampere AC mains line.
If other devices are also powered from the same AC line, their additional power
consumption should be taken into account.
The CAP-2100 includes protection circuitry that will prevent the integrated
amplifier from operating at dangerously high or low voltages.
• At startup: the AC mains voltage must be within a range of
approximately -15% to +10% of its nominal value at startup, or
the amplifier will not turn on. For example, a 120V unit requires
the AC mains to be between approximately 95V–135V in order to
turn on.
• Over-voltage during operation: if the AC mains voltage surges
by roughly 10% or more during operation, the amplifier will enter
protection mode and shut down. The Standby LED will flash to
indicate the protection mode has been engaged.
• Under-voltage during operation: if the AC mains voltage sags by
15% or more, the amplifier will continue to play (since this does
not present a particular danger to the amplifier), but note that
it may not be able to achieve its usual standard of performance
under these compromised conditions. The Standby LED will flash
to indicate the condition.
8
warm up/break-in period Your new Classé integrated amplifier will deliver outstanding performance
immediately. However, you should expect to hear it improve somewhat as
it reaches its normal operating temperatures and its various components
“break-in.” It has been our experience that the greatest changes occur within the
first 300 hours, as the integrated amplifier reaches thermal equilibrium and the
capacitors fully form. After this initial break-in period, the performance of your
new product should remain quite consistent for years to come.
The only exception to this rule is if the unit is unplugged for an extended period
of time, allowing it to cool down. Depending on the degree of cooling involved,
you should expect a brief warm-up period before the sound quality is at its best.
Unless your amplifier was allowed to become quite chilled, subsequent thermal
re-stabilization should not take long. Fortunately, you should never have to
repeat the initial 300 hour break-in period.
please read this manual… Please take a few minutes to review this manual, and to familiarize yourself
with your new integrated amplifier. We understand that you are anxious to plug
everything in and get started. However, reading this manual and following the
advice it gives will ensure that you get all the benefits you deserve from having
purchased such a fine piece of equipment.
9
Special Design Features
flexible graphical The LCD touchscreen on the front panel of your new component supports an
user interface extremely flexible and versatile graphical user interface (GUI) while maintaining
a clean, uncluttered appearance. The CAP-2100 provides a range of controls
that might otherwise require dozens of buttons and knobs on the front panel.
Despite this power and flexibility, it remains simple to operate in day-to-day use.
In fact, in some ways it is even simpler to operate than a more conventional
design might be. For example, if you are not using one or more of the inputs on
your CAP-2100, you can delete the unnecessary buttons from the operational
menu. Doing so prevents anyone from trying to select a non-existent source
component, with the resulting confusion stemming from the lack of any sound.
(Of course, you can easily restore the button if you subsequently add another source
component and need that input.)
customizable The volume control on your new Classé integrated amplifier is controlled by
volume control sophisticated software that allows you to fine-tune its response to suit your
preferences.
Ideally, a volume control would allow you to reach the volume you desire
quickly, and would also provide extremely fine control once you are close to the
“perfect” volume. Of course, these characteristics are in conflict with each other:
one requires the volume to change by quite a lot for a given amount of turning
of the knob, while the other requires small, incremental changes for the same
turn of the knob.
The volume control system on your CAP-2100 solves this problem by
responding differently based on the specific circumstances (e.g., how quickly you
are turning the knob and where in the volume range you are). After extensive
testing, we feel we have created factory default settings that most people will find
intuitive and a real pleasure to use. However, if you feel you would like to finetune its performance further in order to suit your particular preference, you may
easily do so.
highly refined All Classé analog amplification stages are based on circuits that have been
circuit design extensively optimized over many years of continuous development.
By starting with excellent circuit designs and working with them over the years,
we are able to discover the many small refinements that add up to superlative
performance, in a variety of applications. Altering a voltage here, or using a
slightly different part there, may make all the difference between solid and
absolutely outstanding performance.
This level of refinement only comes with a great deal of experience, and is not
available to those who flit from one trendy notion to the next. It accounts
in no small measure for both the consistency of sonic performance among
Classé products (as they are all based on similar analog gain stages), and for the
consistently excellent reviews these products receive from owners and reviewers
alike.
10
extensive listening tests Excellent measured performance is to be expected in world-class products, and
Classé products deliver that performance. However, experience has shown that
technical excellence alone is insufficient to guarantee subjectively musical results.
For this reason, all Classé products are laboriously fine-tuned during the
development process by carefully controlled listening tests. Our ears are still
some of the finest laboratory test instruments available, and nicely complement
more traditional engineering test equipment. In the course of optimizing the
circuitry for a product, hundreds of decisions are made based on the subjective
impression given by substituting one high quality part for another.
As an example, we may listen to half a dozen 0.1% tolerance film resistor
components of the same value, from several different companies. Standard tests
may show them all to provide identical results in terms of noise, distortion, and
so forth. Yet, almost invariably, one selection yields some small improvement in
the subjective reaction to the performance of the product under development.
Less often, even a single such change can result in a surprisingly large
improvement.
Multiply those various improvements by the dozens or even hundreds of such
decisions that must be made before the product can be finalized for production,
and you have a remarkable improvement, indeed – all based on careful listening
tests, which we view as a necessary complement to the solid engineering you
might rightly expect from Classé.
extraordinary longevity Another benefit of having worked with highly refined circuit designs so
extensively over many years is that we have vast experience in what works well
over the long term.
By using only the highest quality parts to begin with, and then using them in an
informed way as a result of both accelerated aging experiments and actual longterm experience, we are able to design and manufacture products which we are
confident will stand the test of time.
We are confident that your new Classé integrated amplifier will give you many
years of trouble-free reliability and musical enjoyment, just as previous Classé
products have given their owners.
11
34!.$"9
-%.5
-54%
#!0
Front Panel
1
Standby button & LED indicator
The front panel Standby button will toggle the integrated amplifier
between operate, its fully operational state, and a standby mode that leaves
the integrated amplifier off, yet ready to respond to system commands via
any of the supported control options (e.g. IR input, DC trigger, CAN-Bus,
or RS-232).
The current state of the integrated amplifier is indicated by the LED on
the standby button on the front panel. When the unit is powered and
switched on, the state of this LED indicates the following:
•
•
•
•
•
on
flashing (on power-up)
off
on (dim)
flashing (after power-up)
=
=
=
=
=
standby
initialization
operate
display timeout
AC mains voltage out of range
If you are planning not to use the integrated amplifier for an extended
period of time, e.g. vacation or other travel, we suggest you disconnect it
from the AC mains. Please be certain that the integrated amplifier is in
standby prior to disconnecting it from the AC mains.
