Instruction manual | Clifford 330X1 Automobile Alarm User Manual

Instructions for use
WASHING MACHINE
Contents
GB
English
GB
Installation, 2-3
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 3
Technical details, 3
Washing machine description, 4-5
Control panel, 4
Leds, 5
Starting and Programmes, 6
Briefly: how to start a programme, 6
Programme table, 6
Personalisations, 7
WIXL 126
Setting the temperature, 7
Functions, 7
Detergents and laundry, 8
Detergent dispenser, 8
Bleach cycle, 8
Preparing your laundry, 8
Special items, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environment, 9
Care and maintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Cleaning the detergent dispenser, 10
Caring for your appliance door and drum, 10
Cleaning the pump, 10
Checking the water inlet hose, 10
Troubleshooting, 11
Service, 12
Before calling for Assistance, 12
1
Installation
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
GB
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
Electric and water connections
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
Connecting the water inlet hose
3. Remove the three
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Use the plug provided to seal the three holes
where the plug was housed, situated on the lower
right-hand side on the rear of your appliance.
6. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
Your machine may make a considerable amount of
noise if the two front feet have not been adjusted
correctly.
1. Install the washing
machine on a flat sturdy
floor, without resting it
up against walls,
furniture cabinets or
other.
2. If the floor is not
perfectly level, compensate for any unevenness
by tightening or
loosening the adjustable
2
front feet (see figure); the angle of inclination,
measured according to the worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
1. Connect the supply
pipe to the water mains
using a gas 3/4
attachment, fitting the
rubber gasket and the
filter supplied with the
appliance and ensuring
that they are fimly
tightened to the taps.
The water supply marked
C must be connected to the cold water tap; the pipe
marked H must be connected to the hot water tap.
Both pipes may be connected to the cold water tap
using the special Y connection with multiple
attachments, supplied with the appliance (see figure).
Before making the connection, allow the water to run
freely until it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Connecting the drain hose
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
When the washing machine is installed, the mains
socket must be within easy reach.
59.5 cm wide
85 cm h igh
56.5 cm deep
Capacity
from 1 to 6 kg
Electric
connections
voltage 230/240 Volts 50 Hz
maximum absorbed pow er 2050 W
Water
connections
maximum pressure 1 MPa (10 bar)
minimu m pressure 0.05 MPa (0.5 bar)
dru m capacity 52 litres
Spin speed
u p to 1200 rpm
Control
programmes
according to
IEC456 directive
programme 2; temperatu re 60°C;
run with a load of 6 kg.
This applian ce is complian t with th e
following European Commun ity
Directives:
- 73/23/CEE of 19/02/73 (L ow
Voltage) an d subsequ en t amen dments
- 89/336/CEE of 03/05/89
(Electromagn etic Compatibility) an d
su bsequ en t amendmen ts
- 200296/CE
Service
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
Dimensions
Troubleshooting
• the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
W IXL 126
Care
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
Model
Precautions
Before plugging the appliance into the mains
socket, make sure that:
• the socket is earthed and in compliance with the
applicable law;
Technical details
Detergents
Electric connection
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
Programmes
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
The first wash cycle
Description
Warning! The company denies all liability if and when
these norms are not respected.
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
GB
Do not use extensions or multiple sockets.
Installation
65 - 100 cm
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
3
Washing machine description
Control panel
GB
FUNCTION
Buttons
Leds
ON-OFF/
DOOR
ON-OFF
LOCK
Button
Led
PROGRAMME
Knob
Detergent dispenser
START/RESET
Button
TEMPERATURE
Knob
Detergent dispenser: to add detergent and fabric
softener (see page 8).
START/RESET button: to start the programmes or
cancel any incorrect settings.
LEDS: to find out which wash cycle phase is under
way.
If the Delay Timer function has been set, the time
left until the programme starts will be indicated (see
page 5).
ON-OFF/DOOR LOCK Led: to find out whether the
washing machine is on and if the appliance door can
be opened (see page 5).
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
PROGRAMME knob: to select the wash
programmes. The knob stays still during the cycle.
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 7).
4
ON/OFF button: to turn the washing machine on
and off.
Leds
Delay set:
If the Delay Timer function has been enabled (see
page. 7), once you have started the programme,
the LED corresponding to the delay set will begin to
flash:
Cycle phase under way:
During the wash cycle, the LEDs gradually
illuminate on to indicate the cycle phase under way:
Prewash
Wash
Spin cycle
Note: during draining, the LED corresponding to
the Spin cycle phase will be turned on.
Once the set delay is complete, the flashing LED will
turn off and the programme set will start.
Detergents
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding
button is illuminated.
If the function selected is incompatible with the
programme set, the button will flash and the
function will not be enabled.
If you set a function that is incompatible with
another function you selected previously, only the
last one selected will be enabled.