Also, it is a good practice to physically disconnect any and all valuable
electronics from the AC mains during electrical storms, as a lightning strike
anywhere near your home can put a tremendous surge on the AC mains
that can damage any piece of electronics, no matter how well designed
and protected. The best protection in the case of severe electrical storms is
simply to remove the electronics from any connection with the power grid.
12
2
Menu button
Pressing the front panel Menu button will call up the main menu system,
replacing the normal operational menu and status display in the LCD
touchscreen.
3
LCD touchscreen
Much of your interaction with the CAP-2100 will be with the LCD
touchscreen (and the CAP-2100’s supplied remote control). It will usually
display the various input selection buttons you would use in day-to-day
operation, along with access to the tape button.
By pressing the Menu button, you can also call up the main menu system
of the CAP-2100, which gives you control over many of the operational
details of the integrated amplifier, including system setup options, various
display options (including the language in which the menu system itself
displays), and several custom-installation capabilities that allow superior
integration of the CAP-2100 into complex systems.
For more information, see the section The Menu System later in this
manual.
4
Mute button
The front panel Mute button reduces the volume of the integrated
amplifier to zero at the touch of a button. Pressing the button a second
time restores the volume to its previous setting.
However, if you increase the volume manually (using either the volume
knob or the remote control) while the Mute button is engaged, the mute
control will disengage and the volume will be set to zero. This approach
is a safety measure, to avoid situations in which the volume might be
adjusted up while muted, only to then have the system un-muted to an
unexpectedly high volume.
5
IR window
The infrared (IR) receiver and transmitter are located behind this
window. Ordinarily, your Classé CAP-2100 must be able to “see” the
remote control from this window in order to respond to remote control
commands.
If your integrated amplifier will be located behind closed doors, or for any
other reason will not be able to “see” the remote control during normal
operation, you may use the rear panel IR input and output mini-jacks and
an IR repeater system to solve the problem. For more information about
using an infrared repeater system to route signals to and from the
CAP-2100, refer to the section Rear Panel later in this manual, or contact
your local Classé dealer.
13
In addition to receiving IR commands, the CAP-2100 can also transmit IR
commands so they may be learned by third-party learning remote controls.
The CAP-2100 includes a comprehensive list of discrete IR commands
to facilitate the creation of reliable macros. Specifically, there are discrete
codes for all commands that normally operate as “toggle” functions
(e.g. separate operate and standby commands in addition to the normal
command that toggles between the two states).
6
Volume Knob
The large knob on the right side of the front panel of the CAP-2100 is
used to control the volume of the system.
The volume is raised or lowered in precise 0.5dB increments throughout
the range of the control most likely to be used while listening to music.
At extremely low volumes, the step size is increased somewhat to make it
easier to move quickly between extremely low and normal listening levels.
14
2)'(430%!+%2
/540543
).0543
).0543
/540543
/54054
/54054
-!).
/54054
,%&430%!+%2
4!0%
).
4!0%
/54
).
)2
).
,).%
,).%
,).%
0(/./
"!,
/54 /54
42)''%2
/54
"!,
,).%
0(/./
,).%
,).%
4!0%
4!0%
-!).
/54054
23
#!."53
Rear Panel
1
Speaker Outputs
Two pairs of high quality five-way binding posts are provided on each
channel of the integrated amplifier, in order to facilitate bi-wiring.
In practice, bi-wiring involves connecting two (preferably identical) sets
of speaker cables between each amplifier channel and its corresponding
loudspeaker. In many cases, the benefit is a subjectively improved level of
clarity and detail from the speaker, as a result of being able to feed the two
separate sections of its crossover and driver complement with identical, yet
separate signals.
(Many high quality loudspeakers also offer two sets of connections on their
speakers. Generally, one set of the connections on the loudspeaker feeds
the portion of the speaker’s crossover network that supplies the woofer
with its signal; the other set of connections connects to the portion of the
crossover that supplies the rest of the speaker with the midrange and high
frequencies.)
Although the binding posts on your Classé amplifier will accept bare wire
connections, we strongly recommend the use of high quality spade or hook
lugs, crimped and soldered onto the ends of your speaker wires. Using
high quality connectors will ensure that your speaker connections do not
gradually deteriorate from fraying and oxidizing bare wires. It also helps
prevent accidental short-circuits from poorly-terminated connections.
2
Single-ended (RCA) main outputs
Single-ended cables using RCA connectors are the most common form
of analog connection used in consumer electronics. When implemented
carefully and used with high quality interconnect cables, this standard can
provide excellent performance.
15
Classé has gone to extraordinary effort to ensure that the single-ended
(RCA) outputs of your integrated amplifier are as good as possible.
If you need to use these preamplifier-level outputs, connect these singleended outputs to an amplifier using high-quality shielded RCA-terminated
cables. Your Classé dealer can advise you on the selection of cables suitable
for your system.
3
Tape output
Connect these outputs to the right-channel and left-channel recording
inputs of your recorder.
These single-ended RCA outputs are unaffected by the volume control
on the front panel, or by whether you choose to monitor the source or
the recorder (by having the “tape” button on the front panel’s touchscreen
deselected or selected, respectively). The record outputs will be disconnected
when the integrated amplifier is placed into standby, however.
4
Tape Input
Connect the analog outputs of any recording device (analog tape recorder,
digital tape recorder, CD recorder, etc.) you may have to these single-ended
RCA inputs. You may select to hear the output of your recording device by
touching the tape monitor button on the main operational screen of the
CAP-2100.
5
Single-ended (RCA) inputs
These RCA jacks accept right-channel and left-channel (single-ended)
inputs from line-level source equipment such as tuners, CD players,
and tape decks. Any of these inputs may be selected by touching the
corresponding button on the main operational screen of the front panel
touchscreen.
To achieve the best possible results, we suggest that you use only highquality shielded interconnect cables. Please consult with your local Classé
dealer for advice on the best cables for use in your system.
optional phono preamp
If you have a turntable you would like to use with the system, an optional
phono preamplifier module is available from your Classé dealer. Once
installed in your integrated amplifier, the Line 1 input connectors become
your phono inputs, and the phono gain control in the menu system
becomes active, allowing you to select either low gain for all movingmagnet (MM) and high-output moving-coil (MC) cartridges, or high gain
for standard output MC cartridges. (See the section The Menu System for
more information.)
6
16
Balanced (XLR) input
These XLR jacks accept right-channel and left-channel balanced signals
from a source component with balanced outputs. This input may be
selected by touching the corresponding button on the main operational
screen of the front panel touchscreen.
The pin assignments of the XLR input connectors are:
Pin 1: Signal ground
Pin 2: Signal + (non-inverting)
Pin 3: Signal – (inverting)
Connector ground lug: chassis ground
These pin assignments are consistent with the standard adopted by the
Audio Engineering Society (AES14-1992).
Refer to the operating manuals of your balanced-output line-level source to
verify that the pin assignments of its output connectors correspond to the
CAP-2100. If this is not the case, wire the cables so that the appropriate
output pin connects to the equivalent input pin.
To achieve the best possible results, we suggest that you use only highquality interconnect cables. Please consult with your local Classé dealer for
advice on the best cables for use in your system.
7
IR Input and Output
Your Classé integrated amplifier includes two 1/8th-inch mono mini-jacks
in order to support the infrared (IR) remote controls that are ubiquitous
today. Infrared commands exist (for example) for toggling the integrated
amplifier between operate and standby, in addition to discrete command
codes for either operate or standby. These codes may be used in “macros”
for sophisticated remote control systems, facilitating the control of the
integrated amplifier in the larger context of a complete system.
The list of commands available is quite extensive, enabling even complex
macros (chains of commands strung together) to operate flawlessly. If this
capability is of interest to you, we strongly recommend discussing it with
your authorized Classé dealer.
Note that IR Input and Output is a bit of a misnomer: the input and
output of these plugs is electrical in nature, not infrared. They are used
with standard IR receivers, distribution amplifiers, and emitters (available
from your dealer) to translate the remote’s IR signal to an electrical signal
and vice versa. The big advantages here include being able to easily route
the signals anywhere they might need to go and the reliability of a solid
electrical connection.
Since an IR distribution system such as your dealer may design for you
usually must control many products, your integrated amplifier includes
both an IR input (for the control of this product) and an IR output (so
as to pass along the same signal to the next product). This allows you to
“daisy chain” your control wires from one product to the next.
The integrated amplifier is designed to respond to IR commands of
5 VDC, with the tip of the mini-plug defined to be positive relative to the
shank of the plug.
17
8
Classé CAN-Bus Control Ports
These RJ-45 connectors are reserved for future control and communication
applications using Classé Audio’s implementation of the Controller Area
Network (CAN) Bus specification.
9
RS-232 Control Port
This DB-9 connector has two purposes:
• downloading new operating software into your integrated
amplifier (should new features ever be added, for example)
• external control of your integrated amplifier by control systems
such as i-Command™, AMX® and Crestron™
For more information, please contact your dealer and ask about home
automation systems.
10 DC Trigger Input and Output
Many audio/video components can supply a DC control voltage to
associated equipment in order to induce desired behavior. Your Classé
integrated amplifier can take advantage of these capabilities in order to be
switched between operate and standby automatically.
The 1/8th-inch mini-jack Trigger In provides for remote-controlled
turn-on (that is, toggling between operate and standby) of the integrated
amplifier.
Two 1/8th-inch mono mini-jacks provide individually controllable DC
trigger outputs which can be used for any of a number of purposes, as
described in The Menu System. For example, your dealer can program
Trigger Out1 to toggle an outboard Classé power amplifier between
operate and standby with your CAP-2100 (to facilitate the operation of
bi-amped systems).
The remote trigger input will respond to the presence of 5–12VDC, with
tip polarity as shown below:
Similarly, the trigger outputs will create a 12VDC signal that can support
up to 100mA of current.
11 Ground terminal
The ground terminal on your integrated amplifier is most often used for
the ground wire of a turntable, assuming you have the optional phono
module installed (see your authorized Classé dealer for more information
on this option if you are interested).
Connecting the ground wire from your turntable’s tonearm to this screw
terminal usually minimizes any hum or buzzing to which the turntable
might otherwise be susceptible. Your authorized Classé dealer can assist
you in handling this problem if it should arise.
18
12 AC Mains Fuse
An AC mains fuse holder is located next to the AC mains input. It is
unlikely that you should ever have to replace this fuse, but if you do, it is
critical that you do so only with a fuse of exactly the same rating and value
(specified in Troubleshooting #8).
Important!
Never replace a blown fuse on this or any other piece of
electronics with anything other than a fuse of exactly the
same rating and value. Doing so can cause damage to your
electronics that may not be covered by the warranty. .
Always disconnect the integrated amplifier from the AC
mains and from the speakers before attempting to replace
a fuse. If the fuse blows again upon powering back up,
contact your authorized Classé dealer for assistance. .
There are no user-serviceable parts inside the CAP-2100.
13 AC Mains Input
An IEC standard power cord (supplied) is used with the CAP-2100.
Plug the cord into the IEC receptacle provided, and the other end into a
suitable wall outlet.
14 AC Mains Power Switch
The main power switch for the CAP-2100 is located near the middle of
the rear panel, beside the receptacle for the power cord.
The integrated amplifier should be in standby before being switched off.
Switching the unit on puts it in standby mode.
Danger!
Potentially dangerous voltages and current capabilities
exist within your integrated amplifier, even when
disconnected from AC mains. Do not attempt to open any
portion of the integrated amplifier’s cabinet. There are no
user-serviceable parts inside your integrated amplifier.
All service of this product must be referred to a qualified
authorized Classé dealer or distributor.
19
The Remote Control
34!.$"9
,)'(4
).&/
$)30,!9
/
Your new integrated amplifier comes with a versatile remote control which can
control both the CAP-2100 itself and several aspects of the rest of a Classé-based
system. The buttons are arranged in logical groups according to their functions.
1
6/,
).0543%,
-54%
0
Basic Functions
This section along the top of the remote control groups four functions that
control your basic interactions with the CAP-2100.
6/,
4!0%
3%450
%.4%2
"!,
&
• Light switches the backlighting of the remote control on, for
better visibility under low-light conditions. After a few moments
of inactivity, the backlight switches off automatically.
• Info takes you directly to the status screen in the LCD menu
system, displaying several items of information about the
CAP-2100 and its current operational status.
• Disp (for Display) cycles through the three brightness settings of
the screen display.
• Standby toggles the CAP-2100 between standby and operate.
(/-%
&
&
&
1
2
2
Navigation Keys
The central section of the remote control contains the navigation keys. This
array of buttons is similar to what you may have seen on remote controls
for DVD players, and is used for navigation of the menu system of the
CAP-2100.
• Home returns you to the normal input selection controls
normally shown on the LCD screen on the front panel of the
CAP-2100. This provides a quick way to get back to normal
operation, regardless of how deep you might be in the menu
system.
• Menu serves two functions: it calls up the menu system when
you need it in order to adjust something to your preference;
once within the menu system, pressing Menu returns you to the
previous level of the menu system. If you press Menu when at
the top level of the menu system, it will take you back out of the
menu system to the normal display.
• Up/Down/Left/Right keys allow you to move within a
particular menu screen, changing the highlighted item up/down/
left/right as you like, from the comfort of your listening position.