Programmes
As time passes, the remaining delay will be
displayed, and the corresponding LED will flash:
Description
Rinse
GB
Installation
The LEDS provide important information.
This is what they can tell you:
Precautions
Care
Troubleshooting
The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED
Service
ON-OFF/DOOR LOCK led:
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before you open the appliance door.
indicates there is an abnormality (see page 11 Troubleshooting).
5
Starting and Programmes
Briefly: starting a programme
GB
7. Start he programme by pressing the START/RESET
1. Switch the washing machine on by pressing button
.
button.
All the LEDS will light up for a few seconds and
To cancel it, keep the START/RESET button pressed
the ON-OFF/DOOR LOCK Led will begin to flash.
for at least 2 seconds.
2. Load your laundry into the washing machine and
8. When the programme is finished, the ON-OFF/
shut the appliance door.
DOOR LOCK Led will flash to indicate that the
3. Set the PROGRAMME knob to the programme
appliance door can be opened. Take out your
required.
laundry and leave the appliance door ajar to allow
4. Set the wash temperature (see page 7).
the drum to dry thoroughly. Turn the washing
6. Add the detergent and any fabric softener (see page 8).
.
machine off by pressing button
Programme table
Typ e of fab ric and
d egree of soil
P rogram m es
Tem perature
D etergent
Fabric
softener
prew as h
w as h
•
•
•
C ycle
Stain rem oval
length
D escrip tion of wash cycle
op tion/b leach
(m inutes)
S tandard
Pre-wash, wash cycle, rinse
cycles, intermediate and final spin
cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse cycles,
intermediate and final spin cycles
Cotton: Extremely soiled whites
1
90 °C
Cotton: Heavily soiled whites
2
60 °C
•
•
2
40 °C
•
•
3
40 °C
•
•
D elicate/
Tradition al
70
4
50 °C
•
•
D elicate
75
4
40 °C
•
•
D elicate
60
5
40 °C
•
•
D elicate
60
Wo o l
6
40 °C
•
•
50
Very d elicate fab rics
7
30 °C
•
•
45
8
60 °C
•
•
65
Wash cycle, rinse cycles,
intermediate and final spin cycles
9
40 °C
•
•
55
Wash cycle, rinse cycles,
intermediate and final spin cycles
10
40 °C
•
•
45
Wash cycle, rinse cycles,
delicate spin cycle
11
30 °C
•
•
30
Wash cycle, rin se cycles an d
delicate spin cycle
Sports shoes (MAX. 2 pairs)
12
30 °C
•
•
50
Cold w ash (w ithout detergents),
wash cycle, rinse cycles, and
delicate spin cycle
Fabrics for sportswear
(Tracksuits, shorts, etc.)
13
30 °C
•
•
60
Wash cycle, rinse cycles,
intermediate and final spin cycles
(sheets, tablecloths, etc.)
and fast colours
Cotton: Heavily soiled whites
and delicate colours
Cotton: Sligh tly soiled w hites
an d delicate colou rs (shirts,
jumpers, etc.)
Synthetics: Heavily soiled fast
colours (baby linen, etc.)
Synthetics: Heavily soiled fast
colours (baby linen, etc.)
Synthetics: Delicate colours (all
types of slightly soiled
garments)
(cu rtain s, silk, visco se, etc.)
D elicate/
Tradition al
D elicate/
Tradition al
D elicate/
Tradition al
125
110
105
Wash cycle, rinse cycles,
intermediate and final spin cycles
Wash cycle, rinse
crease or delicate
Wash cycle, rinse
crease or delicate
cycles, antispin cycle
cycles, antispin cycle
Wash cycle, rinse cycles, anticrease or delicate spin cycle
Wash cycle, rin se cycles, an ticrease an d delicate spin cycle
Wash cycle, rin se cycles, an ticrease or drain in g cycle
Tim e 4 yo u
Cotton: Heavily soiled whites
and fast colours
Cotton: Sligh tly soiled w hites
an d delicate colou rs (shirts,
jumpers, etc.)
Synthetics: Delicate colours (all
types of slightly soiled
garments)
D elicate colours (all types of
slightly soiled garments)
S po rts
PAR TIAL P R OGR AM M E S
R in se
•
D elicate/
Tradition al
R in se cycles an d spin cycle
Spin cycle
Draining and spin cycle
D rain
D rain in g
Notes
-For programmes 8 and 9, we advise against exceeding a wash load of 3.5 kg.
-For programme 13 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
6
Personalisations
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
The temperature can be lowered, or even set to a cold wash ( ).
GB
Installation
Functions
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
Enabled with
programmes:
Delays the start
of the wash by
up to 9 hours.
Press the button repeatedly until the LED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N.B.: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
A ll
W hen this function is set, programmes 4, 5, 6, 7 will end with the
laundry left to soak (Anti-crease) and the Rinse cycle phase
LED
will flash.