• The Enter key allows you to select the highlighted item, having
the same effect as if you had pressed the button on the LCD
touchscreen.
• The Tape key is not a navigation key, per se, but allows you to
easily toggle between listening to the selected source and listening
to the output of your recording device. If you have a recording
device (such as a three-head tape deck) which can play back a
recording while it is being made, you will be able to compare the
original signal to the recording while you are making it.
20
3
Input Selection
These Up and Down arrow keys will cycle through the active inputs on
your CAP-2100.
If you have inputs you are not using, we suggest deactivating them in order
to provide faster, easier access to the inputs you are actually using. (See the
section The Menu System, the next section in this manual, for information
on how to do this.)
4
System Controls
The CAP-2100 remote control can also control user-defined functions as
well as the volume and mute functions on a Classé system.
• F1/F2/F3/F4 keys are available for controlling aspects of the
CAP-2100 not covered by the other buttons on the remote
control. You are able to choose what the CAP-2100 should do
in response to receiving the infrared signal that a particular Fkey
has been pressed. The list of possible functions is quite extensive,
and is found in the menu system (see the section The Menu
System, the next section in this manual).
Note:
The Fkeys on all Classé remote controls issue the same
infrared commands. This saves you from having to be
sure you have picked up the proper remote, since all your
Classé remotes will perform the same function for each
Fkey.
• Volume Up, Volume Down, and Mute do what you would
expect them to do.
• The Bal (balance) key takes you directly to the balance screen
in the menu system; once there, you can use the navigation keys
on the remote to select either the left or right buttons on the
LCD touchscreen, depending on which way you wish to move
the balance. Adjust the relative left-right balance of the system
by using the Enter key on the remote to “press” the appropriate
button on the display.
21
The Menu System
Your CAP-2100 includes a versatile LCD touchscreen which supports both an
attractive information display and a flexible menu system. While its use is quite
intuitive, it is also quite extensive. This section of the owner’s manual outlines
the many capabilities found in the menu system.
operational menu
The operational menu provides easy access to the most basic functions of the
integrated amplifier: input selection and tape monitor. It also provides both a
numeric and a graphic depiction of the current volume setting
input selection Pressing any of the input buttons on the touchscreen will switch to the
appropriate input. You may have as many as three line inputs (meaning singleended connections using RCA connectors) and one bal input (balanced
connector using an XLR connector). If you do not have this many sources in
your system, you can elect to deactivate the unused inputs. Doing so removes
their associated buttons from the touchscreen, reducing confusion for occasional
users of the system.
tape loop In addition, the CAP-2100 has a dedicated tape loop for use with sources that
can both record and play back, bringing the total number of sources you can
connect to the CAP-2100 to five (four single-ended and one balanced).
When you touch the tape button to highlight it, you will notice that the
previously selected input remains highlighted. Whenever any input is selected
for listening, it is also selected for possible recording; a copy of its signal is sent
to the recording device connected to the tape output. You may record it or not as
you please.
When you select the tape button, you are asking the CAP-2100 to continue
with this recording feed (whether or not it is being used), while switching to
monitor the output of the tape deck (or CD recorder, or whatever else you might
have connected to the record loop). In this way, you can monitor the result of
your recording while you are making it, in real time. (This assumes that your
recording device supports this capability, as do three-head tape decks.)
22
main menu system
Pressing the front panel Menu button to the left of the LCD touchscreen brings
up a comprehensive main menu system, the top two levels of which are shown
above. This menu system provides access to many installation-specific features
that let you customize how the CAP-2100 works within the context of your
particular system.
system setup
The first button on the main menu takes you to a series of submenus that
collectively provide a great deal of control over your system setup. Here, you can:
•
•
•
•
•
customize the behavior of your volume control
tailor your inputs to your particular source components
adjust the gain of the optional phono module
program the behavior of the CAP-2100’s DC triggers
establish a maximum volume setting for your system
23
rotary The rotary knob on the front panel does not directly control the volume.
Instead, it controls circuitry that does so with greater fidelity and precision than
traditional volume potentiometers could ever achieve.
Since the volume control circuitry is under software control, it is possible to
customize its behavior under various conditions. To better understand why this
is so valuable, consider two scenarios:
Person A places a high value on precision in achieving exactly the
volume setting that makes the music most realistic; being able to
easily change volume setting by a fraction of a decibel is critical to his
enjoyment of the system.
Person B just wants to jump easily from low volumes to a reasonable
listening level, and is less concerned with the finer points of precision
than with getting what he wants with a quick twist of the knob.
You can see the problem in these scenarios: Person A wants extremely fine
gradations on the volume control, which will require many rotations to go from
extremely low settings to normal listening levels; Person B wants to get from
one to the other with a “quick twist” of the knob, requiring coarse gradations in
order to cover so much range in so little space. What happens when Persons A
and B live in the same house? Or if Person C wants to have both, depending on
their mood at the moment? (In fact, most of us are probably like Person C.)
Classé solves this dilemma by altering the response of the volume control, based
on several factors.
Since it is rare to listen at extremely low (barely audible) volumes, the low range
adjustment of the volume control allows for faster response to knob input when
the volume setting values are low. When activated, you will get from extremely
low to middle volume control settings a bit faster than you would otherwise.
This effect can be subtle, and may not even be desirable when the speakers used
have extremely high sensitivity (since this results in using the lowest part of the
range more than you would otherwise).
The most significant factor in the perceived responsiveness of the volume control
is the speed at which the knob is being turned. We all naturally tend to move
volume knobs more quickly when we need to make a bigger change, and we
tend to slow down as we approach our desired volume. Thus, if the
CAP-2100 sees the knob moving relatively quickly, it uses coarse steps to
effectively accelerate the action of the circuitry. As the knob begins to turn more
slowly, the CAP-2100 will actually increase the resolution of the steps, which
slows down the action of the volume control and yields greater precision in
choosing an appropriate setting.
24
Of course, it is possible to bump into the knob by accident, which might
result in its spinning very quickly indeed. Rather than increasing the volume
uncontrollably under these conditions, the CAP-2100 actually slows everything
down again as a safety measure against accidentally blowing up your speakers.
In fact, if you like you may establish a speed limit beyond which the knob will
simply be ignored.
The factory default settings for these behaviors are generally found to be intuitive
and a pleasure to use. However, if you prefer to alter these behaviors, you may do
so in the rotary menu, shown below.
All of the rotary setup settings are interactive. You can set the value, and then
adjust the volume to see whether the effect is what you desired.
• low range: determines the degree to which the responsiveness of
the volume control is boosted at low volume control settings, in
order to get through them more quickly. A setting of 0 disengages
the effect, while a setting of 100 maximizes it.