- to conclude the cycle, press the START/RESET button ;
- to run the draining cycle alone, set the knob to the relative
symbol
and press the START/RESET button.
3, 4, 5, 6, 7,
8, 9, 10,
Rinse cycle.
Easy iron
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
Extra Rinse
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, 3, 4, 5,
8, 9, 10, 12,
13, Rinse
cycle.
Delay Timer
Reduces the
spin speed.
A ll
programmes
ex cept for 7
and draining.
Precautions
$
Detergents
Comments
Programmes
Effect
Function
Description
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Care
Troubleshooting
Service
7
Detergents and laundry
Detergent dispenser
GB
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
1
2
3
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
Preparing your laundry
• Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
• Empty all pockets and check for loose buttons.
• Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 6 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1,5 kg
How much does your laundry weigh?
compartment 1: Detergent for pre-wash
(powder)
Before pouring in the detergent, make sure that
extra compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
Do not use hand wash detergent because it may
form too much foam.
8
1
1
1
1
1
sheet 400-500 g
pillow case 150-200 g
tablecloth 400-500 g
bathrobe 900-1,200 g
towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 7
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1,5 kg.
Precautions and advice
• This appliance has been designed for nonprofessional, household use and its functions must
not be changed.
• Disposing of an old washing machine:
before scrapping your appliance, cut the power
supply cable and remove the appliance door.
• This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Saving energy and respecting the
environment
• Never touch the washing machine when barefoot
or with wet or damp hands or feet.
• Do not open the detergent dispenser while the
appliance is in operation.
• Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
• Always keep children well away from the
appliance while in operation.
• The appliance door tends to get quite hot during
the wash cycle.
Disposal
• If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
• If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
Service
• Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment.
• Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
Troubleshooting
• Before loading your laundry into the washing
machine, make sure the drum is empty.
• Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
Care
• Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
• The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Precautions
• In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Saving on detergent, water,
energy and time
• To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
Detergents
• Do not touch the drain water as it could reach
very high temperatures.
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest technology,
your washing machine only needs less than half the
amount of water to get the best results: an objective
reached to respect the environment.
Programmes
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
GB
Description
General safety
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Installation
The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read
carefully.
9
Care and maintenance
Cutting off the water or electricity
supply
GB
• Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
• Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
2. unscrew the lid
rotating it anticlockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
Caring for your appliance door and
drum
• Always leave the appliance door ajar to prevent
unpleasant odours from forming.
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
Never use hoses that have already been used.
10
Troubleshooting
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem
can't easily be solved by consulting the following list.
Possible causes/Solution:
The washing machine won't
start.
• The appliance is not plugged into the socket, or not enough to
make contact.
• There has been a power failure.
The wash cycle won't start.
•
•
•
•
•
•
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The washing machine leaks.
• The water inlet hose is not screwed on correctly (see page 2).
• The detergent dispenser is obstructed (to clean it, see page 10).
• The drain hose is not secured properly (see page 3).
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same
time as at least one other LED.
• This means there is a problem with the machine. Before calling
Assistance, please follow the set of instructions below:
1. Switch off the machine.
2. Remove the plug connecting the appliance to the mains supply and
wait for at least 40 seconds.
3. Place the plug back into the socket.
4. Switch on the machine.
5. If the problem is still evident after this process has been carried out,
contact Assistance.all for Assistance because this means there is an
abnormality.
• The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
• You used too much detergent.
There is too much foam.
Service
• When the machine is installed, the locking screws for the oscillating
assembly are still in place. Remove the screws (see page 2).
• The washing machine is not level (see page 2).
• The washing machine is closed in between furniture cabinets and
the wall (see page 2).
Troubleshooting
The washing machine vibrates
too much during the spin cycle.
Care
• The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
• The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
• The drain hose is bent (see page 3).
• The drain duct is clogged.
Precautions
The washing machine does not
drain or spin.
Detergents
• The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
• The free end of the hose is underwater (see page 3).
• The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
washing machine to load and unload water continuously. In order to avoid
such an inconvenience, special anti-drain trap valves are available in shops.
Programmes
The washing machine
continuously loads and unloads
water.
The appliance door is not shut properly.
The
button has not been pressed.
The START/RESET button has not been pressed.
The water tap is not turned on.
A delayed start has been set (using the Delay Timer, see page 7).
Description
The washing machine fails to
load water.
•
•
•
•
•
GB
Installation
Problem
11
Service
195053267.00
07/2005 - Xerox Business Services
Before calling for Assistance:
• Check whether you can solve the problem on your own (see page 11);
• Restart the programme to check whether the problem has been solved;
• If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
GB
.
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout
service
Always request the assistance of authorised servicemen.
Service
Notify the operator of:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
12
Download PDF

advertising