• low speed: determines the responsiveness of the control when the
knob is being turned slowly. A setting of 0 will cause the volume
to change as slowly as possible at low knob speeds; a setting of
100 will cause the volume to change as quickly as allowed at low
knob speeds. (The menu is the same as the one above except for the
indication that it is for the “low speed” adjustment.)
• medium speed: determines the responsiveness of the control
when the knob is being turned at a moderate speed. A setting of
0 will cause the volume to change as slowly as possible at medium
speeds; a setting of 100 will cause the volume to change as quickly
as allowed at medium knob speeds. (The menu is the same as the
one above except for the indication that it is for the “medium speed”
adjustment.)
• high speed: determines the responsiveness of the control when the
knob is being turned rapidly. A setting of 0 will cause the volume
to change as slowly as possible at high knob speeds; a setting of
100 will cause the volume to change as quickly as allowed at high
knob speeds. (The menu is the same as the one above except for the
indication that it is for the “high speed” adjustment.)
25
• speed limit: establishes a maximum rotary speed, beyond which
there will be no change in volume whatsoever; the knob’s input
will be ignored completely until it slows down below the speed
limit.
• reset defaults: if after experimenting with various settings you
decide you prefer it the way it operated as it came from the factory,
pressing this button will restore the factory default settings. So feel
free to experiment – you can always return to the original settings.
input Each input on your integrated amplifier can be customized in several ways to
enhance either the performance or the ease of use of the system. A quick look at
the input menu and submenus gives you an overview of what is possible:
• in use determines whether the selected input is displayed on the
main input selection screen, and whether it is included in the
rotation of inputs cycled through from the remote control’s input
selection buttons.
• name provides a way to customize the names of the inputs as
displayed on the main input selection screen. For example, you
might want to name your Bal input “CDP-100” for the Classé
CD player you might have connected to that input. To do so, use
the four buttons along the bottom of the input name menu to
change the default name of any given input to something more
specific to your system.
• Thebutton acts like the backspace key on a computer
keyboard, moving the cursor to the left and eliminating any
characters along the way.
26
• Thebutton moves the cursor to the right, adding characters
along the way. (Change each character to what you want as you
go along, using the + and – buttons.)
• The + and – buttons change the current character through the
available characters. They include all upper and lower case letters
of the alphabet, the numbers 0-9, and a variety of punctuation.
When done, your main display might look like this (note the
change in what would otherwise be the bal input).
Warning!
When an input is renamed ‘SSP’, it becomes a unity gain
input. When such an input is selected, the volume control of
the CAP-2100 is disabled, all outputs are driven at line level
and the volume indication is removed from the main menu..
This is useful in situations where the CAP-2100 is being
used to pass through a signal coming from a component
with its own volume control (e.g. Classé SSP-300 surround
sound processor), or when one of its outputs is sent to a
component with its own volume control (SSP-300). Care
should be taken to adjust the volume control of the other
component before selecting the SSP input, as the resulting
volume level may be uncomfortably loud.
• input balance adjusts an input-specific balance adjustment to
compensate for the possibility that a particular source might be
slightly imbalanced. This is especially common with turntables,
since even the finest handmade cartridges are subject to small
channel imbalance problems.
• input offset provides a way to compensate for differences in
output level between various source components. Doing so
can eliminate the sometimes annoying and abrupt changes in
volume encountered when switching between different source
components.
27
phono gain
The phono gain menu is only active if the optional phono module is installed;
otherwise it is grayed out. When it is installed, the CAP-2100 will automatically
recognize it, rename the line 1 input to phono, and activate the input on the
main menu.
Setting the phono gain is simple enough: choose low gain for most moving
magnet cartridges, and for high output moving coil cartridges; choose high
gain for low output moving coil cartridges. Your Classé dealer can assist you
in determining what type of cartridge you have, and which setting is most
appropriate.
triggers Each of the CAP-2100’s trigger outputs may be programmed as to its “logic
level,” which is to say, whether its voltage is low (essentially 0V), or high
(approximately 12V) when the trigger is activated. The ability to change the
logic level of a trigger’s “on” state can solve installation-specific problems that
otherwise require external devices that add to both the cost and complexity of
your system.
If this seems an obscure point, that’s okay. It is a feature designed to solve
problems you may not even have, but your installation professional appreciates
being able to easily solve such problems when they occur.
max volume
The max volume screen allows you to establish a maximum volume setting for
your system. This scale runs from 0 to 100, with 100 indicating that you do not
want any artificial limit placed on the maximum gain your integrated amplifier
can provide.
This setting is interactive. You can set the value to something less than 100, and
then adjust the volume to see whether it is appropriate.
28
teach IR
The CAP-2100 provides discrete infrared (IR) command codes for all its
functions, a list that extends far beyond what is required by normal remote
controls. However, many of these functions are critical if you plan to create
a customized remote control with macros that take command of your entire
system. Without these discrete codes, many of the macros you might want to
create will simply not work reliably.
The teach IR screen provides a scrolling list of all the available IR codes in
the CAP-2100. By scrolling to the command you need to learn into your
macrocapable remote, and then pressing the send IR code button, the
CAP-2100 will send the appropriate command code out its front panel–where it
can be learned by your third-party remote control.
For more information on such control systems, we recommend you speak with
your authorized Classé dealer.
display setup
This button brings up the display setup menu. It allows you to configure the
CAP-2100’s LCD screen brightness, the display timeout, and the language used in
the touchscreen and menu system.
29
brightness The brightness setting of the CAP-2100 has three possible values: low, medium,
and high. Select the appropriate setting based on the level of ambient light
typically found in your listening room while using the system. A high brightness
setting usually works best in brightly-lit rooms; you may find that a lower setting
is less visually intrusive under more subdued lighting conditions.
timeout If you prefer listening to music in a dimly-lit or darkened room, you may find
even the low brightness setting of the display somewhat distracting. If so, you
can vary the timeout of the backlighting so as to turn it off entirely after a
period of inactivity you select.
In this context, activity refers to any use of the user interface. This includes hard
buttons, the LCD touchscreen, and the remote control.
For example, if you reduce the timeout to its minimum setting, the backlighting
will illuminate the display as soon as you interact with any of the CAP-2100
controls, and stay on for only three seconds—just long enough for you to check
on something. If you continue to use any of the controls (at least once every
three seconds), the display will remain lit. It will then extinguish itself after three
seconds of inactivity on your part.
If you prefer the display of the CAP-2100 to remain on whenever not in
standby, choose the never timeout setting. The lamp in the LCD display was
designed for harsh automotive environments and will give you many years of
reliable operation. If you plan to leave the unit on continuously, however, we
recommend that you keep the timeout delay set to less than one minute. (Note
that setting the brightness to a lower setting does not increase the life of the lamp.)
language The language menu offers you any of six different languages supported by the
CAP-2100. Classé has provided our international distributors with a software
tool that makes it possible for them to customize the translations to suit their
local customs and terminology, in an effort to ensure that the CAP-2100’s
operation is as intuitive to use in every country as it is in our home country of
Canada.
main balance
The main balance control gives you both a numeric and a graphical indication
of the current balance setting for the CAP-2100. Some recordings are not
balanced particularly well between the left and right channels. If the image
presented by a particular recording seems heavily weighted to the left (for
example), you can restore a more natural perspective with the balance control.
To shift the image to the right, touch the right>> button one or more times as
needed to correct the perceived imbalance.
30
remote Fkeys
The remote control supplied with the CAP-2100 has four function keys (Fkeys)
that allow you to have instant, easy access to specific system functions that might
otherwise be buried in a menu somewhere.
For example, if you use the balance control frequently, you may want to consider
programming one of the Fkeys to take you straight to that screen. Doing so will
save you having to access the control menu, followed by pressing the balance
button (which might be hard to see from across the room).
The remote Fkey menu has four buttons, one each for the four Fkeys on your
remote control. Pressing any of these buttons on the LCD touchscreen takes you
to a subordinate, scrolling list of possible functions for that particular Fkey.
Selecting the one you want is as simple as scrolling through the list (by touching
either the up or down arrows on the right), and then touching the specific
function in the list that you want that Fkey to perform.
cautionary note on Fkey use Note that all Classé remote controls provide these same four Fkeys, so that you
need not worry about which remote you happen to pick up. Thus F1 on the
integrated amplifier’s remote control sends the same infrared signal as F1 on the
CD player’s remote control.
While this is intended to minimize confusion amongst different remotes (since
this aspect of them will all perform identically), you should take care when
assigning different functions on different components to the same Fkey. Doing
so would result in two components doing two different things at once, in
response to a single press of a button on the remote control. This can sometimes
be useful. As an example, F1 could set the integrated amplifier to the CD input,
and also set the CD player to Play, both from the press of a single Fkey.
31
status
The primary function of the status screen is to provide information about the
current operating status of the CAP-2100. It also provides access to version
info screen, which displays information about the unit’s software, and the
sensors screen, which displays information from the internal sensors about the
temperature and input power.
version info The version info button on the status screen takes you to the version
information screen, which displays information on various pieces of software
used by your CAP-2100. If you ever have occasion to call our technical support
people to ask a question not covered in this manual, they may want to know
precisely what version of software your unit is running. Having this information
available will help enable them to give you the best possible service.
sensors The sensors button on the status screen takes you to the sensors screen, which
displays information about several internal sensors within the CAP-2100. It is
unlikely you might ever need the sensor information, unless directed to do so by
a customer service representative at Classé in order to help troubleshoot some
unexpected problem.
CAN-Bus Classé’s Controller Area Network, or CAN-Bus, opens the way to a new level
of interaction between our Delta range of amplifiers, preamps, processors and
source components. When the CAP-2100 is connected with CAN-Bus, the
different elements of a Delta series system are in constant communication,
creating a “global” network that delivers system wide status information and
shared operational features, all through the touchscreen display.
features CAN-Bus will allow a single Delta series touchscreen to:
• Display status information for every connected unit, including
amplifiers which do not have a touchscreen display.
• Create a “PlayLink” that allows an SSP or Preamp to automatically
switch to the correct input when a Delta series source component
starts playback.
• Adjust the global system brightness.
• Configure the entire system to go in and out of standby at the
touch of a button and also bring individual components in and
out of standby.
• Mute any connected unit.
32
hardware setup 1
Classé Delta Series Products
Two or more Classé Delta series products are required, at least one of which
must have a touchscreen display.
2
Category 5 Network Cables
These are ordinary network cables, commonly used for broadband Internet
connections. They should be typical “straight through” cables not the “crossed
over” type, and the total required will be one less than the total number of
Delta series components in your system.
3
CAN-Bus Terminator
A single CAN-Bus Terminator may be required. It is inserted into the
CAN-Bus OUT connector of the last component in the CAN-Bus daisy
chain. One is included in the box with your CAP-2100. They are also
available free of charge from your nearest Classé Customer Support Centre
http://www.Classeaudio.com/support/service.htm
4
SSP-300 & 600 CAN-Bus Interface Box
Systems that include an SSP-600 or SSP-300 will also require an
SSP-300/600 CAN-Bus Interface Box. These are included with the products or
available free of charge from your nearest Classé Customer Support Centre
http://www.Classeaudio.com/support/service.htm
33
The diagrams below illustrate how to connect the CAN-Bus hardware.
Any combination of models in any order without SSP-300 or SSP-600.
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
Any combination of models in any order with SSP-300 or SSP-600.
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
NOTE: Daisy chain may need to be terminated with CAN-Bus Terminator.
using CAN-Bus CAN-Bus is controlled via the touchscreen of any Delta series component. There
is no master component, so Delta series systems where two or more units have
a touchscreen can be controlled through any of the touchscreens. However, it is
probably easiest to start using CAN-Bus through just one.
CAN-Bus is accessed by pressing the menu button on the face of the unit or
remote, then the status button, followed by the more button.
34
The touchscreen will then display the CAN-Bus devices screen, which lists
connected Delta series components by model & serial number.
Highlighting a unit on the CAN-Bus devices screen identifies it as the target
unit. The front panel LEDs of the target unit will start flashing (unless you
highlight the unit that you are using to access CAN-Bus).
Once you have chosen the target unit press select. The target unit’s LEDs will
stop flashing and the touch screen will list the CAN-Bus features available to it.
Some CAN-Bus features are shared by all models, some are specific to individual
models.
CAN-Bus shared features The following CAN-Bus features are shared by all models.
configuration Selecting configuration will present the CAN-Bus configuration screen
allowing access to name, global brightness, and global standby features.
operate The operate settings allow you to bring the target unit in and out of standby, or
mute. This key will be disabled for the unit whose touchscreen you are using to
access CAN-Bus.
AC status The AC status screen displays information from the target unit’s electrical supply
sensors. Two screens are available, with the second accessed by selecting more.
status The status screen is the simplest way to access essential information about
the target unit. It displays the target unit’s model number, software version,
operational status and serial number.
name Allows you to set the name that this component will be listed under in the
CAN-Bus devices screen. The name will appear next to the unit model and serial
number, and facilitate the identification of units in large systems.
35
global brightness By setting all your components to global brightness you can adjust the
touchscreen and LED brightness for your entire system by changing the
brightness of a single touchscreen. All CAN-Bus software updates automatically
set the updated unit to Global Brightness. If you want a particular unit to be
excluded from Global Brightness, deselect Global Brightness for that unit.
global standby By setting all your components to global standby you can bring your entire
system in and out of standby by pressing the standby button of any unit or
remote. All CAN-Bus software updates automatically set the updated unit to
global standby. If you want a particular unit to be excluded from global standby,
deselect global standby for that unit.
CAN-Bus model The following CAN-Bus features are model specific.
specific features
PlayLink This feature is exclusive to Delta series disc players and will only function if
the disc player is connected to a CAN-Bus enabled preamp or surround sound
processor.
When PlayLink is active, pressing play on the disc player will also automatically
switch the preamp/processor to a specified input. This means that you can listen
to a CD or watch a DVD literally at the touch of a button.
The first step in using PlayLink is to choose the input you wish to be selected
when play is pressed on the disc player. Press the PlayLink icon, then select the
correct input from the list.
Once you have selected the input press back, then select configuration.
PlayLink is activated and disabled through the PlayLink icon on the CAN-Bus
configuration screen.
36
PlayLink is automatically active after a software update, and the PlayLink icon
will only appear on the CAN-Bus configuration screen of a Delta series disc
player.
PlayLink can only select a single input per disc player. It is therefore
not designed for users who regularly play both CDs and DVDs
through different inputs from a single disc player. When PlayLink is
active the disc player will default to the same input every time play is
pressed, regardless of whether it is playing CD or DVD.
amp info Available for amplifiers only, this screen displays the data provided by the
heatsink and AC Module temperature sensors.
NOTE: This feature is only accessible when the target amplifier is on.
event log Reserved for amplifiers, this feature is a protection circuitry event log which can
only be accessed when the target amplifier is in standby. The protection circuit
shuts down the amplifier or channel if it overheats or if its output could damage
your speakers. The event log details the circumstances surrounding the amp
going into protection and should be referred to in situations that require the
intervention of your dealer or Classé customer support.
The log can report the following events interpreted as follows:
• +ve slow blo trip & -ve slow blo trip — The average current has
reached the safe operating limit.
• +ve fast blo trip & -ve fast blo trip — The peak current has
reached the safe operating limit.
• over temperature trip — The unit temperature has reached the
safe operating limit.
• DC protection trip — The DC output level has reached the safe
operating limit.
• Communication failure — There has been a loss of
communication between the amp’s system monitoring sensors.
• AC line trip — The power supply has reached the limits of the
amp’s safe operating range.
These events are rare and generally occur due to issues that are external to the
amp. They should be interpreted positively. The amp is doing what it’s designed
to do.
37
Troubleshooting
In general, you should refer any service problems to your Classé dealer. Before
contacting your dealer, check to see if the problem is listed here. If it is, try the
suggested solutions. If none of these solves the problem, contact your Classé
dealer.
1.
Important!
Check that the integrated amplifier is off before checking
any connections between the integrated amplifier and
power amplifier, or between the power amplifier and the
speakers.
2.
Important!
Everything appears to be on, but there is no sound.
• Adjust the volume control to a moderate level (one that should
be audible but is not excessive).
• Make sure the source component for which the input has been
selected is switched on and is out of its standby mode.
• Make sure the proper input has been selected for the source
being used.
• Check that the integrated amplifier is not in mute mode. This is
indicated by the operational menu icon in the form of a speaker
with a bar through it. Press Mute to disengage.
• Check if the tape monitor is enabled. If it is engaged and the
recorder is off, you will not hear the selected source. Disengage
by pressing Tape, unless you wish to monitor the recording.
• If the problem occurs only with a particular input, check the
interconnect cables between that source and the integrated
amplifier.
• If the problem occurs with all inputs, check the speaker wires for
secure connections.
There is no sound and the Standby LED is not lit.
• Ensure the integrated amplifier is plugged into the AC mains and
switched on, and that the AC mains are operating normally. The
unit will automatically attempt to protect itself from improper
AC mains voltages by not powering up.
• If your integrated amplifier was plugged in properly, try the
following: put it in standby, switch off the main power switch in
the back, and unplug the unit for at least thirty seconds before
trying to power it up again. (Sometimes a brownout of short-term
loss of power might require a restart.)
Make sure to power down your integrated amplifier before
doing the restart.
• If none of these solutions work, please consult your Classé dealer
for assistance. Never attempt to replace an internal fuse. There
are no user-serviceable parts inside your unit.
38
3.
Important!
Only one speaker seems to be playing.
• Check the main balance control setting of the CAP-2100 by
pressing the Menu button, followed by the Balance button.
• Does the problem occur with all inputs? If so, check the
interconnect cables between the source component and the
CAP-2100 input. If no fault is found there, check the speaker
wires for secure connections.
Be certain that the integrated amplifier is off before
checking any connections between the speakers and the
integrated amplifier.
• If the problem occurs only with a particular input, check the
input balance control setting of that particular input:
Menu • system setup • input • input name • balance
where input name is the particular input in question.
• If the input balance appears to be correct, check the interconnect
cables between the corresponding source component and the
CAP-2100.
4.
The IR remote control seems not to function.
• Ensure that there are no obstacles between the IR remote and the
IR sensor (located to the right of the Mute button).
• If the batteries are weak, replace them with fresh ones.
• Make sure there are no keys stuck on your Classé remote or on
any other remote control in the room.
5.
There is a hum coming out of the speakers.
• Make sure your single-ended interconnects are not running
alongside any AC power cords. (Long runs of single-ended
interconnects have a natural tendency to pick up noise even if
they are shielded.)
• If any source components connected to your integrated amplifier
has a cable TV hooked up to it, try disconnecting the cable
television line from the source. If the hum goes away, you will
need an isolation device between your cable and that particular
source. Refer to your Classé dealer for one of these inexpensive
devices.
• If you have the optional phono module in your integrated
amplifier, make sure that the ground wire of the tonearm is
secured properly to the ground lug on the back of your preamp.
39
• If the hum exists only on the phono input, make sure
the turntable/tonearm assembly is not too close to other
components. There should be at least 12 inches (30cm) clearance
from the other components. The more clearance you provide, the
better (as long as the tonearm cable is not stretching).
• Make sure the tonearm cable is not touching or running
alongside an AC cable.
• Make sure you have the proper loading for your phono cartridge.
If you are in doubt, consult your authorized Classé dealer.
6.
There is a mechanical hum coming from the unit.
• This symptom suggests you have electrical noise on your AC
mains line. Try connecting to another AC circuit (not merely a
different plug, but a different circuit).
• Check to see if you have any halogen lighting or dimmers on the
same circuit as the integrated amplifier, as they can be the cause
of hum in power supply transformers.
7.
There is a noticeable change in volume between one input
and another, even though I did not adjust the volume.
• You may need to adjust the input offset setting to compensate
for differences in output level between source components.
Alternatively, the input offset setting may have been adjusted
inappropriately. Either way, you can correct the problem by
going to the following location in the menu system:
Menu • system setup • input • input name • offset
where input name is the input you feel needs to be adjusted.
• If the input that seems incorrect is the phono input, make sure
you are using the proper gain setting for the type of cartridge you
are using. If in doubt, consult with your authorized Classé dealer.
8.
The AC mains fuse is blown.
There is a specific troubleshooting procedure for a blown AC mains fuse,
since this rare occurrence sometime indicates a significant problem. Please
carefully follow steps “a” through “e”, in order:
a. Disconnect your integrated amplifier from the AC mains, as
well as from its input connections and speaker connections, and
remove the fuse cover on the rear of the unit.
40
b. If the fuse appears to be blown, replace it only with a fuse of
the same type and rating (specified below). Using any other type
of fuse, particularly a larger-value fuse, can result in permanent
damage to your integrated amplifier. If you are uncomfortable
replacing the fuse yourself, contact your Classé dealer for
assistance.
Mains voltage:
Fuse type:
Rating:
Mains voltage:
Fuse type:
Rating:
100/120VAC
MDL slow-blow
6A
230/240VAC
MDL slow-blow
4A
c. After replacing the fuse and fuse cover, reconnect the integrated
amplifier to the AC mains only and turn it on without
reconnecting either the inputs or the speaker wires. If the fuse blows
again, disconnect it from the AC mains and contact your Classé
dealer for assistance.
d. If everything seems fine, place the integrated amplifier back into
standby and carefully reconnect the input cable and power the
integrated amplifier up. If the fuse then blows (or the integrated
amplifier goes into protection), you may have a serious fault with
your integrated amplifier/processor. Contact your Classé dealer.
e. Finally, if everything is still fine, place the integrated amplifier in
standby and carefully reconnect the speaker wires. Check both
ends of the speaker wires for possible short circuits. Then power
up the integrated amplifier again. If the integrated amplifier
remains functional (the fuse does not blow), then the original
fuse probably blew in order to protect the integrated amplifier
from a large AC mains surge. If it blows again, contact your
Classé dealer for assistance.
9.
The Standby LED is flashing fast, and there is an error
message displayed on the touchscreen LCD.
• Try resetting the unit by disconnecting it from the AC mains
power, waiting a few seconds, and reconnecting the integrated
amplifier to power. If this does not solve the problem, contact
your Classé dealer for assistance.
41
Care and Maintenance
cleaning the cabinet
Caution!
To remove dust from the cabinet of your integrated amplifier, use a feather
duster or a soft, lint-free cloth. To remove dirt and fingerprints, we recommend
isopropyl alcohol and a soft cloth. Dampen the cloth with alcohol first and
then lightly clean the surface of the integrated amplifier with the cloth. Do
not use excessive amounts of alcohol that might drip off the cloth and into the
integrated amplifier.
At no time should liquid cleaners be applied directly
to the surface of the integrated amplifier, as direct
application of liquids may result in damage to electronic
components within the unit.
cleaning the To clean the LCD touchscreen, use a microfiber eyeglass wipe or soft, lint-free
LCD touchscreen cloth, together with a cleaning solution designed for plastic eyeglasses or LCD
computer monitors/televisions.
Important!
Spray the solution onto the cloth or tissue – never directly
onto the touch screen.
installing the The battery compartment is situated at the base of the remote control. Remove
remote control batteries the two screws holding the base plate in place, taking care not to lose them.
Insert the two AA batteries (supplied), ensuring that the polarity is the same as
that indicated on the inner surface of the remote control.
42
Specifications
All specifications are accurate at the time of printing. Classé reserves the right to
adjust specifications without notice.
„ Power output (both channels driven)
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
100W/ch continuous rms @ 8Ω
200W/ch continuous rms @ 4Ω
Frequency response
10Hz – 22kHz (+0/-0.1dB)
10Hz – 155kHz (+0/-3.0dB)
Phase
less than -10° @ 22kHz
Signal-to-noise ratio
95dB typical
Channel separation
better than 95dB @ 20kHz
Noise floor (FFT)
all peaks less than -90dBV
(10Hz – 80kHz)
Distortion (THD + noise)
0.005% @ 8Ω
(unweighted, 0.8Vrms/1kHz input, 10Hz – 80kHz)
Maximum input voltage
3.8Vrms (single-ended)
7.8Vrms (balanced)
Voltage gain range
-100dB to +14dB
Sensitivity (SSP input)
0.5Vrms for rated output (single-ended)
1.0Vrms for rated output (balanced)
Input Impedance
100kΩ
Output Impedance (main output)
100Ω
Input complement
1 balanced (XLR), 4 single-ended (RCA)
Output complement
2 single-ended (RCA)
Crosstalk (any input to any output)
better than -95dB
Rated power consumption (as per IEC60065 - para.2.3.10) 260W
Idle power consumption
125W
Mains voltage
specified on rear panel decal
(cannot be changed by user or dealer)
Dimensions (not incl. controls or connectors)
Width: 17.5” (445mm)
Height: 4.75” (121mm)
Depth: 16.5” (419mm)
Shipping weight
59lbs (27kg)
Net weight
50lbs (23kg)
For more information, see your Classé dealer, or contact:
Classé Audio
5070 François Cusson
Lachine, Quebec
Canada H8T 1B3
Telephone +1 (514) 636-6384
FAX
+1 (514) 636-1428
Internet:
http://www.classeaudio.com
email:
cservice@classeaudio.com
Classé and the Classé logo are trademarks of Classé Audio Inc. of Lachine, Canada. All rights reserved.
i-Command™ is a trademark of Equity International, Inc. All rights reserved.
AMX® is a registered trademark of AMX Corporation of Richardson, TX. All rights reserved.
Crestron™ is a trademark of Crestron Electronics, Inc. of Rockleigh, NJ. All rights reserved.
43
Dimensions
#!0
Ê£n°Î£»
{Èx““
ÊÓ°™ä»
Ç{““
ʙ°nÈ»
Óx䓓
44
Classé Audio
5070 François Cusson
Lachine, Quebec
Canada H8T 1B3
+1 (514) 636-6384
+1 (514) 636-1428 (fax)
http://www.classeaudio.com
email: cservice@classeaudio.com
North America: 1 800 370 3740
email: classe@bwgroupusa.com
Europe: 44 (0) 1903 221 700
email: classe@bwgroup.com
Asia: (852) 2790 8903
email: classe@bwgroup.hk
All Others: +1 514 636 6394
email: cservice@classeaudio.com
Copyright © 2007 Classé Audio, Inc. Printed in Canada.
V 2.1
100107